1 // SPDX-License-Identifier: GPL-2.0-only 2 /******************************************************************************* 3 This contains the functions to handle the platform driver. 4 5 Copyright (C) 2007-2011 STMicroelectronics Ltd 6 7 8 Author: Giuseppe Cavallaro <peppe.cavallaro@st.com> 9 *******************************************************************************/ 10 11 #include <linux/device.h> 12 #include <linux/platform_device.h> 13 #include <linux/pm_runtime.h> 14 #include <linux/module.h> 15 #include <linux/io.h> 16 #include <linux/of.h> 17 #include <linux/of_net.h> 18 #include <linux/of_mdio.h> 19 20 #include "stmmac.h" 21 #include "stmmac_platform.h" 22 23 #ifdef CONFIG_OF 24 25 /** 26 * dwmac1000_validate_mcast_bins - validates the number of Multicast filter bins 27 * @dev: struct device of the platform device 28 * @mcast_bins: Multicast filtering bins 29 * Description: 30 * this function validates the number of Multicast filtering bins specified 31 * by the configuration through the device tree. The Synopsys GMAC supports 32 * 64 bins, 128 bins, or 256 bins. "bins" refer to the division of CRC 33 * number space. 64 bins correspond to 6 bits of the CRC, 128 corresponds 34 * to 7 bits, and 256 refers to 8 bits of the CRC. Any other setting is 35 * invalid and will cause the filtering algorithm to use Multicast 36 * promiscuous mode. 37 */ 38 static int dwmac1000_validate_mcast_bins(struct device *dev, int mcast_bins) 39 { 40 int x = mcast_bins; 41 42 switch (x) { 43 case HASH_TABLE_SIZE: 44 case 128: 45 case 256: 46 break; 47 default: 48 x = 0; 49 dev_info(dev, "Hash table entries set to unexpected value %d\n", 50 mcast_bins); 51 break; 52 } 53 return x; 54 } 55 56 /** 57 * dwmac1000_validate_ucast_entries - validate the Unicast address entries 58 * @dev: struct device of the platform device 59 * @ucast_entries: number of Unicast address entries 60 * Description: 61 * This function validates the number of Unicast address entries supported 62 * by a particular Synopsys 10/100/1000 controller. The Synopsys controller 63 * supports 1..32, 64, or 128 Unicast filter entries for it's Unicast filter 64 * logic. This function validates a valid, supported configuration is 65 * selected, and defaults to 1 Unicast address if an unsupported 66 * configuration is selected. 67 */ 68 static int dwmac1000_validate_ucast_entries(struct device *dev, 69 int ucast_entries) 70 { 71 int x = ucast_entries; 72 73 switch (x) { 74 case 1 ... 32: 75 case 64: 76 case 128: 77 break; 78 default: 79 x = 1; 80 dev_info(dev, "Unicast table entries set to unexpected value %d\n", 81 ucast_entries); 82 break; 83 } 84 return x; 85 } 86 87 /** 88 * stmmac_axi_setup - parse DT parameters for programming the AXI register 89 * @pdev: platform device 90 * Description: 91 * if required, from device-tree the AXI internal register can be tuned 92 * by using platform parameters. 93 */ 94 static struct stmmac_axi *stmmac_axi_setup(struct platform_device *pdev) 95 { 96 struct device_node *np; 97 struct stmmac_axi *axi; 98 99 np = of_parse_phandle(pdev->dev.of_node, "snps,axi-config", 0); 100 if (!np) 101 return NULL; 102 103 axi = devm_kzalloc(&pdev->dev, sizeof(*axi), GFP_KERNEL); 104 if (!axi) { 105 of_node_put(np); 106 return ERR_PTR(-ENOMEM); 107 } 108 109 axi->axi_lpi_en = of_property_read_bool(np, "snps,lpi_en"); 110 axi->axi_xit_frm = of_property_read_bool(np, "snps,xit_frm"); 111 axi->axi_kbbe = of_property_read_bool(np, "snps,kbbe"); 112 axi->axi_fb = of_property_read_bool(np, "snps,fb"); 113 axi->axi_mb = of_property_read_bool(np, "snps,mb"); 114 axi->axi_rb = of_property_read_bool(np, "snps,rb"); 115 116 if (of_property_read_u32(np, "snps,wr_osr_lmt", &axi->axi_wr_osr_lmt)) 117 axi->axi_wr_osr_lmt = 1; 118 if (of_property_read_u32(np, "snps,rd_osr_lmt", &axi->axi_rd_osr_lmt)) 119 axi->axi_rd_osr_lmt = 1; 120 of_property_read_u32_array(np, "snps,blen", axi->axi_blen, AXI_BLEN); 121 of_node_put(np); 122 123 return axi; 124 } 125 126 /** 127 * stmmac_mtl_setup - parse DT parameters for multiple queues configuration 128 * @pdev: platform device 129 * @plat: enet data 130 */ 131 static int stmmac_mtl_setup(struct platform_device *pdev, 132 struct plat_stmmacenet_data *plat) 133 { 134 struct device_node *q_node; 135 struct device_node *rx_node; 136 struct device_node *tx_node; 137 u8 queue = 0; 138 int ret = 0; 139 140 /* For backwards-compatibility with device trees that don't have any 141 * snps,mtl-rx-config or snps,mtl-tx-config properties, we fall back 142 * to one RX and TX queues each. 143 */ 144 plat->rx_queues_to_use = 1; 145 plat->tx_queues_to_use = 1; 146 147 /* First Queue must always be in DCB mode. As MTL_QUEUE_DCB = 1 we need 148 * to always set this, otherwise Queue will be classified as AVB 149 * (because MTL_QUEUE_AVB = 0). 150 */ 151 plat->rx_queues_cfg[0].mode_to_use = MTL_QUEUE_DCB; 152 plat->tx_queues_cfg[0].mode_to_use = MTL_QUEUE_DCB; 153 154 rx_node = of_parse_phandle(pdev->dev.of_node, "snps,mtl-rx-config", 0); 155 if (!rx_node) 156 return ret; 157 158 tx_node = of_parse_phandle(pdev->dev.of_node, "snps,mtl-tx-config", 0); 159 if (!tx_node) { 160 of_node_put(rx_node); 161 return ret; 162 } 163 164 /* Processing RX queues common config */ 165 if (of_property_read_u32(rx_node, "snps,rx-queues-to-use", 166 &plat->rx_queues_to_use)) 167 plat->rx_queues_to_use = 1; 168 169 if (of_property_read_bool(rx_node, "snps,rx-sched-sp")) 170 plat->rx_sched_algorithm = MTL_RX_ALGORITHM_SP; 171 else if (of_property_read_bool(rx_node, "snps,rx-sched-wsp")) 172 plat->rx_sched_algorithm = MTL_RX_ALGORITHM_WSP; 173 else 174 plat->rx_sched_algorithm = MTL_RX_ALGORITHM_SP; 175 176 /* Processing individual RX queue config */ 177 for_each_child_of_node(rx_node, q_node) { 178 if (queue >= plat->rx_queues_to_use) 179 break; 180 181 if (of_property_read_bool(q_node, "snps,dcb-algorithm")) 182 plat->rx_queues_cfg[queue].mode_to_use = MTL_QUEUE_DCB; 183 else if (of_property_read_bool(q_node, "snps,avb-algorithm")) 184 plat->rx_queues_cfg[queue].mode_to_use = MTL_QUEUE_AVB; 185 else 186 plat->rx_queues_cfg[queue].mode_to_use = MTL_QUEUE_DCB; 187 188 if (of_property_read_u32(q_node, "snps,map-to-dma-channel", 189 &plat->rx_queues_cfg[queue].chan)) 190 plat->rx_queues_cfg[queue].chan = queue; 191 /* TODO: Dynamic mapping to be included in the future */ 192 193 if (of_property_read_u32(q_node, "snps,priority", 194 &plat->rx_queues_cfg[queue].prio)) { 195 plat->rx_queues_cfg[queue].prio = 0; 196 plat->rx_queues_cfg[queue].use_prio = false; 197 } else { 198 plat->rx_queues_cfg[queue].use_prio = true; 199 } 200 201 /* RX queue specific packet type routing */ 202 if (of_property_read_bool(q_node, "snps,route-avcp")) 203 plat->rx_queues_cfg[queue].pkt_route = PACKET_AVCPQ; 204 else if (of_property_read_bool(q_node, "snps,route-ptp")) 205 plat->rx_queues_cfg[queue].pkt_route = PACKET_PTPQ; 206 else if (of_property_read_bool(q_node, "snps,route-dcbcp")) 207 plat->rx_queues_cfg[queue].pkt_route = PACKET_DCBCPQ; 208 else if (of_property_read_bool(q_node, "snps,route-up")) 209 plat->rx_queues_cfg[queue].pkt_route = PACKET_UPQ; 210 else if (of_property_read_bool(q_node, "snps,route-multi-broad")) 211 plat->rx_queues_cfg[queue].pkt_route = PACKET_MCBCQ; 212 else 213 plat->rx_queues_cfg[queue].pkt_route = 0x0; 214 215 queue++; 216 } 217 if (queue != plat->rx_queues_to_use) { 218 ret = -EINVAL; 219 dev_err(&pdev->dev, "Not all RX queues were configured\n"); 220 goto out; 221 } 222 223 /* Processing TX queues common config */ 224 if (of_property_read_u32(tx_node, "snps,tx-queues-to-use", 225 &plat->tx_queues_to_use)) 226 plat->tx_queues_to_use = 1; 227 228 if (of_property_read_bool(tx_node, "snps,tx-sched-wrr")) 229 plat->tx_sched_algorithm = MTL_TX_ALGORITHM_WRR; 230 else if (of_property_read_bool(tx_node, "snps,tx-sched-wfq")) 231 plat->tx_sched_algorithm = MTL_TX_ALGORITHM_WFQ; 232 else if (of_property_read_bool(tx_node, "snps,tx-sched-dwrr")) 233 plat->tx_sched_algorithm = MTL_TX_ALGORITHM_DWRR; 234 else 235 plat->tx_sched_algorithm = MTL_TX_ALGORITHM_SP; 236 237 queue = 0; 238 239 /* Processing individual TX queue config */ 240 for_each_child_of_node(tx_node, q_node) { 241 if (queue >= plat->tx_queues_to_use) 242 break; 243 244 if (of_property_read_u32(q_node, "snps,weight", 245 &plat->tx_queues_cfg[queue].weight)) 246 plat->tx_queues_cfg[queue].weight = 0x10 + queue; 247 248 if (of_property_read_bool(q_node, "snps,dcb-algorithm")) { 249 plat->tx_queues_cfg[queue].mode_to_use = MTL_QUEUE_DCB; 250 } else if (of_property_read_bool(q_node, 251 "snps,avb-algorithm")) { 252 plat->tx_queues_cfg[queue].mode_to_use = MTL_QUEUE_AVB; 253 254 /* Credit Base Shaper parameters used by AVB */ 255 if (of_property_read_u32(q_node, "snps,send_slope", 256 &plat->tx_queues_cfg[queue].send_slope)) 257 plat->tx_queues_cfg[queue].send_slope = 0x0; 258 if (of_property_read_u32(q_node, "snps,idle_slope", 259 &plat->tx_queues_cfg[queue].idle_slope)) 260 plat->tx_queues_cfg[queue].idle_slope = 0x0; 261 if (of_property_read_u32(q_node, "snps,high_credit", 262 &plat->tx_queues_cfg[queue].high_credit)) 263 plat->tx_queues_cfg[queue].high_credit = 0x0; 264 if (of_property_read_u32(q_node, "snps,low_credit", 265 &plat->tx_queues_cfg[queue].low_credit)) 266 plat->tx_queues_cfg[queue].low_credit = 0x0; 267 } else { 268 plat->tx_queues_cfg[queue].mode_to_use = MTL_QUEUE_DCB; 269 } 270 271 if (of_property_read_u32(q_node, "snps,priority", 272 &plat->tx_queues_cfg[queue].prio)) { 273 plat->tx_queues_cfg[queue].prio = 0; 274 plat->tx_queues_cfg[queue].use_prio = false; 275 } else { 276 plat->tx_queues_cfg[queue].use_prio = true; 277 } 278 279 plat->tx_queues_cfg[queue].coe_unsupported = 280 of_property_read_bool(q_node, "snps,coe-unsupported"); 281 282 queue++; 283 } 284 if (queue != plat->tx_queues_to_use) { 285 ret = -EINVAL; 286 dev_err(&pdev->dev, "Not all TX queues were configured\n"); 287 goto out; 288 } 289 290 out: 291 of_node_put(rx_node); 292 of_node_put(tx_node); 293 of_node_put(q_node); 294 295 return ret; 296 } 297 298 /** 299 * stmmac_of_get_mdio() - Gets the MDIO bus from the devicetree. 300 * @np: devicetree node 301 * 302 * The MDIO bus will be searched for in the following ways: 303 * 1. The compatible is "snps,dwc-qos-ethernet-4.10" && a "mdio" named 304 * child node exists 305 * 2. A child node with the "snps,dwmac-mdio" compatible is present 306 * 307 * Return: The MDIO node if present otherwise NULL 308 */ 309 static struct device_node *stmmac_of_get_mdio(struct device_node *np) 310 { 311 static const struct of_device_id need_mdio_ids[] = { 312 { .compatible = "snps,dwc-qos-ethernet-4.10" }, 313 {}, 314 }; 315 struct device_node *mdio_node = NULL; 316 317 if (of_match_node(need_mdio_ids, np)) { 318 mdio_node = of_get_child_by_name(np, "mdio"); 319 } else { 320 /** 321 * If snps,dwmac-mdio is passed from DT, always register 322 * the MDIO 323 */ 324 for_each_child_of_node(np, mdio_node) { 325 if (of_device_is_compatible(mdio_node, 326 "snps,dwmac-mdio")) 327 break; 328 } 329 } 330 331 return mdio_node; 332 } 333 334 /** 335 * stmmac_mdio_setup() - Populate platform related MDIO structures. 336 * @plat: driver data platform structure 337 * @np: devicetree node 338 * @dev: device pointer 339 * 340 * This searches for MDIO information from the devicetree. 341 * If an MDIO node is found, it's assigned to plat->mdio_node and 342 * plat->mdio_bus_data is allocated. 343 * If no connection can be determined, just plat->mdio_bus_data is allocated 344 * to indicate a bus should be created and scanned for a phy. 345 * If it's determined there's no MDIO bus needed, both are left NULL. 346 * 347 * This expects that plat->phy_node has already been searched for. 348 * 349 * Return: 0 on success, errno otherwise. 350 */ 351 static int stmmac_mdio_setup(struct plat_stmmacenet_data *plat, 352 struct device_node *np, struct device *dev) 353 { 354 bool legacy_mdio; 355 356 plat->mdio_node = stmmac_of_get_mdio(np); 357 if (plat->mdio_node) 358 dev_dbg(dev, "Found MDIO subnode\n"); 359 360 /* Legacy devicetrees allowed for no MDIO bus description and expect 361 * the bus to be scanned for devices. If there's no phy or fixed-link 362 * described assume this is the case since there must be something 363 * connected to the MAC. 364 */ 365 legacy_mdio = !of_phy_is_fixed_link(np) && !plat->phy_node; 366 if (legacy_mdio) 367 dev_info(dev, "Deprecated MDIO bus assumption used\n"); 368 369 if (plat->mdio_node || legacy_mdio) { 370 plat->mdio_bus_data = devm_kzalloc(dev, 371 sizeof(*plat->mdio_bus_data), 372 GFP_KERNEL); 373 if (!plat->mdio_bus_data) 374 return -ENOMEM; 375 376 plat->mdio_bus_data->needs_reset = true; 377 } 378 379 return 0; 380 } 381 382 /** 383 * stmmac_of_get_mac_mode - retrieves the interface of the MAC 384 * @np: - device-tree node 385 * Description: 386 * Similar to `of_get_phy_mode()`, this function will retrieve (from 387 * the device-tree) the interface mode on the MAC side. This assumes 388 * that there is mode converter in-between the MAC & PHY 389 * (e.g. GMII-to-RGMII). 390 */ 391 static int stmmac_of_get_mac_mode(struct device_node *np) 392 { 393 const char *pm; 394 int err, i; 395 396 err = of_property_read_string(np, "mac-mode", &pm); 397 if (err < 0) 398 return err; 399 400 for (i = 0; i < PHY_INTERFACE_MODE_MAX; i++) { 401 if (!strcasecmp(pm, phy_modes(i))) 402 return i; 403 } 404 405 return -ENODEV; 406 } 407 408 /** 409 * stmmac_remove_config_dt - undo the effects of stmmac_probe_config_dt() 410 * @pdev: platform_device structure 411 * @plat: driver data platform structure 412 * 413 * Release resources claimed by stmmac_probe_config_dt(). 414 */ 415 static void stmmac_remove_config_dt(struct platform_device *pdev, 416 struct plat_stmmacenet_data *plat) 417 { 418 clk_disable_unprepare(plat->stmmac_clk); 419 clk_disable_unprepare(plat->pclk); 420 of_node_put(plat->phy_node); 421 of_node_put(plat->mdio_node); 422 } 423 424 /** 425 * stmmac_probe_config_dt - parse device-tree driver parameters 426 * @pdev: platform_device structure 427 * @mac: MAC address to use 428 * Description: 429 * this function is to read the driver parameters from device-tree and 430 * set some private fields that will be used by the main at runtime. 431 */ 432 static struct plat_stmmacenet_data * 433 stmmac_probe_config_dt(struct platform_device *pdev, u8 *mac) 434 { 435 struct device_node *np = pdev->dev.of_node; 436 struct plat_stmmacenet_data *plat; 437 struct stmmac_dma_cfg *dma_cfg; 438 int phy_mode; 439 void *ret; 440 int rc; 441 442 plat = devm_kzalloc(&pdev->dev, sizeof(*plat), GFP_KERNEL); 443 if (!plat) 444 return ERR_PTR(-ENOMEM); 445 446 rc = of_get_mac_address(np, mac); 447 if (rc) { 448 if (rc == -EPROBE_DEFER) 449 return ERR_PTR(rc); 450 451 eth_zero_addr(mac); 452 } 453 454 phy_mode = device_get_phy_mode(&pdev->dev); 455 if (phy_mode < 0) 456 return ERR_PTR(phy_mode); 457 458 plat->phy_interface = phy_mode; 459 rc = stmmac_of_get_mac_mode(np); 460 plat->mac_interface = rc < 0 ? plat->phy_interface : rc; 461 462 /* Some wrapper drivers still rely on phy_node. Let's save it while 463 * they are not converted to phylink. */ 464 plat->phy_node = of_parse_phandle(np, "phy-handle", 0); 465 466 /* PHYLINK automatically parses the phy-handle property */ 467 plat->port_node = of_fwnode_handle(np); 468 469 /* Get max speed of operation from device tree */ 470 of_property_read_u32(np, "max-speed", &plat->max_speed); 471 472 plat->bus_id = of_alias_get_id(np, "ethernet"); 473 if (plat->bus_id < 0) 474 plat->bus_id = 0; 475 476 /* Default to phy auto-detection */ 477 plat->phy_addr = -1; 478 479 /* Default to get clk_csr from stmmac_clk_csr_set(), 480 * or get clk_csr from device tree. 481 */ 482 plat->clk_csr = -1; 483 if (of_property_read_u32(np, "snps,clk-csr", &plat->clk_csr)) 484 of_property_read_u32(np, "clk_csr", &plat->clk_csr); 485 486 /* "snps,phy-addr" is not a standard property. Mark it as deprecated 487 * and warn of its use. Remove this when phy node support is added. 488 */ 489 if (of_property_read_u32(np, "snps,phy-addr", &plat->phy_addr) == 0) 490 dev_warn(&pdev->dev, "snps,phy-addr property is deprecated\n"); 491 492 rc = stmmac_mdio_setup(plat, np, &pdev->dev); 493 if (rc) 494 return ERR_PTR(rc); 495 496 of_property_read_u32(np, "tx-fifo-depth", &plat->tx_fifo_size); 497 498 of_property_read_u32(np, "rx-fifo-depth", &plat->rx_fifo_size); 499 500 plat->force_sf_dma_mode = 501 of_property_read_bool(np, "snps,force_sf_dma_mode"); 502 503 if (of_property_read_bool(np, "snps,en-tx-lpi-clockgating")) 504 plat->flags |= STMMAC_FLAG_EN_TX_LPI_CLOCKGATING; 505 506 /* Set the maxmtu to a default of JUMBO_LEN in case the 507 * parameter is not present in the device tree. 508 */ 509 plat->maxmtu = JUMBO_LEN; 510 511 /* Set default value for multicast hash bins */ 512 plat->multicast_filter_bins = HASH_TABLE_SIZE; 513 514 /* Set default value for unicast filter entries */ 515 plat->unicast_filter_entries = 1; 516 517 /* 518 * Currently only the properties needed on SPEAr600 519 * are provided. All other properties should be added 520 * once needed on other platforms. 521 */ 522 if (of_device_is_compatible(np, "st,spear600-gmac") || 523 of_device_is_compatible(np, "snps,dwmac-3.50a") || 524 of_device_is_compatible(np, "snps,dwmac-3.70a") || 525 of_device_is_compatible(np, "snps,dwmac-3.72a") || 526 of_device_is_compatible(np, "snps,dwmac")) { 527 /* Note that the max-frame-size parameter as defined in the 528 * ePAPR v1.1 spec is defined as max-frame-size, it's 529 * actually used as the IEEE definition of MAC Client 530 * data, or MTU. The ePAPR specification is confusing as 531 * the definition is max-frame-size, but usage examples 532 * are clearly MTUs 533 */ 534 of_property_read_u32(np, "max-frame-size", &plat->maxmtu); 535 of_property_read_u32(np, "snps,multicast-filter-bins", 536 &plat->multicast_filter_bins); 537 of_property_read_u32(np, "snps,perfect-filter-entries", 538 &plat->unicast_filter_entries); 539 plat->unicast_filter_entries = dwmac1000_validate_ucast_entries( 540 &pdev->dev, plat->unicast_filter_entries); 541 plat->multicast_filter_bins = dwmac1000_validate_mcast_bins( 542 &pdev->dev, plat->multicast_filter_bins); 543 plat->has_gmac = 1; 544 plat->pmt = 1; 545 } 546 547 if (of_device_is_compatible(np, "snps,dwmac-3.40a")) { 548 plat->has_gmac = 1; 549 plat->enh_desc = 1; 550 plat->tx_coe = 1; 551 plat->bugged_jumbo = 1; 552 plat->pmt = 1; 553 } 554 555 if (of_device_is_compatible(np, "snps,dwmac-4.00") || 556 of_device_is_compatible(np, "snps,dwmac-4.10a") || 557 of_device_is_compatible(np, "snps,dwmac-4.20a") || 558 of_device_is_compatible(np, "snps,dwmac-5.10a") || 559 of_device_is_compatible(np, "snps,dwmac-5.20")) { 560 plat->has_gmac4 = 1; 561 plat->has_gmac = 0; 562 plat->pmt = 1; 563 if (of_property_read_bool(np, "snps,tso")) 564 plat->flags |= STMMAC_FLAG_TSO_EN; 565 } 566 567 if (of_device_is_compatible(np, "snps,dwmac-3.610") || 568 of_device_is_compatible(np, "snps,dwmac-3.710")) { 569 plat->enh_desc = 1; 570 plat->bugged_jumbo = 1; 571 plat->force_sf_dma_mode = 1; 572 } 573 574 if (of_device_is_compatible(np, "snps,dwxgmac")) { 575 plat->has_xgmac = 1; 576 plat->pmt = 1; 577 if (of_property_read_bool(np, "snps,tso")) 578 plat->flags |= STMMAC_FLAG_TSO_EN; 579 } 580 581 dma_cfg = devm_kzalloc(&pdev->dev, sizeof(*dma_cfg), 582 GFP_KERNEL); 583 if (!dma_cfg) { 584 stmmac_remove_config_dt(pdev, plat); 585 return ERR_PTR(-ENOMEM); 586 } 587 plat->dma_cfg = dma_cfg; 588 589 of_property_read_u32(np, "snps,pbl", &dma_cfg->pbl); 590 if (!dma_cfg->pbl) 591 dma_cfg->pbl = DEFAULT_DMA_PBL; 592 of_property_read_u32(np, "snps,txpbl", &dma_cfg->txpbl); 593 of_property_read_u32(np, "snps,rxpbl", &dma_cfg->rxpbl); 594 dma_cfg->pblx8 = !of_property_read_bool(np, "snps,no-pbl-x8"); 595 596 dma_cfg->aal = of_property_read_bool(np, "snps,aal"); 597 dma_cfg->fixed_burst = of_property_read_bool(np, "snps,fixed-burst"); 598 dma_cfg->mixed_burst = of_property_read_bool(np, "snps,mixed-burst"); 599 600 plat->force_thresh_dma_mode = of_property_read_bool(np, "snps,force_thresh_dma_mode"); 601 if (plat->force_thresh_dma_mode && plat->force_sf_dma_mode) { 602 plat->force_sf_dma_mode = 0; 603 dev_warn(&pdev->dev, 604 "force_sf_dma_mode is ignored if force_thresh_dma_mode is set.\n"); 605 } 606 607 of_property_read_u32(np, "snps,ps-speed", &plat->mac_port_sel_speed); 608 609 plat->axi = stmmac_axi_setup(pdev); 610 611 rc = stmmac_mtl_setup(pdev, plat); 612 if (rc) { 613 stmmac_remove_config_dt(pdev, plat); 614 return ERR_PTR(rc); 615 } 616 617 /* clock setup */ 618 if (!of_device_is_compatible(np, "snps,dwc-qos-ethernet-4.10")) { 619 plat->stmmac_clk = devm_clk_get(&pdev->dev, 620 STMMAC_RESOURCE_NAME); 621 if (IS_ERR(plat->stmmac_clk)) { 622 dev_warn(&pdev->dev, "Cannot get CSR clock\n"); 623 plat->stmmac_clk = NULL; 624 } 625 clk_prepare_enable(plat->stmmac_clk); 626 } 627 628 plat->pclk = devm_clk_get_optional(&pdev->dev, "pclk"); 629 if (IS_ERR(plat->pclk)) { 630 ret = plat->pclk; 631 goto error_pclk_get; 632 } 633 clk_prepare_enable(plat->pclk); 634 635 /* Fall-back to main clock in case of no PTP ref is passed */ 636 plat->clk_ptp_ref = devm_clk_get(&pdev->dev, "ptp_ref"); 637 if (IS_ERR(plat->clk_ptp_ref)) { 638 plat->clk_ptp_rate = clk_get_rate(plat->stmmac_clk); 639 plat->clk_ptp_ref = NULL; 640 dev_info(&pdev->dev, "PTP uses main clock\n"); 641 } else { 642 plat->clk_ptp_rate = clk_get_rate(plat->clk_ptp_ref); 643 dev_dbg(&pdev->dev, "PTP rate %d\n", plat->clk_ptp_rate); 644 } 645 646 plat->stmmac_rst = devm_reset_control_get_optional(&pdev->dev, 647 STMMAC_RESOURCE_NAME); 648 if (IS_ERR(plat->stmmac_rst)) { 649 ret = plat->stmmac_rst; 650 goto error_hw_init; 651 } 652 653 plat->stmmac_ahb_rst = devm_reset_control_get_optional_shared( 654 &pdev->dev, "ahb"); 655 if (IS_ERR(plat->stmmac_ahb_rst)) { 656 ret = plat->stmmac_ahb_rst; 657 goto error_hw_init; 658 } 659 660 return plat; 661 662 error_hw_init: 663 clk_disable_unprepare(plat->pclk); 664 error_pclk_get: 665 clk_disable_unprepare(plat->stmmac_clk); 666 667 return ret; 668 } 669 670 static void devm_stmmac_remove_config_dt(void *data) 671 { 672 struct plat_stmmacenet_data *plat = data; 673 674 /* Platform data argument is unused */ 675 stmmac_remove_config_dt(NULL, plat); 676 } 677 678 /** 679 * devm_stmmac_probe_config_dt 680 * @pdev: platform_device structure 681 * @mac: MAC address to use 682 * Description: Devres variant of stmmac_probe_config_dt(). Does not require 683 * the user to call stmmac_remove_config_dt() at driver detach. 684 */ 685 struct plat_stmmacenet_data * 686 devm_stmmac_probe_config_dt(struct platform_device *pdev, u8 *mac) 687 { 688 struct plat_stmmacenet_data *plat; 689 int ret; 690 691 plat = stmmac_probe_config_dt(pdev, mac); 692 if (IS_ERR(plat)) 693 return plat; 694 695 ret = devm_add_action_or_reset(&pdev->dev, 696 devm_stmmac_remove_config_dt, plat); 697 if (ret) 698 return ERR_PTR(ret); 699 700 return plat; 701 } 702 #else 703 struct plat_stmmacenet_data * 704 devm_stmmac_probe_config_dt(struct platform_device *pdev, u8 *mac) 705 { 706 return ERR_PTR(-EINVAL); 707 } 708 #endif /* CONFIG_OF */ 709 EXPORT_SYMBOL_GPL(devm_stmmac_probe_config_dt); 710 711 int stmmac_get_platform_resources(struct platform_device *pdev, 712 struct stmmac_resources *stmmac_res) 713 { 714 memset(stmmac_res, 0, sizeof(*stmmac_res)); 715 716 /* Get IRQ information early to have an ability to ask for deferred 717 * probe if needed before we went too far with resource allocation. 718 */ 719 stmmac_res->irq = platform_get_irq_byname(pdev, "macirq"); 720 if (stmmac_res->irq < 0) 721 return stmmac_res->irq; 722 723 /* On some platforms e.g. SPEAr the wake up irq differs from the mac irq 724 * The external wake up irq can be passed through the platform code 725 * named as "eth_wake_irq" 726 * 727 * In case the wake up interrupt is not passed from the platform 728 * so the driver will continue to use the mac irq (ndev->irq) 729 */ 730 stmmac_res->wol_irq = 731 platform_get_irq_byname_optional(pdev, "eth_wake_irq"); 732 if (stmmac_res->wol_irq < 0) { 733 if (stmmac_res->wol_irq == -EPROBE_DEFER) 734 return -EPROBE_DEFER; 735 dev_info(&pdev->dev, "IRQ eth_wake_irq not found\n"); 736 stmmac_res->wol_irq = stmmac_res->irq; 737 } 738 739 stmmac_res->lpi_irq = 740 platform_get_irq_byname_optional(pdev, "eth_lpi"); 741 if (stmmac_res->lpi_irq < 0) { 742 if (stmmac_res->lpi_irq == -EPROBE_DEFER) 743 return -EPROBE_DEFER; 744 dev_info(&pdev->dev, "IRQ eth_lpi not found\n"); 745 } 746 747 stmmac_res->sfty_irq = 748 platform_get_irq_byname_optional(pdev, "sfty"); 749 if (stmmac_res->sfty_irq < 0) { 750 if (stmmac_res->sfty_irq == -EPROBE_DEFER) 751 return -EPROBE_DEFER; 752 dev_info(&pdev->dev, "IRQ sfty not found\n"); 753 } 754 755 stmmac_res->addr = devm_platform_ioremap_resource(pdev, 0); 756 757 return PTR_ERR_OR_ZERO(stmmac_res->addr); 758 } 759 EXPORT_SYMBOL_GPL(stmmac_get_platform_resources); 760 761 /** 762 * stmmac_pltfr_init 763 * @pdev: pointer to the platform device 764 * @plat: driver data platform structure 765 * Description: Call the platform's init callback (if any) and propagate 766 * the return value. 767 */ 768 static int stmmac_pltfr_init(struct platform_device *pdev, 769 struct plat_stmmacenet_data *plat) 770 { 771 int ret = 0; 772 773 if (plat->init) 774 ret = plat->init(pdev, plat->bsp_priv); 775 776 return ret; 777 } 778 779 /** 780 * stmmac_pltfr_exit 781 * @pdev: pointer to the platform device 782 * @plat: driver data platform structure 783 * Description: Call the platform's exit callback (if any). 784 */ 785 static void stmmac_pltfr_exit(struct platform_device *pdev, 786 struct plat_stmmacenet_data *plat) 787 { 788 if (plat->exit) 789 plat->exit(pdev, plat->bsp_priv); 790 } 791 792 /** 793 * stmmac_pltfr_probe 794 * @pdev: platform device pointer 795 * @plat: driver data platform structure 796 * @res: stmmac resources structure 797 * Description: This calls the platform's init() callback and probes the 798 * stmmac driver. 799 */ 800 int stmmac_pltfr_probe(struct platform_device *pdev, 801 struct plat_stmmacenet_data *plat, 802 struct stmmac_resources *res) 803 { 804 int ret; 805 806 ret = stmmac_pltfr_init(pdev, plat); 807 if (ret) 808 return ret; 809 810 ret = stmmac_dvr_probe(&pdev->dev, plat, res); 811 if (ret) { 812 stmmac_pltfr_exit(pdev, plat); 813 return ret; 814 } 815 816 return ret; 817 } 818 EXPORT_SYMBOL_GPL(stmmac_pltfr_probe); 819 820 static void devm_stmmac_pltfr_remove(void *data) 821 { 822 struct platform_device *pdev = data; 823 824 stmmac_pltfr_remove(pdev); 825 } 826 827 /** 828 * devm_stmmac_pltfr_probe 829 * @pdev: pointer to the platform device 830 * @plat: driver data platform structure 831 * @res: stmmac resources 832 * Description: Devres variant of stmmac_pltfr_probe(). Allows users to skip 833 * calling stmmac_pltfr_remove() on driver detach. 834 */ 835 int devm_stmmac_pltfr_probe(struct platform_device *pdev, 836 struct plat_stmmacenet_data *plat, 837 struct stmmac_resources *res) 838 { 839 int ret; 840 841 ret = stmmac_pltfr_probe(pdev, plat, res); 842 if (ret) 843 return ret; 844 845 return devm_add_action_or_reset(&pdev->dev, devm_stmmac_pltfr_remove, 846 pdev); 847 } 848 EXPORT_SYMBOL_GPL(devm_stmmac_pltfr_probe); 849 850 /** 851 * stmmac_pltfr_remove 852 * @pdev: pointer to the platform device 853 * Description: This undoes the effects of stmmac_pltfr_probe() by removing the 854 * driver and calling the platform's exit() callback. 855 */ 856 void stmmac_pltfr_remove(struct platform_device *pdev) 857 { 858 struct net_device *ndev = platform_get_drvdata(pdev); 859 struct stmmac_priv *priv = netdev_priv(ndev); 860 struct plat_stmmacenet_data *plat = priv->plat; 861 862 stmmac_dvr_remove(&pdev->dev); 863 stmmac_pltfr_exit(pdev, plat); 864 } 865 EXPORT_SYMBOL_GPL(stmmac_pltfr_remove); 866 867 /** 868 * stmmac_pltfr_suspend 869 * @dev: device pointer 870 * Description: this function is invoked when suspend the driver and it direcly 871 * call the main suspend function and then, if required, on some platform, it 872 * can call an exit helper. 873 */ 874 static int __maybe_unused stmmac_pltfr_suspend(struct device *dev) 875 { 876 int ret; 877 struct net_device *ndev = dev_get_drvdata(dev); 878 struct stmmac_priv *priv = netdev_priv(ndev); 879 struct platform_device *pdev = to_platform_device(dev); 880 881 ret = stmmac_suspend(dev); 882 stmmac_pltfr_exit(pdev, priv->plat); 883 884 return ret; 885 } 886 887 /** 888 * stmmac_pltfr_resume 889 * @dev: device pointer 890 * Description: this function is invoked when resume the driver before calling 891 * the main resume function, on some platforms, it can call own init helper 892 * if required. 893 */ 894 static int __maybe_unused stmmac_pltfr_resume(struct device *dev) 895 { 896 struct net_device *ndev = dev_get_drvdata(dev); 897 struct stmmac_priv *priv = netdev_priv(ndev); 898 struct platform_device *pdev = to_platform_device(dev); 899 int ret; 900 901 ret = stmmac_pltfr_init(pdev, priv->plat); 902 if (ret) 903 return ret; 904 905 return stmmac_resume(dev); 906 } 907 908 static int __maybe_unused stmmac_runtime_suspend(struct device *dev) 909 { 910 struct net_device *ndev = dev_get_drvdata(dev); 911 struct stmmac_priv *priv = netdev_priv(ndev); 912 913 stmmac_bus_clks_config(priv, false); 914 915 return 0; 916 } 917 918 static int __maybe_unused stmmac_runtime_resume(struct device *dev) 919 { 920 struct net_device *ndev = dev_get_drvdata(dev); 921 struct stmmac_priv *priv = netdev_priv(ndev); 922 923 return stmmac_bus_clks_config(priv, true); 924 } 925 926 static int __maybe_unused stmmac_pltfr_noirq_suspend(struct device *dev) 927 { 928 struct net_device *ndev = dev_get_drvdata(dev); 929 struct stmmac_priv *priv = netdev_priv(ndev); 930 int ret; 931 932 if (!netif_running(ndev)) 933 return 0; 934 935 if (!device_may_wakeup(priv->device) || !priv->plat->pmt) { 936 /* Disable clock in case of PWM is off */ 937 clk_disable_unprepare(priv->plat->clk_ptp_ref); 938 939 ret = pm_runtime_force_suspend(dev); 940 if (ret) 941 return ret; 942 } 943 944 return 0; 945 } 946 947 static int __maybe_unused stmmac_pltfr_noirq_resume(struct device *dev) 948 { 949 struct net_device *ndev = dev_get_drvdata(dev); 950 struct stmmac_priv *priv = netdev_priv(ndev); 951 int ret; 952 953 if (!netif_running(ndev)) 954 return 0; 955 956 if (!device_may_wakeup(priv->device) || !priv->plat->pmt) { 957 /* enable the clk previously disabled */ 958 ret = pm_runtime_force_resume(dev); 959 if (ret) 960 return ret; 961 962 ret = clk_prepare_enable(priv->plat->clk_ptp_ref); 963 if (ret < 0) { 964 netdev_warn(priv->dev, 965 "failed to enable PTP reference clock: %pe\n", 966 ERR_PTR(ret)); 967 return ret; 968 } 969 } 970 971 return 0; 972 } 973 974 const struct dev_pm_ops stmmac_pltfr_pm_ops = { 975 SET_SYSTEM_SLEEP_PM_OPS(stmmac_pltfr_suspend, stmmac_pltfr_resume) 976 SET_RUNTIME_PM_OPS(stmmac_runtime_suspend, stmmac_runtime_resume, NULL) 977 SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(stmmac_pltfr_noirq_suspend, stmmac_pltfr_noirq_resume) 978 }; 979 EXPORT_SYMBOL_GPL(stmmac_pltfr_pm_ops); 980 981 MODULE_DESCRIPTION("STMMAC 10/100/1000 Ethernet platform support"); 982 MODULE_AUTHOR("Giuseppe Cavallaro <peppe.cavallaro@st.com>"); 983 MODULE_LICENSE("GPL"); 984