1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * dwmac-sun8i.c - Allwinner sun8i DWMAC specific glue layer 4 * 5 * Copyright (C) 2017 Corentin Labbe <clabbe.montjoie@gmail.com> 6 */ 7 8 #include <linux/clk.h> 9 #include <linux/io.h> 10 #include <linux/iopoll.h> 11 #include <linux/mdio-mux.h> 12 #include <linux/mfd/syscon.h> 13 #include <linux/module.h> 14 #include <linux/of.h> 15 #include <linux/of_mdio.h> 16 #include <linux/of_net.h> 17 #include <linux/of_platform.h> 18 #include <linux/phy.h> 19 #include <linux/platform_device.h> 20 #include <linux/pm_runtime.h> 21 #include <linux/regulator/consumer.h> 22 #include <linux/regmap.h> 23 #include <linux/stmmac.h> 24 25 #include "stmmac.h" 26 #include "stmmac_platform.h" 27 28 /* General notes on dwmac-sun8i: 29 * Locking: no locking is necessary in this file because all necessary locking 30 * is done in the "stmmac files" 31 */ 32 33 /* struct emac_variant - Describe dwmac-sun8i hardware variant 34 * @default_syscon_value: The default value of the EMAC register in syscon 35 * This value is used for disabling properly EMAC 36 * and used as a good starting value in case of the 37 * boot process(uboot) leave some stuff. 38 * @syscon_field reg_field for the syscon's gmac register 39 * @soc_has_internal_phy: Does the MAC embed an internal PHY 40 * @support_mii: Does the MAC handle MII 41 * @support_rmii: Does the MAC handle RMII 42 * @support_rgmii: Does the MAC handle RGMII 43 * 44 * @rx_delay_max: Maximum raw value for RX delay chain 45 * @tx_delay_max: Maximum raw value for TX delay chain 46 * These two also indicate the bitmask for 47 * the RX and TX delay chain registers. A 48 * value of zero indicates this is not supported. 49 */ 50 struct emac_variant { 51 u32 default_syscon_value; 52 const struct reg_field *syscon_field; 53 bool soc_has_internal_phy; 54 bool support_mii; 55 bool support_rmii; 56 bool support_rgmii; 57 u8 rx_delay_max; 58 u8 tx_delay_max; 59 }; 60 61 /* struct sunxi_priv_data - hold all sunxi private data 62 * @ephy_clk: reference to the optional EPHY clock for the internal PHY 63 * @regulator: reference to the optional regulator 64 * @rst_ephy: reference to the optional EPHY reset for the internal PHY 65 * @variant: reference to the current board variant 66 * @regmap: regmap for using the syscon 67 * @internal_phy_powered: Does the internal PHY is enabled 68 * @use_internal_phy: Is the internal PHY selected for use 69 * @mux_handle: Internal pointer used by mdio-mux lib 70 */ 71 struct sunxi_priv_data { 72 struct clk *ephy_clk; 73 struct regulator *regulator; 74 struct reset_control *rst_ephy; 75 const struct emac_variant *variant; 76 struct regmap_field *regmap_field; 77 bool internal_phy_powered; 78 bool use_internal_phy; 79 void *mux_handle; 80 }; 81 82 /* EMAC clock register @ 0x30 in the "system control" address range */ 83 static const struct reg_field sun8i_syscon_reg_field = { 84 .reg = 0x30, 85 .lsb = 0, 86 .msb = 31, 87 }; 88 89 /* EMAC clock register @ 0x164 in the CCU address range */ 90 static const struct reg_field sun8i_ccu_reg_field = { 91 .reg = 0x164, 92 .lsb = 0, 93 .msb = 31, 94 }; 95 96 static const struct emac_variant emac_variant_h3 = { 97 .default_syscon_value = 0x58000, 98 .syscon_field = &sun8i_syscon_reg_field, 99 .soc_has_internal_phy = true, 100 .support_mii = true, 101 .support_rmii = true, 102 .support_rgmii = true, 103 .rx_delay_max = 31, 104 .tx_delay_max = 7, 105 }; 106 107 static const struct emac_variant emac_variant_v3s = { 108 .default_syscon_value = 0x38000, 109 .syscon_field = &sun8i_syscon_reg_field, 110 .soc_has_internal_phy = true, 111 .support_mii = true 112 }; 113 114 static const struct emac_variant emac_variant_a83t = { 115 .default_syscon_value = 0, 116 .syscon_field = &sun8i_syscon_reg_field, 117 .soc_has_internal_phy = false, 118 .support_mii = true, 119 .support_rgmii = true, 120 .rx_delay_max = 31, 121 .tx_delay_max = 7, 122 }; 123 124 static const struct emac_variant emac_variant_r40 = { 125 .default_syscon_value = 0, 126 .syscon_field = &sun8i_ccu_reg_field, 127 .support_mii = true, 128 .support_rgmii = true, 129 .rx_delay_max = 7, 130 }; 131 132 static const struct emac_variant emac_variant_a64 = { 133 .default_syscon_value = 0, 134 .syscon_field = &sun8i_syscon_reg_field, 135 .soc_has_internal_phy = false, 136 .support_mii = true, 137 .support_rmii = true, 138 .support_rgmii = true, 139 .rx_delay_max = 31, 140 .tx_delay_max = 7, 141 }; 142 143 static const struct emac_variant emac_variant_h6 = { 144 .default_syscon_value = 0x50000, 145 .syscon_field = &sun8i_syscon_reg_field, 146 /* The "Internal PHY" of H6 is not on the die. It's on the 147 * co-packaged AC200 chip instead. 148 */ 149 .soc_has_internal_phy = false, 150 .support_mii = true, 151 .support_rmii = true, 152 .support_rgmii = true, 153 .rx_delay_max = 31, 154 .tx_delay_max = 7, 155 }; 156 157 #define EMAC_BASIC_CTL0 0x00 158 #define EMAC_BASIC_CTL1 0x04 159 #define EMAC_INT_STA 0x08 160 #define EMAC_INT_EN 0x0C 161 #define EMAC_TX_CTL0 0x10 162 #define EMAC_TX_CTL1 0x14 163 #define EMAC_TX_FLOW_CTL 0x1C 164 #define EMAC_TX_DESC_LIST 0x20 165 #define EMAC_RX_CTL0 0x24 166 #define EMAC_RX_CTL1 0x28 167 #define EMAC_RX_DESC_LIST 0x34 168 #define EMAC_RX_FRM_FLT 0x38 169 #define EMAC_MDIO_CMD 0x48 170 #define EMAC_MDIO_DATA 0x4C 171 #define EMAC_MACADDR_HI(reg) (0x50 + (reg) * 8) 172 #define EMAC_MACADDR_LO(reg) (0x54 + (reg) * 8) 173 #define EMAC_TX_DMA_STA 0xB0 174 #define EMAC_TX_CUR_DESC 0xB4 175 #define EMAC_TX_CUR_BUF 0xB8 176 #define EMAC_RX_DMA_STA 0xC0 177 #define EMAC_RX_CUR_DESC 0xC4 178 #define EMAC_RX_CUR_BUF 0xC8 179 180 /* Use in EMAC_BASIC_CTL0 */ 181 #define EMAC_DUPLEX_FULL BIT(0) 182 #define EMAC_LOOPBACK BIT(1) 183 #define EMAC_SPEED_1000 0 184 #define EMAC_SPEED_100 (0x03 << 2) 185 #define EMAC_SPEED_10 (0x02 << 2) 186 187 /* Use in EMAC_BASIC_CTL1 */ 188 #define EMAC_BURSTLEN_SHIFT 24 189 190 /* Used in EMAC_RX_FRM_FLT */ 191 #define EMAC_FRM_FLT_RXALL BIT(0) 192 #define EMAC_FRM_FLT_CTL BIT(13) 193 #define EMAC_FRM_FLT_MULTICAST BIT(16) 194 195 /* Used in RX_CTL1*/ 196 #define EMAC_RX_MD BIT(1) 197 #define EMAC_RX_TH_MASK GENMASK(5, 4) 198 #define EMAC_RX_TH_32 0 199 #define EMAC_RX_TH_64 (0x1 << 4) 200 #define EMAC_RX_TH_96 (0x2 << 4) 201 #define EMAC_RX_TH_128 (0x3 << 4) 202 #define EMAC_RX_DMA_EN BIT(30) 203 #define EMAC_RX_DMA_START BIT(31) 204 205 /* Used in TX_CTL1*/ 206 #define EMAC_TX_MD BIT(1) 207 #define EMAC_TX_NEXT_FRM BIT(2) 208 #define EMAC_TX_TH_MASK GENMASK(10, 8) 209 #define EMAC_TX_TH_64 0 210 #define EMAC_TX_TH_128 (0x1 << 8) 211 #define EMAC_TX_TH_192 (0x2 << 8) 212 #define EMAC_TX_TH_256 (0x3 << 8) 213 #define EMAC_TX_DMA_EN BIT(30) 214 #define EMAC_TX_DMA_START BIT(31) 215 216 /* Used in RX_CTL0 */ 217 #define EMAC_RX_RECEIVER_EN BIT(31) 218 #define EMAC_RX_DO_CRC BIT(27) 219 #define EMAC_RX_FLOW_CTL_EN BIT(16) 220 221 /* Used in TX_CTL0 */ 222 #define EMAC_TX_TRANSMITTER_EN BIT(31) 223 224 /* Used in EMAC_TX_FLOW_CTL */ 225 #define EMAC_TX_FLOW_CTL_EN BIT(0) 226 227 /* Used in EMAC_INT_STA */ 228 #define EMAC_TX_INT BIT(0) 229 #define EMAC_TX_DMA_STOP_INT BIT(1) 230 #define EMAC_TX_BUF_UA_INT BIT(2) 231 #define EMAC_TX_TIMEOUT_INT BIT(3) 232 #define EMAC_TX_UNDERFLOW_INT BIT(4) 233 #define EMAC_TX_EARLY_INT BIT(5) 234 #define EMAC_RX_INT BIT(8) 235 #define EMAC_RX_BUF_UA_INT BIT(9) 236 #define EMAC_RX_DMA_STOP_INT BIT(10) 237 #define EMAC_RX_TIMEOUT_INT BIT(11) 238 #define EMAC_RX_OVERFLOW_INT BIT(12) 239 #define EMAC_RX_EARLY_INT BIT(13) 240 #define EMAC_RGMII_STA_INT BIT(16) 241 242 #define EMAC_INT_MSK_COMMON EMAC_RGMII_STA_INT 243 #define EMAC_INT_MSK_TX (EMAC_TX_INT | \ 244 EMAC_TX_DMA_STOP_INT | \ 245 EMAC_TX_BUF_UA_INT | \ 246 EMAC_TX_TIMEOUT_INT | \ 247 EMAC_TX_UNDERFLOW_INT | \ 248 EMAC_TX_EARLY_INT |\ 249 EMAC_INT_MSK_COMMON) 250 #define EMAC_INT_MSK_RX (EMAC_RX_INT | \ 251 EMAC_RX_BUF_UA_INT | \ 252 EMAC_RX_DMA_STOP_INT | \ 253 EMAC_RX_TIMEOUT_INT | \ 254 EMAC_RX_OVERFLOW_INT | \ 255 EMAC_RX_EARLY_INT | \ 256 EMAC_INT_MSK_COMMON) 257 258 #define MAC_ADDR_TYPE_DST BIT(31) 259 260 /* H3 specific bits for EPHY */ 261 #define H3_EPHY_ADDR_SHIFT 20 262 #define H3_EPHY_CLK_SEL BIT(18) /* 1: 24MHz, 0: 25MHz */ 263 #define H3_EPHY_LED_POL BIT(17) /* 1: active low, 0: active high */ 264 #define H3_EPHY_SHUTDOWN BIT(16) /* 1: shutdown, 0: power up */ 265 #define H3_EPHY_SELECT BIT(15) /* 1: internal PHY, 0: external PHY */ 266 #define H3_EPHY_MUX_MASK (H3_EPHY_SHUTDOWN | H3_EPHY_SELECT) 267 #define DWMAC_SUN8I_MDIO_MUX_INTERNAL_ID 1 268 #define DWMAC_SUN8I_MDIO_MUX_EXTERNAL_ID 2 269 270 /* H3/A64 specific bits */ 271 #define SYSCON_RMII_EN BIT(13) /* 1: enable RMII (overrides EPIT) */ 272 273 /* Generic system control EMAC_CLK bits */ 274 #define SYSCON_ETXDC_SHIFT 10 275 #define SYSCON_ERXDC_SHIFT 5 276 /* EMAC PHY Interface Type */ 277 #define SYSCON_EPIT BIT(2) /* 1: RGMII, 0: MII */ 278 #define SYSCON_ETCS_MASK GENMASK(1, 0) 279 #define SYSCON_ETCS_MII 0x0 280 #define SYSCON_ETCS_EXT_GMII 0x1 281 #define SYSCON_ETCS_INT_GMII 0x2 282 283 /* sun8i_dwmac_dma_reset() - reset the EMAC 284 * Called from stmmac via stmmac_dma_ops->reset 285 */ 286 static int sun8i_dwmac_dma_reset(void __iomem *ioaddr) 287 { 288 writel(0, ioaddr + EMAC_RX_CTL1); 289 writel(0, ioaddr + EMAC_TX_CTL1); 290 writel(0, ioaddr + EMAC_RX_FRM_FLT); 291 writel(0, ioaddr + EMAC_RX_DESC_LIST); 292 writel(0, ioaddr + EMAC_TX_DESC_LIST); 293 writel(0, ioaddr + EMAC_INT_EN); 294 writel(0x1FFFFFF, ioaddr + EMAC_INT_STA); 295 return 0; 296 } 297 298 /* sun8i_dwmac_dma_init() - initialize the EMAC 299 * Called from stmmac via stmmac_dma_ops->init 300 */ 301 static void sun8i_dwmac_dma_init(void __iomem *ioaddr, 302 struct stmmac_dma_cfg *dma_cfg) 303 { 304 writel(EMAC_RX_INT | EMAC_TX_INT, ioaddr + EMAC_INT_EN); 305 writel(0x1FFFFFF, ioaddr + EMAC_INT_STA); 306 } 307 308 static void sun8i_dwmac_dma_init_rx(struct stmmac_priv *priv, 309 void __iomem *ioaddr, 310 struct stmmac_dma_cfg *dma_cfg, 311 dma_addr_t dma_rx_phy, u32 chan) 312 { 313 /* Write RX descriptors address */ 314 writel(lower_32_bits(dma_rx_phy), ioaddr + EMAC_RX_DESC_LIST); 315 } 316 317 static void sun8i_dwmac_dma_init_tx(struct stmmac_priv *priv, 318 void __iomem *ioaddr, 319 struct stmmac_dma_cfg *dma_cfg, 320 dma_addr_t dma_tx_phy, u32 chan) 321 { 322 /* Write TX descriptors address */ 323 writel(lower_32_bits(dma_tx_phy), ioaddr + EMAC_TX_DESC_LIST); 324 } 325 326 /* sun8i_dwmac_dump_regs() - Dump EMAC address space 327 * Called from stmmac_dma_ops->dump_regs 328 * Used for ethtool 329 */ 330 static void sun8i_dwmac_dump_regs(struct stmmac_priv *priv, 331 void __iomem *ioaddr, u32 *reg_space) 332 { 333 int i; 334 335 for (i = 0; i < 0xC8; i += 4) { 336 if (i == 0x32 || i == 0x3C) 337 continue; 338 reg_space[i / 4] = readl(ioaddr + i); 339 } 340 } 341 342 /* sun8i_dwmac_dump_mac_regs() - Dump EMAC address space 343 * Called from stmmac_ops->dump_regs 344 * Used for ethtool 345 */ 346 static void sun8i_dwmac_dump_mac_regs(struct mac_device_info *hw, 347 u32 *reg_space) 348 { 349 int i; 350 void __iomem *ioaddr = hw->pcsr; 351 352 for (i = 0; i < 0xC8; i += 4) { 353 if (i == 0x32 || i == 0x3C) 354 continue; 355 reg_space[i / 4] = readl(ioaddr + i); 356 } 357 } 358 359 static void sun8i_dwmac_enable_dma_irq(struct stmmac_priv *priv, 360 void __iomem *ioaddr, u32 chan, 361 bool rx, bool tx) 362 { 363 u32 value = readl(ioaddr + EMAC_INT_EN); 364 365 if (rx) 366 value |= EMAC_RX_INT; 367 if (tx) 368 value |= EMAC_TX_INT; 369 370 writel(value, ioaddr + EMAC_INT_EN); 371 } 372 373 static void sun8i_dwmac_disable_dma_irq(struct stmmac_priv *priv, 374 void __iomem *ioaddr, u32 chan, 375 bool rx, bool tx) 376 { 377 u32 value = readl(ioaddr + EMAC_INT_EN); 378 379 if (rx) 380 value &= ~EMAC_RX_INT; 381 if (tx) 382 value &= ~EMAC_TX_INT; 383 384 writel(value, ioaddr + EMAC_INT_EN); 385 } 386 387 static void sun8i_dwmac_dma_start_tx(struct stmmac_priv *priv, 388 void __iomem *ioaddr, u32 chan) 389 { 390 u32 v; 391 392 v = readl(ioaddr + EMAC_TX_CTL1); 393 v |= EMAC_TX_DMA_START; 394 v |= EMAC_TX_DMA_EN; 395 writel(v, ioaddr + EMAC_TX_CTL1); 396 } 397 398 static void sun8i_dwmac_enable_dma_transmission(void __iomem *ioaddr, u32 chan) 399 { 400 u32 v; 401 402 v = readl(ioaddr + EMAC_TX_CTL1); 403 v |= EMAC_TX_DMA_START; 404 v |= EMAC_TX_DMA_EN; 405 writel(v, ioaddr + EMAC_TX_CTL1); 406 } 407 408 static void sun8i_dwmac_dma_stop_tx(struct stmmac_priv *priv, 409 void __iomem *ioaddr, u32 chan) 410 { 411 u32 v; 412 413 v = readl(ioaddr + EMAC_TX_CTL1); 414 v &= ~EMAC_TX_DMA_EN; 415 writel(v, ioaddr + EMAC_TX_CTL1); 416 } 417 418 static void sun8i_dwmac_dma_start_rx(struct stmmac_priv *priv, 419 void __iomem *ioaddr, u32 chan) 420 { 421 u32 v; 422 423 v = readl(ioaddr + EMAC_RX_CTL1); 424 v |= EMAC_RX_DMA_START; 425 v |= EMAC_RX_DMA_EN; 426 writel(v, ioaddr + EMAC_RX_CTL1); 427 } 428 429 static void sun8i_dwmac_dma_stop_rx(struct stmmac_priv *priv, 430 void __iomem *ioaddr, u32 chan) 431 { 432 u32 v; 433 434 v = readl(ioaddr + EMAC_RX_CTL1); 435 v &= ~EMAC_RX_DMA_EN; 436 writel(v, ioaddr + EMAC_RX_CTL1); 437 } 438 439 static int sun8i_dwmac_dma_interrupt(struct stmmac_priv *priv, 440 void __iomem *ioaddr, 441 struct stmmac_extra_stats *x, u32 chan, 442 u32 dir) 443 { 444 struct stmmac_pcpu_stats *stats = this_cpu_ptr(priv->xstats.pcpu_stats); 445 int ret = 0; 446 u32 v; 447 448 v = readl(ioaddr + EMAC_INT_STA); 449 450 if (dir == DMA_DIR_RX) 451 v &= EMAC_INT_MSK_RX; 452 else if (dir == DMA_DIR_TX) 453 v &= EMAC_INT_MSK_TX; 454 455 if (v & EMAC_TX_INT) { 456 ret |= handle_tx; 457 u64_stats_update_begin(&stats->syncp); 458 u64_stats_inc(&stats->tx_normal_irq_n[chan]); 459 u64_stats_update_end(&stats->syncp); 460 } 461 462 if (v & EMAC_TX_DMA_STOP_INT) 463 x->tx_process_stopped_irq++; 464 465 if (v & EMAC_TX_BUF_UA_INT) 466 x->tx_process_stopped_irq++; 467 468 if (v & EMAC_TX_TIMEOUT_INT) 469 ret |= tx_hard_error; 470 471 if (v & EMAC_TX_UNDERFLOW_INT) { 472 ret |= tx_hard_error; 473 x->tx_undeflow_irq++; 474 } 475 476 if (v & EMAC_TX_EARLY_INT) 477 x->tx_early_irq++; 478 479 if (v & EMAC_RX_INT) { 480 ret |= handle_rx; 481 u64_stats_update_begin(&stats->syncp); 482 u64_stats_inc(&stats->rx_normal_irq_n[chan]); 483 u64_stats_update_end(&stats->syncp); 484 } 485 486 if (v & EMAC_RX_BUF_UA_INT) 487 x->rx_buf_unav_irq++; 488 489 if (v & EMAC_RX_DMA_STOP_INT) 490 x->rx_process_stopped_irq++; 491 492 if (v & EMAC_RX_TIMEOUT_INT) 493 ret |= tx_hard_error; 494 495 if (v & EMAC_RX_OVERFLOW_INT) { 496 ret |= tx_hard_error; 497 x->rx_overflow_irq++; 498 } 499 500 if (v & EMAC_RX_EARLY_INT) 501 x->rx_early_irq++; 502 503 if (v & EMAC_RGMII_STA_INT) 504 x->irq_rgmii_n++; 505 506 writel(v, ioaddr + EMAC_INT_STA); 507 508 return ret; 509 } 510 511 static void sun8i_dwmac_dma_operation_mode_rx(struct stmmac_priv *priv, 512 void __iomem *ioaddr, int mode, 513 u32 channel, int fifosz, u8 qmode) 514 { 515 u32 v; 516 517 v = readl(ioaddr + EMAC_RX_CTL1); 518 if (mode == SF_DMA_MODE) { 519 v |= EMAC_RX_MD; 520 } else { 521 v &= ~EMAC_RX_MD; 522 v &= ~EMAC_RX_TH_MASK; 523 if (mode < 32) 524 v |= EMAC_RX_TH_32; 525 else if (mode < 64) 526 v |= EMAC_RX_TH_64; 527 else if (mode < 96) 528 v |= EMAC_RX_TH_96; 529 else if (mode < 128) 530 v |= EMAC_RX_TH_128; 531 } 532 writel(v, ioaddr + EMAC_RX_CTL1); 533 } 534 535 static void sun8i_dwmac_dma_operation_mode_tx(struct stmmac_priv *priv, 536 void __iomem *ioaddr, int mode, 537 u32 channel, int fifosz, u8 qmode) 538 { 539 u32 v; 540 541 v = readl(ioaddr + EMAC_TX_CTL1); 542 if (mode == SF_DMA_MODE) { 543 v |= EMAC_TX_MD; 544 /* Undocumented bit (called TX_NEXT_FRM in BSP), the original 545 * comment is 546 * "Operating on second frame increase the performance 547 * especially when transmit store-and-forward is used." 548 */ 549 v |= EMAC_TX_NEXT_FRM; 550 } else { 551 v &= ~EMAC_TX_MD; 552 v &= ~EMAC_TX_TH_MASK; 553 if (mode < 64) 554 v |= EMAC_TX_TH_64; 555 else if (mode < 128) 556 v |= EMAC_TX_TH_128; 557 else if (mode < 192) 558 v |= EMAC_TX_TH_192; 559 else if (mode < 256) 560 v |= EMAC_TX_TH_256; 561 } 562 writel(v, ioaddr + EMAC_TX_CTL1); 563 } 564 565 static const struct stmmac_dma_ops sun8i_dwmac_dma_ops = { 566 .reset = sun8i_dwmac_dma_reset, 567 .init = sun8i_dwmac_dma_init, 568 .init_rx_chan = sun8i_dwmac_dma_init_rx, 569 .init_tx_chan = sun8i_dwmac_dma_init_tx, 570 .dump_regs = sun8i_dwmac_dump_regs, 571 .dma_rx_mode = sun8i_dwmac_dma_operation_mode_rx, 572 .dma_tx_mode = sun8i_dwmac_dma_operation_mode_tx, 573 .enable_dma_transmission = sun8i_dwmac_enable_dma_transmission, 574 .enable_dma_irq = sun8i_dwmac_enable_dma_irq, 575 .disable_dma_irq = sun8i_dwmac_disable_dma_irq, 576 .start_tx = sun8i_dwmac_dma_start_tx, 577 .stop_tx = sun8i_dwmac_dma_stop_tx, 578 .start_rx = sun8i_dwmac_dma_start_rx, 579 .stop_rx = sun8i_dwmac_dma_stop_rx, 580 .dma_interrupt = sun8i_dwmac_dma_interrupt, 581 }; 582 583 static int sun8i_dwmac_power_internal_phy(struct stmmac_priv *priv); 584 585 static int sun8i_dwmac_init(struct platform_device *pdev, void *priv) 586 { 587 struct net_device *ndev = platform_get_drvdata(pdev); 588 struct sunxi_priv_data *gmac = priv; 589 int ret; 590 591 if (gmac->regulator) { 592 ret = regulator_enable(gmac->regulator); 593 if (ret) { 594 dev_err(&pdev->dev, "Fail to enable regulator\n"); 595 return ret; 596 } 597 } 598 599 if (gmac->use_internal_phy) { 600 ret = sun8i_dwmac_power_internal_phy(netdev_priv(ndev)); 601 if (ret) 602 goto err_disable_regulator; 603 } 604 605 return 0; 606 607 err_disable_regulator: 608 if (gmac->regulator) 609 regulator_disable(gmac->regulator); 610 611 return ret; 612 } 613 614 static void sun8i_dwmac_core_init(struct mac_device_info *hw, 615 struct net_device *dev) 616 { 617 void __iomem *ioaddr = hw->pcsr; 618 u32 v; 619 620 v = (8 << EMAC_BURSTLEN_SHIFT); /* burst len */ 621 writel(v, ioaddr + EMAC_BASIC_CTL1); 622 } 623 624 static void sun8i_dwmac_set_mac(void __iomem *ioaddr, bool enable) 625 { 626 u32 t, r; 627 628 t = readl(ioaddr + EMAC_TX_CTL0); 629 r = readl(ioaddr + EMAC_RX_CTL0); 630 if (enable) { 631 t |= EMAC_TX_TRANSMITTER_EN; 632 r |= EMAC_RX_RECEIVER_EN; 633 } else { 634 t &= ~EMAC_TX_TRANSMITTER_EN; 635 r &= ~EMAC_RX_RECEIVER_EN; 636 } 637 writel(t, ioaddr + EMAC_TX_CTL0); 638 writel(r, ioaddr + EMAC_RX_CTL0); 639 } 640 641 /* Set MAC address at slot reg_n 642 * All slot > 0 need to be enabled with MAC_ADDR_TYPE_DST 643 * If addr is NULL, clear the slot 644 */ 645 static void sun8i_dwmac_set_umac_addr(struct mac_device_info *hw, 646 const unsigned char *addr, 647 unsigned int reg_n) 648 { 649 void __iomem *ioaddr = hw->pcsr; 650 u32 v; 651 652 if (!addr) { 653 writel(0, ioaddr + EMAC_MACADDR_HI(reg_n)); 654 return; 655 } 656 657 stmmac_set_mac_addr(ioaddr, addr, EMAC_MACADDR_HI(reg_n), 658 EMAC_MACADDR_LO(reg_n)); 659 if (reg_n > 0) { 660 v = readl(ioaddr + EMAC_MACADDR_HI(reg_n)); 661 v |= MAC_ADDR_TYPE_DST; 662 writel(v, ioaddr + EMAC_MACADDR_HI(reg_n)); 663 } 664 } 665 666 static void sun8i_dwmac_get_umac_addr(struct mac_device_info *hw, 667 unsigned char *addr, 668 unsigned int reg_n) 669 { 670 void __iomem *ioaddr = hw->pcsr; 671 672 stmmac_get_mac_addr(ioaddr, addr, EMAC_MACADDR_HI(reg_n), 673 EMAC_MACADDR_LO(reg_n)); 674 } 675 676 /* caution this function must return non 0 to work */ 677 static int sun8i_dwmac_rx_ipc_enable(struct mac_device_info *hw) 678 { 679 void __iomem *ioaddr = hw->pcsr; 680 u32 v; 681 682 v = readl(ioaddr + EMAC_RX_CTL0); 683 v |= EMAC_RX_DO_CRC; 684 writel(v, ioaddr + EMAC_RX_CTL0); 685 686 return 1; 687 } 688 689 static void sun8i_dwmac_set_filter(struct mac_device_info *hw, 690 struct net_device *dev) 691 { 692 void __iomem *ioaddr = hw->pcsr; 693 u32 v; 694 int i = 1; 695 struct netdev_hw_addr *ha; 696 int macaddrs = netdev_uc_count(dev) + netdev_mc_count(dev) + 1; 697 698 v = EMAC_FRM_FLT_CTL; 699 700 if (dev->flags & IFF_PROMISC) { 701 v = EMAC_FRM_FLT_RXALL; 702 } else if (dev->flags & IFF_ALLMULTI) { 703 v |= EMAC_FRM_FLT_MULTICAST; 704 } else if (macaddrs <= hw->unicast_filter_entries) { 705 if (!netdev_mc_empty(dev)) { 706 netdev_for_each_mc_addr(ha, dev) { 707 sun8i_dwmac_set_umac_addr(hw, ha->addr, i); 708 i++; 709 } 710 } 711 if (!netdev_uc_empty(dev)) { 712 netdev_for_each_uc_addr(ha, dev) { 713 sun8i_dwmac_set_umac_addr(hw, ha->addr, i); 714 i++; 715 } 716 } 717 } else { 718 if (!(readl(ioaddr + EMAC_RX_FRM_FLT) & EMAC_FRM_FLT_RXALL)) 719 netdev_info(dev, "Too many address, switching to promiscuous\n"); 720 v = EMAC_FRM_FLT_RXALL; 721 } 722 723 /* Disable unused address filter slots */ 724 while (i < hw->unicast_filter_entries) 725 sun8i_dwmac_set_umac_addr(hw, NULL, i++); 726 727 writel(v, ioaddr + EMAC_RX_FRM_FLT); 728 } 729 730 static void sun8i_dwmac_flow_ctrl(struct mac_device_info *hw, 731 unsigned int duplex, unsigned int fc, 732 unsigned int pause_time, u32 tx_cnt) 733 { 734 void __iomem *ioaddr = hw->pcsr; 735 u32 v; 736 737 v = readl(ioaddr + EMAC_RX_CTL0); 738 if (fc == FLOW_AUTO) 739 v |= EMAC_RX_FLOW_CTL_EN; 740 else 741 v &= ~EMAC_RX_FLOW_CTL_EN; 742 writel(v, ioaddr + EMAC_RX_CTL0); 743 744 v = readl(ioaddr + EMAC_TX_FLOW_CTL); 745 if (fc == FLOW_AUTO) 746 v |= EMAC_TX_FLOW_CTL_EN; 747 else 748 v &= ~EMAC_TX_FLOW_CTL_EN; 749 writel(v, ioaddr + EMAC_TX_FLOW_CTL); 750 } 751 752 static int sun8i_dwmac_reset(struct stmmac_priv *priv) 753 { 754 u32 v; 755 int err; 756 757 v = readl(priv->ioaddr + EMAC_BASIC_CTL1); 758 writel(v | 0x01, priv->ioaddr + EMAC_BASIC_CTL1); 759 760 /* The timeout was previoulsy set to 10ms, but some board (OrangePI0) 761 * need more if no cable plugged. 100ms seems OK 762 */ 763 err = readl_poll_timeout(priv->ioaddr + EMAC_BASIC_CTL1, v, 764 !(v & 0x01), 100, 100000); 765 766 if (err) { 767 dev_err(priv->device, "EMAC reset timeout\n"); 768 return err; 769 } 770 return 0; 771 } 772 773 /* Search in mdio-mux node for internal PHY node and get its clk/reset */ 774 static int get_ephy_nodes(struct stmmac_priv *priv) 775 { 776 struct sunxi_priv_data *gmac = priv->plat->bsp_priv; 777 struct device_node *mdio_internal; 778 struct device_node *mdio_mux; 779 int ret; 780 781 mdio_mux = of_get_child_by_name(priv->device->of_node, "mdio-mux"); 782 if (!mdio_mux) { 783 dev_err(priv->device, "Cannot get mdio-mux node\n"); 784 return -ENODEV; 785 } 786 787 mdio_internal = of_get_compatible_child(mdio_mux, 788 "allwinner,sun8i-h3-mdio-internal"); 789 of_node_put(mdio_mux); 790 if (!mdio_internal) { 791 dev_err(priv->device, "Cannot get internal_mdio node\n"); 792 return -ENODEV; 793 } 794 795 /* Seek for internal PHY */ 796 for_each_child_of_node_scoped(mdio_internal, iphynode) { 797 gmac->ephy_clk = of_clk_get(iphynode, 0); 798 if (IS_ERR(gmac->ephy_clk)) 799 continue; 800 gmac->rst_ephy = of_reset_control_get_exclusive(iphynode, NULL); 801 if (IS_ERR(gmac->rst_ephy)) { 802 ret = PTR_ERR(gmac->rst_ephy); 803 if (ret == -EPROBE_DEFER) { 804 of_node_put(mdio_internal); 805 return ret; 806 } 807 continue; 808 } 809 dev_info(priv->device, "Found internal PHY node\n"); 810 of_node_put(mdio_internal); 811 return 0; 812 } 813 814 of_node_put(mdio_internal); 815 return -ENODEV; 816 } 817 818 static int sun8i_dwmac_power_internal_phy(struct stmmac_priv *priv) 819 { 820 struct sunxi_priv_data *gmac = priv->plat->bsp_priv; 821 int ret; 822 823 if (gmac->internal_phy_powered) { 824 dev_warn(priv->device, "Internal PHY already powered\n"); 825 return 0; 826 } 827 828 dev_info(priv->device, "Powering internal PHY\n"); 829 ret = clk_prepare_enable(gmac->ephy_clk); 830 if (ret) { 831 dev_err(priv->device, "Cannot enable internal PHY\n"); 832 return ret; 833 } 834 835 /* Make sure the EPHY is properly reseted, as U-Boot may leave 836 * it at deasserted state, and thus it may fail to reset EMAC. 837 * 838 * This assumes the driver has exclusive access to the EPHY reset. 839 */ 840 ret = reset_control_reset(gmac->rst_ephy); 841 if (ret) { 842 dev_err(priv->device, "Cannot reset internal PHY\n"); 843 clk_disable_unprepare(gmac->ephy_clk); 844 return ret; 845 } 846 847 gmac->internal_phy_powered = true; 848 849 return 0; 850 } 851 852 static void sun8i_dwmac_unpower_internal_phy(struct sunxi_priv_data *gmac) 853 { 854 if (!gmac->internal_phy_powered) 855 return; 856 857 clk_disable_unprepare(gmac->ephy_clk); 858 reset_control_assert(gmac->rst_ephy); 859 gmac->internal_phy_powered = false; 860 } 861 862 /* MDIO multiplexing switch function 863 * This function is called by the mdio-mux layer when it thinks the mdio bus 864 * multiplexer needs to switch. 865 * 'current_child' is the current value of the mux register 866 * 'desired_child' is the value of the 'reg' property of the target child MDIO 867 * node. 868 * The first time this function is called, current_child == -1. 869 * If current_child == desired_child, then the mux is already set to the 870 * correct bus. 871 */ 872 static int mdio_mux_syscon_switch_fn(int current_child, int desired_child, 873 void *data) 874 { 875 struct stmmac_priv *priv = data; 876 struct sunxi_priv_data *gmac = priv->plat->bsp_priv; 877 u32 reg, val; 878 int ret = 0; 879 880 if (current_child ^ desired_child) { 881 regmap_field_read(gmac->regmap_field, ®); 882 switch (desired_child) { 883 case DWMAC_SUN8I_MDIO_MUX_INTERNAL_ID: 884 dev_info(priv->device, "Switch mux to internal PHY"); 885 val = (reg & ~H3_EPHY_MUX_MASK) | H3_EPHY_SELECT; 886 gmac->use_internal_phy = true; 887 break; 888 case DWMAC_SUN8I_MDIO_MUX_EXTERNAL_ID: 889 dev_info(priv->device, "Switch mux to external PHY"); 890 val = (reg & ~H3_EPHY_MUX_MASK) | H3_EPHY_SHUTDOWN; 891 gmac->use_internal_phy = false; 892 break; 893 default: 894 dev_err(priv->device, "Invalid child ID %x\n", 895 desired_child); 896 return -EINVAL; 897 } 898 regmap_field_write(gmac->regmap_field, val); 899 if (gmac->use_internal_phy) { 900 ret = sun8i_dwmac_power_internal_phy(priv); 901 if (ret) 902 return ret; 903 } else { 904 sun8i_dwmac_unpower_internal_phy(gmac); 905 } 906 /* After changing syscon value, the MAC need reset or it will 907 * use the last value (and so the last PHY set). 908 */ 909 ret = sun8i_dwmac_reset(priv); 910 } 911 return ret; 912 } 913 914 static int sun8i_dwmac_register_mdio_mux(struct stmmac_priv *priv) 915 { 916 int ret; 917 struct device_node *mdio_mux; 918 struct sunxi_priv_data *gmac = priv->plat->bsp_priv; 919 920 mdio_mux = of_get_child_by_name(priv->device->of_node, "mdio-mux"); 921 if (!mdio_mux) 922 return -ENODEV; 923 924 ret = mdio_mux_init(priv->device, mdio_mux, mdio_mux_syscon_switch_fn, 925 &gmac->mux_handle, priv, priv->mii); 926 of_node_put(mdio_mux); 927 return ret; 928 } 929 930 static int sun8i_dwmac_set_syscon(struct device *dev, 931 struct plat_stmmacenet_data *plat) 932 { 933 struct sunxi_priv_data *gmac = plat->bsp_priv; 934 struct device_node *node = dev->of_node; 935 int ret; 936 u32 reg, val; 937 938 ret = regmap_field_read(gmac->regmap_field, &val); 939 if (ret) { 940 dev_err(dev, "Fail to read from regmap field.\n"); 941 return ret; 942 } 943 944 reg = gmac->variant->default_syscon_value; 945 if (reg != val) 946 dev_warn(dev, 947 "Current syscon value is not the default %x (expect %x)\n", 948 val, reg); 949 950 if (gmac->variant->soc_has_internal_phy) { 951 if (of_property_read_bool(node, "allwinner,leds-active-low")) 952 reg |= H3_EPHY_LED_POL; 953 else 954 reg &= ~H3_EPHY_LED_POL; 955 956 /* Force EPHY xtal frequency to 24MHz. */ 957 reg |= H3_EPHY_CLK_SEL; 958 959 ret = of_mdio_parse_addr(dev, plat->phy_node); 960 if (ret < 0) { 961 dev_err(dev, "Could not parse MDIO addr\n"); 962 return ret; 963 } 964 /* of_mdio_parse_addr returns a valid (0 ~ 31) PHY 965 * address. No need to mask it again. 966 */ 967 reg |= 1 << H3_EPHY_ADDR_SHIFT; 968 } else { 969 /* For SoCs without internal PHY the PHY selection bit should be 970 * set to 0 (external PHY). 971 */ 972 reg &= ~H3_EPHY_SELECT; 973 } 974 975 if (!of_property_read_u32(node, "allwinner,tx-delay-ps", &val)) { 976 if (val % 100) { 977 dev_err(dev, "tx-delay must be a multiple of 100\n"); 978 return -EINVAL; 979 } 980 val /= 100; 981 dev_dbg(dev, "set tx-delay to %x\n", val); 982 if (val <= gmac->variant->tx_delay_max) { 983 reg &= ~(gmac->variant->tx_delay_max << 984 SYSCON_ETXDC_SHIFT); 985 reg |= (val << SYSCON_ETXDC_SHIFT); 986 } else { 987 dev_err(dev, "Invalid TX clock delay: %d\n", 988 val); 989 return -EINVAL; 990 } 991 } 992 993 if (!of_property_read_u32(node, "allwinner,rx-delay-ps", &val)) { 994 if (val % 100) { 995 dev_err(dev, "rx-delay must be a multiple of 100\n"); 996 return -EINVAL; 997 } 998 val /= 100; 999 dev_dbg(dev, "set rx-delay to %x\n", val); 1000 if (val <= gmac->variant->rx_delay_max) { 1001 reg &= ~(gmac->variant->rx_delay_max << 1002 SYSCON_ERXDC_SHIFT); 1003 reg |= (val << SYSCON_ERXDC_SHIFT); 1004 } else { 1005 dev_err(dev, "Invalid RX clock delay: %d\n", 1006 val); 1007 return -EINVAL; 1008 } 1009 } 1010 1011 /* Clear interface mode bits */ 1012 reg &= ~(SYSCON_ETCS_MASK | SYSCON_EPIT); 1013 if (gmac->variant->support_rmii) 1014 reg &= ~SYSCON_RMII_EN; 1015 1016 switch (plat->mac_interface) { 1017 case PHY_INTERFACE_MODE_MII: 1018 /* default */ 1019 break; 1020 case PHY_INTERFACE_MODE_RGMII: 1021 case PHY_INTERFACE_MODE_RGMII_ID: 1022 case PHY_INTERFACE_MODE_RGMII_RXID: 1023 case PHY_INTERFACE_MODE_RGMII_TXID: 1024 reg |= SYSCON_EPIT | SYSCON_ETCS_INT_GMII; 1025 break; 1026 case PHY_INTERFACE_MODE_RMII: 1027 reg |= SYSCON_RMII_EN | SYSCON_ETCS_EXT_GMII; 1028 break; 1029 default: 1030 dev_err(dev, "Unsupported interface mode: %s", 1031 phy_modes(plat->mac_interface)); 1032 return -EINVAL; 1033 } 1034 1035 regmap_field_write(gmac->regmap_field, reg); 1036 1037 return 0; 1038 } 1039 1040 static void sun8i_dwmac_unset_syscon(struct sunxi_priv_data *gmac) 1041 { 1042 u32 reg = gmac->variant->default_syscon_value; 1043 1044 regmap_field_write(gmac->regmap_field, reg); 1045 } 1046 1047 static void sun8i_dwmac_exit(struct platform_device *pdev, void *priv) 1048 { 1049 struct sunxi_priv_data *gmac = priv; 1050 1051 if (gmac->variant->soc_has_internal_phy) 1052 sun8i_dwmac_unpower_internal_phy(gmac); 1053 1054 if (gmac->regulator) 1055 regulator_disable(gmac->regulator); 1056 } 1057 1058 static void sun8i_dwmac_set_mac_loopback(void __iomem *ioaddr, bool enable) 1059 { 1060 u32 value = readl(ioaddr + EMAC_BASIC_CTL0); 1061 1062 if (enable) 1063 value |= EMAC_LOOPBACK; 1064 else 1065 value &= ~EMAC_LOOPBACK; 1066 1067 writel(value, ioaddr + EMAC_BASIC_CTL0); 1068 } 1069 1070 static const struct stmmac_ops sun8i_dwmac_ops = { 1071 .core_init = sun8i_dwmac_core_init, 1072 .set_mac = sun8i_dwmac_set_mac, 1073 .dump_regs = sun8i_dwmac_dump_mac_regs, 1074 .rx_ipc = sun8i_dwmac_rx_ipc_enable, 1075 .set_filter = sun8i_dwmac_set_filter, 1076 .flow_ctrl = sun8i_dwmac_flow_ctrl, 1077 .set_umac_addr = sun8i_dwmac_set_umac_addr, 1078 .get_umac_addr = sun8i_dwmac_get_umac_addr, 1079 .set_mac_loopback = sun8i_dwmac_set_mac_loopback, 1080 }; 1081 1082 static struct mac_device_info *sun8i_dwmac_setup(void *ppriv) 1083 { 1084 struct mac_device_info *mac; 1085 struct stmmac_priv *priv = ppriv; 1086 1087 mac = devm_kzalloc(priv->device, sizeof(*mac), GFP_KERNEL); 1088 if (!mac) 1089 return NULL; 1090 1091 mac->pcsr = priv->ioaddr; 1092 mac->mac = &sun8i_dwmac_ops; 1093 mac->dma = &sun8i_dwmac_dma_ops; 1094 1095 priv->dev->priv_flags |= IFF_UNICAST_FLT; 1096 1097 mac->link.caps = MAC_ASYM_PAUSE | MAC_SYM_PAUSE | 1098 MAC_10 | MAC_100 | MAC_1000; 1099 /* The loopback bit seems to be re-set when link change 1100 * Simply mask it each time 1101 * Speed 10/100/1000 are set in BIT(2)/BIT(3) 1102 */ 1103 mac->link.speed_mask = GENMASK(3, 2) | EMAC_LOOPBACK; 1104 mac->link.speed10 = EMAC_SPEED_10; 1105 mac->link.speed100 = EMAC_SPEED_100; 1106 mac->link.speed1000 = EMAC_SPEED_1000; 1107 mac->link.duplex = EMAC_DUPLEX_FULL; 1108 mac->mii.addr = EMAC_MDIO_CMD; 1109 mac->mii.data = EMAC_MDIO_DATA; 1110 mac->mii.reg_shift = 4; 1111 mac->mii.reg_mask = GENMASK(8, 4); 1112 mac->mii.addr_shift = 12; 1113 mac->mii.addr_mask = GENMASK(16, 12); 1114 mac->mii.clk_csr_shift = 20; 1115 mac->mii.clk_csr_mask = GENMASK(22, 20); 1116 mac->unicast_filter_entries = 8; 1117 1118 /* Synopsys Id is not available */ 1119 priv->synopsys_id = 0; 1120 1121 return mac; 1122 } 1123 1124 static struct regmap *sun8i_dwmac_get_syscon_from_dev(struct device_node *node) 1125 { 1126 struct device_node *syscon_node; 1127 struct platform_device *syscon_pdev; 1128 struct regmap *regmap = NULL; 1129 1130 syscon_node = of_parse_phandle(node, "syscon", 0); 1131 if (!syscon_node) 1132 return ERR_PTR(-ENODEV); 1133 1134 syscon_pdev = of_find_device_by_node(syscon_node); 1135 if (!syscon_pdev) { 1136 /* platform device might not be probed yet */ 1137 regmap = ERR_PTR(-EPROBE_DEFER); 1138 goto out_put_node; 1139 } 1140 1141 /* If no regmap is found then the other device driver is at fault */ 1142 regmap = dev_get_regmap(&syscon_pdev->dev, NULL); 1143 if (!regmap) 1144 regmap = ERR_PTR(-EINVAL); 1145 1146 platform_device_put(syscon_pdev); 1147 out_put_node: 1148 of_node_put(syscon_node); 1149 return regmap; 1150 } 1151 1152 static int sun8i_dwmac_probe(struct platform_device *pdev) 1153 { 1154 struct plat_stmmacenet_data *plat_dat; 1155 struct stmmac_resources stmmac_res; 1156 struct sunxi_priv_data *gmac; 1157 struct device *dev = &pdev->dev; 1158 phy_interface_t interface; 1159 int ret; 1160 struct stmmac_priv *priv; 1161 struct net_device *ndev; 1162 struct regmap *regmap; 1163 1164 ret = stmmac_get_platform_resources(pdev, &stmmac_res); 1165 if (ret) 1166 return ret; 1167 1168 gmac = devm_kzalloc(dev, sizeof(*gmac), GFP_KERNEL); 1169 if (!gmac) 1170 return -ENOMEM; 1171 1172 gmac->variant = of_device_get_match_data(&pdev->dev); 1173 if (!gmac->variant) { 1174 dev_err(&pdev->dev, "Missing dwmac-sun8i variant\n"); 1175 return -EINVAL; 1176 } 1177 1178 /* Optional regulator for PHY */ 1179 gmac->regulator = devm_regulator_get_optional(dev, "phy"); 1180 if (IS_ERR(gmac->regulator)) { 1181 if (PTR_ERR(gmac->regulator) == -EPROBE_DEFER) 1182 return -EPROBE_DEFER; 1183 dev_info(dev, "No regulator found\n"); 1184 gmac->regulator = NULL; 1185 } 1186 1187 /* The "GMAC clock control" register might be located in the 1188 * CCU address range (on the R40), or the system control address 1189 * range (on most other sun8i and later SoCs). 1190 * 1191 * The former controls most if not all clocks in the SoC. The 1192 * latter has an SoC identification register, and on some SoCs, 1193 * controls to map device specific SRAM to either the intended 1194 * peripheral, or the CPU address space. 1195 * 1196 * In either case, there should be a coordinated and restricted 1197 * method of accessing the register needed here. This is done by 1198 * having the device export a custom regmap, instead of a generic 1199 * syscon, which grants all access to all registers. 1200 * 1201 * To support old device trees, we fall back to using the syscon 1202 * interface if possible. 1203 */ 1204 regmap = sun8i_dwmac_get_syscon_from_dev(pdev->dev.of_node); 1205 if (IS_ERR(regmap)) 1206 regmap = syscon_regmap_lookup_by_phandle(pdev->dev.of_node, 1207 "syscon"); 1208 if (IS_ERR(regmap)) { 1209 ret = PTR_ERR(regmap); 1210 dev_err(&pdev->dev, "Unable to map syscon: %d\n", ret); 1211 return ret; 1212 } 1213 1214 gmac->regmap_field = devm_regmap_field_alloc(dev, regmap, 1215 *gmac->variant->syscon_field); 1216 if (IS_ERR(gmac->regmap_field)) { 1217 ret = PTR_ERR(gmac->regmap_field); 1218 dev_err(dev, "Unable to map syscon register: %d\n", ret); 1219 return ret; 1220 } 1221 1222 ret = of_get_phy_mode(dev->of_node, &interface); 1223 if (ret) 1224 return -EINVAL; 1225 1226 plat_dat = devm_stmmac_probe_config_dt(pdev, stmmac_res.mac); 1227 if (IS_ERR(plat_dat)) 1228 return PTR_ERR(plat_dat); 1229 1230 /* platform data specifying hardware features and callbacks. 1231 * hardware features were copied from Allwinner drivers. 1232 */ 1233 plat_dat->mac_interface = interface; 1234 plat_dat->rx_coe = STMMAC_RX_COE_TYPE2; 1235 plat_dat->tx_coe = 1; 1236 plat_dat->flags |= STMMAC_FLAG_HAS_SUN8I; 1237 plat_dat->bsp_priv = gmac; 1238 plat_dat->init = sun8i_dwmac_init; 1239 plat_dat->exit = sun8i_dwmac_exit; 1240 plat_dat->setup = sun8i_dwmac_setup; 1241 plat_dat->tx_fifo_size = 4096; 1242 plat_dat->rx_fifo_size = 16384; 1243 1244 ret = sun8i_dwmac_set_syscon(&pdev->dev, plat_dat); 1245 if (ret) 1246 return ret; 1247 1248 ret = sun8i_dwmac_init(pdev, plat_dat->bsp_priv); 1249 if (ret) 1250 goto dwmac_syscon; 1251 1252 ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res); 1253 if (ret) 1254 goto dwmac_exit; 1255 1256 ndev = dev_get_drvdata(&pdev->dev); 1257 priv = netdev_priv(ndev); 1258 1259 /* the MAC is runtime suspended after stmmac_dvr_probe(), so we 1260 * need to ensure the MAC resume back before other operations such 1261 * as reset. 1262 */ 1263 pm_runtime_get_sync(&pdev->dev); 1264 1265 /* The mux must be registered after parent MDIO 1266 * so after stmmac_dvr_probe() 1267 */ 1268 if (gmac->variant->soc_has_internal_phy) { 1269 ret = get_ephy_nodes(priv); 1270 if (ret) 1271 goto dwmac_remove; 1272 ret = sun8i_dwmac_register_mdio_mux(priv); 1273 if (ret) { 1274 dev_err(&pdev->dev, "Failed to register mux\n"); 1275 goto dwmac_mux; 1276 } 1277 } else { 1278 ret = sun8i_dwmac_reset(priv); 1279 if (ret) 1280 goto dwmac_remove; 1281 } 1282 1283 pm_runtime_put(&pdev->dev); 1284 1285 return 0; 1286 1287 dwmac_mux: 1288 reset_control_put(gmac->rst_ephy); 1289 clk_put(gmac->ephy_clk); 1290 dwmac_remove: 1291 pm_runtime_put_noidle(&pdev->dev); 1292 stmmac_dvr_remove(&pdev->dev); 1293 dwmac_exit: 1294 sun8i_dwmac_exit(pdev, gmac); 1295 dwmac_syscon: 1296 sun8i_dwmac_unset_syscon(gmac); 1297 1298 return ret; 1299 } 1300 1301 static void sun8i_dwmac_remove(struct platform_device *pdev) 1302 { 1303 struct net_device *ndev = platform_get_drvdata(pdev); 1304 struct stmmac_priv *priv = netdev_priv(ndev); 1305 struct sunxi_priv_data *gmac = priv->plat->bsp_priv; 1306 1307 if (gmac->variant->soc_has_internal_phy) { 1308 mdio_mux_uninit(gmac->mux_handle); 1309 sun8i_dwmac_unpower_internal_phy(gmac); 1310 reset_control_put(gmac->rst_ephy); 1311 clk_put(gmac->ephy_clk); 1312 } 1313 1314 stmmac_pltfr_remove(pdev); 1315 sun8i_dwmac_unset_syscon(gmac); 1316 } 1317 1318 static void sun8i_dwmac_shutdown(struct platform_device *pdev) 1319 { 1320 struct net_device *ndev = platform_get_drvdata(pdev); 1321 struct stmmac_priv *priv = netdev_priv(ndev); 1322 struct sunxi_priv_data *gmac = priv->plat->bsp_priv; 1323 1324 sun8i_dwmac_exit(pdev, gmac); 1325 } 1326 1327 static const struct of_device_id sun8i_dwmac_match[] = { 1328 { .compatible = "allwinner,sun8i-h3-emac", 1329 .data = &emac_variant_h3 }, 1330 { .compatible = "allwinner,sun8i-v3s-emac", 1331 .data = &emac_variant_v3s }, 1332 { .compatible = "allwinner,sun8i-a83t-emac", 1333 .data = &emac_variant_a83t }, 1334 { .compatible = "allwinner,sun8i-r40-gmac", 1335 .data = &emac_variant_r40 }, 1336 { .compatible = "allwinner,sun50i-a64-emac", 1337 .data = &emac_variant_a64 }, 1338 { .compatible = "allwinner,sun50i-h6-emac", 1339 .data = &emac_variant_h6 }, 1340 { } 1341 }; 1342 MODULE_DEVICE_TABLE(of, sun8i_dwmac_match); 1343 1344 static struct platform_driver sun8i_dwmac_driver = { 1345 .probe = sun8i_dwmac_probe, 1346 .remove_new = sun8i_dwmac_remove, 1347 .shutdown = sun8i_dwmac_shutdown, 1348 .driver = { 1349 .name = "dwmac-sun8i", 1350 .pm = &stmmac_pltfr_pm_ops, 1351 .of_match_table = sun8i_dwmac_match, 1352 }, 1353 }; 1354 module_platform_driver(sun8i_dwmac_driver); 1355 1356 MODULE_AUTHOR("Corentin Labbe <clabbe.montjoie@gmail.com>"); 1357 MODULE_DESCRIPTION("Allwinner sun8i DWMAC specific glue layer"); 1358 MODULE_LICENSE("GPL"); 1359