1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /*************************************************************************** 3 * 4 * Copyright (C) 2004-2008 SMSC 5 * Copyright (C) 2005-2008 ARM 6 * 7 *************************************************************************** 8 * Rewritten, heavily based on smsc911x simple driver by SMSC. 9 * Partly uses io macros from smc91x.c by Nicolas Pitre 10 * 11 * Supported devices: 12 * LAN9115, LAN9116, LAN9117, LAN9118 13 * LAN9215, LAN9216, LAN9217, LAN9218 14 * LAN9210, LAN9211 15 * LAN9220, LAN9221 16 * LAN89218,LAN9250 17 */ 18 19 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt 20 21 #include <linux/crc32.h> 22 #include <linux/clk.h> 23 #include <linux/delay.h> 24 #include <linux/errno.h> 25 #include <linux/etherdevice.h> 26 #include <linux/ethtool.h> 27 #include <linux/init.h> 28 #include <linux/interrupt.h> 29 #include <linux/ioport.h> 30 #include <linux/kernel.h> 31 #include <linux/module.h> 32 #include <linux/netdevice.h> 33 #include <linux/platform_device.h> 34 #include <linux/regulator/consumer.h> 35 #include <linux/sched.h> 36 #include <linux/timer.h> 37 #include <linux/bug.h> 38 #include <linux/bitops.h> 39 #include <linux/irq.h> 40 #include <linux/io.h> 41 #include <linux/swab.h> 42 #include <linux/phy.h> 43 #include <linux/smsc911x.h> 44 #include <linux/device.h> 45 #include <linux/of.h> 46 #include <linux/of_gpio.h> 47 #include <linux/of_net.h> 48 #include <linux/acpi.h> 49 #include <linux/pm_runtime.h> 50 #include <linux/property.h> 51 #include <linux/gpio/consumer.h> 52 53 #include "smsc911x.h" 54 55 #define SMSC_CHIPNAME "smsc911x" 56 #define SMSC_MDIONAME "smsc911x-mdio" 57 #define SMSC_DRV_VERSION "2008-10-21" 58 59 MODULE_DESCRIPTION("SMSC LAN911x/LAN921x Ethernet driver"); 60 MODULE_LICENSE("GPL"); 61 MODULE_VERSION(SMSC_DRV_VERSION); 62 MODULE_ALIAS("platform:smsc911x"); 63 64 #if USE_DEBUG > 0 65 static int debug = 16; 66 #else 67 static int debug = 3; 68 #endif 69 70 module_param(debug, int, 0); 71 MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)"); 72 73 struct smsc911x_data; 74 75 struct smsc911x_ops { 76 u32 (*reg_read)(struct smsc911x_data *pdata, u32 reg); 77 void (*reg_write)(struct smsc911x_data *pdata, u32 reg, u32 val); 78 void (*rx_readfifo)(struct smsc911x_data *pdata, 79 unsigned int *buf, unsigned int wordcount); 80 void (*tx_writefifo)(struct smsc911x_data *pdata, 81 unsigned int *buf, unsigned int wordcount); 82 }; 83 84 #define SMSC911X_NUM_SUPPLIES 2 85 86 struct smsc911x_data { 87 void __iomem *ioaddr; 88 89 unsigned int idrev; 90 91 /* used to decide which workarounds apply */ 92 unsigned int generation; 93 94 /* device configuration (copied from platform_data during probe) */ 95 struct smsc911x_platform_config config; 96 97 /* This needs to be acquired before calling any of below: 98 * smsc911x_mac_read(), smsc911x_mac_write() 99 */ 100 spinlock_t mac_lock; 101 102 /* spinlock to ensure register accesses are serialised */ 103 spinlock_t dev_lock; 104 105 struct mii_bus *mii_bus; 106 unsigned int using_extphy; 107 int last_duplex; 108 int last_carrier; 109 110 u32 msg_enable; 111 unsigned int gpio_setting; 112 unsigned int gpio_orig_setting; 113 struct net_device *dev; 114 struct napi_struct napi; 115 116 unsigned int software_irq_signal; 117 118 #ifdef USE_PHY_WORK_AROUND 119 #define MIN_PACKET_SIZE (64) 120 char loopback_tx_pkt[MIN_PACKET_SIZE]; 121 char loopback_rx_pkt[MIN_PACKET_SIZE]; 122 unsigned int resetcount; 123 #endif 124 125 /* Members for Multicast filter workaround */ 126 unsigned int multicast_update_pending; 127 unsigned int set_bits_mask; 128 unsigned int clear_bits_mask; 129 unsigned int hashhi; 130 unsigned int hashlo; 131 132 /* register access functions */ 133 const struct smsc911x_ops *ops; 134 135 /* regulators */ 136 struct regulator_bulk_data supplies[SMSC911X_NUM_SUPPLIES]; 137 138 /* Reset GPIO */ 139 struct gpio_desc *reset_gpiod; 140 141 /* clock */ 142 struct clk *clk; 143 }; 144 145 /* Easy access to information */ 146 #define __smsc_shift(pdata, reg) ((reg) << ((pdata)->config.shift)) 147 148 static inline u32 __smsc911x_reg_read(struct smsc911x_data *pdata, u32 reg) 149 { 150 if (pdata->config.flags & SMSC911X_USE_32BIT) 151 return readl(pdata->ioaddr + reg); 152 153 if (pdata->config.flags & SMSC911X_USE_16BIT) 154 return ((readw(pdata->ioaddr + reg) & 0xFFFF) | 155 ((readw(pdata->ioaddr + reg + 2) & 0xFFFF) << 16)); 156 157 BUG(); 158 return 0; 159 } 160 161 static inline u32 162 __smsc911x_reg_read_shift(struct smsc911x_data *pdata, u32 reg) 163 { 164 if (pdata->config.flags & SMSC911X_USE_32BIT) 165 return readl(pdata->ioaddr + __smsc_shift(pdata, reg)); 166 167 if (pdata->config.flags & SMSC911X_USE_16BIT) 168 return (readw(pdata->ioaddr + 169 __smsc_shift(pdata, reg)) & 0xFFFF) | 170 ((readw(pdata->ioaddr + 171 __smsc_shift(pdata, reg + 2)) & 0xFFFF) << 16); 172 173 BUG(); 174 return 0; 175 } 176 177 static inline u32 smsc911x_reg_read(struct smsc911x_data *pdata, u32 reg) 178 { 179 u32 data; 180 unsigned long flags; 181 182 spin_lock_irqsave(&pdata->dev_lock, flags); 183 data = pdata->ops->reg_read(pdata, reg); 184 spin_unlock_irqrestore(&pdata->dev_lock, flags); 185 186 return data; 187 } 188 189 static inline void __smsc911x_reg_write(struct smsc911x_data *pdata, u32 reg, 190 u32 val) 191 { 192 if (pdata->config.flags & SMSC911X_USE_32BIT) { 193 writel(val, pdata->ioaddr + reg); 194 return; 195 } 196 197 if (pdata->config.flags & SMSC911X_USE_16BIT) { 198 writew(val & 0xFFFF, pdata->ioaddr + reg); 199 writew((val >> 16) & 0xFFFF, pdata->ioaddr + reg + 2); 200 return; 201 } 202 203 BUG(); 204 } 205 206 static inline void 207 __smsc911x_reg_write_shift(struct smsc911x_data *pdata, u32 reg, u32 val) 208 { 209 if (pdata->config.flags & SMSC911X_USE_32BIT) { 210 writel(val, pdata->ioaddr + __smsc_shift(pdata, reg)); 211 return; 212 } 213 214 if (pdata->config.flags & SMSC911X_USE_16BIT) { 215 writew(val & 0xFFFF, 216 pdata->ioaddr + __smsc_shift(pdata, reg)); 217 writew((val >> 16) & 0xFFFF, 218 pdata->ioaddr + __smsc_shift(pdata, reg + 2)); 219 return; 220 } 221 222 BUG(); 223 } 224 225 static inline void smsc911x_reg_write(struct smsc911x_data *pdata, u32 reg, 226 u32 val) 227 { 228 unsigned long flags; 229 230 spin_lock_irqsave(&pdata->dev_lock, flags); 231 pdata->ops->reg_write(pdata, reg, val); 232 spin_unlock_irqrestore(&pdata->dev_lock, flags); 233 } 234 235 /* Writes a packet to the TX_DATA_FIFO */ 236 static inline void 237 smsc911x_tx_writefifo(struct smsc911x_data *pdata, unsigned int *buf, 238 unsigned int wordcount) 239 { 240 unsigned long flags; 241 242 spin_lock_irqsave(&pdata->dev_lock, flags); 243 244 if (pdata->config.flags & SMSC911X_SWAP_FIFO) { 245 while (wordcount--) 246 __smsc911x_reg_write(pdata, TX_DATA_FIFO, 247 swab32(*buf++)); 248 goto out; 249 } 250 251 if (pdata->config.flags & SMSC911X_USE_32BIT) { 252 iowrite32_rep(pdata->ioaddr + TX_DATA_FIFO, buf, wordcount); 253 goto out; 254 } 255 256 if (pdata->config.flags & SMSC911X_USE_16BIT) { 257 while (wordcount--) 258 __smsc911x_reg_write(pdata, TX_DATA_FIFO, *buf++); 259 goto out; 260 } 261 262 BUG(); 263 out: 264 spin_unlock_irqrestore(&pdata->dev_lock, flags); 265 } 266 267 /* Writes a packet to the TX_DATA_FIFO - shifted version */ 268 static inline void 269 smsc911x_tx_writefifo_shift(struct smsc911x_data *pdata, unsigned int *buf, 270 unsigned int wordcount) 271 { 272 unsigned long flags; 273 274 spin_lock_irqsave(&pdata->dev_lock, flags); 275 276 if (pdata->config.flags & SMSC911X_SWAP_FIFO) { 277 while (wordcount--) 278 __smsc911x_reg_write_shift(pdata, TX_DATA_FIFO, 279 swab32(*buf++)); 280 goto out; 281 } 282 283 if (pdata->config.flags & SMSC911X_USE_32BIT) { 284 iowrite32_rep(pdata->ioaddr + __smsc_shift(pdata, 285 TX_DATA_FIFO), buf, wordcount); 286 goto out; 287 } 288 289 if (pdata->config.flags & SMSC911X_USE_16BIT) { 290 while (wordcount--) 291 __smsc911x_reg_write_shift(pdata, 292 TX_DATA_FIFO, *buf++); 293 goto out; 294 } 295 296 BUG(); 297 out: 298 spin_unlock_irqrestore(&pdata->dev_lock, flags); 299 } 300 301 /* Reads a packet out of the RX_DATA_FIFO */ 302 static inline void 303 smsc911x_rx_readfifo(struct smsc911x_data *pdata, unsigned int *buf, 304 unsigned int wordcount) 305 { 306 unsigned long flags; 307 308 spin_lock_irqsave(&pdata->dev_lock, flags); 309 310 if (pdata->config.flags & SMSC911X_SWAP_FIFO) { 311 while (wordcount--) 312 *buf++ = swab32(__smsc911x_reg_read(pdata, 313 RX_DATA_FIFO)); 314 goto out; 315 } 316 317 if (pdata->config.flags & SMSC911X_USE_32BIT) { 318 ioread32_rep(pdata->ioaddr + RX_DATA_FIFO, buf, wordcount); 319 goto out; 320 } 321 322 if (pdata->config.flags & SMSC911X_USE_16BIT) { 323 while (wordcount--) 324 *buf++ = __smsc911x_reg_read(pdata, RX_DATA_FIFO); 325 goto out; 326 } 327 328 BUG(); 329 out: 330 spin_unlock_irqrestore(&pdata->dev_lock, flags); 331 } 332 333 /* Reads a packet out of the RX_DATA_FIFO - shifted version */ 334 static inline void 335 smsc911x_rx_readfifo_shift(struct smsc911x_data *pdata, unsigned int *buf, 336 unsigned int wordcount) 337 { 338 unsigned long flags; 339 340 spin_lock_irqsave(&pdata->dev_lock, flags); 341 342 if (pdata->config.flags & SMSC911X_SWAP_FIFO) { 343 while (wordcount--) 344 *buf++ = swab32(__smsc911x_reg_read_shift(pdata, 345 RX_DATA_FIFO)); 346 goto out; 347 } 348 349 if (pdata->config.flags & SMSC911X_USE_32BIT) { 350 ioread32_rep(pdata->ioaddr + __smsc_shift(pdata, 351 RX_DATA_FIFO), buf, wordcount); 352 goto out; 353 } 354 355 if (pdata->config.flags & SMSC911X_USE_16BIT) { 356 while (wordcount--) 357 *buf++ = __smsc911x_reg_read_shift(pdata, 358 RX_DATA_FIFO); 359 goto out; 360 } 361 362 BUG(); 363 out: 364 spin_unlock_irqrestore(&pdata->dev_lock, flags); 365 } 366 367 /* 368 * enable regulator and clock resources. 369 */ 370 static int smsc911x_enable_resources(struct platform_device *pdev) 371 { 372 struct net_device *ndev = platform_get_drvdata(pdev); 373 struct smsc911x_data *pdata = netdev_priv(ndev); 374 int ret = 0; 375 376 ret = regulator_bulk_enable(ARRAY_SIZE(pdata->supplies), 377 pdata->supplies); 378 if (ret) 379 netdev_err(ndev, "failed to enable regulators %d\n", 380 ret); 381 382 if (!IS_ERR(pdata->clk)) { 383 ret = clk_prepare_enable(pdata->clk); 384 if (ret < 0) 385 netdev_err(ndev, "failed to enable clock %d\n", ret); 386 } 387 388 return ret; 389 } 390 391 /* 392 * disable resources, currently just regulators. 393 */ 394 static int smsc911x_disable_resources(struct platform_device *pdev) 395 { 396 struct net_device *ndev = platform_get_drvdata(pdev); 397 struct smsc911x_data *pdata = netdev_priv(ndev); 398 int ret = 0; 399 400 ret = regulator_bulk_disable(ARRAY_SIZE(pdata->supplies), 401 pdata->supplies); 402 403 if (!IS_ERR(pdata->clk)) 404 clk_disable_unprepare(pdata->clk); 405 406 return ret; 407 } 408 409 /* 410 * Request resources, currently just regulators. 411 * 412 * The SMSC911x has two power pins: vddvario and vdd33a, in designs where 413 * these are not always-on we need to request regulators to be turned on 414 * before we can try to access the device registers. 415 */ 416 static int smsc911x_request_resources(struct platform_device *pdev) 417 { 418 struct net_device *ndev = platform_get_drvdata(pdev); 419 struct smsc911x_data *pdata = netdev_priv(ndev); 420 int ret = 0; 421 422 /* Request regulators */ 423 pdata->supplies[0].supply = "vdd33a"; 424 pdata->supplies[1].supply = "vddvario"; 425 ret = regulator_bulk_get(&pdev->dev, 426 ARRAY_SIZE(pdata->supplies), 427 pdata->supplies); 428 if (ret) { 429 /* 430 * Retry on deferrals, else just report the error 431 * and try to continue. 432 */ 433 if (ret == -EPROBE_DEFER) 434 return ret; 435 netdev_err(ndev, "couldn't get regulators %d\n", 436 ret); 437 } 438 439 /* Request optional RESET GPIO */ 440 pdata->reset_gpiod = devm_gpiod_get_optional(&pdev->dev, 441 "reset", 442 GPIOD_OUT_LOW); 443 444 /* Request clock */ 445 pdata->clk = clk_get(&pdev->dev, NULL); 446 if (IS_ERR(pdata->clk)) 447 dev_dbg(&pdev->dev, "couldn't get clock %li\n", 448 PTR_ERR(pdata->clk)); 449 450 return ret; 451 } 452 453 /* 454 * Free resources, currently just regulators. 455 * 456 */ 457 static void smsc911x_free_resources(struct platform_device *pdev) 458 { 459 struct net_device *ndev = platform_get_drvdata(pdev); 460 struct smsc911x_data *pdata = netdev_priv(ndev); 461 462 /* Free regulators */ 463 regulator_bulk_free(ARRAY_SIZE(pdata->supplies), 464 pdata->supplies); 465 466 /* Free clock */ 467 if (!IS_ERR(pdata->clk)) { 468 clk_put(pdata->clk); 469 pdata->clk = NULL; 470 } 471 } 472 473 /* waits for MAC not busy, with timeout. Only called by smsc911x_mac_read 474 * and smsc911x_mac_write, so assumes mac_lock is held */ 475 static int smsc911x_mac_complete(struct smsc911x_data *pdata) 476 { 477 int i; 478 u32 val; 479 480 SMSC_ASSERT_MAC_LOCK(pdata); 481 482 for (i = 0; i < 40; i++) { 483 val = smsc911x_reg_read(pdata, MAC_CSR_CMD); 484 if (!(val & MAC_CSR_CMD_CSR_BUSY_)) 485 return 0; 486 } 487 SMSC_WARN(pdata, hw, "Timed out waiting for MAC not BUSY. " 488 "MAC_CSR_CMD: 0x%08X", val); 489 return -EIO; 490 } 491 492 /* Fetches a MAC register value. Assumes mac_lock is acquired */ 493 static u32 smsc911x_mac_read(struct smsc911x_data *pdata, unsigned int offset) 494 { 495 unsigned int temp; 496 497 SMSC_ASSERT_MAC_LOCK(pdata); 498 499 temp = smsc911x_reg_read(pdata, MAC_CSR_CMD); 500 if (unlikely(temp & MAC_CSR_CMD_CSR_BUSY_)) { 501 SMSC_WARN(pdata, hw, "MAC busy at entry"); 502 return 0xFFFFFFFF; 503 } 504 505 /* Send the MAC cmd */ 506 smsc911x_reg_write(pdata, MAC_CSR_CMD, ((offset & 0xFF) | 507 MAC_CSR_CMD_CSR_BUSY_ | MAC_CSR_CMD_R_NOT_W_)); 508 509 /* Workaround for hardware read-after-write restriction */ 510 temp = smsc911x_reg_read(pdata, BYTE_TEST); 511 512 /* Wait for the read to complete */ 513 if (likely(smsc911x_mac_complete(pdata) == 0)) 514 return smsc911x_reg_read(pdata, MAC_CSR_DATA); 515 516 SMSC_WARN(pdata, hw, "MAC busy after read"); 517 return 0xFFFFFFFF; 518 } 519 520 /* Set a mac register, mac_lock must be acquired before calling */ 521 static void smsc911x_mac_write(struct smsc911x_data *pdata, 522 unsigned int offset, u32 val) 523 { 524 unsigned int temp; 525 526 SMSC_ASSERT_MAC_LOCK(pdata); 527 528 temp = smsc911x_reg_read(pdata, MAC_CSR_CMD); 529 if (unlikely(temp & MAC_CSR_CMD_CSR_BUSY_)) { 530 SMSC_WARN(pdata, hw, 531 "smsc911x_mac_write failed, MAC busy at entry"); 532 return; 533 } 534 535 /* Send data to write */ 536 smsc911x_reg_write(pdata, MAC_CSR_DATA, val); 537 538 /* Write the actual data */ 539 smsc911x_reg_write(pdata, MAC_CSR_CMD, ((offset & 0xFF) | 540 MAC_CSR_CMD_CSR_BUSY_)); 541 542 /* Workaround for hardware read-after-write restriction */ 543 temp = smsc911x_reg_read(pdata, BYTE_TEST); 544 545 /* Wait for the write to complete */ 546 if (likely(smsc911x_mac_complete(pdata) == 0)) 547 return; 548 549 SMSC_WARN(pdata, hw, "smsc911x_mac_write failed, MAC busy after write"); 550 } 551 552 /* Get a phy register */ 553 static int smsc911x_mii_read(struct mii_bus *bus, int phyaddr, int regidx) 554 { 555 struct smsc911x_data *pdata = bus->priv; 556 unsigned long flags; 557 unsigned int addr; 558 int i, reg; 559 560 pm_runtime_get_sync(bus->parent); 561 spin_lock_irqsave(&pdata->mac_lock, flags); 562 563 /* Confirm MII not busy */ 564 if (unlikely(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) { 565 SMSC_WARN(pdata, hw, "MII is busy in smsc911x_mii_read???"); 566 reg = -EIO; 567 goto out; 568 } 569 570 /* Set the address, index & direction (read from PHY) */ 571 addr = ((phyaddr & 0x1F) << 11) | ((regidx & 0x1F) << 6); 572 smsc911x_mac_write(pdata, MII_ACC, addr); 573 574 /* Wait for read to complete w/ timeout */ 575 for (i = 0; i < 100; i++) 576 if (!(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) { 577 reg = smsc911x_mac_read(pdata, MII_DATA); 578 goto out; 579 } 580 581 SMSC_WARN(pdata, hw, "Timed out waiting for MII read to finish"); 582 reg = -EIO; 583 584 out: 585 spin_unlock_irqrestore(&pdata->mac_lock, flags); 586 pm_runtime_put(bus->parent); 587 return reg; 588 } 589 590 /* Set a phy register */ 591 static int smsc911x_mii_write(struct mii_bus *bus, int phyaddr, int regidx, 592 u16 val) 593 { 594 struct smsc911x_data *pdata = bus->priv; 595 unsigned long flags; 596 unsigned int addr; 597 int i, reg; 598 599 pm_runtime_get_sync(bus->parent); 600 spin_lock_irqsave(&pdata->mac_lock, flags); 601 602 /* Confirm MII not busy */ 603 if (unlikely(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) { 604 SMSC_WARN(pdata, hw, "MII is busy in smsc911x_mii_write???"); 605 reg = -EIO; 606 goto out; 607 } 608 609 /* Put the data to write in the MAC */ 610 smsc911x_mac_write(pdata, MII_DATA, val); 611 612 /* Set the address, index & direction (write to PHY) */ 613 addr = ((phyaddr & 0x1F) << 11) | ((regidx & 0x1F) << 6) | 614 MII_ACC_MII_WRITE_; 615 smsc911x_mac_write(pdata, MII_ACC, addr); 616 617 /* Wait for write to complete w/ timeout */ 618 for (i = 0; i < 100; i++) 619 if (!(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) { 620 reg = 0; 621 goto out; 622 } 623 624 SMSC_WARN(pdata, hw, "Timed out waiting for MII write to finish"); 625 reg = -EIO; 626 627 out: 628 spin_unlock_irqrestore(&pdata->mac_lock, flags); 629 pm_runtime_put(bus->parent); 630 return reg; 631 } 632 633 /* Switch to external phy. Assumes tx and rx are stopped. */ 634 static void smsc911x_phy_enable_external(struct smsc911x_data *pdata) 635 { 636 unsigned int hwcfg = smsc911x_reg_read(pdata, HW_CFG); 637 638 /* Disable phy clocks to the MAC */ 639 hwcfg &= (~HW_CFG_PHY_CLK_SEL_); 640 hwcfg |= HW_CFG_PHY_CLK_SEL_CLK_DIS_; 641 smsc911x_reg_write(pdata, HW_CFG, hwcfg); 642 udelay(10); /* Enough time for clocks to stop */ 643 644 /* Switch to external phy */ 645 hwcfg |= HW_CFG_EXT_PHY_EN_; 646 smsc911x_reg_write(pdata, HW_CFG, hwcfg); 647 648 /* Enable phy clocks to the MAC */ 649 hwcfg &= (~HW_CFG_PHY_CLK_SEL_); 650 hwcfg |= HW_CFG_PHY_CLK_SEL_EXT_PHY_; 651 smsc911x_reg_write(pdata, HW_CFG, hwcfg); 652 udelay(10); /* Enough time for clocks to restart */ 653 654 hwcfg |= HW_CFG_SMI_SEL_; 655 smsc911x_reg_write(pdata, HW_CFG, hwcfg); 656 } 657 658 /* Autodetects and enables external phy if present on supported chips. 659 * autodetection can be overridden by specifying SMSC911X_FORCE_INTERNAL_PHY 660 * or SMSC911X_FORCE_EXTERNAL_PHY in the platform_data flags. */ 661 static void smsc911x_phy_initialise_external(struct smsc911x_data *pdata) 662 { 663 unsigned int hwcfg = smsc911x_reg_read(pdata, HW_CFG); 664 665 if (pdata->config.flags & SMSC911X_FORCE_INTERNAL_PHY) { 666 SMSC_TRACE(pdata, hw, "Forcing internal PHY"); 667 pdata->using_extphy = 0; 668 } else if (pdata->config.flags & SMSC911X_FORCE_EXTERNAL_PHY) { 669 SMSC_TRACE(pdata, hw, "Forcing external PHY"); 670 smsc911x_phy_enable_external(pdata); 671 pdata->using_extphy = 1; 672 } else if (hwcfg & HW_CFG_EXT_PHY_DET_) { 673 SMSC_TRACE(pdata, hw, 674 "HW_CFG EXT_PHY_DET set, using external PHY"); 675 smsc911x_phy_enable_external(pdata); 676 pdata->using_extphy = 1; 677 } else { 678 SMSC_TRACE(pdata, hw, 679 "HW_CFG EXT_PHY_DET clear, using internal PHY"); 680 pdata->using_extphy = 0; 681 } 682 } 683 684 /* Fetches a tx status out of the status fifo */ 685 static unsigned int smsc911x_tx_get_txstatus(struct smsc911x_data *pdata) 686 { 687 unsigned int result = 688 smsc911x_reg_read(pdata, TX_FIFO_INF) & TX_FIFO_INF_TSUSED_; 689 690 if (result != 0) 691 result = smsc911x_reg_read(pdata, TX_STATUS_FIFO); 692 693 return result; 694 } 695 696 /* Fetches the next rx status */ 697 static unsigned int smsc911x_rx_get_rxstatus(struct smsc911x_data *pdata) 698 { 699 unsigned int result = 700 smsc911x_reg_read(pdata, RX_FIFO_INF) & RX_FIFO_INF_RXSUSED_; 701 702 if (result != 0) 703 result = smsc911x_reg_read(pdata, RX_STATUS_FIFO); 704 705 return result; 706 } 707 708 #ifdef USE_PHY_WORK_AROUND 709 static int smsc911x_phy_check_loopbackpkt(struct smsc911x_data *pdata) 710 { 711 unsigned int tries; 712 u32 wrsz; 713 u32 rdsz; 714 ulong bufp; 715 716 for (tries = 0; tries < 10; tries++) { 717 unsigned int txcmd_a; 718 unsigned int txcmd_b; 719 unsigned int status; 720 unsigned int pktlength; 721 unsigned int i; 722 723 /* Zero-out rx packet memory */ 724 memset(pdata->loopback_rx_pkt, 0, MIN_PACKET_SIZE); 725 726 /* Write tx packet to 118 */ 727 txcmd_a = (u32)((ulong)pdata->loopback_tx_pkt & 0x03) << 16; 728 txcmd_a |= TX_CMD_A_FIRST_SEG_ | TX_CMD_A_LAST_SEG_; 729 txcmd_a |= MIN_PACKET_SIZE; 730 731 txcmd_b = MIN_PACKET_SIZE << 16 | MIN_PACKET_SIZE; 732 733 smsc911x_reg_write(pdata, TX_DATA_FIFO, txcmd_a); 734 smsc911x_reg_write(pdata, TX_DATA_FIFO, txcmd_b); 735 736 bufp = (ulong)pdata->loopback_tx_pkt & (~0x3); 737 wrsz = MIN_PACKET_SIZE + 3; 738 wrsz += (u32)((ulong)pdata->loopback_tx_pkt & 0x3); 739 wrsz >>= 2; 740 741 pdata->ops->tx_writefifo(pdata, (unsigned int *)bufp, wrsz); 742 743 /* Wait till transmit is done */ 744 i = 60; 745 do { 746 udelay(5); 747 status = smsc911x_tx_get_txstatus(pdata); 748 } while ((i--) && (!status)); 749 750 if (!status) { 751 SMSC_WARN(pdata, hw, 752 "Failed to transmit during loopback test"); 753 continue; 754 } 755 if (status & TX_STS_ES_) { 756 SMSC_WARN(pdata, hw, 757 "Transmit encountered errors during loopback test"); 758 continue; 759 } 760 761 /* Wait till receive is done */ 762 i = 60; 763 do { 764 udelay(5); 765 status = smsc911x_rx_get_rxstatus(pdata); 766 } while ((i--) && (!status)); 767 768 if (!status) { 769 SMSC_WARN(pdata, hw, 770 "Failed to receive during loopback test"); 771 continue; 772 } 773 if (status & RX_STS_ES_) { 774 SMSC_WARN(pdata, hw, 775 "Receive encountered errors during loopback test"); 776 continue; 777 } 778 779 pktlength = ((status & 0x3FFF0000UL) >> 16); 780 bufp = (ulong)pdata->loopback_rx_pkt; 781 rdsz = pktlength + 3; 782 rdsz += (u32)((ulong)pdata->loopback_rx_pkt & 0x3); 783 rdsz >>= 2; 784 785 pdata->ops->rx_readfifo(pdata, (unsigned int *)bufp, rdsz); 786 787 if (pktlength != (MIN_PACKET_SIZE + 4)) { 788 SMSC_WARN(pdata, hw, "Unexpected packet size " 789 "during loop back test, size=%d, will retry", 790 pktlength); 791 } else { 792 unsigned int j; 793 int mismatch = 0; 794 for (j = 0; j < MIN_PACKET_SIZE; j++) { 795 if (pdata->loopback_tx_pkt[j] 796 != pdata->loopback_rx_pkt[j]) { 797 mismatch = 1; 798 break; 799 } 800 } 801 if (!mismatch) { 802 SMSC_TRACE(pdata, hw, "Successfully verified " 803 "loopback packet"); 804 return 0; 805 } else { 806 SMSC_WARN(pdata, hw, "Data mismatch " 807 "during loop back test, will retry"); 808 } 809 } 810 } 811 812 return -EIO; 813 } 814 815 static int smsc911x_phy_reset(struct smsc911x_data *pdata) 816 { 817 unsigned int temp; 818 unsigned int i = 100000; 819 820 temp = smsc911x_reg_read(pdata, PMT_CTRL); 821 smsc911x_reg_write(pdata, PMT_CTRL, temp | PMT_CTRL_PHY_RST_); 822 do { 823 msleep(1); 824 temp = smsc911x_reg_read(pdata, PMT_CTRL); 825 } while ((i--) && (temp & PMT_CTRL_PHY_RST_)); 826 827 if (unlikely(temp & PMT_CTRL_PHY_RST_)) { 828 SMSC_WARN(pdata, hw, "PHY reset failed to complete"); 829 return -EIO; 830 } 831 /* Extra delay required because the phy may not be completed with 832 * its reset when BMCR_RESET is cleared. Specs say 256 uS is 833 * enough delay but using 1ms here to be safe */ 834 msleep(1); 835 836 return 0; 837 } 838 839 static int smsc911x_phy_loopbacktest(struct net_device *dev) 840 { 841 struct smsc911x_data *pdata = netdev_priv(dev); 842 struct phy_device *phy_dev = dev->phydev; 843 int result = -EIO; 844 unsigned int i, val; 845 unsigned long flags; 846 847 /* Initialise tx packet using broadcast destination address */ 848 eth_broadcast_addr(pdata->loopback_tx_pkt); 849 850 /* Use incrementing source address */ 851 for (i = 6; i < 12; i++) 852 pdata->loopback_tx_pkt[i] = (char)i; 853 854 /* Set length type field */ 855 pdata->loopback_tx_pkt[12] = 0x00; 856 pdata->loopback_tx_pkt[13] = 0x00; 857 858 for (i = 14; i < MIN_PACKET_SIZE; i++) 859 pdata->loopback_tx_pkt[i] = (char)i; 860 861 val = smsc911x_reg_read(pdata, HW_CFG); 862 val &= HW_CFG_TX_FIF_SZ_; 863 val |= HW_CFG_SF_; 864 smsc911x_reg_write(pdata, HW_CFG, val); 865 866 smsc911x_reg_write(pdata, TX_CFG, TX_CFG_TX_ON_); 867 smsc911x_reg_write(pdata, RX_CFG, 868 (u32)((ulong)pdata->loopback_rx_pkt & 0x03) << 8); 869 870 for (i = 0; i < 10; i++) { 871 /* Set PHY to 10/FD, no ANEG, and loopback mode */ 872 smsc911x_mii_write(phy_dev->mdio.bus, phy_dev->mdio.addr, 873 MII_BMCR, BMCR_LOOPBACK | BMCR_FULLDPLX); 874 875 /* Enable MAC tx/rx, FD */ 876 spin_lock_irqsave(&pdata->mac_lock, flags); 877 smsc911x_mac_write(pdata, MAC_CR, MAC_CR_FDPX_ 878 | MAC_CR_TXEN_ | MAC_CR_RXEN_); 879 spin_unlock_irqrestore(&pdata->mac_lock, flags); 880 881 if (smsc911x_phy_check_loopbackpkt(pdata) == 0) { 882 result = 0; 883 break; 884 } 885 pdata->resetcount++; 886 887 /* Disable MAC rx */ 888 spin_lock_irqsave(&pdata->mac_lock, flags); 889 smsc911x_mac_write(pdata, MAC_CR, 0); 890 spin_unlock_irqrestore(&pdata->mac_lock, flags); 891 892 smsc911x_phy_reset(pdata); 893 } 894 895 /* Disable MAC */ 896 spin_lock_irqsave(&pdata->mac_lock, flags); 897 smsc911x_mac_write(pdata, MAC_CR, 0); 898 spin_unlock_irqrestore(&pdata->mac_lock, flags); 899 900 /* Cancel PHY loopback mode */ 901 smsc911x_mii_write(phy_dev->mdio.bus, phy_dev->mdio.addr, MII_BMCR, 0); 902 903 smsc911x_reg_write(pdata, TX_CFG, 0); 904 smsc911x_reg_write(pdata, RX_CFG, 0); 905 906 return result; 907 } 908 #endif /* USE_PHY_WORK_AROUND */ 909 910 static void smsc911x_phy_update_flowcontrol(struct smsc911x_data *pdata) 911 { 912 struct net_device *ndev = pdata->dev; 913 struct phy_device *phy_dev = ndev->phydev; 914 u32 afc = smsc911x_reg_read(pdata, AFC_CFG); 915 u32 flow; 916 unsigned long flags; 917 918 if (phy_dev->duplex == DUPLEX_FULL) { 919 u16 lcladv = phy_read(phy_dev, MII_ADVERTISE); 920 u16 rmtadv = phy_read(phy_dev, MII_LPA); 921 u8 cap = mii_resolve_flowctrl_fdx(lcladv, rmtadv); 922 923 if (cap & FLOW_CTRL_RX) 924 flow = 0xFFFF0002; 925 else 926 flow = 0; 927 928 if (cap & FLOW_CTRL_TX) 929 afc |= 0xF; 930 else 931 afc &= ~0xF; 932 933 SMSC_TRACE(pdata, hw, "rx pause %s, tx pause %s", 934 (cap & FLOW_CTRL_RX ? "enabled" : "disabled"), 935 (cap & FLOW_CTRL_TX ? "enabled" : "disabled")); 936 } else { 937 SMSC_TRACE(pdata, hw, "half duplex"); 938 flow = 0; 939 afc |= 0xF; 940 } 941 942 spin_lock_irqsave(&pdata->mac_lock, flags); 943 smsc911x_mac_write(pdata, FLOW, flow); 944 spin_unlock_irqrestore(&pdata->mac_lock, flags); 945 946 smsc911x_reg_write(pdata, AFC_CFG, afc); 947 } 948 949 /* Update link mode if anything has changed. Called periodically when the 950 * PHY is in polling mode, even if nothing has changed. */ 951 static void smsc911x_phy_adjust_link(struct net_device *dev) 952 { 953 struct smsc911x_data *pdata = netdev_priv(dev); 954 struct phy_device *phy_dev = dev->phydev; 955 unsigned long flags; 956 int carrier; 957 958 if (phy_dev->duplex != pdata->last_duplex) { 959 unsigned int mac_cr; 960 SMSC_TRACE(pdata, hw, "duplex state has changed"); 961 962 spin_lock_irqsave(&pdata->mac_lock, flags); 963 mac_cr = smsc911x_mac_read(pdata, MAC_CR); 964 if (phy_dev->duplex) { 965 SMSC_TRACE(pdata, hw, 966 "configuring for full duplex mode"); 967 mac_cr |= MAC_CR_FDPX_; 968 } else { 969 SMSC_TRACE(pdata, hw, 970 "configuring for half duplex mode"); 971 mac_cr &= ~MAC_CR_FDPX_; 972 } 973 smsc911x_mac_write(pdata, MAC_CR, mac_cr); 974 spin_unlock_irqrestore(&pdata->mac_lock, flags); 975 976 smsc911x_phy_update_flowcontrol(pdata); 977 pdata->last_duplex = phy_dev->duplex; 978 } 979 980 carrier = netif_carrier_ok(dev); 981 if (carrier != pdata->last_carrier) { 982 SMSC_TRACE(pdata, hw, "carrier state has changed"); 983 if (carrier) { 984 SMSC_TRACE(pdata, hw, "configuring for carrier OK"); 985 if ((pdata->gpio_orig_setting & GPIO_CFG_LED1_EN_) && 986 (!pdata->using_extphy)) { 987 /* Restore original GPIO configuration */ 988 pdata->gpio_setting = pdata->gpio_orig_setting; 989 smsc911x_reg_write(pdata, GPIO_CFG, 990 pdata->gpio_setting); 991 } 992 } else { 993 SMSC_TRACE(pdata, hw, "configuring for no carrier"); 994 /* Check global setting that LED1 995 * usage is 10/100 indicator */ 996 pdata->gpio_setting = smsc911x_reg_read(pdata, 997 GPIO_CFG); 998 if ((pdata->gpio_setting & GPIO_CFG_LED1_EN_) && 999 (!pdata->using_extphy)) { 1000 /* Force 10/100 LED off, after saving 1001 * original GPIO configuration */ 1002 pdata->gpio_orig_setting = pdata->gpio_setting; 1003 1004 pdata->gpio_setting &= ~GPIO_CFG_LED1_EN_; 1005 pdata->gpio_setting |= (GPIO_CFG_GPIOBUF0_ 1006 | GPIO_CFG_GPIODIR0_ 1007 | GPIO_CFG_GPIOD0_); 1008 smsc911x_reg_write(pdata, GPIO_CFG, 1009 pdata->gpio_setting); 1010 } 1011 } 1012 pdata->last_carrier = carrier; 1013 } 1014 } 1015 1016 static int smsc911x_mii_probe(struct net_device *dev) 1017 { 1018 struct smsc911x_data *pdata = netdev_priv(dev); 1019 struct phy_device *phydev; 1020 int ret; 1021 1022 /* find the first phy */ 1023 phydev = phy_find_first(pdata->mii_bus); 1024 if (!phydev) { 1025 netdev_err(dev, "no PHY found\n"); 1026 return -ENODEV; 1027 } 1028 1029 SMSC_TRACE(pdata, probe, "PHY: addr %d, phy_id 0x%08X", 1030 phydev->mdio.addr, phydev->phy_id); 1031 1032 ret = phy_connect_direct(dev, phydev, &smsc911x_phy_adjust_link, 1033 pdata->config.phy_interface); 1034 1035 if (ret) { 1036 netdev_err(dev, "Could not attach to PHY\n"); 1037 return ret; 1038 } 1039 1040 phy_attached_info(phydev); 1041 1042 phy_set_max_speed(phydev, SPEED_100); 1043 1044 /* mask with MAC supported features */ 1045 phy_support_asym_pause(phydev); 1046 1047 pdata->last_duplex = -1; 1048 pdata->last_carrier = -1; 1049 1050 #ifdef USE_PHY_WORK_AROUND 1051 if (smsc911x_phy_loopbacktest(dev) < 0) { 1052 SMSC_WARN(pdata, hw, "Failed Loop Back Test"); 1053 phy_disconnect(phydev); 1054 return -ENODEV; 1055 } 1056 SMSC_TRACE(pdata, hw, "Passed Loop Back Test"); 1057 #endif /* USE_PHY_WORK_AROUND */ 1058 1059 SMSC_TRACE(pdata, hw, "phy initialised successfully"); 1060 return 0; 1061 } 1062 1063 static int smsc911x_mii_init(struct platform_device *pdev, 1064 struct net_device *dev) 1065 { 1066 struct smsc911x_data *pdata = netdev_priv(dev); 1067 struct phy_device *phydev; 1068 int err = -ENXIO; 1069 1070 pdata->mii_bus = mdiobus_alloc(); 1071 if (!pdata->mii_bus) { 1072 err = -ENOMEM; 1073 goto err_out_1; 1074 } 1075 1076 pdata->mii_bus->name = SMSC_MDIONAME; 1077 snprintf(pdata->mii_bus->id, MII_BUS_ID_SIZE, "%s-%x", 1078 pdev->name, pdev->id); 1079 pdata->mii_bus->priv = pdata; 1080 pdata->mii_bus->read = smsc911x_mii_read; 1081 pdata->mii_bus->write = smsc911x_mii_write; 1082 1083 pdata->mii_bus->parent = &pdev->dev; 1084 1085 switch (pdata->idrev & 0xFFFF0000) { 1086 case 0x01170000: 1087 case 0x01150000: 1088 case 0x117A0000: 1089 case 0x115A0000: 1090 /* External PHY supported, try to autodetect */ 1091 smsc911x_phy_initialise_external(pdata); 1092 break; 1093 default: 1094 SMSC_TRACE(pdata, hw, "External PHY is not supported, " 1095 "using internal PHY"); 1096 pdata->using_extphy = 0; 1097 break; 1098 } 1099 1100 if (!pdata->using_extphy) { 1101 /* Mask all PHYs except ID 1 (internal) */ 1102 pdata->mii_bus->phy_mask = ~(1 << 1); 1103 } 1104 1105 if (mdiobus_register(pdata->mii_bus)) { 1106 SMSC_WARN(pdata, probe, "Error registering mii bus"); 1107 goto err_out_free_bus_2; 1108 } 1109 1110 phydev = phy_find_first(pdata->mii_bus); 1111 if (phydev) 1112 phydev->mac_managed_pm = true; 1113 1114 return 0; 1115 1116 err_out_free_bus_2: 1117 mdiobus_free(pdata->mii_bus); 1118 err_out_1: 1119 return err; 1120 } 1121 1122 /* Gets the number of tx statuses in the fifo */ 1123 static unsigned int smsc911x_tx_get_txstatcount(struct smsc911x_data *pdata) 1124 { 1125 return (smsc911x_reg_read(pdata, TX_FIFO_INF) 1126 & TX_FIFO_INF_TSUSED_) >> 16; 1127 } 1128 1129 /* Reads tx statuses and increments counters where necessary */ 1130 static void smsc911x_tx_update_txcounters(struct net_device *dev) 1131 { 1132 struct smsc911x_data *pdata = netdev_priv(dev); 1133 unsigned int tx_stat; 1134 1135 while ((tx_stat = smsc911x_tx_get_txstatus(pdata)) != 0) { 1136 if (unlikely(tx_stat & 0x80000000)) { 1137 /* In this driver the packet tag is used as the packet 1138 * length. Since a packet length can never reach the 1139 * size of 0x8000, this bit is reserved. It is worth 1140 * noting that the "reserved bit" in the warning above 1141 * does not reference a hardware defined reserved bit 1142 * but rather a driver defined one. 1143 */ 1144 SMSC_WARN(pdata, hw, "Packet tag reserved bit is high"); 1145 } else { 1146 if (unlikely(tx_stat & TX_STS_ES_)) { 1147 dev->stats.tx_errors++; 1148 } else { 1149 dev->stats.tx_packets++; 1150 dev->stats.tx_bytes += (tx_stat >> 16); 1151 } 1152 if (unlikely(tx_stat & TX_STS_EXCESS_COL_)) { 1153 dev->stats.collisions += 16; 1154 dev->stats.tx_aborted_errors += 1; 1155 } else { 1156 dev->stats.collisions += 1157 ((tx_stat >> 3) & 0xF); 1158 } 1159 if (unlikely(tx_stat & TX_STS_LOST_CARRIER_)) 1160 dev->stats.tx_carrier_errors += 1; 1161 if (unlikely(tx_stat & TX_STS_LATE_COL_)) { 1162 dev->stats.collisions++; 1163 dev->stats.tx_aborted_errors++; 1164 } 1165 } 1166 } 1167 } 1168 1169 /* Increments the Rx error counters */ 1170 static void 1171 smsc911x_rx_counterrors(struct net_device *dev, unsigned int rxstat) 1172 { 1173 int crc_err = 0; 1174 1175 if (unlikely(rxstat & RX_STS_ES_)) { 1176 dev->stats.rx_errors++; 1177 if (unlikely(rxstat & RX_STS_CRC_ERR_)) { 1178 dev->stats.rx_crc_errors++; 1179 crc_err = 1; 1180 } 1181 } 1182 if (likely(!crc_err)) { 1183 if (unlikely((rxstat & RX_STS_FRAME_TYPE_) && 1184 (rxstat & RX_STS_LENGTH_ERR_))) 1185 dev->stats.rx_length_errors++; 1186 if (rxstat & RX_STS_MCAST_) 1187 dev->stats.multicast++; 1188 } 1189 } 1190 1191 /* Quickly dumps bad packets */ 1192 static void 1193 smsc911x_rx_fastforward(struct smsc911x_data *pdata, unsigned int pktwords) 1194 { 1195 if (likely(pktwords >= 4)) { 1196 unsigned int timeout = 500; 1197 unsigned int val; 1198 smsc911x_reg_write(pdata, RX_DP_CTRL, RX_DP_CTRL_RX_FFWD_); 1199 do { 1200 udelay(1); 1201 val = smsc911x_reg_read(pdata, RX_DP_CTRL); 1202 } while ((val & RX_DP_CTRL_RX_FFWD_) && --timeout); 1203 1204 if (unlikely(timeout == 0)) 1205 SMSC_WARN(pdata, hw, "Timed out waiting for " 1206 "RX FFWD to finish, RX_DP_CTRL: 0x%08X", val); 1207 } else { 1208 while (pktwords--) 1209 smsc911x_reg_read(pdata, RX_DATA_FIFO); 1210 } 1211 } 1212 1213 /* NAPI poll function */ 1214 static int smsc911x_poll(struct napi_struct *napi, int budget) 1215 { 1216 struct smsc911x_data *pdata = 1217 container_of(napi, struct smsc911x_data, napi); 1218 struct net_device *dev = pdata->dev; 1219 int npackets = 0; 1220 1221 while (npackets < budget) { 1222 unsigned int pktlength; 1223 unsigned int pktwords; 1224 struct sk_buff *skb; 1225 unsigned int rxstat = smsc911x_rx_get_rxstatus(pdata); 1226 1227 if (!rxstat) { 1228 unsigned int temp; 1229 /* We processed all packets available. Tell NAPI it can 1230 * stop polling then re-enable rx interrupts */ 1231 smsc911x_reg_write(pdata, INT_STS, INT_STS_RSFL_); 1232 napi_complete(napi); 1233 temp = smsc911x_reg_read(pdata, INT_EN); 1234 temp |= INT_EN_RSFL_EN_; 1235 smsc911x_reg_write(pdata, INT_EN, temp); 1236 break; 1237 } 1238 1239 /* Count packet for NAPI scheduling, even if it has an error. 1240 * Error packets still require cycles to discard */ 1241 npackets++; 1242 1243 pktlength = ((rxstat & 0x3FFF0000) >> 16); 1244 pktwords = (pktlength + NET_IP_ALIGN + 3) >> 2; 1245 smsc911x_rx_counterrors(dev, rxstat); 1246 1247 if (unlikely(rxstat & RX_STS_ES_)) { 1248 SMSC_WARN(pdata, rx_err, 1249 "Discarding packet with error bit set"); 1250 /* Packet has an error, discard it and continue with 1251 * the next */ 1252 smsc911x_rx_fastforward(pdata, pktwords); 1253 dev->stats.rx_dropped++; 1254 continue; 1255 } 1256 1257 skb = netdev_alloc_skb(dev, pktwords << 2); 1258 if (unlikely(!skb)) { 1259 SMSC_WARN(pdata, rx_err, 1260 "Unable to allocate skb for rx packet"); 1261 /* Drop the packet and stop this polling iteration */ 1262 smsc911x_rx_fastforward(pdata, pktwords); 1263 dev->stats.rx_dropped++; 1264 break; 1265 } 1266 1267 pdata->ops->rx_readfifo(pdata, 1268 (unsigned int *)skb->data, pktwords); 1269 1270 /* Align IP on 16B boundary */ 1271 skb_reserve(skb, NET_IP_ALIGN); 1272 skb_put(skb, pktlength - 4); 1273 skb->protocol = eth_type_trans(skb, dev); 1274 skb_checksum_none_assert(skb); 1275 netif_receive_skb(skb); 1276 1277 /* Update counters */ 1278 dev->stats.rx_packets++; 1279 dev->stats.rx_bytes += (pktlength - 4); 1280 } 1281 1282 /* Return total received packets */ 1283 return npackets; 1284 } 1285 1286 /* Returns hash bit number for given MAC address 1287 * Example: 1288 * 01 00 5E 00 00 01 -> returns bit number 31 */ 1289 static unsigned int smsc911x_hash(char addr[ETH_ALEN]) 1290 { 1291 return (ether_crc(ETH_ALEN, addr) >> 26) & 0x3f; 1292 } 1293 1294 static void smsc911x_rx_multicast_update(struct smsc911x_data *pdata) 1295 { 1296 /* Performs the multicast & mac_cr update. This is called when 1297 * safe on the current hardware, and with the mac_lock held */ 1298 unsigned int mac_cr; 1299 1300 SMSC_ASSERT_MAC_LOCK(pdata); 1301 1302 mac_cr = smsc911x_mac_read(pdata, MAC_CR); 1303 mac_cr |= pdata->set_bits_mask; 1304 mac_cr &= ~(pdata->clear_bits_mask); 1305 smsc911x_mac_write(pdata, MAC_CR, mac_cr); 1306 smsc911x_mac_write(pdata, HASHH, pdata->hashhi); 1307 smsc911x_mac_write(pdata, HASHL, pdata->hashlo); 1308 SMSC_TRACE(pdata, hw, "maccr 0x%08X, HASHH 0x%08X, HASHL 0x%08X", 1309 mac_cr, pdata->hashhi, pdata->hashlo); 1310 } 1311 1312 static void smsc911x_rx_multicast_update_workaround(struct smsc911x_data *pdata) 1313 { 1314 unsigned int mac_cr; 1315 1316 /* This function is only called for older LAN911x devices 1317 * (revA or revB), where MAC_CR, HASHH and HASHL should not 1318 * be modified during Rx - newer devices immediately update the 1319 * registers. 1320 * 1321 * This is called from interrupt context */ 1322 1323 spin_lock(&pdata->mac_lock); 1324 1325 /* Check Rx has stopped */ 1326 if (smsc911x_mac_read(pdata, MAC_CR) & MAC_CR_RXEN_) 1327 SMSC_WARN(pdata, drv, "Rx not stopped"); 1328 1329 /* Perform the update - safe to do now Rx has stopped */ 1330 smsc911x_rx_multicast_update(pdata); 1331 1332 /* Re-enable Rx */ 1333 mac_cr = smsc911x_mac_read(pdata, MAC_CR); 1334 mac_cr |= MAC_CR_RXEN_; 1335 smsc911x_mac_write(pdata, MAC_CR, mac_cr); 1336 1337 pdata->multicast_update_pending = 0; 1338 1339 spin_unlock(&pdata->mac_lock); 1340 } 1341 1342 static int smsc911x_phy_general_power_up(struct smsc911x_data *pdata) 1343 { 1344 struct net_device *ndev = pdata->dev; 1345 struct phy_device *phy_dev = ndev->phydev; 1346 int rc = 0; 1347 1348 if (!phy_dev) 1349 return rc; 1350 1351 /* If the internal PHY is in General Power-Down mode, all, except the 1352 * management interface, is powered-down and stays in that condition as 1353 * long as Phy register bit 0.11 is HIGH. 1354 * 1355 * In that case, clear the bit 0.11, so the PHY powers up and we can 1356 * access to the phy registers. 1357 */ 1358 rc = phy_read(phy_dev, MII_BMCR); 1359 if (rc < 0) { 1360 SMSC_WARN(pdata, drv, "Failed reading PHY control reg"); 1361 return rc; 1362 } 1363 1364 /* If the PHY general power-down bit is not set is not necessary to 1365 * disable the general power down-mode. 1366 */ 1367 if (rc & BMCR_PDOWN) { 1368 rc = phy_write(phy_dev, MII_BMCR, rc & ~BMCR_PDOWN); 1369 if (rc < 0) { 1370 SMSC_WARN(pdata, drv, "Failed writing PHY control reg"); 1371 return rc; 1372 } 1373 1374 usleep_range(1000, 1500); 1375 } 1376 1377 return 0; 1378 } 1379 1380 static int smsc911x_phy_disable_energy_detect(struct smsc911x_data *pdata) 1381 { 1382 struct net_device *ndev = pdata->dev; 1383 struct phy_device *phy_dev = ndev->phydev; 1384 int rc = 0; 1385 1386 if (!phy_dev) 1387 return rc; 1388 1389 rc = phy_read(phy_dev, MII_LAN83C185_CTRL_STATUS); 1390 1391 if (rc < 0) { 1392 SMSC_WARN(pdata, drv, "Failed reading PHY control reg"); 1393 return rc; 1394 } 1395 1396 /* Only disable if energy detect mode is already enabled */ 1397 if (rc & MII_LAN83C185_EDPWRDOWN) { 1398 /* Disable energy detect mode for this SMSC Transceivers */ 1399 rc = phy_write(phy_dev, MII_LAN83C185_CTRL_STATUS, 1400 rc & (~MII_LAN83C185_EDPWRDOWN)); 1401 1402 if (rc < 0) { 1403 SMSC_WARN(pdata, drv, "Failed writing PHY control reg"); 1404 return rc; 1405 } 1406 /* Allow PHY to wakeup */ 1407 mdelay(2); 1408 } 1409 1410 return 0; 1411 } 1412 1413 static int smsc911x_phy_enable_energy_detect(struct smsc911x_data *pdata) 1414 { 1415 struct net_device *ndev = pdata->dev; 1416 struct phy_device *phy_dev = ndev->phydev; 1417 int rc = 0; 1418 1419 if (!phy_dev) 1420 return rc; 1421 1422 rc = phy_read(phy_dev, MII_LAN83C185_CTRL_STATUS); 1423 1424 if (rc < 0) { 1425 SMSC_WARN(pdata, drv, "Failed reading PHY control reg"); 1426 return rc; 1427 } 1428 1429 /* Only enable if energy detect mode is already disabled */ 1430 if (!(rc & MII_LAN83C185_EDPWRDOWN)) { 1431 /* Enable energy detect mode for this SMSC Transceivers */ 1432 rc = phy_write(phy_dev, MII_LAN83C185_CTRL_STATUS, 1433 rc | MII_LAN83C185_EDPWRDOWN); 1434 1435 if (rc < 0) { 1436 SMSC_WARN(pdata, drv, "Failed writing PHY control reg"); 1437 return rc; 1438 } 1439 } 1440 return 0; 1441 } 1442 1443 static int smsc911x_soft_reset(struct smsc911x_data *pdata) 1444 { 1445 unsigned int timeout; 1446 unsigned int temp; 1447 int ret; 1448 unsigned int reset_offset = HW_CFG; 1449 unsigned int reset_mask = HW_CFG_SRST_; 1450 1451 /* 1452 * Make sure to power-up the PHY chip before doing a reset, otherwise 1453 * the reset fails. 1454 */ 1455 ret = smsc911x_phy_general_power_up(pdata); 1456 if (ret) { 1457 SMSC_WARN(pdata, drv, "Failed to power-up the PHY chip"); 1458 return ret; 1459 } 1460 1461 /* 1462 * LAN9210/LAN9211/LAN9220/LAN9221 chips have an internal PHY that 1463 * are initialized in a Energy Detect Power-Down mode that prevents 1464 * the MAC chip to be software reseted. So we have to wakeup the PHY 1465 * before. 1466 */ 1467 if (pdata->generation == 4) { 1468 ret = smsc911x_phy_disable_energy_detect(pdata); 1469 1470 if (ret) { 1471 SMSC_WARN(pdata, drv, "Failed to wakeup the PHY chip"); 1472 return ret; 1473 } 1474 } 1475 1476 if ((pdata->idrev & 0xFFFF0000) == LAN9250) { 1477 /* special reset for LAN9250 */ 1478 reset_offset = RESET_CTL; 1479 reset_mask = RESET_CTL_DIGITAL_RST_; 1480 } 1481 1482 /* Reset the LAN911x */ 1483 smsc911x_reg_write(pdata, reset_offset, reset_mask); 1484 1485 /* verify reset bit is cleared */ 1486 timeout = 10; 1487 do { 1488 udelay(10); 1489 temp = smsc911x_reg_read(pdata, reset_offset); 1490 } while ((--timeout) && (temp & reset_mask)); 1491 1492 if (unlikely(temp & reset_mask)) { 1493 SMSC_WARN(pdata, drv, "Failed to complete reset"); 1494 return -EIO; 1495 } 1496 1497 if (pdata->generation == 4) { 1498 ret = smsc911x_phy_enable_energy_detect(pdata); 1499 1500 if (ret) { 1501 SMSC_WARN(pdata, drv, "Failed to wakeup the PHY chip"); 1502 return ret; 1503 } 1504 } 1505 1506 return 0; 1507 } 1508 1509 /* Sets the device MAC address to dev_addr, called with mac_lock held */ 1510 static void 1511 smsc911x_set_hw_mac_address(struct smsc911x_data *pdata, const u8 dev_addr[6]) 1512 { 1513 u32 mac_high16 = (dev_addr[5] << 8) | dev_addr[4]; 1514 u32 mac_low32 = (dev_addr[3] << 24) | (dev_addr[2] << 16) | 1515 (dev_addr[1] << 8) | dev_addr[0]; 1516 1517 SMSC_ASSERT_MAC_LOCK(pdata); 1518 1519 smsc911x_mac_write(pdata, ADDRH, mac_high16); 1520 smsc911x_mac_write(pdata, ADDRL, mac_low32); 1521 } 1522 1523 static void smsc911x_disable_irq_chip(struct net_device *dev) 1524 { 1525 struct smsc911x_data *pdata = netdev_priv(dev); 1526 1527 smsc911x_reg_write(pdata, INT_EN, 0); 1528 smsc911x_reg_write(pdata, INT_STS, 0xFFFFFFFF); 1529 } 1530 1531 static irqreturn_t smsc911x_irqhandler(int irq, void *dev_id) 1532 { 1533 struct net_device *dev = dev_id; 1534 struct smsc911x_data *pdata = netdev_priv(dev); 1535 u32 intsts = smsc911x_reg_read(pdata, INT_STS); 1536 u32 inten = smsc911x_reg_read(pdata, INT_EN); 1537 int serviced = IRQ_NONE; 1538 u32 temp; 1539 1540 if (unlikely(intsts & inten & INT_STS_SW_INT_)) { 1541 temp = smsc911x_reg_read(pdata, INT_EN); 1542 temp &= (~INT_EN_SW_INT_EN_); 1543 smsc911x_reg_write(pdata, INT_EN, temp); 1544 smsc911x_reg_write(pdata, INT_STS, INT_STS_SW_INT_); 1545 pdata->software_irq_signal = 1; 1546 smp_wmb(); 1547 serviced = IRQ_HANDLED; 1548 } 1549 1550 if (unlikely(intsts & inten & INT_STS_RXSTOP_INT_)) { 1551 /* Called when there is a multicast update scheduled and 1552 * it is now safe to complete the update */ 1553 SMSC_TRACE(pdata, intr, "RX Stop interrupt"); 1554 smsc911x_reg_write(pdata, INT_STS, INT_STS_RXSTOP_INT_); 1555 if (pdata->multicast_update_pending) 1556 smsc911x_rx_multicast_update_workaround(pdata); 1557 serviced = IRQ_HANDLED; 1558 } 1559 1560 if (intsts & inten & INT_STS_TDFA_) { 1561 temp = smsc911x_reg_read(pdata, FIFO_INT); 1562 temp |= FIFO_INT_TX_AVAIL_LEVEL_; 1563 smsc911x_reg_write(pdata, FIFO_INT, temp); 1564 smsc911x_reg_write(pdata, INT_STS, INT_STS_TDFA_); 1565 netif_wake_queue(dev); 1566 serviced = IRQ_HANDLED; 1567 } 1568 1569 if (unlikely(intsts & inten & INT_STS_RXE_)) { 1570 SMSC_TRACE(pdata, intr, "RX Error interrupt"); 1571 smsc911x_reg_write(pdata, INT_STS, INT_STS_RXE_); 1572 serviced = IRQ_HANDLED; 1573 } 1574 1575 if (likely(intsts & inten & INT_STS_RSFL_)) { 1576 if (likely(napi_schedule_prep(&pdata->napi))) { 1577 /* Disable Rx interrupts */ 1578 temp = smsc911x_reg_read(pdata, INT_EN); 1579 temp &= (~INT_EN_RSFL_EN_); 1580 smsc911x_reg_write(pdata, INT_EN, temp); 1581 /* Schedule a NAPI poll */ 1582 __napi_schedule(&pdata->napi); 1583 } else { 1584 SMSC_WARN(pdata, rx_err, "napi_schedule_prep failed"); 1585 } 1586 serviced = IRQ_HANDLED; 1587 } 1588 1589 return serviced; 1590 } 1591 1592 static int smsc911x_open(struct net_device *dev) 1593 { 1594 struct smsc911x_data *pdata = netdev_priv(dev); 1595 unsigned int timeout; 1596 unsigned int temp; 1597 unsigned int intcfg; 1598 int retval; 1599 int irq_flags; 1600 1601 pm_runtime_get_sync(dev->dev.parent); 1602 1603 /* find and start the given phy */ 1604 if (!dev->phydev) { 1605 retval = smsc911x_mii_probe(dev); 1606 if (retval < 0) { 1607 SMSC_WARN(pdata, probe, "Error starting phy"); 1608 goto out; 1609 } 1610 } 1611 1612 /* Reset the LAN911x */ 1613 retval = smsc911x_soft_reset(pdata); 1614 if (retval) { 1615 SMSC_WARN(pdata, hw, "soft reset failed"); 1616 goto mii_free_out; 1617 } 1618 1619 smsc911x_reg_write(pdata, HW_CFG, 0x00050000); 1620 smsc911x_reg_write(pdata, AFC_CFG, 0x006E3740); 1621 1622 /* Increase the legal frame size of VLAN tagged frames to 1522 bytes */ 1623 spin_lock_irq(&pdata->mac_lock); 1624 smsc911x_mac_write(pdata, VLAN1, ETH_P_8021Q); 1625 spin_unlock_irq(&pdata->mac_lock); 1626 1627 /* Make sure EEPROM has finished loading before setting GPIO_CFG */ 1628 timeout = 50; 1629 while ((smsc911x_reg_read(pdata, E2P_CMD) & E2P_CMD_EPC_BUSY_) && 1630 --timeout) { 1631 udelay(10); 1632 } 1633 1634 if (unlikely(timeout == 0)) 1635 SMSC_WARN(pdata, ifup, 1636 "Timed out waiting for EEPROM busy bit to clear"); 1637 1638 smsc911x_reg_write(pdata, GPIO_CFG, 0x70070000); 1639 1640 /* The soft reset above cleared the device's MAC address, 1641 * restore it from local copy (set in probe) */ 1642 spin_lock_irq(&pdata->mac_lock); 1643 smsc911x_set_hw_mac_address(pdata, dev->dev_addr); 1644 spin_unlock_irq(&pdata->mac_lock); 1645 1646 /* Initialise irqs, but leave all sources disabled */ 1647 smsc911x_disable_irq_chip(dev); 1648 1649 /* Set interrupt deassertion to 100uS */ 1650 intcfg = ((10 << 24) | INT_CFG_IRQ_EN_); 1651 1652 if (pdata->config.irq_polarity) { 1653 SMSC_TRACE(pdata, ifup, "irq polarity: active high"); 1654 intcfg |= INT_CFG_IRQ_POL_; 1655 } else { 1656 SMSC_TRACE(pdata, ifup, "irq polarity: active low"); 1657 } 1658 1659 if (pdata->config.irq_type) { 1660 SMSC_TRACE(pdata, ifup, "irq type: push-pull"); 1661 intcfg |= INT_CFG_IRQ_TYPE_; 1662 } else { 1663 SMSC_TRACE(pdata, ifup, "irq type: open drain"); 1664 } 1665 1666 smsc911x_reg_write(pdata, INT_CFG, intcfg); 1667 1668 SMSC_TRACE(pdata, ifup, "Testing irq handler using IRQ %d", dev->irq); 1669 pdata->software_irq_signal = 0; 1670 smp_wmb(); 1671 1672 irq_flags = irq_get_trigger_type(dev->irq); 1673 retval = request_irq(dev->irq, smsc911x_irqhandler, 1674 irq_flags | IRQF_SHARED, dev->name, dev); 1675 if (retval) { 1676 SMSC_WARN(pdata, probe, 1677 "Unable to claim requested irq: %d", dev->irq); 1678 goto mii_free_out; 1679 } 1680 1681 temp = smsc911x_reg_read(pdata, INT_EN); 1682 temp |= INT_EN_SW_INT_EN_; 1683 smsc911x_reg_write(pdata, INT_EN, temp); 1684 1685 timeout = 1000; 1686 while (timeout--) { 1687 if (pdata->software_irq_signal) 1688 break; 1689 msleep(1); 1690 } 1691 1692 if (!pdata->software_irq_signal) { 1693 netdev_warn(dev, "ISR failed signaling test (IRQ %d)\n", 1694 dev->irq); 1695 retval = -ENODEV; 1696 goto irq_stop_out; 1697 } 1698 SMSC_TRACE(pdata, ifup, "IRQ handler passed test using IRQ %d", 1699 dev->irq); 1700 1701 netdev_info(dev, "SMSC911x/921x identified at %#08lx, IRQ: %d\n", 1702 (unsigned long)pdata->ioaddr, dev->irq); 1703 1704 /* Reset the last known duplex and carrier */ 1705 pdata->last_duplex = -1; 1706 pdata->last_carrier = -1; 1707 1708 /* Bring the PHY up */ 1709 phy_start(dev->phydev); 1710 1711 temp = smsc911x_reg_read(pdata, HW_CFG); 1712 /* Preserve TX FIFO size and external PHY configuration */ 1713 temp &= (HW_CFG_TX_FIF_SZ_|0x00000FFF); 1714 temp |= HW_CFG_SF_; 1715 smsc911x_reg_write(pdata, HW_CFG, temp); 1716 1717 temp = smsc911x_reg_read(pdata, FIFO_INT); 1718 temp |= FIFO_INT_TX_AVAIL_LEVEL_; 1719 temp &= ~(FIFO_INT_RX_STS_LEVEL_); 1720 smsc911x_reg_write(pdata, FIFO_INT, temp); 1721 1722 /* set RX Data offset to 2 bytes for alignment */ 1723 smsc911x_reg_write(pdata, RX_CFG, (NET_IP_ALIGN << 8)); 1724 1725 /* enable NAPI polling before enabling RX interrupts */ 1726 napi_enable(&pdata->napi); 1727 1728 temp = smsc911x_reg_read(pdata, INT_EN); 1729 temp |= (INT_EN_TDFA_EN_ | INT_EN_RSFL_EN_ | INT_EN_RXSTOP_INT_EN_); 1730 smsc911x_reg_write(pdata, INT_EN, temp); 1731 1732 spin_lock_irq(&pdata->mac_lock); 1733 temp = smsc911x_mac_read(pdata, MAC_CR); 1734 temp |= (MAC_CR_TXEN_ | MAC_CR_RXEN_ | MAC_CR_HBDIS_); 1735 smsc911x_mac_write(pdata, MAC_CR, temp); 1736 spin_unlock_irq(&pdata->mac_lock); 1737 1738 smsc911x_reg_write(pdata, TX_CFG, TX_CFG_TX_ON_); 1739 1740 netif_start_queue(dev); 1741 return 0; 1742 1743 irq_stop_out: 1744 free_irq(dev->irq, dev); 1745 mii_free_out: 1746 phy_disconnect(dev->phydev); 1747 out: 1748 pm_runtime_put(dev->dev.parent); 1749 return retval; 1750 } 1751 1752 /* Entry point for stopping the interface */ 1753 static int smsc911x_stop(struct net_device *dev) 1754 { 1755 struct smsc911x_data *pdata = netdev_priv(dev); 1756 unsigned int temp; 1757 1758 /* Disable all device interrupts */ 1759 temp = smsc911x_reg_read(pdata, INT_CFG); 1760 temp &= ~INT_CFG_IRQ_EN_; 1761 smsc911x_reg_write(pdata, INT_CFG, temp); 1762 1763 /* Stop Tx and Rx polling */ 1764 netif_stop_queue(dev); 1765 napi_disable(&pdata->napi); 1766 1767 /* At this point all Rx and Tx activity is stopped */ 1768 dev->stats.rx_dropped += smsc911x_reg_read(pdata, RX_DROP); 1769 smsc911x_tx_update_txcounters(dev); 1770 1771 free_irq(dev->irq, dev); 1772 1773 /* Bring the PHY down */ 1774 if (dev->phydev) { 1775 phy_stop(dev->phydev); 1776 phy_disconnect(dev->phydev); 1777 } 1778 netif_carrier_off(dev); 1779 pm_runtime_put(dev->dev.parent); 1780 1781 SMSC_TRACE(pdata, ifdown, "Interface stopped"); 1782 return 0; 1783 } 1784 1785 /* Entry point for transmitting a packet */ 1786 static netdev_tx_t 1787 smsc911x_hard_start_xmit(struct sk_buff *skb, struct net_device *dev) 1788 { 1789 struct smsc911x_data *pdata = netdev_priv(dev); 1790 unsigned int freespace; 1791 unsigned int tx_cmd_a; 1792 unsigned int tx_cmd_b; 1793 unsigned int temp; 1794 u32 wrsz; 1795 ulong bufp; 1796 1797 freespace = smsc911x_reg_read(pdata, TX_FIFO_INF) & TX_FIFO_INF_TDFREE_; 1798 1799 if (unlikely(freespace < TX_FIFO_LOW_THRESHOLD)) 1800 SMSC_WARN(pdata, tx_err, 1801 "Tx data fifo low, space available: %d", freespace); 1802 1803 /* Word alignment adjustment */ 1804 tx_cmd_a = (u32)((ulong)skb->data & 0x03) << 16; 1805 tx_cmd_a |= TX_CMD_A_FIRST_SEG_ | TX_CMD_A_LAST_SEG_; 1806 tx_cmd_a |= (unsigned int)skb->len; 1807 1808 tx_cmd_b = ((unsigned int)skb->len) << 16; 1809 tx_cmd_b |= (unsigned int)skb->len; 1810 1811 smsc911x_reg_write(pdata, TX_DATA_FIFO, tx_cmd_a); 1812 smsc911x_reg_write(pdata, TX_DATA_FIFO, tx_cmd_b); 1813 1814 bufp = (ulong)skb->data & (~0x3); 1815 wrsz = (u32)skb->len + 3; 1816 wrsz += (u32)((ulong)skb->data & 0x3); 1817 wrsz >>= 2; 1818 1819 pdata->ops->tx_writefifo(pdata, (unsigned int *)bufp, wrsz); 1820 freespace -= (skb->len + 32); 1821 skb_tx_timestamp(skb); 1822 dev_consume_skb_any(skb); 1823 1824 if (unlikely(smsc911x_tx_get_txstatcount(pdata) >= 30)) 1825 smsc911x_tx_update_txcounters(dev); 1826 1827 if (freespace < TX_FIFO_LOW_THRESHOLD) { 1828 netif_stop_queue(dev); 1829 temp = smsc911x_reg_read(pdata, FIFO_INT); 1830 temp &= 0x00FFFFFF; 1831 temp |= 0x32000000; 1832 smsc911x_reg_write(pdata, FIFO_INT, temp); 1833 } 1834 1835 return NETDEV_TX_OK; 1836 } 1837 1838 /* Entry point for getting status counters */ 1839 static struct net_device_stats *smsc911x_get_stats(struct net_device *dev) 1840 { 1841 struct smsc911x_data *pdata = netdev_priv(dev); 1842 smsc911x_tx_update_txcounters(dev); 1843 dev->stats.rx_dropped += smsc911x_reg_read(pdata, RX_DROP); 1844 return &dev->stats; 1845 } 1846 1847 /* Entry point for setting addressing modes */ 1848 static void smsc911x_set_multicast_list(struct net_device *dev) 1849 { 1850 struct smsc911x_data *pdata = netdev_priv(dev); 1851 unsigned long flags; 1852 1853 if (dev->flags & IFF_PROMISC) { 1854 /* Enabling promiscuous mode */ 1855 pdata->set_bits_mask = MAC_CR_PRMS_; 1856 pdata->clear_bits_mask = (MAC_CR_MCPAS_ | MAC_CR_HPFILT_); 1857 pdata->hashhi = 0; 1858 pdata->hashlo = 0; 1859 } else if (dev->flags & IFF_ALLMULTI) { 1860 /* Enabling all multicast mode */ 1861 pdata->set_bits_mask = MAC_CR_MCPAS_; 1862 pdata->clear_bits_mask = (MAC_CR_PRMS_ | MAC_CR_HPFILT_); 1863 pdata->hashhi = 0; 1864 pdata->hashlo = 0; 1865 } else if (!netdev_mc_empty(dev)) { 1866 /* Enabling specific multicast addresses */ 1867 unsigned int hash_high = 0; 1868 unsigned int hash_low = 0; 1869 struct netdev_hw_addr *ha; 1870 1871 pdata->set_bits_mask = MAC_CR_HPFILT_; 1872 pdata->clear_bits_mask = (MAC_CR_PRMS_ | MAC_CR_MCPAS_); 1873 1874 netdev_for_each_mc_addr(ha, dev) { 1875 unsigned int bitnum = smsc911x_hash(ha->addr); 1876 unsigned int mask = 0x01 << (bitnum & 0x1F); 1877 1878 if (bitnum & 0x20) 1879 hash_high |= mask; 1880 else 1881 hash_low |= mask; 1882 } 1883 1884 pdata->hashhi = hash_high; 1885 pdata->hashlo = hash_low; 1886 } else { 1887 /* Enabling local MAC address only */ 1888 pdata->set_bits_mask = 0; 1889 pdata->clear_bits_mask = 1890 (MAC_CR_PRMS_ | MAC_CR_MCPAS_ | MAC_CR_HPFILT_); 1891 pdata->hashhi = 0; 1892 pdata->hashlo = 0; 1893 } 1894 1895 spin_lock_irqsave(&pdata->mac_lock, flags); 1896 1897 if (pdata->generation <= 1) { 1898 /* Older hardware revision - cannot change these flags while 1899 * receiving data */ 1900 if (!pdata->multicast_update_pending) { 1901 unsigned int temp; 1902 SMSC_TRACE(pdata, hw, "scheduling mcast update"); 1903 pdata->multicast_update_pending = 1; 1904 1905 /* Request the hardware to stop, then perform the 1906 * update when we get an RX_STOP interrupt */ 1907 temp = smsc911x_mac_read(pdata, MAC_CR); 1908 temp &= ~(MAC_CR_RXEN_); 1909 smsc911x_mac_write(pdata, MAC_CR, temp); 1910 } else { 1911 /* There is another update pending, this should now 1912 * use the newer values */ 1913 } 1914 } else { 1915 /* Newer hardware revision - can write immediately */ 1916 smsc911x_rx_multicast_update(pdata); 1917 } 1918 1919 spin_unlock_irqrestore(&pdata->mac_lock, flags); 1920 } 1921 1922 #ifdef CONFIG_NET_POLL_CONTROLLER 1923 static void smsc911x_poll_controller(struct net_device *dev) 1924 { 1925 disable_irq(dev->irq); 1926 smsc911x_irqhandler(0, dev); 1927 enable_irq(dev->irq); 1928 } 1929 #endif /* CONFIG_NET_POLL_CONTROLLER */ 1930 1931 static int smsc911x_set_mac_address(struct net_device *dev, void *p) 1932 { 1933 struct smsc911x_data *pdata = netdev_priv(dev); 1934 struct sockaddr *addr = p; 1935 1936 /* On older hardware revisions we cannot change the mac address 1937 * registers while receiving data. Newer devices can safely change 1938 * this at any time. */ 1939 if (pdata->generation <= 1 && netif_running(dev)) 1940 return -EBUSY; 1941 1942 if (!is_valid_ether_addr(addr->sa_data)) 1943 return -EADDRNOTAVAIL; 1944 1945 eth_hw_addr_set(dev, addr->sa_data); 1946 1947 spin_lock_irq(&pdata->mac_lock); 1948 smsc911x_set_hw_mac_address(pdata, dev->dev_addr); 1949 spin_unlock_irq(&pdata->mac_lock); 1950 1951 netdev_info(dev, "MAC Address: %pM\n", dev->dev_addr); 1952 1953 return 0; 1954 } 1955 1956 static void smsc911x_ethtool_getdrvinfo(struct net_device *dev, 1957 struct ethtool_drvinfo *info) 1958 { 1959 strscpy(info->driver, SMSC_CHIPNAME, sizeof(info->driver)); 1960 strscpy(info->version, SMSC_DRV_VERSION, sizeof(info->version)); 1961 strscpy(info->bus_info, dev_name(dev->dev.parent), 1962 sizeof(info->bus_info)); 1963 } 1964 1965 static u32 smsc911x_ethtool_getmsglevel(struct net_device *dev) 1966 { 1967 struct smsc911x_data *pdata = netdev_priv(dev); 1968 return pdata->msg_enable; 1969 } 1970 1971 static void smsc911x_ethtool_setmsglevel(struct net_device *dev, u32 level) 1972 { 1973 struct smsc911x_data *pdata = netdev_priv(dev); 1974 pdata->msg_enable = level; 1975 } 1976 1977 static int smsc911x_ethtool_getregslen(struct net_device *dev) 1978 { 1979 return (((E2P_DATA - ID_REV) / 4 + 1) + (WUCSR - MAC_CR) + 1 + 32) * 1980 sizeof(u32); 1981 } 1982 1983 static void 1984 smsc911x_ethtool_getregs(struct net_device *dev, struct ethtool_regs *regs, 1985 void *buf) 1986 { 1987 struct smsc911x_data *pdata = netdev_priv(dev); 1988 struct phy_device *phy_dev = dev->phydev; 1989 unsigned long flags; 1990 unsigned int i; 1991 unsigned int j = 0; 1992 u32 *data = buf; 1993 1994 regs->version = pdata->idrev; 1995 for (i = ID_REV; i <= E2P_DATA; i += (sizeof(u32))) 1996 data[j++] = smsc911x_reg_read(pdata, i); 1997 1998 for (i = MAC_CR; i <= WUCSR; i++) { 1999 spin_lock_irqsave(&pdata->mac_lock, flags); 2000 data[j++] = smsc911x_mac_read(pdata, i); 2001 spin_unlock_irqrestore(&pdata->mac_lock, flags); 2002 } 2003 2004 for (i = 0; i <= 31; i++) 2005 data[j++] = smsc911x_mii_read(phy_dev->mdio.bus, 2006 phy_dev->mdio.addr, i); 2007 } 2008 2009 static void smsc911x_eeprom_enable_access(struct smsc911x_data *pdata) 2010 { 2011 unsigned int temp = smsc911x_reg_read(pdata, GPIO_CFG); 2012 temp &= ~GPIO_CFG_EEPR_EN_; 2013 smsc911x_reg_write(pdata, GPIO_CFG, temp); 2014 msleep(1); 2015 } 2016 2017 static int smsc911x_eeprom_send_cmd(struct smsc911x_data *pdata, u32 op) 2018 { 2019 int timeout = 100; 2020 u32 e2cmd; 2021 2022 SMSC_TRACE(pdata, drv, "op 0x%08x", op); 2023 if (smsc911x_reg_read(pdata, E2P_CMD) & E2P_CMD_EPC_BUSY_) { 2024 SMSC_WARN(pdata, drv, "Busy at start"); 2025 return -EBUSY; 2026 } 2027 2028 e2cmd = op | E2P_CMD_EPC_BUSY_; 2029 smsc911x_reg_write(pdata, E2P_CMD, e2cmd); 2030 2031 do { 2032 msleep(1); 2033 e2cmd = smsc911x_reg_read(pdata, E2P_CMD); 2034 } while ((e2cmd & E2P_CMD_EPC_BUSY_) && (--timeout)); 2035 2036 if (!timeout) { 2037 SMSC_TRACE(pdata, drv, "TIMED OUT"); 2038 return -EAGAIN; 2039 } 2040 2041 if (e2cmd & E2P_CMD_EPC_TIMEOUT_) { 2042 SMSC_TRACE(pdata, drv, "Error occurred during eeprom operation"); 2043 return -EINVAL; 2044 } 2045 2046 return 0; 2047 } 2048 2049 static int smsc911x_eeprom_read_location(struct smsc911x_data *pdata, 2050 u8 address, u8 *data) 2051 { 2052 u32 op = E2P_CMD_EPC_CMD_READ_ | address; 2053 int ret; 2054 2055 SMSC_TRACE(pdata, drv, "address 0x%x", address); 2056 ret = smsc911x_eeprom_send_cmd(pdata, op); 2057 2058 if (!ret) 2059 data[address] = smsc911x_reg_read(pdata, E2P_DATA); 2060 2061 return ret; 2062 } 2063 2064 static int smsc911x_eeprom_write_location(struct smsc911x_data *pdata, 2065 u8 address, u8 data) 2066 { 2067 u32 op = E2P_CMD_EPC_CMD_ERASE_ | address; 2068 int ret; 2069 2070 SMSC_TRACE(pdata, drv, "address 0x%x, data 0x%x", address, data); 2071 ret = smsc911x_eeprom_send_cmd(pdata, op); 2072 2073 if (!ret) { 2074 op = E2P_CMD_EPC_CMD_WRITE_ | address; 2075 smsc911x_reg_write(pdata, E2P_DATA, (u32)data); 2076 2077 /* Workaround for hardware read-after-write restriction */ 2078 smsc911x_reg_read(pdata, BYTE_TEST); 2079 2080 ret = smsc911x_eeprom_send_cmd(pdata, op); 2081 } 2082 2083 return ret; 2084 } 2085 2086 static int smsc911x_ethtool_get_eeprom_len(struct net_device *dev) 2087 { 2088 return SMSC911X_EEPROM_SIZE; 2089 } 2090 2091 static int smsc911x_ethtool_get_eeprom(struct net_device *dev, 2092 struct ethtool_eeprom *eeprom, u8 *data) 2093 { 2094 struct smsc911x_data *pdata = netdev_priv(dev); 2095 u8 eeprom_data[SMSC911X_EEPROM_SIZE]; 2096 int len; 2097 int i; 2098 2099 smsc911x_eeprom_enable_access(pdata); 2100 2101 len = min(eeprom->len, SMSC911X_EEPROM_SIZE); 2102 for (i = 0; i < len; i++) { 2103 int ret = smsc911x_eeprom_read_location(pdata, i, eeprom_data); 2104 if (ret < 0) { 2105 eeprom->len = 0; 2106 return ret; 2107 } 2108 } 2109 2110 memcpy(data, &eeprom_data[eeprom->offset], len); 2111 eeprom->len = len; 2112 return 0; 2113 } 2114 2115 static int smsc911x_ethtool_set_eeprom(struct net_device *dev, 2116 struct ethtool_eeprom *eeprom, u8 *data) 2117 { 2118 int ret; 2119 struct smsc911x_data *pdata = netdev_priv(dev); 2120 2121 smsc911x_eeprom_enable_access(pdata); 2122 smsc911x_eeprom_send_cmd(pdata, E2P_CMD_EPC_CMD_EWEN_); 2123 ret = smsc911x_eeprom_write_location(pdata, eeprom->offset, *data); 2124 smsc911x_eeprom_send_cmd(pdata, E2P_CMD_EPC_CMD_EWDS_); 2125 2126 /* Single byte write, according to man page */ 2127 eeprom->len = 1; 2128 2129 return ret; 2130 } 2131 2132 static const struct ethtool_ops smsc911x_ethtool_ops = { 2133 .get_link = ethtool_op_get_link, 2134 .get_drvinfo = smsc911x_ethtool_getdrvinfo, 2135 .nway_reset = phy_ethtool_nway_reset, 2136 .get_msglevel = smsc911x_ethtool_getmsglevel, 2137 .set_msglevel = smsc911x_ethtool_setmsglevel, 2138 .get_regs_len = smsc911x_ethtool_getregslen, 2139 .get_regs = smsc911x_ethtool_getregs, 2140 .get_eeprom_len = smsc911x_ethtool_get_eeprom_len, 2141 .get_eeprom = smsc911x_ethtool_get_eeprom, 2142 .set_eeprom = smsc911x_ethtool_set_eeprom, 2143 .get_ts_info = ethtool_op_get_ts_info, 2144 .get_link_ksettings = phy_ethtool_get_link_ksettings, 2145 .set_link_ksettings = phy_ethtool_set_link_ksettings, 2146 }; 2147 2148 static const struct net_device_ops smsc911x_netdev_ops = { 2149 .ndo_open = smsc911x_open, 2150 .ndo_stop = smsc911x_stop, 2151 .ndo_start_xmit = smsc911x_hard_start_xmit, 2152 .ndo_get_stats = smsc911x_get_stats, 2153 .ndo_set_rx_mode = smsc911x_set_multicast_list, 2154 .ndo_eth_ioctl = phy_do_ioctl_running, 2155 .ndo_validate_addr = eth_validate_addr, 2156 .ndo_set_mac_address = smsc911x_set_mac_address, 2157 #ifdef CONFIG_NET_POLL_CONTROLLER 2158 .ndo_poll_controller = smsc911x_poll_controller, 2159 #endif 2160 }; 2161 2162 /* copies the current mac address from hardware to dev->dev_addr */ 2163 static void smsc911x_read_mac_address(struct net_device *dev) 2164 { 2165 struct smsc911x_data *pdata = netdev_priv(dev); 2166 u32 mac_high16 = smsc911x_mac_read(pdata, ADDRH); 2167 u32 mac_low32 = smsc911x_mac_read(pdata, ADDRL); 2168 u8 addr[ETH_ALEN]; 2169 2170 addr[0] = (u8)(mac_low32); 2171 addr[1] = (u8)(mac_low32 >> 8); 2172 addr[2] = (u8)(mac_low32 >> 16); 2173 addr[3] = (u8)(mac_low32 >> 24); 2174 addr[4] = (u8)(mac_high16); 2175 addr[5] = (u8)(mac_high16 >> 8); 2176 eth_hw_addr_set(dev, addr); 2177 } 2178 2179 /* Initializing private device structures, only called from probe */ 2180 static int smsc911x_init(struct net_device *dev) 2181 { 2182 struct smsc911x_data *pdata = netdev_priv(dev); 2183 unsigned int byte_test, mask; 2184 unsigned int to = 100; 2185 2186 SMSC_TRACE(pdata, probe, "Driver Parameters:"); 2187 SMSC_TRACE(pdata, probe, "LAN base: 0x%08lX", 2188 (unsigned long)pdata->ioaddr); 2189 SMSC_TRACE(pdata, probe, "IRQ: %d", dev->irq); 2190 SMSC_TRACE(pdata, probe, "PHY will be autodetected."); 2191 2192 spin_lock_init(&pdata->dev_lock); 2193 spin_lock_init(&pdata->mac_lock); 2194 2195 if (pdata->ioaddr == NULL) { 2196 SMSC_WARN(pdata, probe, "pdata->ioaddr: 0x00000000"); 2197 return -ENODEV; 2198 } 2199 2200 /* 2201 * poll the READY bit in PMT_CTRL. Any other access to the device is 2202 * forbidden while this bit isn't set. Try for 100ms 2203 * 2204 * Note that this test is done before the WORD_SWAP register is 2205 * programmed. So in some configurations the READY bit is at 16 before 2206 * WORD_SWAP is written to. This issue is worked around by waiting 2207 * until either bit 0 or bit 16 gets set in PMT_CTRL. 2208 * 2209 * SMSC has confirmed that checking bit 16 (marked as reserved in 2210 * the datasheet) is fine since these bits "will either never be set 2211 * or can only go high after READY does (so also indicate the device 2212 * is ready)". 2213 */ 2214 2215 mask = PMT_CTRL_READY_ | swahw32(PMT_CTRL_READY_); 2216 while (!(smsc911x_reg_read(pdata, PMT_CTRL) & mask) && --to) 2217 udelay(1000); 2218 2219 if (to == 0) { 2220 netdev_err(dev, "Device not READY in 100ms aborting\n"); 2221 return -ENODEV; 2222 } 2223 2224 /* Check byte ordering */ 2225 byte_test = smsc911x_reg_read(pdata, BYTE_TEST); 2226 SMSC_TRACE(pdata, probe, "BYTE_TEST: 0x%08X", byte_test); 2227 if (byte_test == 0x43218765) { 2228 SMSC_TRACE(pdata, probe, "BYTE_TEST looks swapped, " 2229 "applying WORD_SWAP"); 2230 smsc911x_reg_write(pdata, WORD_SWAP, 0xffffffff); 2231 2232 /* 1 dummy read of BYTE_TEST is needed after a write to 2233 * WORD_SWAP before its contents are valid */ 2234 byte_test = smsc911x_reg_read(pdata, BYTE_TEST); 2235 2236 byte_test = smsc911x_reg_read(pdata, BYTE_TEST); 2237 } 2238 2239 if (byte_test != 0x87654321) { 2240 SMSC_WARN(pdata, drv, "BYTE_TEST: 0x%08X", byte_test); 2241 if (((byte_test >> 16) & 0xFFFF) == (byte_test & 0xFFFF)) { 2242 SMSC_WARN(pdata, probe, 2243 "top 16 bits equal to bottom 16 bits"); 2244 SMSC_TRACE(pdata, probe, 2245 "This may mean the chip is set " 2246 "for 32 bit while the bus is reading 16 bit"); 2247 } 2248 return -ENODEV; 2249 } 2250 2251 /* Default generation to zero (all workarounds apply) */ 2252 pdata->generation = 0; 2253 2254 pdata->idrev = smsc911x_reg_read(pdata, ID_REV); 2255 switch (pdata->idrev & 0xFFFF0000) { 2256 case LAN9118: 2257 case LAN9117: 2258 case LAN9116: 2259 case LAN9115: 2260 case LAN89218: 2261 /* LAN911[5678] family */ 2262 pdata->generation = pdata->idrev & 0x0000FFFF; 2263 break; 2264 2265 case LAN9218: 2266 case LAN9217: 2267 case LAN9216: 2268 case LAN9215: 2269 /* LAN921[5678] family */ 2270 pdata->generation = 3; 2271 break; 2272 2273 case LAN9210: 2274 case LAN9211: 2275 case LAN9220: 2276 case LAN9221: 2277 case LAN9250: 2278 /* LAN9210/LAN9211/LAN9220/LAN9221/LAN9250 */ 2279 pdata->generation = 4; 2280 break; 2281 2282 default: 2283 SMSC_WARN(pdata, probe, "LAN911x not identified, idrev: 0x%08X", 2284 pdata->idrev); 2285 return -ENODEV; 2286 } 2287 2288 SMSC_TRACE(pdata, probe, 2289 "LAN911x identified, idrev: 0x%08X, generation: %d", 2290 pdata->idrev, pdata->generation); 2291 2292 if (pdata->generation == 0) 2293 SMSC_WARN(pdata, probe, 2294 "This driver is not intended for this chip revision"); 2295 2296 /* workaround for platforms without an eeprom, where the mac address 2297 * is stored elsewhere and set by the bootloader. This saves the 2298 * mac address before resetting the device */ 2299 if (pdata->config.flags & SMSC911X_SAVE_MAC_ADDRESS) { 2300 spin_lock_irq(&pdata->mac_lock); 2301 smsc911x_read_mac_address(dev); 2302 spin_unlock_irq(&pdata->mac_lock); 2303 } 2304 2305 /* Reset the LAN911x */ 2306 if (smsc911x_phy_reset(pdata) || smsc911x_soft_reset(pdata)) 2307 return -ENODEV; 2308 2309 dev->flags |= IFF_MULTICAST; 2310 netif_napi_add_weight(dev, &pdata->napi, smsc911x_poll, 2311 SMSC_NAPI_WEIGHT); 2312 dev->netdev_ops = &smsc911x_netdev_ops; 2313 dev->ethtool_ops = &smsc911x_ethtool_ops; 2314 2315 return 0; 2316 } 2317 2318 static void smsc911x_drv_remove(struct platform_device *pdev) 2319 { 2320 struct net_device *dev; 2321 struct smsc911x_data *pdata; 2322 struct resource *res; 2323 2324 dev = platform_get_drvdata(pdev); 2325 BUG_ON(!dev); 2326 pdata = netdev_priv(dev); 2327 BUG_ON(!pdata); 2328 BUG_ON(!pdata->ioaddr); 2329 2330 SMSC_TRACE(pdata, ifdown, "Stopping driver"); 2331 2332 unregister_netdev(dev); 2333 2334 mdiobus_unregister(pdata->mii_bus); 2335 mdiobus_free(pdata->mii_bus); 2336 2337 res = platform_get_resource_byname(pdev, IORESOURCE_MEM, 2338 "smsc911x-memory"); 2339 if (!res) 2340 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 2341 2342 release_mem_region(res->start, resource_size(res)); 2343 2344 iounmap(pdata->ioaddr); 2345 2346 (void)smsc911x_disable_resources(pdev); 2347 smsc911x_free_resources(pdev); 2348 2349 free_netdev(dev); 2350 2351 pm_runtime_disable(&pdev->dev); 2352 } 2353 2354 /* standard register acces */ 2355 static const struct smsc911x_ops standard_smsc911x_ops = { 2356 .reg_read = __smsc911x_reg_read, 2357 .reg_write = __smsc911x_reg_write, 2358 .rx_readfifo = smsc911x_rx_readfifo, 2359 .tx_writefifo = smsc911x_tx_writefifo, 2360 }; 2361 2362 /* shifted register access */ 2363 static const struct smsc911x_ops shifted_smsc911x_ops = { 2364 .reg_read = __smsc911x_reg_read_shift, 2365 .reg_write = __smsc911x_reg_write_shift, 2366 .rx_readfifo = smsc911x_rx_readfifo_shift, 2367 .tx_writefifo = smsc911x_tx_writefifo_shift, 2368 }; 2369 2370 static int smsc911x_probe_config(struct smsc911x_platform_config *config, 2371 struct device *dev) 2372 { 2373 int phy_interface; 2374 u32 width = 0; 2375 int err; 2376 2377 phy_interface = device_get_phy_mode(dev); 2378 if (phy_interface < 0) 2379 phy_interface = PHY_INTERFACE_MODE_NA; 2380 config->phy_interface = phy_interface; 2381 2382 device_get_mac_address(dev, config->mac); 2383 2384 err = device_property_read_u32(dev, "reg-io-width", &width); 2385 if (err == -ENXIO) 2386 return err; 2387 if (!err && width == 4) 2388 config->flags |= SMSC911X_USE_32BIT; 2389 else 2390 config->flags |= SMSC911X_USE_16BIT; 2391 2392 device_property_read_u32(dev, "reg-shift", &config->shift); 2393 2394 if (device_property_present(dev, "smsc,irq-active-high")) 2395 config->irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_HIGH; 2396 2397 if (device_property_present(dev, "smsc,irq-push-pull")) 2398 config->irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL; 2399 2400 if (device_property_present(dev, "smsc,force-internal-phy")) 2401 config->flags |= SMSC911X_FORCE_INTERNAL_PHY; 2402 2403 if (device_property_present(dev, "smsc,force-external-phy")) 2404 config->flags |= SMSC911X_FORCE_EXTERNAL_PHY; 2405 2406 if (device_property_present(dev, "smsc,save-mac-address")) 2407 config->flags |= SMSC911X_SAVE_MAC_ADDRESS; 2408 2409 return 0; 2410 } 2411 2412 static int smsc911x_drv_probe(struct platform_device *pdev) 2413 { 2414 struct net_device *dev; 2415 struct smsc911x_data *pdata; 2416 struct smsc911x_platform_config *config = dev_get_platdata(&pdev->dev); 2417 struct resource *res; 2418 int res_size, irq; 2419 int retval; 2420 2421 res = platform_get_resource_byname(pdev, IORESOURCE_MEM, 2422 "smsc911x-memory"); 2423 if (!res) 2424 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 2425 if (!res) { 2426 pr_warn("Could not allocate resource\n"); 2427 retval = -ENODEV; 2428 goto out_0; 2429 } 2430 res_size = resource_size(res); 2431 2432 irq = platform_get_irq(pdev, 0); 2433 if (irq == -EPROBE_DEFER) { 2434 retval = -EPROBE_DEFER; 2435 goto out_0; 2436 } else if (irq < 0) { 2437 pr_warn("Could not allocate irq resource\n"); 2438 retval = -ENODEV; 2439 goto out_0; 2440 } 2441 2442 if (!request_mem_region(res->start, res_size, SMSC_CHIPNAME)) { 2443 retval = -EBUSY; 2444 goto out_0; 2445 } 2446 2447 dev = alloc_etherdev(sizeof(struct smsc911x_data)); 2448 if (!dev) { 2449 retval = -ENOMEM; 2450 goto out_release_io_1; 2451 } 2452 2453 SET_NETDEV_DEV(dev, &pdev->dev); 2454 2455 pdata = netdev_priv(dev); 2456 dev->irq = irq; 2457 pdata->ioaddr = ioremap(res->start, res_size); 2458 if (!pdata->ioaddr) { 2459 retval = -ENOMEM; 2460 goto out_ioremap_fail; 2461 } 2462 2463 pdata->dev = dev; 2464 pdata->msg_enable = ((1 << debug) - 1); 2465 2466 platform_set_drvdata(pdev, dev); 2467 2468 retval = smsc911x_request_resources(pdev); 2469 if (retval) 2470 goto out_request_resources_fail; 2471 2472 retval = smsc911x_enable_resources(pdev); 2473 if (retval) 2474 goto out_enable_resources_fail; 2475 2476 if (pdata->ioaddr == NULL) { 2477 SMSC_WARN(pdata, probe, "Error smsc911x base address invalid"); 2478 retval = -ENOMEM; 2479 goto out_disable_resources; 2480 } 2481 2482 retval = smsc911x_probe_config(&pdata->config, &pdev->dev); 2483 if (retval && config) { 2484 /* copy config parameters across to pdata */ 2485 memcpy(&pdata->config, config, sizeof(pdata->config)); 2486 retval = 0; 2487 } 2488 2489 if (retval) { 2490 SMSC_WARN(pdata, probe, "Error smsc911x config not found"); 2491 goto out_disable_resources; 2492 } 2493 2494 /* assume standard, non-shifted, access to HW registers */ 2495 pdata->ops = &standard_smsc911x_ops; 2496 /* apply the right access if shifting is needed */ 2497 if (pdata->config.shift) 2498 pdata->ops = &shifted_smsc911x_ops; 2499 2500 pm_runtime_enable(&pdev->dev); 2501 pm_runtime_get_sync(&pdev->dev); 2502 2503 retval = smsc911x_init(dev); 2504 if (retval < 0) 2505 goto out_init_fail; 2506 2507 netif_carrier_off(dev); 2508 2509 retval = smsc911x_mii_init(pdev, dev); 2510 if (retval) { 2511 SMSC_WARN(pdata, probe, "Error %i initialising mii", retval); 2512 goto out_init_fail; 2513 } 2514 2515 retval = register_netdev(dev); 2516 if (retval) { 2517 SMSC_WARN(pdata, probe, "Error %i registering device", retval); 2518 goto out_init_fail; 2519 } else { 2520 SMSC_TRACE(pdata, probe, 2521 "Network interface: \"%s\"", dev->name); 2522 } 2523 2524 spin_lock_irq(&pdata->mac_lock); 2525 2526 /* Check if mac address has been specified when bringing interface up */ 2527 if (is_valid_ether_addr(dev->dev_addr)) { 2528 smsc911x_set_hw_mac_address(pdata, dev->dev_addr); 2529 SMSC_TRACE(pdata, probe, 2530 "MAC Address is specified by configuration"); 2531 } else if (is_valid_ether_addr(pdata->config.mac)) { 2532 eth_hw_addr_set(dev, pdata->config.mac); 2533 SMSC_TRACE(pdata, probe, 2534 "MAC Address specified by platform data"); 2535 } else { 2536 /* Try reading mac address from device. if EEPROM is present 2537 * it will already have been set */ 2538 smsc_get_mac(dev); 2539 2540 if (is_valid_ether_addr(dev->dev_addr)) { 2541 /* eeprom values are valid so use them */ 2542 SMSC_TRACE(pdata, probe, 2543 "Mac Address is read from LAN911x EEPROM"); 2544 } else { 2545 /* eeprom values are invalid, generate random MAC */ 2546 eth_hw_addr_random(dev); 2547 smsc911x_set_hw_mac_address(pdata, dev->dev_addr); 2548 SMSC_TRACE(pdata, probe, 2549 "MAC Address is set to eth_random_addr"); 2550 } 2551 } 2552 2553 spin_unlock_irq(&pdata->mac_lock); 2554 pm_runtime_put(&pdev->dev); 2555 2556 netdev_info(dev, "MAC Address: %pM\n", dev->dev_addr); 2557 2558 return 0; 2559 2560 out_init_fail: 2561 pm_runtime_put(&pdev->dev); 2562 pm_runtime_disable(&pdev->dev); 2563 out_disable_resources: 2564 (void)smsc911x_disable_resources(pdev); 2565 out_enable_resources_fail: 2566 smsc911x_free_resources(pdev); 2567 out_request_resources_fail: 2568 iounmap(pdata->ioaddr); 2569 out_ioremap_fail: 2570 free_netdev(dev); 2571 out_release_io_1: 2572 release_mem_region(res->start, resource_size(res)); 2573 out_0: 2574 return retval; 2575 } 2576 2577 #ifdef CONFIG_PM 2578 /* This implementation assumes the devices remains powered on its VDDVARIO 2579 * pins during suspend. */ 2580 2581 /* TODO: implement freeze/thaw callbacks for hibernation.*/ 2582 2583 static int smsc911x_suspend(struct device *dev) 2584 { 2585 struct net_device *ndev = dev_get_drvdata(dev); 2586 struct smsc911x_data *pdata = netdev_priv(ndev); 2587 2588 if (netif_running(ndev)) { 2589 netif_stop_queue(ndev); 2590 netif_device_detach(ndev); 2591 if (!device_may_wakeup(dev)) 2592 phy_stop(ndev->phydev); 2593 } 2594 2595 /* enable wake on LAN, energy detection and the external PME 2596 * signal. */ 2597 smsc911x_reg_write(pdata, PMT_CTRL, 2598 PMT_CTRL_PM_MODE_D1_ | PMT_CTRL_WOL_EN_ | 2599 PMT_CTRL_ED_EN_ | PMT_CTRL_PME_EN_); 2600 2601 pm_runtime_disable(dev); 2602 pm_runtime_set_suspended(dev); 2603 2604 return 0; 2605 } 2606 2607 static int smsc911x_resume(struct device *dev) 2608 { 2609 struct net_device *ndev = dev_get_drvdata(dev); 2610 struct smsc911x_data *pdata = netdev_priv(ndev); 2611 unsigned int to = 100; 2612 2613 pm_runtime_enable(dev); 2614 pm_runtime_resume(dev); 2615 2616 /* Note 3.11 from the datasheet: 2617 * "When the LAN9220 is in a power saving state, a write of any 2618 * data to the BYTE_TEST register will wake-up the device." 2619 */ 2620 smsc911x_reg_write(pdata, BYTE_TEST, 0); 2621 2622 /* poll the READY bit in PMT_CTRL. Any other access to the device is 2623 * forbidden while this bit isn't set. Try for 100ms and return -EIO 2624 * if it failed. */ 2625 while (!(smsc911x_reg_read(pdata, PMT_CTRL) & PMT_CTRL_READY_) && --to) 2626 udelay(1000); 2627 2628 if (to == 0) 2629 return -EIO; 2630 2631 if (netif_running(ndev)) { 2632 netif_device_attach(ndev); 2633 netif_start_queue(ndev); 2634 if (!device_may_wakeup(dev)) 2635 phy_start(ndev->phydev); 2636 } 2637 2638 return 0; 2639 } 2640 2641 static const struct dev_pm_ops smsc911x_pm_ops = { 2642 .suspend = smsc911x_suspend, 2643 .resume = smsc911x_resume, 2644 }; 2645 2646 #define SMSC911X_PM_OPS (&smsc911x_pm_ops) 2647 2648 #else 2649 #define SMSC911X_PM_OPS NULL 2650 #endif 2651 2652 #ifdef CONFIG_OF 2653 static const struct of_device_id smsc911x_dt_ids[] = { 2654 { .compatible = "smsc,lan9115", }, 2655 { /* sentinel */ } 2656 }; 2657 MODULE_DEVICE_TABLE(of, smsc911x_dt_ids); 2658 #endif 2659 2660 #ifdef CONFIG_ACPI 2661 static const struct acpi_device_id smsc911x_acpi_match[] = { 2662 { "ARMH9118", 0 }, 2663 { } 2664 }; 2665 MODULE_DEVICE_TABLE(acpi, smsc911x_acpi_match); 2666 #endif 2667 2668 static struct platform_driver smsc911x_driver = { 2669 .probe = smsc911x_drv_probe, 2670 .remove_new = smsc911x_drv_remove, 2671 .driver = { 2672 .name = SMSC_CHIPNAME, 2673 .pm = SMSC911X_PM_OPS, 2674 .of_match_table = of_match_ptr(smsc911x_dt_ids), 2675 .acpi_match_table = ACPI_PTR(smsc911x_acpi_match), 2676 }, 2677 }; 2678 2679 /* Entry point for loading the module */ 2680 static int __init smsc911x_init_module(void) 2681 { 2682 SMSC_INITIALIZE(); 2683 return platform_driver_register(&smsc911x_driver); 2684 } 2685 2686 /* entry point for unloading the module */ 2687 static void __exit smsc911x_cleanup_module(void) 2688 { 2689 platform_driver_unregister(&smsc911x_driver); 2690 } 2691 2692 module_init(smsc911x_init_module); 2693 module_exit(smsc911x_cleanup_module); 2694