1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /*************************************************************************** 3 * 4 * Copyright (C) 2004-2008 SMSC 5 * Copyright (C) 2005-2008 ARM 6 * 7 *************************************************************************** 8 * Rewritten, heavily based on smsc911x simple driver by SMSC. 9 * Partly uses io macros from smc91x.c by Nicolas Pitre 10 * 11 * Supported devices: 12 * LAN9115, LAN9116, LAN9117, LAN9118 13 * LAN9215, LAN9216, LAN9217, LAN9218 14 * LAN9210, LAN9211 15 * LAN9220, LAN9221 16 * LAN89218,LAN9250 17 */ 18 19 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt 20 21 #include <linux/crc32.h> 22 #include <linux/clk.h> 23 #include <linux/delay.h> 24 #include <linux/errno.h> 25 #include <linux/etherdevice.h> 26 #include <linux/ethtool.h> 27 #include <linux/init.h> 28 #include <linux/interrupt.h> 29 #include <linux/ioport.h> 30 #include <linux/kernel.h> 31 #include <linux/module.h> 32 #include <linux/netdevice.h> 33 #include <linux/platform_device.h> 34 #include <linux/regulator/consumer.h> 35 #include <linux/sched.h> 36 #include <linux/timer.h> 37 #include <linux/bug.h> 38 #include <linux/bitops.h> 39 #include <linux/irq.h> 40 #include <linux/io.h> 41 #include <linux/swab.h> 42 #include <linux/phy.h> 43 #include <linux/smsc911x.h> 44 #include <linux/device.h> 45 #include <linux/of.h> 46 #include <linux/of_device.h> 47 #include <linux/of_gpio.h> 48 #include <linux/of_net.h> 49 #include <linux/acpi.h> 50 #include <linux/pm_runtime.h> 51 #include <linux/property.h> 52 #include <linux/gpio/consumer.h> 53 54 #include "smsc911x.h" 55 56 #define SMSC_CHIPNAME "smsc911x" 57 #define SMSC_MDIONAME "smsc911x-mdio" 58 #define SMSC_DRV_VERSION "2008-10-21" 59 60 MODULE_LICENSE("GPL"); 61 MODULE_VERSION(SMSC_DRV_VERSION); 62 MODULE_ALIAS("platform:smsc911x"); 63 64 #if USE_DEBUG > 0 65 static int debug = 16; 66 #else 67 static int debug = 3; 68 #endif 69 70 module_param(debug, int, 0); 71 MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)"); 72 73 struct smsc911x_data; 74 75 struct smsc911x_ops { 76 u32 (*reg_read)(struct smsc911x_data *pdata, u32 reg); 77 void (*reg_write)(struct smsc911x_data *pdata, u32 reg, u32 val); 78 void (*rx_readfifo)(struct smsc911x_data *pdata, 79 unsigned int *buf, unsigned int wordcount); 80 void (*tx_writefifo)(struct smsc911x_data *pdata, 81 unsigned int *buf, unsigned int wordcount); 82 }; 83 84 #define SMSC911X_NUM_SUPPLIES 2 85 86 struct smsc911x_data { 87 void __iomem *ioaddr; 88 89 unsigned int idrev; 90 91 /* used to decide which workarounds apply */ 92 unsigned int generation; 93 94 /* device configuration (copied from platform_data during probe) */ 95 struct smsc911x_platform_config config; 96 97 /* This needs to be acquired before calling any of below: 98 * smsc911x_mac_read(), smsc911x_mac_write() 99 */ 100 spinlock_t mac_lock; 101 102 /* spinlock to ensure register accesses are serialised */ 103 spinlock_t dev_lock; 104 105 struct mii_bus *mii_bus; 106 unsigned int using_extphy; 107 int last_duplex; 108 int last_carrier; 109 110 u32 msg_enable; 111 unsigned int gpio_setting; 112 unsigned int gpio_orig_setting; 113 struct net_device *dev; 114 struct napi_struct napi; 115 116 unsigned int software_irq_signal; 117 118 #ifdef USE_PHY_WORK_AROUND 119 #define MIN_PACKET_SIZE (64) 120 char loopback_tx_pkt[MIN_PACKET_SIZE]; 121 char loopback_rx_pkt[MIN_PACKET_SIZE]; 122 unsigned int resetcount; 123 #endif 124 125 /* Members for Multicast filter workaround */ 126 unsigned int multicast_update_pending; 127 unsigned int set_bits_mask; 128 unsigned int clear_bits_mask; 129 unsigned int hashhi; 130 unsigned int hashlo; 131 132 /* register access functions */ 133 const struct smsc911x_ops *ops; 134 135 /* regulators */ 136 struct regulator_bulk_data supplies[SMSC911X_NUM_SUPPLIES]; 137 138 /* Reset GPIO */ 139 struct gpio_desc *reset_gpiod; 140 141 /* clock */ 142 struct clk *clk; 143 }; 144 145 /* Easy access to information */ 146 #define __smsc_shift(pdata, reg) ((reg) << ((pdata)->config.shift)) 147 148 static inline u32 __smsc911x_reg_read(struct smsc911x_data *pdata, u32 reg) 149 { 150 if (pdata->config.flags & SMSC911X_USE_32BIT) 151 return readl(pdata->ioaddr + reg); 152 153 if (pdata->config.flags & SMSC911X_USE_16BIT) 154 return ((readw(pdata->ioaddr + reg) & 0xFFFF) | 155 ((readw(pdata->ioaddr + reg + 2) & 0xFFFF) << 16)); 156 157 BUG(); 158 return 0; 159 } 160 161 static inline u32 162 __smsc911x_reg_read_shift(struct smsc911x_data *pdata, u32 reg) 163 { 164 if (pdata->config.flags & SMSC911X_USE_32BIT) 165 return readl(pdata->ioaddr + __smsc_shift(pdata, reg)); 166 167 if (pdata->config.flags & SMSC911X_USE_16BIT) 168 return (readw(pdata->ioaddr + 169 __smsc_shift(pdata, reg)) & 0xFFFF) | 170 ((readw(pdata->ioaddr + 171 __smsc_shift(pdata, reg + 2)) & 0xFFFF) << 16); 172 173 BUG(); 174 return 0; 175 } 176 177 static inline u32 smsc911x_reg_read(struct smsc911x_data *pdata, u32 reg) 178 { 179 u32 data; 180 unsigned long flags; 181 182 spin_lock_irqsave(&pdata->dev_lock, flags); 183 data = pdata->ops->reg_read(pdata, reg); 184 spin_unlock_irqrestore(&pdata->dev_lock, flags); 185 186 return data; 187 } 188 189 static inline void __smsc911x_reg_write(struct smsc911x_data *pdata, u32 reg, 190 u32 val) 191 { 192 if (pdata->config.flags & SMSC911X_USE_32BIT) { 193 writel(val, pdata->ioaddr + reg); 194 return; 195 } 196 197 if (pdata->config.flags & SMSC911X_USE_16BIT) { 198 writew(val & 0xFFFF, pdata->ioaddr + reg); 199 writew((val >> 16) & 0xFFFF, pdata->ioaddr + reg + 2); 200 return; 201 } 202 203 BUG(); 204 } 205 206 static inline void 207 __smsc911x_reg_write_shift(struct smsc911x_data *pdata, u32 reg, u32 val) 208 { 209 if (pdata->config.flags & SMSC911X_USE_32BIT) { 210 writel(val, pdata->ioaddr + __smsc_shift(pdata, reg)); 211 return; 212 } 213 214 if (pdata->config.flags & SMSC911X_USE_16BIT) { 215 writew(val & 0xFFFF, 216 pdata->ioaddr + __smsc_shift(pdata, reg)); 217 writew((val >> 16) & 0xFFFF, 218 pdata->ioaddr + __smsc_shift(pdata, reg + 2)); 219 return; 220 } 221 222 BUG(); 223 } 224 225 static inline void smsc911x_reg_write(struct smsc911x_data *pdata, u32 reg, 226 u32 val) 227 { 228 unsigned long flags; 229 230 spin_lock_irqsave(&pdata->dev_lock, flags); 231 pdata->ops->reg_write(pdata, reg, val); 232 spin_unlock_irqrestore(&pdata->dev_lock, flags); 233 } 234 235 /* Writes a packet to the TX_DATA_FIFO */ 236 static inline void 237 smsc911x_tx_writefifo(struct smsc911x_data *pdata, unsigned int *buf, 238 unsigned int wordcount) 239 { 240 unsigned long flags; 241 242 spin_lock_irqsave(&pdata->dev_lock, flags); 243 244 if (pdata->config.flags & SMSC911X_SWAP_FIFO) { 245 while (wordcount--) 246 __smsc911x_reg_write(pdata, TX_DATA_FIFO, 247 swab32(*buf++)); 248 goto out; 249 } 250 251 if (pdata->config.flags & SMSC911X_USE_32BIT) { 252 iowrite32_rep(pdata->ioaddr + TX_DATA_FIFO, buf, wordcount); 253 goto out; 254 } 255 256 if (pdata->config.flags & SMSC911X_USE_16BIT) { 257 while (wordcount--) 258 __smsc911x_reg_write(pdata, TX_DATA_FIFO, *buf++); 259 goto out; 260 } 261 262 BUG(); 263 out: 264 spin_unlock_irqrestore(&pdata->dev_lock, flags); 265 } 266 267 /* Writes a packet to the TX_DATA_FIFO - shifted version */ 268 static inline void 269 smsc911x_tx_writefifo_shift(struct smsc911x_data *pdata, unsigned int *buf, 270 unsigned int wordcount) 271 { 272 unsigned long flags; 273 274 spin_lock_irqsave(&pdata->dev_lock, flags); 275 276 if (pdata->config.flags & SMSC911X_SWAP_FIFO) { 277 while (wordcount--) 278 __smsc911x_reg_write_shift(pdata, TX_DATA_FIFO, 279 swab32(*buf++)); 280 goto out; 281 } 282 283 if (pdata->config.flags & SMSC911X_USE_32BIT) { 284 iowrite32_rep(pdata->ioaddr + __smsc_shift(pdata, 285 TX_DATA_FIFO), buf, wordcount); 286 goto out; 287 } 288 289 if (pdata->config.flags & SMSC911X_USE_16BIT) { 290 while (wordcount--) 291 __smsc911x_reg_write_shift(pdata, 292 TX_DATA_FIFO, *buf++); 293 goto out; 294 } 295 296 BUG(); 297 out: 298 spin_unlock_irqrestore(&pdata->dev_lock, flags); 299 } 300 301 /* Reads a packet out of the RX_DATA_FIFO */ 302 static inline void 303 smsc911x_rx_readfifo(struct smsc911x_data *pdata, unsigned int *buf, 304 unsigned int wordcount) 305 { 306 unsigned long flags; 307 308 spin_lock_irqsave(&pdata->dev_lock, flags); 309 310 if (pdata->config.flags & SMSC911X_SWAP_FIFO) { 311 while (wordcount--) 312 *buf++ = swab32(__smsc911x_reg_read(pdata, 313 RX_DATA_FIFO)); 314 goto out; 315 } 316 317 if (pdata->config.flags & SMSC911X_USE_32BIT) { 318 ioread32_rep(pdata->ioaddr + RX_DATA_FIFO, buf, wordcount); 319 goto out; 320 } 321 322 if (pdata->config.flags & SMSC911X_USE_16BIT) { 323 while (wordcount--) 324 *buf++ = __smsc911x_reg_read(pdata, RX_DATA_FIFO); 325 goto out; 326 } 327 328 BUG(); 329 out: 330 spin_unlock_irqrestore(&pdata->dev_lock, flags); 331 } 332 333 /* Reads a packet out of the RX_DATA_FIFO - shifted version */ 334 static inline void 335 smsc911x_rx_readfifo_shift(struct smsc911x_data *pdata, unsigned int *buf, 336 unsigned int wordcount) 337 { 338 unsigned long flags; 339 340 spin_lock_irqsave(&pdata->dev_lock, flags); 341 342 if (pdata->config.flags & SMSC911X_SWAP_FIFO) { 343 while (wordcount--) 344 *buf++ = swab32(__smsc911x_reg_read_shift(pdata, 345 RX_DATA_FIFO)); 346 goto out; 347 } 348 349 if (pdata->config.flags & SMSC911X_USE_32BIT) { 350 ioread32_rep(pdata->ioaddr + __smsc_shift(pdata, 351 RX_DATA_FIFO), buf, wordcount); 352 goto out; 353 } 354 355 if (pdata->config.flags & SMSC911X_USE_16BIT) { 356 while (wordcount--) 357 *buf++ = __smsc911x_reg_read_shift(pdata, 358 RX_DATA_FIFO); 359 goto out; 360 } 361 362 BUG(); 363 out: 364 spin_unlock_irqrestore(&pdata->dev_lock, flags); 365 } 366 367 /* 368 * enable regulator and clock resources. 369 */ 370 static int smsc911x_enable_resources(struct platform_device *pdev) 371 { 372 struct net_device *ndev = platform_get_drvdata(pdev); 373 struct smsc911x_data *pdata = netdev_priv(ndev); 374 int ret = 0; 375 376 ret = regulator_bulk_enable(ARRAY_SIZE(pdata->supplies), 377 pdata->supplies); 378 if (ret) 379 netdev_err(ndev, "failed to enable regulators %d\n", 380 ret); 381 382 if (!IS_ERR(pdata->clk)) { 383 ret = clk_prepare_enable(pdata->clk); 384 if (ret < 0) 385 netdev_err(ndev, "failed to enable clock %d\n", ret); 386 } 387 388 return ret; 389 } 390 391 /* 392 * disable resources, currently just regulators. 393 */ 394 static int smsc911x_disable_resources(struct platform_device *pdev) 395 { 396 struct net_device *ndev = platform_get_drvdata(pdev); 397 struct smsc911x_data *pdata = netdev_priv(ndev); 398 int ret = 0; 399 400 ret = regulator_bulk_disable(ARRAY_SIZE(pdata->supplies), 401 pdata->supplies); 402 403 if (!IS_ERR(pdata->clk)) 404 clk_disable_unprepare(pdata->clk); 405 406 return ret; 407 } 408 409 /* 410 * Request resources, currently just regulators. 411 * 412 * The SMSC911x has two power pins: vddvario and vdd33a, in designs where 413 * these are not always-on we need to request regulators to be turned on 414 * before we can try to access the device registers. 415 */ 416 static int smsc911x_request_resources(struct platform_device *pdev) 417 { 418 struct net_device *ndev = platform_get_drvdata(pdev); 419 struct smsc911x_data *pdata = netdev_priv(ndev); 420 int ret = 0; 421 422 /* Request regulators */ 423 pdata->supplies[0].supply = "vdd33a"; 424 pdata->supplies[1].supply = "vddvario"; 425 ret = regulator_bulk_get(&pdev->dev, 426 ARRAY_SIZE(pdata->supplies), 427 pdata->supplies); 428 if (ret) { 429 /* 430 * Retry on deferrals, else just report the error 431 * and try to continue. 432 */ 433 if (ret == -EPROBE_DEFER) 434 return ret; 435 netdev_err(ndev, "couldn't get regulators %d\n", 436 ret); 437 } 438 439 /* Request optional RESET GPIO */ 440 pdata->reset_gpiod = devm_gpiod_get_optional(&pdev->dev, 441 "reset", 442 GPIOD_OUT_LOW); 443 444 /* Request clock */ 445 pdata->clk = clk_get(&pdev->dev, NULL); 446 if (IS_ERR(pdata->clk)) 447 dev_dbg(&pdev->dev, "couldn't get clock %li\n", 448 PTR_ERR(pdata->clk)); 449 450 return ret; 451 } 452 453 /* 454 * Free resources, currently just regulators. 455 * 456 */ 457 static void smsc911x_free_resources(struct platform_device *pdev) 458 { 459 struct net_device *ndev = platform_get_drvdata(pdev); 460 struct smsc911x_data *pdata = netdev_priv(ndev); 461 462 /* Free regulators */ 463 regulator_bulk_free(ARRAY_SIZE(pdata->supplies), 464 pdata->supplies); 465 466 /* Free clock */ 467 if (!IS_ERR(pdata->clk)) { 468 clk_put(pdata->clk); 469 pdata->clk = NULL; 470 } 471 } 472 473 /* waits for MAC not busy, with timeout. Only called by smsc911x_mac_read 474 * and smsc911x_mac_write, so assumes mac_lock is held */ 475 static int smsc911x_mac_complete(struct smsc911x_data *pdata) 476 { 477 int i; 478 u32 val; 479 480 SMSC_ASSERT_MAC_LOCK(pdata); 481 482 for (i = 0; i < 40; i++) { 483 val = smsc911x_reg_read(pdata, MAC_CSR_CMD); 484 if (!(val & MAC_CSR_CMD_CSR_BUSY_)) 485 return 0; 486 } 487 SMSC_WARN(pdata, hw, "Timed out waiting for MAC not BUSY. " 488 "MAC_CSR_CMD: 0x%08X", val); 489 return -EIO; 490 } 491 492 /* Fetches a MAC register value. Assumes mac_lock is acquired */ 493 static u32 smsc911x_mac_read(struct smsc911x_data *pdata, unsigned int offset) 494 { 495 unsigned int temp; 496 497 SMSC_ASSERT_MAC_LOCK(pdata); 498 499 temp = smsc911x_reg_read(pdata, MAC_CSR_CMD); 500 if (unlikely(temp & MAC_CSR_CMD_CSR_BUSY_)) { 501 SMSC_WARN(pdata, hw, "MAC busy at entry"); 502 return 0xFFFFFFFF; 503 } 504 505 /* Send the MAC cmd */ 506 smsc911x_reg_write(pdata, MAC_CSR_CMD, ((offset & 0xFF) | 507 MAC_CSR_CMD_CSR_BUSY_ | MAC_CSR_CMD_R_NOT_W_)); 508 509 /* Workaround for hardware read-after-write restriction */ 510 temp = smsc911x_reg_read(pdata, BYTE_TEST); 511 512 /* Wait for the read to complete */ 513 if (likely(smsc911x_mac_complete(pdata) == 0)) 514 return smsc911x_reg_read(pdata, MAC_CSR_DATA); 515 516 SMSC_WARN(pdata, hw, "MAC busy after read"); 517 return 0xFFFFFFFF; 518 } 519 520 /* Set a mac register, mac_lock must be acquired before calling */ 521 static void smsc911x_mac_write(struct smsc911x_data *pdata, 522 unsigned int offset, u32 val) 523 { 524 unsigned int temp; 525 526 SMSC_ASSERT_MAC_LOCK(pdata); 527 528 temp = smsc911x_reg_read(pdata, MAC_CSR_CMD); 529 if (unlikely(temp & MAC_CSR_CMD_CSR_BUSY_)) { 530 SMSC_WARN(pdata, hw, 531 "smsc911x_mac_write failed, MAC busy at entry"); 532 return; 533 } 534 535 /* Send data to write */ 536 smsc911x_reg_write(pdata, MAC_CSR_DATA, val); 537 538 /* Write the actual data */ 539 smsc911x_reg_write(pdata, MAC_CSR_CMD, ((offset & 0xFF) | 540 MAC_CSR_CMD_CSR_BUSY_)); 541 542 /* Workaround for hardware read-after-write restriction */ 543 temp = smsc911x_reg_read(pdata, BYTE_TEST); 544 545 /* Wait for the write to complete */ 546 if (likely(smsc911x_mac_complete(pdata) == 0)) 547 return; 548 549 SMSC_WARN(pdata, hw, "smsc911x_mac_write failed, MAC busy after write"); 550 } 551 552 /* Get a phy register */ 553 static int smsc911x_mii_read(struct mii_bus *bus, int phyaddr, int regidx) 554 { 555 struct smsc911x_data *pdata = (struct smsc911x_data *)bus->priv; 556 unsigned long flags; 557 unsigned int addr; 558 int i, reg; 559 560 pm_runtime_get_sync(bus->parent); 561 spin_lock_irqsave(&pdata->mac_lock, flags); 562 563 /* Confirm MII not busy */ 564 if (unlikely(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) { 565 SMSC_WARN(pdata, hw, "MII is busy in smsc911x_mii_read???"); 566 reg = -EIO; 567 goto out; 568 } 569 570 /* Set the address, index & direction (read from PHY) */ 571 addr = ((phyaddr & 0x1F) << 11) | ((regidx & 0x1F) << 6); 572 smsc911x_mac_write(pdata, MII_ACC, addr); 573 574 /* Wait for read to complete w/ timeout */ 575 for (i = 0; i < 100; i++) 576 if (!(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) { 577 reg = smsc911x_mac_read(pdata, MII_DATA); 578 goto out; 579 } 580 581 SMSC_WARN(pdata, hw, "Timed out waiting for MII read to finish"); 582 reg = -EIO; 583 584 out: 585 spin_unlock_irqrestore(&pdata->mac_lock, flags); 586 pm_runtime_put(bus->parent); 587 return reg; 588 } 589 590 /* Set a phy register */ 591 static int smsc911x_mii_write(struct mii_bus *bus, int phyaddr, int regidx, 592 u16 val) 593 { 594 struct smsc911x_data *pdata = (struct smsc911x_data *)bus->priv; 595 unsigned long flags; 596 unsigned int addr; 597 int i, reg; 598 599 pm_runtime_get_sync(bus->parent); 600 spin_lock_irqsave(&pdata->mac_lock, flags); 601 602 /* Confirm MII not busy */ 603 if (unlikely(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) { 604 SMSC_WARN(pdata, hw, "MII is busy in smsc911x_mii_write???"); 605 reg = -EIO; 606 goto out; 607 } 608 609 /* Put the data to write in the MAC */ 610 smsc911x_mac_write(pdata, MII_DATA, val); 611 612 /* Set the address, index & direction (write to PHY) */ 613 addr = ((phyaddr & 0x1F) << 11) | ((regidx & 0x1F) << 6) | 614 MII_ACC_MII_WRITE_; 615 smsc911x_mac_write(pdata, MII_ACC, addr); 616 617 /* Wait for write to complete w/ timeout */ 618 for (i = 0; i < 100; i++) 619 if (!(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) { 620 reg = 0; 621 goto out; 622 } 623 624 SMSC_WARN(pdata, hw, "Timed out waiting for MII write to finish"); 625 reg = -EIO; 626 627 out: 628 spin_unlock_irqrestore(&pdata->mac_lock, flags); 629 pm_runtime_put(bus->parent); 630 return reg; 631 } 632 633 /* Switch to external phy. Assumes tx and rx are stopped. */ 634 static void smsc911x_phy_enable_external(struct smsc911x_data *pdata) 635 { 636 unsigned int hwcfg = smsc911x_reg_read(pdata, HW_CFG); 637 638 /* Disable phy clocks to the MAC */ 639 hwcfg &= (~HW_CFG_PHY_CLK_SEL_); 640 hwcfg |= HW_CFG_PHY_CLK_SEL_CLK_DIS_; 641 smsc911x_reg_write(pdata, HW_CFG, hwcfg); 642 udelay(10); /* Enough time for clocks to stop */ 643 644 /* Switch to external phy */ 645 hwcfg |= HW_CFG_EXT_PHY_EN_; 646 smsc911x_reg_write(pdata, HW_CFG, hwcfg); 647 648 /* Enable phy clocks to the MAC */ 649 hwcfg &= (~HW_CFG_PHY_CLK_SEL_); 650 hwcfg |= HW_CFG_PHY_CLK_SEL_EXT_PHY_; 651 smsc911x_reg_write(pdata, HW_CFG, hwcfg); 652 udelay(10); /* Enough time for clocks to restart */ 653 654 hwcfg |= HW_CFG_SMI_SEL_; 655 smsc911x_reg_write(pdata, HW_CFG, hwcfg); 656 } 657 658 /* Autodetects and enables external phy if present on supported chips. 659 * autodetection can be overridden by specifying SMSC911X_FORCE_INTERNAL_PHY 660 * or SMSC911X_FORCE_EXTERNAL_PHY in the platform_data flags. */ 661 static void smsc911x_phy_initialise_external(struct smsc911x_data *pdata) 662 { 663 unsigned int hwcfg = smsc911x_reg_read(pdata, HW_CFG); 664 665 if (pdata->config.flags & SMSC911X_FORCE_INTERNAL_PHY) { 666 SMSC_TRACE(pdata, hw, "Forcing internal PHY"); 667 pdata->using_extphy = 0; 668 } else if (pdata->config.flags & SMSC911X_FORCE_EXTERNAL_PHY) { 669 SMSC_TRACE(pdata, hw, "Forcing external PHY"); 670 smsc911x_phy_enable_external(pdata); 671 pdata->using_extphy = 1; 672 } else if (hwcfg & HW_CFG_EXT_PHY_DET_) { 673 SMSC_TRACE(pdata, hw, 674 "HW_CFG EXT_PHY_DET set, using external PHY"); 675 smsc911x_phy_enable_external(pdata); 676 pdata->using_extphy = 1; 677 } else { 678 SMSC_TRACE(pdata, hw, 679 "HW_CFG EXT_PHY_DET clear, using internal PHY"); 680 pdata->using_extphy = 0; 681 } 682 } 683 684 /* Fetches a tx status out of the status fifo */ 685 static unsigned int smsc911x_tx_get_txstatus(struct smsc911x_data *pdata) 686 { 687 unsigned int result = 688 smsc911x_reg_read(pdata, TX_FIFO_INF) & TX_FIFO_INF_TSUSED_; 689 690 if (result != 0) 691 result = smsc911x_reg_read(pdata, TX_STATUS_FIFO); 692 693 return result; 694 } 695 696 /* Fetches the next rx status */ 697 static unsigned int smsc911x_rx_get_rxstatus(struct smsc911x_data *pdata) 698 { 699 unsigned int result = 700 smsc911x_reg_read(pdata, RX_FIFO_INF) & RX_FIFO_INF_RXSUSED_; 701 702 if (result != 0) 703 result = smsc911x_reg_read(pdata, RX_STATUS_FIFO); 704 705 return result; 706 } 707 708 #ifdef USE_PHY_WORK_AROUND 709 static int smsc911x_phy_check_loopbackpkt(struct smsc911x_data *pdata) 710 { 711 unsigned int tries; 712 u32 wrsz; 713 u32 rdsz; 714 ulong bufp; 715 716 for (tries = 0; tries < 10; tries++) { 717 unsigned int txcmd_a; 718 unsigned int txcmd_b; 719 unsigned int status; 720 unsigned int pktlength; 721 unsigned int i; 722 723 /* Zero-out rx packet memory */ 724 memset(pdata->loopback_rx_pkt, 0, MIN_PACKET_SIZE); 725 726 /* Write tx packet to 118 */ 727 txcmd_a = (u32)((ulong)pdata->loopback_tx_pkt & 0x03) << 16; 728 txcmd_a |= TX_CMD_A_FIRST_SEG_ | TX_CMD_A_LAST_SEG_; 729 txcmd_a |= MIN_PACKET_SIZE; 730 731 txcmd_b = MIN_PACKET_SIZE << 16 | MIN_PACKET_SIZE; 732 733 smsc911x_reg_write(pdata, TX_DATA_FIFO, txcmd_a); 734 smsc911x_reg_write(pdata, TX_DATA_FIFO, txcmd_b); 735 736 bufp = (ulong)pdata->loopback_tx_pkt & (~0x3); 737 wrsz = MIN_PACKET_SIZE + 3; 738 wrsz += (u32)((ulong)pdata->loopback_tx_pkt & 0x3); 739 wrsz >>= 2; 740 741 pdata->ops->tx_writefifo(pdata, (unsigned int *)bufp, wrsz); 742 743 /* Wait till transmit is done */ 744 i = 60; 745 do { 746 udelay(5); 747 status = smsc911x_tx_get_txstatus(pdata); 748 } while ((i--) && (!status)); 749 750 if (!status) { 751 SMSC_WARN(pdata, hw, 752 "Failed to transmit during loopback test"); 753 continue; 754 } 755 if (status & TX_STS_ES_) { 756 SMSC_WARN(pdata, hw, 757 "Transmit encountered errors during loopback test"); 758 continue; 759 } 760 761 /* Wait till receive is done */ 762 i = 60; 763 do { 764 udelay(5); 765 status = smsc911x_rx_get_rxstatus(pdata); 766 } while ((i--) && (!status)); 767 768 if (!status) { 769 SMSC_WARN(pdata, hw, 770 "Failed to receive during loopback test"); 771 continue; 772 } 773 if (status & RX_STS_ES_) { 774 SMSC_WARN(pdata, hw, 775 "Receive encountered errors during loopback test"); 776 continue; 777 } 778 779 pktlength = ((status & 0x3FFF0000UL) >> 16); 780 bufp = (ulong)pdata->loopback_rx_pkt; 781 rdsz = pktlength + 3; 782 rdsz += (u32)((ulong)pdata->loopback_rx_pkt & 0x3); 783 rdsz >>= 2; 784 785 pdata->ops->rx_readfifo(pdata, (unsigned int *)bufp, rdsz); 786 787 if (pktlength != (MIN_PACKET_SIZE + 4)) { 788 SMSC_WARN(pdata, hw, "Unexpected packet size " 789 "during loop back test, size=%d, will retry", 790 pktlength); 791 } else { 792 unsigned int j; 793 int mismatch = 0; 794 for (j = 0; j < MIN_PACKET_SIZE; j++) { 795 if (pdata->loopback_tx_pkt[j] 796 != pdata->loopback_rx_pkt[j]) { 797 mismatch = 1; 798 break; 799 } 800 } 801 if (!mismatch) { 802 SMSC_TRACE(pdata, hw, "Successfully verified " 803 "loopback packet"); 804 return 0; 805 } else { 806 SMSC_WARN(pdata, hw, "Data mismatch " 807 "during loop back test, will retry"); 808 } 809 } 810 } 811 812 return -EIO; 813 } 814 815 static int smsc911x_phy_reset(struct smsc911x_data *pdata) 816 { 817 unsigned int temp; 818 unsigned int i = 100000; 819 820 temp = smsc911x_reg_read(pdata, PMT_CTRL); 821 smsc911x_reg_write(pdata, PMT_CTRL, temp | PMT_CTRL_PHY_RST_); 822 do { 823 msleep(1); 824 temp = smsc911x_reg_read(pdata, PMT_CTRL); 825 } while ((i--) && (temp & PMT_CTRL_PHY_RST_)); 826 827 if (unlikely(temp & PMT_CTRL_PHY_RST_)) { 828 SMSC_WARN(pdata, hw, "PHY reset failed to complete"); 829 return -EIO; 830 } 831 /* Extra delay required because the phy may not be completed with 832 * its reset when BMCR_RESET is cleared. Specs say 256 uS is 833 * enough delay but using 1ms here to be safe */ 834 msleep(1); 835 836 return 0; 837 } 838 839 static int smsc911x_phy_loopbacktest(struct net_device *dev) 840 { 841 struct smsc911x_data *pdata = netdev_priv(dev); 842 struct phy_device *phy_dev = dev->phydev; 843 int result = -EIO; 844 unsigned int i, val; 845 unsigned long flags; 846 847 /* Initialise tx packet using broadcast destination address */ 848 eth_broadcast_addr(pdata->loopback_tx_pkt); 849 850 /* Use incrementing source address */ 851 for (i = 6; i < 12; i++) 852 pdata->loopback_tx_pkt[i] = (char)i; 853 854 /* Set length type field */ 855 pdata->loopback_tx_pkt[12] = 0x00; 856 pdata->loopback_tx_pkt[13] = 0x00; 857 858 for (i = 14; i < MIN_PACKET_SIZE; i++) 859 pdata->loopback_tx_pkt[i] = (char)i; 860 861 val = smsc911x_reg_read(pdata, HW_CFG); 862 val &= HW_CFG_TX_FIF_SZ_; 863 val |= HW_CFG_SF_; 864 smsc911x_reg_write(pdata, HW_CFG, val); 865 866 smsc911x_reg_write(pdata, TX_CFG, TX_CFG_TX_ON_); 867 smsc911x_reg_write(pdata, RX_CFG, 868 (u32)((ulong)pdata->loopback_rx_pkt & 0x03) << 8); 869 870 for (i = 0; i < 10; i++) { 871 /* Set PHY to 10/FD, no ANEG, and loopback mode */ 872 smsc911x_mii_write(phy_dev->mdio.bus, phy_dev->mdio.addr, 873 MII_BMCR, BMCR_LOOPBACK | BMCR_FULLDPLX); 874 875 /* Enable MAC tx/rx, FD */ 876 spin_lock_irqsave(&pdata->mac_lock, flags); 877 smsc911x_mac_write(pdata, MAC_CR, MAC_CR_FDPX_ 878 | MAC_CR_TXEN_ | MAC_CR_RXEN_); 879 spin_unlock_irqrestore(&pdata->mac_lock, flags); 880 881 if (smsc911x_phy_check_loopbackpkt(pdata) == 0) { 882 result = 0; 883 break; 884 } 885 pdata->resetcount++; 886 887 /* Disable MAC rx */ 888 spin_lock_irqsave(&pdata->mac_lock, flags); 889 smsc911x_mac_write(pdata, MAC_CR, 0); 890 spin_unlock_irqrestore(&pdata->mac_lock, flags); 891 892 smsc911x_phy_reset(pdata); 893 } 894 895 /* Disable MAC */ 896 spin_lock_irqsave(&pdata->mac_lock, flags); 897 smsc911x_mac_write(pdata, MAC_CR, 0); 898 spin_unlock_irqrestore(&pdata->mac_lock, flags); 899 900 /* Cancel PHY loopback mode */ 901 smsc911x_mii_write(phy_dev->mdio.bus, phy_dev->mdio.addr, MII_BMCR, 0); 902 903 smsc911x_reg_write(pdata, TX_CFG, 0); 904 smsc911x_reg_write(pdata, RX_CFG, 0); 905 906 return result; 907 } 908 #endif /* USE_PHY_WORK_AROUND */ 909 910 static void smsc911x_phy_update_flowcontrol(struct smsc911x_data *pdata) 911 { 912 struct net_device *ndev = pdata->dev; 913 struct phy_device *phy_dev = ndev->phydev; 914 u32 afc = smsc911x_reg_read(pdata, AFC_CFG); 915 u32 flow; 916 unsigned long flags; 917 918 if (phy_dev->duplex == DUPLEX_FULL) { 919 u16 lcladv = phy_read(phy_dev, MII_ADVERTISE); 920 u16 rmtadv = phy_read(phy_dev, MII_LPA); 921 u8 cap = mii_resolve_flowctrl_fdx(lcladv, rmtadv); 922 923 if (cap & FLOW_CTRL_RX) 924 flow = 0xFFFF0002; 925 else 926 flow = 0; 927 928 if (cap & FLOW_CTRL_TX) 929 afc |= 0xF; 930 else 931 afc &= ~0xF; 932 933 SMSC_TRACE(pdata, hw, "rx pause %s, tx pause %s", 934 (cap & FLOW_CTRL_RX ? "enabled" : "disabled"), 935 (cap & FLOW_CTRL_TX ? "enabled" : "disabled")); 936 } else { 937 SMSC_TRACE(pdata, hw, "half duplex"); 938 flow = 0; 939 afc |= 0xF; 940 } 941 942 spin_lock_irqsave(&pdata->mac_lock, flags); 943 smsc911x_mac_write(pdata, FLOW, flow); 944 spin_unlock_irqrestore(&pdata->mac_lock, flags); 945 946 smsc911x_reg_write(pdata, AFC_CFG, afc); 947 } 948 949 /* Update link mode if anything has changed. Called periodically when the 950 * PHY is in polling mode, even if nothing has changed. */ 951 static void smsc911x_phy_adjust_link(struct net_device *dev) 952 { 953 struct smsc911x_data *pdata = netdev_priv(dev); 954 struct phy_device *phy_dev = dev->phydev; 955 unsigned long flags; 956 int carrier; 957 958 if (phy_dev->duplex != pdata->last_duplex) { 959 unsigned int mac_cr; 960 SMSC_TRACE(pdata, hw, "duplex state has changed"); 961 962 spin_lock_irqsave(&pdata->mac_lock, flags); 963 mac_cr = smsc911x_mac_read(pdata, MAC_CR); 964 if (phy_dev->duplex) { 965 SMSC_TRACE(pdata, hw, 966 "configuring for full duplex mode"); 967 mac_cr |= MAC_CR_FDPX_; 968 } else { 969 SMSC_TRACE(pdata, hw, 970 "configuring for half duplex mode"); 971 mac_cr &= ~MAC_CR_FDPX_; 972 } 973 smsc911x_mac_write(pdata, MAC_CR, mac_cr); 974 spin_unlock_irqrestore(&pdata->mac_lock, flags); 975 976 smsc911x_phy_update_flowcontrol(pdata); 977 pdata->last_duplex = phy_dev->duplex; 978 } 979 980 carrier = netif_carrier_ok(dev); 981 if (carrier != pdata->last_carrier) { 982 SMSC_TRACE(pdata, hw, "carrier state has changed"); 983 if (carrier) { 984 SMSC_TRACE(pdata, hw, "configuring for carrier OK"); 985 if ((pdata->gpio_orig_setting & GPIO_CFG_LED1_EN_) && 986 (!pdata->using_extphy)) { 987 /* Restore original GPIO configuration */ 988 pdata->gpio_setting = pdata->gpio_orig_setting; 989 smsc911x_reg_write(pdata, GPIO_CFG, 990 pdata->gpio_setting); 991 } 992 } else { 993 SMSC_TRACE(pdata, hw, "configuring for no carrier"); 994 /* Check global setting that LED1 995 * usage is 10/100 indicator */ 996 pdata->gpio_setting = smsc911x_reg_read(pdata, 997 GPIO_CFG); 998 if ((pdata->gpio_setting & GPIO_CFG_LED1_EN_) && 999 (!pdata->using_extphy)) { 1000 /* Force 10/100 LED off, after saving 1001 * original GPIO configuration */ 1002 pdata->gpio_orig_setting = pdata->gpio_setting; 1003 1004 pdata->gpio_setting &= ~GPIO_CFG_LED1_EN_; 1005 pdata->gpio_setting |= (GPIO_CFG_GPIOBUF0_ 1006 | GPIO_CFG_GPIODIR0_ 1007 | GPIO_CFG_GPIOD0_); 1008 smsc911x_reg_write(pdata, GPIO_CFG, 1009 pdata->gpio_setting); 1010 } 1011 } 1012 pdata->last_carrier = carrier; 1013 } 1014 } 1015 1016 static int smsc911x_mii_probe(struct net_device *dev) 1017 { 1018 struct smsc911x_data *pdata = netdev_priv(dev); 1019 struct phy_device *phydev = NULL; 1020 int ret; 1021 1022 /* find the first phy */ 1023 phydev = phy_find_first(pdata->mii_bus); 1024 if (!phydev) { 1025 netdev_err(dev, "no PHY found\n"); 1026 return -ENODEV; 1027 } 1028 1029 SMSC_TRACE(pdata, probe, "PHY: addr %d, phy_id 0x%08X", 1030 phydev->mdio.addr, phydev->phy_id); 1031 1032 ret = phy_connect_direct(dev, phydev, &smsc911x_phy_adjust_link, 1033 pdata->config.phy_interface); 1034 1035 if (ret) { 1036 netdev_err(dev, "Could not attach to PHY\n"); 1037 return ret; 1038 } 1039 1040 /* Indicate that the MAC is responsible for managing PHY PM */ 1041 phydev->mac_managed_pm = true; 1042 phy_attached_info(phydev); 1043 1044 phy_set_max_speed(phydev, SPEED_100); 1045 1046 /* mask with MAC supported features */ 1047 phy_support_asym_pause(phydev); 1048 1049 pdata->last_duplex = -1; 1050 pdata->last_carrier = -1; 1051 1052 #ifdef USE_PHY_WORK_AROUND 1053 if (smsc911x_phy_loopbacktest(dev) < 0) { 1054 SMSC_WARN(pdata, hw, "Failed Loop Back Test"); 1055 phy_disconnect(phydev); 1056 return -ENODEV; 1057 } 1058 SMSC_TRACE(pdata, hw, "Passed Loop Back Test"); 1059 #endif /* USE_PHY_WORK_AROUND */ 1060 1061 SMSC_TRACE(pdata, hw, "phy initialised successfully"); 1062 return 0; 1063 } 1064 1065 static int smsc911x_mii_init(struct platform_device *pdev, 1066 struct net_device *dev) 1067 { 1068 struct smsc911x_data *pdata = netdev_priv(dev); 1069 int err = -ENXIO; 1070 1071 pdata->mii_bus = mdiobus_alloc(); 1072 if (!pdata->mii_bus) { 1073 err = -ENOMEM; 1074 goto err_out_1; 1075 } 1076 1077 pdata->mii_bus->name = SMSC_MDIONAME; 1078 snprintf(pdata->mii_bus->id, MII_BUS_ID_SIZE, "%s-%x", 1079 pdev->name, pdev->id); 1080 pdata->mii_bus->priv = pdata; 1081 pdata->mii_bus->read = smsc911x_mii_read; 1082 pdata->mii_bus->write = smsc911x_mii_write; 1083 1084 pdata->mii_bus->parent = &pdev->dev; 1085 1086 switch (pdata->idrev & 0xFFFF0000) { 1087 case 0x01170000: 1088 case 0x01150000: 1089 case 0x117A0000: 1090 case 0x115A0000: 1091 /* External PHY supported, try to autodetect */ 1092 smsc911x_phy_initialise_external(pdata); 1093 break; 1094 default: 1095 SMSC_TRACE(pdata, hw, "External PHY is not supported, " 1096 "using internal PHY"); 1097 pdata->using_extphy = 0; 1098 break; 1099 } 1100 1101 if (!pdata->using_extphy) { 1102 /* Mask all PHYs except ID 1 (internal) */ 1103 pdata->mii_bus->phy_mask = ~(1 << 1); 1104 } 1105 1106 if (mdiobus_register(pdata->mii_bus)) { 1107 SMSC_WARN(pdata, probe, "Error registering mii bus"); 1108 goto err_out_free_bus_2; 1109 } 1110 1111 return 0; 1112 1113 err_out_free_bus_2: 1114 mdiobus_free(pdata->mii_bus); 1115 err_out_1: 1116 return err; 1117 } 1118 1119 /* Gets the number of tx statuses in the fifo */ 1120 static unsigned int smsc911x_tx_get_txstatcount(struct smsc911x_data *pdata) 1121 { 1122 return (smsc911x_reg_read(pdata, TX_FIFO_INF) 1123 & TX_FIFO_INF_TSUSED_) >> 16; 1124 } 1125 1126 /* Reads tx statuses and increments counters where necessary */ 1127 static void smsc911x_tx_update_txcounters(struct net_device *dev) 1128 { 1129 struct smsc911x_data *pdata = netdev_priv(dev); 1130 unsigned int tx_stat; 1131 1132 while ((tx_stat = smsc911x_tx_get_txstatus(pdata)) != 0) { 1133 if (unlikely(tx_stat & 0x80000000)) { 1134 /* In this driver the packet tag is used as the packet 1135 * length. Since a packet length can never reach the 1136 * size of 0x8000, this bit is reserved. It is worth 1137 * noting that the "reserved bit" in the warning above 1138 * does not reference a hardware defined reserved bit 1139 * but rather a driver defined one. 1140 */ 1141 SMSC_WARN(pdata, hw, "Packet tag reserved bit is high"); 1142 } else { 1143 if (unlikely(tx_stat & TX_STS_ES_)) { 1144 dev->stats.tx_errors++; 1145 } else { 1146 dev->stats.tx_packets++; 1147 dev->stats.tx_bytes += (tx_stat >> 16); 1148 } 1149 if (unlikely(tx_stat & TX_STS_EXCESS_COL_)) { 1150 dev->stats.collisions += 16; 1151 dev->stats.tx_aborted_errors += 1; 1152 } else { 1153 dev->stats.collisions += 1154 ((tx_stat >> 3) & 0xF); 1155 } 1156 if (unlikely(tx_stat & TX_STS_LOST_CARRIER_)) 1157 dev->stats.tx_carrier_errors += 1; 1158 if (unlikely(tx_stat & TX_STS_LATE_COL_)) { 1159 dev->stats.collisions++; 1160 dev->stats.tx_aborted_errors++; 1161 } 1162 } 1163 } 1164 } 1165 1166 /* Increments the Rx error counters */ 1167 static void 1168 smsc911x_rx_counterrors(struct net_device *dev, unsigned int rxstat) 1169 { 1170 int crc_err = 0; 1171 1172 if (unlikely(rxstat & RX_STS_ES_)) { 1173 dev->stats.rx_errors++; 1174 if (unlikely(rxstat & RX_STS_CRC_ERR_)) { 1175 dev->stats.rx_crc_errors++; 1176 crc_err = 1; 1177 } 1178 } 1179 if (likely(!crc_err)) { 1180 if (unlikely((rxstat & RX_STS_FRAME_TYPE_) && 1181 (rxstat & RX_STS_LENGTH_ERR_))) 1182 dev->stats.rx_length_errors++; 1183 if (rxstat & RX_STS_MCAST_) 1184 dev->stats.multicast++; 1185 } 1186 } 1187 1188 /* Quickly dumps bad packets */ 1189 static void 1190 smsc911x_rx_fastforward(struct smsc911x_data *pdata, unsigned int pktwords) 1191 { 1192 if (likely(pktwords >= 4)) { 1193 unsigned int timeout = 500; 1194 unsigned int val; 1195 smsc911x_reg_write(pdata, RX_DP_CTRL, RX_DP_CTRL_RX_FFWD_); 1196 do { 1197 udelay(1); 1198 val = smsc911x_reg_read(pdata, RX_DP_CTRL); 1199 } while ((val & RX_DP_CTRL_RX_FFWD_) && --timeout); 1200 1201 if (unlikely(timeout == 0)) 1202 SMSC_WARN(pdata, hw, "Timed out waiting for " 1203 "RX FFWD to finish, RX_DP_CTRL: 0x%08X", val); 1204 } else { 1205 while (pktwords--) 1206 smsc911x_reg_read(pdata, RX_DATA_FIFO); 1207 } 1208 } 1209 1210 /* NAPI poll function */ 1211 static int smsc911x_poll(struct napi_struct *napi, int budget) 1212 { 1213 struct smsc911x_data *pdata = 1214 container_of(napi, struct smsc911x_data, napi); 1215 struct net_device *dev = pdata->dev; 1216 int npackets = 0; 1217 1218 while (npackets < budget) { 1219 unsigned int pktlength; 1220 unsigned int pktwords; 1221 struct sk_buff *skb; 1222 unsigned int rxstat = smsc911x_rx_get_rxstatus(pdata); 1223 1224 if (!rxstat) { 1225 unsigned int temp; 1226 /* We processed all packets available. Tell NAPI it can 1227 * stop polling then re-enable rx interrupts */ 1228 smsc911x_reg_write(pdata, INT_STS, INT_STS_RSFL_); 1229 napi_complete(napi); 1230 temp = smsc911x_reg_read(pdata, INT_EN); 1231 temp |= INT_EN_RSFL_EN_; 1232 smsc911x_reg_write(pdata, INT_EN, temp); 1233 break; 1234 } 1235 1236 /* Count packet for NAPI scheduling, even if it has an error. 1237 * Error packets still require cycles to discard */ 1238 npackets++; 1239 1240 pktlength = ((rxstat & 0x3FFF0000) >> 16); 1241 pktwords = (pktlength + NET_IP_ALIGN + 3) >> 2; 1242 smsc911x_rx_counterrors(dev, rxstat); 1243 1244 if (unlikely(rxstat & RX_STS_ES_)) { 1245 SMSC_WARN(pdata, rx_err, 1246 "Discarding packet with error bit set"); 1247 /* Packet has an error, discard it and continue with 1248 * the next */ 1249 smsc911x_rx_fastforward(pdata, pktwords); 1250 dev->stats.rx_dropped++; 1251 continue; 1252 } 1253 1254 skb = netdev_alloc_skb(dev, pktwords << 2); 1255 if (unlikely(!skb)) { 1256 SMSC_WARN(pdata, rx_err, 1257 "Unable to allocate skb for rx packet"); 1258 /* Drop the packet and stop this polling iteration */ 1259 smsc911x_rx_fastforward(pdata, pktwords); 1260 dev->stats.rx_dropped++; 1261 break; 1262 } 1263 1264 pdata->ops->rx_readfifo(pdata, 1265 (unsigned int *)skb->data, pktwords); 1266 1267 /* Align IP on 16B boundary */ 1268 skb_reserve(skb, NET_IP_ALIGN); 1269 skb_put(skb, pktlength - 4); 1270 skb->protocol = eth_type_trans(skb, dev); 1271 skb_checksum_none_assert(skb); 1272 netif_receive_skb(skb); 1273 1274 /* Update counters */ 1275 dev->stats.rx_packets++; 1276 dev->stats.rx_bytes += (pktlength - 4); 1277 } 1278 1279 /* Return total received packets */ 1280 return npackets; 1281 } 1282 1283 /* Returns hash bit number for given MAC address 1284 * Example: 1285 * 01 00 5E 00 00 01 -> returns bit number 31 */ 1286 static unsigned int smsc911x_hash(char addr[ETH_ALEN]) 1287 { 1288 return (ether_crc(ETH_ALEN, addr) >> 26) & 0x3f; 1289 } 1290 1291 static void smsc911x_rx_multicast_update(struct smsc911x_data *pdata) 1292 { 1293 /* Performs the multicast & mac_cr update. This is called when 1294 * safe on the current hardware, and with the mac_lock held */ 1295 unsigned int mac_cr; 1296 1297 SMSC_ASSERT_MAC_LOCK(pdata); 1298 1299 mac_cr = smsc911x_mac_read(pdata, MAC_CR); 1300 mac_cr |= pdata->set_bits_mask; 1301 mac_cr &= ~(pdata->clear_bits_mask); 1302 smsc911x_mac_write(pdata, MAC_CR, mac_cr); 1303 smsc911x_mac_write(pdata, HASHH, pdata->hashhi); 1304 smsc911x_mac_write(pdata, HASHL, pdata->hashlo); 1305 SMSC_TRACE(pdata, hw, "maccr 0x%08X, HASHH 0x%08X, HASHL 0x%08X", 1306 mac_cr, pdata->hashhi, pdata->hashlo); 1307 } 1308 1309 static void smsc911x_rx_multicast_update_workaround(struct smsc911x_data *pdata) 1310 { 1311 unsigned int mac_cr; 1312 1313 /* This function is only called for older LAN911x devices 1314 * (revA or revB), where MAC_CR, HASHH and HASHL should not 1315 * be modified during Rx - newer devices immediately update the 1316 * registers. 1317 * 1318 * This is called from interrupt context */ 1319 1320 spin_lock(&pdata->mac_lock); 1321 1322 /* Check Rx has stopped */ 1323 if (smsc911x_mac_read(pdata, MAC_CR) & MAC_CR_RXEN_) 1324 SMSC_WARN(pdata, drv, "Rx not stopped"); 1325 1326 /* Perform the update - safe to do now Rx has stopped */ 1327 smsc911x_rx_multicast_update(pdata); 1328 1329 /* Re-enable Rx */ 1330 mac_cr = smsc911x_mac_read(pdata, MAC_CR); 1331 mac_cr |= MAC_CR_RXEN_; 1332 smsc911x_mac_write(pdata, MAC_CR, mac_cr); 1333 1334 pdata->multicast_update_pending = 0; 1335 1336 spin_unlock(&pdata->mac_lock); 1337 } 1338 1339 static int smsc911x_phy_general_power_up(struct smsc911x_data *pdata) 1340 { 1341 struct net_device *ndev = pdata->dev; 1342 struct phy_device *phy_dev = ndev->phydev; 1343 int rc = 0; 1344 1345 if (!phy_dev) 1346 return rc; 1347 1348 /* If the internal PHY is in General Power-Down mode, all, except the 1349 * management interface, is powered-down and stays in that condition as 1350 * long as Phy register bit 0.11 is HIGH. 1351 * 1352 * In that case, clear the bit 0.11, so the PHY powers up and we can 1353 * access to the phy registers. 1354 */ 1355 rc = phy_read(phy_dev, MII_BMCR); 1356 if (rc < 0) { 1357 SMSC_WARN(pdata, drv, "Failed reading PHY control reg"); 1358 return rc; 1359 } 1360 1361 /* If the PHY general power-down bit is not set is not necessary to 1362 * disable the general power down-mode. 1363 */ 1364 if (rc & BMCR_PDOWN) { 1365 rc = phy_write(phy_dev, MII_BMCR, rc & ~BMCR_PDOWN); 1366 if (rc < 0) { 1367 SMSC_WARN(pdata, drv, "Failed writing PHY control reg"); 1368 return rc; 1369 } 1370 1371 usleep_range(1000, 1500); 1372 } 1373 1374 return 0; 1375 } 1376 1377 static int smsc911x_phy_disable_energy_detect(struct smsc911x_data *pdata) 1378 { 1379 struct net_device *ndev = pdata->dev; 1380 struct phy_device *phy_dev = ndev->phydev; 1381 int rc = 0; 1382 1383 if (!phy_dev) 1384 return rc; 1385 1386 rc = phy_read(phy_dev, MII_LAN83C185_CTRL_STATUS); 1387 1388 if (rc < 0) { 1389 SMSC_WARN(pdata, drv, "Failed reading PHY control reg"); 1390 return rc; 1391 } 1392 1393 /* Only disable if energy detect mode is already enabled */ 1394 if (rc & MII_LAN83C185_EDPWRDOWN) { 1395 /* Disable energy detect mode for this SMSC Transceivers */ 1396 rc = phy_write(phy_dev, MII_LAN83C185_CTRL_STATUS, 1397 rc & (~MII_LAN83C185_EDPWRDOWN)); 1398 1399 if (rc < 0) { 1400 SMSC_WARN(pdata, drv, "Failed writing PHY control reg"); 1401 return rc; 1402 } 1403 /* Allow PHY to wakeup */ 1404 mdelay(2); 1405 } 1406 1407 return 0; 1408 } 1409 1410 static int smsc911x_phy_enable_energy_detect(struct smsc911x_data *pdata) 1411 { 1412 struct net_device *ndev = pdata->dev; 1413 struct phy_device *phy_dev = ndev->phydev; 1414 int rc = 0; 1415 1416 if (!phy_dev) 1417 return rc; 1418 1419 rc = phy_read(phy_dev, MII_LAN83C185_CTRL_STATUS); 1420 1421 if (rc < 0) { 1422 SMSC_WARN(pdata, drv, "Failed reading PHY control reg"); 1423 return rc; 1424 } 1425 1426 /* Only enable if energy detect mode is already disabled */ 1427 if (!(rc & MII_LAN83C185_EDPWRDOWN)) { 1428 /* Enable energy detect mode for this SMSC Transceivers */ 1429 rc = phy_write(phy_dev, MII_LAN83C185_CTRL_STATUS, 1430 rc | MII_LAN83C185_EDPWRDOWN); 1431 1432 if (rc < 0) { 1433 SMSC_WARN(pdata, drv, "Failed writing PHY control reg"); 1434 return rc; 1435 } 1436 } 1437 return 0; 1438 } 1439 1440 static int smsc911x_soft_reset(struct smsc911x_data *pdata) 1441 { 1442 unsigned int timeout; 1443 unsigned int temp; 1444 int ret; 1445 unsigned int reset_offset = HW_CFG; 1446 unsigned int reset_mask = HW_CFG_SRST_; 1447 1448 /* 1449 * Make sure to power-up the PHY chip before doing a reset, otherwise 1450 * the reset fails. 1451 */ 1452 ret = smsc911x_phy_general_power_up(pdata); 1453 if (ret) { 1454 SMSC_WARN(pdata, drv, "Failed to power-up the PHY chip"); 1455 return ret; 1456 } 1457 1458 /* 1459 * LAN9210/LAN9211/LAN9220/LAN9221 chips have an internal PHY that 1460 * are initialized in a Energy Detect Power-Down mode that prevents 1461 * the MAC chip to be software reseted. So we have to wakeup the PHY 1462 * before. 1463 */ 1464 if (pdata->generation == 4) { 1465 ret = smsc911x_phy_disable_energy_detect(pdata); 1466 1467 if (ret) { 1468 SMSC_WARN(pdata, drv, "Failed to wakeup the PHY chip"); 1469 return ret; 1470 } 1471 } 1472 1473 if ((pdata->idrev & 0xFFFF0000) == LAN9250) { 1474 /* special reset for LAN9250 */ 1475 reset_offset = RESET_CTL; 1476 reset_mask = RESET_CTL_DIGITAL_RST_; 1477 } 1478 1479 /* Reset the LAN911x */ 1480 smsc911x_reg_write(pdata, reset_offset, reset_mask); 1481 1482 /* verify reset bit is cleared */ 1483 timeout = 10; 1484 do { 1485 udelay(10); 1486 temp = smsc911x_reg_read(pdata, reset_offset); 1487 } while ((--timeout) && (temp & reset_mask)); 1488 1489 if (unlikely(temp & reset_mask)) { 1490 SMSC_WARN(pdata, drv, "Failed to complete reset"); 1491 return -EIO; 1492 } 1493 1494 if (pdata->generation == 4) { 1495 ret = smsc911x_phy_enable_energy_detect(pdata); 1496 1497 if (ret) { 1498 SMSC_WARN(pdata, drv, "Failed to wakeup the PHY chip"); 1499 return ret; 1500 } 1501 } 1502 1503 return 0; 1504 } 1505 1506 /* Sets the device MAC address to dev_addr, called with mac_lock held */ 1507 static void 1508 smsc911x_set_hw_mac_address(struct smsc911x_data *pdata, const u8 dev_addr[6]) 1509 { 1510 u32 mac_high16 = (dev_addr[5] << 8) | dev_addr[4]; 1511 u32 mac_low32 = (dev_addr[3] << 24) | (dev_addr[2] << 16) | 1512 (dev_addr[1] << 8) | dev_addr[0]; 1513 1514 SMSC_ASSERT_MAC_LOCK(pdata); 1515 1516 smsc911x_mac_write(pdata, ADDRH, mac_high16); 1517 smsc911x_mac_write(pdata, ADDRL, mac_low32); 1518 } 1519 1520 static void smsc911x_disable_irq_chip(struct net_device *dev) 1521 { 1522 struct smsc911x_data *pdata = netdev_priv(dev); 1523 1524 smsc911x_reg_write(pdata, INT_EN, 0); 1525 smsc911x_reg_write(pdata, INT_STS, 0xFFFFFFFF); 1526 } 1527 1528 static irqreturn_t smsc911x_irqhandler(int irq, void *dev_id) 1529 { 1530 struct net_device *dev = dev_id; 1531 struct smsc911x_data *pdata = netdev_priv(dev); 1532 u32 intsts = smsc911x_reg_read(pdata, INT_STS); 1533 u32 inten = smsc911x_reg_read(pdata, INT_EN); 1534 int serviced = IRQ_NONE; 1535 u32 temp; 1536 1537 if (unlikely(intsts & inten & INT_STS_SW_INT_)) { 1538 temp = smsc911x_reg_read(pdata, INT_EN); 1539 temp &= (~INT_EN_SW_INT_EN_); 1540 smsc911x_reg_write(pdata, INT_EN, temp); 1541 smsc911x_reg_write(pdata, INT_STS, INT_STS_SW_INT_); 1542 pdata->software_irq_signal = 1; 1543 smp_wmb(); 1544 serviced = IRQ_HANDLED; 1545 } 1546 1547 if (unlikely(intsts & inten & INT_STS_RXSTOP_INT_)) { 1548 /* Called when there is a multicast update scheduled and 1549 * it is now safe to complete the update */ 1550 SMSC_TRACE(pdata, intr, "RX Stop interrupt"); 1551 smsc911x_reg_write(pdata, INT_STS, INT_STS_RXSTOP_INT_); 1552 if (pdata->multicast_update_pending) 1553 smsc911x_rx_multicast_update_workaround(pdata); 1554 serviced = IRQ_HANDLED; 1555 } 1556 1557 if (intsts & inten & INT_STS_TDFA_) { 1558 temp = smsc911x_reg_read(pdata, FIFO_INT); 1559 temp |= FIFO_INT_TX_AVAIL_LEVEL_; 1560 smsc911x_reg_write(pdata, FIFO_INT, temp); 1561 smsc911x_reg_write(pdata, INT_STS, INT_STS_TDFA_); 1562 netif_wake_queue(dev); 1563 serviced = IRQ_HANDLED; 1564 } 1565 1566 if (unlikely(intsts & inten & INT_STS_RXE_)) { 1567 SMSC_TRACE(pdata, intr, "RX Error interrupt"); 1568 smsc911x_reg_write(pdata, INT_STS, INT_STS_RXE_); 1569 serviced = IRQ_HANDLED; 1570 } 1571 1572 if (likely(intsts & inten & INT_STS_RSFL_)) { 1573 if (likely(napi_schedule_prep(&pdata->napi))) { 1574 /* Disable Rx interrupts */ 1575 temp = smsc911x_reg_read(pdata, INT_EN); 1576 temp &= (~INT_EN_RSFL_EN_); 1577 smsc911x_reg_write(pdata, INT_EN, temp); 1578 /* Schedule a NAPI poll */ 1579 __napi_schedule(&pdata->napi); 1580 } else { 1581 SMSC_WARN(pdata, rx_err, "napi_schedule_prep failed"); 1582 } 1583 serviced = IRQ_HANDLED; 1584 } 1585 1586 return serviced; 1587 } 1588 1589 static int smsc911x_open(struct net_device *dev) 1590 { 1591 struct smsc911x_data *pdata = netdev_priv(dev); 1592 unsigned int timeout; 1593 unsigned int temp; 1594 unsigned int intcfg; 1595 int retval; 1596 int irq_flags; 1597 1598 pm_runtime_get_sync(dev->dev.parent); 1599 1600 /* find and start the given phy */ 1601 if (!dev->phydev) { 1602 retval = smsc911x_mii_probe(dev); 1603 if (retval < 0) { 1604 SMSC_WARN(pdata, probe, "Error starting phy"); 1605 goto out; 1606 } 1607 } 1608 1609 /* Reset the LAN911x */ 1610 retval = smsc911x_soft_reset(pdata); 1611 if (retval) { 1612 SMSC_WARN(pdata, hw, "soft reset failed"); 1613 goto mii_free_out; 1614 } 1615 1616 smsc911x_reg_write(pdata, HW_CFG, 0x00050000); 1617 smsc911x_reg_write(pdata, AFC_CFG, 0x006E3740); 1618 1619 /* Increase the legal frame size of VLAN tagged frames to 1522 bytes */ 1620 spin_lock_irq(&pdata->mac_lock); 1621 smsc911x_mac_write(pdata, VLAN1, ETH_P_8021Q); 1622 spin_unlock_irq(&pdata->mac_lock); 1623 1624 /* Make sure EEPROM has finished loading before setting GPIO_CFG */ 1625 timeout = 50; 1626 while ((smsc911x_reg_read(pdata, E2P_CMD) & E2P_CMD_EPC_BUSY_) && 1627 --timeout) { 1628 udelay(10); 1629 } 1630 1631 if (unlikely(timeout == 0)) 1632 SMSC_WARN(pdata, ifup, 1633 "Timed out waiting for EEPROM busy bit to clear"); 1634 1635 smsc911x_reg_write(pdata, GPIO_CFG, 0x70070000); 1636 1637 /* The soft reset above cleared the device's MAC address, 1638 * restore it from local copy (set in probe) */ 1639 spin_lock_irq(&pdata->mac_lock); 1640 smsc911x_set_hw_mac_address(pdata, dev->dev_addr); 1641 spin_unlock_irq(&pdata->mac_lock); 1642 1643 /* Initialise irqs, but leave all sources disabled */ 1644 smsc911x_disable_irq_chip(dev); 1645 1646 /* Set interrupt deassertion to 100uS */ 1647 intcfg = ((10 << 24) | INT_CFG_IRQ_EN_); 1648 1649 if (pdata->config.irq_polarity) { 1650 SMSC_TRACE(pdata, ifup, "irq polarity: active high"); 1651 intcfg |= INT_CFG_IRQ_POL_; 1652 } else { 1653 SMSC_TRACE(pdata, ifup, "irq polarity: active low"); 1654 } 1655 1656 if (pdata->config.irq_type) { 1657 SMSC_TRACE(pdata, ifup, "irq type: push-pull"); 1658 intcfg |= INT_CFG_IRQ_TYPE_; 1659 } else { 1660 SMSC_TRACE(pdata, ifup, "irq type: open drain"); 1661 } 1662 1663 smsc911x_reg_write(pdata, INT_CFG, intcfg); 1664 1665 SMSC_TRACE(pdata, ifup, "Testing irq handler using IRQ %d", dev->irq); 1666 pdata->software_irq_signal = 0; 1667 smp_wmb(); 1668 1669 irq_flags = irq_get_trigger_type(dev->irq); 1670 retval = request_irq(dev->irq, smsc911x_irqhandler, 1671 irq_flags | IRQF_SHARED, dev->name, dev); 1672 if (retval) { 1673 SMSC_WARN(pdata, probe, 1674 "Unable to claim requested irq: %d", dev->irq); 1675 goto mii_free_out; 1676 } 1677 1678 temp = smsc911x_reg_read(pdata, INT_EN); 1679 temp |= INT_EN_SW_INT_EN_; 1680 smsc911x_reg_write(pdata, INT_EN, temp); 1681 1682 timeout = 1000; 1683 while (timeout--) { 1684 if (pdata->software_irq_signal) 1685 break; 1686 msleep(1); 1687 } 1688 1689 if (!pdata->software_irq_signal) { 1690 netdev_warn(dev, "ISR failed signaling test (IRQ %d)\n", 1691 dev->irq); 1692 retval = -ENODEV; 1693 goto irq_stop_out; 1694 } 1695 SMSC_TRACE(pdata, ifup, "IRQ handler passed test using IRQ %d", 1696 dev->irq); 1697 1698 netdev_info(dev, "SMSC911x/921x identified at %#08lx, IRQ: %d\n", 1699 (unsigned long)pdata->ioaddr, dev->irq); 1700 1701 /* Reset the last known duplex and carrier */ 1702 pdata->last_duplex = -1; 1703 pdata->last_carrier = -1; 1704 1705 /* Bring the PHY up */ 1706 phy_start(dev->phydev); 1707 1708 temp = smsc911x_reg_read(pdata, HW_CFG); 1709 /* Preserve TX FIFO size and external PHY configuration */ 1710 temp &= (HW_CFG_TX_FIF_SZ_|0x00000FFF); 1711 temp |= HW_CFG_SF_; 1712 smsc911x_reg_write(pdata, HW_CFG, temp); 1713 1714 temp = smsc911x_reg_read(pdata, FIFO_INT); 1715 temp |= FIFO_INT_TX_AVAIL_LEVEL_; 1716 temp &= ~(FIFO_INT_RX_STS_LEVEL_); 1717 smsc911x_reg_write(pdata, FIFO_INT, temp); 1718 1719 /* set RX Data offset to 2 bytes for alignment */ 1720 smsc911x_reg_write(pdata, RX_CFG, (NET_IP_ALIGN << 8)); 1721 1722 /* enable NAPI polling before enabling RX interrupts */ 1723 napi_enable(&pdata->napi); 1724 1725 temp = smsc911x_reg_read(pdata, INT_EN); 1726 temp |= (INT_EN_TDFA_EN_ | INT_EN_RSFL_EN_ | INT_EN_RXSTOP_INT_EN_); 1727 smsc911x_reg_write(pdata, INT_EN, temp); 1728 1729 spin_lock_irq(&pdata->mac_lock); 1730 temp = smsc911x_mac_read(pdata, MAC_CR); 1731 temp |= (MAC_CR_TXEN_ | MAC_CR_RXEN_ | MAC_CR_HBDIS_); 1732 smsc911x_mac_write(pdata, MAC_CR, temp); 1733 spin_unlock_irq(&pdata->mac_lock); 1734 1735 smsc911x_reg_write(pdata, TX_CFG, TX_CFG_TX_ON_); 1736 1737 netif_start_queue(dev); 1738 return 0; 1739 1740 irq_stop_out: 1741 free_irq(dev->irq, dev); 1742 mii_free_out: 1743 phy_disconnect(dev->phydev); 1744 dev->phydev = NULL; 1745 out: 1746 pm_runtime_put(dev->dev.parent); 1747 return retval; 1748 } 1749 1750 /* Entry point for stopping the interface */ 1751 static int smsc911x_stop(struct net_device *dev) 1752 { 1753 struct smsc911x_data *pdata = netdev_priv(dev); 1754 unsigned int temp; 1755 1756 /* Disable all device interrupts */ 1757 temp = smsc911x_reg_read(pdata, INT_CFG); 1758 temp &= ~INT_CFG_IRQ_EN_; 1759 smsc911x_reg_write(pdata, INT_CFG, temp); 1760 1761 /* Stop Tx and Rx polling */ 1762 netif_stop_queue(dev); 1763 napi_disable(&pdata->napi); 1764 1765 /* At this point all Rx and Tx activity is stopped */ 1766 dev->stats.rx_dropped += smsc911x_reg_read(pdata, RX_DROP); 1767 smsc911x_tx_update_txcounters(dev); 1768 1769 free_irq(dev->irq, dev); 1770 1771 /* Bring the PHY down */ 1772 if (dev->phydev) { 1773 phy_stop(dev->phydev); 1774 phy_disconnect(dev->phydev); 1775 dev->phydev = NULL; 1776 } 1777 netif_carrier_off(dev); 1778 pm_runtime_put(dev->dev.parent); 1779 1780 SMSC_TRACE(pdata, ifdown, "Interface stopped"); 1781 return 0; 1782 } 1783 1784 /* Entry point for transmitting a packet */ 1785 static netdev_tx_t 1786 smsc911x_hard_start_xmit(struct sk_buff *skb, struct net_device *dev) 1787 { 1788 struct smsc911x_data *pdata = netdev_priv(dev); 1789 unsigned int freespace; 1790 unsigned int tx_cmd_a; 1791 unsigned int tx_cmd_b; 1792 unsigned int temp; 1793 u32 wrsz; 1794 ulong bufp; 1795 1796 freespace = smsc911x_reg_read(pdata, TX_FIFO_INF) & TX_FIFO_INF_TDFREE_; 1797 1798 if (unlikely(freespace < TX_FIFO_LOW_THRESHOLD)) 1799 SMSC_WARN(pdata, tx_err, 1800 "Tx data fifo low, space available: %d", freespace); 1801 1802 /* Word alignment adjustment */ 1803 tx_cmd_a = (u32)((ulong)skb->data & 0x03) << 16; 1804 tx_cmd_a |= TX_CMD_A_FIRST_SEG_ | TX_CMD_A_LAST_SEG_; 1805 tx_cmd_a |= (unsigned int)skb->len; 1806 1807 tx_cmd_b = ((unsigned int)skb->len) << 16; 1808 tx_cmd_b |= (unsigned int)skb->len; 1809 1810 smsc911x_reg_write(pdata, TX_DATA_FIFO, tx_cmd_a); 1811 smsc911x_reg_write(pdata, TX_DATA_FIFO, tx_cmd_b); 1812 1813 bufp = (ulong)skb->data & (~0x3); 1814 wrsz = (u32)skb->len + 3; 1815 wrsz += (u32)((ulong)skb->data & 0x3); 1816 wrsz >>= 2; 1817 1818 pdata->ops->tx_writefifo(pdata, (unsigned int *)bufp, wrsz); 1819 freespace -= (skb->len + 32); 1820 skb_tx_timestamp(skb); 1821 dev_consume_skb_any(skb); 1822 1823 if (unlikely(smsc911x_tx_get_txstatcount(pdata) >= 30)) 1824 smsc911x_tx_update_txcounters(dev); 1825 1826 if (freespace < TX_FIFO_LOW_THRESHOLD) { 1827 netif_stop_queue(dev); 1828 temp = smsc911x_reg_read(pdata, FIFO_INT); 1829 temp &= 0x00FFFFFF; 1830 temp |= 0x32000000; 1831 smsc911x_reg_write(pdata, FIFO_INT, temp); 1832 } 1833 1834 return NETDEV_TX_OK; 1835 } 1836 1837 /* Entry point for getting status counters */ 1838 static struct net_device_stats *smsc911x_get_stats(struct net_device *dev) 1839 { 1840 struct smsc911x_data *pdata = netdev_priv(dev); 1841 smsc911x_tx_update_txcounters(dev); 1842 dev->stats.rx_dropped += smsc911x_reg_read(pdata, RX_DROP); 1843 return &dev->stats; 1844 } 1845 1846 /* Entry point for setting addressing modes */ 1847 static void smsc911x_set_multicast_list(struct net_device *dev) 1848 { 1849 struct smsc911x_data *pdata = netdev_priv(dev); 1850 unsigned long flags; 1851 1852 if (dev->flags & IFF_PROMISC) { 1853 /* Enabling promiscuous mode */ 1854 pdata->set_bits_mask = MAC_CR_PRMS_; 1855 pdata->clear_bits_mask = (MAC_CR_MCPAS_ | MAC_CR_HPFILT_); 1856 pdata->hashhi = 0; 1857 pdata->hashlo = 0; 1858 } else if (dev->flags & IFF_ALLMULTI) { 1859 /* Enabling all multicast mode */ 1860 pdata->set_bits_mask = MAC_CR_MCPAS_; 1861 pdata->clear_bits_mask = (MAC_CR_PRMS_ | MAC_CR_HPFILT_); 1862 pdata->hashhi = 0; 1863 pdata->hashlo = 0; 1864 } else if (!netdev_mc_empty(dev)) { 1865 /* Enabling specific multicast addresses */ 1866 unsigned int hash_high = 0; 1867 unsigned int hash_low = 0; 1868 struct netdev_hw_addr *ha; 1869 1870 pdata->set_bits_mask = MAC_CR_HPFILT_; 1871 pdata->clear_bits_mask = (MAC_CR_PRMS_ | MAC_CR_MCPAS_); 1872 1873 netdev_for_each_mc_addr(ha, dev) { 1874 unsigned int bitnum = smsc911x_hash(ha->addr); 1875 unsigned int mask = 0x01 << (bitnum & 0x1F); 1876 1877 if (bitnum & 0x20) 1878 hash_high |= mask; 1879 else 1880 hash_low |= mask; 1881 } 1882 1883 pdata->hashhi = hash_high; 1884 pdata->hashlo = hash_low; 1885 } else { 1886 /* Enabling local MAC address only */ 1887 pdata->set_bits_mask = 0; 1888 pdata->clear_bits_mask = 1889 (MAC_CR_PRMS_ | MAC_CR_MCPAS_ | MAC_CR_HPFILT_); 1890 pdata->hashhi = 0; 1891 pdata->hashlo = 0; 1892 } 1893 1894 spin_lock_irqsave(&pdata->mac_lock, flags); 1895 1896 if (pdata->generation <= 1) { 1897 /* Older hardware revision - cannot change these flags while 1898 * receiving data */ 1899 if (!pdata->multicast_update_pending) { 1900 unsigned int temp; 1901 SMSC_TRACE(pdata, hw, "scheduling mcast update"); 1902 pdata->multicast_update_pending = 1; 1903 1904 /* Request the hardware to stop, then perform the 1905 * update when we get an RX_STOP interrupt */ 1906 temp = smsc911x_mac_read(pdata, MAC_CR); 1907 temp &= ~(MAC_CR_RXEN_); 1908 smsc911x_mac_write(pdata, MAC_CR, temp); 1909 } else { 1910 /* There is another update pending, this should now 1911 * use the newer values */ 1912 } 1913 } else { 1914 /* Newer hardware revision - can write immediately */ 1915 smsc911x_rx_multicast_update(pdata); 1916 } 1917 1918 spin_unlock_irqrestore(&pdata->mac_lock, flags); 1919 } 1920 1921 #ifdef CONFIG_NET_POLL_CONTROLLER 1922 static void smsc911x_poll_controller(struct net_device *dev) 1923 { 1924 disable_irq(dev->irq); 1925 smsc911x_irqhandler(0, dev); 1926 enable_irq(dev->irq); 1927 } 1928 #endif /* CONFIG_NET_POLL_CONTROLLER */ 1929 1930 static int smsc911x_set_mac_address(struct net_device *dev, void *p) 1931 { 1932 struct smsc911x_data *pdata = netdev_priv(dev); 1933 struct sockaddr *addr = p; 1934 1935 /* On older hardware revisions we cannot change the mac address 1936 * registers while receiving data. Newer devices can safely change 1937 * this at any time. */ 1938 if (pdata->generation <= 1 && netif_running(dev)) 1939 return -EBUSY; 1940 1941 if (!is_valid_ether_addr(addr->sa_data)) 1942 return -EADDRNOTAVAIL; 1943 1944 eth_hw_addr_set(dev, addr->sa_data); 1945 1946 spin_lock_irq(&pdata->mac_lock); 1947 smsc911x_set_hw_mac_address(pdata, dev->dev_addr); 1948 spin_unlock_irq(&pdata->mac_lock); 1949 1950 netdev_info(dev, "MAC Address: %pM\n", dev->dev_addr); 1951 1952 return 0; 1953 } 1954 1955 static void smsc911x_ethtool_getdrvinfo(struct net_device *dev, 1956 struct ethtool_drvinfo *info) 1957 { 1958 strscpy(info->driver, SMSC_CHIPNAME, sizeof(info->driver)); 1959 strscpy(info->version, SMSC_DRV_VERSION, sizeof(info->version)); 1960 strscpy(info->bus_info, dev_name(dev->dev.parent), 1961 sizeof(info->bus_info)); 1962 } 1963 1964 static u32 smsc911x_ethtool_getmsglevel(struct net_device *dev) 1965 { 1966 struct smsc911x_data *pdata = netdev_priv(dev); 1967 return pdata->msg_enable; 1968 } 1969 1970 static void smsc911x_ethtool_setmsglevel(struct net_device *dev, u32 level) 1971 { 1972 struct smsc911x_data *pdata = netdev_priv(dev); 1973 pdata->msg_enable = level; 1974 } 1975 1976 static int smsc911x_ethtool_getregslen(struct net_device *dev) 1977 { 1978 return (((E2P_DATA - ID_REV) / 4 + 1) + (WUCSR - MAC_CR) + 1 + 32) * 1979 sizeof(u32); 1980 } 1981 1982 static void 1983 smsc911x_ethtool_getregs(struct net_device *dev, struct ethtool_regs *regs, 1984 void *buf) 1985 { 1986 struct smsc911x_data *pdata = netdev_priv(dev); 1987 struct phy_device *phy_dev = dev->phydev; 1988 unsigned long flags; 1989 unsigned int i; 1990 unsigned int j = 0; 1991 u32 *data = buf; 1992 1993 regs->version = pdata->idrev; 1994 for (i = ID_REV; i <= E2P_DATA; i += (sizeof(u32))) 1995 data[j++] = smsc911x_reg_read(pdata, i); 1996 1997 for (i = MAC_CR; i <= WUCSR; i++) { 1998 spin_lock_irqsave(&pdata->mac_lock, flags); 1999 data[j++] = smsc911x_mac_read(pdata, i); 2000 spin_unlock_irqrestore(&pdata->mac_lock, flags); 2001 } 2002 2003 for (i = 0; i <= 31; i++) 2004 data[j++] = smsc911x_mii_read(phy_dev->mdio.bus, 2005 phy_dev->mdio.addr, i); 2006 } 2007 2008 static void smsc911x_eeprom_enable_access(struct smsc911x_data *pdata) 2009 { 2010 unsigned int temp = smsc911x_reg_read(pdata, GPIO_CFG); 2011 temp &= ~GPIO_CFG_EEPR_EN_; 2012 smsc911x_reg_write(pdata, GPIO_CFG, temp); 2013 msleep(1); 2014 } 2015 2016 static int smsc911x_eeprom_send_cmd(struct smsc911x_data *pdata, u32 op) 2017 { 2018 int timeout = 100; 2019 u32 e2cmd; 2020 2021 SMSC_TRACE(pdata, drv, "op 0x%08x", op); 2022 if (smsc911x_reg_read(pdata, E2P_CMD) & E2P_CMD_EPC_BUSY_) { 2023 SMSC_WARN(pdata, drv, "Busy at start"); 2024 return -EBUSY; 2025 } 2026 2027 e2cmd = op | E2P_CMD_EPC_BUSY_; 2028 smsc911x_reg_write(pdata, E2P_CMD, e2cmd); 2029 2030 do { 2031 msleep(1); 2032 e2cmd = smsc911x_reg_read(pdata, E2P_CMD); 2033 } while ((e2cmd & E2P_CMD_EPC_BUSY_) && (--timeout)); 2034 2035 if (!timeout) { 2036 SMSC_TRACE(pdata, drv, "TIMED OUT"); 2037 return -EAGAIN; 2038 } 2039 2040 if (e2cmd & E2P_CMD_EPC_TIMEOUT_) { 2041 SMSC_TRACE(pdata, drv, "Error occurred during eeprom operation"); 2042 return -EINVAL; 2043 } 2044 2045 return 0; 2046 } 2047 2048 static int smsc911x_eeprom_read_location(struct smsc911x_data *pdata, 2049 u8 address, u8 *data) 2050 { 2051 u32 op = E2P_CMD_EPC_CMD_READ_ | address; 2052 int ret; 2053 2054 SMSC_TRACE(pdata, drv, "address 0x%x", address); 2055 ret = smsc911x_eeprom_send_cmd(pdata, op); 2056 2057 if (!ret) 2058 data[address] = smsc911x_reg_read(pdata, E2P_DATA); 2059 2060 return ret; 2061 } 2062 2063 static int smsc911x_eeprom_write_location(struct smsc911x_data *pdata, 2064 u8 address, u8 data) 2065 { 2066 u32 op = E2P_CMD_EPC_CMD_ERASE_ | address; 2067 int ret; 2068 2069 SMSC_TRACE(pdata, drv, "address 0x%x, data 0x%x", address, data); 2070 ret = smsc911x_eeprom_send_cmd(pdata, op); 2071 2072 if (!ret) { 2073 op = E2P_CMD_EPC_CMD_WRITE_ | address; 2074 smsc911x_reg_write(pdata, E2P_DATA, (u32)data); 2075 2076 /* Workaround for hardware read-after-write restriction */ 2077 smsc911x_reg_read(pdata, BYTE_TEST); 2078 2079 ret = smsc911x_eeprom_send_cmd(pdata, op); 2080 } 2081 2082 return ret; 2083 } 2084 2085 static int smsc911x_ethtool_get_eeprom_len(struct net_device *dev) 2086 { 2087 return SMSC911X_EEPROM_SIZE; 2088 } 2089 2090 static int smsc911x_ethtool_get_eeprom(struct net_device *dev, 2091 struct ethtool_eeprom *eeprom, u8 *data) 2092 { 2093 struct smsc911x_data *pdata = netdev_priv(dev); 2094 u8 eeprom_data[SMSC911X_EEPROM_SIZE]; 2095 int len; 2096 int i; 2097 2098 smsc911x_eeprom_enable_access(pdata); 2099 2100 len = min(eeprom->len, SMSC911X_EEPROM_SIZE); 2101 for (i = 0; i < len; i++) { 2102 int ret = smsc911x_eeprom_read_location(pdata, i, eeprom_data); 2103 if (ret < 0) { 2104 eeprom->len = 0; 2105 return ret; 2106 } 2107 } 2108 2109 memcpy(data, &eeprom_data[eeprom->offset], len); 2110 eeprom->len = len; 2111 return 0; 2112 } 2113 2114 static int smsc911x_ethtool_set_eeprom(struct net_device *dev, 2115 struct ethtool_eeprom *eeprom, u8 *data) 2116 { 2117 int ret; 2118 struct smsc911x_data *pdata = netdev_priv(dev); 2119 2120 smsc911x_eeprom_enable_access(pdata); 2121 smsc911x_eeprom_send_cmd(pdata, E2P_CMD_EPC_CMD_EWEN_); 2122 ret = smsc911x_eeprom_write_location(pdata, eeprom->offset, *data); 2123 smsc911x_eeprom_send_cmd(pdata, E2P_CMD_EPC_CMD_EWDS_); 2124 2125 /* Single byte write, according to man page */ 2126 eeprom->len = 1; 2127 2128 return ret; 2129 } 2130 2131 static const struct ethtool_ops smsc911x_ethtool_ops = { 2132 .get_link = ethtool_op_get_link, 2133 .get_drvinfo = smsc911x_ethtool_getdrvinfo, 2134 .nway_reset = phy_ethtool_nway_reset, 2135 .get_msglevel = smsc911x_ethtool_getmsglevel, 2136 .set_msglevel = smsc911x_ethtool_setmsglevel, 2137 .get_regs_len = smsc911x_ethtool_getregslen, 2138 .get_regs = smsc911x_ethtool_getregs, 2139 .get_eeprom_len = smsc911x_ethtool_get_eeprom_len, 2140 .get_eeprom = smsc911x_ethtool_get_eeprom, 2141 .set_eeprom = smsc911x_ethtool_set_eeprom, 2142 .get_ts_info = ethtool_op_get_ts_info, 2143 .get_link_ksettings = phy_ethtool_get_link_ksettings, 2144 .set_link_ksettings = phy_ethtool_set_link_ksettings, 2145 }; 2146 2147 static const struct net_device_ops smsc911x_netdev_ops = { 2148 .ndo_open = smsc911x_open, 2149 .ndo_stop = smsc911x_stop, 2150 .ndo_start_xmit = smsc911x_hard_start_xmit, 2151 .ndo_get_stats = smsc911x_get_stats, 2152 .ndo_set_rx_mode = smsc911x_set_multicast_list, 2153 .ndo_eth_ioctl = phy_do_ioctl_running, 2154 .ndo_validate_addr = eth_validate_addr, 2155 .ndo_set_mac_address = smsc911x_set_mac_address, 2156 #ifdef CONFIG_NET_POLL_CONTROLLER 2157 .ndo_poll_controller = smsc911x_poll_controller, 2158 #endif 2159 }; 2160 2161 /* copies the current mac address from hardware to dev->dev_addr */ 2162 static void smsc911x_read_mac_address(struct net_device *dev) 2163 { 2164 struct smsc911x_data *pdata = netdev_priv(dev); 2165 u32 mac_high16 = smsc911x_mac_read(pdata, ADDRH); 2166 u32 mac_low32 = smsc911x_mac_read(pdata, ADDRL); 2167 u8 addr[ETH_ALEN]; 2168 2169 addr[0] = (u8)(mac_low32); 2170 addr[1] = (u8)(mac_low32 >> 8); 2171 addr[2] = (u8)(mac_low32 >> 16); 2172 addr[3] = (u8)(mac_low32 >> 24); 2173 addr[4] = (u8)(mac_high16); 2174 addr[5] = (u8)(mac_high16 >> 8); 2175 eth_hw_addr_set(dev, addr); 2176 } 2177 2178 /* Initializing private device structures, only called from probe */ 2179 static int smsc911x_init(struct net_device *dev) 2180 { 2181 struct smsc911x_data *pdata = netdev_priv(dev); 2182 unsigned int byte_test, mask; 2183 unsigned int to = 100; 2184 2185 SMSC_TRACE(pdata, probe, "Driver Parameters:"); 2186 SMSC_TRACE(pdata, probe, "LAN base: 0x%08lX", 2187 (unsigned long)pdata->ioaddr); 2188 SMSC_TRACE(pdata, probe, "IRQ: %d", dev->irq); 2189 SMSC_TRACE(pdata, probe, "PHY will be autodetected."); 2190 2191 spin_lock_init(&pdata->dev_lock); 2192 spin_lock_init(&pdata->mac_lock); 2193 2194 if (pdata->ioaddr == NULL) { 2195 SMSC_WARN(pdata, probe, "pdata->ioaddr: 0x00000000"); 2196 return -ENODEV; 2197 } 2198 2199 /* 2200 * poll the READY bit in PMT_CTRL. Any other access to the device is 2201 * forbidden while this bit isn't set. Try for 100ms 2202 * 2203 * Note that this test is done before the WORD_SWAP register is 2204 * programmed. So in some configurations the READY bit is at 16 before 2205 * WORD_SWAP is written to. This issue is worked around by waiting 2206 * until either bit 0 or bit 16 gets set in PMT_CTRL. 2207 * 2208 * SMSC has confirmed that checking bit 16 (marked as reserved in 2209 * the datasheet) is fine since these bits "will either never be set 2210 * or can only go high after READY does (so also indicate the device 2211 * is ready)". 2212 */ 2213 2214 mask = PMT_CTRL_READY_ | swahw32(PMT_CTRL_READY_); 2215 while (!(smsc911x_reg_read(pdata, PMT_CTRL) & mask) && --to) 2216 udelay(1000); 2217 2218 if (to == 0) { 2219 netdev_err(dev, "Device not READY in 100ms aborting\n"); 2220 return -ENODEV; 2221 } 2222 2223 /* Check byte ordering */ 2224 byte_test = smsc911x_reg_read(pdata, BYTE_TEST); 2225 SMSC_TRACE(pdata, probe, "BYTE_TEST: 0x%08X", byte_test); 2226 if (byte_test == 0x43218765) { 2227 SMSC_TRACE(pdata, probe, "BYTE_TEST looks swapped, " 2228 "applying WORD_SWAP"); 2229 smsc911x_reg_write(pdata, WORD_SWAP, 0xffffffff); 2230 2231 /* 1 dummy read of BYTE_TEST is needed after a write to 2232 * WORD_SWAP before its contents are valid */ 2233 byte_test = smsc911x_reg_read(pdata, BYTE_TEST); 2234 2235 byte_test = smsc911x_reg_read(pdata, BYTE_TEST); 2236 } 2237 2238 if (byte_test != 0x87654321) { 2239 SMSC_WARN(pdata, drv, "BYTE_TEST: 0x%08X", byte_test); 2240 if (((byte_test >> 16) & 0xFFFF) == (byte_test & 0xFFFF)) { 2241 SMSC_WARN(pdata, probe, 2242 "top 16 bits equal to bottom 16 bits"); 2243 SMSC_TRACE(pdata, probe, 2244 "This may mean the chip is set " 2245 "for 32 bit while the bus is reading 16 bit"); 2246 } 2247 return -ENODEV; 2248 } 2249 2250 /* Default generation to zero (all workarounds apply) */ 2251 pdata->generation = 0; 2252 2253 pdata->idrev = smsc911x_reg_read(pdata, ID_REV); 2254 switch (pdata->idrev & 0xFFFF0000) { 2255 case LAN9118: 2256 case LAN9117: 2257 case LAN9116: 2258 case LAN9115: 2259 case LAN89218: 2260 /* LAN911[5678] family */ 2261 pdata->generation = pdata->idrev & 0x0000FFFF; 2262 break; 2263 2264 case LAN9218: 2265 case LAN9217: 2266 case LAN9216: 2267 case LAN9215: 2268 /* LAN921[5678] family */ 2269 pdata->generation = 3; 2270 break; 2271 2272 case LAN9210: 2273 case LAN9211: 2274 case LAN9220: 2275 case LAN9221: 2276 case LAN9250: 2277 /* LAN9210/LAN9211/LAN9220/LAN9221/LAN9250 */ 2278 pdata->generation = 4; 2279 break; 2280 2281 default: 2282 SMSC_WARN(pdata, probe, "LAN911x not identified, idrev: 0x%08X", 2283 pdata->idrev); 2284 return -ENODEV; 2285 } 2286 2287 SMSC_TRACE(pdata, probe, 2288 "LAN911x identified, idrev: 0x%08X, generation: %d", 2289 pdata->idrev, pdata->generation); 2290 2291 if (pdata->generation == 0) 2292 SMSC_WARN(pdata, probe, 2293 "This driver is not intended for this chip revision"); 2294 2295 /* workaround for platforms without an eeprom, where the mac address 2296 * is stored elsewhere and set by the bootloader. This saves the 2297 * mac address before resetting the device */ 2298 if (pdata->config.flags & SMSC911X_SAVE_MAC_ADDRESS) { 2299 spin_lock_irq(&pdata->mac_lock); 2300 smsc911x_read_mac_address(dev); 2301 spin_unlock_irq(&pdata->mac_lock); 2302 } 2303 2304 /* Reset the LAN911x */ 2305 if (smsc911x_phy_reset(pdata) || smsc911x_soft_reset(pdata)) 2306 return -ENODEV; 2307 2308 dev->flags |= IFF_MULTICAST; 2309 netif_napi_add_weight(dev, &pdata->napi, smsc911x_poll, 2310 SMSC_NAPI_WEIGHT); 2311 dev->netdev_ops = &smsc911x_netdev_ops; 2312 dev->ethtool_ops = &smsc911x_ethtool_ops; 2313 2314 return 0; 2315 } 2316 2317 static int smsc911x_drv_remove(struct platform_device *pdev) 2318 { 2319 struct net_device *dev; 2320 struct smsc911x_data *pdata; 2321 struct resource *res; 2322 2323 dev = platform_get_drvdata(pdev); 2324 BUG_ON(!dev); 2325 pdata = netdev_priv(dev); 2326 BUG_ON(!pdata); 2327 BUG_ON(!pdata->ioaddr); 2328 2329 SMSC_TRACE(pdata, ifdown, "Stopping driver"); 2330 2331 unregister_netdev(dev); 2332 2333 mdiobus_unregister(pdata->mii_bus); 2334 mdiobus_free(pdata->mii_bus); 2335 2336 res = platform_get_resource_byname(pdev, IORESOURCE_MEM, 2337 "smsc911x-memory"); 2338 if (!res) 2339 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 2340 2341 release_mem_region(res->start, resource_size(res)); 2342 2343 iounmap(pdata->ioaddr); 2344 2345 (void)smsc911x_disable_resources(pdev); 2346 smsc911x_free_resources(pdev); 2347 2348 free_netdev(dev); 2349 2350 pm_runtime_disable(&pdev->dev); 2351 2352 return 0; 2353 } 2354 2355 /* standard register acces */ 2356 static const struct smsc911x_ops standard_smsc911x_ops = { 2357 .reg_read = __smsc911x_reg_read, 2358 .reg_write = __smsc911x_reg_write, 2359 .rx_readfifo = smsc911x_rx_readfifo, 2360 .tx_writefifo = smsc911x_tx_writefifo, 2361 }; 2362 2363 /* shifted register access */ 2364 static const struct smsc911x_ops shifted_smsc911x_ops = { 2365 .reg_read = __smsc911x_reg_read_shift, 2366 .reg_write = __smsc911x_reg_write_shift, 2367 .rx_readfifo = smsc911x_rx_readfifo_shift, 2368 .tx_writefifo = smsc911x_tx_writefifo_shift, 2369 }; 2370 2371 static int smsc911x_probe_config(struct smsc911x_platform_config *config, 2372 struct device *dev) 2373 { 2374 int phy_interface; 2375 u32 width = 0; 2376 int err; 2377 2378 phy_interface = device_get_phy_mode(dev); 2379 if (phy_interface < 0) 2380 phy_interface = PHY_INTERFACE_MODE_NA; 2381 config->phy_interface = phy_interface; 2382 2383 device_get_mac_address(dev, config->mac); 2384 2385 err = device_property_read_u32(dev, "reg-io-width", &width); 2386 if (err == -ENXIO) 2387 return err; 2388 if (!err && width == 4) 2389 config->flags |= SMSC911X_USE_32BIT; 2390 else 2391 config->flags |= SMSC911X_USE_16BIT; 2392 2393 device_property_read_u32(dev, "reg-shift", &config->shift); 2394 2395 if (device_property_present(dev, "smsc,irq-active-high")) 2396 config->irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_HIGH; 2397 2398 if (device_property_present(dev, "smsc,irq-push-pull")) 2399 config->irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL; 2400 2401 if (device_property_present(dev, "smsc,force-internal-phy")) 2402 config->flags |= SMSC911X_FORCE_INTERNAL_PHY; 2403 2404 if (device_property_present(dev, "smsc,force-external-phy")) 2405 config->flags |= SMSC911X_FORCE_EXTERNAL_PHY; 2406 2407 if (device_property_present(dev, "smsc,save-mac-address")) 2408 config->flags |= SMSC911X_SAVE_MAC_ADDRESS; 2409 2410 return 0; 2411 } 2412 2413 static int smsc911x_drv_probe(struct platform_device *pdev) 2414 { 2415 struct net_device *dev; 2416 struct smsc911x_data *pdata; 2417 struct smsc911x_platform_config *config = dev_get_platdata(&pdev->dev); 2418 struct resource *res; 2419 int res_size, irq; 2420 int retval; 2421 2422 res = platform_get_resource_byname(pdev, IORESOURCE_MEM, 2423 "smsc911x-memory"); 2424 if (!res) 2425 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 2426 if (!res) { 2427 pr_warn("Could not allocate resource\n"); 2428 retval = -ENODEV; 2429 goto out_0; 2430 } 2431 res_size = resource_size(res); 2432 2433 irq = platform_get_irq(pdev, 0); 2434 if (irq == -EPROBE_DEFER) { 2435 retval = -EPROBE_DEFER; 2436 goto out_0; 2437 } else if (irq < 0) { 2438 pr_warn("Could not allocate irq resource\n"); 2439 retval = -ENODEV; 2440 goto out_0; 2441 } 2442 2443 if (!request_mem_region(res->start, res_size, SMSC_CHIPNAME)) { 2444 retval = -EBUSY; 2445 goto out_0; 2446 } 2447 2448 dev = alloc_etherdev(sizeof(struct smsc911x_data)); 2449 if (!dev) { 2450 retval = -ENOMEM; 2451 goto out_release_io_1; 2452 } 2453 2454 SET_NETDEV_DEV(dev, &pdev->dev); 2455 2456 pdata = netdev_priv(dev); 2457 dev->irq = irq; 2458 pdata->ioaddr = ioremap(res->start, res_size); 2459 if (!pdata->ioaddr) { 2460 retval = -ENOMEM; 2461 goto out_ioremap_fail; 2462 } 2463 2464 pdata->dev = dev; 2465 pdata->msg_enable = ((1 << debug) - 1); 2466 2467 platform_set_drvdata(pdev, dev); 2468 2469 retval = smsc911x_request_resources(pdev); 2470 if (retval) 2471 goto out_request_resources_fail; 2472 2473 retval = smsc911x_enable_resources(pdev); 2474 if (retval) 2475 goto out_enable_resources_fail; 2476 2477 if (pdata->ioaddr == NULL) { 2478 SMSC_WARN(pdata, probe, "Error smsc911x base address invalid"); 2479 retval = -ENOMEM; 2480 goto out_disable_resources; 2481 } 2482 2483 retval = smsc911x_probe_config(&pdata->config, &pdev->dev); 2484 if (retval && config) { 2485 /* copy config parameters across to pdata */ 2486 memcpy(&pdata->config, config, sizeof(pdata->config)); 2487 retval = 0; 2488 } 2489 2490 if (retval) { 2491 SMSC_WARN(pdata, probe, "Error smsc911x config not found"); 2492 goto out_disable_resources; 2493 } 2494 2495 /* assume standard, non-shifted, access to HW registers */ 2496 pdata->ops = &standard_smsc911x_ops; 2497 /* apply the right access if shifting is needed */ 2498 if (pdata->config.shift) 2499 pdata->ops = &shifted_smsc911x_ops; 2500 2501 pm_runtime_enable(&pdev->dev); 2502 pm_runtime_get_sync(&pdev->dev); 2503 2504 retval = smsc911x_init(dev); 2505 if (retval < 0) 2506 goto out_init_fail; 2507 2508 netif_carrier_off(dev); 2509 2510 retval = smsc911x_mii_init(pdev, dev); 2511 if (retval) { 2512 SMSC_WARN(pdata, probe, "Error %i initialising mii", retval); 2513 goto out_init_fail; 2514 } 2515 2516 retval = register_netdev(dev); 2517 if (retval) { 2518 SMSC_WARN(pdata, probe, "Error %i registering device", retval); 2519 goto out_init_fail; 2520 } else { 2521 SMSC_TRACE(pdata, probe, 2522 "Network interface: \"%s\"", dev->name); 2523 } 2524 2525 spin_lock_irq(&pdata->mac_lock); 2526 2527 /* Check if mac address has been specified when bringing interface up */ 2528 if (is_valid_ether_addr(dev->dev_addr)) { 2529 smsc911x_set_hw_mac_address(pdata, dev->dev_addr); 2530 SMSC_TRACE(pdata, probe, 2531 "MAC Address is specified by configuration"); 2532 } else if (is_valid_ether_addr(pdata->config.mac)) { 2533 eth_hw_addr_set(dev, pdata->config.mac); 2534 SMSC_TRACE(pdata, probe, 2535 "MAC Address specified by platform data"); 2536 } else { 2537 /* Try reading mac address from device. if EEPROM is present 2538 * it will already have been set */ 2539 smsc_get_mac(dev); 2540 2541 if (is_valid_ether_addr(dev->dev_addr)) { 2542 /* eeprom values are valid so use them */ 2543 SMSC_TRACE(pdata, probe, 2544 "Mac Address is read from LAN911x EEPROM"); 2545 } else { 2546 /* eeprom values are invalid, generate random MAC */ 2547 eth_hw_addr_random(dev); 2548 smsc911x_set_hw_mac_address(pdata, dev->dev_addr); 2549 SMSC_TRACE(pdata, probe, 2550 "MAC Address is set to eth_random_addr"); 2551 } 2552 } 2553 2554 spin_unlock_irq(&pdata->mac_lock); 2555 pm_runtime_put(&pdev->dev); 2556 2557 netdev_info(dev, "MAC Address: %pM\n", dev->dev_addr); 2558 2559 return 0; 2560 2561 out_init_fail: 2562 pm_runtime_put(&pdev->dev); 2563 pm_runtime_disable(&pdev->dev); 2564 out_disable_resources: 2565 (void)smsc911x_disable_resources(pdev); 2566 out_enable_resources_fail: 2567 smsc911x_free_resources(pdev); 2568 out_request_resources_fail: 2569 iounmap(pdata->ioaddr); 2570 out_ioremap_fail: 2571 free_netdev(dev); 2572 out_release_io_1: 2573 release_mem_region(res->start, resource_size(res)); 2574 out_0: 2575 return retval; 2576 } 2577 2578 #ifdef CONFIG_PM 2579 /* This implementation assumes the devices remains powered on its VDDVARIO 2580 * pins during suspend. */ 2581 2582 /* TODO: implement freeze/thaw callbacks for hibernation.*/ 2583 2584 static int smsc911x_suspend(struct device *dev) 2585 { 2586 struct net_device *ndev = dev_get_drvdata(dev); 2587 struct smsc911x_data *pdata = netdev_priv(ndev); 2588 2589 if (netif_running(ndev)) { 2590 netif_stop_queue(ndev); 2591 netif_device_detach(ndev); 2592 if (!device_may_wakeup(dev)) 2593 phy_stop(ndev->phydev); 2594 } 2595 2596 /* enable wake on LAN, energy detection and the external PME 2597 * signal. */ 2598 smsc911x_reg_write(pdata, PMT_CTRL, 2599 PMT_CTRL_PM_MODE_D1_ | PMT_CTRL_WOL_EN_ | 2600 PMT_CTRL_ED_EN_ | PMT_CTRL_PME_EN_); 2601 2602 pm_runtime_disable(dev); 2603 pm_runtime_set_suspended(dev); 2604 2605 return 0; 2606 } 2607 2608 static int smsc911x_resume(struct device *dev) 2609 { 2610 struct net_device *ndev = dev_get_drvdata(dev); 2611 struct smsc911x_data *pdata = netdev_priv(ndev); 2612 unsigned int to = 100; 2613 2614 pm_runtime_enable(dev); 2615 pm_runtime_resume(dev); 2616 2617 /* Note 3.11 from the datasheet: 2618 * "When the LAN9220 is in a power saving state, a write of any 2619 * data to the BYTE_TEST register will wake-up the device." 2620 */ 2621 smsc911x_reg_write(pdata, BYTE_TEST, 0); 2622 2623 /* poll the READY bit in PMT_CTRL. Any other access to the device is 2624 * forbidden while this bit isn't set. Try for 100ms and return -EIO 2625 * if it failed. */ 2626 while (!(smsc911x_reg_read(pdata, PMT_CTRL) & PMT_CTRL_READY_) && --to) 2627 udelay(1000); 2628 2629 if (to == 0) 2630 return -EIO; 2631 2632 if (netif_running(ndev)) { 2633 netif_device_attach(ndev); 2634 netif_start_queue(ndev); 2635 if (!device_may_wakeup(dev)) 2636 phy_start(ndev->phydev); 2637 } 2638 2639 return 0; 2640 } 2641 2642 static const struct dev_pm_ops smsc911x_pm_ops = { 2643 .suspend = smsc911x_suspend, 2644 .resume = smsc911x_resume, 2645 }; 2646 2647 #define SMSC911X_PM_OPS (&smsc911x_pm_ops) 2648 2649 #else 2650 #define SMSC911X_PM_OPS NULL 2651 #endif 2652 2653 #ifdef CONFIG_OF 2654 static const struct of_device_id smsc911x_dt_ids[] = { 2655 { .compatible = "smsc,lan9115", }, 2656 { /* sentinel */ } 2657 }; 2658 MODULE_DEVICE_TABLE(of, smsc911x_dt_ids); 2659 #endif 2660 2661 #ifdef CONFIG_ACPI 2662 static const struct acpi_device_id smsc911x_acpi_match[] = { 2663 { "ARMH9118", 0 }, 2664 { } 2665 }; 2666 MODULE_DEVICE_TABLE(acpi, smsc911x_acpi_match); 2667 #endif 2668 2669 static struct platform_driver smsc911x_driver = { 2670 .probe = smsc911x_drv_probe, 2671 .remove = smsc911x_drv_remove, 2672 .driver = { 2673 .name = SMSC_CHIPNAME, 2674 .pm = SMSC911X_PM_OPS, 2675 .of_match_table = of_match_ptr(smsc911x_dt_ids), 2676 .acpi_match_table = ACPI_PTR(smsc911x_acpi_match), 2677 }, 2678 }; 2679 2680 /* Entry point for loading the module */ 2681 static int __init smsc911x_init_module(void) 2682 { 2683 SMSC_INITIALIZE(); 2684 return platform_driver_register(&smsc911x_driver); 2685 } 2686 2687 /* entry point for unloading the module */ 2688 static void __exit smsc911x_cleanup_module(void) 2689 { 2690 platform_driver_unregister(&smsc911x_driver); 2691 } 2692 2693 module_init(smsc911x_init_module); 2694 module_exit(smsc911x_cleanup_module); 2695