1 /* 2 * sgiseeq.h: Defines for the Seeq8003 ethernet controller. 3 * 4 * Copyright (C) 1996 David S. Miller (davem@davemloft.net) 5 */ 6 #ifndef _SGISEEQ_H 7 #define _SGISEEQ_H 8 9 struct sgiseeq_wregs { 10 volatile unsigned int multicase_high[2]; 11 volatile unsigned int frame_gap; 12 volatile unsigned int control; 13 }; 14 15 struct sgiseeq_rregs { 16 volatile unsigned int collision_tx[2]; 17 volatile unsigned int collision_all[2]; 18 volatile unsigned int _unused0; 19 volatile unsigned int rflags; 20 }; 21 22 struct sgiseeq_regs { 23 union { 24 volatile unsigned int eth_addr[6]; 25 volatile unsigned int multicast_low[6]; 26 struct sgiseeq_wregs wregs; 27 struct sgiseeq_rregs rregs; 28 } rw; 29 volatile unsigned int rstat; 30 volatile unsigned int tstat; 31 }; 32 33 /* Seeq8003 receive status register */ 34 #define SEEQ_RSTAT_OVERF 0x001 /* Overflow */ 35 #define SEEQ_RSTAT_CERROR 0x002 /* CRC error */ 36 #define SEEQ_RSTAT_DERROR 0x004 /* Dribble error */ 37 #define SEEQ_RSTAT_SFRAME 0x008 /* Short frame */ 38 #define SEEQ_RSTAT_REOF 0x010 /* Received end of frame */ 39 #define SEEQ_RSTAT_FIG 0x020 /* Frame is good */ 40 #define SEEQ_RSTAT_TIMEO 0x040 /* Timeout, or late receive */ 41 #define SEEQ_RSTAT_WHICH 0x080 /* Which status, 1=old 0=new */ 42 #define SEEQ_RSTAT_LITTLE 0x100 /* DMA is done in little endian format */ 43 #define SEEQ_RSTAT_SDMA 0x200 /* DMA has started */ 44 #define SEEQ_RSTAT_ADMA 0x400 /* DMA is active */ 45 #define SEEQ_RSTAT_ROVERF 0x800 /* Receive buffer overflow */ 46 47 /* Seeq8003 receive command register */ 48 #define SEEQ_RCMD_RDISAB 0x000 /* Disable receiver on the Seeq8003 */ 49 #define SEEQ_RCMD_IOVERF 0x001 /* IRQ on buffer overflows */ 50 #define SEEQ_RCMD_ICRC 0x002 /* IRQ on CRC errors */ 51 #define SEEQ_RCMD_IDRIB 0x004 /* IRQ on dribble errors */ 52 #define SEEQ_RCMD_ISHORT 0x008 /* IRQ on short frames */ 53 #define SEEQ_RCMD_IEOF 0x010 /* IRQ on end of frame */ 54 #define SEEQ_RCMD_IGOOD 0x020 /* IRQ on good frames */ 55 #define SEEQ_RCMD_RANY 0x040 /* Receive any frame */ 56 #define SEEQ_RCMD_RBCAST 0x080 /* Receive broadcasts */ 57 #define SEEQ_RCMD_RBMCAST 0x0c0 /* Receive broadcasts/multicasts */ 58 59 /* Seeq8003 transmit status register */ 60 #define SEEQ_TSTAT_UFLOW 0x001 /* Transmit buffer underflow */ 61 #define SEEQ_TSTAT_CLS 0x002 /* Collision detected */ 62 #define SEEQ_TSTAT_R16 0x004 /* Did 16 retries to tx a frame */ 63 #define SEEQ_TSTAT_PTRANS 0x008 /* Packet was transmitted ok */ 64 #define SEEQ_TSTAT_LCLS 0x010 /* Late collision occurred */ 65 #define SEEQ_TSTAT_WHICH 0x080 /* Which status, 1=old 0=new */ 66 #define SEEQ_TSTAT_TLE 0x100 /* DMA is done in little endian format */ 67 #define SEEQ_TSTAT_SDMA 0x200 /* DMA has started */ 68 #define SEEQ_TSTAT_ADMA 0x400 /* DMA is active */ 69 70 /* Seeq8003 transmit command register */ 71 #define SEEQ_TCMD_RB0 0x00 /* Register bank zero w/station addr */ 72 #define SEEQ_TCMD_IUF 0x01 /* IRQ on tx underflow */ 73 #define SEEQ_TCMD_IC 0x02 /* IRQ on collisions */ 74 #define SEEQ_TCMD_I16 0x04 /* IRQ after 16 failed attempts to tx frame */ 75 #define SEEQ_TCMD_IPT 0x08 /* IRQ when packet successfully transmitted */ 76 #define SEEQ_TCMD_RB1 0x20 /* Register bank one w/multi-cast low byte */ 77 #define SEEQ_TCMD_RB2 0x40 /* Register bank two w/multi-cast high byte */ 78 79 /* Seeq8003 control register */ 80 #define SEEQ_CTRL_XCNT 0x01 81 #define SEEQ_CTRL_ACCNT 0x02 82 #define SEEQ_CTRL_SFLAG 0x04 83 #define SEEQ_CTRL_EMULTI 0x08 84 #define SEEQ_CTRL_ESHORT 0x10 85 #define SEEQ_CTRL_ENCARR 0x20 86 87 /* Seeq8003 control registers on the SGI Hollywood HPC. */ 88 #define SEEQ_HPIO_P1BITS 0x00000001 /* cycles to stay in P1 phase for PIO */ 89 #define SEEQ_HPIO_P2BITS 0x00000060 /* cycles to stay in P2 phase for PIO */ 90 #define SEEQ_HPIO_P3BITS 0x00000100 /* cycles to stay in P3 phase for PIO */ 91 #define SEEQ_HDMA_D1BITS 0x00000006 /* cycles to stay in D1 phase for DMA */ 92 #define SEEQ_HDMA_D2BITS 0x00000020 /* cycles to stay in D2 phase for DMA */ 93 #define SEEQ_HDMA_D3BITS 0x00000000 /* cycles to stay in D3 phase for DMA */ 94 #define SEEQ_HDMA_TIMEO 0x00030000 /* cycles for DMA timeout */ 95 #define SEEQ_HCTL_NORM 0x00000000 /* Normal operation mode */ 96 #define SEEQ_HCTL_RESET 0x00000001 /* Reset Seeq8003 and HPC interface */ 97 #define SEEQ_HCTL_IPEND 0x00000002 /* IRQ is pending for the chip */ 98 #define SEEQ_HCTL_IPG 0x00001000 /* Inter-packet gap */ 99 #define SEEQ_HCTL_RFIX 0x00002000 /* At rxdc, clear end-of-packet */ 100 #define SEEQ_HCTL_EFIX 0x00004000 /* fixes intr status bit settings */ 101 #define SEEQ_HCTL_IFIX 0x00008000 /* enable startup timeouts */ 102 103 #endif /* !(_SGISEEQ_H) */ 104