1 // SPDX-License-Identifier: GPL-2.0 2 /* Copyright(c) 1999 - 2018 Intel Corporation. */ 3 4 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt 5 6 #include <linux/module.h> 7 #include <linux/types.h> 8 #include <linux/init.h> 9 #include <linux/pci.h> 10 #include <linux/vmalloc.h> 11 #include <linux/pagemap.h> 12 #include <linux/delay.h> 13 #include <linux/netdevice.h> 14 #include <linux/interrupt.h> 15 #include <linux/tcp.h> 16 #include <linux/ipv6.h> 17 #include <linux/slab.h> 18 #include <net/checksum.h> 19 #include <net/ip6_checksum.h> 20 #include <linux/ethtool.h> 21 #include <linux/if_vlan.h> 22 #include <linux/cpu.h> 23 #include <linux/smp.h> 24 #include <linux/pm_qos.h> 25 #include <linux/pm_runtime.h> 26 #include <linux/aer.h> 27 #include <linux/prefetch.h> 28 #include <linux/suspend.h> 29 30 #include "e1000.h" 31 #define CREATE_TRACE_POINTS 32 #include "e1000e_trace.h" 33 34 char e1000e_driver_name[] = "e1000e"; 35 36 #define DEFAULT_MSG_ENABLE (NETIF_MSG_DRV|NETIF_MSG_PROBE|NETIF_MSG_LINK) 37 static int debug = -1; 38 module_param(debug, int, 0); 39 MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)"); 40 41 static const struct e1000_info *e1000_info_tbl[] = { 42 [board_82571] = &e1000_82571_info, 43 [board_82572] = &e1000_82572_info, 44 [board_82573] = &e1000_82573_info, 45 [board_82574] = &e1000_82574_info, 46 [board_82583] = &e1000_82583_info, 47 [board_80003es2lan] = &e1000_es2_info, 48 [board_ich8lan] = &e1000_ich8_info, 49 [board_ich9lan] = &e1000_ich9_info, 50 [board_ich10lan] = &e1000_ich10_info, 51 [board_pchlan] = &e1000_pch_info, 52 [board_pch2lan] = &e1000_pch2_info, 53 [board_pch_lpt] = &e1000_pch_lpt_info, 54 [board_pch_spt] = &e1000_pch_spt_info, 55 [board_pch_cnp] = &e1000_pch_cnp_info, 56 [board_pch_tgp] = &e1000_pch_tgp_info, 57 [board_pch_adp] = &e1000_pch_adp_info, 58 [board_pch_mtp] = &e1000_pch_mtp_info, 59 }; 60 61 struct e1000_reg_info { 62 u32 ofs; 63 char *name; 64 }; 65 66 static const struct e1000_reg_info e1000_reg_info_tbl[] = { 67 /* General Registers */ 68 {E1000_CTRL, "CTRL"}, 69 {E1000_STATUS, "STATUS"}, 70 {E1000_CTRL_EXT, "CTRL_EXT"}, 71 72 /* Interrupt Registers */ 73 {E1000_ICR, "ICR"}, 74 75 /* Rx Registers */ 76 {E1000_RCTL, "RCTL"}, 77 {E1000_RDLEN(0), "RDLEN"}, 78 {E1000_RDH(0), "RDH"}, 79 {E1000_RDT(0), "RDT"}, 80 {E1000_RDTR, "RDTR"}, 81 {E1000_RXDCTL(0), "RXDCTL"}, 82 {E1000_ERT, "ERT"}, 83 {E1000_RDBAL(0), "RDBAL"}, 84 {E1000_RDBAH(0), "RDBAH"}, 85 {E1000_RDFH, "RDFH"}, 86 {E1000_RDFT, "RDFT"}, 87 {E1000_RDFHS, "RDFHS"}, 88 {E1000_RDFTS, "RDFTS"}, 89 {E1000_RDFPC, "RDFPC"}, 90 91 /* Tx Registers */ 92 {E1000_TCTL, "TCTL"}, 93 {E1000_TDBAL(0), "TDBAL"}, 94 {E1000_TDBAH(0), "TDBAH"}, 95 {E1000_TDLEN(0), "TDLEN"}, 96 {E1000_TDH(0), "TDH"}, 97 {E1000_TDT(0), "TDT"}, 98 {E1000_TIDV, "TIDV"}, 99 {E1000_TXDCTL(0), "TXDCTL"}, 100 {E1000_TADV, "TADV"}, 101 {E1000_TARC(0), "TARC"}, 102 {E1000_TDFH, "TDFH"}, 103 {E1000_TDFT, "TDFT"}, 104 {E1000_TDFHS, "TDFHS"}, 105 {E1000_TDFTS, "TDFTS"}, 106 {E1000_TDFPC, "TDFPC"}, 107 108 /* List Terminator */ 109 {0, NULL} 110 }; 111 112 /** 113 * __ew32_prepare - prepare to write to MAC CSR register on certain parts 114 * @hw: pointer to the HW structure 115 * 116 * When updating the MAC CSR registers, the Manageability Engine (ME) could 117 * be accessing the registers at the same time. Normally, this is handled in 118 * h/w by an arbiter but on some parts there is a bug that acknowledges Host 119 * accesses later than it should which could result in the register to have 120 * an incorrect value. Workaround this by checking the FWSM register which 121 * has bit 24 set while ME is accessing MAC CSR registers, wait if it is set 122 * and try again a number of times. 123 **/ 124 static void __ew32_prepare(struct e1000_hw *hw) 125 { 126 s32 i = E1000_ICH_FWSM_PCIM2PCI_COUNT; 127 128 while ((er32(FWSM) & E1000_ICH_FWSM_PCIM2PCI) && --i) 129 udelay(50); 130 } 131 132 void __ew32(struct e1000_hw *hw, unsigned long reg, u32 val) 133 { 134 if (hw->adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA) 135 __ew32_prepare(hw); 136 137 writel(val, hw->hw_addr + reg); 138 } 139 140 /** 141 * e1000_regdump - register printout routine 142 * @hw: pointer to the HW structure 143 * @reginfo: pointer to the register info table 144 **/ 145 static void e1000_regdump(struct e1000_hw *hw, struct e1000_reg_info *reginfo) 146 { 147 int n = 0; 148 char rname[16]; 149 u32 regs[8]; 150 151 switch (reginfo->ofs) { 152 case E1000_RXDCTL(0): 153 for (n = 0; n < 2; n++) 154 regs[n] = __er32(hw, E1000_RXDCTL(n)); 155 break; 156 case E1000_TXDCTL(0): 157 for (n = 0; n < 2; n++) 158 regs[n] = __er32(hw, E1000_TXDCTL(n)); 159 break; 160 case E1000_TARC(0): 161 for (n = 0; n < 2; n++) 162 regs[n] = __er32(hw, E1000_TARC(n)); 163 break; 164 default: 165 pr_info("%-15s %08x\n", 166 reginfo->name, __er32(hw, reginfo->ofs)); 167 return; 168 } 169 170 snprintf(rname, 16, "%s%s", reginfo->name, "[0-1]"); 171 pr_info("%-15s %08x %08x\n", rname, regs[0], regs[1]); 172 } 173 174 static void e1000e_dump_ps_pages(struct e1000_adapter *adapter, 175 struct e1000_buffer *bi) 176 { 177 int i; 178 struct e1000_ps_page *ps_page; 179 180 for (i = 0; i < adapter->rx_ps_pages; i++) { 181 ps_page = &bi->ps_pages[i]; 182 183 if (ps_page->page) { 184 pr_info("packet dump for ps_page %d:\n", i); 185 print_hex_dump(KERN_INFO, "", DUMP_PREFIX_ADDRESS, 186 16, 1, page_address(ps_page->page), 187 PAGE_SIZE, true); 188 } 189 } 190 } 191 192 /** 193 * e1000e_dump - Print registers, Tx-ring and Rx-ring 194 * @adapter: board private structure 195 **/ 196 static void e1000e_dump(struct e1000_adapter *adapter) 197 { 198 struct net_device *netdev = adapter->netdev; 199 struct e1000_hw *hw = &adapter->hw; 200 struct e1000_reg_info *reginfo; 201 struct e1000_ring *tx_ring = adapter->tx_ring; 202 struct e1000_tx_desc *tx_desc; 203 struct my_u0 { 204 __le64 a; 205 __le64 b; 206 } *u0; 207 struct e1000_buffer *buffer_info; 208 struct e1000_ring *rx_ring = adapter->rx_ring; 209 union e1000_rx_desc_packet_split *rx_desc_ps; 210 union e1000_rx_desc_extended *rx_desc; 211 struct my_u1 { 212 __le64 a; 213 __le64 b; 214 __le64 c; 215 __le64 d; 216 } *u1; 217 u32 staterr; 218 int i = 0; 219 220 if (!netif_msg_hw(adapter)) 221 return; 222 223 /* Print netdevice Info */ 224 if (netdev) { 225 dev_info(&adapter->pdev->dev, "Net device Info\n"); 226 pr_info("Device Name state trans_start\n"); 227 pr_info("%-15s %016lX %016lX\n", netdev->name, 228 netdev->state, dev_trans_start(netdev)); 229 } 230 231 /* Print Registers */ 232 dev_info(&adapter->pdev->dev, "Register Dump\n"); 233 pr_info(" Register Name Value\n"); 234 for (reginfo = (struct e1000_reg_info *)e1000_reg_info_tbl; 235 reginfo->name; reginfo++) { 236 e1000_regdump(hw, reginfo); 237 } 238 239 /* Print Tx Ring Summary */ 240 if (!netdev || !netif_running(netdev)) 241 return; 242 243 dev_info(&adapter->pdev->dev, "Tx Ring Summary\n"); 244 pr_info("Queue [NTU] [NTC] [bi(ntc)->dma ] leng ntw timestamp\n"); 245 buffer_info = &tx_ring->buffer_info[tx_ring->next_to_clean]; 246 pr_info(" %5d %5X %5X %016llX %04X %3X %016llX\n", 247 0, tx_ring->next_to_use, tx_ring->next_to_clean, 248 (unsigned long long)buffer_info->dma, 249 buffer_info->length, 250 buffer_info->next_to_watch, 251 (unsigned long long)buffer_info->time_stamp); 252 253 /* Print Tx Ring */ 254 if (!netif_msg_tx_done(adapter)) 255 goto rx_ring_summary; 256 257 dev_info(&adapter->pdev->dev, "Tx Ring Dump\n"); 258 259 /* Transmit Descriptor Formats - DEXT[29] is 0 (Legacy) or 1 (Extended) 260 * 261 * Legacy Transmit Descriptor 262 * +--------------------------------------------------------------+ 263 * 0 | Buffer Address [63:0] (Reserved on Write Back) | 264 * +--------------------------------------------------------------+ 265 * 8 | Special | CSS | Status | CMD | CSO | Length | 266 * +--------------------------------------------------------------+ 267 * 63 48 47 36 35 32 31 24 23 16 15 0 268 * 269 * Extended Context Descriptor (DTYP=0x0) for TSO or checksum offload 270 * 63 48 47 40 39 32 31 16 15 8 7 0 271 * +----------------------------------------------------------------+ 272 * 0 | TUCSE | TUCS0 | TUCSS | IPCSE | IPCS0 | IPCSS | 273 * +----------------------------------------------------------------+ 274 * 8 | MSS | HDRLEN | RSV | STA | TUCMD | DTYP | PAYLEN | 275 * +----------------------------------------------------------------+ 276 * 63 48 47 40 39 36 35 32 31 24 23 20 19 0 277 * 278 * Extended Data Descriptor (DTYP=0x1) 279 * +----------------------------------------------------------------+ 280 * 0 | Buffer Address [63:0] | 281 * +----------------------------------------------------------------+ 282 * 8 | VLAN tag | POPTS | Rsvd | Status | Command | DTYP | DTALEN | 283 * +----------------------------------------------------------------+ 284 * 63 48 47 40 39 36 35 32 31 24 23 20 19 0 285 */ 286 pr_info("Tl[desc] [address 63:0 ] [SpeCssSCmCsLen] [bi->dma ] leng ntw timestamp bi->skb <-- Legacy format\n"); 287 pr_info("Tc[desc] [Ce CoCsIpceCoS] [MssHlRSCm0Plen] [bi->dma ] leng ntw timestamp bi->skb <-- Ext Context format\n"); 288 pr_info("Td[desc] [address 63:0 ] [VlaPoRSCm1Dlen] [bi->dma ] leng ntw timestamp bi->skb <-- Ext Data format\n"); 289 for (i = 0; tx_ring->desc && (i < tx_ring->count); i++) { 290 const char *next_desc; 291 tx_desc = E1000_TX_DESC(*tx_ring, i); 292 buffer_info = &tx_ring->buffer_info[i]; 293 u0 = (struct my_u0 *)tx_desc; 294 if (i == tx_ring->next_to_use && i == tx_ring->next_to_clean) 295 next_desc = " NTC/U"; 296 else if (i == tx_ring->next_to_use) 297 next_desc = " NTU"; 298 else if (i == tx_ring->next_to_clean) 299 next_desc = " NTC"; 300 else 301 next_desc = ""; 302 pr_info("T%c[0x%03X] %016llX %016llX %016llX %04X %3X %016llX %p%s\n", 303 (!(le64_to_cpu(u0->b) & BIT(29)) ? 'l' : 304 ((le64_to_cpu(u0->b) & BIT(20)) ? 'd' : 'c')), 305 i, 306 (unsigned long long)le64_to_cpu(u0->a), 307 (unsigned long long)le64_to_cpu(u0->b), 308 (unsigned long long)buffer_info->dma, 309 buffer_info->length, buffer_info->next_to_watch, 310 (unsigned long long)buffer_info->time_stamp, 311 buffer_info->skb, next_desc); 312 313 if (netif_msg_pktdata(adapter) && buffer_info->skb) 314 print_hex_dump(KERN_INFO, "", DUMP_PREFIX_ADDRESS, 315 16, 1, buffer_info->skb->data, 316 buffer_info->skb->len, true); 317 } 318 319 /* Print Rx Ring Summary */ 320 rx_ring_summary: 321 dev_info(&adapter->pdev->dev, "Rx Ring Summary\n"); 322 pr_info("Queue [NTU] [NTC]\n"); 323 pr_info(" %5d %5X %5X\n", 324 0, rx_ring->next_to_use, rx_ring->next_to_clean); 325 326 /* Print Rx Ring */ 327 if (!netif_msg_rx_status(adapter)) 328 return; 329 330 dev_info(&adapter->pdev->dev, "Rx Ring Dump\n"); 331 switch (adapter->rx_ps_pages) { 332 case 1: 333 case 2: 334 case 3: 335 /* [Extended] Packet Split Receive Descriptor Format 336 * 337 * +-----------------------------------------------------+ 338 * 0 | Buffer Address 0 [63:0] | 339 * +-----------------------------------------------------+ 340 * 8 | Buffer Address 1 [63:0] | 341 * +-----------------------------------------------------+ 342 * 16 | Buffer Address 2 [63:0] | 343 * +-----------------------------------------------------+ 344 * 24 | Buffer Address 3 [63:0] | 345 * +-----------------------------------------------------+ 346 */ 347 pr_info("R [desc] [buffer 0 63:0 ] [buffer 1 63:0 ] [buffer 2 63:0 ] [buffer 3 63:0 ] [bi->dma ] [bi->skb] <-- Ext Pkt Split format\n"); 348 /* [Extended] Receive Descriptor (Write-Back) Format 349 * 350 * 63 48 47 32 31 13 12 8 7 4 3 0 351 * +------------------------------------------------------+ 352 * 0 | Packet | IP | Rsvd | MRQ | Rsvd | MRQ RSS | 353 * | Checksum | Ident | | Queue | | Type | 354 * +------------------------------------------------------+ 355 * 8 | VLAN Tag | Length | Extended Error | Extended Status | 356 * +------------------------------------------------------+ 357 * 63 48 47 32 31 20 19 0 358 */ 359 pr_info("RWB[desc] [ck ipid mrqhsh] [vl l0 ee es] [ l3 l2 l1 hs] [reserved ] ---------------- [bi->skb] <-- Ext Rx Write-Back format\n"); 360 for (i = 0; i < rx_ring->count; i++) { 361 const char *next_desc; 362 buffer_info = &rx_ring->buffer_info[i]; 363 rx_desc_ps = E1000_RX_DESC_PS(*rx_ring, i); 364 u1 = (struct my_u1 *)rx_desc_ps; 365 staterr = 366 le32_to_cpu(rx_desc_ps->wb.middle.status_error); 367 368 if (i == rx_ring->next_to_use) 369 next_desc = " NTU"; 370 else if (i == rx_ring->next_to_clean) 371 next_desc = " NTC"; 372 else 373 next_desc = ""; 374 375 if (staterr & E1000_RXD_STAT_DD) { 376 /* Descriptor Done */ 377 pr_info("%s[0x%03X] %016llX %016llX %016llX %016llX ---------------- %p%s\n", 378 "RWB", i, 379 (unsigned long long)le64_to_cpu(u1->a), 380 (unsigned long long)le64_to_cpu(u1->b), 381 (unsigned long long)le64_to_cpu(u1->c), 382 (unsigned long long)le64_to_cpu(u1->d), 383 buffer_info->skb, next_desc); 384 } else { 385 pr_info("%s[0x%03X] %016llX %016llX %016llX %016llX %016llX %p%s\n", 386 "R ", i, 387 (unsigned long long)le64_to_cpu(u1->a), 388 (unsigned long long)le64_to_cpu(u1->b), 389 (unsigned long long)le64_to_cpu(u1->c), 390 (unsigned long long)le64_to_cpu(u1->d), 391 (unsigned long long)buffer_info->dma, 392 buffer_info->skb, next_desc); 393 394 if (netif_msg_pktdata(adapter)) 395 e1000e_dump_ps_pages(adapter, 396 buffer_info); 397 } 398 } 399 break; 400 default: 401 case 0: 402 /* Extended Receive Descriptor (Read) Format 403 * 404 * +-----------------------------------------------------+ 405 * 0 | Buffer Address [63:0] | 406 * +-----------------------------------------------------+ 407 * 8 | Reserved | 408 * +-----------------------------------------------------+ 409 */ 410 pr_info("R [desc] [buf addr 63:0 ] [reserved 63:0 ] [bi->dma ] [bi->skb] <-- Ext (Read) format\n"); 411 /* Extended Receive Descriptor (Write-Back) Format 412 * 413 * 63 48 47 32 31 24 23 4 3 0 414 * +------------------------------------------------------+ 415 * | RSS Hash | | | | 416 * 0 +-------------------+ Rsvd | Reserved | MRQ RSS | 417 * | Packet | IP | | | Type | 418 * | Checksum | Ident | | | | 419 * +------------------------------------------------------+ 420 * 8 | VLAN Tag | Length | Extended Error | Extended Status | 421 * +------------------------------------------------------+ 422 * 63 48 47 32 31 20 19 0 423 */ 424 pr_info("RWB[desc] [cs ipid mrq] [vt ln xe xs] [bi->skb] <-- Ext (Write-Back) format\n"); 425 426 for (i = 0; i < rx_ring->count; i++) { 427 const char *next_desc; 428 429 buffer_info = &rx_ring->buffer_info[i]; 430 rx_desc = E1000_RX_DESC_EXT(*rx_ring, i); 431 u1 = (struct my_u1 *)rx_desc; 432 staterr = le32_to_cpu(rx_desc->wb.upper.status_error); 433 434 if (i == rx_ring->next_to_use) 435 next_desc = " NTU"; 436 else if (i == rx_ring->next_to_clean) 437 next_desc = " NTC"; 438 else 439 next_desc = ""; 440 441 if (staterr & E1000_RXD_STAT_DD) { 442 /* Descriptor Done */ 443 pr_info("%s[0x%03X] %016llX %016llX ---------------- %p%s\n", 444 "RWB", i, 445 (unsigned long long)le64_to_cpu(u1->a), 446 (unsigned long long)le64_to_cpu(u1->b), 447 buffer_info->skb, next_desc); 448 } else { 449 pr_info("%s[0x%03X] %016llX %016llX %016llX %p%s\n", 450 "R ", i, 451 (unsigned long long)le64_to_cpu(u1->a), 452 (unsigned long long)le64_to_cpu(u1->b), 453 (unsigned long long)buffer_info->dma, 454 buffer_info->skb, next_desc); 455 456 if (netif_msg_pktdata(adapter) && 457 buffer_info->skb) 458 print_hex_dump(KERN_INFO, "", 459 DUMP_PREFIX_ADDRESS, 16, 460 1, 461 buffer_info->skb->data, 462 adapter->rx_buffer_len, 463 true); 464 } 465 } 466 } 467 } 468 469 /** 470 * e1000_desc_unused - calculate if we have unused descriptors 471 * @ring: pointer to ring struct to perform calculation on 472 **/ 473 static int e1000_desc_unused(struct e1000_ring *ring) 474 { 475 if (ring->next_to_clean > ring->next_to_use) 476 return ring->next_to_clean - ring->next_to_use - 1; 477 478 return ring->count + ring->next_to_clean - ring->next_to_use - 1; 479 } 480 481 /** 482 * e1000e_systim_to_hwtstamp - convert system time value to hw time stamp 483 * @adapter: board private structure 484 * @hwtstamps: time stamp structure to update 485 * @systim: unsigned 64bit system time value. 486 * 487 * Convert the system time value stored in the RX/TXSTMP registers into a 488 * hwtstamp which can be used by the upper level time stamping functions. 489 * 490 * The 'systim_lock' spinlock is used to protect the consistency of the 491 * system time value. This is needed because reading the 64 bit time 492 * value involves reading two 32 bit registers. The first read latches the 493 * value. 494 **/ 495 static void e1000e_systim_to_hwtstamp(struct e1000_adapter *adapter, 496 struct skb_shared_hwtstamps *hwtstamps, 497 u64 systim) 498 { 499 u64 ns; 500 unsigned long flags; 501 502 spin_lock_irqsave(&adapter->systim_lock, flags); 503 ns = timecounter_cyc2time(&adapter->tc, systim); 504 spin_unlock_irqrestore(&adapter->systim_lock, flags); 505 506 memset(hwtstamps, 0, sizeof(*hwtstamps)); 507 hwtstamps->hwtstamp = ns_to_ktime(ns); 508 } 509 510 /** 511 * e1000e_rx_hwtstamp - utility function which checks for Rx time stamp 512 * @adapter: board private structure 513 * @status: descriptor extended error and status field 514 * @skb: particular skb to include time stamp 515 * 516 * If the time stamp is valid, convert it into the timecounter ns value 517 * and store that result into the shhwtstamps structure which is passed 518 * up the network stack. 519 **/ 520 static void e1000e_rx_hwtstamp(struct e1000_adapter *adapter, u32 status, 521 struct sk_buff *skb) 522 { 523 struct e1000_hw *hw = &adapter->hw; 524 u64 rxstmp; 525 526 if (!(adapter->flags & FLAG_HAS_HW_TIMESTAMP) || 527 !(status & E1000_RXDEXT_STATERR_TST) || 528 !(er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_VALID)) 529 return; 530 531 /* The Rx time stamp registers contain the time stamp. No other 532 * received packet will be time stamped until the Rx time stamp 533 * registers are read. Because only one packet can be time stamped 534 * at a time, the register values must belong to this packet and 535 * therefore none of the other additional attributes need to be 536 * compared. 537 */ 538 rxstmp = (u64)er32(RXSTMPL); 539 rxstmp |= (u64)er32(RXSTMPH) << 32; 540 e1000e_systim_to_hwtstamp(adapter, skb_hwtstamps(skb), rxstmp); 541 542 adapter->flags2 &= ~FLAG2_CHECK_RX_HWTSTAMP; 543 } 544 545 /** 546 * e1000_receive_skb - helper function to handle Rx indications 547 * @adapter: board private structure 548 * @netdev: pointer to netdev struct 549 * @staterr: descriptor extended error and status field as written by hardware 550 * @vlan: descriptor vlan field as written by hardware (no le/be conversion) 551 * @skb: pointer to sk_buff to be indicated to stack 552 **/ 553 static void e1000_receive_skb(struct e1000_adapter *adapter, 554 struct net_device *netdev, struct sk_buff *skb, 555 u32 staterr, __le16 vlan) 556 { 557 u16 tag = le16_to_cpu(vlan); 558 559 e1000e_rx_hwtstamp(adapter, staterr, skb); 560 561 skb->protocol = eth_type_trans(skb, netdev); 562 563 if (staterr & E1000_RXD_STAT_VP) 564 __vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q), tag); 565 566 napi_gro_receive(&adapter->napi, skb); 567 } 568 569 /** 570 * e1000_rx_checksum - Receive Checksum Offload 571 * @adapter: board private structure 572 * @status_err: receive descriptor status and error fields 573 * @skb: socket buffer with received data 574 **/ 575 static void e1000_rx_checksum(struct e1000_adapter *adapter, u32 status_err, 576 struct sk_buff *skb) 577 { 578 u16 status = (u16)status_err; 579 u8 errors = (u8)(status_err >> 24); 580 581 skb_checksum_none_assert(skb); 582 583 /* Rx checksum disabled */ 584 if (!(adapter->netdev->features & NETIF_F_RXCSUM)) 585 return; 586 587 /* Ignore Checksum bit is set */ 588 if (status & E1000_RXD_STAT_IXSM) 589 return; 590 591 /* TCP/UDP checksum error bit or IP checksum error bit is set */ 592 if (errors & (E1000_RXD_ERR_TCPE | E1000_RXD_ERR_IPE)) { 593 /* let the stack verify checksum errors */ 594 adapter->hw_csum_err++; 595 return; 596 } 597 598 /* TCP/UDP Checksum has not been calculated */ 599 if (!(status & (E1000_RXD_STAT_TCPCS | E1000_RXD_STAT_UDPCS))) 600 return; 601 602 /* It must be a TCP or UDP packet with a valid checksum */ 603 skb->ip_summed = CHECKSUM_UNNECESSARY; 604 adapter->hw_csum_good++; 605 } 606 607 static void e1000e_update_rdt_wa(struct e1000_ring *rx_ring, unsigned int i) 608 { 609 struct e1000_adapter *adapter = rx_ring->adapter; 610 struct e1000_hw *hw = &adapter->hw; 611 612 __ew32_prepare(hw); 613 writel(i, rx_ring->tail); 614 615 if (unlikely(i != readl(rx_ring->tail))) { 616 u32 rctl = er32(RCTL); 617 618 ew32(RCTL, rctl & ~E1000_RCTL_EN); 619 e_err("ME firmware caused invalid RDT - resetting\n"); 620 schedule_work(&adapter->reset_task); 621 } 622 } 623 624 static void e1000e_update_tdt_wa(struct e1000_ring *tx_ring, unsigned int i) 625 { 626 struct e1000_adapter *adapter = tx_ring->adapter; 627 struct e1000_hw *hw = &adapter->hw; 628 629 __ew32_prepare(hw); 630 writel(i, tx_ring->tail); 631 632 if (unlikely(i != readl(tx_ring->tail))) { 633 u32 tctl = er32(TCTL); 634 635 ew32(TCTL, tctl & ~E1000_TCTL_EN); 636 e_err("ME firmware caused invalid TDT - resetting\n"); 637 schedule_work(&adapter->reset_task); 638 } 639 } 640 641 /** 642 * e1000_alloc_rx_buffers - Replace used receive buffers 643 * @rx_ring: Rx descriptor ring 644 * @cleaned_count: number to reallocate 645 * @gfp: flags for allocation 646 **/ 647 static void e1000_alloc_rx_buffers(struct e1000_ring *rx_ring, 648 int cleaned_count, gfp_t gfp) 649 { 650 struct e1000_adapter *adapter = rx_ring->adapter; 651 struct net_device *netdev = adapter->netdev; 652 struct pci_dev *pdev = adapter->pdev; 653 union e1000_rx_desc_extended *rx_desc; 654 struct e1000_buffer *buffer_info; 655 struct sk_buff *skb; 656 unsigned int i; 657 unsigned int bufsz = adapter->rx_buffer_len; 658 659 i = rx_ring->next_to_use; 660 buffer_info = &rx_ring->buffer_info[i]; 661 662 while (cleaned_count--) { 663 skb = buffer_info->skb; 664 if (skb) { 665 skb_trim(skb, 0); 666 goto map_skb; 667 } 668 669 skb = __netdev_alloc_skb_ip_align(netdev, bufsz, gfp); 670 if (!skb) { 671 /* Better luck next round */ 672 adapter->alloc_rx_buff_failed++; 673 break; 674 } 675 676 buffer_info->skb = skb; 677 map_skb: 678 buffer_info->dma = dma_map_single(&pdev->dev, skb->data, 679 adapter->rx_buffer_len, 680 DMA_FROM_DEVICE); 681 if (dma_mapping_error(&pdev->dev, buffer_info->dma)) { 682 dev_err(&pdev->dev, "Rx DMA map failed\n"); 683 adapter->rx_dma_failed++; 684 break; 685 } 686 687 rx_desc = E1000_RX_DESC_EXT(*rx_ring, i); 688 rx_desc->read.buffer_addr = cpu_to_le64(buffer_info->dma); 689 690 if (unlikely(!(i & (E1000_RX_BUFFER_WRITE - 1)))) { 691 /* Force memory writes to complete before letting h/w 692 * know there are new descriptors to fetch. (Only 693 * applicable for weak-ordered memory model archs, 694 * such as IA-64). 695 */ 696 wmb(); 697 if (adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA) 698 e1000e_update_rdt_wa(rx_ring, i); 699 else 700 writel(i, rx_ring->tail); 701 } 702 i++; 703 if (i == rx_ring->count) 704 i = 0; 705 buffer_info = &rx_ring->buffer_info[i]; 706 } 707 708 rx_ring->next_to_use = i; 709 } 710 711 /** 712 * e1000_alloc_rx_buffers_ps - Replace used receive buffers; packet split 713 * @rx_ring: Rx descriptor ring 714 * @cleaned_count: number to reallocate 715 * @gfp: flags for allocation 716 **/ 717 static void e1000_alloc_rx_buffers_ps(struct e1000_ring *rx_ring, 718 int cleaned_count, gfp_t gfp) 719 { 720 struct e1000_adapter *adapter = rx_ring->adapter; 721 struct net_device *netdev = adapter->netdev; 722 struct pci_dev *pdev = adapter->pdev; 723 union e1000_rx_desc_packet_split *rx_desc; 724 struct e1000_buffer *buffer_info; 725 struct e1000_ps_page *ps_page; 726 struct sk_buff *skb; 727 unsigned int i, j; 728 729 i = rx_ring->next_to_use; 730 buffer_info = &rx_ring->buffer_info[i]; 731 732 while (cleaned_count--) { 733 rx_desc = E1000_RX_DESC_PS(*rx_ring, i); 734 735 for (j = 0; j < PS_PAGE_BUFFERS; j++) { 736 ps_page = &buffer_info->ps_pages[j]; 737 if (j >= adapter->rx_ps_pages) { 738 /* all unused desc entries get hw null ptr */ 739 rx_desc->read.buffer_addr[j + 1] = 740 ~cpu_to_le64(0); 741 continue; 742 } 743 if (!ps_page->page) { 744 ps_page->page = alloc_page(gfp); 745 if (!ps_page->page) { 746 adapter->alloc_rx_buff_failed++; 747 goto no_buffers; 748 } 749 ps_page->dma = dma_map_page(&pdev->dev, 750 ps_page->page, 751 0, PAGE_SIZE, 752 DMA_FROM_DEVICE); 753 if (dma_mapping_error(&pdev->dev, 754 ps_page->dma)) { 755 dev_err(&adapter->pdev->dev, 756 "Rx DMA page map failed\n"); 757 adapter->rx_dma_failed++; 758 goto no_buffers; 759 } 760 } 761 /* Refresh the desc even if buffer_addrs 762 * didn't change because each write-back 763 * erases this info. 764 */ 765 rx_desc->read.buffer_addr[j + 1] = 766 cpu_to_le64(ps_page->dma); 767 } 768 769 skb = __netdev_alloc_skb_ip_align(netdev, adapter->rx_ps_bsize0, 770 gfp); 771 772 if (!skb) { 773 adapter->alloc_rx_buff_failed++; 774 break; 775 } 776 777 buffer_info->skb = skb; 778 buffer_info->dma = dma_map_single(&pdev->dev, skb->data, 779 adapter->rx_ps_bsize0, 780 DMA_FROM_DEVICE); 781 if (dma_mapping_error(&pdev->dev, buffer_info->dma)) { 782 dev_err(&pdev->dev, "Rx DMA map failed\n"); 783 adapter->rx_dma_failed++; 784 /* cleanup skb */ 785 dev_kfree_skb_any(skb); 786 buffer_info->skb = NULL; 787 break; 788 } 789 790 rx_desc->read.buffer_addr[0] = cpu_to_le64(buffer_info->dma); 791 792 if (unlikely(!(i & (E1000_RX_BUFFER_WRITE - 1)))) { 793 /* Force memory writes to complete before letting h/w 794 * know there are new descriptors to fetch. (Only 795 * applicable for weak-ordered memory model archs, 796 * such as IA-64). 797 */ 798 wmb(); 799 if (adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA) 800 e1000e_update_rdt_wa(rx_ring, i << 1); 801 else 802 writel(i << 1, rx_ring->tail); 803 } 804 805 i++; 806 if (i == rx_ring->count) 807 i = 0; 808 buffer_info = &rx_ring->buffer_info[i]; 809 } 810 811 no_buffers: 812 rx_ring->next_to_use = i; 813 } 814 815 /** 816 * e1000_alloc_jumbo_rx_buffers - Replace used jumbo receive buffers 817 * @rx_ring: Rx descriptor ring 818 * @cleaned_count: number of buffers to allocate this pass 819 * @gfp: flags for allocation 820 **/ 821 822 static void e1000_alloc_jumbo_rx_buffers(struct e1000_ring *rx_ring, 823 int cleaned_count, gfp_t gfp) 824 { 825 struct e1000_adapter *adapter = rx_ring->adapter; 826 struct net_device *netdev = adapter->netdev; 827 struct pci_dev *pdev = adapter->pdev; 828 union e1000_rx_desc_extended *rx_desc; 829 struct e1000_buffer *buffer_info; 830 struct sk_buff *skb; 831 unsigned int i; 832 unsigned int bufsz = 256 - 16; /* for skb_reserve */ 833 834 i = rx_ring->next_to_use; 835 buffer_info = &rx_ring->buffer_info[i]; 836 837 while (cleaned_count--) { 838 skb = buffer_info->skb; 839 if (skb) { 840 skb_trim(skb, 0); 841 goto check_page; 842 } 843 844 skb = __netdev_alloc_skb_ip_align(netdev, bufsz, gfp); 845 if (unlikely(!skb)) { 846 /* Better luck next round */ 847 adapter->alloc_rx_buff_failed++; 848 break; 849 } 850 851 buffer_info->skb = skb; 852 check_page: 853 /* allocate a new page if necessary */ 854 if (!buffer_info->page) { 855 buffer_info->page = alloc_page(gfp); 856 if (unlikely(!buffer_info->page)) { 857 adapter->alloc_rx_buff_failed++; 858 break; 859 } 860 } 861 862 if (!buffer_info->dma) { 863 buffer_info->dma = dma_map_page(&pdev->dev, 864 buffer_info->page, 0, 865 PAGE_SIZE, 866 DMA_FROM_DEVICE); 867 if (dma_mapping_error(&pdev->dev, buffer_info->dma)) { 868 adapter->alloc_rx_buff_failed++; 869 break; 870 } 871 } 872 873 rx_desc = E1000_RX_DESC_EXT(*rx_ring, i); 874 rx_desc->read.buffer_addr = cpu_to_le64(buffer_info->dma); 875 876 if (unlikely(++i == rx_ring->count)) 877 i = 0; 878 buffer_info = &rx_ring->buffer_info[i]; 879 } 880 881 if (likely(rx_ring->next_to_use != i)) { 882 rx_ring->next_to_use = i; 883 if (unlikely(i-- == 0)) 884 i = (rx_ring->count - 1); 885 886 /* Force memory writes to complete before letting h/w 887 * know there are new descriptors to fetch. (Only 888 * applicable for weak-ordered memory model archs, 889 * such as IA-64). 890 */ 891 wmb(); 892 if (adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA) 893 e1000e_update_rdt_wa(rx_ring, i); 894 else 895 writel(i, rx_ring->tail); 896 } 897 } 898 899 static inline void e1000_rx_hash(struct net_device *netdev, __le32 rss, 900 struct sk_buff *skb) 901 { 902 if (netdev->features & NETIF_F_RXHASH) 903 skb_set_hash(skb, le32_to_cpu(rss), PKT_HASH_TYPE_L3); 904 } 905 906 /** 907 * e1000_clean_rx_irq - Send received data up the network stack 908 * @rx_ring: Rx descriptor ring 909 * @work_done: output parameter for indicating completed work 910 * @work_to_do: how many packets we can clean 911 * 912 * the return value indicates whether actual cleaning was done, there 913 * is no guarantee that everything was cleaned 914 **/ 915 static bool e1000_clean_rx_irq(struct e1000_ring *rx_ring, int *work_done, 916 int work_to_do) 917 { 918 struct e1000_adapter *adapter = rx_ring->adapter; 919 struct net_device *netdev = adapter->netdev; 920 struct pci_dev *pdev = adapter->pdev; 921 struct e1000_hw *hw = &adapter->hw; 922 union e1000_rx_desc_extended *rx_desc, *next_rxd; 923 struct e1000_buffer *buffer_info, *next_buffer; 924 u32 length, staterr; 925 unsigned int i; 926 int cleaned_count = 0; 927 bool cleaned = false; 928 unsigned int total_rx_bytes = 0, total_rx_packets = 0; 929 930 i = rx_ring->next_to_clean; 931 rx_desc = E1000_RX_DESC_EXT(*rx_ring, i); 932 staterr = le32_to_cpu(rx_desc->wb.upper.status_error); 933 buffer_info = &rx_ring->buffer_info[i]; 934 935 while (staterr & E1000_RXD_STAT_DD) { 936 struct sk_buff *skb; 937 938 if (*work_done >= work_to_do) 939 break; 940 (*work_done)++; 941 dma_rmb(); /* read descriptor and rx_buffer_info after status DD */ 942 943 skb = buffer_info->skb; 944 buffer_info->skb = NULL; 945 946 prefetch(skb->data - NET_IP_ALIGN); 947 948 i++; 949 if (i == rx_ring->count) 950 i = 0; 951 next_rxd = E1000_RX_DESC_EXT(*rx_ring, i); 952 prefetch(next_rxd); 953 954 next_buffer = &rx_ring->buffer_info[i]; 955 956 cleaned = true; 957 cleaned_count++; 958 dma_unmap_single(&pdev->dev, buffer_info->dma, 959 adapter->rx_buffer_len, DMA_FROM_DEVICE); 960 buffer_info->dma = 0; 961 962 length = le16_to_cpu(rx_desc->wb.upper.length); 963 964 /* !EOP means multiple descriptors were used to store a single 965 * packet, if that's the case we need to toss it. In fact, we 966 * need to toss every packet with the EOP bit clear and the 967 * next frame that _does_ have the EOP bit set, as it is by 968 * definition only a frame fragment 969 */ 970 if (unlikely(!(staterr & E1000_RXD_STAT_EOP))) 971 adapter->flags2 |= FLAG2_IS_DISCARDING; 972 973 if (adapter->flags2 & FLAG2_IS_DISCARDING) { 974 /* All receives must fit into a single buffer */ 975 e_dbg("Receive packet consumed multiple buffers\n"); 976 /* recycle */ 977 buffer_info->skb = skb; 978 if (staterr & E1000_RXD_STAT_EOP) 979 adapter->flags2 &= ~FLAG2_IS_DISCARDING; 980 goto next_desc; 981 } 982 983 if (unlikely((staterr & E1000_RXDEXT_ERR_FRAME_ERR_MASK) && 984 !(netdev->features & NETIF_F_RXALL))) { 985 /* recycle */ 986 buffer_info->skb = skb; 987 goto next_desc; 988 } 989 990 /* adjust length to remove Ethernet CRC */ 991 if (!(adapter->flags2 & FLAG2_CRC_STRIPPING)) { 992 /* If configured to store CRC, don't subtract FCS, 993 * but keep the FCS bytes out of the total_rx_bytes 994 * counter 995 */ 996 if (netdev->features & NETIF_F_RXFCS) 997 total_rx_bytes -= 4; 998 else 999 length -= 4; 1000 } 1001 1002 total_rx_bytes += length; 1003 total_rx_packets++; 1004 1005 /* code added for copybreak, this should improve 1006 * performance for small packets with large amounts 1007 * of reassembly being done in the stack 1008 */ 1009 if (length < copybreak) { 1010 struct sk_buff *new_skb = 1011 napi_alloc_skb(&adapter->napi, length); 1012 if (new_skb) { 1013 skb_copy_to_linear_data_offset(new_skb, 1014 -NET_IP_ALIGN, 1015 (skb->data - 1016 NET_IP_ALIGN), 1017 (length + 1018 NET_IP_ALIGN)); 1019 /* save the skb in buffer_info as good */ 1020 buffer_info->skb = skb; 1021 skb = new_skb; 1022 } 1023 /* else just continue with the old one */ 1024 } 1025 /* end copybreak code */ 1026 skb_put(skb, length); 1027 1028 /* Receive Checksum Offload */ 1029 e1000_rx_checksum(adapter, staterr, skb); 1030 1031 e1000_rx_hash(netdev, rx_desc->wb.lower.hi_dword.rss, skb); 1032 1033 e1000_receive_skb(adapter, netdev, skb, staterr, 1034 rx_desc->wb.upper.vlan); 1035 1036 next_desc: 1037 rx_desc->wb.upper.status_error &= cpu_to_le32(~0xFF); 1038 1039 /* return some buffers to hardware, one at a time is too slow */ 1040 if (cleaned_count >= E1000_RX_BUFFER_WRITE) { 1041 adapter->alloc_rx_buf(rx_ring, cleaned_count, 1042 GFP_ATOMIC); 1043 cleaned_count = 0; 1044 } 1045 1046 /* use prefetched values */ 1047 rx_desc = next_rxd; 1048 buffer_info = next_buffer; 1049 1050 staterr = le32_to_cpu(rx_desc->wb.upper.status_error); 1051 } 1052 rx_ring->next_to_clean = i; 1053 1054 cleaned_count = e1000_desc_unused(rx_ring); 1055 if (cleaned_count) 1056 adapter->alloc_rx_buf(rx_ring, cleaned_count, GFP_ATOMIC); 1057 1058 adapter->total_rx_bytes += total_rx_bytes; 1059 adapter->total_rx_packets += total_rx_packets; 1060 return cleaned; 1061 } 1062 1063 static void e1000_put_txbuf(struct e1000_ring *tx_ring, 1064 struct e1000_buffer *buffer_info, 1065 bool drop) 1066 { 1067 struct e1000_adapter *adapter = tx_ring->adapter; 1068 1069 if (buffer_info->dma) { 1070 if (buffer_info->mapped_as_page) 1071 dma_unmap_page(&adapter->pdev->dev, buffer_info->dma, 1072 buffer_info->length, DMA_TO_DEVICE); 1073 else 1074 dma_unmap_single(&adapter->pdev->dev, buffer_info->dma, 1075 buffer_info->length, DMA_TO_DEVICE); 1076 buffer_info->dma = 0; 1077 } 1078 if (buffer_info->skb) { 1079 if (drop) 1080 dev_kfree_skb_any(buffer_info->skb); 1081 else 1082 dev_consume_skb_any(buffer_info->skb); 1083 buffer_info->skb = NULL; 1084 } 1085 buffer_info->time_stamp = 0; 1086 } 1087 1088 static void e1000_print_hw_hang(struct work_struct *work) 1089 { 1090 struct e1000_adapter *adapter = container_of(work, 1091 struct e1000_adapter, 1092 print_hang_task); 1093 struct net_device *netdev = adapter->netdev; 1094 struct e1000_ring *tx_ring = adapter->tx_ring; 1095 unsigned int i = tx_ring->next_to_clean; 1096 unsigned int eop = tx_ring->buffer_info[i].next_to_watch; 1097 struct e1000_tx_desc *eop_desc = E1000_TX_DESC(*tx_ring, eop); 1098 struct e1000_hw *hw = &adapter->hw; 1099 u16 phy_status, phy_1000t_status, phy_ext_status; 1100 u16 pci_status; 1101 1102 if (test_bit(__E1000_DOWN, &adapter->state)) 1103 return; 1104 1105 if (!adapter->tx_hang_recheck && (adapter->flags2 & FLAG2_DMA_BURST)) { 1106 /* May be block on write-back, flush and detect again 1107 * flush pending descriptor writebacks to memory 1108 */ 1109 ew32(TIDV, adapter->tx_int_delay | E1000_TIDV_FPD); 1110 /* execute the writes immediately */ 1111 e1e_flush(); 1112 /* Due to rare timing issues, write to TIDV again to ensure 1113 * the write is successful 1114 */ 1115 ew32(TIDV, adapter->tx_int_delay | E1000_TIDV_FPD); 1116 /* execute the writes immediately */ 1117 e1e_flush(); 1118 adapter->tx_hang_recheck = true; 1119 return; 1120 } 1121 adapter->tx_hang_recheck = false; 1122 1123 if (er32(TDH(0)) == er32(TDT(0))) { 1124 e_dbg("false hang detected, ignoring\n"); 1125 return; 1126 } 1127 1128 /* Real hang detected */ 1129 netif_stop_queue(netdev); 1130 1131 e1e_rphy(hw, MII_BMSR, &phy_status); 1132 e1e_rphy(hw, MII_STAT1000, &phy_1000t_status); 1133 e1e_rphy(hw, MII_ESTATUS, &phy_ext_status); 1134 1135 pci_read_config_word(adapter->pdev, PCI_STATUS, &pci_status); 1136 1137 /* detected Hardware unit hang */ 1138 e_err("Detected Hardware Unit Hang:\n" 1139 " TDH <%x>\n" 1140 " TDT <%x>\n" 1141 " next_to_use <%x>\n" 1142 " next_to_clean <%x>\n" 1143 "buffer_info[next_to_clean]:\n" 1144 " time_stamp <%lx>\n" 1145 " next_to_watch <%x>\n" 1146 " jiffies <%lx>\n" 1147 " next_to_watch.status <%x>\n" 1148 "MAC Status <%x>\n" 1149 "PHY Status <%x>\n" 1150 "PHY 1000BASE-T Status <%x>\n" 1151 "PHY Extended Status <%x>\n" 1152 "PCI Status <%x>\n", 1153 readl(tx_ring->head), readl(tx_ring->tail), tx_ring->next_to_use, 1154 tx_ring->next_to_clean, tx_ring->buffer_info[eop].time_stamp, 1155 eop, jiffies, eop_desc->upper.fields.status, er32(STATUS), 1156 phy_status, phy_1000t_status, phy_ext_status, pci_status); 1157 1158 e1000e_dump(adapter); 1159 1160 /* Suggest workaround for known h/w issue */ 1161 if ((hw->mac.type == e1000_pchlan) && (er32(CTRL) & E1000_CTRL_TFCE)) 1162 e_err("Try turning off Tx pause (flow control) via ethtool\n"); 1163 } 1164 1165 /** 1166 * e1000e_tx_hwtstamp_work - check for Tx time stamp 1167 * @work: pointer to work struct 1168 * 1169 * This work function polls the TSYNCTXCTL valid bit to determine when a 1170 * timestamp has been taken for the current stored skb. The timestamp must 1171 * be for this skb because only one such packet is allowed in the queue. 1172 */ 1173 static void e1000e_tx_hwtstamp_work(struct work_struct *work) 1174 { 1175 struct e1000_adapter *adapter = container_of(work, struct e1000_adapter, 1176 tx_hwtstamp_work); 1177 struct e1000_hw *hw = &adapter->hw; 1178 1179 if (er32(TSYNCTXCTL) & E1000_TSYNCTXCTL_VALID) { 1180 struct sk_buff *skb = adapter->tx_hwtstamp_skb; 1181 struct skb_shared_hwtstamps shhwtstamps; 1182 u64 txstmp; 1183 1184 txstmp = er32(TXSTMPL); 1185 txstmp |= (u64)er32(TXSTMPH) << 32; 1186 1187 e1000e_systim_to_hwtstamp(adapter, &shhwtstamps, txstmp); 1188 1189 /* Clear the global tx_hwtstamp_skb pointer and force writes 1190 * prior to notifying the stack of a Tx timestamp. 1191 */ 1192 adapter->tx_hwtstamp_skb = NULL; 1193 wmb(); /* force write prior to skb_tstamp_tx */ 1194 1195 skb_tstamp_tx(skb, &shhwtstamps); 1196 dev_consume_skb_any(skb); 1197 } else if (time_after(jiffies, adapter->tx_hwtstamp_start 1198 + adapter->tx_timeout_factor * HZ)) { 1199 dev_kfree_skb_any(adapter->tx_hwtstamp_skb); 1200 adapter->tx_hwtstamp_skb = NULL; 1201 adapter->tx_hwtstamp_timeouts++; 1202 e_warn("clearing Tx timestamp hang\n"); 1203 } else { 1204 /* reschedule to check later */ 1205 schedule_work(&adapter->tx_hwtstamp_work); 1206 } 1207 } 1208 1209 /** 1210 * e1000_clean_tx_irq - Reclaim resources after transmit completes 1211 * @tx_ring: Tx descriptor ring 1212 * 1213 * the return value indicates whether actual cleaning was done, there 1214 * is no guarantee that everything was cleaned 1215 **/ 1216 static bool e1000_clean_tx_irq(struct e1000_ring *tx_ring) 1217 { 1218 struct e1000_adapter *adapter = tx_ring->adapter; 1219 struct net_device *netdev = adapter->netdev; 1220 struct e1000_hw *hw = &adapter->hw; 1221 struct e1000_tx_desc *tx_desc, *eop_desc; 1222 struct e1000_buffer *buffer_info; 1223 unsigned int i, eop; 1224 unsigned int count = 0; 1225 unsigned int total_tx_bytes = 0, total_tx_packets = 0; 1226 unsigned int bytes_compl = 0, pkts_compl = 0; 1227 1228 i = tx_ring->next_to_clean; 1229 eop = tx_ring->buffer_info[i].next_to_watch; 1230 eop_desc = E1000_TX_DESC(*tx_ring, eop); 1231 1232 while ((eop_desc->upper.data & cpu_to_le32(E1000_TXD_STAT_DD)) && 1233 (count < tx_ring->count)) { 1234 bool cleaned = false; 1235 1236 dma_rmb(); /* read buffer_info after eop_desc */ 1237 for (; !cleaned; count++) { 1238 tx_desc = E1000_TX_DESC(*tx_ring, i); 1239 buffer_info = &tx_ring->buffer_info[i]; 1240 cleaned = (i == eop); 1241 1242 if (cleaned) { 1243 total_tx_packets += buffer_info->segs; 1244 total_tx_bytes += buffer_info->bytecount; 1245 if (buffer_info->skb) { 1246 bytes_compl += buffer_info->skb->len; 1247 pkts_compl++; 1248 } 1249 } 1250 1251 e1000_put_txbuf(tx_ring, buffer_info, false); 1252 tx_desc->upper.data = 0; 1253 1254 i++; 1255 if (i == tx_ring->count) 1256 i = 0; 1257 } 1258 1259 if (i == tx_ring->next_to_use) 1260 break; 1261 eop = tx_ring->buffer_info[i].next_to_watch; 1262 eop_desc = E1000_TX_DESC(*tx_ring, eop); 1263 } 1264 1265 tx_ring->next_to_clean = i; 1266 1267 netdev_completed_queue(netdev, pkts_compl, bytes_compl); 1268 1269 #define TX_WAKE_THRESHOLD 32 1270 if (count && netif_carrier_ok(netdev) && 1271 e1000_desc_unused(tx_ring) >= TX_WAKE_THRESHOLD) { 1272 /* Make sure that anybody stopping the queue after this 1273 * sees the new next_to_clean. 1274 */ 1275 smp_mb(); 1276 1277 if (netif_queue_stopped(netdev) && 1278 !(test_bit(__E1000_DOWN, &adapter->state))) { 1279 netif_wake_queue(netdev); 1280 ++adapter->restart_queue; 1281 } 1282 } 1283 1284 if (adapter->detect_tx_hung) { 1285 /* Detect a transmit hang in hardware, this serializes the 1286 * check with the clearing of time_stamp and movement of i 1287 */ 1288 adapter->detect_tx_hung = false; 1289 if (tx_ring->buffer_info[i].time_stamp && 1290 time_after(jiffies, tx_ring->buffer_info[i].time_stamp 1291 + (adapter->tx_timeout_factor * HZ)) && 1292 !(er32(STATUS) & E1000_STATUS_TXOFF)) 1293 schedule_work(&adapter->print_hang_task); 1294 else 1295 adapter->tx_hang_recheck = false; 1296 } 1297 adapter->total_tx_bytes += total_tx_bytes; 1298 adapter->total_tx_packets += total_tx_packets; 1299 return count < tx_ring->count; 1300 } 1301 1302 /** 1303 * e1000_clean_rx_irq_ps - Send received data up the network stack; packet split 1304 * @rx_ring: Rx descriptor ring 1305 * @work_done: output parameter for indicating completed work 1306 * @work_to_do: how many packets we can clean 1307 * 1308 * the return value indicates whether actual cleaning was done, there 1309 * is no guarantee that everything was cleaned 1310 **/ 1311 static bool e1000_clean_rx_irq_ps(struct e1000_ring *rx_ring, int *work_done, 1312 int work_to_do) 1313 { 1314 struct e1000_adapter *adapter = rx_ring->adapter; 1315 struct e1000_hw *hw = &adapter->hw; 1316 union e1000_rx_desc_packet_split *rx_desc, *next_rxd; 1317 struct net_device *netdev = adapter->netdev; 1318 struct pci_dev *pdev = adapter->pdev; 1319 struct e1000_buffer *buffer_info, *next_buffer; 1320 struct e1000_ps_page *ps_page; 1321 struct sk_buff *skb; 1322 unsigned int i, j; 1323 u32 length, staterr; 1324 int cleaned_count = 0; 1325 bool cleaned = false; 1326 unsigned int total_rx_bytes = 0, total_rx_packets = 0; 1327 1328 i = rx_ring->next_to_clean; 1329 rx_desc = E1000_RX_DESC_PS(*rx_ring, i); 1330 staterr = le32_to_cpu(rx_desc->wb.middle.status_error); 1331 buffer_info = &rx_ring->buffer_info[i]; 1332 1333 while (staterr & E1000_RXD_STAT_DD) { 1334 if (*work_done >= work_to_do) 1335 break; 1336 (*work_done)++; 1337 skb = buffer_info->skb; 1338 dma_rmb(); /* read descriptor and rx_buffer_info after status DD */ 1339 1340 /* in the packet split case this is header only */ 1341 prefetch(skb->data - NET_IP_ALIGN); 1342 1343 i++; 1344 if (i == rx_ring->count) 1345 i = 0; 1346 next_rxd = E1000_RX_DESC_PS(*rx_ring, i); 1347 prefetch(next_rxd); 1348 1349 next_buffer = &rx_ring->buffer_info[i]; 1350 1351 cleaned = true; 1352 cleaned_count++; 1353 dma_unmap_single(&pdev->dev, buffer_info->dma, 1354 adapter->rx_ps_bsize0, DMA_FROM_DEVICE); 1355 buffer_info->dma = 0; 1356 1357 /* see !EOP comment in other Rx routine */ 1358 if (!(staterr & E1000_RXD_STAT_EOP)) 1359 adapter->flags2 |= FLAG2_IS_DISCARDING; 1360 1361 if (adapter->flags2 & FLAG2_IS_DISCARDING) { 1362 e_dbg("Packet Split buffers didn't pick up the full packet\n"); 1363 dev_kfree_skb_irq(skb); 1364 if (staterr & E1000_RXD_STAT_EOP) 1365 adapter->flags2 &= ~FLAG2_IS_DISCARDING; 1366 goto next_desc; 1367 } 1368 1369 if (unlikely((staterr & E1000_RXDEXT_ERR_FRAME_ERR_MASK) && 1370 !(netdev->features & NETIF_F_RXALL))) { 1371 dev_kfree_skb_irq(skb); 1372 goto next_desc; 1373 } 1374 1375 length = le16_to_cpu(rx_desc->wb.middle.length0); 1376 1377 if (!length) { 1378 e_dbg("Last part of the packet spanning multiple descriptors\n"); 1379 dev_kfree_skb_irq(skb); 1380 goto next_desc; 1381 } 1382 1383 /* Good Receive */ 1384 skb_put(skb, length); 1385 1386 { 1387 /* this looks ugly, but it seems compiler issues make 1388 * it more efficient than reusing j 1389 */ 1390 int l1 = le16_to_cpu(rx_desc->wb.upper.length[0]); 1391 1392 /* page alloc/put takes too long and effects small 1393 * packet throughput, so unsplit small packets and 1394 * save the alloc/put 1395 */ 1396 if (l1 && (l1 <= copybreak) && 1397 ((length + l1) <= adapter->rx_ps_bsize0)) { 1398 ps_page = &buffer_info->ps_pages[0]; 1399 1400 dma_sync_single_for_cpu(&pdev->dev, 1401 ps_page->dma, 1402 PAGE_SIZE, 1403 DMA_FROM_DEVICE); 1404 memcpy(skb_tail_pointer(skb), 1405 page_address(ps_page->page), l1); 1406 dma_sync_single_for_device(&pdev->dev, 1407 ps_page->dma, 1408 PAGE_SIZE, 1409 DMA_FROM_DEVICE); 1410 1411 /* remove the CRC */ 1412 if (!(adapter->flags2 & FLAG2_CRC_STRIPPING)) { 1413 if (!(netdev->features & NETIF_F_RXFCS)) 1414 l1 -= 4; 1415 } 1416 1417 skb_put(skb, l1); 1418 goto copydone; 1419 } /* if */ 1420 } 1421 1422 for (j = 0; j < PS_PAGE_BUFFERS; j++) { 1423 length = le16_to_cpu(rx_desc->wb.upper.length[j]); 1424 if (!length) 1425 break; 1426 1427 ps_page = &buffer_info->ps_pages[j]; 1428 dma_unmap_page(&pdev->dev, ps_page->dma, PAGE_SIZE, 1429 DMA_FROM_DEVICE); 1430 ps_page->dma = 0; 1431 skb_fill_page_desc(skb, j, ps_page->page, 0, length); 1432 ps_page->page = NULL; 1433 skb->len += length; 1434 skb->data_len += length; 1435 skb->truesize += PAGE_SIZE; 1436 } 1437 1438 /* strip the ethernet crc, problem is we're using pages now so 1439 * this whole operation can get a little cpu intensive 1440 */ 1441 if (!(adapter->flags2 & FLAG2_CRC_STRIPPING)) { 1442 if (!(netdev->features & NETIF_F_RXFCS)) 1443 pskb_trim(skb, skb->len - 4); 1444 } 1445 1446 copydone: 1447 total_rx_bytes += skb->len; 1448 total_rx_packets++; 1449 1450 e1000_rx_checksum(adapter, staterr, skb); 1451 1452 e1000_rx_hash(netdev, rx_desc->wb.lower.hi_dword.rss, skb); 1453 1454 if (rx_desc->wb.upper.header_status & 1455 cpu_to_le16(E1000_RXDPS_HDRSTAT_HDRSP)) 1456 adapter->rx_hdr_split++; 1457 1458 e1000_receive_skb(adapter, netdev, skb, staterr, 1459 rx_desc->wb.middle.vlan); 1460 1461 next_desc: 1462 rx_desc->wb.middle.status_error &= cpu_to_le32(~0xFF); 1463 buffer_info->skb = NULL; 1464 1465 /* return some buffers to hardware, one at a time is too slow */ 1466 if (cleaned_count >= E1000_RX_BUFFER_WRITE) { 1467 adapter->alloc_rx_buf(rx_ring, cleaned_count, 1468 GFP_ATOMIC); 1469 cleaned_count = 0; 1470 } 1471 1472 /* use prefetched values */ 1473 rx_desc = next_rxd; 1474 buffer_info = next_buffer; 1475 1476 staterr = le32_to_cpu(rx_desc->wb.middle.status_error); 1477 } 1478 rx_ring->next_to_clean = i; 1479 1480 cleaned_count = e1000_desc_unused(rx_ring); 1481 if (cleaned_count) 1482 adapter->alloc_rx_buf(rx_ring, cleaned_count, GFP_ATOMIC); 1483 1484 adapter->total_rx_bytes += total_rx_bytes; 1485 adapter->total_rx_packets += total_rx_packets; 1486 return cleaned; 1487 } 1488 1489 static void e1000_consume_page(struct e1000_buffer *bi, struct sk_buff *skb, 1490 u16 length) 1491 { 1492 bi->page = NULL; 1493 skb->len += length; 1494 skb->data_len += length; 1495 skb->truesize += PAGE_SIZE; 1496 } 1497 1498 /** 1499 * e1000_clean_jumbo_rx_irq - Send received data up the network stack; legacy 1500 * @rx_ring: Rx descriptor ring 1501 * @work_done: output parameter for indicating completed work 1502 * @work_to_do: how many packets we can clean 1503 * 1504 * the return value indicates whether actual cleaning was done, there 1505 * is no guarantee that everything was cleaned 1506 **/ 1507 static bool e1000_clean_jumbo_rx_irq(struct e1000_ring *rx_ring, int *work_done, 1508 int work_to_do) 1509 { 1510 struct e1000_adapter *adapter = rx_ring->adapter; 1511 struct net_device *netdev = adapter->netdev; 1512 struct pci_dev *pdev = adapter->pdev; 1513 union e1000_rx_desc_extended *rx_desc, *next_rxd; 1514 struct e1000_buffer *buffer_info, *next_buffer; 1515 u32 length, staterr; 1516 unsigned int i; 1517 int cleaned_count = 0; 1518 bool cleaned = false; 1519 unsigned int total_rx_bytes = 0, total_rx_packets = 0; 1520 struct skb_shared_info *shinfo; 1521 1522 i = rx_ring->next_to_clean; 1523 rx_desc = E1000_RX_DESC_EXT(*rx_ring, i); 1524 staterr = le32_to_cpu(rx_desc->wb.upper.status_error); 1525 buffer_info = &rx_ring->buffer_info[i]; 1526 1527 while (staterr & E1000_RXD_STAT_DD) { 1528 struct sk_buff *skb; 1529 1530 if (*work_done >= work_to_do) 1531 break; 1532 (*work_done)++; 1533 dma_rmb(); /* read descriptor and rx_buffer_info after status DD */ 1534 1535 skb = buffer_info->skb; 1536 buffer_info->skb = NULL; 1537 1538 ++i; 1539 if (i == rx_ring->count) 1540 i = 0; 1541 next_rxd = E1000_RX_DESC_EXT(*rx_ring, i); 1542 prefetch(next_rxd); 1543 1544 next_buffer = &rx_ring->buffer_info[i]; 1545 1546 cleaned = true; 1547 cleaned_count++; 1548 dma_unmap_page(&pdev->dev, buffer_info->dma, PAGE_SIZE, 1549 DMA_FROM_DEVICE); 1550 buffer_info->dma = 0; 1551 1552 length = le16_to_cpu(rx_desc->wb.upper.length); 1553 1554 /* errors is only valid for DD + EOP descriptors */ 1555 if (unlikely((staterr & E1000_RXD_STAT_EOP) && 1556 ((staterr & E1000_RXDEXT_ERR_FRAME_ERR_MASK) && 1557 !(netdev->features & NETIF_F_RXALL)))) { 1558 /* recycle both page and skb */ 1559 buffer_info->skb = skb; 1560 /* an error means any chain goes out the window too */ 1561 if (rx_ring->rx_skb_top) 1562 dev_kfree_skb_irq(rx_ring->rx_skb_top); 1563 rx_ring->rx_skb_top = NULL; 1564 goto next_desc; 1565 } 1566 #define rxtop (rx_ring->rx_skb_top) 1567 if (!(staterr & E1000_RXD_STAT_EOP)) { 1568 /* this descriptor is only the beginning (or middle) */ 1569 if (!rxtop) { 1570 /* this is the beginning of a chain */ 1571 rxtop = skb; 1572 skb_fill_page_desc(rxtop, 0, buffer_info->page, 1573 0, length); 1574 } else { 1575 /* this is the middle of a chain */ 1576 shinfo = skb_shinfo(rxtop); 1577 skb_fill_page_desc(rxtop, shinfo->nr_frags, 1578 buffer_info->page, 0, 1579 length); 1580 /* re-use the skb, only consumed the page */ 1581 buffer_info->skb = skb; 1582 } 1583 e1000_consume_page(buffer_info, rxtop, length); 1584 goto next_desc; 1585 } else { 1586 if (rxtop) { 1587 /* end of the chain */ 1588 shinfo = skb_shinfo(rxtop); 1589 skb_fill_page_desc(rxtop, shinfo->nr_frags, 1590 buffer_info->page, 0, 1591 length); 1592 /* re-use the current skb, we only consumed the 1593 * page 1594 */ 1595 buffer_info->skb = skb; 1596 skb = rxtop; 1597 rxtop = NULL; 1598 e1000_consume_page(buffer_info, skb, length); 1599 } else { 1600 /* no chain, got EOP, this buf is the packet 1601 * copybreak to save the put_page/alloc_page 1602 */ 1603 if (length <= copybreak && 1604 skb_tailroom(skb) >= length) { 1605 memcpy(skb_tail_pointer(skb), 1606 page_address(buffer_info->page), 1607 length); 1608 /* re-use the page, so don't erase 1609 * buffer_info->page 1610 */ 1611 skb_put(skb, length); 1612 } else { 1613 skb_fill_page_desc(skb, 0, 1614 buffer_info->page, 0, 1615 length); 1616 e1000_consume_page(buffer_info, skb, 1617 length); 1618 } 1619 } 1620 } 1621 1622 /* Receive Checksum Offload */ 1623 e1000_rx_checksum(adapter, staterr, skb); 1624 1625 e1000_rx_hash(netdev, rx_desc->wb.lower.hi_dword.rss, skb); 1626 1627 /* probably a little skewed due to removing CRC */ 1628 total_rx_bytes += skb->len; 1629 total_rx_packets++; 1630 1631 /* eth type trans needs skb->data to point to something */ 1632 if (!pskb_may_pull(skb, ETH_HLEN)) { 1633 e_err("pskb_may_pull failed.\n"); 1634 dev_kfree_skb_irq(skb); 1635 goto next_desc; 1636 } 1637 1638 e1000_receive_skb(adapter, netdev, skb, staterr, 1639 rx_desc->wb.upper.vlan); 1640 1641 next_desc: 1642 rx_desc->wb.upper.status_error &= cpu_to_le32(~0xFF); 1643 1644 /* return some buffers to hardware, one at a time is too slow */ 1645 if (unlikely(cleaned_count >= E1000_RX_BUFFER_WRITE)) { 1646 adapter->alloc_rx_buf(rx_ring, cleaned_count, 1647 GFP_ATOMIC); 1648 cleaned_count = 0; 1649 } 1650 1651 /* use prefetched values */ 1652 rx_desc = next_rxd; 1653 buffer_info = next_buffer; 1654 1655 staterr = le32_to_cpu(rx_desc->wb.upper.status_error); 1656 } 1657 rx_ring->next_to_clean = i; 1658 1659 cleaned_count = e1000_desc_unused(rx_ring); 1660 if (cleaned_count) 1661 adapter->alloc_rx_buf(rx_ring, cleaned_count, GFP_ATOMIC); 1662 1663 adapter->total_rx_bytes += total_rx_bytes; 1664 adapter->total_rx_packets += total_rx_packets; 1665 return cleaned; 1666 } 1667 1668 /** 1669 * e1000_clean_rx_ring - Free Rx Buffers per Queue 1670 * @rx_ring: Rx descriptor ring 1671 **/ 1672 static void e1000_clean_rx_ring(struct e1000_ring *rx_ring) 1673 { 1674 struct e1000_adapter *adapter = rx_ring->adapter; 1675 struct e1000_buffer *buffer_info; 1676 struct e1000_ps_page *ps_page; 1677 struct pci_dev *pdev = adapter->pdev; 1678 unsigned int i, j; 1679 1680 /* Free all the Rx ring sk_buffs */ 1681 for (i = 0; i < rx_ring->count; i++) { 1682 buffer_info = &rx_ring->buffer_info[i]; 1683 if (buffer_info->dma) { 1684 if (adapter->clean_rx == e1000_clean_rx_irq) 1685 dma_unmap_single(&pdev->dev, buffer_info->dma, 1686 adapter->rx_buffer_len, 1687 DMA_FROM_DEVICE); 1688 else if (adapter->clean_rx == e1000_clean_jumbo_rx_irq) 1689 dma_unmap_page(&pdev->dev, buffer_info->dma, 1690 PAGE_SIZE, DMA_FROM_DEVICE); 1691 else if (adapter->clean_rx == e1000_clean_rx_irq_ps) 1692 dma_unmap_single(&pdev->dev, buffer_info->dma, 1693 adapter->rx_ps_bsize0, 1694 DMA_FROM_DEVICE); 1695 buffer_info->dma = 0; 1696 } 1697 1698 if (buffer_info->page) { 1699 put_page(buffer_info->page); 1700 buffer_info->page = NULL; 1701 } 1702 1703 if (buffer_info->skb) { 1704 dev_kfree_skb(buffer_info->skb); 1705 buffer_info->skb = NULL; 1706 } 1707 1708 for (j = 0; j < PS_PAGE_BUFFERS; j++) { 1709 ps_page = &buffer_info->ps_pages[j]; 1710 if (!ps_page->page) 1711 break; 1712 dma_unmap_page(&pdev->dev, ps_page->dma, PAGE_SIZE, 1713 DMA_FROM_DEVICE); 1714 ps_page->dma = 0; 1715 put_page(ps_page->page); 1716 ps_page->page = NULL; 1717 } 1718 } 1719 1720 /* there also may be some cached data from a chained receive */ 1721 if (rx_ring->rx_skb_top) { 1722 dev_kfree_skb(rx_ring->rx_skb_top); 1723 rx_ring->rx_skb_top = NULL; 1724 } 1725 1726 /* Zero out the descriptor ring */ 1727 memset(rx_ring->desc, 0, rx_ring->size); 1728 1729 rx_ring->next_to_clean = 0; 1730 rx_ring->next_to_use = 0; 1731 adapter->flags2 &= ~FLAG2_IS_DISCARDING; 1732 } 1733 1734 static void e1000e_downshift_workaround(struct work_struct *work) 1735 { 1736 struct e1000_adapter *adapter = container_of(work, 1737 struct e1000_adapter, 1738 downshift_task); 1739 1740 if (test_bit(__E1000_DOWN, &adapter->state)) 1741 return; 1742 1743 e1000e_gig_downshift_workaround_ich8lan(&adapter->hw); 1744 } 1745 1746 /** 1747 * e1000_intr_msi - Interrupt Handler 1748 * @irq: interrupt number 1749 * @data: pointer to a network interface device structure 1750 **/ 1751 static irqreturn_t e1000_intr_msi(int __always_unused irq, void *data) 1752 { 1753 struct net_device *netdev = data; 1754 struct e1000_adapter *adapter = netdev_priv(netdev); 1755 struct e1000_hw *hw = &adapter->hw; 1756 u32 icr = er32(ICR); 1757 1758 /* read ICR disables interrupts using IAM */ 1759 if (icr & E1000_ICR_LSC) { 1760 hw->mac.get_link_status = true; 1761 /* ICH8 workaround-- Call gig speed drop workaround on cable 1762 * disconnect (LSC) before accessing any PHY registers 1763 */ 1764 if ((adapter->flags & FLAG_LSC_GIG_SPEED_DROP) && 1765 (!(er32(STATUS) & E1000_STATUS_LU))) 1766 schedule_work(&adapter->downshift_task); 1767 1768 /* 80003ES2LAN workaround-- For packet buffer work-around on 1769 * link down event; disable receives here in the ISR and reset 1770 * adapter in watchdog 1771 */ 1772 if (netif_carrier_ok(netdev) && 1773 adapter->flags & FLAG_RX_NEEDS_RESTART) { 1774 /* disable receives */ 1775 u32 rctl = er32(RCTL); 1776 1777 ew32(RCTL, rctl & ~E1000_RCTL_EN); 1778 adapter->flags |= FLAG_RESTART_NOW; 1779 } 1780 /* guard against interrupt when we're going down */ 1781 if (!test_bit(__E1000_DOWN, &adapter->state)) 1782 mod_timer(&adapter->watchdog_timer, jiffies + 1); 1783 } 1784 1785 /* Reset on uncorrectable ECC error */ 1786 if ((icr & E1000_ICR_ECCER) && (hw->mac.type >= e1000_pch_lpt)) { 1787 u32 pbeccsts = er32(PBECCSTS); 1788 1789 adapter->corr_errors += 1790 pbeccsts & E1000_PBECCSTS_CORR_ERR_CNT_MASK; 1791 adapter->uncorr_errors += 1792 (pbeccsts & E1000_PBECCSTS_UNCORR_ERR_CNT_MASK) >> 1793 E1000_PBECCSTS_UNCORR_ERR_CNT_SHIFT; 1794 1795 /* Do the reset outside of interrupt context */ 1796 schedule_work(&adapter->reset_task); 1797 1798 /* return immediately since reset is imminent */ 1799 return IRQ_HANDLED; 1800 } 1801 1802 if (napi_schedule_prep(&adapter->napi)) { 1803 adapter->total_tx_bytes = 0; 1804 adapter->total_tx_packets = 0; 1805 adapter->total_rx_bytes = 0; 1806 adapter->total_rx_packets = 0; 1807 __napi_schedule(&adapter->napi); 1808 } 1809 1810 return IRQ_HANDLED; 1811 } 1812 1813 /** 1814 * e1000_intr - Interrupt Handler 1815 * @irq: interrupt number 1816 * @data: pointer to a network interface device structure 1817 **/ 1818 static irqreturn_t e1000_intr(int __always_unused irq, void *data) 1819 { 1820 struct net_device *netdev = data; 1821 struct e1000_adapter *adapter = netdev_priv(netdev); 1822 struct e1000_hw *hw = &adapter->hw; 1823 u32 rctl, icr = er32(ICR); 1824 1825 if (!icr || test_bit(__E1000_DOWN, &adapter->state)) 1826 return IRQ_NONE; /* Not our interrupt */ 1827 1828 /* IMS will not auto-mask if INT_ASSERTED is not set, and if it is 1829 * not set, then the adapter didn't send an interrupt 1830 */ 1831 if (!(icr & E1000_ICR_INT_ASSERTED)) 1832 return IRQ_NONE; 1833 1834 /* Interrupt Auto-Mask...upon reading ICR, 1835 * interrupts are masked. No need for the 1836 * IMC write 1837 */ 1838 1839 if (icr & E1000_ICR_LSC) { 1840 hw->mac.get_link_status = true; 1841 /* ICH8 workaround-- Call gig speed drop workaround on cable 1842 * disconnect (LSC) before accessing any PHY registers 1843 */ 1844 if ((adapter->flags & FLAG_LSC_GIG_SPEED_DROP) && 1845 (!(er32(STATUS) & E1000_STATUS_LU))) 1846 schedule_work(&adapter->downshift_task); 1847 1848 /* 80003ES2LAN workaround-- 1849 * For packet buffer work-around on link down event; 1850 * disable receives here in the ISR and 1851 * reset adapter in watchdog 1852 */ 1853 if (netif_carrier_ok(netdev) && 1854 (adapter->flags & FLAG_RX_NEEDS_RESTART)) { 1855 /* disable receives */ 1856 rctl = er32(RCTL); 1857 ew32(RCTL, rctl & ~E1000_RCTL_EN); 1858 adapter->flags |= FLAG_RESTART_NOW; 1859 } 1860 /* guard against interrupt when we're going down */ 1861 if (!test_bit(__E1000_DOWN, &adapter->state)) 1862 mod_timer(&adapter->watchdog_timer, jiffies + 1); 1863 } 1864 1865 /* Reset on uncorrectable ECC error */ 1866 if ((icr & E1000_ICR_ECCER) && (hw->mac.type >= e1000_pch_lpt)) { 1867 u32 pbeccsts = er32(PBECCSTS); 1868 1869 adapter->corr_errors += 1870 pbeccsts & E1000_PBECCSTS_CORR_ERR_CNT_MASK; 1871 adapter->uncorr_errors += 1872 (pbeccsts & E1000_PBECCSTS_UNCORR_ERR_CNT_MASK) >> 1873 E1000_PBECCSTS_UNCORR_ERR_CNT_SHIFT; 1874 1875 /* Do the reset outside of interrupt context */ 1876 schedule_work(&adapter->reset_task); 1877 1878 /* return immediately since reset is imminent */ 1879 return IRQ_HANDLED; 1880 } 1881 1882 if (napi_schedule_prep(&adapter->napi)) { 1883 adapter->total_tx_bytes = 0; 1884 adapter->total_tx_packets = 0; 1885 adapter->total_rx_bytes = 0; 1886 adapter->total_rx_packets = 0; 1887 __napi_schedule(&adapter->napi); 1888 } 1889 1890 return IRQ_HANDLED; 1891 } 1892 1893 static irqreturn_t e1000_msix_other(int __always_unused irq, void *data) 1894 { 1895 struct net_device *netdev = data; 1896 struct e1000_adapter *adapter = netdev_priv(netdev); 1897 struct e1000_hw *hw = &adapter->hw; 1898 u32 icr = er32(ICR); 1899 1900 if (icr & adapter->eiac_mask) 1901 ew32(ICS, (icr & adapter->eiac_mask)); 1902 1903 if (icr & E1000_ICR_LSC) { 1904 hw->mac.get_link_status = true; 1905 /* guard against interrupt when we're going down */ 1906 if (!test_bit(__E1000_DOWN, &adapter->state)) 1907 mod_timer(&adapter->watchdog_timer, jiffies + 1); 1908 } 1909 1910 if (!test_bit(__E1000_DOWN, &adapter->state)) 1911 ew32(IMS, E1000_IMS_OTHER | IMS_OTHER_MASK); 1912 1913 return IRQ_HANDLED; 1914 } 1915 1916 static irqreturn_t e1000_intr_msix_tx(int __always_unused irq, void *data) 1917 { 1918 struct net_device *netdev = data; 1919 struct e1000_adapter *adapter = netdev_priv(netdev); 1920 struct e1000_hw *hw = &adapter->hw; 1921 struct e1000_ring *tx_ring = adapter->tx_ring; 1922 1923 adapter->total_tx_bytes = 0; 1924 adapter->total_tx_packets = 0; 1925 1926 if (!e1000_clean_tx_irq(tx_ring)) 1927 /* Ring was not completely cleaned, so fire another interrupt */ 1928 ew32(ICS, tx_ring->ims_val); 1929 1930 if (!test_bit(__E1000_DOWN, &adapter->state)) 1931 ew32(IMS, adapter->tx_ring->ims_val); 1932 1933 return IRQ_HANDLED; 1934 } 1935 1936 static irqreturn_t e1000_intr_msix_rx(int __always_unused irq, void *data) 1937 { 1938 struct net_device *netdev = data; 1939 struct e1000_adapter *adapter = netdev_priv(netdev); 1940 struct e1000_ring *rx_ring = adapter->rx_ring; 1941 1942 /* Write the ITR value calculated at the end of the 1943 * previous interrupt. 1944 */ 1945 if (rx_ring->set_itr) { 1946 u32 itr = rx_ring->itr_val ? 1947 1000000000 / (rx_ring->itr_val * 256) : 0; 1948 1949 writel(itr, rx_ring->itr_register); 1950 rx_ring->set_itr = 0; 1951 } 1952 1953 if (napi_schedule_prep(&adapter->napi)) { 1954 adapter->total_rx_bytes = 0; 1955 adapter->total_rx_packets = 0; 1956 __napi_schedule(&adapter->napi); 1957 } 1958 return IRQ_HANDLED; 1959 } 1960 1961 /** 1962 * e1000_configure_msix - Configure MSI-X hardware 1963 * @adapter: board private structure 1964 * 1965 * e1000_configure_msix sets up the hardware to properly 1966 * generate MSI-X interrupts. 1967 **/ 1968 static void e1000_configure_msix(struct e1000_adapter *adapter) 1969 { 1970 struct e1000_hw *hw = &adapter->hw; 1971 struct e1000_ring *rx_ring = adapter->rx_ring; 1972 struct e1000_ring *tx_ring = adapter->tx_ring; 1973 int vector = 0; 1974 u32 ctrl_ext, ivar = 0; 1975 1976 adapter->eiac_mask = 0; 1977 1978 /* Workaround issue with spurious interrupts on 82574 in MSI-X mode */ 1979 if (hw->mac.type == e1000_82574) { 1980 u32 rfctl = er32(RFCTL); 1981 1982 rfctl |= E1000_RFCTL_ACK_DIS; 1983 ew32(RFCTL, rfctl); 1984 } 1985 1986 /* Configure Rx vector */ 1987 rx_ring->ims_val = E1000_IMS_RXQ0; 1988 adapter->eiac_mask |= rx_ring->ims_val; 1989 if (rx_ring->itr_val) 1990 writel(1000000000 / (rx_ring->itr_val * 256), 1991 rx_ring->itr_register); 1992 else 1993 writel(1, rx_ring->itr_register); 1994 ivar = E1000_IVAR_INT_ALLOC_VALID | vector; 1995 1996 /* Configure Tx vector */ 1997 tx_ring->ims_val = E1000_IMS_TXQ0; 1998 vector++; 1999 if (tx_ring->itr_val) 2000 writel(1000000000 / (tx_ring->itr_val * 256), 2001 tx_ring->itr_register); 2002 else 2003 writel(1, tx_ring->itr_register); 2004 adapter->eiac_mask |= tx_ring->ims_val; 2005 ivar |= ((E1000_IVAR_INT_ALLOC_VALID | vector) << 8); 2006 2007 /* set vector for Other Causes, e.g. link changes */ 2008 vector++; 2009 ivar |= ((E1000_IVAR_INT_ALLOC_VALID | vector) << 16); 2010 if (rx_ring->itr_val) 2011 writel(1000000000 / (rx_ring->itr_val * 256), 2012 hw->hw_addr + E1000_EITR_82574(vector)); 2013 else 2014 writel(1, hw->hw_addr + E1000_EITR_82574(vector)); 2015 2016 /* Cause Tx interrupts on every write back */ 2017 ivar |= BIT(31); 2018 2019 ew32(IVAR, ivar); 2020 2021 /* enable MSI-X PBA support */ 2022 ctrl_ext = er32(CTRL_EXT) & ~E1000_CTRL_EXT_IAME; 2023 ctrl_ext |= E1000_CTRL_EXT_PBA_CLR | E1000_CTRL_EXT_EIAME; 2024 ew32(CTRL_EXT, ctrl_ext); 2025 e1e_flush(); 2026 } 2027 2028 void e1000e_reset_interrupt_capability(struct e1000_adapter *adapter) 2029 { 2030 if (adapter->msix_entries) { 2031 pci_disable_msix(adapter->pdev); 2032 kfree(adapter->msix_entries); 2033 adapter->msix_entries = NULL; 2034 } else if (adapter->flags & FLAG_MSI_ENABLED) { 2035 pci_disable_msi(adapter->pdev); 2036 adapter->flags &= ~FLAG_MSI_ENABLED; 2037 } 2038 } 2039 2040 /** 2041 * e1000e_set_interrupt_capability - set MSI or MSI-X if supported 2042 * @adapter: board private structure 2043 * 2044 * Attempt to configure interrupts using the best available 2045 * capabilities of the hardware and kernel. 2046 **/ 2047 void e1000e_set_interrupt_capability(struct e1000_adapter *adapter) 2048 { 2049 int err; 2050 int i; 2051 2052 switch (adapter->int_mode) { 2053 case E1000E_INT_MODE_MSIX: 2054 if (adapter->flags & FLAG_HAS_MSIX) { 2055 adapter->num_vectors = 3; /* RxQ0, TxQ0 and other */ 2056 adapter->msix_entries = kcalloc(adapter->num_vectors, 2057 sizeof(struct 2058 msix_entry), 2059 GFP_KERNEL); 2060 if (adapter->msix_entries) { 2061 struct e1000_adapter *a = adapter; 2062 2063 for (i = 0; i < adapter->num_vectors; i++) 2064 adapter->msix_entries[i].entry = i; 2065 2066 err = pci_enable_msix_range(a->pdev, 2067 a->msix_entries, 2068 a->num_vectors, 2069 a->num_vectors); 2070 if (err > 0) 2071 return; 2072 } 2073 /* MSI-X failed, so fall through and try MSI */ 2074 e_err("Failed to initialize MSI-X interrupts. Falling back to MSI interrupts.\n"); 2075 e1000e_reset_interrupt_capability(adapter); 2076 } 2077 adapter->int_mode = E1000E_INT_MODE_MSI; 2078 fallthrough; 2079 case E1000E_INT_MODE_MSI: 2080 if (!pci_enable_msi(adapter->pdev)) { 2081 adapter->flags |= FLAG_MSI_ENABLED; 2082 } else { 2083 adapter->int_mode = E1000E_INT_MODE_LEGACY; 2084 e_err("Failed to initialize MSI interrupts. Falling back to legacy interrupts.\n"); 2085 } 2086 fallthrough; 2087 case E1000E_INT_MODE_LEGACY: 2088 /* Don't do anything; this is the system default */ 2089 break; 2090 } 2091 2092 /* store the number of vectors being used */ 2093 adapter->num_vectors = 1; 2094 } 2095 2096 /** 2097 * e1000_request_msix - Initialize MSI-X interrupts 2098 * @adapter: board private structure 2099 * 2100 * e1000_request_msix allocates MSI-X vectors and requests interrupts from the 2101 * kernel. 2102 **/ 2103 static int e1000_request_msix(struct e1000_adapter *adapter) 2104 { 2105 struct net_device *netdev = adapter->netdev; 2106 int err = 0, vector = 0; 2107 2108 if (strlen(netdev->name) < (IFNAMSIZ - 5)) 2109 snprintf(adapter->rx_ring->name, 2110 sizeof(adapter->rx_ring->name) - 1, 2111 "%.14s-rx-0", netdev->name); 2112 else 2113 memcpy(adapter->rx_ring->name, netdev->name, IFNAMSIZ); 2114 err = request_irq(adapter->msix_entries[vector].vector, 2115 e1000_intr_msix_rx, 0, adapter->rx_ring->name, 2116 netdev); 2117 if (err) 2118 return err; 2119 adapter->rx_ring->itr_register = adapter->hw.hw_addr + 2120 E1000_EITR_82574(vector); 2121 adapter->rx_ring->itr_val = adapter->itr; 2122 vector++; 2123 2124 if (strlen(netdev->name) < (IFNAMSIZ - 5)) 2125 snprintf(adapter->tx_ring->name, 2126 sizeof(adapter->tx_ring->name) - 1, 2127 "%.14s-tx-0", netdev->name); 2128 else 2129 memcpy(adapter->tx_ring->name, netdev->name, IFNAMSIZ); 2130 err = request_irq(adapter->msix_entries[vector].vector, 2131 e1000_intr_msix_tx, 0, adapter->tx_ring->name, 2132 netdev); 2133 if (err) 2134 return err; 2135 adapter->tx_ring->itr_register = adapter->hw.hw_addr + 2136 E1000_EITR_82574(vector); 2137 adapter->tx_ring->itr_val = adapter->itr; 2138 vector++; 2139 2140 err = request_irq(adapter->msix_entries[vector].vector, 2141 e1000_msix_other, 0, netdev->name, netdev); 2142 if (err) 2143 return err; 2144 2145 e1000_configure_msix(adapter); 2146 2147 return 0; 2148 } 2149 2150 /** 2151 * e1000_request_irq - initialize interrupts 2152 * @adapter: board private structure 2153 * 2154 * Attempts to configure interrupts using the best available 2155 * capabilities of the hardware and kernel. 2156 **/ 2157 static int e1000_request_irq(struct e1000_adapter *adapter) 2158 { 2159 struct net_device *netdev = adapter->netdev; 2160 int err; 2161 2162 if (adapter->msix_entries) { 2163 err = e1000_request_msix(adapter); 2164 if (!err) 2165 return err; 2166 /* fall back to MSI */ 2167 e1000e_reset_interrupt_capability(adapter); 2168 adapter->int_mode = E1000E_INT_MODE_MSI; 2169 e1000e_set_interrupt_capability(adapter); 2170 } 2171 if (adapter->flags & FLAG_MSI_ENABLED) { 2172 err = request_irq(adapter->pdev->irq, e1000_intr_msi, 0, 2173 netdev->name, netdev); 2174 if (!err) 2175 return err; 2176 2177 /* fall back to legacy interrupt */ 2178 e1000e_reset_interrupt_capability(adapter); 2179 adapter->int_mode = E1000E_INT_MODE_LEGACY; 2180 } 2181 2182 err = request_irq(adapter->pdev->irq, e1000_intr, IRQF_SHARED, 2183 netdev->name, netdev); 2184 if (err) 2185 e_err("Unable to allocate interrupt, Error: %d\n", err); 2186 2187 return err; 2188 } 2189 2190 static void e1000_free_irq(struct e1000_adapter *adapter) 2191 { 2192 struct net_device *netdev = adapter->netdev; 2193 2194 if (adapter->msix_entries) { 2195 int vector = 0; 2196 2197 free_irq(adapter->msix_entries[vector].vector, netdev); 2198 vector++; 2199 2200 free_irq(adapter->msix_entries[vector].vector, netdev); 2201 vector++; 2202 2203 /* Other Causes interrupt vector */ 2204 free_irq(adapter->msix_entries[vector].vector, netdev); 2205 return; 2206 } 2207 2208 free_irq(adapter->pdev->irq, netdev); 2209 } 2210 2211 /** 2212 * e1000_irq_disable - Mask off interrupt generation on the NIC 2213 * @adapter: board private structure 2214 **/ 2215 static void e1000_irq_disable(struct e1000_adapter *adapter) 2216 { 2217 struct e1000_hw *hw = &adapter->hw; 2218 2219 ew32(IMC, ~0); 2220 if (adapter->msix_entries) 2221 ew32(EIAC_82574, 0); 2222 e1e_flush(); 2223 2224 if (adapter->msix_entries) { 2225 int i; 2226 2227 for (i = 0; i < adapter->num_vectors; i++) 2228 synchronize_irq(adapter->msix_entries[i].vector); 2229 } else { 2230 synchronize_irq(adapter->pdev->irq); 2231 } 2232 } 2233 2234 /** 2235 * e1000_irq_enable - Enable default interrupt generation settings 2236 * @adapter: board private structure 2237 **/ 2238 static void e1000_irq_enable(struct e1000_adapter *adapter) 2239 { 2240 struct e1000_hw *hw = &adapter->hw; 2241 2242 if (adapter->msix_entries) { 2243 ew32(EIAC_82574, adapter->eiac_mask & E1000_EIAC_MASK_82574); 2244 ew32(IMS, adapter->eiac_mask | E1000_IMS_OTHER | 2245 IMS_OTHER_MASK); 2246 } else if (hw->mac.type >= e1000_pch_lpt) { 2247 ew32(IMS, IMS_ENABLE_MASK | E1000_IMS_ECCER); 2248 } else { 2249 ew32(IMS, IMS_ENABLE_MASK); 2250 } 2251 e1e_flush(); 2252 } 2253 2254 /** 2255 * e1000e_get_hw_control - get control of the h/w from f/w 2256 * @adapter: address of board private structure 2257 * 2258 * e1000e_get_hw_control sets {CTRL_EXT|SWSM}:DRV_LOAD bit. 2259 * For ASF and Pass Through versions of f/w this means that 2260 * the driver is loaded. For AMT version (only with 82573) 2261 * of the f/w this means that the network i/f is open. 2262 **/ 2263 void e1000e_get_hw_control(struct e1000_adapter *adapter) 2264 { 2265 struct e1000_hw *hw = &adapter->hw; 2266 u32 ctrl_ext; 2267 u32 swsm; 2268 2269 /* Let firmware know the driver has taken over */ 2270 if (adapter->flags & FLAG_HAS_SWSM_ON_LOAD) { 2271 swsm = er32(SWSM); 2272 ew32(SWSM, swsm | E1000_SWSM_DRV_LOAD); 2273 } else if (adapter->flags & FLAG_HAS_CTRLEXT_ON_LOAD) { 2274 ctrl_ext = er32(CTRL_EXT); 2275 ew32(CTRL_EXT, ctrl_ext | E1000_CTRL_EXT_DRV_LOAD); 2276 } 2277 } 2278 2279 /** 2280 * e1000e_release_hw_control - release control of the h/w to f/w 2281 * @adapter: address of board private structure 2282 * 2283 * e1000e_release_hw_control resets {CTRL_EXT|SWSM}:DRV_LOAD bit. 2284 * For ASF and Pass Through versions of f/w this means that the 2285 * driver is no longer loaded. For AMT version (only with 82573) i 2286 * of the f/w this means that the network i/f is closed. 2287 * 2288 **/ 2289 void e1000e_release_hw_control(struct e1000_adapter *adapter) 2290 { 2291 struct e1000_hw *hw = &adapter->hw; 2292 u32 ctrl_ext; 2293 u32 swsm; 2294 2295 /* Let firmware taken over control of h/w */ 2296 if (adapter->flags & FLAG_HAS_SWSM_ON_LOAD) { 2297 swsm = er32(SWSM); 2298 ew32(SWSM, swsm & ~E1000_SWSM_DRV_LOAD); 2299 } else if (adapter->flags & FLAG_HAS_CTRLEXT_ON_LOAD) { 2300 ctrl_ext = er32(CTRL_EXT); 2301 ew32(CTRL_EXT, ctrl_ext & ~E1000_CTRL_EXT_DRV_LOAD); 2302 } 2303 } 2304 2305 /** 2306 * e1000_alloc_ring_dma - allocate memory for a ring structure 2307 * @adapter: board private structure 2308 * @ring: ring struct for which to allocate dma 2309 **/ 2310 static int e1000_alloc_ring_dma(struct e1000_adapter *adapter, 2311 struct e1000_ring *ring) 2312 { 2313 struct pci_dev *pdev = adapter->pdev; 2314 2315 ring->desc = dma_alloc_coherent(&pdev->dev, ring->size, &ring->dma, 2316 GFP_KERNEL); 2317 if (!ring->desc) 2318 return -ENOMEM; 2319 2320 return 0; 2321 } 2322 2323 /** 2324 * e1000e_setup_tx_resources - allocate Tx resources (Descriptors) 2325 * @tx_ring: Tx descriptor ring 2326 * 2327 * Return 0 on success, negative on failure 2328 **/ 2329 int e1000e_setup_tx_resources(struct e1000_ring *tx_ring) 2330 { 2331 struct e1000_adapter *adapter = tx_ring->adapter; 2332 int err = -ENOMEM, size; 2333 2334 size = sizeof(struct e1000_buffer) * tx_ring->count; 2335 tx_ring->buffer_info = vzalloc(size); 2336 if (!tx_ring->buffer_info) 2337 goto err; 2338 2339 /* round up to nearest 4K */ 2340 tx_ring->size = tx_ring->count * sizeof(struct e1000_tx_desc); 2341 tx_ring->size = ALIGN(tx_ring->size, 4096); 2342 2343 err = e1000_alloc_ring_dma(adapter, tx_ring); 2344 if (err) 2345 goto err; 2346 2347 tx_ring->next_to_use = 0; 2348 tx_ring->next_to_clean = 0; 2349 2350 return 0; 2351 err: 2352 vfree(tx_ring->buffer_info); 2353 e_err("Unable to allocate memory for the transmit descriptor ring\n"); 2354 return err; 2355 } 2356 2357 /** 2358 * e1000e_setup_rx_resources - allocate Rx resources (Descriptors) 2359 * @rx_ring: Rx descriptor ring 2360 * 2361 * Returns 0 on success, negative on failure 2362 **/ 2363 int e1000e_setup_rx_resources(struct e1000_ring *rx_ring) 2364 { 2365 struct e1000_adapter *adapter = rx_ring->adapter; 2366 struct e1000_buffer *buffer_info; 2367 int i, size, desc_len, err = -ENOMEM; 2368 2369 size = sizeof(struct e1000_buffer) * rx_ring->count; 2370 rx_ring->buffer_info = vzalloc(size); 2371 if (!rx_ring->buffer_info) 2372 goto err; 2373 2374 for (i = 0; i < rx_ring->count; i++) { 2375 buffer_info = &rx_ring->buffer_info[i]; 2376 buffer_info->ps_pages = kcalloc(PS_PAGE_BUFFERS, 2377 sizeof(struct e1000_ps_page), 2378 GFP_KERNEL); 2379 if (!buffer_info->ps_pages) 2380 goto err_pages; 2381 } 2382 2383 desc_len = sizeof(union e1000_rx_desc_packet_split); 2384 2385 /* Round up to nearest 4K */ 2386 rx_ring->size = rx_ring->count * desc_len; 2387 rx_ring->size = ALIGN(rx_ring->size, 4096); 2388 2389 err = e1000_alloc_ring_dma(adapter, rx_ring); 2390 if (err) 2391 goto err_pages; 2392 2393 rx_ring->next_to_clean = 0; 2394 rx_ring->next_to_use = 0; 2395 rx_ring->rx_skb_top = NULL; 2396 2397 return 0; 2398 2399 err_pages: 2400 for (i = 0; i < rx_ring->count; i++) { 2401 buffer_info = &rx_ring->buffer_info[i]; 2402 kfree(buffer_info->ps_pages); 2403 } 2404 err: 2405 vfree(rx_ring->buffer_info); 2406 e_err("Unable to allocate memory for the receive descriptor ring\n"); 2407 return err; 2408 } 2409 2410 /** 2411 * e1000_clean_tx_ring - Free Tx Buffers 2412 * @tx_ring: Tx descriptor ring 2413 **/ 2414 static void e1000_clean_tx_ring(struct e1000_ring *tx_ring) 2415 { 2416 struct e1000_adapter *adapter = tx_ring->adapter; 2417 struct e1000_buffer *buffer_info; 2418 unsigned long size; 2419 unsigned int i; 2420 2421 for (i = 0; i < tx_ring->count; i++) { 2422 buffer_info = &tx_ring->buffer_info[i]; 2423 e1000_put_txbuf(tx_ring, buffer_info, false); 2424 } 2425 2426 netdev_reset_queue(adapter->netdev); 2427 size = sizeof(struct e1000_buffer) * tx_ring->count; 2428 memset(tx_ring->buffer_info, 0, size); 2429 2430 memset(tx_ring->desc, 0, tx_ring->size); 2431 2432 tx_ring->next_to_use = 0; 2433 tx_ring->next_to_clean = 0; 2434 } 2435 2436 /** 2437 * e1000e_free_tx_resources - Free Tx Resources per Queue 2438 * @tx_ring: Tx descriptor ring 2439 * 2440 * Free all transmit software resources 2441 **/ 2442 void e1000e_free_tx_resources(struct e1000_ring *tx_ring) 2443 { 2444 struct e1000_adapter *adapter = tx_ring->adapter; 2445 struct pci_dev *pdev = adapter->pdev; 2446 2447 e1000_clean_tx_ring(tx_ring); 2448 2449 vfree(tx_ring->buffer_info); 2450 tx_ring->buffer_info = NULL; 2451 2452 dma_free_coherent(&pdev->dev, tx_ring->size, tx_ring->desc, 2453 tx_ring->dma); 2454 tx_ring->desc = NULL; 2455 } 2456 2457 /** 2458 * e1000e_free_rx_resources - Free Rx Resources 2459 * @rx_ring: Rx descriptor ring 2460 * 2461 * Free all receive software resources 2462 **/ 2463 void e1000e_free_rx_resources(struct e1000_ring *rx_ring) 2464 { 2465 struct e1000_adapter *adapter = rx_ring->adapter; 2466 struct pci_dev *pdev = adapter->pdev; 2467 int i; 2468 2469 e1000_clean_rx_ring(rx_ring); 2470 2471 for (i = 0; i < rx_ring->count; i++) 2472 kfree(rx_ring->buffer_info[i].ps_pages); 2473 2474 vfree(rx_ring->buffer_info); 2475 rx_ring->buffer_info = NULL; 2476 2477 dma_free_coherent(&pdev->dev, rx_ring->size, rx_ring->desc, 2478 rx_ring->dma); 2479 rx_ring->desc = NULL; 2480 } 2481 2482 /** 2483 * e1000_update_itr - update the dynamic ITR value based on statistics 2484 * @itr_setting: current adapter->itr 2485 * @packets: the number of packets during this measurement interval 2486 * @bytes: the number of bytes during this measurement interval 2487 * 2488 * Stores a new ITR value based on packets and byte 2489 * counts during the last interrupt. The advantage of per interrupt 2490 * computation is faster updates and more accurate ITR for the current 2491 * traffic pattern. Constants in this function were computed 2492 * based on theoretical maximum wire speed and thresholds were set based 2493 * on testing data as well as attempting to minimize response time 2494 * while increasing bulk throughput. This functionality is controlled 2495 * by the InterruptThrottleRate module parameter. 2496 **/ 2497 static unsigned int e1000_update_itr(u16 itr_setting, int packets, int bytes) 2498 { 2499 unsigned int retval = itr_setting; 2500 2501 if (packets == 0) 2502 return itr_setting; 2503 2504 switch (itr_setting) { 2505 case lowest_latency: 2506 /* handle TSO and jumbo frames */ 2507 if (bytes / packets > 8000) 2508 retval = bulk_latency; 2509 else if ((packets < 5) && (bytes > 512)) 2510 retval = low_latency; 2511 break; 2512 case low_latency: /* 50 usec aka 20000 ints/s */ 2513 if (bytes > 10000) { 2514 /* this if handles the TSO accounting */ 2515 if (bytes / packets > 8000) 2516 retval = bulk_latency; 2517 else if ((packets < 10) || ((bytes / packets) > 1200)) 2518 retval = bulk_latency; 2519 else if ((packets > 35)) 2520 retval = lowest_latency; 2521 } else if (bytes / packets > 2000) { 2522 retval = bulk_latency; 2523 } else if (packets <= 2 && bytes < 512) { 2524 retval = lowest_latency; 2525 } 2526 break; 2527 case bulk_latency: /* 250 usec aka 4000 ints/s */ 2528 if (bytes > 25000) { 2529 if (packets > 35) 2530 retval = low_latency; 2531 } else if (bytes < 6000) { 2532 retval = low_latency; 2533 } 2534 break; 2535 } 2536 2537 return retval; 2538 } 2539 2540 static void e1000_set_itr(struct e1000_adapter *adapter) 2541 { 2542 u16 current_itr; 2543 u32 new_itr = adapter->itr; 2544 2545 /* for non-gigabit speeds, just fix the interrupt rate at 4000 */ 2546 if (adapter->link_speed != SPEED_1000) { 2547 new_itr = 4000; 2548 goto set_itr_now; 2549 } 2550 2551 if (adapter->flags2 & FLAG2_DISABLE_AIM) { 2552 new_itr = 0; 2553 goto set_itr_now; 2554 } 2555 2556 adapter->tx_itr = e1000_update_itr(adapter->tx_itr, 2557 adapter->total_tx_packets, 2558 adapter->total_tx_bytes); 2559 /* conservative mode (itr 3) eliminates the lowest_latency setting */ 2560 if (adapter->itr_setting == 3 && adapter->tx_itr == lowest_latency) 2561 adapter->tx_itr = low_latency; 2562 2563 adapter->rx_itr = e1000_update_itr(adapter->rx_itr, 2564 adapter->total_rx_packets, 2565 adapter->total_rx_bytes); 2566 /* conservative mode (itr 3) eliminates the lowest_latency setting */ 2567 if (adapter->itr_setting == 3 && adapter->rx_itr == lowest_latency) 2568 adapter->rx_itr = low_latency; 2569 2570 current_itr = max(adapter->rx_itr, adapter->tx_itr); 2571 2572 /* counts and packets in update_itr are dependent on these numbers */ 2573 switch (current_itr) { 2574 case lowest_latency: 2575 new_itr = 70000; 2576 break; 2577 case low_latency: 2578 new_itr = 20000; /* aka hwitr = ~200 */ 2579 break; 2580 case bulk_latency: 2581 new_itr = 4000; 2582 break; 2583 default: 2584 break; 2585 } 2586 2587 set_itr_now: 2588 if (new_itr != adapter->itr) { 2589 /* this attempts to bias the interrupt rate towards Bulk 2590 * by adding intermediate steps when interrupt rate is 2591 * increasing 2592 */ 2593 new_itr = new_itr > adapter->itr ? 2594 min(adapter->itr + (new_itr >> 2), new_itr) : new_itr; 2595 adapter->itr = new_itr; 2596 adapter->rx_ring->itr_val = new_itr; 2597 if (adapter->msix_entries) 2598 adapter->rx_ring->set_itr = 1; 2599 else 2600 e1000e_write_itr(adapter, new_itr); 2601 } 2602 } 2603 2604 /** 2605 * e1000e_write_itr - write the ITR value to the appropriate registers 2606 * @adapter: address of board private structure 2607 * @itr: new ITR value to program 2608 * 2609 * e1000e_write_itr determines if the adapter is in MSI-X mode 2610 * and, if so, writes the EITR registers with the ITR value. 2611 * Otherwise, it writes the ITR value into the ITR register. 2612 **/ 2613 void e1000e_write_itr(struct e1000_adapter *adapter, u32 itr) 2614 { 2615 struct e1000_hw *hw = &adapter->hw; 2616 u32 new_itr = itr ? 1000000000 / (itr * 256) : 0; 2617 2618 if (adapter->msix_entries) { 2619 int vector; 2620 2621 for (vector = 0; vector < adapter->num_vectors; vector++) 2622 writel(new_itr, hw->hw_addr + E1000_EITR_82574(vector)); 2623 } else { 2624 ew32(ITR, new_itr); 2625 } 2626 } 2627 2628 /** 2629 * e1000_alloc_queues - Allocate memory for all rings 2630 * @adapter: board private structure to initialize 2631 **/ 2632 static int e1000_alloc_queues(struct e1000_adapter *adapter) 2633 { 2634 int size = sizeof(struct e1000_ring); 2635 2636 adapter->tx_ring = kzalloc(size, GFP_KERNEL); 2637 if (!adapter->tx_ring) 2638 goto err; 2639 adapter->tx_ring->count = adapter->tx_ring_count; 2640 adapter->tx_ring->adapter = adapter; 2641 2642 adapter->rx_ring = kzalloc(size, GFP_KERNEL); 2643 if (!adapter->rx_ring) 2644 goto err; 2645 adapter->rx_ring->count = adapter->rx_ring_count; 2646 adapter->rx_ring->adapter = adapter; 2647 2648 return 0; 2649 err: 2650 e_err("Unable to allocate memory for queues\n"); 2651 kfree(adapter->rx_ring); 2652 kfree(adapter->tx_ring); 2653 return -ENOMEM; 2654 } 2655 2656 /** 2657 * e1000e_poll - NAPI Rx polling callback 2658 * @napi: struct associated with this polling callback 2659 * @budget: number of packets driver is allowed to process this poll 2660 **/ 2661 static int e1000e_poll(struct napi_struct *napi, int budget) 2662 { 2663 struct e1000_adapter *adapter = container_of(napi, struct e1000_adapter, 2664 napi); 2665 struct e1000_hw *hw = &adapter->hw; 2666 struct net_device *poll_dev = adapter->netdev; 2667 int tx_cleaned = 1, work_done = 0; 2668 2669 adapter = netdev_priv(poll_dev); 2670 2671 if (!adapter->msix_entries || 2672 (adapter->rx_ring->ims_val & adapter->tx_ring->ims_val)) 2673 tx_cleaned = e1000_clean_tx_irq(adapter->tx_ring); 2674 2675 adapter->clean_rx(adapter->rx_ring, &work_done, budget); 2676 2677 if (!tx_cleaned || work_done == budget) 2678 return budget; 2679 2680 /* Exit the polling mode, but don't re-enable interrupts if stack might 2681 * poll us due to busy-polling 2682 */ 2683 if (likely(napi_complete_done(napi, work_done))) { 2684 if (adapter->itr_setting & 3) 2685 e1000_set_itr(adapter); 2686 if (!test_bit(__E1000_DOWN, &adapter->state)) { 2687 if (adapter->msix_entries) 2688 ew32(IMS, adapter->rx_ring->ims_val); 2689 else 2690 e1000_irq_enable(adapter); 2691 } 2692 } 2693 2694 return work_done; 2695 } 2696 2697 static int e1000_vlan_rx_add_vid(struct net_device *netdev, 2698 __always_unused __be16 proto, u16 vid) 2699 { 2700 struct e1000_adapter *adapter = netdev_priv(netdev); 2701 struct e1000_hw *hw = &adapter->hw; 2702 u32 vfta, index; 2703 2704 /* don't update vlan cookie if already programmed */ 2705 if ((adapter->hw.mng_cookie.status & 2706 E1000_MNG_DHCP_COOKIE_STATUS_VLAN) && 2707 (vid == adapter->mng_vlan_id)) 2708 return 0; 2709 2710 /* add VID to filter table */ 2711 if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) { 2712 index = (vid >> 5) & 0x7F; 2713 vfta = E1000_READ_REG_ARRAY(hw, E1000_VFTA, index); 2714 vfta |= BIT((vid & 0x1F)); 2715 hw->mac.ops.write_vfta(hw, index, vfta); 2716 } 2717 2718 set_bit(vid, adapter->active_vlans); 2719 2720 return 0; 2721 } 2722 2723 static int e1000_vlan_rx_kill_vid(struct net_device *netdev, 2724 __always_unused __be16 proto, u16 vid) 2725 { 2726 struct e1000_adapter *adapter = netdev_priv(netdev); 2727 struct e1000_hw *hw = &adapter->hw; 2728 u32 vfta, index; 2729 2730 if ((adapter->hw.mng_cookie.status & 2731 E1000_MNG_DHCP_COOKIE_STATUS_VLAN) && 2732 (vid == adapter->mng_vlan_id)) { 2733 /* release control to f/w */ 2734 e1000e_release_hw_control(adapter); 2735 return 0; 2736 } 2737 2738 /* remove VID from filter table */ 2739 if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) { 2740 index = (vid >> 5) & 0x7F; 2741 vfta = E1000_READ_REG_ARRAY(hw, E1000_VFTA, index); 2742 vfta &= ~BIT((vid & 0x1F)); 2743 hw->mac.ops.write_vfta(hw, index, vfta); 2744 } 2745 2746 clear_bit(vid, adapter->active_vlans); 2747 2748 return 0; 2749 } 2750 2751 /** 2752 * e1000e_vlan_filter_disable - helper to disable hw VLAN filtering 2753 * @adapter: board private structure to initialize 2754 **/ 2755 static void e1000e_vlan_filter_disable(struct e1000_adapter *adapter) 2756 { 2757 struct net_device *netdev = adapter->netdev; 2758 struct e1000_hw *hw = &adapter->hw; 2759 u32 rctl; 2760 2761 if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) { 2762 /* disable VLAN receive filtering */ 2763 rctl = er32(RCTL); 2764 rctl &= ~(E1000_RCTL_VFE | E1000_RCTL_CFIEN); 2765 ew32(RCTL, rctl); 2766 2767 if (adapter->mng_vlan_id != (u16)E1000_MNG_VLAN_NONE) { 2768 e1000_vlan_rx_kill_vid(netdev, htons(ETH_P_8021Q), 2769 adapter->mng_vlan_id); 2770 adapter->mng_vlan_id = E1000_MNG_VLAN_NONE; 2771 } 2772 } 2773 } 2774 2775 /** 2776 * e1000e_vlan_filter_enable - helper to enable HW VLAN filtering 2777 * @adapter: board private structure to initialize 2778 **/ 2779 static void e1000e_vlan_filter_enable(struct e1000_adapter *adapter) 2780 { 2781 struct e1000_hw *hw = &adapter->hw; 2782 u32 rctl; 2783 2784 if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) { 2785 /* enable VLAN receive filtering */ 2786 rctl = er32(RCTL); 2787 rctl |= E1000_RCTL_VFE; 2788 rctl &= ~E1000_RCTL_CFIEN; 2789 ew32(RCTL, rctl); 2790 } 2791 } 2792 2793 /** 2794 * e1000e_vlan_strip_disable - helper to disable HW VLAN stripping 2795 * @adapter: board private structure to initialize 2796 **/ 2797 static void e1000e_vlan_strip_disable(struct e1000_adapter *adapter) 2798 { 2799 struct e1000_hw *hw = &adapter->hw; 2800 u32 ctrl; 2801 2802 /* disable VLAN tag insert/strip */ 2803 ctrl = er32(CTRL); 2804 ctrl &= ~E1000_CTRL_VME; 2805 ew32(CTRL, ctrl); 2806 } 2807 2808 /** 2809 * e1000e_vlan_strip_enable - helper to enable HW VLAN stripping 2810 * @adapter: board private structure to initialize 2811 **/ 2812 static void e1000e_vlan_strip_enable(struct e1000_adapter *adapter) 2813 { 2814 struct e1000_hw *hw = &adapter->hw; 2815 u32 ctrl; 2816 2817 /* enable VLAN tag insert/strip */ 2818 ctrl = er32(CTRL); 2819 ctrl |= E1000_CTRL_VME; 2820 ew32(CTRL, ctrl); 2821 } 2822 2823 static void e1000_update_mng_vlan(struct e1000_adapter *adapter) 2824 { 2825 struct net_device *netdev = adapter->netdev; 2826 u16 vid = adapter->hw.mng_cookie.vlan_id; 2827 u16 old_vid = adapter->mng_vlan_id; 2828 2829 if (adapter->hw.mng_cookie.status & E1000_MNG_DHCP_COOKIE_STATUS_VLAN) { 2830 e1000_vlan_rx_add_vid(netdev, htons(ETH_P_8021Q), vid); 2831 adapter->mng_vlan_id = vid; 2832 } 2833 2834 if ((old_vid != (u16)E1000_MNG_VLAN_NONE) && (vid != old_vid)) 2835 e1000_vlan_rx_kill_vid(netdev, htons(ETH_P_8021Q), old_vid); 2836 } 2837 2838 static void e1000_restore_vlan(struct e1000_adapter *adapter) 2839 { 2840 u16 vid; 2841 2842 e1000_vlan_rx_add_vid(adapter->netdev, htons(ETH_P_8021Q), 0); 2843 2844 for_each_set_bit(vid, adapter->active_vlans, VLAN_N_VID) 2845 e1000_vlan_rx_add_vid(adapter->netdev, htons(ETH_P_8021Q), vid); 2846 } 2847 2848 static void e1000_init_manageability_pt(struct e1000_adapter *adapter) 2849 { 2850 struct e1000_hw *hw = &adapter->hw; 2851 u32 manc, manc2h, mdef, i, j; 2852 2853 if (!(adapter->flags & FLAG_MNG_PT_ENABLED)) 2854 return; 2855 2856 manc = er32(MANC); 2857 2858 /* enable receiving management packets to the host. this will probably 2859 * generate destination unreachable messages from the host OS, but 2860 * the packets will be handled on SMBUS 2861 */ 2862 manc |= E1000_MANC_EN_MNG2HOST; 2863 manc2h = er32(MANC2H); 2864 2865 switch (hw->mac.type) { 2866 default: 2867 manc2h |= (E1000_MANC2H_PORT_623 | E1000_MANC2H_PORT_664); 2868 break; 2869 case e1000_82574: 2870 case e1000_82583: 2871 /* Check if IPMI pass-through decision filter already exists; 2872 * if so, enable it. 2873 */ 2874 for (i = 0, j = 0; i < 8; i++) { 2875 mdef = er32(MDEF(i)); 2876 2877 /* Ignore filters with anything other than IPMI ports */ 2878 if (mdef & ~(E1000_MDEF_PORT_623 | E1000_MDEF_PORT_664)) 2879 continue; 2880 2881 /* Enable this decision filter in MANC2H */ 2882 if (mdef) 2883 manc2h |= BIT(i); 2884 2885 j |= mdef; 2886 } 2887 2888 if (j == (E1000_MDEF_PORT_623 | E1000_MDEF_PORT_664)) 2889 break; 2890 2891 /* Create new decision filter in an empty filter */ 2892 for (i = 0, j = 0; i < 8; i++) 2893 if (er32(MDEF(i)) == 0) { 2894 ew32(MDEF(i), (E1000_MDEF_PORT_623 | 2895 E1000_MDEF_PORT_664)); 2896 manc2h |= BIT(1); 2897 j++; 2898 break; 2899 } 2900 2901 if (!j) 2902 e_warn("Unable to create IPMI pass-through filter\n"); 2903 break; 2904 } 2905 2906 ew32(MANC2H, manc2h); 2907 ew32(MANC, manc); 2908 } 2909 2910 /** 2911 * e1000_configure_tx - Configure Transmit Unit after Reset 2912 * @adapter: board private structure 2913 * 2914 * Configure the Tx unit of the MAC after a reset. 2915 **/ 2916 static void e1000_configure_tx(struct e1000_adapter *adapter) 2917 { 2918 struct e1000_hw *hw = &adapter->hw; 2919 struct e1000_ring *tx_ring = adapter->tx_ring; 2920 u64 tdba; 2921 u32 tdlen, tctl, tarc; 2922 2923 /* Setup the HW Tx Head and Tail descriptor pointers */ 2924 tdba = tx_ring->dma; 2925 tdlen = tx_ring->count * sizeof(struct e1000_tx_desc); 2926 ew32(TDBAL(0), (tdba & DMA_BIT_MASK(32))); 2927 ew32(TDBAH(0), (tdba >> 32)); 2928 ew32(TDLEN(0), tdlen); 2929 ew32(TDH(0), 0); 2930 ew32(TDT(0), 0); 2931 tx_ring->head = adapter->hw.hw_addr + E1000_TDH(0); 2932 tx_ring->tail = adapter->hw.hw_addr + E1000_TDT(0); 2933 2934 writel(0, tx_ring->head); 2935 if (adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA) 2936 e1000e_update_tdt_wa(tx_ring, 0); 2937 else 2938 writel(0, tx_ring->tail); 2939 2940 /* Set the Tx Interrupt Delay register */ 2941 ew32(TIDV, adapter->tx_int_delay); 2942 /* Tx irq moderation */ 2943 ew32(TADV, adapter->tx_abs_int_delay); 2944 2945 if (adapter->flags2 & FLAG2_DMA_BURST) { 2946 u32 txdctl = er32(TXDCTL(0)); 2947 2948 txdctl &= ~(E1000_TXDCTL_PTHRESH | E1000_TXDCTL_HTHRESH | 2949 E1000_TXDCTL_WTHRESH); 2950 /* set up some performance related parameters to encourage the 2951 * hardware to use the bus more efficiently in bursts, depends 2952 * on the tx_int_delay to be enabled, 2953 * wthresh = 1 ==> burst write is disabled to avoid Tx stalls 2954 * hthresh = 1 ==> prefetch when one or more available 2955 * pthresh = 0x1f ==> prefetch if internal cache 31 or less 2956 * BEWARE: this seems to work but should be considered first if 2957 * there are Tx hangs or other Tx related bugs 2958 */ 2959 txdctl |= E1000_TXDCTL_DMA_BURST_ENABLE; 2960 ew32(TXDCTL(0), txdctl); 2961 } 2962 /* erratum work around: set txdctl the same for both queues */ 2963 ew32(TXDCTL(1), er32(TXDCTL(0))); 2964 2965 /* Program the Transmit Control Register */ 2966 tctl = er32(TCTL); 2967 tctl &= ~E1000_TCTL_CT; 2968 tctl |= E1000_TCTL_PSP | E1000_TCTL_RTLC | 2969 (E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT); 2970 2971 if (adapter->flags & FLAG_TARC_SPEED_MODE_BIT) { 2972 tarc = er32(TARC(0)); 2973 /* set the speed mode bit, we'll clear it if we're not at 2974 * gigabit link later 2975 */ 2976 #define SPEED_MODE_BIT BIT(21) 2977 tarc |= SPEED_MODE_BIT; 2978 ew32(TARC(0), tarc); 2979 } 2980 2981 /* errata: program both queues to unweighted RR */ 2982 if (adapter->flags & FLAG_TARC_SET_BIT_ZERO) { 2983 tarc = er32(TARC(0)); 2984 tarc |= 1; 2985 ew32(TARC(0), tarc); 2986 tarc = er32(TARC(1)); 2987 tarc |= 1; 2988 ew32(TARC(1), tarc); 2989 } 2990 2991 /* Setup Transmit Descriptor Settings for eop descriptor */ 2992 adapter->txd_cmd = E1000_TXD_CMD_EOP | E1000_TXD_CMD_IFCS; 2993 2994 /* only set IDE if we are delaying interrupts using the timers */ 2995 if (adapter->tx_int_delay) 2996 adapter->txd_cmd |= E1000_TXD_CMD_IDE; 2997 2998 /* enable Report Status bit */ 2999 adapter->txd_cmd |= E1000_TXD_CMD_RS; 3000 3001 ew32(TCTL, tctl); 3002 3003 hw->mac.ops.config_collision_dist(hw); 3004 3005 /* SPT and KBL Si errata workaround to avoid data corruption */ 3006 if (hw->mac.type == e1000_pch_spt) { 3007 u32 reg_val; 3008 3009 reg_val = er32(IOSFPC); 3010 reg_val |= E1000_RCTL_RDMTS_HEX; 3011 ew32(IOSFPC, reg_val); 3012 3013 reg_val = er32(TARC(0)); 3014 /* SPT and KBL Si errata workaround to avoid Tx hang. 3015 * Dropping the number of outstanding requests from 3016 * 3 to 2 in order to avoid a buffer overrun. 3017 */ 3018 reg_val &= ~E1000_TARC0_CB_MULTIQ_3_REQ; 3019 reg_val |= E1000_TARC0_CB_MULTIQ_2_REQ; 3020 ew32(TARC(0), reg_val); 3021 } 3022 } 3023 3024 #define PAGE_USE_COUNT(S) (((S) >> PAGE_SHIFT) + \ 3025 (((S) & (PAGE_SIZE - 1)) ? 1 : 0)) 3026 3027 /** 3028 * e1000_setup_rctl - configure the receive control registers 3029 * @adapter: Board private structure 3030 **/ 3031 static void e1000_setup_rctl(struct e1000_adapter *adapter) 3032 { 3033 struct e1000_hw *hw = &adapter->hw; 3034 u32 rctl, rfctl; 3035 u32 pages = 0; 3036 3037 /* Workaround Si errata on PCHx - configure jumbo frame flow. 3038 * If jumbo frames not set, program related MAC/PHY registers 3039 * to h/w defaults 3040 */ 3041 if (hw->mac.type >= e1000_pch2lan) { 3042 s32 ret_val; 3043 3044 if (adapter->netdev->mtu > ETH_DATA_LEN) 3045 ret_val = e1000_lv_jumbo_workaround_ich8lan(hw, true); 3046 else 3047 ret_val = e1000_lv_jumbo_workaround_ich8lan(hw, false); 3048 3049 if (ret_val) 3050 e_dbg("failed to enable|disable jumbo frame workaround mode\n"); 3051 } 3052 3053 /* Program MC offset vector base */ 3054 rctl = er32(RCTL); 3055 rctl &= ~(3 << E1000_RCTL_MO_SHIFT); 3056 rctl |= E1000_RCTL_EN | E1000_RCTL_BAM | 3057 E1000_RCTL_LBM_NO | E1000_RCTL_RDMTS_HALF | 3058 (adapter->hw.mac.mc_filter_type << E1000_RCTL_MO_SHIFT); 3059 3060 /* Do not Store bad packets */ 3061 rctl &= ~E1000_RCTL_SBP; 3062 3063 /* Enable Long Packet receive */ 3064 if (adapter->netdev->mtu <= ETH_DATA_LEN) 3065 rctl &= ~E1000_RCTL_LPE; 3066 else 3067 rctl |= E1000_RCTL_LPE; 3068 3069 /* Some systems expect that the CRC is included in SMBUS traffic. The 3070 * hardware strips the CRC before sending to both SMBUS (BMC) and to 3071 * host memory when this is enabled 3072 */ 3073 if (adapter->flags2 & FLAG2_CRC_STRIPPING) 3074 rctl |= E1000_RCTL_SECRC; 3075 3076 /* Workaround Si errata on 82577 PHY - configure IPG for jumbos */ 3077 if ((hw->phy.type == e1000_phy_82577) && (rctl & E1000_RCTL_LPE)) { 3078 u16 phy_data; 3079 3080 e1e_rphy(hw, PHY_REG(770, 26), &phy_data); 3081 phy_data &= 0xfff8; 3082 phy_data |= BIT(2); 3083 e1e_wphy(hw, PHY_REG(770, 26), phy_data); 3084 3085 e1e_rphy(hw, 22, &phy_data); 3086 phy_data &= 0x0fff; 3087 phy_data |= BIT(14); 3088 e1e_wphy(hw, 0x10, 0x2823); 3089 e1e_wphy(hw, 0x11, 0x0003); 3090 e1e_wphy(hw, 22, phy_data); 3091 } 3092 3093 /* Setup buffer sizes */ 3094 rctl &= ~E1000_RCTL_SZ_4096; 3095 rctl |= E1000_RCTL_BSEX; 3096 switch (adapter->rx_buffer_len) { 3097 case 2048: 3098 default: 3099 rctl |= E1000_RCTL_SZ_2048; 3100 rctl &= ~E1000_RCTL_BSEX; 3101 break; 3102 case 4096: 3103 rctl |= E1000_RCTL_SZ_4096; 3104 break; 3105 case 8192: 3106 rctl |= E1000_RCTL_SZ_8192; 3107 break; 3108 case 16384: 3109 rctl |= E1000_RCTL_SZ_16384; 3110 break; 3111 } 3112 3113 /* Enable Extended Status in all Receive Descriptors */ 3114 rfctl = er32(RFCTL); 3115 rfctl |= E1000_RFCTL_EXTEN; 3116 ew32(RFCTL, rfctl); 3117 3118 /* 82571 and greater support packet-split where the protocol 3119 * header is placed in skb->data and the packet data is 3120 * placed in pages hanging off of skb_shinfo(skb)->nr_frags. 3121 * In the case of a non-split, skb->data is linearly filled, 3122 * followed by the page buffers. Therefore, skb->data is 3123 * sized to hold the largest protocol header. 3124 * 3125 * allocations using alloc_page take too long for regular MTU 3126 * so only enable packet split for jumbo frames 3127 * 3128 * Using pages when the page size is greater than 16k wastes 3129 * a lot of memory, since we allocate 3 pages at all times 3130 * per packet. 3131 */ 3132 pages = PAGE_USE_COUNT(adapter->netdev->mtu); 3133 if ((pages <= 3) && (PAGE_SIZE <= 16384) && (rctl & E1000_RCTL_LPE)) 3134 adapter->rx_ps_pages = pages; 3135 else 3136 adapter->rx_ps_pages = 0; 3137 3138 if (adapter->rx_ps_pages) { 3139 u32 psrctl = 0; 3140 3141 /* Enable Packet split descriptors */ 3142 rctl |= E1000_RCTL_DTYP_PS; 3143 3144 psrctl |= adapter->rx_ps_bsize0 >> E1000_PSRCTL_BSIZE0_SHIFT; 3145 3146 switch (adapter->rx_ps_pages) { 3147 case 3: 3148 psrctl |= PAGE_SIZE << E1000_PSRCTL_BSIZE3_SHIFT; 3149 fallthrough; 3150 case 2: 3151 psrctl |= PAGE_SIZE << E1000_PSRCTL_BSIZE2_SHIFT; 3152 fallthrough; 3153 case 1: 3154 psrctl |= PAGE_SIZE >> E1000_PSRCTL_BSIZE1_SHIFT; 3155 break; 3156 } 3157 3158 ew32(PSRCTL, psrctl); 3159 } 3160 3161 /* This is useful for sniffing bad packets. */ 3162 if (adapter->netdev->features & NETIF_F_RXALL) { 3163 /* UPE and MPE will be handled by normal PROMISC logic 3164 * in e1000e_set_rx_mode 3165 */ 3166 rctl |= (E1000_RCTL_SBP | /* Receive bad packets */ 3167 E1000_RCTL_BAM | /* RX All Bcast Pkts */ 3168 E1000_RCTL_PMCF); /* RX All MAC Ctrl Pkts */ 3169 3170 rctl &= ~(E1000_RCTL_VFE | /* Disable VLAN filter */ 3171 E1000_RCTL_DPF | /* Allow filtered pause */ 3172 E1000_RCTL_CFIEN); /* Dis VLAN CFIEN Filter */ 3173 /* Do not mess with E1000_CTRL_VME, it affects transmit as well, 3174 * and that breaks VLANs. 3175 */ 3176 } 3177 3178 ew32(RCTL, rctl); 3179 /* just started the receive unit, no need to restart */ 3180 adapter->flags &= ~FLAG_RESTART_NOW; 3181 } 3182 3183 /** 3184 * e1000_configure_rx - Configure Receive Unit after Reset 3185 * @adapter: board private structure 3186 * 3187 * Configure the Rx unit of the MAC after a reset. 3188 **/ 3189 static void e1000_configure_rx(struct e1000_adapter *adapter) 3190 { 3191 struct e1000_hw *hw = &adapter->hw; 3192 struct e1000_ring *rx_ring = adapter->rx_ring; 3193 u64 rdba; 3194 u32 rdlen, rctl, rxcsum, ctrl_ext; 3195 3196 if (adapter->rx_ps_pages) { 3197 /* this is a 32 byte descriptor */ 3198 rdlen = rx_ring->count * 3199 sizeof(union e1000_rx_desc_packet_split); 3200 adapter->clean_rx = e1000_clean_rx_irq_ps; 3201 adapter->alloc_rx_buf = e1000_alloc_rx_buffers_ps; 3202 } else if (adapter->netdev->mtu > ETH_FRAME_LEN + ETH_FCS_LEN) { 3203 rdlen = rx_ring->count * sizeof(union e1000_rx_desc_extended); 3204 adapter->clean_rx = e1000_clean_jumbo_rx_irq; 3205 adapter->alloc_rx_buf = e1000_alloc_jumbo_rx_buffers; 3206 } else { 3207 rdlen = rx_ring->count * sizeof(union e1000_rx_desc_extended); 3208 adapter->clean_rx = e1000_clean_rx_irq; 3209 adapter->alloc_rx_buf = e1000_alloc_rx_buffers; 3210 } 3211 3212 /* disable receives while setting up the descriptors */ 3213 rctl = er32(RCTL); 3214 if (!(adapter->flags2 & FLAG2_NO_DISABLE_RX)) 3215 ew32(RCTL, rctl & ~E1000_RCTL_EN); 3216 e1e_flush(); 3217 usleep_range(10000, 11000); 3218 3219 if (adapter->flags2 & FLAG2_DMA_BURST) { 3220 /* set the writeback threshold (only takes effect if the RDTR 3221 * is set). set GRAN=1 and write back up to 0x4 worth, and 3222 * enable prefetching of 0x20 Rx descriptors 3223 * granularity = 01 3224 * wthresh = 04, 3225 * hthresh = 04, 3226 * pthresh = 0x20 3227 */ 3228 ew32(RXDCTL(0), E1000_RXDCTL_DMA_BURST_ENABLE); 3229 ew32(RXDCTL(1), E1000_RXDCTL_DMA_BURST_ENABLE); 3230 } 3231 3232 /* set the Receive Delay Timer Register */ 3233 ew32(RDTR, adapter->rx_int_delay); 3234 3235 /* irq moderation */ 3236 ew32(RADV, adapter->rx_abs_int_delay); 3237 if ((adapter->itr_setting != 0) && (adapter->itr != 0)) 3238 e1000e_write_itr(adapter, adapter->itr); 3239 3240 ctrl_ext = er32(CTRL_EXT); 3241 /* Auto-Mask interrupts upon ICR access */ 3242 ctrl_ext |= E1000_CTRL_EXT_IAME; 3243 ew32(IAM, 0xffffffff); 3244 ew32(CTRL_EXT, ctrl_ext); 3245 e1e_flush(); 3246 3247 /* Setup the HW Rx Head and Tail Descriptor Pointers and 3248 * the Base and Length of the Rx Descriptor Ring 3249 */ 3250 rdba = rx_ring->dma; 3251 ew32(RDBAL(0), (rdba & DMA_BIT_MASK(32))); 3252 ew32(RDBAH(0), (rdba >> 32)); 3253 ew32(RDLEN(0), rdlen); 3254 ew32(RDH(0), 0); 3255 ew32(RDT(0), 0); 3256 rx_ring->head = adapter->hw.hw_addr + E1000_RDH(0); 3257 rx_ring->tail = adapter->hw.hw_addr + E1000_RDT(0); 3258 3259 writel(0, rx_ring->head); 3260 if (adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA) 3261 e1000e_update_rdt_wa(rx_ring, 0); 3262 else 3263 writel(0, rx_ring->tail); 3264 3265 /* Enable Receive Checksum Offload for TCP and UDP */ 3266 rxcsum = er32(RXCSUM); 3267 if (adapter->netdev->features & NETIF_F_RXCSUM) 3268 rxcsum |= E1000_RXCSUM_TUOFL; 3269 else 3270 rxcsum &= ~E1000_RXCSUM_TUOFL; 3271 ew32(RXCSUM, rxcsum); 3272 3273 /* With jumbo frames, excessive C-state transition latencies result 3274 * in dropped transactions. 3275 */ 3276 if (adapter->netdev->mtu > ETH_DATA_LEN) { 3277 u32 lat = 3278 ((er32(PBA) & E1000_PBA_RXA_MASK) * 1024 - 3279 adapter->max_frame_size) * 8 / 1000; 3280 3281 if (adapter->flags & FLAG_IS_ICH) { 3282 u32 rxdctl = er32(RXDCTL(0)); 3283 3284 ew32(RXDCTL(0), rxdctl | 0x3 | BIT(8)); 3285 } 3286 3287 dev_info(&adapter->pdev->dev, 3288 "Some CPU C-states have been disabled in order to enable jumbo frames\n"); 3289 cpu_latency_qos_update_request(&adapter->pm_qos_req, lat); 3290 } else { 3291 cpu_latency_qos_update_request(&adapter->pm_qos_req, 3292 PM_QOS_DEFAULT_VALUE); 3293 } 3294 3295 /* Enable Receives */ 3296 ew32(RCTL, rctl); 3297 } 3298 3299 /** 3300 * e1000e_write_mc_addr_list - write multicast addresses to MTA 3301 * @netdev: network interface device structure 3302 * 3303 * Writes multicast address list to the MTA hash table. 3304 * Returns: -ENOMEM on failure 3305 * 0 on no addresses written 3306 * X on writing X addresses to MTA 3307 */ 3308 static int e1000e_write_mc_addr_list(struct net_device *netdev) 3309 { 3310 struct e1000_adapter *adapter = netdev_priv(netdev); 3311 struct e1000_hw *hw = &adapter->hw; 3312 struct netdev_hw_addr *ha; 3313 u8 *mta_list; 3314 int i; 3315 3316 if (netdev_mc_empty(netdev)) { 3317 /* nothing to program, so clear mc list */ 3318 hw->mac.ops.update_mc_addr_list(hw, NULL, 0); 3319 return 0; 3320 } 3321 3322 mta_list = kcalloc(netdev_mc_count(netdev), ETH_ALEN, GFP_ATOMIC); 3323 if (!mta_list) 3324 return -ENOMEM; 3325 3326 /* update_mc_addr_list expects a packed array of only addresses. */ 3327 i = 0; 3328 netdev_for_each_mc_addr(ha, netdev) 3329 memcpy(mta_list + (i++ * ETH_ALEN), ha->addr, ETH_ALEN); 3330 3331 hw->mac.ops.update_mc_addr_list(hw, mta_list, i); 3332 kfree(mta_list); 3333 3334 return netdev_mc_count(netdev); 3335 } 3336 3337 /** 3338 * e1000e_write_uc_addr_list - write unicast addresses to RAR table 3339 * @netdev: network interface device structure 3340 * 3341 * Writes unicast address list to the RAR table. 3342 * Returns: -ENOMEM on failure/insufficient address space 3343 * 0 on no addresses written 3344 * X on writing X addresses to the RAR table 3345 **/ 3346 static int e1000e_write_uc_addr_list(struct net_device *netdev) 3347 { 3348 struct e1000_adapter *adapter = netdev_priv(netdev); 3349 struct e1000_hw *hw = &adapter->hw; 3350 unsigned int rar_entries; 3351 int count = 0; 3352 3353 rar_entries = hw->mac.ops.rar_get_count(hw); 3354 3355 /* save a rar entry for our hardware address */ 3356 rar_entries--; 3357 3358 /* save a rar entry for the LAA workaround */ 3359 if (adapter->flags & FLAG_RESET_OVERWRITES_LAA) 3360 rar_entries--; 3361 3362 /* return ENOMEM indicating insufficient memory for addresses */ 3363 if (netdev_uc_count(netdev) > rar_entries) 3364 return -ENOMEM; 3365 3366 if (!netdev_uc_empty(netdev) && rar_entries) { 3367 struct netdev_hw_addr *ha; 3368 3369 /* write the addresses in reverse order to avoid write 3370 * combining 3371 */ 3372 netdev_for_each_uc_addr(ha, netdev) { 3373 int ret_val; 3374 3375 if (!rar_entries) 3376 break; 3377 ret_val = hw->mac.ops.rar_set(hw, ha->addr, rar_entries--); 3378 if (ret_val < 0) 3379 return -ENOMEM; 3380 count++; 3381 } 3382 } 3383 3384 /* zero out the remaining RAR entries not used above */ 3385 for (; rar_entries > 0; rar_entries--) { 3386 ew32(RAH(rar_entries), 0); 3387 ew32(RAL(rar_entries), 0); 3388 } 3389 e1e_flush(); 3390 3391 return count; 3392 } 3393 3394 /** 3395 * e1000e_set_rx_mode - secondary unicast, Multicast and Promiscuous mode set 3396 * @netdev: network interface device structure 3397 * 3398 * The ndo_set_rx_mode entry point is called whenever the unicast or multicast 3399 * address list or the network interface flags are updated. This routine is 3400 * responsible for configuring the hardware for proper unicast, multicast, 3401 * promiscuous mode, and all-multi behavior. 3402 **/ 3403 static void e1000e_set_rx_mode(struct net_device *netdev) 3404 { 3405 struct e1000_adapter *adapter = netdev_priv(netdev); 3406 struct e1000_hw *hw = &adapter->hw; 3407 u32 rctl; 3408 3409 if (pm_runtime_suspended(netdev->dev.parent)) 3410 return; 3411 3412 /* Check for Promiscuous and All Multicast modes */ 3413 rctl = er32(RCTL); 3414 3415 /* clear the affected bits */ 3416 rctl &= ~(E1000_RCTL_UPE | E1000_RCTL_MPE); 3417 3418 if (netdev->flags & IFF_PROMISC) { 3419 rctl |= (E1000_RCTL_UPE | E1000_RCTL_MPE); 3420 /* Do not hardware filter VLANs in promisc mode */ 3421 e1000e_vlan_filter_disable(adapter); 3422 } else { 3423 int count; 3424 3425 if (netdev->flags & IFF_ALLMULTI) { 3426 rctl |= E1000_RCTL_MPE; 3427 } else { 3428 /* Write addresses to the MTA, if the attempt fails 3429 * then we should just turn on promiscuous mode so 3430 * that we can at least receive multicast traffic 3431 */ 3432 count = e1000e_write_mc_addr_list(netdev); 3433 if (count < 0) 3434 rctl |= E1000_RCTL_MPE; 3435 } 3436 e1000e_vlan_filter_enable(adapter); 3437 /* Write addresses to available RAR registers, if there is not 3438 * sufficient space to store all the addresses then enable 3439 * unicast promiscuous mode 3440 */ 3441 count = e1000e_write_uc_addr_list(netdev); 3442 if (count < 0) 3443 rctl |= E1000_RCTL_UPE; 3444 } 3445 3446 ew32(RCTL, rctl); 3447 3448 if (netdev->features & NETIF_F_HW_VLAN_CTAG_RX) 3449 e1000e_vlan_strip_enable(adapter); 3450 else 3451 e1000e_vlan_strip_disable(adapter); 3452 } 3453 3454 static void e1000e_setup_rss_hash(struct e1000_adapter *adapter) 3455 { 3456 struct e1000_hw *hw = &adapter->hw; 3457 u32 mrqc, rxcsum; 3458 u32 rss_key[10]; 3459 int i; 3460 3461 netdev_rss_key_fill(rss_key, sizeof(rss_key)); 3462 for (i = 0; i < 10; i++) 3463 ew32(RSSRK(i), rss_key[i]); 3464 3465 /* Direct all traffic to queue 0 */ 3466 for (i = 0; i < 32; i++) 3467 ew32(RETA(i), 0); 3468 3469 /* Disable raw packet checksumming so that RSS hash is placed in 3470 * descriptor on writeback. 3471 */ 3472 rxcsum = er32(RXCSUM); 3473 rxcsum |= E1000_RXCSUM_PCSD; 3474 3475 ew32(RXCSUM, rxcsum); 3476 3477 mrqc = (E1000_MRQC_RSS_FIELD_IPV4 | 3478 E1000_MRQC_RSS_FIELD_IPV4_TCP | 3479 E1000_MRQC_RSS_FIELD_IPV6 | 3480 E1000_MRQC_RSS_FIELD_IPV6_TCP | 3481 E1000_MRQC_RSS_FIELD_IPV6_TCP_EX); 3482 3483 ew32(MRQC, mrqc); 3484 } 3485 3486 /** 3487 * e1000e_get_base_timinca - get default SYSTIM time increment attributes 3488 * @adapter: board private structure 3489 * @timinca: pointer to returned time increment attributes 3490 * 3491 * Get attributes for incrementing the System Time Register SYSTIML/H at 3492 * the default base frequency, and set the cyclecounter shift value. 3493 **/ 3494 s32 e1000e_get_base_timinca(struct e1000_adapter *adapter, u32 *timinca) 3495 { 3496 struct e1000_hw *hw = &adapter->hw; 3497 u32 incvalue, incperiod, shift; 3498 3499 /* Make sure clock is enabled on I217/I218/I219 before checking 3500 * the frequency 3501 */ 3502 if ((hw->mac.type >= e1000_pch_lpt) && 3503 !(er32(TSYNCTXCTL) & E1000_TSYNCTXCTL_ENABLED) && 3504 !(er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_ENABLED)) { 3505 u32 fextnvm7 = er32(FEXTNVM7); 3506 3507 if (!(fextnvm7 & BIT(0))) { 3508 ew32(FEXTNVM7, fextnvm7 | BIT(0)); 3509 e1e_flush(); 3510 } 3511 } 3512 3513 switch (hw->mac.type) { 3514 case e1000_pch2lan: 3515 /* Stable 96MHz frequency */ 3516 incperiod = INCPERIOD_96MHZ; 3517 incvalue = INCVALUE_96MHZ; 3518 shift = INCVALUE_SHIFT_96MHZ; 3519 adapter->cc.shift = shift + INCPERIOD_SHIFT_96MHZ; 3520 break; 3521 case e1000_pch_lpt: 3522 if (er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_SYSCFI) { 3523 /* Stable 96MHz frequency */ 3524 incperiod = INCPERIOD_96MHZ; 3525 incvalue = INCVALUE_96MHZ; 3526 shift = INCVALUE_SHIFT_96MHZ; 3527 adapter->cc.shift = shift + INCPERIOD_SHIFT_96MHZ; 3528 } else { 3529 /* Stable 25MHz frequency */ 3530 incperiod = INCPERIOD_25MHZ; 3531 incvalue = INCVALUE_25MHZ; 3532 shift = INCVALUE_SHIFT_25MHZ; 3533 adapter->cc.shift = shift; 3534 } 3535 break; 3536 case e1000_pch_spt: 3537 /* Stable 24MHz frequency */ 3538 incperiod = INCPERIOD_24MHZ; 3539 incvalue = INCVALUE_24MHZ; 3540 shift = INCVALUE_SHIFT_24MHZ; 3541 adapter->cc.shift = shift; 3542 break; 3543 case e1000_pch_cnp: 3544 case e1000_pch_tgp: 3545 case e1000_pch_adp: 3546 case e1000_pch_mtp: 3547 case e1000_pch_lnp: 3548 case e1000_pch_ptp: 3549 if (er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_SYSCFI) { 3550 /* Stable 24MHz frequency */ 3551 incperiod = INCPERIOD_24MHZ; 3552 incvalue = INCVALUE_24MHZ; 3553 shift = INCVALUE_SHIFT_24MHZ; 3554 adapter->cc.shift = shift; 3555 } else { 3556 /* Stable 38400KHz frequency */ 3557 incperiod = INCPERIOD_38400KHZ; 3558 incvalue = INCVALUE_38400KHZ; 3559 shift = INCVALUE_SHIFT_38400KHZ; 3560 adapter->cc.shift = shift; 3561 } 3562 break; 3563 case e1000_82574: 3564 case e1000_82583: 3565 /* Stable 25MHz frequency */ 3566 incperiod = INCPERIOD_25MHZ; 3567 incvalue = INCVALUE_25MHZ; 3568 shift = INCVALUE_SHIFT_25MHZ; 3569 adapter->cc.shift = shift; 3570 break; 3571 default: 3572 return -EINVAL; 3573 } 3574 3575 *timinca = ((incperiod << E1000_TIMINCA_INCPERIOD_SHIFT) | 3576 ((incvalue << shift) & E1000_TIMINCA_INCVALUE_MASK)); 3577 3578 return 0; 3579 } 3580 3581 /** 3582 * e1000e_config_hwtstamp - configure the hwtstamp registers and enable/disable 3583 * @adapter: board private structure 3584 * @config: timestamp configuration 3585 * 3586 * Outgoing time stamping can be enabled and disabled. Play nice and 3587 * disable it when requested, although it shouldn't cause any overhead 3588 * when no packet needs it. At most one packet in the queue may be 3589 * marked for time stamping, otherwise it would be impossible to tell 3590 * for sure to which packet the hardware time stamp belongs. 3591 * 3592 * Incoming time stamping has to be configured via the hardware filters. 3593 * Not all combinations are supported, in particular event type has to be 3594 * specified. Matching the kind of event packet is not supported, with the 3595 * exception of "all V2 events regardless of level 2 or 4". 3596 **/ 3597 static int e1000e_config_hwtstamp(struct e1000_adapter *adapter, 3598 struct hwtstamp_config *config) 3599 { 3600 struct e1000_hw *hw = &adapter->hw; 3601 u32 tsync_tx_ctl = E1000_TSYNCTXCTL_ENABLED; 3602 u32 tsync_rx_ctl = E1000_TSYNCRXCTL_ENABLED; 3603 u32 rxmtrl = 0; 3604 u16 rxudp = 0; 3605 bool is_l4 = false; 3606 bool is_l2 = false; 3607 u32 regval; 3608 3609 if (!(adapter->flags & FLAG_HAS_HW_TIMESTAMP)) 3610 return -EINVAL; 3611 3612 switch (config->tx_type) { 3613 case HWTSTAMP_TX_OFF: 3614 tsync_tx_ctl = 0; 3615 break; 3616 case HWTSTAMP_TX_ON: 3617 break; 3618 default: 3619 return -ERANGE; 3620 } 3621 3622 switch (config->rx_filter) { 3623 case HWTSTAMP_FILTER_NONE: 3624 tsync_rx_ctl = 0; 3625 break; 3626 case HWTSTAMP_FILTER_PTP_V1_L4_SYNC: 3627 tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L4_V1; 3628 rxmtrl = E1000_RXMTRL_PTP_V1_SYNC_MESSAGE; 3629 is_l4 = true; 3630 break; 3631 case HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ: 3632 tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L4_V1; 3633 rxmtrl = E1000_RXMTRL_PTP_V1_DELAY_REQ_MESSAGE; 3634 is_l4 = true; 3635 break; 3636 case HWTSTAMP_FILTER_PTP_V2_L2_SYNC: 3637 /* Also time stamps V2 L2 Path Delay Request/Response */ 3638 tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L2_V2; 3639 rxmtrl = E1000_RXMTRL_PTP_V2_SYNC_MESSAGE; 3640 is_l2 = true; 3641 break; 3642 case HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ: 3643 /* Also time stamps V2 L2 Path Delay Request/Response. */ 3644 tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L2_V2; 3645 rxmtrl = E1000_RXMTRL_PTP_V2_DELAY_REQ_MESSAGE; 3646 is_l2 = true; 3647 break; 3648 case HWTSTAMP_FILTER_PTP_V2_L4_SYNC: 3649 /* Hardware cannot filter just V2 L4 Sync messages */ 3650 fallthrough; 3651 case HWTSTAMP_FILTER_PTP_V2_SYNC: 3652 /* Also time stamps V2 Path Delay Request/Response. */ 3653 tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L2_L4_V2; 3654 rxmtrl = E1000_RXMTRL_PTP_V2_SYNC_MESSAGE; 3655 is_l2 = true; 3656 is_l4 = true; 3657 break; 3658 case HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ: 3659 /* Hardware cannot filter just V2 L4 Delay Request messages */ 3660 fallthrough; 3661 case HWTSTAMP_FILTER_PTP_V2_DELAY_REQ: 3662 /* Also time stamps V2 Path Delay Request/Response. */ 3663 tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L2_L4_V2; 3664 rxmtrl = E1000_RXMTRL_PTP_V2_DELAY_REQ_MESSAGE; 3665 is_l2 = true; 3666 is_l4 = true; 3667 break; 3668 case HWTSTAMP_FILTER_PTP_V2_L4_EVENT: 3669 case HWTSTAMP_FILTER_PTP_V2_L2_EVENT: 3670 /* Hardware cannot filter just V2 L4 or L2 Event messages */ 3671 fallthrough; 3672 case HWTSTAMP_FILTER_PTP_V2_EVENT: 3673 tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_EVENT_V2; 3674 config->rx_filter = HWTSTAMP_FILTER_PTP_V2_EVENT; 3675 is_l2 = true; 3676 is_l4 = true; 3677 break; 3678 case HWTSTAMP_FILTER_PTP_V1_L4_EVENT: 3679 /* For V1, the hardware can only filter Sync messages or 3680 * Delay Request messages but not both so fall-through to 3681 * time stamp all packets. 3682 */ 3683 fallthrough; 3684 case HWTSTAMP_FILTER_NTP_ALL: 3685 case HWTSTAMP_FILTER_ALL: 3686 is_l2 = true; 3687 is_l4 = true; 3688 tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_ALL; 3689 config->rx_filter = HWTSTAMP_FILTER_ALL; 3690 break; 3691 default: 3692 return -ERANGE; 3693 } 3694 3695 adapter->hwtstamp_config = *config; 3696 3697 /* enable/disable Tx h/w time stamping */ 3698 regval = er32(TSYNCTXCTL); 3699 regval &= ~E1000_TSYNCTXCTL_ENABLED; 3700 regval |= tsync_tx_ctl; 3701 ew32(TSYNCTXCTL, regval); 3702 if ((er32(TSYNCTXCTL) & E1000_TSYNCTXCTL_ENABLED) != 3703 (regval & E1000_TSYNCTXCTL_ENABLED)) { 3704 e_err("Timesync Tx Control register not set as expected\n"); 3705 return -EAGAIN; 3706 } 3707 3708 /* enable/disable Rx h/w time stamping */ 3709 regval = er32(TSYNCRXCTL); 3710 regval &= ~(E1000_TSYNCRXCTL_ENABLED | E1000_TSYNCRXCTL_TYPE_MASK); 3711 regval |= tsync_rx_ctl; 3712 ew32(TSYNCRXCTL, regval); 3713 if ((er32(TSYNCRXCTL) & (E1000_TSYNCRXCTL_ENABLED | 3714 E1000_TSYNCRXCTL_TYPE_MASK)) != 3715 (regval & (E1000_TSYNCRXCTL_ENABLED | 3716 E1000_TSYNCRXCTL_TYPE_MASK))) { 3717 e_err("Timesync Rx Control register not set as expected\n"); 3718 return -EAGAIN; 3719 } 3720 3721 /* L2: define ethertype filter for time stamped packets */ 3722 if (is_l2) 3723 rxmtrl |= ETH_P_1588; 3724 3725 /* define which PTP packets get time stamped */ 3726 ew32(RXMTRL, rxmtrl); 3727 3728 /* Filter by destination port */ 3729 if (is_l4) { 3730 rxudp = PTP_EV_PORT; 3731 cpu_to_be16s(&rxudp); 3732 } 3733 ew32(RXUDP, rxudp); 3734 3735 e1e_flush(); 3736 3737 /* Clear TSYNCRXCTL_VALID & TSYNCTXCTL_VALID bit */ 3738 er32(RXSTMPH); 3739 er32(TXSTMPH); 3740 3741 return 0; 3742 } 3743 3744 /** 3745 * e1000_configure - configure the hardware for Rx and Tx 3746 * @adapter: private board structure 3747 **/ 3748 static void e1000_configure(struct e1000_adapter *adapter) 3749 { 3750 struct e1000_ring *rx_ring = adapter->rx_ring; 3751 3752 e1000e_set_rx_mode(adapter->netdev); 3753 3754 e1000_restore_vlan(adapter); 3755 e1000_init_manageability_pt(adapter); 3756 3757 e1000_configure_tx(adapter); 3758 3759 if (adapter->netdev->features & NETIF_F_RXHASH) 3760 e1000e_setup_rss_hash(adapter); 3761 e1000_setup_rctl(adapter); 3762 e1000_configure_rx(adapter); 3763 adapter->alloc_rx_buf(rx_ring, e1000_desc_unused(rx_ring), GFP_KERNEL); 3764 } 3765 3766 /** 3767 * e1000e_power_up_phy - restore link in case the phy was powered down 3768 * @adapter: address of board private structure 3769 * 3770 * The phy may be powered down to save power and turn off link when the 3771 * driver is unloaded and wake on lan is not enabled (among others) 3772 * *** this routine MUST be followed by a call to e1000e_reset *** 3773 **/ 3774 void e1000e_power_up_phy(struct e1000_adapter *adapter) 3775 { 3776 if (adapter->hw.phy.ops.power_up) 3777 adapter->hw.phy.ops.power_up(&adapter->hw); 3778 3779 adapter->hw.mac.ops.setup_link(&adapter->hw); 3780 } 3781 3782 /** 3783 * e1000_power_down_phy - Power down the PHY 3784 * @adapter: board private structure 3785 * 3786 * Power down the PHY so no link is implied when interface is down. 3787 * The PHY cannot be powered down if management or WoL is active. 3788 */ 3789 static void e1000_power_down_phy(struct e1000_adapter *adapter) 3790 { 3791 if (adapter->hw.phy.ops.power_down) 3792 adapter->hw.phy.ops.power_down(&adapter->hw); 3793 } 3794 3795 /** 3796 * e1000_flush_tx_ring - remove all descriptors from the tx_ring 3797 * @adapter: board private structure 3798 * 3799 * We want to clear all pending descriptors from the TX ring. 3800 * zeroing happens when the HW reads the regs. We assign the ring itself as 3801 * the data of the next descriptor. We don't care about the data we are about 3802 * to reset the HW. 3803 */ 3804 static void e1000_flush_tx_ring(struct e1000_adapter *adapter) 3805 { 3806 struct e1000_hw *hw = &adapter->hw; 3807 struct e1000_ring *tx_ring = adapter->tx_ring; 3808 struct e1000_tx_desc *tx_desc = NULL; 3809 u32 tdt, tctl, txd_lower = E1000_TXD_CMD_IFCS; 3810 u16 size = 512; 3811 3812 tctl = er32(TCTL); 3813 ew32(TCTL, tctl | E1000_TCTL_EN); 3814 tdt = er32(TDT(0)); 3815 BUG_ON(tdt != tx_ring->next_to_use); 3816 tx_desc = E1000_TX_DESC(*tx_ring, tx_ring->next_to_use); 3817 tx_desc->buffer_addr = cpu_to_le64(tx_ring->dma); 3818 3819 tx_desc->lower.data = cpu_to_le32(txd_lower | size); 3820 tx_desc->upper.data = 0; 3821 /* flush descriptors to memory before notifying the HW */ 3822 wmb(); 3823 tx_ring->next_to_use++; 3824 if (tx_ring->next_to_use == tx_ring->count) 3825 tx_ring->next_to_use = 0; 3826 ew32(TDT(0), tx_ring->next_to_use); 3827 usleep_range(200, 250); 3828 } 3829 3830 /** 3831 * e1000_flush_rx_ring - remove all descriptors from the rx_ring 3832 * @adapter: board private structure 3833 * 3834 * Mark all descriptors in the RX ring as consumed and disable the rx ring 3835 */ 3836 static void e1000_flush_rx_ring(struct e1000_adapter *adapter) 3837 { 3838 u32 rctl, rxdctl; 3839 struct e1000_hw *hw = &adapter->hw; 3840 3841 rctl = er32(RCTL); 3842 ew32(RCTL, rctl & ~E1000_RCTL_EN); 3843 e1e_flush(); 3844 usleep_range(100, 150); 3845 3846 rxdctl = er32(RXDCTL(0)); 3847 /* zero the lower 14 bits (prefetch and host thresholds) */ 3848 rxdctl &= 0xffffc000; 3849 3850 /* update thresholds: prefetch threshold to 31, host threshold to 1 3851 * and make sure the granularity is "descriptors" and not "cache lines" 3852 */ 3853 rxdctl |= (0x1F | BIT(8) | E1000_RXDCTL_THRESH_UNIT_DESC); 3854 3855 ew32(RXDCTL(0), rxdctl); 3856 /* momentarily enable the RX ring for the changes to take effect */ 3857 ew32(RCTL, rctl | E1000_RCTL_EN); 3858 e1e_flush(); 3859 usleep_range(100, 150); 3860 ew32(RCTL, rctl & ~E1000_RCTL_EN); 3861 } 3862 3863 /** 3864 * e1000_flush_desc_rings - remove all descriptors from the descriptor rings 3865 * @adapter: board private structure 3866 * 3867 * In i219, the descriptor rings must be emptied before resetting the HW 3868 * or before changing the device state to D3 during runtime (runtime PM). 3869 * 3870 * Failure to do this will cause the HW to enter a unit hang state which can 3871 * only be released by PCI reset on the device 3872 * 3873 */ 3874 3875 static void e1000_flush_desc_rings(struct e1000_adapter *adapter) 3876 { 3877 u16 hang_state; 3878 u32 fext_nvm11, tdlen; 3879 struct e1000_hw *hw = &adapter->hw; 3880 3881 /* First, disable MULR fix in FEXTNVM11 */ 3882 fext_nvm11 = er32(FEXTNVM11); 3883 fext_nvm11 |= E1000_FEXTNVM11_DISABLE_MULR_FIX; 3884 ew32(FEXTNVM11, fext_nvm11); 3885 /* do nothing if we're not in faulty state, or if the queue is empty */ 3886 tdlen = er32(TDLEN(0)); 3887 pci_read_config_word(adapter->pdev, PCICFG_DESC_RING_STATUS, 3888 &hang_state); 3889 if (!(hang_state & FLUSH_DESC_REQUIRED) || !tdlen) 3890 return; 3891 e1000_flush_tx_ring(adapter); 3892 /* recheck, maybe the fault is caused by the rx ring */ 3893 pci_read_config_word(adapter->pdev, PCICFG_DESC_RING_STATUS, 3894 &hang_state); 3895 if (hang_state & FLUSH_DESC_REQUIRED) 3896 e1000_flush_rx_ring(adapter); 3897 } 3898 3899 /** 3900 * e1000e_systim_reset - reset the timesync registers after a hardware reset 3901 * @adapter: board private structure 3902 * 3903 * When the MAC is reset, all hardware bits for timesync will be reset to the 3904 * default values. This function will restore the settings last in place. 3905 * Since the clock SYSTIME registers are reset, we will simply restore the 3906 * cyclecounter to the kernel real clock time. 3907 **/ 3908 static void e1000e_systim_reset(struct e1000_adapter *adapter) 3909 { 3910 struct ptp_clock_info *info = &adapter->ptp_clock_info; 3911 struct e1000_hw *hw = &adapter->hw; 3912 unsigned long flags; 3913 u32 timinca; 3914 s32 ret_val; 3915 3916 if (!(adapter->flags & FLAG_HAS_HW_TIMESTAMP)) 3917 return; 3918 3919 if (info->adjfine) { 3920 /* restore the previous ptp frequency delta */ 3921 ret_val = info->adjfine(info, adapter->ptp_delta); 3922 } else { 3923 /* set the default base frequency if no adjustment possible */ 3924 ret_val = e1000e_get_base_timinca(adapter, &timinca); 3925 if (!ret_val) 3926 ew32(TIMINCA, timinca); 3927 } 3928 3929 if (ret_val) { 3930 dev_warn(&adapter->pdev->dev, 3931 "Failed to restore TIMINCA clock rate delta: %d\n", 3932 ret_val); 3933 return; 3934 } 3935 3936 /* reset the systim ns time counter */ 3937 spin_lock_irqsave(&adapter->systim_lock, flags); 3938 timecounter_init(&adapter->tc, &adapter->cc, 3939 ktime_to_ns(ktime_get_real())); 3940 spin_unlock_irqrestore(&adapter->systim_lock, flags); 3941 3942 /* restore the previous hwtstamp configuration settings */ 3943 e1000e_config_hwtstamp(adapter, &adapter->hwtstamp_config); 3944 } 3945 3946 /** 3947 * e1000e_reset - bring the hardware into a known good state 3948 * @adapter: board private structure 3949 * 3950 * This function boots the hardware and enables some settings that 3951 * require a configuration cycle of the hardware - those cannot be 3952 * set/changed during runtime. After reset the device needs to be 3953 * properly configured for Rx, Tx etc. 3954 */ 3955 void e1000e_reset(struct e1000_adapter *adapter) 3956 { 3957 struct e1000_mac_info *mac = &adapter->hw.mac; 3958 struct e1000_fc_info *fc = &adapter->hw.fc; 3959 struct e1000_hw *hw = &adapter->hw; 3960 u32 tx_space, min_tx_space, min_rx_space; 3961 u32 pba = adapter->pba; 3962 u16 hwm; 3963 3964 /* reset Packet Buffer Allocation to default */ 3965 ew32(PBA, pba); 3966 3967 if (adapter->max_frame_size > (VLAN_ETH_FRAME_LEN + ETH_FCS_LEN)) { 3968 /* To maintain wire speed transmits, the Tx FIFO should be 3969 * large enough to accommodate two full transmit packets, 3970 * rounded up to the next 1KB and expressed in KB. Likewise, 3971 * the Rx FIFO should be large enough to accommodate at least 3972 * one full receive packet and is similarly rounded up and 3973 * expressed in KB. 3974 */ 3975 pba = er32(PBA); 3976 /* upper 16 bits has Tx packet buffer allocation size in KB */ 3977 tx_space = pba >> 16; 3978 /* lower 16 bits has Rx packet buffer allocation size in KB */ 3979 pba &= 0xffff; 3980 /* the Tx fifo also stores 16 bytes of information about the Tx 3981 * but don't include ethernet FCS because hardware appends it 3982 */ 3983 min_tx_space = (adapter->max_frame_size + 3984 sizeof(struct e1000_tx_desc) - ETH_FCS_LEN) * 2; 3985 min_tx_space = ALIGN(min_tx_space, 1024); 3986 min_tx_space >>= 10; 3987 /* software strips receive CRC, so leave room for it */ 3988 min_rx_space = adapter->max_frame_size; 3989 min_rx_space = ALIGN(min_rx_space, 1024); 3990 min_rx_space >>= 10; 3991 3992 /* If current Tx allocation is less than the min Tx FIFO size, 3993 * and the min Tx FIFO size is less than the current Rx FIFO 3994 * allocation, take space away from current Rx allocation 3995 */ 3996 if ((tx_space < min_tx_space) && 3997 ((min_tx_space - tx_space) < pba)) { 3998 pba -= min_tx_space - tx_space; 3999 4000 /* if short on Rx space, Rx wins and must trump Tx 4001 * adjustment 4002 */ 4003 if (pba < min_rx_space) 4004 pba = min_rx_space; 4005 } 4006 4007 ew32(PBA, pba); 4008 } 4009 4010 /* flow control settings 4011 * 4012 * The high water mark must be low enough to fit one full frame 4013 * (or the size used for early receive) above it in the Rx FIFO. 4014 * Set it to the lower of: 4015 * - 90% of the Rx FIFO size, and 4016 * - the full Rx FIFO size minus one full frame 4017 */ 4018 if (adapter->flags & FLAG_DISABLE_FC_PAUSE_TIME) 4019 fc->pause_time = 0xFFFF; 4020 else 4021 fc->pause_time = E1000_FC_PAUSE_TIME; 4022 fc->send_xon = true; 4023 fc->current_mode = fc->requested_mode; 4024 4025 switch (hw->mac.type) { 4026 case e1000_ich9lan: 4027 case e1000_ich10lan: 4028 if (adapter->netdev->mtu > ETH_DATA_LEN) { 4029 pba = 14; 4030 ew32(PBA, pba); 4031 fc->high_water = 0x2800; 4032 fc->low_water = fc->high_water - 8; 4033 break; 4034 } 4035 fallthrough; 4036 default: 4037 hwm = min(((pba << 10) * 9 / 10), 4038 ((pba << 10) - adapter->max_frame_size)); 4039 4040 fc->high_water = hwm & E1000_FCRTH_RTH; /* 8-byte granularity */ 4041 fc->low_water = fc->high_water - 8; 4042 break; 4043 case e1000_pchlan: 4044 /* Workaround PCH LOM adapter hangs with certain network 4045 * loads. If hangs persist, try disabling Tx flow control. 4046 */ 4047 if (adapter->netdev->mtu > ETH_DATA_LEN) { 4048 fc->high_water = 0x3500; 4049 fc->low_water = 0x1500; 4050 } else { 4051 fc->high_water = 0x5000; 4052 fc->low_water = 0x3000; 4053 } 4054 fc->refresh_time = 0x1000; 4055 break; 4056 case e1000_pch2lan: 4057 case e1000_pch_lpt: 4058 case e1000_pch_spt: 4059 case e1000_pch_cnp: 4060 case e1000_pch_tgp: 4061 case e1000_pch_adp: 4062 case e1000_pch_mtp: 4063 case e1000_pch_lnp: 4064 case e1000_pch_ptp: 4065 fc->refresh_time = 0xFFFF; 4066 fc->pause_time = 0xFFFF; 4067 4068 if (adapter->netdev->mtu <= ETH_DATA_LEN) { 4069 fc->high_water = 0x05C20; 4070 fc->low_water = 0x05048; 4071 break; 4072 } 4073 4074 pba = 14; 4075 ew32(PBA, pba); 4076 fc->high_water = ((pba << 10) * 9 / 10) & E1000_FCRTH_RTH; 4077 fc->low_water = ((pba << 10) * 8 / 10) & E1000_FCRTL_RTL; 4078 break; 4079 } 4080 4081 /* Alignment of Tx data is on an arbitrary byte boundary with the 4082 * maximum size per Tx descriptor limited only to the transmit 4083 * allocation of the packet buffer minus 96 bytes with an upper 4084 * limit of 24KB due to receive synchronization limitations. 4085 */ 4086 adapter->tx_fifo_limit = min_t(u32, ((er32(PBA) >> 16) << 10) - 96, 4087 24 << 10); 4088 4089 /* Disable Adaptive Interrupt Moderation if 2 full packets cannot 4090 * fit in receive buffer. 4091 */ 4092 if (adapter->itr_setting & 0x3) { 4093 if ((adapter->max_frame_size * 2) > (pba << 10)) { 4094 if (!(adapter->flags2 & FLAG2_DISABLE_AIM)) { 4095 dev_info(&adapter->pdev->dev, 4096 "Interrupt Throttle Rate off\n"); 4097 adapter->flags2 |= FLAG2_DISABLE_AIM; 4098 e1000e_write_itr(adapter, 0); 4099 } 4100 } else if (adapter->flags2 & FLAG2_DISABLE_AIM) { 4101 dev_info(&adapter->pdev->dev, 4102 "Interrupt Throttle Rate on\n"); 4103 adapter->flags2 &= ~FLAG2_DISABLE_AIM; 4104 adapter->itr = 20000; 4105 e1000e_write_itr(adapter, adapter->itr); 4106 } 4107 } 4108 4109 if (hw->mac.type >= e1000_pch_spt) 4110 e1000_flush_desc_rings(adapter); 4111 /* Allow time for pending master requests to run */ 4112 mac->ops.reset_hw(hw); 4113 4114 /* For parts with AMT enabled, let the firmware know 4115 * that the network interface is in control 4116 */ 4117 if (adapter->flags & FLAG_HAS_AMT) 4118 e1000e_get_hw_control(adapter); 4119 4120 ew32(WUC, 0); 4121 4122 if (mac->ops.init_hw(hw)) 4123 e_err("Hardware Error\n"); 4124 4125 e1000_update_mng_vlan(adapter); 4126 4127 /* Enable h/w to recognize an 802.1Q VLAN Ethernet packet */ 4128 ew32(VET, ETH_P_8021Q); 4129 4130 e1000e_reset_adaptive(hw); 4131 4132 /* restore systim and hwtstamp settings */ 4133 e1000e_systim_reset(adapter); 4134 4135 /* Set EEE advertisement as appropriate */ 4136 if (adapter->flags2 & FLAG2_HAS_EEE) { 4137 s32 ret_val; 4138 u16 adv_addr; 4139 4140 switch (hw->phy.type) { 4141 case e1000_phy_82579: 4142 adv_addr = I82579_EEE_ADVERTISEMENT; 4143 break; 4144 case e1000_phy_i217: 4145 adv_addr = I217_EEE_ADVERTISEMENT; 4146 break; 4147 default: 4148 dev_err(&adapter->pdev->dev, 4149 "Invalid PHY type setting EEE advertisement\n"); 4150 return; 4151 } 4152 4153 ret_val = hw->phy.ops.acquire(hw); 4154 if (ret_val) { 4155 dev_err(&adapter->pdev->dev, 4156 "EEE advertisement - unable to acquire PHY\n"); 4157 return; 4158 } 4159 4160 e1000_write_emi_reg_locked(hw, adv_addr, 4161 hw->dev_spec.ich8lan.eee_disable ? 4162 0 : adapter->eee_advert); 4163 4164 hw->phy.ops.release(hw); 4165 } 4166 4167 if (!netif_running(adapter->netdev) && 4168 !test_bit(__E1000_TESTING, &adapter->state)) 4169 e1000_power_down_phy(adapter); 4170 4171 e1000_get_phy_info(hw); 4172 4173 if ((adapter->flags & FLAG_HAS_SMART_POWER_DOWN) && 4174 !(adapter->flags & FLAG_SMART_POWER_DOWN)) { 4175 u16 phy_data = 0; 4176 /* speed up time to link by disabling smart power down, ignore 4177 * the return value of this function because there is nothing 4178 * different we would do if it failed 4179 */ 4180 e1e_rphy(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data); 4181 phy_data &= ~IGP02E1000_PM_SPD; 4182 e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT, phy_data); 4183 } 4184 if (hw->mac.type >= e1000_pch_spt && adapter->int_mode == 0) { 4185 u32 reg; 4186 4187 /* Fextnvm7 @ 0xe4[2] = 1 */ 4188 reg = er32(FEXTNVM7); 4189 reg |= E1000_FEXTNVM7_SIDE_CLK_UNGATE; 4190 ew32(FEXTNVM7, reg); 4191 /* Fextnvm9 @ 0x5bb4[13:12] = 11 */ 4192 reg = er32(FEXTNVM9); 4193 reg |= E1000_FEXTNVM9_IOSFSB_CLKGATE_DIS | 4194 E1000_FEXTNVM9_IOSFSB_CLKREQ_DIS; 4195 ew32(FEXTNVM9, reg); 4196 } 4197 4198 } 4199 4200 /** 4201 * e1000e_trigger_lsc - trigger an LSC interrupt 4202 * @adapter: 4203 * 4204 * Fire a link status change interrupt to start the watchdog. 4205 **/ 4206 static void e1000e_trigger_lsc(struct e1000_adapter *adapter) 4207 { 4208 struct e1000_hw *hw = &adapter->hw; 4209 4210 if (adapter->msix_entries) 4211 ew32(ICS, E1000_ICS_LSC | E1000_ICS_OTHER); 4212 else 4213 ew32(ICS, E1000_ICS_LSC); 4214 } 4215 4216 void e1000e_up(struct e1000_adapter *adapter) 4217 { 4218 /* hardware has been reset, we need to reload some things */ 4219 e1000_configure(adapter); 4220 4221 clear_bit(__E1000_DOWN, &adapter->state); 4222 4223 if (adapter->msix_entries) 4224 e1000_configure_msix(adapter); 4225 e1000_irq_enable(adapter); 4226 4227 /* Tx queue started by watchdog timer when link is up */ 4228 4229 e1000e_trigger_lsc(adapter); 4230 } 4231 4232 static void e1000e_flush_descriptors(struct e1000_adapter *adapter) 4233 { 4234 struct e1000_hw *hw = &adapter->hw; 4235 4236 if (!(adapter->flags2 & FLAG2_DMA_BURST)) 4237 return; 4238 4239 /* flush pending descriptor writebacks to memory */ 4240 ew32(TIDV, adapter->tx_int_delay | E1000_TIDV_FPD); 4241 ew32(RDTR, adapter->rx_int_delay | E1000_RDTR_FPD); 4242 4243 /* execute the writes immediately */ 4244 e1e_flush(); 4245 4246 /* due to rare timing issues, write to TIDV/RDTR again to ensure the 4247 * write is successful 4248 */ 4249 ew32(TIDV, adapter->tx_int_delay | E1000_TIDV_FPD); 4250 ew32(RDTR, adapter->rx_int_delay | E1000_RDTR_FPD); 4251 4252 /* execute the writes immediately */ 4253 e1e_flush(); 4254 } 4255 4256 static void e1000e_update_stats(struct e1000_adapter *adapter); 4257 4258 /** 4259 * e1000e_down - quiesce the device and optionally reset the hardware 4260 * @adapter: board private structure 4261 * @reset: boolean flag to reset the hardware or not 4262 */ 4263 void e1000e_down(struct e1000_adapter *adapter, bool reset) 4264 { 4265 struct net_device *netdev = adapter->netdev; 4266 struct e1000_hw *hw = &adapter->hw; 4267 u32 tctl, rctl; 4268 4269 /* signal that we're down so the interrupt handler does not 4270 * reschedule our watchdog timer 4271 */ 4272 set_bit(__E1000_DOWN, &adapter->state); 4273 4274 netif_carrier_off(netdev); 4275 4276 /* disable receives in the hardware */ 4277 rctl = er32(RCTL); 4278 if (!(adapter->flags2 & FLAG2_NO_DISABLE_RX)) 4279 ew32(RCTL, rctl & ~E1000_RCTL_EN); 4280 /* flush and sleep below */ 4281 4282 netif_stop_queue(netdev); 4283 4284 /* disable transmits in the hardware */ 4285 tctl = er32(TCTL); 4286 tctl &= ~E1000_TCTL_EN; 4287 ew32(TCTL, tctl); 4288 4289 /* flush both disables and wait for them to finish */ 4290 e1e_flush(); 4291 usleep_range(10000, 11000); 4292 4293 e1000_irq_disable(adapter); 4294 4295 napi_synchronize(&adapter->napi); 4296 4297 del_timer_sync(&adapter->watchdog_timer); 4298 del_timer_sync(&adapter->phy_info_timer); 4299 4300 spin_lock(&adapter->stats64_lock); 4301 e1000e_update_stats(adapter); 4302 spin_unlock(&adapter->stats64_lock); 4303 4304 e1000e_flush_descriptors(adapter); 4305 4306 adapter->link_speed = 0; 4307 adapter->link_duplex = 0; 4308 4309 /* Disable Si errata workaround on PCHx for jumbo frame flow */ 4310 if ((hw->mac.type >= e1000_pch2lan) && 4311 (adapter->netdev->mtu > ETH_DATA_LEN) && 4312 e1000_lv_jumbo_workaround_ich8lan(hw, false)) 4313 e_dbg("failed to disable jumbo frame workaround mode\n"); 4314 4315 if (!pci_channel_offline(adapter->pdev)) { 4316 if (reset) 4317 e1000e_reset(adapter); 4318 else if (hw->mac.type >= e1000_pch_spt) 4319 e1000_flush_desc_rings(adapter); 4320 } 4321 e1000_clean_tx_ring(adapter->tx_ring); 4322 e1000_clean_rx_ring(adapter->rx_ring); 4323 } 4324 4325 void e1000e_reinit_locked(struct e1000_adapter *adapter) 4326 { 4327 might_sleep(); 4328 while (test_and_set_bit(__E1000_RESETTING, &adapter->state)) 4329 usleep_range(1000, 1100); 4330 e1000e_down(adapter, true); 4331 e1000e_up(adapter); 4332 clear_bit(__E1000_RESETTING, &adapter->state); 4333 } 4334 4335 /** 4336 * e1000e_sanitize_systim - sanitize raw cycle counter reads 4337 * @hw: pointer to the HW structure 4338 * @systim: PHC time value read, sanitized and returned 4339 * @sts: structure to hold system time before and after reading SYSTIML, 4340 * may be NULL 4341 * 4342 * Errata for 82574/82583 possible bad bits read from SYSTIMH/L: 4343 * check to see that the time is incrementing at a reasonable 4344 * rate and is a multiple of incvalue. 4345 **/ 4346 static u64 e1000e_sanitize_systim(struct e1000_hw *hw, u64 systim, 4347 struct ptp_system_timestamp *sts) 4348 { 4349 u64 time_delta, rem, temp; 4350 u64 systim_next; 4351 u32 incvalue; 4352 int i; 4353 4354 incvalue = er32(TIMINCA) & E1000_TIMINCA_INCVALUE_MASK; 4355 for (i = 0; i < E1000_MAX_82574_SYSTIM_REREADS; i++) { 4356 /* latch SYSTIMH on read of SYSTIML */ 4357 ptp_read_system_prets(sts); 4358 systim_next = (u64)er32(SYSTIML); 4359 ptp_read_system_postts(sts); 4360 systim_next |= (u64)er32(SYSTIMH) << 32; 4361 4362 time_delta = systim_next - systim; 4363 temp = time_delta; 4364 /* VMWare users have seen incvalue of zero, don't div / 0 */ 4365 rem = incvalue ? do_div(temp, incvalue) : (time_delta != 0); 4366 4367 systim = systim_next; 4368 4369 if ((time_delta < E1000_82574_SYSTIM_EPSILON) && (rem == 0)) 4370 break; 4371 } 4372 4373 return systim; 4374 } 4375 4376 /** 4377 * e1000e_read_systim - read SYSTIM register 4378 * @adapter: board private structure 4379 * @sts: structure which will contain system time before and after reading 4380 * SYSTIML, may be NULL 4381 **/ 4382 u64 e1000e_read_systim(struct e1000_adapter *adapter, 4383 struct ptp_system_timestamp *sts) 4384 { 4385 struct e1000_hw *hw = &adapter->hw; 4386 u32 systimel, systimel_2, systimeh; 4387 u64 systim; 4388 /* SYSTIMH latching upon SYSTIML read does not work well. 4389 * This means that if SYSTIML overflows after we read it but before 4390 * we read SYSTIMH, the value of SYSTIMH has been incremented and we 4391 * will experience a huge non linear increment in the systime value 4392 * to fix that we test for overflow and if true, we re-read systime. 4393 */ 4394 ptp_read_system_prets(sts); 4395 systimel = er32(SYSTIML); 4396 ptp_read_system_postts(sts); 4397 systimeh = er32(SYSTIMH); 4398 /* Is systimel is so large that overflow is possible? */ 4399 if (systimel >= (u32)0xffffffff - E1000_TIMINCA_INCVALUE_MASK) { 4400 ptp_read_system_prets(sts); 4401 systimel_2 = er32(SYSTIML); 4402 ptp_read_system_postts(sts); 4403 if (systimel > systimel_2) { 4404 /* There was an overflow, read again SYSTIMH, and use 4405 * systimel_2 4406 */ 4407 systimeh = er32(SYSTIMH); 4408 systimel = systimel_2; 4409 } 4410 } 4411 systim = (u64)systimel; 4412 systim |= (u64)systimeh << 32; 4413 4414 if (adapter->flags2 & FLAG2_CHECK_SYSTIM_OVERFLOW) 4415 systim = e1000e_sanitize_systim(hw, systim, sts); 4416 4417 return systim; 4418 } 4419 4420 /** 4421 * e1000e_cyclecounter_read - read raw cycle counter (used by time counter) 4422 * @cc: cyclecounter structure 4423 **/ 4424 static u64 e1000e_cyclecounter_read(const struct cyclecounter *cc) 4425 { 4426 struct e1000_adapter *adapter = container_of(cc, struct e1000_adapter, 4427 cc); 4428 4429 return e1000e_read_systim(adapter, NULL); 4430 } 4431 4432 /** 4433 * e1000_sw_init - Initialize general software structures (struct e1000_adapter) 4434 * @adapter: board private structure to initialize 4435 * 4436 * e1000_sw_init initializes the Adapter private data structure. 4437 * Fields are initialized based on PCI device information and 4438 * OS network device settings (MTU size). 4439 **/ 4440 static int e1000_sw_init(struct e1000_adapter *adapter) 4441 { 4442 struct net_device *netdev = adapter->netdev; 4443 4444 adapter->rx_buffer_len = VLAN_ETH_FRAME_LEN + ETH_FCS_LEN; 4445 adapter->rx_ps_bsize0 = 128; 4446 adapter->max_frame_size = netdev->mtu + VLAN_ETH_HLEN + ETH_FCS_LEN; 4447 adapter->min_frame_size = ETH_ZLEN + ETH_FCS_LEN; 4448 adapter->tx_ring_count = E1000_DEFAULT_TXD; 4449 adapter->rx_ring_count = E1000_DEFAULT_RXD; 4450 4451 spin_lock_init(&adapter->stats64_lock); 4452 4453 e1000e_set_interrupt_capability(adapter); 4454 4455 if (e1000_alloc_queues(adapter)) 4456 return -ENOMEM; 4457 4458 /* Setup hardware time stamping cyclecounter */ 4459 if (adapter->flags & FLAG_HAS_HW_TIMESTAMP) { 4460 adapter->cc.read = e1000e_cyclecounter_read; 4461 adapter->cc.mask = CYCLECOUNTER_MASK(64); 4462 adapter->cc.mult = 1; 4463 /* cc.shift set in e1000e_get_base_tininca() */ 4464 4465 spin_lock_init(&adapter->systim_lock); 4466 INIT_WORK(&adapter->tx_hwtstamp_work, e1000e_tx_hwtstamp_work); 4467 } 4468 4469 /* Explicitly disable IRQ since the NIC can be in any state. */ 4470 e1000_irq_disable(adapter); 4471 4472 set_bit(__E1000_DOWN, &adapter->state); 4473 return 0; 4474 } 4475 4476 /** 4477 * e1000_intr_msi_test - Interrupt Handler 4478 * @irq: interrupt number 4479 * @data: pointer to a network interface device structure 4480 **/ 4481 static irqreturn_t e1000_intr_msi_test(int __always_unused irq, void *data) 4482 { 4483 struct net_device *netdev = data; 4484 struct e1000_adapter *adapter = netdev_priv(netdev); 4485 struct e1000_hw *hw = &adapter->hw; 4486 u32 icr = er32(ICR); 4487 4488 e_dbg("icr is %08X\n", icr); 4489 if (icr & E1000_ICR_RXSEQ) { 4490 adapter->flags &= ~FLAG_MSI_TEST_FAILED; 4491 /* Force memory writes to complete before acknowledging the 4492 * interrupt is handled. 4493 */ 4494 wmb(); 4495 } 4496 4497 return IRQ_HANDLED; 4498 } 4499 4500 /** 4501 * e1000_test_msi_interrupt - Returns 0 for successful test 4502 * @adapter: board private struct 4503 * 4504 * code flow taken from tg3.c 4505 **/ 4506 static int e1000_test_msi_interrupt(struct e1000_adapter *adapter) 4507 { 4508 struct net_device *netdev = adapter->netdev; 4509 struct e1000_hw *hw = &adapter->hw; 4510 int err; 4511 4512 /* poll_enable hasn't been called yet, so don't need disable */ 4513 /* clear any pending events */ 4514 er32(ICR); 4515 4516 /* free the real vector and request a test handler */ 4517 e1000_free_irq(adapter); 4518 e1000e_reset_interrupt_capability(adapter); 4519 4520 /* Assume that the test fails, if it succeeds then the test 4521 * MSI irq handler will unset this flag 4522 */ 4523 adapter->flags |= FLAG_MSI_TEST_FAILED; 4524 4525 err = pci_enable_msi(adapter->pdev); 4526 if (err) 4527 goto msi_test_failed; 4528 4529 err = request_irq(adapter->pdev->irq, e1000_intr_msi_test, 0, 4530 netdev->name, netdev); 4531 if (err) { 4532 pci_disable_msi(adapter->pdev); 4533 goto msi_test_failed; 4534 } 4535 4536 /* Force memory writes to complete before enabling and firing an 4537 * interrupt. 4538 */ 4539 wmb(); 4540 4541 e1000_irq_enable(adapter); 4542 4543 /* fire an unusual interrupt on the test handler */ 4544 ew32(ICS, E1000_ICS_RXSEQ); 4545 e1e_flush(); 4546 msleep(100); 4547 4548 e1000_irq_disable(adapter); 4549 4550 rmb(); /* read flags after interrupt has been fired */ 4551 4552 if (adapter->flags & FLAG_MSI_TEST_FAILED) { 4553 adapter->int_mode = E1000E_INT_MODE_LEGACY; 4554 e_info("MSI interrupt test failed, using legacy interrupt.\n"); 4555 } else { 4556 e_dbg("MSI interrupt test succeeded!\n"); 4557 } 4558 4559 free_irq(adapter->pdev->irq, netdev); 4560 pci_disable_msi(adapter->pdev); 4561 4562 msi_test_failed: 4563 e1000e_set_interrupt_capability(adapter); 4564 return e1000_request_irq(adapter); 4565 } 4566 4567 /** 4568 * e1000_test_msi - Returns 0 if MSI test succeeds or INTx mode is restored 4569 * @adapter: board private struct 4570 * 4571 * code flow taken from tg3.c, called with e1000 interrupts disabled. 4572 **/ 4573 static int e1000_test_msi(struct e1000_adapter *adapter) 4574 { 4575 int err; 4576 u16 pci_cmd; 4577 4578 if (!(adapter->flags & FLAG_MSI_ENABLED)) 4579 return 0; 4580 4581 /* disable SERR in case the MSI write causes a master abort */ 4582 pci_read_config_word(adapter->pdev, PCI_COMMAND, &pci_cmd); 4583 if (pci_cmd & PCI_COMMAND_SERR) 4584 pci_write_config_word(adapter->pdev, PCI_COMMAND, 4585 pci_cmd & ~PCI_COMMAND_SERR); 4586 4587 err = e1000_test_msi_interrupt(adapter); 4588 4589 /* re-enable SERR */ 4590 if (pci_cmd & PCI_COMMAND_SERR) { 4591 pci_read_config_word(adapter->pdev, PCI_COMMAND, &pci_cmd); 4592 pci_cmd |= PCI_COMMAND_SERR; 4593 pci_write_config_word(adapter->pdev, PCI_COMMAND, pci_cmd); 4594 } 4595 4596 return err; 4597 } 4598 4599 /** 4600 * e1000e_open - Called when a network interface is made active 4601 * @netdev: network interface device structure 4602 * 4603 * Returns 0 on success, negative value on failure 4604 * 4605 * The open entry point is called when a network interface is made 4606 * active by the system (IFF_UP). At this point all resources needed 4607 * for transmit and receive operations are allocated, the interrupt 4608 * handler is registered with the OS, the watchdog timer is started, 4609 * and the stack is notified that the interface is ready. 4610 **/ 4611 int e1000e_open(struct net_device *netdev) 4612 { 4613 struct e1000_adapter *adapter = netdev_priv(netdev); 4614 struct e1000_hw *hw = &adapter->hw; 4615 struct pci_dev *pdev = adapter->pdev; 4616 int err; 4617 4618 /* disallow open during test */ 4619 if (test_bit(__E1000_TESTING, &adapter->state)) 4620 return -EBUSY; 4621 4622 pm_runtime_get_sync(&pdev->dev); 4623 4624 netif_carrier_off(netdev); 4625 netif_stop_queue(netdev); 4626 4627 /* allocate transmit descriptors */ 4628 err = e1000e_setup_tx_resources(adapter->tx_ring); 4629 if (err) 4630 goto err_setup_tx; 4631 4632 /* allocate receive descriptors */ 4633 err = e1000e_setup_rx_resources(adapter->rx_ring); 4634 if (err) 4635 goto err_setup_rx; 4636 4637 /* If AMT is enabled, let the firmware know that the network 4638 * interface is now open and reset the part to a known state. 4639 */ 4640 if (adapter->flags & FLAG_HAS_AMT) { 4641 e1000e_get_hw_control(adapter); 4642 e1000e_reset(adapter); 4643 } 4644 4645 e1000e_power_up_phy(adapter); 4646 4647 adapter->mng_vlan_id = E1000_MNG_VLAN_NONE; 4648 if ((adapter->hw.mng_cookie.status & E1000_MNG_DHCP_COOKIE_STATUS_VLAN)) 4649 e1000_update_mng_vlan(adapter); 4650 4651 /* DMA latency requirement to workaround jumbo issue */ 4652 cpu_latency_qos_add_request(&adapter->pm_qos_req, PM_QOS_DEFAULT_VALUE); 4653 4654 /* before we allocate an interrupt, we must be ready to handle it. 4655 * Setting DEBUG_SHIRQ in the kernel makes it fire an interrupt 4656 * as soon as we call pci_request_irq, so we have to setup our 4657 * clean_rx handler before we do so. 4658 */ 4659 e1000_configure(adapter); 4660 4661 err = e1000_request_irq(adapter); 4662 if (err) 4663 goto err_req_irq; 4664 4665 /* Work around PCIe errata with MSI interrupts causing some chipsets to 4666 * ignore e1000e MSI messages, which means we need to test our MSI 4667 * interrupt now 4668 */ 4669 if (adapter->int_mode != E1000E_INT_MODE_LEGACY) { 4670 err = e1000_test_msi(adapter); 4671 if (err) { 4672 e_err("Interrupt allocation failed\n"); 4673 goto err_req_irq; 4674 } 4675 } 4676 4677 /* From here on the code is the same as e1000e_up() */ 4678 clear_bit(__E1000_DOWN, &adapter->state); 4679 4680 napi_enable(&adapter->napi); 4681 4682 e1000_irq_enable(adapter); 4683 4684 adapter->tx_hang_recheck = false; 4685 4686 hw->mac.get_link_status = true; 4687 pm_runtime_put(&pdev->dev); 4688 4689 e1000e_trigger_lsc(adapter); 4690 4691 return 0; 4692 4693 err_req_irq: 4694 cpu_latency_qos_remove_request(&adapter->pm_qos_req); 4695 e1000e_release_hw_control(adapter); 4696 e1000_power_down_phy(adapter); 4697 e1000e_free_rx_resources(adapter->rx_ring); 4698 err_setup_rx: 4699 e1000e_free_tx_resources(adapter->tx_ring); 4700 err_setup_tx: 4701 e1000e_reset(adapter); 4702 pm_runtime_put_sync(&pdev->dev); 4703 4704 return err; 4705 } 4706 4707 /** 4708 * e1000e_close - Disables a network interface 4709 * @netdev: network interface device structure 4710 * 4711 * Returns 0, this is not allowed to fail 4712 * 4713 * The close entry point is called when an interface is de-activated 4714 * by the OS. The hardware is still under the drivers control, but 4715 * needs to be disabled. A global MAC reset is issued to stop the 4716 * hardware, and all transmit and receive resources are freed. 4717 **/ 4718 int e1000e_close(struct net_device *netdev) 4719 { 4720 struct e1000_adapter *adapter = netdev_priv(netdev); 4721 struct pci_dev *pdev = adapter->pdev; 4722 int count = E1000_CHECK_RESET_COUNT; 4723 4724 while (test_bit(__E1000_RESETTING, &adapter->state) && count--) 4725 usleep_range(10000, 11000); 4726 4727 WARN_ON(test_bit(__E1000_RESETTING, &adapter->state)); 4728 4729 pm_runtime_get_sync(&pdev->dev); 4730 4731 if (netif_device_present(netdev)) { 4732 e1000e_down(adapter, true); 4733 e1000_free_irq(adapter); 4734 4735 /* Link status message must follow this format */ 4736 netdev_info(netdev, "NIC Link is Down\n"); 4737 } 4738 4739 napi_disable(&adapter->napi); 4740 4741 e1000e_free_tx_resources(adapter->tx_ring); 4742 e1000e_free_rx_resources(adapter->rx_ring); 4743 4744 /* kill manageability vlan ID if supported, but not if a vlan with 4745 * the same ID is registered on the host OS (let 8021q kill it) 4746 */ 4747 if (adapter->hw.mng_cookie.status & E1000_MNG_DHCP_COOKIE_STATUS_VLAN) 4748 e1000_vlan_rx_kill_vid(netdev, htons(ETH_P_8021Q), 4749 adapter->mng_vlan_id); 4750 4751 /* If AMT is enabled, let the firmware know that the network 4752 * interface is now closed 4753 */ 4754 if ((adapter->flags & FLAG_HAS_AMT) && 4755 !test_bit(__E1000_TESTING, &adapter->state)) 4756 e1000e_release_hw_control(adapter); 4757 4758 cpu_latency_qos_remove_request(&adapter->pm_qos_req); 4759 4760 pm_runtime_put_sync(&pdev->dev); 4761 4762 return 0; 4763 } 4764 4765 /** 4766 * e1000_set_mac - Change the Ethernet Address of the NIC 4767 * @netdev: network interface device structure 4768 * @p: pointer to an address structure 4769 * 4770 * Returns 0 on success, negative on failure 4771 **/ 4772 static int e1000_set_mac(struct net_device *netdev, void *p) 4773 { 4774 struct e1000_adapter *adapter = netdev_priv(netdev); 4775 struct e1000_hw *hw = &adapter->hw; 4776 struct sockaddr *addr = p; 4777 4778 if (!is_valid_ether_addr(addr->sa_data)) 4779 return -EADDRNOTAVAIL; 4780 4781 eth_hw_addr_set(netdev, addr->sa_data); 4782 memcpy(adapter->hw.mac.addr, addr->sa_data, netdev->addr_len); 4783 4784 hw->mac.ops.rar_set(&adapter->hw, adapter->hw.mac.addr, 0); 4785 4786 if (adapter->flags & FLAG_RESET_OVERWRITES_LAA) { 4787 /* activate the work around */ 4788 e1000e_set_laa_state_82571(&adapter->hw, 1); 4789 4790 /* Hold a copy of the LAA in RAR[14] This is done so that 4791 * between the time RAR[0] gets clobbered and the time it 4792 * gets fixed (in e1000_watchdog), the actual LAA is in one 4793 * of the RARs and no incoming packets directed to this port 4794 * are dropped. Eventually the LAA will be in RAR[0] and 4795 * RAR[14] 4796 */ 4797 hw->mac.ops.rar_set(&adapter->hw, adapter->hw.mac.addr, 4798 adapter->hw.mac.rar_entry_count - 1); 4799 } 4800 4801 return 0; 4802 } 4803 4804 /** 4805 * e1000e_update_phy_task - work thread to update phy 4806 * @work: pointer to our work struct 4807 * 4808 * this worker thread exists because we must acquire a 4809 * semaphore to read the phy, which we could msleep while 4810 * waiting for it, and we can't msleep in a timer. 4811 **/ 4812 static void e1000e_update_phy_task(struct work_struct *work) 4813 { 4814 struct e1000_adapter *adapter = container_of(work, 4815 struct e1000_adapter, 4816 update_phy_task); 4817 struct e1000_hw *hw = &adapter->hw; 4818 4819 if (test_bit(__E1000_DOWN, &adapter->state)) 4820 return; 4821 4822 e1000_get_phy_info(hw); 4823 4824 /* Enable EEE on 82579 after link up */ 4825 if (hw->phy.type >= e1000_phy_82579) 4826 e1000_set_eee_pchlan(hw); 4827 } 4828 4829 /** 4830 * e1000_update_phy_info - timre call-back to update PHY info 4831 * @t: pointer to timer_list containing private info adapter 4832 * 4833 * Need to wait a few seconds after link up to get diagnostic information from 4834 * the phy 4835 **/ 4836 static void e1000_update_phy_info(struct timer_list *t) 4837 { 4838 struct e1000_adapter *adapter = from_timer(adapter, t, phy_info_timer); 4839 4840 if (test_bit(__E1000_DOWN, &adapter->state)) 4841 return; 4842 4843 schedule_work(&adapter->update_phy_task); 4844 } 4845 4846 /** 4847 * e1000e_update_phy_stats - Update the PHY statistics counters 4848 * @adapter: board private structure 4849 * 4850 * Read/clear the upper 16-bit PHY registers and read/accumulate lower 4851 **/ 4852 static void e1000e_update_phy_stats(struct e1000_adapter *adapter) 4853 { 4854 struct e1000_hw *hw = &adapter->hw; 4855 s32 ret_val; 4856 u16 phy_data; 4857 4858 ret_val = hw->phy.ops.acquire(hw); 4859 if (ret_val) 4860 return; 4861 4862 /* A page set is expensive so check if already on desired page. 4863 * If not, set to the page with the PHY status registers. 4864 */ 4865 hw->phy.addr = 1; 4866 ret_val = e1000e_read_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT, 4867 &phy_data); 4868 if (ret_val) 4869 goto release; 4870 if (phy_data != (HV_STATS_PAGE << IGP_PAGE_SHIFT)) { 4871 ret_val = hw->phy.ops.set_page(hw, 4872 HV_STATS_PAGE << IGP_PAGE_SHIFT); 4873 if (ret_val) 4874 goto release; 4875 } 4876 4877 /* Single Collision Count */ 4878 hw->phy.ops.read_reg_page(hw, HV_SCC_UPPER, &phy_data); 4879 ret_val = hw->phy.ops.read_reg_page(hw, HV_SCC_LOWER, &phy_data); 4880 if (!ret_val) 4881 adapter->stats.scc += phy_data; 4882 4883 /* Excessive Collision Count */ 4884 hw->phy.ops.read_reg_page(hw, HV_ECOL_UPPER, &phy_data); 4885 ret_val = hw->phy.ops.read_reg_page(hw, HV_ECOL_LOWER, &phy_data); 4886 if (!ret_val) 4887 adapter->stats.ecol += phy_data; 4888 4889 /* Multiple Collision Count */ 4890 hw->phy.ops.read_reg_page(hw, HV_MCC_UPPER, &phy_data); 4891 ret_val = hw->phy.ops.read_reg_page(hw, HV_MCC_LOWER, &phy_data); 4892 if (!ret_val) 4893 adapter->stats.mcc += phy_data; 4894 4895 /* Late Collision Count */ 4896 hw->phy.ops.read_reg_page(hw, HV_LATECOL_UPPER, &phy_data); 4897 ret_val = hw->phy.ops.read_reg_page(hw, HV_LATECOL_LOWER, &phy_data); 4898 if (!ret_val) 4899 adapter->stats.latecol += phy_data; 4900 4901 /* Collision Count - also used for adaptive IFS */ 4902 hw->phy.ops.read_reg_page(hw, HV_COLC_UPPER, &phy_data); 4903 ret_val = hw->phy.ops.read_reg_page(hw, HV_COLC_LOWER, &phy_data); 4904 if (!ret_val) 4905 hw->mac.collision_delta = phy_data; 4906 4907 /* Defer Count */ 4908 hw->phy.ops.read_reg_page(hw, HV_DC_UPPER, &phy_data); 4909 ret_val = hw->phy.ops.read_reg_page(hw, HV_DC_LOWER, &phy_data); 4910 if (!ret_val) 4911 adapter->stats.dc += phy_data; 4912 4913 /* Transmit with no CRS */ 4914 hw->phy.ops.read_reg_page(hw, HV_TNCRS_UPPER, &phy_data); 4915 ret_val = hw->phy.ops.read_reg_page(hw, HV_TNCRS_LOWER, &phy_data); 4916 if (!ret_val) 4917 adapter->stats.tncrs += phy_data; 4918 4919 release: 4920 hw->phy.ops.release(hw); 4921 } 4922 4923 /** 4924 * e1000e_update_stats - Update the board statistics counters 4925 * @adapter: board private structure 4926 **/ 4927 static void e1000e_update_stats(struct e1000_adapter *adapter) 4928 { 4929 struct net_device *netdev = adapter->netdev; 4930 struct e1000_hw *hw = &adapter->hw; 4931 struct pci_dev *pdev = adapter->pdev; 4932 4933 /* Prevent stats update while adapter is being reset, or if the pci 4934 * connection is down. 4935 */ 4936 if (adapter->link_speed == 0) 4937 return; 4938 if (pci_channel_offline(pdev)) 4939 return; 4940 4941 adapter->stats.crcerrs += er32(CRCERRS); 4942 adapter->stats.gprc += er32(GPRC); 4943 adapter->stats.gorc += er32(GORCL); 4944 er32(GORCH); /* Clear gorc */ 4945 adapter->stats.bprc += er32(BPRC); 4946 adapter->stats.mprc += er32(MPRC); 4947 adapter->stats.roc += er32(ROC); 4948 4949 adapter->stats.mpc += er32(MPC); 4950 4951 /* Half-duplex statistics */ 4952 if (adapter->link_duplex == HALF_DUPLEX) { 4953 if (adapter->flags2 & FLAG2_HAS_PHY_STATS) { 4954 e1000e_update_phy_stats(adapter); 4955 } else { 4956 adapter->stats.scc += er32(SCC); 4957 adapter->stats.ecol += er32(ECOL); 4958 adapter->stats.mcc += er32(MCC); 4959 adapter->stats.latecol += er32(LATECOL); 4960 adapter->stats.dc += er32(DC); 4961 4962 hw->mac.collision_delta = er32(COLC); 4963 4964 if ((hw->mac.type != e1000_82574) && 4965 (hw->mac.type != e1000_82583)) 4966 adapter->stats.tncrs += er32(TNCRS); 4967 } 4968 adapter->stats.colc += hw->mac.collision_delta; 4969 } 4970 4971 adapter->stats.xonrxc += er32(XONRXC); 4972 adapter->stats.xontxc += er32(XONTXC); 4973 adapter->stats.xoffrxc += er32(XOFFRXC); 4974 adapter->stats.xofftxc += er32(XOFFTXC); 4975 adapter->stats.gptc += er32(GPTC); 4976 adapter->stats.gotc += er32(GOTCL); 4977 er32(GOTCH); /* Clear gotc */ 4978 adapter->stats.rnbc += er32(RNBC); 4979 adapter->stats.ruc += er32(RUC); 4980 4981 adapter->stats.mptc += er32(MPTC); 4982 adapter->stats.bptc += er32(BPTC); 4983 4984 /* used for adaptive IFS */ 4985 4986 hw->mac.tx_packet_delta = er32(TPT); 4987 adapter->stats.tpt += hw->mac.tx_packet_delta; 4988 4989 adapter->stats.algnerrc += er32(ALGNERRC); 4990 adapter->stats.rxerrc += er32(RXERRC); 4991 adapter->stats.cexterr += er32(CEXTERR); 4992 adapter->stats.tsctc += er32(TSCTC); 4993 adapter->stats.tsctfc += er32(TSCTFC); 4994 4995 /* Fill out the OS statistics structure */ 4996 netdev->stats.multicast = adapter->stats.mprc; 4997 netdev->stats.collisions = adapter->stats.colc; 4998 4999 /* Rx Errors */ 5000 5001 /* RLEC on some newer hardware can be incorrect so build 5002 * our own version based on RUC and ROC 5003 */ 5004 netdev->stats.rx_errors = adapter->stats.rxerrc + 5005 adapter->stats.crcerrs + adapter->stats.algnerrc + 5006 adapter->stats.ruc + adapter->stats.roc + adapter->stats.cexterr; 5007 netdev->stats.rx_length_errors = adapter->stats.ruc + 5008 adapter->stats.roc; 5009 netdev->stats.rx_crc_errors = adapter->stats.crcerrs; 5010 netdev->stats.rx_frame_errors = adapter->stats.algnerrc; 5011 netdev->stats.rx_missed_errors = adapter->stats.mpc; 5012 5013 /* Tx Errors */ 5014 netdev->stats.tx_errors = adapter->stats.ecol + adapter->stats.latecol; 5015 netdev->stats.tx_aborted_errors = adapter->stats.ecol; 5016 netdev->stats.tx_window_errors = adapter->stats.latecol; 5017 netdev->stats.tx_carrier_errors = adapter->stats.tncrs; 5018 5019 /* Tx Dropped needs to be maintained elsewhere */ 5020 5021 /* Management Stats */ 5022 adapter->stats.mgptc += er32(MGTPTC); 5023 adapter->stats.mgprc += er32(MGTPRC); 5024 adapter->stats.mgpdc += er32(MGTPDC); 5025 5026 /* Correctable ECC Errors */ 5027 if (hw->mac.type >= e1000_pch_lpt) { 5028 u32 pbeccsts = er32(PBECCSTS); 5029 5030 adapter->corr_errors += 5031 pbeccsts & E1000_PBECCSTS_CORR_ERR_CNT_MASK; 5032 adapter->uncorr_errors += 5033 (pbeccsts & E1000_PBECCSTS_UNCORR_ERR_CNT_MASK) >> 5034 E1000_PBECCSTS_UNCORR_ERR_CNT_SHIFT; 5035 } 5036 } 5037 5038 /** 5039 * e1000_phy_read_status - Update the PHY register status snapshot 5040 * @adapter: board private structure 5041 **/ 5042 static void e1000_phy_read_status(struct e1000_adapter *adapter) 5043 { 5044 struct e1000_hw *hw = &adapter->hw; 5045 struct e1000_phy_regs *phy = &adapter->phy_regs; 5046 5047 if (!pm_runtime_suspended((&adapter->pdev->dev)->parent) && 5048 (er32(STATUS) & E1000_STATUS_LU) && 5049 (adapter->hw.phy.media_type == e1000_media_type_copper)) { 5050 int ret_val; 5051 5052 ret_val = e1e_rphy(hw, MII_BMCR, &phy->bmcr); 5053 ret_val |= e1e_rphy(hw, MII_BMSR, &phy->bmsr); 5054 ret_val |= e1e_rphy(hw, MII_ADVERTISE, &phy->advertise); 5055 ret_val |= e1e_rphy(hw, MII_LPA, &phy->lpa); 5056 ret_val |= e1e_rphy(hw, MII_EXPANSION, &phy->expansion); 5057 ret_val |= e1e_rphy(hw, MII_CTRL1000, &phy->ctrl1000); 5058 ret_val |= e1e_rphy(hw, MII_STAT1000, &phy->stat1000); 5059 ret_val |= e1e_rphy(hw, MII_ESTATUS, &phy->estatus); 5060 if (ret_val) 5061 e_warn("Error reading PHY register\n"); 5062 } else { 5063 /* Do not read PHY registers if link is not up 5064 * Set values to typical power-on defaults 5065 */ 5066 phy->bmcr = (BMCR_SPEED1000 | BMCR_ANENABLE | BMCR_FULLDPLX); 5067 phy->bmsr = (BMSR_100FULL | BMSR_100HALF | BMSR_10FULL | 5068 BMSR_10HALF | BMSR_ESTATEN | BMSR_ANEGCAPABLE | 5069 BMSR_ERCAP); 5070 phy->advertise = (ADVERTISE_PAUSE_ASYM | ADVERTISE_PAUSE_CAP | 5071 ADVERTISE_ALL | ADVERTISE_CSMA); 5072 phy->lpa = 0; 5073 phy->expansion = EXPANSION_ENABLENPAGE; 5074 phy->ctrl1000 = ADVERTISE_1000FULL; 5075 phy->stat1000 = 0; 5076 phy->estatus = (ESTATUS_1000_TFULL | ESTATUS_1000_THALF); 5077 } 5078 } 5079 5080 static void e1000_print_link_info(struct e1000_adapter *adapter) 5081 { 5082 struct e1000_hw *hw = &adapter->hw; 5083 u32 ctrl = er32(CTRL); 5084 5085 /* Link status message must follow this format for user tools */ 5086 netdev_info(adapter->netdev, 5087 "NIC Link is Up %d Mbps %s Duplex, Flow Control: %s\n", 5088 adapter->link_speed, 5089 adapter->link_duplex == FULL_DUPLEX ? "Full" : "Half", 5090 (ctrl & E1000_CTRL_TFCE) && (ctrl & E1000_CTRL_RFCE) ? "Rx/Tx" : 5091 (ctrl & E1000_CTRL_RFCE) ? "Rx" : 5092 (ctrl & E1000_CTRL_TFCE) ? "Tx" : "None"); 5093 } 5094 5095 static bool e1000e_has_link(struct e1000_adapter *adapter) 5096 { 5097 struct e1000_hw *hw = &adapter->hw; 5098 bool link_active = false; 5099 s32 ret_val = 0; 5100 5101 /* get_link_status is set on LSC (link status) interrupt or 5102 * Rx sequence error interrupt. get_link_status will stay 5103 * true until the check_for_link establishes link 5104 * for copper adapters ONLY 5105 */ 5106 switch (hw->phy.media_type) { 5107 case e1000_media_type_copper: 5108 if (hw->mac.get_link_status) { 5109 ret_val = hw->mac.ops.check_for_link(hw); 5110 link_active = !hw->mac.get_link_status; 5111 } else { 5112 link_active = true; 5113 } 5114 break; 5115 case e1000_media_type_fiber: 5116 ret_val = hw->mac.ops.check_for_link(hw); 5117 link_active = !!(er32(STATUS) & E1000_STATUS_LU); 5118 break; 5119 case e1000_media_type_internal_serdes: 5120 ret_val = hw->mac.ops.check_for_link(hw); 5121 link_active = hw->mac.serdes_has_link; 5122 break; 5123 default: 5124 case e1000_media_type_unknown: 5125 break; 5126 } 5127 5128 if ((ret_val == -E1000_ERR_PHY) && (hw->phy.type == e1000_phy_igp_3) && 5129 (er32(CTRL) & E1000_PHY_CTRL_GBE_DISABLE)) { 5130 /* See e1000_kmrn_lock_loss_workaround_ich8lan() */ 5131 e_info("Gigabit has been disabled, downgrading speed\n"); 5132 } 5133 5134 return link_active; 5135 } 5136 5137 static void e1000e_enable_receives(struct e1000_adapter *adapter) 5138 { 5139 /* make sure the receive unit is started */ 5140 if ((adapter->flags & FLAG_RX_NEEDS_RESTART) && 5141 (adapter->flags & FLAG_RESTART_NOW)) { 5142 struct e1000_hw *hw = &adapter->hw; 5143 u32 rctl = er32(RCTL); 5144 5145 ew32(RCTL, rctl | E1000_RCTL_EN); 5146 adapter->flags &= ~FLAG_RESTART_NOW; 5147 } 5148 } 5149 5150 static void e1000e_check_82574_phy_workaround(struct e1000_adapter *adapter) 5151 { 5152 struct e1000_hw *hw = &adapter->hw; 5153 5154 /* With 82574 controllers, PHY needs to be checked periodically 5155 * for hung state and reset, if two calls return true 5156 */ 5157 if (e1000_check_phy_82574(hw)) 5158 adapter->phy_hang_count++; 5159 else 5160 adapter->phy_hang_count = 0; 5161 5162 if (adapter->phy_hang_count > 1) { 5163 adapter->phy_hang_count = 0; 5164 e_dbg("PHY appears hung - resetting\n"); 5165 schedule_work(&adapter->reset_task); 5166 } 5167 } 5168 5169 /** 5170 * e1000_watchdog - Timer Call-back 5171 * @t: pointer to timer_list containing private info adapter 5172 **/ 5173 static void e1000_watchdog(struct timer_list *t) 5174 { 5175 struct e1000_adapter *adapter = from_timer(adapter, t, watchdog_timer); 5176 5177 /* Do the rest outside of interrupt context */ 5178 schedule_work(&adapter->watchdog_task); 5179 5180 /* TODO: make this use queue_delayed_work() */ 5181 } 5182 5183 static void e1000_watchdog_task(struct work_struct *work) 5184 { 5185 struct e1000_adapter *adapter = container_of(work, 5186 struct e1000_adapter, 5187 watchdog_task); 5188 struct net_device *netdev = adapter->netdev; 5189 struct e1000_mac_info *mac = &adapter->hw.mac; 5190 struct e1000_phy_info *phy = &adapter->hw.phy; 5191 struct e1000_ring *tx_ring = adapter->tx_ring; 5192 u32 dmoff_exit_timeout = 100, tries = 0; 5193 struct e1000_hw *hw = &adapter->hw; 5194 u32 link, tctl, pcim_state; 5195 5196 if (test_bit(__E1000_DOWN, &adapter->state)) 5197 return; 5198 5199 link = e1000e_has_link(adapter); 5200 if ((netif_carrier_ok(netdev)) && link) { 5201 /* Cancel scheduled suspend requests. */ 5202 pm_runtime_resume(netdev->dev.parent); 5203 5204 e1000e_enable_receives(adapter); 5205 goto link_up; 5206 } 5207 5208 if ((e1000e_enable_tx_pkt_filtering(hw)) && 5209 (adapter->mng_vlan_id != adapter->hw.mng_cookie.vlan_id)) 5210 e1000_update_mng_vlan(adapter); 5211 5212 if (link) { 5213 if (!netif_carrier_ok(netdev)) { 5214 bool txb2b = true; 5215 5216 /* Cancel scheduled suspend requests. */ 5217 pm_runtime_resume(netdev->dev.parent); 5218 5219 /* Checking if MAC is in DMoff state*/ 5220 if (er32(FWSM) & E1000_ICH_FWSM_FW_VALID) { 5221 pcim_state = er32(STATUS); 5222 while (pcim_state & E1000_STATUS_PCIM_STATE) { 5223 if (tries++ == dmoff_exit_timeout) { 5224 e_dbg("Error in exiting dmoff\n"); 5225 break; 5226 } 5227 usleep_range(10000, 20000); 5228 pcim_state = er32(STATUS); 5229 5230 /* Checking if MAC exited DMoff state */ 5231 if (!(pcim_state & E1000_STATUS_PCIM_STATE)) 5232 e1000_phy_hw_reset(&adapter->hw); 5233 } 5234 } 5235 5236 /* update snapshot of PHY registers on LSC */ 5237 e1000_phy_read_status(adapter); 5238 mac->ops.get_link_up_info(&adapter->hw, 5239 &adapter->link_speed, 5240 &adapter->link_duplex); 5241 e1000_print_link_info(adapter); 5242 5243 /* check if SmartSpeed worked */ 5244 e1000e_check_downshift(hw); 5245 if (phy->speed_downgraded) 5246 netdev_warn(netdev, 5247 "Link Speed was downgraded by SmartSpeed\n"); 5248 5249 /* On supported PHYs, check for duplex mismatch only 5250 * if link has autonegotiated at 10/100 half 5251 */ 5252 if ((hw->phy.type == e1000_phy_igp_3 || 5253 hw->phy.type == e1000_phy_bm) && 5254 hw->mac.autoneg && 5255 (adapter->link_speed == SPEED_10 || 5256 adapter->link_speed == SPEED_100) && 5257 (adapter->link_duplex == HALF_DUPLEX)) { 5258 u16 autoneg_exp; 5259 5260 e1e_rphy(hw, MII_EXPANSION, &autoneg_exp); 5261 5262 if (!(autoneg_exp & EXPANSION_NWAY)) 5263 e_info("Autonegotiated half duplex but link partner cannot autoneg. Try forcing full duplex if link gets many collisions.\n"); 5264 } 5265 5266 /* adjust timeout factor according to speed/duplex */ 5267 adapter->tx_timeout_factor = 1; 5268 switch (adapter->link_speed) { 5269 case SPEED_10: 5270 txb2b = false; 5271 adapter->tx_timeout_factor = 16; 5272 break; 5273 case SPEED_100: 5274 txb2b = false; 5275 adapter->tx_timeout_factor = 10; 5276 break; 5277 } 5278 5279 /* workaround: re-program speed mode bit after 5280 * link-up event 5281 */ 5282 if ((adapter->flags & FLAG_TARC_SPEED_MODE_BIT) && 5283 !txb2b) { 5284 u32 tarc0; 5285 5286 tarc0 = er32(TARC(0)); 5287 tarc0 &= ~SPEED_MODE_BIT; 5288 ew32(TARC(0), tarc0); 5289 } 5290 5291 /* disable TSO for pcie and 10/100 speeds, to avoid 5292 * some hardware issues 5293 */ 5294 if (!(adapter->flags & FLAG_TSO_FORCE)) { 5295 switch (adapter->link_speed) { 5296 case SPEED_10: 5297 case SPEED_100: 5298 e_info("10/100 speed: disabling TSO\n"); 5299 netdev->features &= ~NETIF_F_TSO; 5300 netdev->features &= ~NETIF_F_TSO6; 5301 break; 5302 case SPEED_1000: 5303 netdev->features |= NETIF_F_TSO; 5304 netdev->features |= NETIF_F_TSO6; 5305 break; 5306 default: 5307 /* oops */ 5308 break; 5309 } 5310 if (hw->mac.type == e1000_pch_spt) { 5311 netdev->features &= ~NETIF_F_TSO; 5312 netdev->features &= ~NETIF_F_TSO6; 5313 } 5314 } 5315 5316 /* enable transmits in the hardware, need to do this 5317 * after setting TARC(0) 5318 */ 5319 tctl = er32(TCTL); 5320 tctl |= E1000_TCTL_EN; 5321 ew32(TCTL, tctl); 5322 5323 /* Perform any post-link-up configuration before 5324 * reporting link up. 5325 */ 5326 if (phy->ops.cfg_on_link_up) 5327 phy->ops.cfg_on_link_up(hw); 5328 5329 netif_wake_queue(netdev); 5330 netif_carrier_on(netdev); 5331 5332 if (!test_bit(__E1000_DOWN, &adapter->state)) 5333 mod_timer(&adapter->phy_info_timer, 5334 round_jiffies(jiffies + 2 * HZ)); 5335 } 5336 } else { 5337 if (netif_carrier_ok(netdev)) { 5338 adapter->link_speed = 0; 5339 adapter->link_duplex = 0; 5340 /* Link status message must follow this format */ 5341 netdev_info(netdev, "NIC Link is Down\n"); 5342 netif_carrier_off(netdev); 5343 netif_stop_queue(netdev); 5344 if (!test_bit(__E1000_DOWN, &adapter->state)) 5345 mod_timer(&adapter->phy_info_timer, 5346 round_jiffies(jiffies + 2 * HZ)); 5347 5348 /* 8000ES2LAN requires a Rx packet buffer work-around 5349 * on link down event; reset the controller to flush 5350 * the Rx packet buffer. 5351 */ 5352 if (adapter->flags & FLAG_RX_NEEDS_RESTART) 5353 adapter->flags |= FLAG_RESTART_NOW; 5354 else 5355 pm_schedule_suspend(netdev->dev.parent, 5356 LINK_TIMEOUT); 5357 } 5358 } 5359 5360 link_up: 5361 spin_lock(&adapter->stats64_lock); 5362 e1000e_update_stats(adapter); 5363 5364 mac->tx_packet_delta = adapter->stats.tpt - adapter->tpt_old; 5365 adapter->tpt_old = adapter->stats.tpt; 5366 mac->collision_delta = adapter->stats.colc - adapter->colc_old; 5367 adapter->colc_old = adapter->stats.colc; 5368 5369 adapter->gorc = adapter->stats.gorc - adapter->gorc_old; 5370 adapter->gorc_old = adapter->stats.gorc; 5371 adapter->gotc = adapter->stats.gotc - adapter->gotc_old; 5372 adapter->gotc_old = adapter->stats.gotc; 5373 spin_unlock(&adapter->stats64_lock); 5374 5375 /* If the link is lost the controller stops DMA, but 5376 * if there is queued Tx work it cannot be done. So 5377 * reset the controller to flush the Tx packet buffers. 5378 */ 5379 if (!netif_carrier_ok(netdev) && 5380 (e1000_desc_unused(tx_ring) + 1 < tx_ring->count)) 5381 adapter->flags |= FLAG_RESTART_NOW; 5382 5383 /* If reset is necessary, do it outside of interrupt context. */ 5384 if (adapter->flags & FLAG_RESTART_NOW) { 5385 schedule_work(&adapter->reset_task); 5386 /* return immediately since reset is imminent */ 5387 return; 5388 } 5389 5390 e1000e_update_adaptive(&adapter->hw); 5391 5392 /* Simple mode for Interrupt Throttle Rate (ITR) */ 5393 if (adapter->itr_setting == 4) { 5394 /* Symmetric Tx/Rx gets a reduced ITR=2000; 5395 * Total asymmetrical Tx or Rx gets ITR=8000; 5396 * everyone else is between 2000-8000. 5397 */ 5398 u32 goc = (adapter->gotc + adapter->gorc) / 10000; 5399 u32 dif = (adapter->gotc > adapter->gorc ? 5400 adapter->gotc - adapter->gorc : 5401 adapter->gorc - adapter->gotc) / 10000; 5402 u32 itr = goc > 0 ? (dif * 6000 / goc + 2000) : 8000; 5403 5404 e1000e_write_itr(adapter, itr); 5405 } 5406 5407 /* Cause software interrupt to ensure Rx ring is cleaned */ 5408 if (adapter->msix_entries) 5409 ew32(ICS, adapter->rx_ring->ims_val); 5410 else 5411 ew32(ICS, E1000_ICS_RXDMT0); 5412 5413 /* flush pending descriptors to memory before detecting Tx hang */ 5414 e1000e_flush_descriptors(adapter); 5415 5416 /* Force detection of hung controller every watchdog period */ 5417 adapter->detect_tx_hung = true; 5418 5419 /* With 82571 controllers, LAA may be overwritten due to controller 5420 * reset from the other port. Set the appropriate LAA in RAR[0] 5421 */ 5422 if (e1000e_get_laa_state_82571(hw)) 5423 hw->mac.ops.rar_set(hw, adapter->hw.mac.addr, 0); 5424 5425 if (adapter->flags2 & FLAG2_CHECK_PHY_HANG) 5426 e1000e_check_82574_phy_workaround(adapter); 5427 5428 /* Clear valid timestamp stuck in RXSTMPL/H due to a Rx error */ 5429 if (adapter->hwtstamp_config.rx_filter != HWTSTAMP_FILTER_NONE) { 5430 if ((adapter->flags2 & FLAG2_CHECK_RX_HWTSTAMP) && 5431 (er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_VALID)) { 5432 er32(RXSTMPH); 5433 adapter->rx_hwtstamp_cleared++; 5434 } else { 5435 adapter->flags2 |= FLAG2_CHECK_RX_HWTSTAMP; 5436 } 5437 } 5438 5439 /* Reset the timer */ 5440 if (!test_bit(__E1000_DOWN, &adapter->state)) 5441 mod_timer(&adapter->watchdog_timer, 5442 round_jiffies(jiffies + 2 * HZ)); 5443 } 5444 5445 #define E1000_TX_FLAGS_CSUM 0x00000001 5446 #define E1000_TX_FLAGS_VLAN 0x00000002 5447 #define E1000_TX_FLAGS_TSO 0x00000004 5448 #define E1000_TX_FLAGS_IPV4 0x00000008 5449 #define E1000_TX_FLAGS_NO_FCS 0x00000010 5450 #define E1000_TX_FLAGS_HWTSTAMP 0x00000020 5451 #define E1000_TX_FLAGS_VLAN_MASK 0xffff0000 5452 #define E1000_TX_FLAGS_VLAN_SHIFT 16 5453 5454 static int e1000_tso(struct e1000_ring *tx_ring, struct sk_buff *skb, 5455 __be16 protocol) 5456 { 5457 struct e1000_context_desc *context_desc; 5458 struct e1000_buffer *buffer_info; 5459 unsigned int i; 5460 u32 cmd_length = 0; 5461 u16 ipcse = 0, mss; 5462 u8 ipcss, ipcso, tucss, tucso, hdr_len; 5463 int err; 5464 5465 if (!skb_is_gso(skb)) 5466 return 0; 5467 5468 err = skb_cow_head(skb, 0); 5469 if (err < 0) 5470 return err; 5471 5472 hdr_len = skb_tcp_all_headers(skb); 5473 mss = skb_shinfo(skb)->gso_size; 5474 if (protocol == htons(ETH_P_IP)) { 5475 struct iphdr *iph = ip_hdr(skb); 5476 iph->tot_len = 0; 5477 iph->check = 0; 5478 tcp_hdr(skb)->check = ~csum_tcpudp_magic(iph->saddr, iph->daddr, 5479 0, IPPROTO_TCP, 0); 5480 cmd_length = E1000_TXD_CMD_IP; 5481 ipcse = skb_transport_offset(skb) - 1; 5482 } else if (skb_is_gso_v6(skb)) { 5483 tcp_v6_gso_csum_prep(skb); 5484 ipcse = 0; 5485 } 5486 ipcss = skb_network_offset(skb); 5487 ipcso = (void *)&(ip_hdr(skb)->check) - (void *)skb->data; 5488 tucss = skb_transport_offset(skb); 5489 tucso = (void *)&(tcp_hdr(skb)->check) - (void *)skb->data; 5490 5491 cmd_length |= (E1000_TXD_CMD_DEXT | E1000_TXD_CMD_TSE | 5492 E1000_TXD_CMD_TCP | (skb->len - (hdr_len))); 5493 5494 i = tx_ring->next_to_use; 5495 context_desc = E1000_CONTEXT_DESC(*tx_ring, i); 5496 buffer_info = &tx_ring->buffer_info[i]; 5497 5498 context_desc->lower_setup.ip_fields.ipcss = ipcss; 5499 context_desc->lower_setup.ip_fields.ipcso = ipcso; 5500 context_desc->lower_setup.ip_fields.ipcse = cpu_to_le16(ipcse); 5501 context_desc->upper_setup.tcp_fields.tucss = tucss; 5502 context_desc->upper_setup.tcp_fields.tucso = tucso; 5503 context_desc->upper_setup.tcp_fields.tucse = 0; 5504 context_desc->tcp_seg_setup.fields.mss = cpu_to_le16(mss); 5505 context_desc->tcp_seg_setup.fields.hdr_len = hdr_len; 5506 context_desc->cmd_and_length = cpu_to_le32(cmd_length); 5507 5508 buffer_info->time_stamp = jiffies; 5509 buffer_info->next_to_watch = i; 5510 5511 i++; 5512 if (i == tx_ring->count) 5513 i = 0; 5514 tx_ring->next_to_use = i; 5515 5516 return 1; 5517 } 5518 5519 static bool e1000_tx_csum(struct e1000_ring *tx_ring, struct sk_buff *skb, 5520 __be16 protocol) 5521 { 5522 struct e1000_adapter *adapter = tx_ring->adapter; 5523 struct e1000_context_desc *context_desc; 5524 struct e1000_buffer *buffer_info; 5525 unsigned int i; 5526 u8 css; 5527 u32 cmd_len = E1000_TXD_CMD_DEXT; 5528 5529 if (skb->ip_summed != CHECKSUM_PARTIAL) 5530 return false; 5531 5532 switch (protocol) { 5533 case cpu_to_be16(ETH_P_IP): 5534 if (ip_hdr(skb)->protocol == IPPROTO_TCP) 5535 cmd_len |= E1000_TXD_CMD_TCP; 5536 break; 5537 case cpu_to_be16(ETH_P_IPV6): 5538 /* XXX not handling all IPV6 headers */ 5539 if (ipv6_hdr(skb)->nexthdr == IPPROTO_TCP) 5540 cmd_len |= E1000_TXD_CMD_TCP; 5541 break; 5542 default: 5543 if (unlikely(net_ratelimit())) 5544 e_warn("checksum_partial proto=%x!\n", 5545 be16_to_cpu(protocol)); 5546 break; 5547 } 5548 5549 css = skb_checksum_start_offset(skb); 5550 5551 i = tx_ring->next_to_use; 5552 buffer_info = &tx_ring->buffer_info[i]; 5553 context_desc = E1000_CONTEXT_DESC(*tx_ring, i); 5554 5555 context_desc->lower_setup.ip_config = 0; 5556 context_desc->upper_setup.tcp_fields.tucss = css; 5557 context_desc->upper_setup.tcp_fields.tucso = css + skb->csum_offset; 5558 context_desc->upper_setup.tcp_fields.tucse = 0; 5559 context_desc->tcp_seg_setup.data = 0; 5560 context_desc->cmd_and_length = cpu_to_le32(cmd_len); 5561 5562 buffer_info->time_stamp = jiffies; 5563 buffer_info->next_to_watch = i; 5564 5565 i++; 5566 if (i == tx_ring->count) 5567 i = 0; 5568 tx_ring->next_to_use = i; 5569 5570 return true; 5571 } 5572 5573 static int e1000_tx_map(struct e1000_ring *tx_ring, struct sk_buff *skb, 5574 unsigned int first, unsigned int max_per_txd, 5575 unsigned int nr_frags) 5576 { 5577 struct e1000_adapter *adapter = tx_ring->adapter; 5578 struct pci_dev *pdev = adapter->pdev; 5579 struct e1000_buffer *buffer_info; 5580 unsigned int len = skb_headlen(skb); 5581 unsigned int offset = 0, size, count = 0, i; 5582 unsigned int f, bytecount, segs; 5583 5584 i = tx_ring->next_to_use; 5585 5586 while (len) { 5587 buffer_info = &tx_ring->buffer_info[i]; 5588 size = min(len, max_per_txd); 5589 5590 buffer_info->length = size; 5591 buffer_info->time_stamp = jiffies; 5592 buffer_info->next_to_watch = i; 5593 buffer_info->dma = dma_map_single(&pdev->dev, 5594 skb->data + offset, 5595 size, DMA_TO_DEVICE); 5596 buffer_info->mapped_as_page = false; 5597 if (dma_mapping_error(&pdev->dev, buffer_info->dma)) 5598 goto dma_error; 5599 5600 len -= size; 5601 offset += size; 5602 count++; 5603 5604 if (len) { 5605 i++; 5606 if (i == tx_ring->count) 5607 i = 0; 5608 } 5609 } 5610 5611 for (f = 0; f < nr_frags; f++) { 5612 const skb_frag_t *frag = &skb_shinfo(skb)->frags[f]; 5613 5614 len = skb_frag_size(frag); 5615 offset = 0; 5616 5617 while (len) { 5618 i++; 5619 if (i == tx_ring->count) 5620 i = 0; 5621 5622 buffer_info = &tx_ring->buffer_info[i]; 5623 size = min(len, max_per_txd); 5624 5625 buffer_info->length = size; 5626 buffer_info->time_stamp = jiffies; 5627 buffer_info->next_to_watch = i; 5628 buffer_info->dma = skb_frag_dma_map(&pdev->dev, frag, 5629 offset, size, 5630 DMA_TO_DEVICE); 5631 buffer_info->mapped_as_page = true; 5632 if (dma_mapping_error(&pdev->dev, buffer_info->dma)) 5633 goto dma_error; 5634 5635 len -= size; 5636 offset += size; 5637 count++; 5638 } 5639 } 5640 5641 segs = skb_shinfo(skb)->gso_segs ? : 1; 5642 /* multiply data chunks by size of headers */ 5643 bytecount = ((segs - 1) * skb_headlen(skb)) + skb->len; 5644 5645 tx_ring->buffer_info[i].skb = skb; 5646 tx_ring->buffer_info[i].segs = segs; 5647 tx_ring->buffer_info[i].bytecount = bytecount; 5648 tx_ring->buffer_info[first].next_to_watch = i; 5649 5650 return count; 5651 5652 dma_error: 5653 dev_err(&pdev->dev, "Tx DMA map failed\n"); 5654 buffer_info->dma = 0; 5655 if (count) 5656 count--; 5657 5658 while (count--) { 5659 if (i == 0) 5660 i += tx_ring->count; 5661 i--; 5662 buffer_info = &tx_ring->buffer_info[i]; 5663 e1000_put_txbuf(tx_ring, buffer_info, true); 5664 } 5665 5666 return 0; 5667 } 5668 5669 static void e1000_tx_queue(struct e1000_ring *tx_ring, int tx_flags, int count) 5670 { 5671 struct e1000_adapter *adapter = tx_ring->adapter; 5672 struct e1000_tx_desc *tx_desc = NULL; 5673 struct e1000_buffer *buffer_info; 5674 u32 txd_upper = 0, txd_lower = E1000_TXD_CMD_IFCS; 5675 unsigned int i; 5676 5677 if (tx_flags & E1000_TX_FLAGS_TSO) { 5678 txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D | 5679 E1000_TXD_CMD_TSE; 5680 txd_upper |= E1000_TXD_POPTS_TXSM << 8; 5681 5682 if (tx_flags & E1000_TX_FLAGS_IPV4) 5683 txd_upper |= E1000_TXD_POPTS_IXSM << 8; 5684 } 5685 5686 if (tx_flags & E1000_TX_FLAGS_CSUM) { 5687 txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D; 5688 txd_upper |= E1000_TXD_POPTS_TXSM << 8; 5689 } 5690 5691 if (tx_flags & E1000_TX_FLAGS_VLAN) { 5692 txd_lower |= E1000_TXD_CMD_VLE; 5693 txd_upper |= (tx_flags & E1000_TX_FLAGS_VLAN_MASK); 5694 } 5695 5696 if (unlikely(tx_flags & E1000_TX_FLAGS_NO_FCS)) 5697 txd_lower &= ~(E1000_TXD_CMD_IFCS); 5698 5699 if (unlikely(tx_flags & E1000_TX_FLAGS_HWTSTAMP)) { 5700 txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D; 5701 txd_upper |= E1000_TXD_EXTCMD_TSTAMP; 5702 } 5703 5704 i = tx_ring->next_to_use; 5705 5706 do { 5707 buffer_info = &tx_ring->buffer_info[i]; 5708 tx_desc = E1000_TX_DESC(*tx_ring, i); 5709 tx_desc->buffer_addr = cpu_to_le64(buffer_info->dma); 5710 tx_desc->lower.data = cpu_to_le32(txd_lower | 5711 buffer_info->length); 5712 tx_desc->upper.data = cpu_to_le32(txd_upper); 5713 5714 i++; 5715 if (i == tx_ring->count) 5716 i = 0; 5717 } while (--count > 0); 5718 5719 tx_desc->lower.data |= cpu_to_le32(adapter->txd_cmd); 5720 5721 /* txd_cmd re-enables FCS, so we'll re-disable it here as desired. */ 5722 if (unlikely(tx_flags & E1000_TX_FLAGS_NO_FCS)) 5723 tx_desc->lower.data &= ~(cpu_to_le32(E1000_TXD_CMD_IFCS)); 5724 5725 /* Force memory writes to complete before letting h/w 5726 * know there are new descriptors to fetch. (Only 5727 * applicable for weak-ordered memory model archs, 5728 * such as IA-64). 5729 */ 5730 wmb(); 5731 5732 tx_ring->next_to_use = i; 5733 } 5734 5735 #define MINIMUM_DHCP_PACKET_SIZE 282 5736 static int e1000_transfer_dhcp_info(struct e1000_adapter *adapter, 5737 struct sk_buff *skb) 5738 { 5739 struct e1000_hw *hw = &adapter->hw; 5740 u16 length, offset; 5741 5742 if (skb_vlan_tag_present(skb) && 5743 !((skb_vlan_tag_get(skb) == adapter->hw.mng_cookie.vlan_id) && 5744 (adapter->hw.mng_cookie.status & 5745 E1000_MNG_DHCP_COOKIE_STATUS_VLAN))) 5746 return 0; 5747 5748 if (skb->len <= MINIMUM_DHCP_PACKET_SIZE) 5749 return 0; 5750 5751 if (((struct ethhdr *)skb->data)->h_proto != htons(ETH_P_IP)) 5752 return 0; 5753 5754 { 5755 const struct iphdr *ip = (struct iphdr *)((u8 *)skb->data + 14); 5756 struct udphdr *udp; 5757 5758 if (ip->protocol != IPPROTO_UDP) 5759 return 0; 5760 5761 udp = (struct udphdr *)((u8 *)ip + (ip->ihl << 2)); 5762 if (ntohs(udp->dest) != 67) 5763 return 0; 5764 5765 offset = (u8 *)udp + 8 - skb->data; 5766 length = skb->len - offset; 5767 return e1000e_mng_write_dhcp_info(hw, (u8 *)udp + 8, length); 5768 } 5769 5770 return 0; 5771 } 5772 5773 static int __e1000_maybe_stop_tx(struct e1000_ring *tx_ring, int size) 5774 { 5775 struct e1000_adapter *adapter = tx_ring->adapter; 5776 5777 netif_stop_queue(adapter->netdev); 5778 /* Herbert's original patch had: 5779 * smp_mb__after_netif_stop_queue(); 5780 * but since that doesn't exist yet, just open code it. 5781 */ 5782 smp_mb(); 5783 5784 /* We need to check again in a case another CPU has just 5785 * made room available. 5786 */ 5787 if (e1000_desc_unused(tx_ring) < size) 5788 return -EBUSY; 5789 5790 /* A reprieve! */ 5791 netif_start_queue(adapter->netdev); 5792 ++adapter->restart_queue; 5793 return 0; 5794 } 5795 5796 static int e1000_maybe_stop_tx(struct e1000_ring *tx_ring, int size) 5797 { 5798 BUG_ON(size > tx_ring->count); 5799 5800 if (e1000_desc_unused(tx_ring) >= size) 5801 return 0; 5802 return __e1000_maybe_stop_tx(tx_ring, size); 5803 } 5804 5805 static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb, 5806 struct net_device *netdev) 5807 { 5808 struct e1000_adapter *adapter = netdev_priv(netdev); 5809 struct e1000_ring *tx_ring = adapter->tx_ring; 5810 unsigned int first; 5811 unsigned int tx_flags = 0; 5812 unsigned int len = skb_headlen(skb); 5813 unsigned int nr_frags; 5814 unsigned int mss; 5815 int count = 0; 5816 int tso; 5817 unsigned int f; 5818 __be16 protocol = vlan_get_protocol(skb); 5819 5820 if (test_bit(__E1000_DOWN, &adapter->state)) { 5821 dev_kfree_skb_any(skb); 5822 return NETDEV_TX_OK; 5823 } 5824 5825 if (skb->len <= 0) { 5826 dev_kfree_skb_any(skb); 5827 return NETDEV_TX_OK; 5828 } 5829 5830 /* The minimum packet size with TCTL.PSP set is 17 bytes so 5831 * pad skb in order to meet this minimum size requirement 5832 */ 5833 if (skb_put_padto(skb, 17)) 5834 return NETDEV_TX_OK; 5835 5836 mss = skb_shinfo(skb)->gso_size; 5837 if (mss) { 5838 u8 hdr_len; 5839 5840 /* TSO Workaround for 82571/2/3 Controllers -- if skb->data 5841 * points to just header, pull a few bytes of payload from 5842 * frags into skb->data 5843 */ 5844 hdr_len = skb_tcp_all_headers(skb); 5845 /* we do this workaround for ES2LAN, but it is un-necessary, 5846 * avoiding it could save a lot of cycles 5847 */ 5848 if (skb->data_len && (hdr_len == len)) { 5849 unsigned int pull_size; 5850 5851 pull_size = min_t(unsigned int, 4, skb->data_len); 5852 if (!__pskb_pull_tail(skb, pull_size)) { 5853 e_err("__pskb_pull_tail failed.\n"); 5854 dev_kfree_skb_any(skb); 5855 return NETDEV_TX_OK; 5856 } 5857 len = skb_headlen(skb); 5858 } 5859 } 5860 5861 /* reserve a descriptor for the offload context */ 5862 if ((mss) || (skb->ip_summed == CHECKSUM_PARTIAL)) 5863 count++; 5864 count++; 5865 5866 count += DIV_ROUND_UP(len, adapter->tx_fifo_limit); 5867 5868 nr_frags = skb_shinfo(skb)->nr_frags; 5869 for (f = 0; f < nr_frags; f++) 5870 count += DIV_ROUND_UP(skb_frag_size(&skb_shinfo(skb)->frags[f]), 5871 adapter->tx_fifo_limit); 5872 5873 if (adapter->hw.mac.tx_pkt_filtering) 5874 e1000_transfer_dhcp_info(adapter, skb); 5875 5876 /* need: count + 2 desc gap to keep tail from touching 5877 * head, otherwise try next time 5878 */ 5879 if (e1000_maybe_stop_tx(tx_ring, count + 2)) 5880 return NETDEV_TX_BUSY; 5881 5882 if (skb_vlan_tag_present(skb)) { 5883 tx_flags |= E1000_TX_FLAGS_VLAN; 5884 tx_flags |= (skb_vlan_tag_get(skb) << 5885 E1000_TX_FLAGS_VLAN_SHIFT); 5886 } 5887 5888 first = tx_ring->next_to_use; 5889 5890 tso = e1000_tso(tx_ring, skb, protocol); 5891 if (tso < 0) { 5892 dev_kfree_skb_any(skb); 5893 return NETDEV_TX_OK; 5894 } 5895 5896 if (tso) 5897 tx_flags |= E1000_TX_FLAGS_TSO; 5898 else if (e1000_tx_csum(tx_ring, skb, protocol)) 5899 tx_flags |= E1000_TX_FLAGS_CSUM; 5900 5901 /* Old method was to assume IPv4 packet by default if TSO was enabled. 5902 * 82571 hardware supports TSO capabilities for IPv6 as well... 5903 * no longer assume, we must. 5904 */ 5905 if (protocol == htons(ETH_P_IP)) 5906 tx_flags |= E1000_TX_FLAGS_IPV4; 5907 5908 if (unlikely(skb->no_fcs)) 5909 tx_flags |= E1000_TX_FLAGS_NO_FCS; 5910 5911 /* if count is 0 then mapping error has occurred */ 5912 count = e1000_tx_map(tx_ring, skb, first, adapter->tx_fifo_limit, 5913 nr_frags); 5914 if (count) { 5915 if (unlikely(skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP) && 5916 (adapter->flags & FLAG_HAS_HW_TIMESTAMP)) { 5917 if (!adapter->tx_hwtstamp_skb) { 5918 skb_shinfo(skb)->tx_flags |= SKBTX_IN_PROGRESS; 5919 tx_flags |= E1000_TX_FLAGS_HWTSTAMP; 5920 adapter->tx_hwtstamp_skb = skb_get(skb); 5921 adapter->tx_hwtstamp_start = jiffies; 5922 schedule_work(&adapter->tx_hwtstamp_work); 5923 } else { 5924 adapter->tx_hwtstamp_skipped++; 5925 } 5926 } 5927 5928 skb_tx_timestamp(skb); 5929 5930 netdev_sent_queue(netdev, skb->len); 5931 e1000_tx_queue(tx_ring, tx_flags, count); 5932 /* Make sure there is space in the ring for the next send. */ 5933 e1000_maybe_stop_tx(tx_ring, 5934 ((MAX_SKB_FRAGS + 1) * 5935 DIV_ROUND_UP(PAGE_SIZE, 5936 adapter->tx_fifo_limit) + 4)); 5937 5938 if (!netdev_xmit_more() || 5939 netif_xmit_stopped(netdev_get_tx_queue(netdev, 0))) { 5940 if (adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA) 5941 e1000e_update_tdt_wa(tx_ring, 5942 tx_ring->next_to_use); 5943 else 5944 writel(tx_ring->next_to_use, tx_ring->tail); 5945 } 5946 } else { 5947 dev_kfree_skb_any(skb); 5948 tx_ring->buffer_info[first].time_stamp = 0; 5949 tx_ring->next_to_use = first; 5950 } 5951 5952 return NETDEV_TX_OK; 5953 } 5954 5955 /** 5956 * e1000_tx_timeout - Respond to a Tx Hang 5957 * @netdev: network interface device structure 5958 * @txqueue: index of the hung queue (unused) 5959 **/ 5960 static void e1000_tx_timeout(struct net_device *netdev, unsigned int __always_unused txqueue) 5961 { 5962 struct e1000_adapter *adapter = netdev_priv(netdev); 5963 5964 /* Do the reset outside of interrupt context */ 5965 adapter->tx_timeout_count++; 5966 schedule_work(&adapter->reset_task); 5967 } 5968 5969 static void e1000_reset_task(struct work_struct *work) 5970 { 5971 struct e1000_adapter *adapter; 5972 adapter = container_of(work, struct e1000_adapter, reset_task); 5973 5974 rtnl_lock(); 5975 /* don't run the task if already down */ 5976 if (test_bit(__E1000_DOWN, &adapter->state)) { 5977 rtnl_unlock(); 5978 return; 5979 } 5980 5981 if (!(adapter->flags & FLAG_RESTART_NOW)) { 5982 e1000e_dump(adapter); 5983 e_err("Reset adapter unexpectedly\n"); 5984 } 5985 e1000e_reinit_locked(adapter); 5986 rtnl_unlock(); 5987 } 5988 5989 /** 5990 * e1000e_get_stats64 - Get System Network Statistics 5991 * @netdev: network interface device structure 5992 * @stats: rtnl_link_stats64 pointer 5993 * 5994 * Returns the address of the device statistics structure. 5995 **/ 5996 void e1000e_get_stats64(struct net_device *netdev, 5997 struct rtnl_link_stats64 *stats) 5998 { 5999 struct e1000_adapter *adapter = netdev_priv(netdev); 6000 6001 spin_lock(&adapter->stats64_lock); 6002 e1000e_update_stats(adapter); 6003 /* Fill out the OS statistics structure */ 6004 stats->rx_bytes = adapter->stats.gorc; 6005 stats->rx_packets = adapter->stats.gprc; 6006 stats->tx_bytes = adapter->stats.gotc; 6007 stats->tx_packets = adapter->stats.gptc; 6008 stats->multicast = adapter->stats.mprc; 6009 stats->collisions = adapter->stats.colc; 6010 6011 /* Rx Errors */ 6012 6013 /* RLEC on some newer hardware can be incorrect so build 6014 * our own version based on RUC and ROC 6015 */ 6016 stats->rx_errors = adapter->stats.rxerrc + 6017 adapter->stats.crcerrs + adapter->stats.algnerrc + 6018 adapter->stats.ruc + adapter->stats.roc + adapter->stats.cexterr; 6019 stats->rx_length_errors = adapter->stats.ruc + adapter->stats.roc; 6020 stats->rx_crc_errors = adapter->stats.crcerrs; 6021 stats->rx_frame_errors = adapter->stats.algnerrc; 6022 stats->rx_missed_errors = adapter->stats.mpc; 6023 6024 /* Tx Errors */ 6025 stats->tx_errors = adapter->stats.ecol + adapter->stats.latecol; 6026 stats->tx_aborted_errors = adapter->stats.ecol; 6027 stats->tx_window_errors = adapter->stats.latecol; 6028 stats->tx_carrier_errors = adapter->stats.tncrs; 6029 6030 /* Tx Dropped needs to be maintained elsewhere */ 6031 6032 spin_unlock(&adapter->stats64_lock); 6033 } 6034 6035 /** 6036 * e1000_change_mtu - Change the Maximum Transfer Unit 6037 * @netdev: network interface device structure 6038 * @new_mtu: new value for maximum frame size 6039 * 6040 * Returns 0 on success, negative on failure 6041 **/ 6042 static int e1000_change_mtu(struct net_device *netdev, int new_mtu) 6043 { 6044 struct e1000_adapter *adapter = netdev_priv(netdev); 6045 int max_frame = new_mtu + VLAN_ETH_HLEN + ETH_FCS_LEN; 6046 6047 /* Jumbo frame support */ 6048 if ((new_mtu > ETH_DATA_LEN) && 6049 !(adapter->flags & FLAG_HAS_JUMBO_FRAMES)) { 6050 e_err("Jumbo Frames not supported.\n"); 6051 return -EINVAL; 6052 } 6053 6054 /* Jumbo frame workaround on 82579 and newer requires CRC be stripped */ 6055 if ((adapter->hw.mac.type >= e1000_pch2lan) && 6056 !(adapter->flags2 & FLAG2_CRC_STRIPPING) && 6057 (new_mtu > ETH_DATA_LEN)) { 6058 e_err("Jumbo Frames not supported on this device when CRC stripping is disabled.\n"); 6059 return -EINVAL; 6060 } 6061 6062 while (test_and_set_bit(__E1000_RESETTING, &adapter->state)) 6063 usleep_range(1000, 1100); 6064 /* e1000e_down -> e1000e_reset dependent on max_frame_size & mtu */ 6065 adapter->max_frame_size = max_frame; 6066 netdev_dbg(netdev, "changing MTU from %d to %d\n", 6067 netdev->mtu, new_mtu); 6068 netdev->mtu = new_mtu; 6069 6070 pm_runtime_get_sync(netdev->dev.parent); 6071 6072 if (netif_running(netdev)) 6073 e1000e_down(adapter, true); 6074 6075 /* NOTE: netdev_alloc_skb reserves 16 bytes, and typically NET_IP_ALIGN 6076 * means we reserve 2 more, this pushes us to allocate from the next 6077 * larger slab size. 6078 * i.e. RXBUFFER_2048 --> size-4096 slab 6079 * However with the new *_jumbo_rx* routines, jumbo receives will use 6080 * fragmented skbs 6081 */ 6082 6083 if (max_frame <= 2048) 6084 adapter->rx_buffer_len = 2048; 6085 else 6086 adapter->rx_buffer_len = 4096; 6087 6088 /* adjust allocation if LPE protects us, and we aren't using SBP */ 6089 if (max_frame <= (VLAN_ETH_FRAME_LEN + ETH_FCS_LEN)) 6090 adapter->rx_buffer_len = VLAN_ETH_FRAME_LEN + ETH_FCS_LEN; 6091 6092 if (netif_running(netdev)) 6093 e1000e_up(adapter); 6094 else 6095 e1000e_reset(adapter); 6096 6097 pm_runtime_put_sync(netdev->dev.parent); 6098 6099 clear_bit(__E1000_RESETTING, &adapter->state); 6100 6101 return 0; 6102 } 6103 6104 static int e1000_mii_ioctl(struct net_device *netdev, struct ifreq *ifr, 6105 int cmd) 6106 { 6107 struct e1000_adapter *adapter = netdev_priv(netdev); 6108 struct mii_ioctl_data *data = if_mii(ifr); 6109 6110 if (adapter->hw.phy.media_type != e1000_media_type_copper) 6111 return -EOPNOTSUPP; 6112 6113 switch (cmd) { 6114 case SIOCGMIIPHY: 6115 data->phy_id = adapter->hw.phy.addr; 6116 break; 6117 case SIOCGMIIREG: 6118 e1000_phy_read_status(adapter); 6119 6120 switch (data->reg_num & 0x1F) { 6121 case MII_BMCR: 6122 data->val_out = adapter->phy_regs.bmcr; 6123 break; 6124 case MII_BMSR: 6125 data->val_out = adapter->phy_regs.bmsr; 6126 break; 6127 case MII_PHYSID1: 6128 data->val_out = (adapter->hw.phy.id >> 16); 6129 break; 6130 case MII_PHYSID2: 6131 data->val_out = (adapter->hw.phy.id & 0xFFFF); 6132 break; 6133 case MII_ADVERTISE: 6134 data->val_out = adapter->phy_regs.advertise; 6135 break; 6136 case MII_LPA: 6137 data->val_out = adapter->phy_regs.lpa; 6138 break; 6139 case MII_EXPANSION: 6140 data->val_out = adapter->phy_regs.expansion; 6141 break; 6142 case MII_CTRL1000: 6143 data->val_out = adapter->phy_regs.ctrl1000; 6144 break; 6145 case MII_STAT1000: 6146 data->val_out = adapter->phy_regs.stat1000; 6147 break; 6148 case MII_ESTATUS: 6149 data->val_out = adapter->phy_regs.estatus; 6150 break; 6151 default: 6152 return -EIO; 6153 } 6154 break; 6155 case SIOCSMIIREG: 6156 default: 6157 return -EOPNOTSUPP; 6158 } 6159 return 0; 6160 } 6161 6162 /** 6163 * e1000e_hwtstamp_set - control hardware time stamping 6164 * @netdev: network interface device structure 6165 * @ifr: interface request 6166 * 6167 * Outgoing time stamping can be enabled and disabled. Play nice and 6168 * disable it when requested, although it shouldn't cause any overhead 6169 * when no packet needs it. At most one packet in the queue may be 6170 * marked for time stamping, otherwise it would be impossible to tell 6171 * for sure to which packet the hardware time stamp belongs. 6172 * 6173 * Incoming time stamping has to be configured via the hardware filters. 6174 * Not all combinations are supported, in particular event type has to be 6175 * specified. Matching the kind of event packet is not supported, with the 6176 * exception of "all V2 events regardless of level 2 or 4". 6177 **/ 6178 static int e1000e_hwtstamp_set(struct net_device *netdev, struct ifreq *ifr) 6179 { 6180 struct e1000_adapter *adapter = netdev_priv(netdev); 6181 struct hwtstamp_config config; 6182 int ret_val; 6183 6184 if (copy_from_user(&config, ifr->ifr_data, sizeof(config))) 6185 return -EFAULT; 6186 6187 ret_val = e1000e_config_hwtstamp(adapter, &config); 6188 if (ret_val) 6189 return ret_val; 6190 6191 switch (config.rx_filter) { 6192 case HWTSTAMP_FILTER_PTP_V2_L4_SYNC: 6193 case HWTSTAMP_FILTER_PTP_V2_L2_SYNC: 6194 case HWTSTAMP_FILTER_PTP_V2_SYNC: 6195 case HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ: 6196 case HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ: 6197 case HWTSTAMP_FILTER_PTP_V2_DELAY_REQ: 6198 /* With V2 type filters which specify a Sync or Delay Request, 6199 * Path Delay Request/Response messages are also time stamped 6200 * by hardware so notify the caller the requested packets plus 6201 * some others are time stamped. 6202 */ 6203 config.rx_filter = HWTSTAMP_FILTER_SOME; 6204 break; 6205 default: 6206 break; 6207 } 6208 6209 return copy_to_user(ifr->ifr_data, &config, 6210 sizeof(config)) ? -EFAULT : 0; 6211 } 6212 6213 static int e1000e_hwtstamp_get(struct net_device *netdev, struct ifreq *ifr) 6214 { 6215 struct e1000_adapter *adapter = netdev_priv(netdev); 6216 6217 return copy_to_user(ifr->ifr_data, &adapter->hwtstamp_config, 6218 sizeof(adapter->hwtstamp_config)) ? -EFAULT : 0; 6219 } 6220 6221 static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd) 6222 { 6223 switch (cmd) { 6224 case SIOCGMIIPHY: 6225 case SIOCGMIIREG: 6226 case SIOCSMIIREG: 6227 return e1000_mii_ioctl(netdev, ifr, cmd); 6228 case SIOCSHWTSTAMP: 6229 return e1000e_hwtstamp_set(netdev, ifr); 6230 case SIOCGHWTSTAMP: 6231 return e1000e_hwtstamp_get(netdev, ifr); 6232 default: 6233 return -EOPNOTSUPP; 6234 } 6235 } 6236 6237 static int e1000_init_phy_wakeup(struct e1000_adapter *adapter, u32 wufc) 6238 { 6239 struct e1000_hw *hw = &adapter->hw; 6240 u32 i, mac_reg, wuc; 6241 u16 phy_reg, wuc_enable; 6242 int retval; 6243 6244 /* copy MAC RARs to PHY RARs */ 6245 e1000_copy_rx_addrs_to_phy_ich8lan(hw); 6246 6247 retval = hw->phy.ops.acquire(hw); 6248 if (retval) { 6249 e_err("Could not acquire PHY\n"); 6250 return retval; 6251 } 6252 6253 /* Enable access to wakeup registers on and set page to BM_WUC_PAGE */ 6254 retval = e1000_enable_phy_wakeup_reg_access_bm(hw, &wuc_enable); 6255 if (retval) 6256 goto release; 6257 6258 /* copy MAC MTA to PHY MTA - only needed for pchlan */ 6259 for (i = 0; i < adapter->hw.mac.mta_reg_count; i++) { 6260 mac_reg = E1000_READ_REG_ARRAY(hw, E1000_MTA, i); 6261 hw->phy.ops.write_reg_page(hw, BM_MTA(i), 6262 (u16)(mac_reg & 0xFFFF)); 6263 hw->phy.ops.write_reg_page(hw, BM_MTA(i) + 1, 6264 (u16)((mac_reg >> 16) & 0xFFFF)); 6265 } 6266 6267 /* configure PHY Rx Control register */ 6268 hw->phy.ops.read_reg_page(&adapter->hw, BM_RCTL, &phy_reg); 6269 mac_reg = er32(RCTL); 6270 if (mac_reg & E1000_RCTL_UPE) 6271 phy_reg |= BM_RCTL_UPE; 6272 if (mac_reg & E1000_RCTL_MPE) 6273 phy_reg |= BM_RCTL_MPE; 6274 phy_reg &= ~(BM_RCTL_MO_MASK); 6275 if (mac_reg & E1000_RCTL_MO_3) 6276 phy_reg |= (((mac_reg & E1000_RCTL_MO_3) >> E1000_RCTL_MO_SHIFT) 6277 << BM_RCTL_MO_SHIFT); 6278 if (mac_reg & E1000_RCTL_BAM) 6279 phy_reg |= BM_RCTL_BAM; 6280 if (mac_reg & E1000_RCTL_PMCF) 6281 phy_reg |= BM_RCTL_PMCF; 6282 mac_reg = er32(CTRL); 6283 if (mac_reg & E1000_CTRL_RFCE) 6284 phy_reg |= BM_RCTL_RFCE; 6285 hw->phy.ops.write_reg_page(&adapter->hw, BM_RCTL, phy_reg); 6286 6287 wuc = E1000_WUC_PME_EN; 6288 if (wufc & (E1000_WUFC_MAG | E1000_WUFC_LNKC)) 6289 wuc |= E1000_WUC_APME; 6290 6291 /* enable PHY wakeup in MAC register */ 6292 ew32(WUFC, wufc); 6293 ew32(WUC, (E1000_WUC_PHY_WAKE | E1000_WUC_APMPME | 6294 E1000_WUC_PME_STATUS | wuc)); 6295 6296 /* configure and enable PHY wakeup in PHY registers */ 6297 hw->phy.ops.write_reg_page(&adapter->hw, BM_WUFC, wufc); 6298 hw->phy.ops.write_reg_page(&adapter->hw, BM_WUC, wuc); 6299 6300 /* activate PHY wakeup */ 6301 wuc_enable |= BM_WUC_ENABLE_BIT | BM_WUC_HOST_WU_BIT; 6302 retval = e1000_disable_phy_wakeup_reg_access_bm(hw, &wuc_enable); 6303 if (retval) 6304 e_err("Could not set PHY Host Wakeup bit\n"); 6305 release: 6306 hw->phy.ops.release(hw); 6307 6308 return retval; 6309 } 6310 6311 static void e1000e_flush_lpic(struct pci_dev *pdev) 6312 { 6313 struct net_device *netdev = pci_get_drvdata(pdev); 6314 struct e1000_adapter *adapter = netdev_priv(netdev); 6315 struct e1000_hw *hw = &adapter->hw; 6316 u32 ret_val; 6317 6318 pm_runtime_get_sync(netdev->dev.parent); 6319 6320 ret_val = hw->phy.ops.acquire(hw); 6321 if (ret_val) 6322 goto fl_out; 6323 6324 pr_info("EEE TX LPI TIMER: %08X\n", 6325 er32(LPIC) >> E1000_LPIC_LPIET_SHIFT); 6326 6327 hw->phy.ops.release(hw); 6328 6329 fl_out: 6330 pm_runtime_put_sync(netdev->dev.parent); 6331 } 6332 6333 /* S0ix implementation */ 6334 static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter) 6335 { 6336 struct e1000_hw *hw = &adapter->hw; 6337 u32 mac_data; 6338 u16 phy_data; 6339 6340 if (er32(FWSM) & E1000_ICH_FWSM_FW_VALID && 6341 hw->mac.type >= e1000_pch_adp) { 6342 /* Request ME configure the device for S0ix */ 6343 mac_data = er32(H2ME); 6344 mac_data |= E1000_H2ME_START_DPG; 6345 mac_data &= ~E1000_H2ME_EXIT_DPG; 6346 trace_e1000e_trace_mac_register(mac_data); 6347 ew32(H2ME, mac_data); 6348 } else { 6349 /* Request driver configure the device to S0ix */ 6350 /* Disable the periodic inband message, 6351 * don't request PCIe clock in K1 page770_17[10:9] = 10b 6352 */ 6353 e1e_rphy(hw, HV_PM_CTRL, &phy_data); 6354 phy_data &= ~HV_PM_CTRL_K1_CLK_REQ; 6355 phy_data |= BIT(10); 6356 e1e_wphy(hw, HV_PM_CTRL, phy_data); 6357 6358 /* Make sure we don't exit K1 every time a new packet arrives 6359 * 772_29[5] = 1 CS_Mode_Stay_In_K1 6360 */ 6361 e1e_rphy(hw, I217_CGFREG, &phy_data); 6362 phy_data |= BIT(5); 6363 e1e_wphy(hw, I217_CGFREG, phy_data); 6364 6365 /* Change the MAC/PHY interface to SMBus 6366 * Force the SMBus in PHY page769_23[0] = 1 6367 * Force the SMBus in MAC CTRL_EXT[11] = 1 6368 */ 6369 e1e_rphy(hw, CV_SMB_CTRL, &phy_data); 6370 phy_data |= CV_SMB_CTRL_FORCE_SMBUS; 6371 e1e_wphy(hw, CV_SMB_CTRL, phy_data); 6372 mac_data = er32(CTRL_EXT); 6373 mac_data |= E1000_CTRL_EXT_FORCE_SMBUS; 6374 ew32(CTRL_EXT, mac_data); 6375 6376 /* DFT control: PHY bit: page769_20[0] = 1 6377 * page769_20[7] - PHY PLL stop 6378 * page769_20[8] - PHY go to the electrical idle 6379 * page769_20[9] - PHY serdes disable 6380 * Gate PPW via EXTCNF_CTRL - set 0x0F00[7] = 1 6381 */ 6382 e1e_rphy(hw, I82579_DFT_CTRL, &phy_data); 6383 phy_data |= BIT(0); 6384 phy_data |= BIT(7); 6385 phy_data |= BIT(8); 6386 phy_data |= BIT(9); 6387 e1e_wphy(hw, I82579_DFT_CTRL, phy_data); 6388 6389 mac_data = er32(EXTCNF_CTRL); 6390 mac_data |= E1000_EXTCNF_CTRL_GATE_PHY_CFG; 6391 ew32(EXTCNF_CTRL, mac_data); 6392 6393 /* Enable the Dynamic Power Gating in the MAC */ 6394 mac_data = er32(FEXTNVM7); 6395 mac_data |= BIT(22); 6396 ew32(FEXTNVM7, mac_data); 6397 6398 /* Disable disconnected cable conditioning for Power Gating */ 6399 mac_data = er32(DPGFR); 6400 mac_data |= BIT(2); 6401 ew32(DPGFR, mac_data); 6402 6403 /* Don't wake from dynamic Power Gating with clock request */ 6404 mac_data = er32(FEXTNVM12); 6405 mac_data |= BIT(12); 6406 ew32(FEXTNVM12, mac_data); 6407 6408 /* Ungate PGCB clock */ 6409 mac_data = er32(FEXTNVM9); 6410 mac_data &= ~BIT(28); 6411 ew32(FEXTNVM9, mac_data); 6412 6413 /* Enable K1 off to enable mPHY Power Gating */ 6414 mac_data = er32(FEXTNVM6); 6415 mac_data |= BIT(31); 6416 ew32(FEXTNVM6, mac_data); 6417 6418 /* Enable mPHY power gating for any link and speed */ 6419 mac_data = er32(FEXTNVM8); 6420 mac_data |= BIT(9); 6421 ew32(FEXTNVM8, mac_data); 6422 6423 /* Enable the Dynamic Clock Gating in the DMA and MAC */ 6424 mac_data = er32(CTRL_EXT); 6425 mac_data |= E1000_CTRL_EXT_DMA_DYN_CLK_EN; 6426 ew32(CTRL_EXT, mac_data); 6427 6428 /* No MAC DPG gating SLP_S0 in modern standby 6429 * Switch the logic of the lanphypc to use PMC counter 6430 */ 6431 mac_data = er32(FEXTNVM5); 6432 mac_data |= BIT(7); 6433 ew32(FEXTNVM5, mac_data); 6434 } 6435 6436 /* Disable the time synchronization clock */ 6437 mac_data = er32(FEXTNVM7); 6438 mac_data |= BIT(31); 6439 mac_data &= ~BIT(0); 6440 ew32(FEXTNVM7, mac_data); 6441 6442 /* Dynamic Power Gating Enable */ 6443 mac_data = er32(CTRL_EXT); 6444 mac_data |= BIT(3); 6445 ew32(CTRL_EXT, mac_data); 6446 6447 /* Check MAC Tx/Rx packet buffer pointers. 6448 * Reset MAC Tx/Rx packet buffer pointers to suppress any 6449 * pending traffic indication that would prevent power gating. 6450 */ 6451 mac_data = er32(TDFH); 6452 if (mac_data) 6453 ew32(TDFH, 0); 6454 mac_data = er32(TDFT); 6455 if (mac_data) 6456 ew32(TDFT, 0); 6457 mac_data = er32(TDFHS); 6458 if (mac_data) 6459 ew32(TDFHS, 0); 6460 mac_data = er32(TDFTS); 6461 if (mac_data) 6462 ew32(TDFTS, 0); 6463 mac_data = er32(TDFPC); 6464 if (mac_data) 6465 ew32(TDFPC, 0); 6466 mac_data = er32(RDFH); 6467 if (mac_data) 6468 ew32(RDFH, 0); 6469 mac_data = er32(RDFT); 6470 if (mac_data) 6471 ew32(RDFT, 0); 6472 mac_data = er32(RDFHS); 6473 if (mac_data) 6474 ew32(RDFHS, 0); 6475 mac_data = er32(RDFTS); 6476 if (mac_data) 6477 ew32(RDFTS, 0); 6478 mac_data = er32(RDFPC); 6479 if (mac_data) 6480 ew32(RDFPC, 0); 6481 } 6482 6483 static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter) 6484 { 6485 struct e1000_hw *hw = &adapter->hw; 6486 bool firmware_bug = false; 6487 u32 mac_data; 6488 u16 phy_data; 6489 u32 i = 0; 6490 6491 if (er32(FWSM) & E1000_ICH_FWSM_FW_VALID && 6492 hw->mac.type >= e1000_pch_adp) { 6493 /* Keep the GPT clock enabled for CSME */ 6494 mac_data = er32(FEXTNVM); 6495 mac_data |= BIT(3); 6496 ew32(FEXTNVM, mac_data); 6497 /* Request ME unconfigure the device from S0ix */ 6498 mac_data = er32(H2ME); 6499 mac_data &= ~E1000_H2ME_START_DPG; 6500 mac_data |= E1000_H2ME_EXIT_DPG; 6501 trace_e1000e_trace_mac_register(mac_data); 6502 ew32(H2ME, mac_data); 6503 6504 /* Poll up to 2.5 seconds for ME to unconfigure DPG. 6505 * If this takes more than 1 second, show a warning indicating a 6506 * firmware bug 6507 */ 6508 while (!(er32(EXFWSM) & E1000_EXFWSM_DPG_EXIT_DONE)) { 6509 if (i > 100 && !firmware_bug) 6510 firmware_bug = true; 6511 6512 if (i++ == 250) { 6513 e_dbg("Timeout (firmware bug): %d msec\n", 6514 i * 10); 6515 break; 6516 } 6517 6518 usleep_range(10000, 11000); 6519 } 6520 if (firmware_bug) 6521 e_warn("DPG_EXIT_DONE took %d msec. This is a firmware bug\n", 6522 i * 10); 6523 else 6524 e_dbg("DPG_EXIT_DONE cleared after %d msec\n", i * 10); 6525 } else { 6526 /* Request driver unconfigure the device from S0ix */ 6527 6528 /* Disable the Dynamic Power Gating in the MAC */ 6529 mac_data = er32(FEXTNVM7); 6530 mac_data &= 0xFFBFFFFF; 6531 ew32(FEXTNVM7, mac_data); 6532 6533 /* Disable mPHY power gating for any link and speed */ 6534 mac_data = er32(FEXTNVM8); 6535 mac_data &= ~BIT(9); 6536 ew32(FEXTNVM8, mac_data); 6537 6538 /* Disable K1 off */ 6539 mac_data = er32(FEXTNVM6); 6540 mac_data &= ~BIT(31); 6541 ew32(FEXTNVM6, mac_data); 6542 6543 /* Disable Ungate PGCB clock */ 6544 mac_data = er32(FEXTNVM9); 6545 mac_data |= BIT(28); 6546 ew32(FEXTNVM9, mac_data); 6547 6548 /* Cancel not waking from dynamic 6549 * Power Gating with clock request 6550 */ 6551 mac_data = er32(FEXTNVM12); 6552 mac_data &= ~BIT(12); 6553 ew32(FEXTNVM12, mac_data); 6554 6555 /* Cancel disable disconnected cable conditioning 6556 * for Power Gating 6557 */ 6558 mac_data = er32(DPGFR); 6559 mac_data &= ~BIT(2); 6560 ew32(DPGFR, mac_data); 6561 6562 /* Disable the Dynamic Clock Gating in the DMA and MAC */ 6563 mac_data = er32(CTRL_EXT); 6564 mac_data &= 0xFFF7FFFF; 6565 ew32(CTRL_EXT, mac_data); 6566 6567 /* Revert the lanphypc logic to use the internal Gbe counter 6568 * and not the PMC counter 6569 */ 6570 mac_data = er32(FEXTNVM5); 6571 mac_data &= 0xFFFFFF7F; 6572 ew32(FEXTNVM5, mac_data); 6573 6574 /* Enable the periodic inband message, 6575 * Request PCIe clock in K1 page770_17[10:9] =01b 6576 */ 6577 e1e_rphy(hw, HV_PM_CTRL, &phy_data); 6578 phy_data &= 0xFBFF; 6579 phy_data |= HV_PM_CTRL_K1_CLK_REQ; 6580 e1e_wphy(hw, HV_PM_CTRL, phy_data); 6581 6582 /* Return back configuration 6583 * 772_29[5] = 0 CS_Mode_Stay_In_K1 6584 */ 6585 e1e_rphy(hw, I217_CGFREG, &phy_data); 6586 phy_data &= 0xFFDF; 6587 e1e_wphy(hw, I217_CGFREG, phy_data); 6588 6589 /* Change the MAC/PHY interface to Kumeran 6590 * Unforce the SMBus in PHY page769_23[0] = 0 6591 * Unforce the SMBus in MAC CTRL_EXT[11] = 0 6592 */ 6593 e1e_rphy(hw, CV_SMB_CTRL, &phy_data); 6594 phy_data &= ~CV_SMB_CTRL_FORCE_SMBUS; 6595 e1e_wphy(hw, CV_SMB_CTRL, phy_data); 6596 mac_data = er32(CTRL_EXT); 6597 mac_data &= ~E1000_CTRL_EXT_FORCE_SMBUS; 6598 ew32(CTRL_EXT, mac_data); 6599 } 6600 6601 /* Disable Dynamic Power Gating */ 6602 mac_data = er32(CTRL_EXT); 6603 mac_data &= 0xFFFFFFF7; 6604 ew32(CTRL_EXT, mac_data); 6605 6606 /* Enable the time synchronization clock */ 6607 mac_data = er32(FEXTNVM7); 6608 mac_data &= ~BIT(31); 6609 mac_data |= BIT(0); 6610 ew32(FEXTNVM7, mac_data); 6611 } 6612 6613 static int e1000e_pm_freeze(struct device *dev) 6614 { 6615 struct net_device *netdev = dev_get_drvdata(dev); 6616 struct e1000_adapter *adapter = netdev_priv(netdev); 6617 bool present; 6618 6619 rtnl_lock(); 6620 6621 present = netif_device_present(netdev); 6622 netif_device_detach(netdev); 6623 6624 if (present && netif_running(netdev)) { 6625 int count = E1000_CHECK_RESET_COUNT; 6626 6627 while (test_bit(__E1000_RESETTING, &adapter->state) && count--) 6628 usleep_range(10000, 11000); 6629 6630 WARN_ON(test_bit(__E1000_RESETTING, &adapter->state)); 6631 6632 /* Quiesce the device without resetting the hardware */ 6633 e1000e_down(adapter, false); 6634 e1000_free_irq(adapter); 6635 } 6636 rtnl_unlock(); 6637 6638 e1000e_reset_interrupt_capability(adapter); 6639 6640 /* Allow time for pending master requests to run */ 6641 e1000e_disable_pcie_master(&adapter->hw); 6642 6643 return 0; 6644 } 6645 6646 static int __e1000_shutdown(struct pci_dev *pdev, bool runtime) 6647 { 6648 struct net_device *netdev = pci_get_drvdata(pdev); 6649 struct e1000_adapter *adapter = netdev_priv(netdev); 6650 struct e1000_hw *hw = &adapter->hw; 6651 u32 ctrl, ctrl_ext, rctl, status, wufc; 6652 int retval = 0; 6653 6654 /* Runtime suspend should only enable wakeup for link changes */ 6655 if (runtime) 6656 wufc = E1000_WUFC_LNKC; 6657 else if (device_may_wakeup(&pdev->dev)) 6658 wufc = adapter->wol; 6659 else 6660 wufc = 0; 6661 6662 status = er32(STATUS); 6663 if (status & E1000_STATUS_LU) 6664 wufc &= ~E1000_WUFC_LNKC; 6665 6666 if (wufc) { 6667 e1000_setup_rctl(adapter); 6668 e1000e_set_rx_mode(netdev); 6669 6670 /* turn on all-multi mode if wake on multicast is enabled */ 6671 if (wufc & E1000_WUFC_MC) { 6672 rctl = er32(RCTL); 6673 rctl |= E1000_RCTL_MPE; 6674 ew32(RCTL, rctl); 6675 } 6676 6677 ctrl = er32(CTRL); 6678 ctrl |= E1000_CTRL_ADVD3WUC; 6679 if (!(adapter->flags2 & FLAG2_HAS_PHY_WAKEUP)) 6680 ctrl |= E1000_CTRL_EN_PHY_PWR_MGMT; 6681 ew32(CTRL, ctrl); 6682 6683 if (adapter->hw.phy.media_type == e1000_media_type_fiber || 6684 adapter->hw.phy.media_type == 6685 e1000_media_type_internal_serdes) { 6686 /* keep the laser running in D3 */ 6687 ctrl_ext = er32(CTRL_EXT); 6688 ctrl_ext |= E1000_CTRL_EXT_SDP3_DATA; 6689 ew32(CTRL_EXT, ctrl_ext); 6690 } 6691 6692 if (!runtime) 6693 e1000e_power_up_phy(adapter); 6694 6695 if (adapter->flags & FLAG_IS_ICH) 6696 e1000_suspend_workarounds_ich8lan(&adapter->hw); 6697 6698 if (adapter->flags2 & FLAG2_HAS_PHY_WAKEUP) { 6699 /* enable wakeup by the PHY */ 6700 retval = e1000_init_phy_wakeup(adapter, wufc); 6701 if (retval) 6702 return retval; 6703 } else { 6704 /* enable wakeup by the MAC */ 6705 ew32(WUFC, wufc); 6706 ew32(WUC, E1000_WUC_PME_EN); 6707 } 6708 } else { 6709 ew32(WUC, 0); 6710 ew32(WUFC, 0); 6711 6712 e1000_power_down_phy(adapter); 6713 } 6714 6715 if (adapter->hw.phy.type == e1000_phy_igp_3) { 6716 e1000e_igp3_phy_powerdown_workaround_ich8lan(&adapter->hw); 6717 } else if (hw->mac.type >= e1000_pch_lpt) { 6718 if (wufc && !(wufc & (E1000_WUFC_EX | E1000_WUFC_MC | E1000_WUFC_BC))) 6719 /* ULP does not support wake from unicast, multicast 6720 * or broadcast. 6721 */ 6722 retval = e1000_enable_ulp_lpt_lp(hw, !runtime); 6723 6724 if (retval) 6725 return retval; 6726 } 6727 6728 /* Ensure that the appropriate bits are set in LPI_CTRL 6729 * for EEE in Sx 6730 */ 6731 if ((hw->phy.type >= e1000_phy_i217) && 6732 adapter->eee_advert && hw->dev_spec.ich8lan.eee_lp_ability) { 6733 u16 lpi_ctrl = 0; 6734 6735 retval = hw->phy.ops.acquire(hw); 6736 if (!retval) { 6737 retval = e1e_rphy_locked(hw, I82579_LPI_CTRL, 6738 &lpi_ctrl); 6739 if (!retval) { 6740 if (adapter->eee_advert & 6741 hw->dev_spec.ich8lan.eee_lp_ability & 6742 I82579_EEE_100_SUPPORTED) 6743 lpi_ctrl |= I82579_LPI_CTRL_100_ENABLE; 6744 if (adapter->eee_advert & 6745 hw->dev_spec.ich8lan.eee_lp_ability & 6746 I82579_EEE_1000_SUPPORTED) 6747 lpi_ctrl |= I82579_LPI_CTRL_1000_ENABLE; 6748 6749 retval = e1e_wphy_locked(hw, I82579_LPI_CTRL, 6750 lpi_ctrl); 6751 } 6752 } 6753 hw->phy.ops.release(hw); 6754 } 6755 6756 /* Release control of h/w to f/w. If f/w is AMT enabled, this 6757 * would have already happened in close and is redundant. 6758 */ 6759 e1000e_release_hw_control(adapter); 6760 6761 pci_clear_master(pdev); 6762 6763 /* The pci-e switch on some quad port adapters will report a 6764 * correctable error when the MAC transitions from D0 to D3. To 6765 * prevent this we need to mask off the correctable errors on the 6766 * downstream port of the pci-e switch. 6767 * 6768 * We don't have the associated upstream bridge while assigning 6769 * the PCI device into guest. For example, the KVM on power is 6770 * one of the cases. 6771 */ 6772 if (adapter->flags & FLAG_IS_QUAD_PORT) { 6773 struct pci_dev *us_dev = pdev->bus->self; 6774 u16 devctl; 6775 6776 if (!us_dev) 6777 return 0; 6778 6779 pcie_capability_read_word(us_dev, PCI_EXP_DEVCTL, &devctl); 6780 pcie_capability_write_word(us_dev, PCI_EXP_DEVCTL, 6781 (devctl & ~PCI_EXP_DEVCTL_CERE)); 6782 6783 pci_save_state(pdev); 6784 pci_prepare_to_sleep(pdev); 6785 6786 pcie_capability_write_word(us_dev, PCI_EXP_DEVCTL, devctl); 6787 } 6788 6789 return 0; 6790 } 6791 6792 /** 6793 * __e1000e_disable_aspm - Disable ASPM states 6794 * @pdev: pointer to PCI device struct 6795 * @state: bit-mask of ASPM states to disable 6796 * @locked: indication if this context holds pci_bus_sem locked. 6797 * 6798 * Some devices *must* have certain ASPM states disabled per hardware errata. 6799 **/ 6800 static void __e1000e_disable_aspm(struct pci_dev *pdev, u16 state, int locked) 6801 { 6802 struct pci_dev *parent = pdev->bus->self; 6803 u16 aspm_dis_mask = 0; 6804 u16 pdev_aspmc, parent_aspmc; 6805 6806 switch (state) { 6807 case PCIE_LINK_STATE_L0S: 6808 case PCIE_LINK_STATE_L0S | PCIE_LINK_STATE_L1: 6809 aspm_dis_mask |= PCI_EXP_LNKCTL_ASPM_L0S; 6810 fallthrough; /* can't have L1 without L0s */ 6811 case PCIE_LINK_STATE_L1: 6812 aspm_dis_mask |= PCI_EXP_LNKCTL_ASPM_L1; 6813 break; 6814 default: 6815 return; 6816 } 6817 6818 pcie_capability_read_word(pdev, PCI_EXP_LNKCTL, &pdev_aspmc); 6819 pdev_aspmc &= PCI_EXP_LNKCTL_ASPMC; 6820 6821 if (parent) { 6822 pcie_capability_read_word(parent, PCI_EXP_LNKCTL, 6823 &parent_aspmc); 6824 parent_aspmc &= PCI_EXP_LNKCTL_ASPMC; 6825 } 6826 6827 /* Nothing to do if the ASPM states to be disabled already are */ 6828 if (!(pdev_aspmc & aspm_dis_mask) && 6829 (!parent || !(parent_aspmc & aspm_dis_mask))) 6830 return; 6831 6832 dev_info(&pdev->dev, "Disabling ASPM %s %s\n", 6833 (aspm_dis_mask & pdev_aspmc & PCI_EXP_LNKCTL_ASPM_L0S) ? 6834 "L0s" : "", 6835 (aspm_dis_mask & pdev_aspmc & PCI_EXP_LNKCTL_ASPM_L1) ? 6836 "L1" : ""); 6837 6838 #ifdef CONFIG_PCIEASPM 6839 if (locked) 6840 pci_disable_link_state_locked(pdev, state); 6841 else 6842 pci_disable_link_state(pdev, state); 6843 6844 /* Double-check ASPM control. If not disabled by the above, the 6845 * BIOS is preventing that from happening (or CONFIG_PCIEASPM is 6846 * not enabled); override by writing PCI config space directly. 6847 */ 6848 pcie_capability_read_word(pdev, PCI_EXP_LNKCTL, &pdev_aspmc); 6849 pdev_aspmc &= PCI_EXP_LNKCTL_ASPMC; 6850 6851 if (!(aspm_dis_mask & pdev_aspmc)) 6852 return; 6853 #endif 6854 6855 /* Both device and parent should have the same ASPM setting. 6856 * Disable ASPM in downstream component first and then upstream. 6857 */ 6858 pcie_capability_clear_word(pdev, PCI_EXP_LNKCTL, aspm_dis_mask); 6859 6860 if (parent) 6861 pcie_capability_clear_word(parent, PCI_EXP_LNKCTL, 6862 aspm_dis_mask); 6863 } 6864 6865 /** 6866 * e1000e_disable_aspm - Disable ASPM states. 6867 * @pdev: pointer to PCI device struct 6868 * @state: bit-mask of ASPM states to disable 6869 * 6870 * This function acquires the pci_bus_sem! 6871 * Some devices *must* have certain ASPM states disabled per hardware errata. 6872 **/ 6873 static void e1000e_disable_aspm(struct pci_dev *pdev, u16 state) 6874 { 6875 __e1000e_disable_aspm(pdev, state, 0); 6876 } 6877 6878 /** 6879 * e1000e_disable_aspm_locked - Disable ASPM states. 6880 * @pdev: pointer to PCI device struct 6881 * @state: bit-mask of ASPM states to disable 6882 * 6883 * This function must be called with pci_bus_sem acquired! 6884 * Some devices *must* have certain ASPM states disabled per hardware errata. 6885 **/ 6886 static void e1000e_disable_aspm_locked(struct pci_dev *pdev, u16 state) 6887 { 6888 __e1000e_disable_aspm(pdev, state, 1); 6889 } 6890 6891 static int e1000e_pm_thaw(struct device *dev) 6892 { 6893 struct net_device *netdev = dev_get_drvdata(dev); 6894 struct e1000_adapter *adapter = netdev_priv(netdev); 6895 int rc = 0; 6896 6897 e1000e_set_interrupt_capability(adapter); 6898 6899 rtnl_lock(); 6900 if (netif_running(netdev)) { 6901 rc = e1000_request_irq(adapter); 6902 if (rc) 6903 goto err_irq; 6904 6905 e1000e_up(adapter); 6906 } 6907 6908 netif_device_attach(netdev); 6909 err_irq: 6910 rtnl_unlock(); 6911 6912 return rc; 6913 } 6914 6915 static int __e1000_resume(struct pci_dev *pdev) 6916 { 6917 struct net_device *netdev = pci_get_drvdata(pdev); 6918 struct e1000_adapter *adapter = netdev_priv(netdev); 6919 struct e1000_hw *hw = &adapter->hw; 6920 u16 aspm_disable_flag = 0; 6921 6922 if (adapter->flags2 & FLAG2_DISABLE_ASPM_L0S) 6923 aspm_disable_flag = PCIE_LINK_STATE_L0S; 6924 if (adapter->flags2 & FLAG2_DISABLE_ASPM_L1) 6925 aspm_disable_flag |= PCIE_LINK_STATE_L1; 6926 if (aspm_disable_flag) 6927 e1000e_disable_aspm(pdev, aspm_disable_flag); 6928 6929 pci_set_master(pdev); 6930 6931 if (hw->mac.type >= e1000_pch2lan) 6932 e1000_resume_workarounds_pchlan(&adapter->hw); 6933 6934 e1000e_power_up_phy(adapter); 6935 6936 /* report the system wakeup cause from S3/S4 */ 6937 if (adapter->flags2 & FLAG2_HAS_PHY_WAKEUP) { 6938 u16 phy_data; 6939 6940 e1e_rphy(&adapter->hw, BM_WUS, &phy_data); 6941 if (phy_data) { 6942 e_info("PHY Wakeup cause - %s\n", 6943 phy_data & E1000_WUS_EX ? "Unicast Packet" : 6944 phy_data & E1000_WUS_MC ? "Multicast Packet" : 6945 phy_data & E1000_WUS_BC ? "Broadcast Packet" : 6946 phy_data & E1000_WUS_MAG ? "Magic Packet" : 6947 phy_data & E1000_WUS_LNKC ? 6948 "Link Status Change" : "other"); 6949 } 6950 e1e_wphy(&adapter->hw, BM_WUS, ~0); 6951 } else { 6952 u32 wus = er32(WUS); 6953 6954 if (wus) { 6955 e_info("MAC Wakeup cause - %s\n", 6956 wus & E1000_WUS_EX ? "Unicast Packet" : 6957 wus & E1000_WUS_MC ? "Multicast Packet" : 6958 wus & E1000_WUS_BC ? "Broadcast Packet" : 6959 wus & E1000_WUS_MAG ? "Magic Packet" : 6960 wus & E1000_WUS_LNKC ? "Link Status Change" : 6961 "other"); 6962 } 6963 ew32(WUS, ~0); 6964 } 6965 6966 e1000e_reset(adapter); 6967 6968 e1000_init_manageability_pt(adapter); 6969 6970 /* If the controller has AMT, do not set DRV_LOAD until the interface 6971 * is up. For all other cases, let the f/w know that the h/w is now 6972 * under the control of the driver. 6973 */ 6974 if (!(adapter->flags & FLAG_HAS_AMT)) 6975 e1000e_get_hw_control(adapter); 6976 6977 return 0; 6978 } 6979 6980 static __maybe_unused int e1000e_pm_prepare(struct device *dev) 6981 { 6982 return pm_runtime_suspended(dev) && 6983 pm_suspend_via_firmware(); 6984 } 6985 6986 static __maybe_unused int e1000e_pm_suspend(struct device *dev) 6987 { 6988 struct net_device *netdev = pci_get_drvdata(to_pci_dev(dev)); 6989 struct e1000_adapter *adapter = netdev_priv(netdev); 6990 struct pci_dev *pdev = to_pci_dev(dev); 6991 int rc; 6992 6993 e1000e_flush_lpic(pdev); 6994 6995 e1000e_pm_freeze(dev); 6996 6997 rc = __e1000_shutdown(pdev, false); 6998 if (rc) { 6999 e1000e_pm_thaw(dev); 7000 } else { 7001 /* Introduce S0ix implementation */ 7002 if (adapter->flags2 & FLAG2_ENABLE_S0IX_FLOWS) 7003 e1000e_s0ix_entry_flow(adapter); 7004 } 7005 7006 return rc; 7007 } 7008 7009 static __maybe_unused int e1000e_pm_resume(struct device *dev) 7010 { 7011 struct net_device *netdev = pci_get_drvdata(to_pci_dev(dev)); 7012 struct e1000_adapter *adapter = netdev_priv(netdev); 7013 struct pci_dev *pdev = to_pci_dev(dev); 7014 int rc; 7015 7016 /* Introduce S0ix implementation */ 7017 if (adapter->flags2 & FLAG2_ENABLE_S0IX_FLOWS) 7018 e1000e_s0ix_exit_flow(adapter); 7019 7020 rc = __e1000_resume(pdev); 7021 if (rc) 7022 return rc; 7023 7024 return e1000e_pm_thaw(dev); 7025 } 7026 7027 static __maybe_unused int e1000e_pm_runtime_idle(struct device *dev) 7028 { 7029 struct net_device *netdev = dev_get_drvdata(dev); 7030 struct e1000_adapter *adapter = netdev_priv(netdev); 7031 u16 eee_lp; 7032 7033 eee_lp = adapter->hw.dev_spec.ich8lan.eee_lp_ability; 7034 7035 if (!e1000e_has_link(adapter)) { 7036 adapter->hw.dev_spec.ich8lan.eee_lp_ability = eee_lp; 7037 pm_schedule_suspend(dev, 5 * MSEC_PER_SEC); 7038 } 7039 7040 return -EBUSY; 7041 } 7042 7043 static __maybe_unused int e1000e_pm_runtime_resume(struct device *dev) 7044 { 7045 struct pci_dev *pdev = to_pci_dev(dev); 7046 struct net_device *netdev = pci_get_drvdata(pdev); 7047 struct e1000_adapter *adapter = netdev_priv(netdev); 7048 int rc; 7049 7050 rc = __e1000_resume(pdev); 7051 if (rc) 7052 return rc; 7053 7054 if (netdev->flags & IFF_UP) 7055 e1000e_up(adapter); 7056 7057 return rc; 7058 } 7059 7060 static __maybe_unused int e1000e_pm_runtime_suspend(struct device *dev) 7061 { 7062 struct pci_dev *pdev = to_pci_dev(dev); 7063 struct net_device *netdev = pci_get_drvdata(pdev); 7064 struct e1000_adapter *adapter = netdev_priv(netdev); 7065 7066 if (netdev->flags & IFF_UP) { 7067 int count = E1000_CHECK_RESET_COUNT; 7068 7069 while (test_bit(__E1000_RESETTING, &adapter->state) && count--) 7070 usleep_range(10000, 11000); 7071 7072 WARN_ON(test_bit(__E1000_RESETTING, &adapter->state)); 7073 7074 /* Down the device without resetting the hardware */ 7075 e1000e_down(adapter, false); 7076 } 7077 7078 if (__e1000_shutdown(pdev, true)) { 7079 e1000e_pm_runtime_resume(dev); 7080 return -EBUSY; 7081 } 7082 7083 return 0; 7084 } 7085 7086 static void e1000_shutdown(struct pci_dev *pdev) 7087 { 7088 e1000e_flush_lpic(pdev); 7089 7090 e1000e_pm_freeze(&pdev->dev); 7091 7092 __e1000_shutdown(pdev, false); 7093 } 7094 7095 #ifdef CONFIG_NET_POLL_CONTROLLER 7096 7097 static irqreturn_t e1000_intr_msix(int __always_unused irq, void *data) 7098 { 7099 struct net_device *netdev = data; 7100 struct e1000_adapter *adapter = netdev_priv(netdev); 7101 7102 if (adapter->msix_entries) { 7103 int vector, msix_irq; 7104 7105 vector = 0; 7106 msix_irq = adapter->msix_entries[vector].vector; 7107 if (disable_hardirq(msix_irq)) 7108 e1000_intr_msix_rx(msix_irq, netdev); 7109 enable_irq(msix_irq); 7110 7111 vector++; 7112 msix_irq = adapter->msix_entries[vector].vector; 7113 if (disable_hardirq(msix_irq)) 7114 e1000_intr_msix_tx(msix_irq, netdev); 7115 enable_irq(msix_irq); 7116 7117 vector++; 7118 msix_irq = adapter->msix_entries[vector].vector; 7119 if (disable_hardirq(msix_irq)) 7120 e1000_msix_other(msix_irq, netdev); 7121 enable_irq(msix_irq); 7122 } 7123 7124 return IRQ_HANDLED; 7125 } 7126 7127 /** 7128 * e1000_netpoll 7129 * @netdev: network interface device structure 7130 * 7131 * Polling 'interrupt' - used by things like netconsole to send skbs 7132 * without having to re-enable interrupts. It's not called while 7133 * the interrupt routine is executing. 7134 */ 7135 static void e1000_netpoll(struct net_device *netdev) 7136 { 7137 struct e1000_adapter *adapter = netdev_priv(netdev); 7138 7139 switch (adapter->int_mode) { 7140 case E1000E_INT_MODE_MSIX: 7141 e1000_intr_msix(adapter->pdev->irq, netdev); 7142 break; 7143 case E1000E_INT_MODE_MSI: 7144 if (disable_hardirq(adapter->pdev->irq)) 7145 e1000_intr_msi(adapter->pdev->irq, netdev); 7146 enable_irq(adapter->pdev->irq); 7147 break; 7148 default: /* E1000E_INT_MODE_LEGACY */ 7149 if (disable_hardirq(adapter->pdev->irq)) 7150 e1000_intr(adapter->pdev->irq, netdev); 7151 enable_irq(adapter->pdev->irq); 7152 break; 7153 } 7154 } 7155 #endif 7156 7157 /** 7158 * e1000_io_error_detected - called when PCI error is detected 7159 * @pdev: Pointer to PCI device 7160 * @state: The current pci connection state 7161 * 7162 * This function is called after a PCI bus error affecting 7163 * this device has been detected. 7164 */ 7165 static pci_ers_result_t e1000_io_error_detected(struct pci_dev *pdev, 7166 pci_channel_state_t state) 7167 { 7168 e1000e_pm_freeze(&pdev->dev); 7169 7170 if (state == pci_channel_io_perm_failure) 7171 return PCI_ERS_RESULT_DISCONNECT; 7172 7173 pci_disable_device(pdev); 7174 7175 /* Request a slot reset. */ 7176 return PCI_ERS_RESULT_NEED_RESET; 7177 } 7178 7179 /** 7180 * e1000_io_slot_reset - called after the pci bus has been reset. 7181 * @pdev: Pointer to PCI device 7182 * 7183 * Restart the card from scratch, as if from a cold-boot. Implementation 7184 * resembles the first-half of the e1000e_pm_resume routine. 7185 */ 7186 static pci_ers_result_t e1000_io_slot_reset(struct pci_dev *pdev) 7187 { 7188 struct net_device *netdev = pci_get_drvdata(pdev); 7189 struct e1000_adapter *adapter = netdev_priv(netdev); 7190 struct e1000_hw *hw = &adapter->hw; 7191 u16 aspm_disable_flag = 0; 7192 int err; 7193 pci_ers_result_t result; 7194 7195 if (adapter->flags2 & FLAG2_DISABLE_ASPM_L0S) 7196 aspm_disable_flag = PCIE_LINK_STATE_L0S; 7197 if (adapter->flags2 & FLAG2_DISABLE_ASPM_L1) 7198 aspm_disable_flag |= PCIE_LINK_STATE_L1; 7199 if (aspm_disable_flag) 7200 e1000e_disable_aspm_locked(pdev, aspm_disable_flag); 7201 7202 err = pci_enable_device_mem(pdev); 7203 if (err) { 7204 dev_err(&pdev->dev, 7205 "Cannot re-enable PCI device after reset.\n"); 7206 result = PCI_ERS_RESULT_DISCONNECT; 7207 } else { 7208 pdev->state_saved = true; 7209 pci_restore_state(pdev); 7210 pci_set_master(pdev); 7211 7212 pci_enable_wake(pdev, PCI_D3hot, 0); 7213 pci_enable_wake(pdev, PCI_D3cold, 0); 7214 7215 e1000e_reset(adapter); 7216 ew32(WUS, ~0); 7217 result = PCI_ERS_RESULT_RECOVERED; 7218 } 7219 7220 return result; 7221 } 7222 7223 /** 7224 * e1000_io_resume - called when traffic can start flowing again. 7225 * @pdev: Pointer to PCI device 7226 * 7227 * This callback is called when the error recovery driver tells us that 7228 * its OK to resume normal operation. Implementation resembles the 7229 * second-half of the e1000e_pm_resume routine. 7230 */ 7231 static void e1000_io_resume(struct pci_dev *pdev) 7232 { 7233 struct net_device *netdev = pci_get_drvdata(pdev); 7234 struct e1000_adapter *adapter = netdev_priv(netdev); 7235 7236 e1000_init_manageability_pt(adapter); 7237 7238 e1000e_pm_thaw(&pdev->dev); 7239 7240 /* If the controller has AMT, do not set DRV_LOAD until the interface 7241 * is up. For all other cases, let the f/w know that the h/w is now 7242 * under the control of the driver. 7243 */ 7244 if (!(adapter->flags & FLAG_HAS_AMT)) 7245 e1000e_get_hw_control(adapter); 7246 } 7247 7248 static void e1000_print_device_info(struct e1000_adapter *adapter) 7249 { 7250 struct e1000_hw *hw = &adapter->hw; 7251 struct net_device *netdev = adapter->netdev; 7252 u32 ret_val; 7253 u8 pba_str[E1000_PBANUM_LENGTH]; 7254 7255 /* print bus type/speed/width info */ 7256 e_info("(PCI Express:2.5GT/s:%s) %pM\n", 7257 /* bus width */ 7258 ((hw->bus.width == e1000_bus_width_pcie_x4) ? "Width x4" : 7259 "Width x1"), 7260 /* MAC address */ 7261 netdev->dev_addr); 7262 e_info("Intel(R) PRO/%s Network Connection\n", 7263 (hw->phy.type == e1000_phy_ife) ? "10/100" : "1000"); 7264 ret_val = e1000_read_pba_string_generic(hw, pba_str, 7265 E1000_PBANUM_LENGTH); 7266 if (ret_val) 7267 strscpy((char *)pba_str, "Unknown", sizeof(pba_str)); 7268 e_info("MAC: %d, PHY: %d, PBA No: %s\n", 7269 hw->mac.type, hw->phy.type, pba_str); 7270 } 7271 7272 static void e1000_eeprom_checks(struct e1000_adapter *adapter) 7273 { 7274 struct e1000_hw *hw = &adapter->hw; 7275 int ret_val; 7276 u16 buf = 0; 7277 7278 if (hw->mac.type != e1000_82573) 7279 return; 7280 7281 ret_val = e1000_read_nvm(hw, NVM_INIT_CONTROL2_REG, 1, &buf); 7282 le16_to_cpus(&buf); 7283 if (!ret_val && (!(buf & BIT(0)))) { 7284 /* Deep Smart Power Down (DSPD) */ 7285 dev_warn(&adapter->pdev->dev, 7286 "Warning: detected DSPD enabled in EEPROM\n"); 7287 } 7288 } 7289 7290 static netdev_features_t e1000_fix_features(struct net_device *netdev, 7291 netdev_features_t features) 7292 { 7293 struct e1000_adapter *adapter = netdev_priv(netdev); 7294 struct e1000_hw *hw = &adapter->hw; 7295 7296 /* Jumbo frame workaround on 82579 and newer requires CRC be stripped */ 7297 if ((hw->mac.type >= e1000_pch2lan) && (netdev->mtu > ETH_DATA_LEN)) 7298 features &= ~NETIF_F_RXFCS; 7299 7300 /* Since there is no support for separate Rx/Tx vlan accel 7301 * enable/disable make sure Tx flag is always in same state as Rx. 7302 */ 7303 if (features & NETIF_F_HW_VLAN_CTAG_RX) 7304 features |= NETIF_F_HW_VLAN_CTAG_TX; 7305 else 7306 features &= ~NETIF_F_HW_VLAN_CTAG_TX; 7307 7308 return features; 7309 } 7310 7311 static int e1000_set_features(struct net_device *netdev, 7312 netdev_features_t features) 7313 { 7314 struct e1000_adapter *adapter = netdev_priv(netdev); 7315 netdev_features_t changed = features ^ netdev->features; 7316 7317 if (changed & (NETIF_F_TSO | NETIF_F_TSO6)) 7318 adapter->flags |= FLAG_TSO_FORCE; 7319 7320 if (!(changed & (NETIF_F_HW_VLAN_CTAG_RX | NETIF_F_HW_VLAN_CTAG_TX | 7321 NETIF_F_RXCSUM | NETIF_F_RXHASH | NETIF_F_RXFCS | 7322 NETIF_F_RXALL))) 7323 return 0; 7324 7325 if (changed & NETIF_F_RXFCS) { 7326 if (features & NETIF_F_RXFCS) { 7327 adapter->flags2 &= ~FLAG2_CRC_STRIPPING; 7328 } else { 7329 /* We need to take it back to defaults, which might mean 7330 * stripping is still disabled at the adapter level. 7331 */ 7332 if (adapter->flags2 & FLAG2_DFLT_CRC_STRIPPING) 7333 adapter->flags2 |= FLAG2_CRC_STRIPPING; 7334 else 7335 adapter->flags2 &= ~FLAG2_CRC_STRIPPING; 7336 } 7337 } 7338 7339 netdev->features = features; 7340 7341 if (netif_running(netdev)) 7342 e1000e_reinit_locked(adapter); 7343 else 7344 e1000e_reset(adapter); 7345 7346 return 1; 7347 } 7348 7349 static const struct net_device_ops e1000e_netdev_ops = { 7350 .ndo_open = e1000e_open, 7351 .ndo_stop = e1000e_close, 7352 .ndo_start_xmit = e1000_xmit_frame, 7353 .ndo_get_stats64 = e1000e_get_stats64, 7354 .ndo_set_rx_mode = e1000e_set_rx_mode, 7355 .ndo_set_mac_address = e1000_set_mac, 7356 .ndo_change_mtu = e1000_change_mtu, 7357 .ndo_eth_ioctl = e1000_ioctl, 7358 .ndo_tx_timeout = e1000_tx_timeout, 7359 .ndo_validate_addr = eth_validate_addr, 7360 7361 .ndo_vlan_rx_add_vid = e1000_vlan_rx_add_vid, 7362 .ndo_vlan_rx_kill_vid = e1000_vlan_rx_kill_vid, 7363 #ifdef CONFIG_NET_POLL_CONTROLLER 7364 .ndo_poll_controller = e1000_netpoll, 7365 #endif 7366 .ndo_set_features = e1000_set_features, 7367 .ndo_fix_features = e1000_fix_features, 7368 .ndo_features_check = passthru_features_check, 7369 }; 7370 7371 /** 7372 * e1000_probe - Device Initialization Routine 7373 * @pdev: PCI device information struct 7374 * @ent: entry in e1000_pci_tbl 7375 * 7376 * Returns 0 on success, negative on failure 7377 * 7378 * e1000_probe initializes an adapter identified by a pci_dev structure. 7379 * The OS initialization, configuring of the adapter private structure, 7380 * and a hardware reset occur. 7381 **/ 7382 static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent) 7383 { 7384 struct net_device *netdev; 7385 struct e1000_adapter *adapter; 7386 struct e1000_hw *hw; 7387 const struct e1000_info *ei = e1000_info_tbl[ent->driver_data]; 7388 resource_size_t mmio_start, mmio_len; 7389 resource_size_t flash_start, flash_len; 7390 static int cards_found; 7391 u16 aspm_disable_flag = 0; 7392 u16 eeprom_data = 0; 7393 u16 eeprom_apme_mask = E1000_EEPROM_APME; 7394 int bars, i, err; 7395 s32 ret_val = 0; 7396 7397 if (ei->flags2 & FLAG2_DISABLE_ASPM_L0S) 7398 aspm_disable_flag = PCIE_LINK_STATE_L0S; 7399 if (ei->flags2 & FLAG2_DISABLE_ASPM_L1) 7400 aspm_disable_flag |= PCIE_LINK_STATE_L1; 7401 if (aspm_disable_flag) 7402 e1000e_disable_aspm(pdev, aspm_disable_flag); 7403 7404 err = pci_enable_device_mem(pdev); 7405 if (err) 7406 return err; 7407 7408 err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64)); 7409 if (err) { 7410 dev_err(&pdev->dev, 7411 "No usable DMA configuration, aborting\n"); 7412 goto err_dma; 7413 } 7414 7415 bars = pci_select_bars(pdev, IORESOURCE_MEM); 7416 err = pci_request_selected_regions_exclusive(pdev, bars, 7417 e1000e_driver_name); 7418 if (err) 7419 goto err_pci_reg; 7420 7421 /* AER (Advanced Error Reporting) hooks */ 7422 pci_enable_pcie_error_reporting(pdev); 7423 7424 pci_set_master(pdev); 7425 /* PCI config space info */ 7426 err = pci_save_state(pdev); 7427 if (err) 7428 goto err_alloc_etherdev; 7429 7430 err = -ENOMEM; 7431 netdev = alloc_etherdev(sizeof(struct e1000_adapter)); 7432 if (!netdev) 7433 goto err_alloc_etherdev; 7434 7435 SET_NETDEV_DEV(netdev, &pdev->dev); 7436 7437 netdev->irq = pdev->irq; 7438 7439 pci_set_drvdata(pdev, netdev); 7440 adapter = netdev_priv(netdev); 7441 hw = &adapter->hw; 7442 adapter->netdev = netdev; 7443 adapter->pdev = pdev; 7444 adapter->ei = ei; 7445 adapter->pba = ei->pba; 7446 adapter->flags = ei->flags; 7447 adapter->flags2 = ei->flags2; 7448 adapter->hw.adapter = adapter; 7449 adapter->hw.mac.type = ei->mac; 7450 adapter->max_hw_frame_size = ei->max_hw_frame_size; 7451 adapter->msg_enable = netif_msg_init(debug, DEFAULT_MSG_ENABLE); 7452 7453 mmio_start = pci_resource_start(pdev, 0); 7454 mmio_len = pci_resource_len(pdev, 0); 7455 7456 err = -EIO; 7457 adapter->hw.hw_addr = ioremap(mmio_start, mmio_len); 7458 if (!adapter->hw.hw_addr) 7459 goto err_ioremap; 7460 7461 if ((adapter->flags & FLAG_HAS_FLASH) && 7462 (pci_resource_flags(pdev, 1) & IORESOURCE_MEM) && 7463 (hw->mac.type < e1000_pch_spt)) { 7464 flash_start = pci_resource_start(pdev, 1); 7465 flash_len = pci_resource_len(pdev, 1); 7466 adapter->hw.flash_address = ioremap(flash_start, flash_len); 7467 if (!adapter->hw.flash_address) 7468 goto err_flashmap; 7469 } 7470 7471 /* Set default EEE advertisement */ 7472 if (adapter->flags2 & FLAG2_HAS_EEE) 7473 adapter->eee_advert = MDIO_EEE_100TX | MDIO_EEE_1000T; 7474 7475 /* construct the net_device struct */ 7476 netdev->netdev_ops = &e1000e_netdev_ops; 7477 e1000e_set_ethtool_ops(netdev); 7478 netdev->watchdog_timeo = 5 * HZ; 7479 netif_napi_add(netdev, &adapter->napi, e1000e_poll); 7480 strscpy(netdev->name, pci_name(pdev), sizeof(netdev->name)); 7481 7482 netdev->mem_start = mmio_start; 7483 netdev->mem_end = mmio_start + mmio_len; 7484 7485 adapter->bd_number = cards_found++; 7486 7487 e1000e_check_options(adapter); 7488 7489 /* setup adapter struct */ 7490 err = e1000_sw_init(adapter); 7491 if (err) 7492 goto err_sw_init; 7493 7494 memcpy(&hw->mac.ops, ei->mac_ops, sizeof(hw->mac.ops)); 7495 memcpy(&hw->nvm.ops, ei->nvm_ops, sizeof(hw->nvm.ops)); 7496 memcpy(&hw->phy.ops, ei->phy_ops, sizeof(hw->phy.ops)); 7497 7498 err = ei->get_variants(adapter); 7499 if (err) 7500 goto err_hw_init; 7501 7502 if ((adapter->flags & FLAG_IS_ICH) && 7503 (adapter->flags & FLAG_READ_ONLY_NVM) && 7504 (hw->mac.type < e1000_pch_spt)) 7505 e1000e_write_protect_nvm_ich8lan(&adapter->hw); 7506 7507 hw->mac.ops.get_bus_info(&adapter->hw); 7508 7509 adapter->hw.phy.autoneg_wait_to_complete = 0; 7510 7511 /* Copper options */ 7512 if (adapter->hw.phy.media_type == e1000_media_type_copper) { 7513 adapter->hw.phy.mdix = AUTO_ALL_MODES; 7514 adapter->hw.phy.disable_polarity_correction = 0; 7515 adapter->hw.phy.ms_type = e1000_ms_hw_default; 7516 } 7517 7518 if (hw->phy.ops.check_reset_block && hw->phy.ops.check_reset_block(hw)) 7519 dev_info(&pdev->dev, 7520 "PHY reset is blocked due to SOL/IDER session.\n"); 7521 7522 /* Set initial default active device features */ 7523 netdev->features = (NETIF_F_SG | 7524 NETIF_F_HW_VLAN_CTAG_RX | 7525 NETIF_F_HW_VLAN_CTAG_TX | 7526 NETIF_F_TSO | 7527 NETIF_F_TSO6 | 7528 NETIF_F_RXHASH | 7529 NETIF_F_RXCSUM | 7530 NETIF_F_HW_CSUM); 7531 7532 /* Set user-changeable features (subset of all device features) */ 7533 netdev->hw_features = netdev->features; 7534 netdev->hw_features |= NETIF_F_RXFCS; 7535 netdev->priv_flags |= IFF_SUPP_NOFCS; 7536 netdev->hw_features |= NETIF_F_RXALL; 7537 7538 if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) 7539 netdev->features |= NETIF_F_HW_VLAN_CTAG_FILTER; 7540 7541 netdev->vlan_features |= (NETIF_F_SG | 7542 NETIF_F_TSO | 7543 NETIF_F_TSO6 | 7544 NETIF_F_HW_CSUM); 7545 7546 netdev->priv_flags |= IFF_UNICAST_FLT; 7547 7548 netdev->features |= NETIF_F_HIGHDMA; 7549 netdev->vlan_features |= NETIF_F_HIGHDMA; 7550 7551 /* MTU range: 68 - max_hw_frame_size */ 7552 netdev->min_mtu = ETH_MIN_MTU; 7553 netdev->max_mtu = adapter->max_hw_frame_size - 7554 (VLAN_ETH_HLEN + ETH_FCS_LEN); 7555 7556 if (e1000e_enable_mng_pass_thru(&adapter->hw)) 7557 adapter->flags |= FLAG_MNG_PT_ENABLED; 7558 7559 /* before reading the NVM, reset the controller to 7560 * put the device in a known good starting state 7561 */ 7562 adapter->hw.mac.ops.reset_hw(&adapter->hw); 7563 7564 /* systems with ASPM and others may see the checksum fail on the first 7565 * attempt. Let's give it a few tries 7566 */ 7567 for (i = 0;; i++) { 7568 if (e1000_validate_nvm_checksum(&adapter->hw) >= 0) 7569 break; 7570 if (i == 2) { 7571 dev_err(&pdev->dev, "The NVM Checksum Is Not Valid\n"); 7572 err = -EIO; 7573 goto err_eeprom; 7574 } 7575 } 7576 7577 e1000_eeprom_checks(adapter); 7578 7579 /* copy the MAC address */ 7580 if (e1000e_read_mac_addr(&adapter->hw)) 7581 dev_err(&pdev->dev, 7582 "NVM Read Error while reading MAC address\n"); 7583 7584 eth_hw_addr_set(netdev, adapter->hw.mac.addr); 7585 7586 if (!is_valid_ether_addr(netdev->dev_addr)) { 7587 dev_err(&pdev->dev, "Invalid MAC Address: %pM\n", 7588 netdev->dev_addr); 7589 err = -EIO; 7590 goto err_eeprom; 7591 } 7592 7593 timer_setup(&adapter->watchdog_timer, e1000_watchdog, 0); 7594 timer_setup(&adapter->phy_info_timer, e1000_update_phy_info, 0); 7595 7596 INIT_WORK(&adapter->reset_task, e1000_reset_task); 7597 INIT_WORK(&adapter->watchdog_task, e1000_watchdog_task); 7598 INIT_WORK(&adapter->downshift_task, e1000e_downshift_workaround); 7599 INIT_WORK(&adapter->update_phy_task, e1000e_update_phy_task); 7600 INIT_WORK(&adapter->print_hang_task, e1000_print_hw_hang); 7601 7602 /* Initialize link parameters. User can change them with ethtool */ 7603 adapter->hw.mac.autoneg = 1; 7604 adapter->fc_autoneg = true; 7605 adapter->hw.fc.requested_mode = e1000_fc_default; 7606 adapter->hw.fc.current_mode = e1000_fc_default; 7607 adapter->hw.phy.autoneg_advertised = 0x2f; 7608 7609 /* Initial Wake on LAN setting - If APM wake is enabled in 7610 * the EEPROM, enable the ACPI Magic Packet filter 7611 */ 7612 if (adapter->flags & FLAG_APME_IN_WUC) { 7613 /* APME bit in EEPROM is mapped to WUC.APME */ 7614 eeprom_data = er32(WUC); 7615 eeprom_apme_mask = E1000_WUC_APME; 7616 if ((hw->mac.type > e1000_ich10lan) && 7617 (eeprom_data & E1000_WUC_PHY_WAKE)) 7618 adapter->flags2 |= FLAG2_HAS_PHY_WAKEUP; 7619 } else if (adapter->flags & FLAG_APME_IN_CTRL3) { 7620 if (adapter->flags & FLAG_APME_CHECK_PORT_B && 7621 (adapter->hw.bus.func == 1)) 7622 ret_val = e1000_read_nvm(&adapter->hw, 7623 NVM_INIT_CONTROL3_PORT_B, 7624 1, &eeprom_data); 7625 else 7626 ret_val = e1000_read_nvm(&adapter->hw, 7627 NVM_INIT_CONTROL3_PORT_A, 7628 1, &eeprom_data); 7629 } 7630 7631 /* fetch WoL from EEPROM */ 7632 if (ret_val) 7633 e_dbg("NVM read error getting WoL initial values: %d\n", ret_val); 7634 else if (eeprom_data & eeprom_apme_mask) 7635 adapter->eeprom_wol |= E1000_WUFC_MAG; 7636 7637 /* now that we have the eeprom settings, apply the special cases 7638 * where the eeprom may be wrong or the board simply won't support 7639 * wake on lan on a particular port 7640 */ 7641 if (!(adapter->flags & FLAG_HAS_WOL)) 7642 adapter->eeprom_wol = 0; 7643 7644 /* initialize the wol settings based on the eeprom settings */ 7645 adapter->wol = adapter->eeprom_wol; 7646 7647 /* make sure adapter isn't asleep if manageability is enabled */ 7648 if (adapter->wol || (adapter->flags & FLAG_MNG_PT_ENABLED) || 7649 (hw->mac.ops.check_mng_mode(hw))) 7650 device_wakeup_enable(&pdev->dev); 7651 7652 /* save off EEPROM version number */ 7653 ret_val = e1000_read_nvm(&adapter->hw, 5, 1, &adapter->eeprom_vers); 7654 7655 if (ret_val) { 7656 e_dbg("NVM read error getting EEPROM version: %d\n", ret_val); 7657 adapter->eeprom_vers = 0; 7658 } 7659 7660 /* init PTP hardware clock */ 7661 e1000e_ptp_init(adapter); 7662 7663 /* reset the hardware with the new settings */ 7664 e1000e_reset(adapter); 7665 7666 /* If the controller has AMT, do not set DRV_LOAD until the interface 7667 * is up. For all other cases, let the f/w know that the h/w is now 7668 * under the control of the driver. 7669 */ 7670 if (!(adapter->flags & FLAG_HAS_AMT)) 7671 e1000e_get_hw_control(adapter); 7672 7673 if (hw->mac.type >= e1000_pch_cnp) 7674 adapter->flags2 |= FLAG2_ENABLE_S0IX_FLOWS; 7675 7676 strscpy(netdev->name, "eth%d", sizeof(netdev->name)); 7677 err = register_netdev(netdev); 7678 if (err) 7679 goto err_register; 7680 7681 /* carrier off reporting is important to ethtool even BEFORE open */ 7682 netif_carrier_off(netdev); 7683 7684 e1000_print_device_info(adapter); 7685 7686 dev_pm_set_driver_flags(&pdev->dev, DPM_FLAG_SMART_PREPARE); 7687 7688 if (pci_dev_run_wake(pdev) && hw->mac.type != e1000_pch_cnp) 7689 pm_runtime_put_noidle(&pdev->dev); 7690 7691 return 0; 7692 7693 err_register: 7694 if (!(adapter->flags & FLAG_HAS_AMT)) 7695 e1000e_release_hw_control(adapter); 7696 err_eeprom: 7697 if (hw->phy.ops.check_reset_block && !hw->phy.ops.check_reset_block(hw)) 7698 e1000_phy_hw_reset(&adapter->hw); 7699 err_hw_init: 7700 kfree(adapter->tx_ring); 7701 kfree(adapter->rx_ring); 7702 err_sw_init: 7703 if ((adapter->hw.flash_address) && (hw->mac.type < e1000_pch_spt)) 7704 iounmap(adapter->hw.flash_address); 7705 e1000e_reset_interrupt_capability(adapter); 7706 err_flashmap: 7707 iounmap(adapter->hw.hw_addr); 7708 err_ioremap: 7709 free_netdev(netdev); 7710 err_alloc_etherdev: 7711 pci_disable_pcie_error_reporting(pdev); 7712 pci_release_mem_regions(pdev); 7713 err_pci_reg: 7714 err_dma: 7715 pci_disable_device(pdev); 7716 return err; 7717 } 7718 7719 /** 7720 * e1000_remove - Device Removal Routine 7721 * @pdev: PCI device information struct 7722 * 7723 * e1000_remove is called by the PCI subsystem to alert the driver 7724 * that it should release a PCI device. This could be caused by a 7725 * Hot-Plug event, or because the driver is going to be removed from 7726 * memory. 7727 **/ 7728 static void e1000_remove(struct pci_dev *pdev) 7729 { 7730 struct net_device *netdev = pci_get_drvdata(pdev); 7731 struct e1000_adapter *adapter = netdev_priv(netdev); 7732 7733 e1000e_ptp_remove(adapter); 7734 7735 /* The timers may be rescheduled, so explicitly disable them 7736 * from being rescheduled. 7737 */ 7738 set_bit(__E1000_DOWN, &adapter->state); 7739 del_timer_sync(&adapter->watchdog_timer); 7740 del_timer_sync(&adapter->phy_info_timer); 7741 7742 cancel_work_sync(&adapter->reset_task); 7743 cancel_work_sync(&adapter->watchdog_task); 7744 cancel_work_sync(&adapter->downshift_task); 7745 cancel_work_sync(&adapter->update_phy_task); 7746 cancel_work_sync(&adapter->print_hang_task); 7747 7748 if (adapter->flags & FLAG_HAS_HW_TIMESTAMP) { 7749 cancel_work_sync(&adapter->tx_hwtstamp_work); 7750 if (adapter->tx_hwtstamp_skb) { 7751 dev_consume_skb_any(adapter->tx_hwtstamp_skb); 7752 adapter->tx_hwtstamp_skb = NULL; 7753 } 7754 } 7755 7756 unregister_netdev(netdev); 7757 7758 if (pci_dev_run_wake(pdev)) 7759 pm_runtime_get_noresume(&pdev->dev); 7760 7761 /* Release control of h/w to f/w. If f/w is AMT enabled, this 7762 * would have already happened in close and is redundant. 7763 */ 7764 e1000e_release_hw_control(adapter); 7765 7766 e1000e_reset_interrupt_capability(adapter); 7767 kfree(adapter->tx_ring); 7768 kfree(adapter->rx_ring); 7769 7770 iounmap(adapter->hw.hw_addr); 7771 if ((adapter->hw.flash_address) && 7772 (adapter->hw.mac.type < e1000_pch_spt)) 7773 iounmap(adapter->hw.flash_address); 7774 pci_release_mem_regions(pdev); 7775 7776 free_netdev(netdev); 7777 7778 /* AER disable */ 7779 pci_disable_pcie_error_reporting(pdev); 7780 7781 pci_disable_device(pdev); 7782 } 7783 7784 /* PCI Error Recovery (ERS) */ 7785 static const struct pci_error_handlers e1000_err_handler = { 7786 .error_detected = e1000_io_error_detected, 7787 .slot_reset = e1000_io_slot_reset, 7788 .resume = e1000_io_resume, 7789 }; 7790 7791 static const struct pci_device_id e1000_pci_tbl[] = { 7792 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_COPPER), board_82571 }, 7793 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_FIBER), board_82571 }, 7794 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_QUAD_COPPER), board_82571 }, 7795 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_QUAD_COPPER_LP), 7796 board_82571 }, 7797 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_QUAD_FIBER), board_82571 }, 7798 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_SERDES), board_82571 }, 7799 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_SERDES_DUAL), board_82571 }, 7800 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_SERDES_QUAD), board_82571 }, 7801 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571PT_QUAD_COPPER), board_82571 }, 7802 7803 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI), board_82572 }, 7804 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI_COPPER), board_82572 }, 7805 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI_FIBER), board_82572 }, 7806 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI_SERDES), board_82572 }, 7807 7808 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82573E), board_82573 }, 7809 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82573E_IAMT), board_82573 }, 7810 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82573L), board_82573 }, 7811 7812 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82574L), board_82574 }, 7813 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82574LA), board_82574 }, 7814 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82583V), board_82583 }, 7815 7816 { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_COPPER_DPT), 7817 board_80003es2lan }, 7818 { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_COPPER_SPT), 7819 board_80003es2lan }, 7820 { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_SERDES_DPT), 7821 board_80003es2lan }, 7822 { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_SERDES_SPT), 7823 board_80003es2lan }, 7824 7825 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IFE), board_ich8lan }, 7826 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IFE_G), board_ich8lan }, 7827 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IFE_GT), board_ich8lan }, 7828 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_AMT), board_ich8lan }, 7829 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_C), board_ich8lan }, 7830 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_M), board_ich8lan }, 7831 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_M_AMT), board_ich8lan }, 7832 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_82567V_3), board_ich8lan }, 7833 7834 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IFE), board_ich9lan }, 7835 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IFE_G), board_ich9lan }, 7836 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IFE_GT), board_ich9lan }, 7837 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_AMT), board_ich9lan }, 7838 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_C), board_ich9lan }, 7839 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_BM), board_ich9lan }, 7840 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_M), board_ich9lan }, 7841 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_M_AMT), board_ich9lan }, 7842 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_M_V), board_ich9lan }, 7843 7844 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_LM), board_ich9lan }, 7845 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_LF), board_ich9lan }, 7846 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_V), board_ich9lan }, 7847 7848 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_D_BM_LM), board_ich10lan }, 7849 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_D_BM_LF), board_ich10lan }, 7850 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_D_BM_V), board_ich10lan }, 7851 7852 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_M_HV_LM), board_pchlan }, 7853 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_M_HV_LC), board_pchlan }, 7854 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_D_HV_DM), board_pchlan }, 7855 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_D_HV_DC), board_pchlan }, 7856 7857 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH2_LV_LM), board_pch2lan }, 7858 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH2_LV_V), board_pch2lan }, 7859 7860 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LPT_I217_LM), board_pch_lpt }, 7861 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LPT_I217_V), board_pch_lpt }, 7862 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LPTLP_I218_LM), board_pch_lpt }, 7863 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LPTLP_I218_V), board_pch_lpt }, 7864 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_I218_LM2), board_pch_lpt }, 7865 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_I218_V2), board_pch_lpt }, 7866 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_I218_LM3), board_pch_lpt }, 7867 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_I218_V3), board_pch_lpt }, 7868 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_LM), board_pch_spt }, 7869 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_V), board_pch_spt }, 7870 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_LM2), board_pch_spt }, 7871 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_V2), board_pch_spt }, 7872 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LBG_I219_LM3), board_pch_spt }, 7873 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_LM4), board_pch_spt }, 7874 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_V4), board_pch_spt }, 7875 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_LM5), board_pch_spt }, 7876 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_V5), board_pch_spt }, 7877 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CNP_I219_LM6), board_pch_cnp }, 7878 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CNP_I219_V6), board_pch_cnp }, 7879 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CNP_I219_LM7), board_pch_cnp }, 7880 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CNP_I219_V7), board_pch_cnp }, 7881 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ICP_I219_LM8), board_pch_cnp }, 7882 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ICP_I219_V8), board_pch_cnp }, 7883 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ICP_I219_LM9), board_pch_cnp }, 7884 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ICP_I219_V9), board_pch_cnp }, 7885 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CMP_I219_LM10), board_pch_cnp }, 7886 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CMP_I219_V10), board_pch_cnp }, 7887 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CMP_I219_LM11), board_pch_cnp }, 7888 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CMP_I219_V11), board_pch_cnp }, 7889 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CMP_I219_LM12), board_pch_spt }, 7890 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CMP_I219_V12), board_pch_spt }, 7891 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_TGP_I219_LM13), board_pch_tgp }, 7892 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_TGP_I219_V13), board_pch_tgp }, 7893 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_TGP_I219_LM14), board_pch_tgp }, 7894 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_TGP_I219_V14), board_pch_tgp }, 7895 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_TGP_I219_LM15), board_pch_tgp }, 7896 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_TGP_I219_V15), board_pch_tgp }, 7897 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_RPL_I219_LM23), board_pch_adp }, 7898 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_RPL_I219_V23), board_pch_adp }, 7899 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ADP_I219_LM16), board_pch_adp }, 7900 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ADP_I219_V16), board_pch_adp }, 7901 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ADP_I219_LM17), board_pch_adp }, 7902 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ADP_I219_V17), board_pch_adp }, 7903 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_RPL_I219_LM22), board_pch_adp }, 7904 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_RPL_I219_V22), board_pch_adp }, 7905 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_MTP_I219_LM18), board_pch_mtp }, 7906 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_MTP_I219_V18), board_pch_mtp }, 7907 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_MTP_I219_LM19), board_pch_mtp }, 7908 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_MTP_I219_V19), board_pch_mtp }, 7909 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LNP_I219_LM20), board_pch_mtp }, 7910 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LNP_I219_V20), board_pch_mtp }, 7911 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LNP_I219_LM21), board_pch_mtp }, 7912 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LNP_I219_V21), board_pch_mtp }, 7913 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ARL_I219_LM24), board_pch_mtp }, 7914 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ARL_I219_V24), board_pch_mtp }, 7915 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_PTP_I219_LM25), board_pch_mtp }, 7916 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_PTP_I219_V25), board_pch_mtp }, 7917 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_PTP_I219_LM26), board_pch_mtp }, 7918 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_PTP_I219_V26), board_pch_mtp }, 7919 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_PTP_I219_LM27), board_pch_mtp }, 7920 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_PTP_I219_V27), board_pch_mtp }, 7921 7922 { 0, 0, 0, 0, 0, 0, 0 } /* terminate list */ 7923 }; 7924 MODULE_DEVICE_TABLE(pci, e1000_pci_tbl); 7925 7926 static const struct dev_pm_ops e1000_pm_ops = { 7927 #ifdef CONFIG_PM_SLEEP 7928 .prepare = e1000e_pm_prepare, 7929 .suspend = e1000e_pm_suspend, 7930 .resume = e1000e_pm_resume, 7931 .freeze = e1000e_pm_freeze, 7932 .thaw = e1000e_pm_thaw, 7933 .poweroff = e1000e_pm_suspend, 7934 .restore = e1000e_pm_resume, 7935 #endif 7936 SET_RUNTIME_PM_OPS(e1000e_pm_runtime_suspend, e1000e_pm_runtime_resume, 7937 e1000e_pm_runtime_idle) 7938 }; 7939 7940 /* PCI Device API Driver */ 7941 static struct pci_driver e1000_driver = { 7942 .name = e1000e_driver_name, 7943 .id_table = e1000_pci_tbl, 7944 .probe = e1000_probe, 7945 .remove = e1000_remove, 7946 .driver = { 7947 .pm = &e1000_pm_ops, 7948 }, 7949 .shutdown = e1000_shutdown, 7950 .err_handler = &e1000_err_handler 7951 }; 7952 7953 /** 7954 * e1000_init_module - Driver Registration Routine 7955 * 7956 * e1000_init_module is the first routine called when the driver is 7957 * loaded. All it does is register with the PCI subsystem. 7958 **/ 7959 static int __init e1000_init_module(void) 7960 { 7961 pr_info("Intel(R) PRO/1000 Network Driver\n"); 7962 pr_info("Copyright(c) 1999 - 2015 Intel Corporation.\n"); 7963 7964 return pci_register_driver(&e1000_driver); 7965 } 7966 module_init(e1000_init_module); 7967 7968 /** 7969 * e1000_exit_module - Driver Exit Cleanup Routine 7970 * 7971 * e1000_exit_module is called just before the driver is removed 7972 * from memory. 7973 **/ 7974 static void __exit e1000_exit_module(void) 7975 { 7976 pci_unregister_driver(&e1000_driver); 7977 } 7978 module_exit(e1000_exit_module); 7979 7980 MODULE_AUTHOR("Intel Corporation, <linux.nics@intel.com>"); 7981 MODULE_DESCRIPTION("Intel(R) PRO/1000 Network Driver"); 7982 MODULE_LICENSE("GPL v2"); 7983 7984 /* netdev.c */ 7985