1 // SPDX-License-Identifier: GPL-2.0 2 /* Copyright(c) 1999 - 2006 Intel Corporation. */ 3 4 #include "e1000.h" 5 6 /* This is the only thing that needs to be changed to adjust the 7 * maximum number of ports that the driver can manage. 8 */ 9 10 #define E1000_MAX_NIC 32 11 12 #define OPTION_UNSET -1 13 #define OPTION_DISABLED 0 14 #define OPTION_ENABLED 1 15 16 /* All parameters are treated the same, as an integer array of values. 17 * This macro just reduces the need to repeat the same declaration code 18 * over and over (plus this helps to avoid typo bugs). 19 */ 20 21 #define E1000_PARAM_INIT { [0 ... E1000_MAX_NIC] = OPTION_UNSET } 22 #define E1000_PARAM(X, desc) \ 23 static int X[E1000_MAX_NIC+1] = E1000_PARAM_INIT; \ 24 static unsigned int num_##X; \ 25 module_param_array_named(X, X, int, &num_##X, 0); \ 26 MODULE_PARM_DESC(X, desc); 27 28 /* Transmit Descriptor Count 29 * 30 * Valid Range: 80-256 for 82542 and 82543 gigabit ethernet controllers 31 * Valid Range: 80-4096 for 82544 and newer 32 * 33 * Default Value: 256 34 */ 35 E1000_PARAM(TxDescriptors, "Number of transmit descriptors"); 36 37 /* Receive Descriptor Count 38 * 39 * Valid Range: 80-256 for 82542 and 82543 gigabit ethernet controllers 40 * Valid Range: 80-4096 for 82544 and newer 41 * 42 * Default Value: 256 43 */ 44 E1000_PARAM(RxDescriptors, "Number of receive descriptors"); 45 46 /* User Specified Speed Override 47 * 48 * Valid Range: 0, 10, 100, 1000 49 * - 0 - auto-negotiate at all supported speeds 50 * - 10 - only link at 10 Mbps 51 * - 100 - only link at 100 Mbps 52 * - 1000 - only link at 1000 Mbps 53 * 54 * Default Value: 0 55 */ 56 E1000_PARAM(Speed, "Speed setting"); 57 58 /* User Specified Duplex Override 59 * 60 * Valid Range: 0-2 61 * - 0 - auto-negotiate for duplex 62 * - 1 - only link at half duplex 63 * - 2 - only link at full duplex 64 * 65 * Default Value: 0 66 */ 67 E1000_PARAM(Duplex, "Duplex setting"); 68 69 /* Auto-negotiation Advertisement Override 70 * 71 * Valid Range: 0x01-0x0F, 0x20-0x2F (copper); 0x20 (fiber) 72 * 73 * The AutoNeg value is a bit mask describing which speed and duplex 74 * combinations should be advertised during auto-negotiation. 75 * The supported speed and duplex modes are listed below 76 * 77 * Bit 7 6 5 4 3 2 1 0 78 * Speed (Mbps) N/A N/A 1000 N/A 100 100 10 10 79 * Duplex Full Full Half Full Half 80 * 81 * Default Value: 0x2F (copper); 0x20 (fiber) 82 */ 83 E1000_PARAM(AutoNeg, "Advertised auto-negotiation setting"); 84 #define AUTONEG_ADV_DEFAULT 0x2F 85 86 /* User Specified Flow Control Override 87 * 88 * Valid Range: 0-3 89 * - 0 - No Flow Control 90 * - 1 - Rx only, respond to PAUSE frames but do not generate them 91 * - 2 - Tx only, generate PAUSE frames but ignore them on receive 92 * - 3 - Full Flow Control Support 93 * 94 * Default Value: Read flow control settings from the EEPROM 95 */ 96 E1000_PARAM(FlowControl, "Flow Control setting"); 97 98 /* XsumRX - Receive Checksum Offload Enable/Disable 99 * 100 * Valid Range: 0, 1 101 * - 0 - disables all checksum offload 102 * - 1 - enables receive IP/TCP/UDP checksum offload 103 * on 82543 and newer -based NICs 104 * 105 * Default Value: 1 106 */ 107 E1000_PARAM(XsumRX, "Disable or enable Receive Checksum offload"); 108 109 /* Transmit Interrupt Delay in units of 1.024 microseconds 110 * Tx interrupt delay needs to typically be set to something non zero 111 * 112 * Valid Range: 0-65535 113 */ 114 E1000_PARAM(TxIntDelay, "Transmit Interrupt Delay"); 115 #define DEFAULT_TIDV 8 116 #define MAX_TXDELAY 0xFFFF 117 #define MIN_TXDELAY 0 118 119 /* Transmit Absolute Interrupt Delay in units of 1.024 microseconds 120 * 121 * Valid Range: 0-65535 122 */ 123 E1000_PARAM(TxAbsIntDelay, "Transmit Absolute Interrupt Delay"); 124 #define DEFAULT_TADV 32 125 #define MAX_TXABSDELAY 0xFFFF 126 #define MIN_TXABSDELAY 0 127 128 /* Receive Interrupt Delay in units of 1.024 microseconds 129 * hardware will likely hang if you set this to anything but zero. 130 * 131 * Valid Range: 0-65535 132 */ 133 E1000_PARAM(RxIntDelay, "Receive Interrupt Delay"); 134 #define DEFAULT_RDTR 0 135 #define MAX_RXDELAY 0xFFFF 136 #define MIN_RXDELAY 0 137 138 /* Receive Absolute Interrupt Delay in units of 1.024 microseconds 139 * 140 * Valid Range: 0-65535 141 */ 142 E1000_PARAM(RxAbsIntDelay, "Receive Absolute Interrupt Delay"); 143 #define DEFAULT_RADV 8 144 #define MAX_RXABSDELAY 0xFFFF 145 #define MIN_RXABSDELAY 0 146 147 /* Interrupt Throttle Rate (interrupts/sec) 148 * 149 * Valid Range: 100-100000 (0=off, 1=dynamic, 3=dynamic conservative) 150 */ 151 E1000_PARAM(InterruptThrottleRate, "Interrupt Throttling Rate"); 152 #define DEFAULT_ITR 3 153 #define MAX_ITR 100000 154 #define MIN_ITR 100 155 156 /* Enable Smart Power Down of the PHY 157 * 158 * Valid Range: 0, 1 159 * 160 * Default Value: 0 (disabled) 161 */ 162 E1000_PARAM(SmartPowerDownEnable, "Enable PHY smart power down"); 163 164 struct e1000_option { 165 enum { enable_option, range_option, list_option } type; 166 const char *name; 167 const char *err; 168 int def; 169 union { 170 struct { /* range_option info */ 171 int min; 172 int max; 173 } r; 174 struct { /* list_option info */ 175 int nr; 176 const struct e1000_opt_list { int i; char *str; } *p; 177 } l; 178 } arg; 179 }; 180 181 static int e1000_validate_option(unsigned int *value, 182 const struct e1000_option *opt, 183 struct e1000_adapter *adapter) 184 { 185 if (*value == OPTION_UNSET) { 186 *value = opt->def; 187 return 0; 188 } 189 190 switch (opt->type) { 191 case enable_option: 192 switch (*value) { 193 case OPTION_ENABLED: 194 e_dev_info("%s Enabled\n", opt->name); 195 return 0; 196 case OPTION_DISABLED: 197 e_dev_info("%s Disabled\n", opt->name); 198 return 0; 199 } 200 break; 201 case range_option: 202 if (*value >= opt->arg.r.min && *value <= opt->arg.r.max) { 203 e_dev_info("%s set to %i\n", opt->name, *value); 204 return 0; 205 } 206 break; 207 case list_option: { 208 int i; 209 const struct e1000_opt_list *ent; 210 211 for (i = 0; i < opt->arg.l.nr; i++) { 212 ent = &opt->arg.l.p[i]; 213 if (*value == ent->i) { 214 if (ent->str[0] != '\0') 215 e_dev_info("%s\n", ent->str); 216 return 0; 217 } 218 } 219 } 220 break; 221 default: 222 BUG(); 223 } 224 225 e_dev_info("Invalid %s value specified (%i) %s\n", 226 opt->name, *value, opt->err); 227 *value = opt->def; 228 return -1; 229 } 230 231 static void e1000_check_fiber_options(struct e1000_adapter *adapter); 232 static void e1000_check_copper_options(struct e1000_adapter *adapter); 233 234 /** 235 * e1000_check_options - Range Checking for Command Line Parameters 236 * @adapter: board private structure 237 * 238 * This routine checks all command line parameters for valid user 239 * input. If an invalid value is given, or if no user specified 240 * value exists, a default value is used. The final value is stored 241 * in a variable in the adapter structure. 242 **/ 243 void e1000_check_options(struct e1000_adapter *adapter) 244 { 245 struct e1000_option opt; 246 int bd = adapter->bd_number; 247 248 if (bd >= E1000_MAX_NIC) { 249 e_dev_warn("Warning: no configuration for board #%i " 250 "using defaults for all values\n", bd); 251 } 252 253 { /* Transmit Descriptor Count */ 254 struct e1000_tx_ring *tx_ring = adapter->tx_ring; 255 int i; 256 e1000_mac_type mac_type = adapter->hw.mac_type; 257 258 opt = (struct e1000_option) { 259 .type = range_option, 260 .name = "Transmit Descriptors", 261 .err = "using default of " 262 __MODULE_STRING(E1000_DEFAULT_TXD), 263 .def = E1000_DEFAULT_TXD, 264 .arg = { .r = { 265 .min = E1000_MIN_TXD, 266 .max = mac_type < e1000_82544 ? E1000_MAX_TXD : E1000_MAX_82544_TXD 267 }} 268 }; 269 270 if (num_TxDescriptors > bd) { 271 tx_ring->count = TxDescriptors[bd]; 272 e1000_validate_option(&tx_ring->count, &opt, adapter); 273 tx_ring->count = ALIGN(tx_ring->count, 274 REQ_TX_DESCRIPTOR_MULTIPLE); 275 } else { 276 tx_ring->count = opt.def; 277 } 278 for (i = 0; i < adapter->num_tx_queues; i++) 279 tx_ring[i].count = tx_ring->count; 280 } 281 { /* Receive Descriptor Count */ 282 struct e1000_rx_ring *rx_ring = adapter->rx_ring; 283 int i; 284 e1000_mac_type mac_type = adapter->hw.mac_type; 285 286 opt = (struct e1000_option) { 287 .type = range_option, 288 .name = "Receive Descriptors", 289 .err = "using default of " 290 __MODULE_STRING(E1000_DEFAULT_RXD), 291 .def = E1000_DEFAULT_RXD, 292 .arg = { .r = { 293 .min = E1000_MIN_RXD, 294 .max = mac_type < e1000_82544 ? E1000_MAX_RXD : 295 E1000_MAX_82544_RXD 296 }} 297 }; 298 299 if (num_RxDescriptors > bd) { 300 rx_ring->count = RxDescriptors[bd]; 301 e1000_validate_option(&rx_ring->count, &opt, adapter); 302 rx_ring->count = ALIGN(rx_ring->count, 303 REQ_RX_DESCRIPTOR_MULTIPLE); 304 } else { 305 rx_ring->count = opt.def; 306 } 307 for (i = 0; i < adapter->num_rx_queues; i++) 308 rx_ring[i].count = rx_ring->count; 309 } 310 { /* Checksum Offload Enable/Disable */ 311 opt = (struct e1000_option) { 312 .type = enable_option, 313 .name = "Checksum Offload", 314 .err = "defaulting to Enabled", 315 .def = OPTION_ENABLED 316 }; 317 318 if (num_XsumRX > bd) { 319 unsigned int rx_csum = XsumRX[bd]; 320 e1000_validate_option(&rx_csum, &opt, adapter); 321 adapter->rx_csum = rx_csum; 322 } else { 323 adapter->rx_csum = opt.def; 324 } 325 } 326 { /* Flow Control */ 327 328 static const struct e1000_opt_list fc_list[] = { 329 { E1000_FC_NONE, "Flow Control Disabled" }, 330 { E1000_FC_RX_PAUSE, "Flow Control Receive Only" }, 331 { E1000_FC_TX_PAUSE, "Flow Control Transmit Only" }, 332 { E1000_FC_FULL, "Flow Control Enabled" }, 333 { E1000_FC_DEFAULT, "Flow Control Hardware Default" } 334 }; 335 336 opt = (struct e1000_option) { 337 .type = list_option, 338 .name = "Flow Control", 339 .err = "reading default settings from EEPROM", 340 .def = E1000_FC_DEFAULT, 341 .arg = { .l = { .nr = ARRAY_SIZE(fc_list), 342 .p = fc_list }} 343 }; 344 345 if (num_FlowControl > bd) { 346 unsigned int fc = FlowControl[bd]; 347 e1000_validate_option(&fc, &opt, adapter); 348 adapter->hw.fc = adapter->hw.original_fc = fc; 349 } else { 350 adapter->hw.fc = adapter->hw.original_fc = opt.def; 351 } 352 } 353 { /* Transmit Interrupt Delay */ 354 opt = (struct e1000_option) { 355 .type = range_option, 356 .name = "Transmit Interrupt Delay", 357 .err = "using default of " __MODULE_STRING(DEFAULT_TIDV), 358 .def = DEFAULT_TIDV, 359 .arg = { .r = { .min = MIN_TXDELAY, 360 .max = MAX_TXDELAY }} 361 }; 362 363 if (num_TxIntDelay > bd) { 364 adapter->tx_int_delay = TxIntDelay[bd]; 365 e1000_validate_option(&adapter->tx_int_delay, &opt, 366 adapter); 367 } else { 368 adapter->tx_int_delay = opt.def; 369 } 370 } 371 { /* Transmit Absolute Interrupt Delay */ 372 opt = (struct e1000_option) { 373 .type = range_option, 374 .name = "Transmit Absolute Interrupt Delay", 375 .err = "using default of " __MODULE_STRING(DEFAULT_TADV), 376 .def = DEFAULT_TADV, 377 .arg = { .r = { .min = MIN_TXABSDELAY, 378 .max = MAX_TXABSDELAY }} 379 }; 380 381 if (num_TxAbsIntDelay > bd) { 382 adapter->tx_abs_int_delay = TxAbsIntDelay[bd]; 383 e1000_validate_option(&adapter->tx_abs_int_delay, &opt, 384 adapter); 385 } else { 386 adapter->tx_abs_int_delay = opt.def; 387 } 388 } 389 { /* Receive Interrupt Delay */ 390 opt = (struct e1000_option) { 391 .type = range_option, 392 .name = "Receive Interrupt Delay", 393 .err = "using default of " __MODULE_STRING(DEFAULT_RDTR), 394 .def = DEFAULT_RDTR, 395 .arg = { .r = { .min = MIN_RXDELAY, 396 .max = MAX_RXDELAY }} 397 }; 398 399 if (num_RxIntDelay > bd) { 400 adapter->rx_int_delay = RxIntDelay[bd]; 401 e1000_validate_option(&adapter->rx_int_delay, &opt, 402 adapter); 403 } else { 404 adapter->rx_int_delay = opt.def; 405 } 406 } 407 { /* Receive Absolute Interrupt Delay */ 408 opt = (struct e1000_option) { 409 .type = range_option, 410 .name = "Receive Absolute Interrupt Delay", 411 .err = "using default of " __MODULE_STRING(DEFAULT_RADV), 412 .def = DEFAULT_RADV, 413 .arg = { .r = { .min = MIN_RXABSDELAY, 414 .max = MAX_RXABSDELAY }} 415 }; 416 417 if (num_RxAbsIntDelay > bd) { 418 adapter->rx_abs_int_delay = RxAbsIntDelay[bd]; 419 e1000_validate_option(&adapter->rx_abs_int_delay, &opt, 420 adapter); 421 } else { 422 adapter->rx_abs_int_delay = opt.def; 423 } 424 } 425 { /* Interrupt Throttling Rate */ 426 opt = (struct e1000_option) { 427 .type = range_option, 428 .name = "Interrupt Throttling Rate (ints/sec)", 429 .err = "using default of " __MODULE_STRING(DEFAULT_ITR), 430 .def = DEFAULT_ITR, 431 .arg = { .r = { .min = MIN_ITR, 432 .max = MAX_ITR }} 433 }; 434 435 if (num_InterruptThrottleRate > bd) { 436 adapter->itr = InterruptThrottleRate[bd]; 437 switch (adapter->itr) { 438 case 0: 439 e_dev_info("%s turned off\n", opt.name); 440 break; 441 case 1: 442 e_dev_info("%s set to dynamic mode\n", 443 opt.name); 444 adapter->itr_setting = adapter->itr; 445 adapter->itr = 20000; 446 break; 447 case 3: 448 e_dev_info("%s set to dynamic conservative " 449 "mode\n", opt.name); 450 adapter->itr_setting = adapter->itr; 451 adapter->itr = 20000; 452 break; 453 case 4: 454 e_dev_info("%s set to simplified " 455 "(2000-8000) ints mode\n", opt.name); 456 adapter->itr_setting = adapter->itr; 457 break; 458 default: 459 e1000_validate_option(&adapter->itr, &opt, 460 adapter); 461 /* save the setting, because the dynamic bits 462 * change itr. 463 * clear the lower two bits because they are 464 * used as control 465 */ 466 adapter->itr_setting = adapter->itr & ~3; 467 break; 468 } 469 } else { 470 adapter->itr_setting = opt.def; 471 adapter->itr = 20000; 472 } 473 } 474 { /* Smart Power Down */ 475 opt = (struct e1000_option) { 476 .type = enable_option, 477 .name = "PHY Smart Power Down", 478 .err = "defaulting to Disabled", 479 .def = OPTION_DISABLED 480 }; 481 482 if (num_SmartPowerDownEnable > bd) { 483 unsigned int spd = SmartPowerDownEnable[bd]; 484 e1000_validate_option(&spd, &opt, adapter); 485 adapter->smart_power_down = spd; 486 } else { 487 adapter->smart_power_down = opt.def; 488 } 489 } 490 491 switch (adapter->hw.media_type) { 492 case e1000_media_type_fiber: 493 case e1000_media_type_internal_serdes: 494 e1000_check_fiber_options(adapter); 495 break; 496 case e1000_media_type_copper: 497 e1000_check_copper_options(adapter); 498 break; 499 default: 500 BUG(); 501 } 502 } 503 504 /** 505 * e1000_check_fiber_options - Range Checking for Link Options, Fiber Version 506 * @adapter: board private structure 507 * 508 * Handles speed and duplex options on fiber adapters 509 **/ 510 static void e1000_check_fiber_options(struct e1000_adapter *adapter) 511 { 512 int bd = adapter->bd_number; 513 if (num_Speed > bd) { 514 e_dev_info("Speed not valid for fiber adapters, parameter " 515 "ignored\n"); 516 } 517 518 if (num_Duplex > bd) { 519 e_dev_info("Duplex not valid for fiber adapters, parameter " 520 "ignored\n"); 521 } 522 523 if ((num_AutoNeg > bd) && (AutoNeg[bd] != 0x20)) { 524 e_dev_info("AutoNeg other than 1000/Full is not valid for fiber" 525 "adapters, parameter ignored\n"); 526 } 527 } 528 529 /** 530 * e1000_check_copper_options - Range Checking for Link Options, Copper Version 531 * @adapter: board private structure 532 * 533 * Handles speed and duplex options on copper adapters 534 **/ 535 static void e1000_check_copper_options(struct e1000_adapter *adapter) 536 { 537 struct e1000_option opt; 538 unsigned int speed, dplx, an; 539 int bd = adapter->bd_number; 540 541 { /* Speed */ 542 static const struct e1000_opt_list speed_list[] = { 543 { 0, "" }, 544 { SPEED_10, "" }, 545 { SPEED_100, "" }, 546 { SPEED_1000, "" }}; 547 548 opt = (struct e1000_option) { 549 .type = list_option, 550 .name = "Speed", 551 .err = "parameter ignored", 552 .def = 0, 553 .arg = { .l = { .nr = ARRAY_SIZE(speed_list), 554 .p = speed_list }} 555 }; 556 557 if (num_Speed > bd) { 558 speed = Speed[bd]; 559 e1000_validate_option(&speed, &opt, adapter); 560 } else { 561 speed = opt.def; 562 } 563 } 564 { /* Duplex */ 565 static const struct e1000_opt_list dplx_list[] = { 566 { 0, "" }, 567 { HALF_DUPLEX, "" }, 568 { FULL_DUPLEX, "" }}; 569 570 opt = (struct e1000_option) { 571 .type = list_option, 572 .name = "Duplex", 573 .err = "parameter ignored", 574 .def = 0, 575 .arg = { .l = { .nr = ARRAY_SIZE(dplx_list), 576 .p = dplx_list }} 577 }; 578 579 if (num_Duplex > bd) { 580 dplx = Duplex[bd]; 581 e1000_validate_option(&dplx, &opt, adapter); 582 } else { 583 dplx = opt.def; 584 } 585 } 586 587 if ((num_AutoNeg > bd) && (speed != 0 || dplx != 0)) { 588 e_dev_info("AutoNeg specified along with Speed or Duplex, " 589 "parameter ignored\n"); 590 adapter->hw.autoneg_advertised = AUTONEG_ADV_DEFAULT; 591 } else { /* Autoneg */ 592 static const struct e1000_opt_list an_list[] = 593 #define AA "AutoNeg advertising " 594 {{ 0x01, AA "10/HD" }, 595 { 0x02, AA "10/FD" }, 596 { 0x03, AA "10/FD, 10/HD" }, 597 { 0x04, AA "100/HD" }, 598 { 0x05, AA "100/HD, 10/HD" }, 599 { 0x06, AA "100/HD, 10/FD" }, 600 { 0x07, AA "100/HD, 10/FD, 10/HD" }, 601 { 0x08, AA "100/FD" }, 602 { 0x09, AA "100/FD, 10/HD" }, 603 { 0x0a, AA "100/FD, 10/FD" }, 604 { 0x0b, AA "100/FD, 10/FD, 10/HD" }, 605 { 0x0c, AA "100/FD, 100/HD" }, 606 { 0x0d, AA "100/FD, 100/HD, 10/HD" }, 607 { 0x0e, AA "100/FD, 100/HD, 10/FD" }, 608 { 0x0f, AA "100/FD, 100/HD, 10/FD, 10/HD" }, 609 { 0x20, AA "1000/FD" }, 610 { 0x21, AA "1000/FD, 10/HD" }, 611 { 0x22, AA "1000/FD, 10/FD" }, 612 { 0x23, AA "1000/FD, 10/FD, 10/HD" }, 613 { 0x24, AA "1000/FD, 100/HD" }, 614 { 0x25, AA "1000/FD, 100/HD, 10/HD" }, 615 { 0x26, AA "1000/FD, 100/HD, 10/FD" }, 616 { 0x27, AA "1000/FD, 100/HD, 10/FD, 10/HD" }, 617 { 0x28, AA "1000/FD, 100/FD" }, 618 { 0x29, AA "1000/FD, 100/FD, 10/HD" }, 619 { 0x2a, AA "1000/FD, 100/FD, 10/FD" }, 620 { 0x2b, AA "1000/FD, 100/FD, 10/FD, 10/HD" }, 621 { 0x2c, AA "1000/FD, 100/FD, 100/HD" }, 622 { 0x2d, AA "1000/FD, 100/FD, 100/HD, 10/HD" }, 623 { 0x2e, AA "1000/FD, 100/FD, 100/HD, 10/FD" }, 624 { 0x2f, AA "1000/FD, 100/FD, 100/HD, 10/FD, 10/HD" }}; 625 626 opt = (struct e1000_option) { 627 .type = list_option, 628 .name = "AutoNeg", 629 .err = "parameter ignored", 630 .def = AUTONEG_ADV_DEFAULT, 631 .arg = { .l = { .nr = ARRAY_SIZE(an_list), 632 .p = an_list }} 633 }; 634 635 if (num_AutoNeg > bd) { 636 an = AutoNeg[bd]; 637 e1000_validate_option(&an, &opt, adapter); 638 } else { 639 an = opt.def; 640 } 641 adapter->hw.autoneg_advertised = an; 642 } 643 644 switch (speed + dplx) { 645 case 0: 646 adapter->hw.autoneg = adapter->fc_autoneg = 1; 647 if ((num_Speed > bd) && (speed != 0 || dplx != 0)) 648 e_dev_info("Speed and duplex autonegotiation " 649 "enabled\n"); 650 break; 651 case HALF_DUPLEX: 652 e_dev_info("Half Duplex specified without Speed\n"); 653 e_dev_info("Using Autonegotiation at Half Duplex only\n"); 654 adapter->hw.autoneg = adapter->fc_autoneg = 1; 655 adapter->hw.autoneg_advertised = ADVERTISE_10_HALF | 656 ADVERTISE_100_HALF; 657 break; 658 case FULL_DUPLEX: 659 e_dev_info("Full Duplex specified without Speed\n"); 660 e_dev_info("Using Autonegotiation at Full Duplex only\n"); 661 adapter->hw.autoneg = adapter->fc_autoneg = 1; 662 adapter->hw.autoneg_advertised = ADVERTISE_10_FULL | 663 ADVERTISE_100_FULL | 664 ADVERTISE_1000_FULL; 665 break; 666 case SPEED_10: 667 e_dev_info("10 Mbps Speed specified without Duplex\n"); 668 e_dev_info("Using Autonegotiation at 10 Mbps only\n"); 669 adapter->hw.autoneg = adapter->fc_autoneg = 1; 670 adapter->hw.autoneg_advertised = ADVERTISE_10_HALF | 671 ADVERTISE_10_FULL; 672 break; 673 case SPEED_10 + HALF_DUPLEX: 674 e_dev_info("Forcing to 10 Mbps Half Duplex\n"); 675 adapter->hw.autoneg = adapter->fc_autoneg = 0; 676 adapter->hw.forced_speed_duplex = e1000_10_half; 677 adapter->hw.autoneg_advertised = 0; 678 break; 679 case SPEED_10 + FULL_DUPLEX: 680 e_dev_info("Forcing to 10 Mbps Full Duplex\n"); 681 adapter->hw.autoneg = adapter->fc_autoneg = 0; 682 adapter->hw.forced_speed_duplex = e1000_10_full; 683 adapter->hw.autoneg_advertised = 0; 684 break; 685 case SPEED_100: 686 e_dev_info("100 Mbps Speed specified without Duplex\n"); 687 e_dev_info("Using Autonegotiation at 100 Mbps only\n"); 688 adapter->hw.autoneg = adapter->fc_autoneg = 1; 689 adapter->hw.autoneg_advertised = ADVERTISE_100_HALF | 690 ADVERTISE_100_FULL; 691 break; 692 case SPEED_100 + HALF_DUPLEX: 693 e_dev_info("Forcing to 100 Mbps Half Duplex\n"); 694 adapter->hw.autoneg = adapter->fc_autoneg = 0; 695 adapter->hw.forced_speed_duplex = e1000_100_half; 696 adapter->hw.autoneg_advertised = 0; 697 break; 698 case SPEED_100 + FULL_DUPLEX: 699 e_dev_info("Forcing to 100 Mbps Full Duplex\n"); 700 adapter->hw.autoneg = adapter->fc_autoneg = 0; 701 adapter->hw.forced_speed_duplex = e1000_100_full; 702 adapter->hw.autoneg_advertised = 0; 703 break; 704 case SPEED_1000: 705 e_dev_info("1000 Mbps Speed specified without Duplex\n"); 706 goto full_duplex_only; 707 case SPEED_1000 + HALF_DUPLEX: 708 e_dev_info("Half Duplex is not supported at 1000 Mbps\n"); 709 fallthrough; 710 case SPEED_1000 + FULL_DUPLEX: 711 full_duplex_only: 712 e_dev_info("Using Autonegotiation at 1000 Mbps Full Duplex " 713 "only\n"); 714 adapter->hw.autoneg = adapter->fc_autoneg = 1; 715 adapter->hw.autoneg_advertised = ADVERTISE_1000_FULL; 716 break; 717 default: 718 BUG(); 719 } 720 721 /* Speed, AutoNeg and MDI/MDI-X must all play nice */ 722 if (e1000_validate_mdi_setting(&(adapter->hw)) < 0) { 723 e_dev_info("Speed, AutoNeg and MDI-X specs are incompatible. " 724 "Setting MDI-X to a compatible value.\n"); 725 } 726 } 727 728