1# 2# Freescale device configuration 3# 4 5config NET_VENDOR_FREESCALE 6 bool "Freescale devices" 7 default y 8 depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \ 9 M523x || M527x || M5272 || M528x || M520x || M532x || \ 10 ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM) || \ 11 ARCH_LAYERSCAPE || COMPILE_TEST 12 ---help--- 13 If you have a network (Ethernet) card belonging to this class, say Y. 14 15 Note that the answer to this question doesn't directly affect the 16 kernel: saying N will just cause the configurator to skip all 17 the questions about Freescale devices. If you say Y, you will be 18 asked for your specific card in the following questions. 19 20if NET_VENDOR_FREESCALE 21 22config FEC 23 tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)" 24 depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \ 25 ARCH_MXC || SOC_IMX28) 26 default ARCH_MXC || SOC_IMX28 if ARM 27 select PHYLIB 28 imply PTP_1588_CLOCK 29 ---help--- 30 Say Y here if you want to use the built-in 10/100 Fast ethernet 31 controller on some Motorola ColdFire and Freescale i.MX processors. 32 33config FEC_MPC52xx 34 tristate "FEC MPC52xx driver" 35 depends on PPC_MPC52xx && PPC_BESTCOMM 36 select CRC32 37 select PHYLIB 38 select PPC_BESTCOMM_FEC 39 ---help--- 40 This option enables support for the MPC5200's on-chip 41 Fast Ethernet Controller 42 If compiled as module, it will be called fec_mpc52xx. 43 44config FEC_MPC52xx_MDIO 45 bool "FEC MPC52xx MDIO bus driver" 46 depends on FEC_MPC52xx 47 default y 48 ---help--- 49 The MPC5200's FEC can connect to the Ethernet either with 50 an external MII PHY chip or 10 Mbps 7-wire interface 51 (Motorola? industry standard). 52 If your board uses an external PHY connected to FEC, enable this. 53 If not sure, enable. 54 If compiled as module, it will be called fec_mpc52xx_phy. 55 56source "drivers/net/ethernet/freescale/fs_enet/Kconfig" 57source "drivers/net/ethernet/freescale/fman/Kconfig" 58 59config FSL_PQ_MDIO 60 tristate "Freescale PQ MDIO" 61 select PHYLIB 62 ---help--- 63 This driver supports the MDIO bus used by the gianfar and UCC drivers. 64 65config FSL_XGMAC_MDIO 66 tristate "Freescale XGMAC MDIO" 67 select PHYLIB 68 depends on OF 69 select OF_MDIO 70 ---help--- 71 This driver supports the MDIO bus on the Fman 10G Ethernet MACs, and 72 on the FMan mEMAC (which supports both Clauses 22 and 45) 73 74config UCC_GETH 75 tristate "Freescale QE Gigabit Ethernet" 76 depends on QUICC_ENGINE 77 select FSL_PQ_MDIO 78 select PHYLIB 79 ---help--- 80 This driver supports the Gigabit Ethernet mode of the QUICC Engine, 81 which is available on some Freescale SOCs. 82 83config UGETH_TX_ON_DEMAND 84 bool "Transmit on Demand support" 85 depends on UCC_GETH 86 87config GIANFAR 88 tristate "Gianfar Ethernet" 89 depends on HAS_DMA 90 select FSL_PQ_MDIO 91 select PHYLIB 92 select CRC32 93 ---help--- 94 This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx, 95 and MPC86xx family of chips, the eTSEC on LS1021A and the FEC 96 on the 8540. 97 98source "drivers/net/ethernet/freescale/dpaa/Kconfig" 99 100endif # NET_VENDOR_FREESCALE 101