1# 2# Freescale device configuration 3# 4 5config NET_VENDOR_FREESCALE 6 bool "Freescale devices" 7 default y 8 depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \ 9 M523x || M527x || M5272 || M528x || M520x || M532x || \ 10 ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM) 11 ---help--- 12 If you have a network (Ethernet) card belonging to this class, say Y 13 and read the Ethernet-HOWTO, available from 14 <http://www.tldp.org/docs.html#howto>. 15 16 Note that the answer to this question doesn't directly affect the 17 kernel: saying N will just cause the configurator to skip all 18 the questions about Freescale devices. If you say Y, you will be 19 asked for your specific card in the following questions. 20 21if NET_VENDOR_FREESCALE 22 23config FEC 24 tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)" 25 depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \ 26 ARCH_MXC || SOC_IMX28) 27 default ARCH_MXC || SOC_IMX28 if ARM 28 select PHYLIB 29 ---help--- 30 Say Y here if you want to use the built-in 10/100 Fast ethernet 31 controller on some Motorola ColdFire and Freescale i.MX processors. 32 33config FEC_MPC52xx 34 tristate "FEC MPC52xx driver" 35 depends on PPC_MPC52xx && PPC_BESTCOMM 36 select CRC32 37 select PHYLIB 38 select PPC_BESTCOMM_FEC 39 ---help--- 40 This option enables support for the MPC5200's on-chip 41 Fast Ethernet Controller 42 If compiled as module, it will be called fec_mpc52xx. 43 44config FEC_MPC52xx_MDIO 45 bool "FEC MPC52xx MDIO bus driver" 46 depends on FEC_MPC52xx 47 default y 48 ---help--- 49 The MPC5200's FEC can connect to the Ethernet either with 50 an external MII PHY chip or 10 Mbps 7-wire interface 51 (Motorola? industry standard). 52 If your board uses an external PHY connected to FEC, enable this. 53 If not sure, enable. 54 If compiled as module, it will be called fec_mpc52xx_phy. 55 56source "drivers/net/ethernet/freescale/fs_enet/Kconfig" 57 58config FSL_PQ_MDIO 59 tristate "Freescale PQ MDIO" 60 depends on FSL_SOC 61 select PHYLIB 62 ---help--- 63 This driver supports the MDIO bus used by the gianfar and UCC drivers. 64 65config FSL_XGMAC_MDIO 66 tristate "Freescale XGMAC MDIO" 67 depends on FSL_SOC 68 select PHYLIB 69 ---help--- 70 This driver supports the MDIO bus on the Fman 10G Ethernet MACs. 71 72config UCC_GETH 73 tristate "Freescale QE Gigabit Ethernet" 74 depends on QUICC_ENGINE 75 select FSL_PQ_MDIO 76 select PHYLIB 77 ---help--- 78 This driver supports the Gigabit Ethernet mode of the QUICC Engine, 79 which is available on some Freescale SOCs. 80 81config UGETH_TX_ON_DEMAND 82 bool "Transmit on Demand support" 83 depends on UCC_GETH 84 85config GIANFAR 86 tristate "Gianfar Ethernet" 87 depends on FSL_SOC 88 select FSL_PQ_MDIO 89 select PHYLIB 90 select CRC32 91 ---help--- 92 This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx, 93 and MPC86xx family of chips, and the FEC on the 8540. 94 95config FEC_PTP 96 bool "PTP Hardware Clock (PHC)" 97 depends on FEC && ARCH_MXC && !SOC_IMX25 && !SOC_IMX27 && !SOC_IMX35 && !SOC_IMX5 98 select PTP_1588_CLOCK 99 --help--- 100 Say Y here if you want to use PTP Hardware Clock (PHC) in the 101 driver. Only the basic clock operations have been implemented. 102 103endif # NET_VENDOR_FREESCALE 104