1# 2# Freescale device configuration 3# 4 5config NET_VENDOR_FREESCALE 6 bool "Freescale devices" 7 default y 8 depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \ 9 M523x || M527x || M5272 || M528x || M520x || M532x || \ 10 ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM) 11 ---help--- 12 If you have a network (Ethernet) card belonging to this class, say Y. 13 14 Note that the answer to this question doesn't directly affect the 15 kernel: saying N will just cause the configurator to skip all 16 the questions about Freescale devices. If you say Y, you will be 17 asked for your specific card in the following questions. 18 19if NET_VENDOR_FREESCALE 20 21config FEC 22 tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)" 23 depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \ 24 ARCH_MXC || SOC_IMX28) 25 default ARCH_MXC || SOC_IMX28 if ARM 26 select PHYLIB 27 select PTP_1588_CLOCK 28 ---help--- 29 Say Y here if you want to use the built-in 10/100 Fast ethernet 30 controller on some Motorola ColdFire and Freescale i.MX processors. 31 32config FEC_MPC52xx 33 tristate "FEC MPC52xx driver" 34 depends on PPC_MPC52xx && PPC_BESTCOMM 35 select CRC32 36 select PHYLIB 37 select PPC_BESTCOMM_FEC 38 ---help--- 39 This option enables support for the MPC5200's on-chip 40 Fast Ethernet Controller 41 If compiled as module, it will be called fec_mpc52xx. 42 43config FEC_MPC52xx_MDIO 44 bool "FEC MPC52xx MDIO bus driver" 45 depends on FEC_MPC52xx 46 default y 47 ---help--- 48 The MPC5200's FEC can connect to the Ethernet either with 49 an external MII PHY chip or 10 Mbps 7-wire interface 50 (Motorola? industry standard). 51 If your board uses an external PHY connected to FEC, enable this. 52 If not sure, enable. 53 If compiled as module, it will be called fec_mpc52xx_phy. 54 55source "drivers/net/ethernet/freescale/fs_enet/Kconfig" 56 57config FSL_PQ_MDIO 58 tristate "Freescale PQ MDIO" 59 select PHYLIB 60 ---help--- 61 This driver supports the MDIO bus used by the gianfar and UCC drivers. 62 63config FSL_XGMAC_MDIO 64 tristate "Freescale XGMAC MDIO" 65 select PHYLIB 66 select OF_MDIO 67 ---help--- 68 This driver supports the MDIO bus on the Fman 10G Ethernet MACs, and 69 on the FMan mEMAC (which supports both Clauses 22 and 45) 70 71config UCC_GETH 72 tristate "Freescale QE Gigabit Ethernet" 73 depends on QUICC_ENGINE 74 select FSL_PQ_MDIO 75 select PHYLIB 76 ---help--- 77 This driver supports the Gigabit Ethernet mode of the QUICC Engine, 78 which is available on some Freescale SOCs. 79 80config UGETH_TX_ON_DEMAND 81 bool "Transmit on Demand support" 82 depends on UCC_GETH 83 84config GIANFAR 85 tristate "Gianfar Ethernet" 86 select FSL_PQ_MDIO 87 select PHYLIB 88 select CRC32 89 ---help--- 90 This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx, 91 and MPC86xx family of chips, the eTSEC on LS1021A and the FEC 92 on the 8540. 93 94endif # NET_VENDOR_FREESCALE 95