1# SPDX-License-Identifier: GPL-2.0-only 2# 3# Freescale device configuration 4# 5 6config NET_VENDOR_FREESCALE 7 bool "Freescale devices" 8 default y 9 depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \ 10 M523x || M527x || M5272 || M528x || M520x || M532x || \ 11 ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM) || \ 12 ARCH_LAYERSCAPE || COMPILE_TEST 13 ---help--- 14 If you have a network (Ethernet) card belonging to this class, say Y. 15 16 Note that the answer to this question doesn't directly affect the 17 kernel: saying N will just cause the configurator to skip all 18 the questions about Freescale devices. If you say Y, you will be 19 asked for your specific card in the following questions. 20 21if NET_VENDOR_FREESCALE 22 23config FEC 24 tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)" 25 depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \ 26 ARCH_MXC || SOC_IMX28 || COMPILE_TEST) 27 default ARCH_MXC || SOC_IMX28 if ARM 28 select PHYLIB 29 imply PTP_1588_CLOCK 30 ---help--- 31 Say Y here if you want to use the built-in 10/100 Fast ethernet 32 controller on some Motorola ColdFire and Freescale i.MX processors. 33 34config FEC_MPC52xx 35 tristate "FEC MPC52xx driver" 36 depends on PPC_MPC52xx && PPC_BESTCOMM 37 select CRC32 38 select PHYLIB 39 select PPC_BESTCOMM_FEC 40 ---help--- 41 This option enables support for the MPC5200's on-chip 42 Fast Ethernet Controller 43 If compiled as module, it will be called fec_mpc52xx. 44 45config FEC_MPC52xx_MDIO 46 bool "FEC MPC52xx MDIO bus driver" 47 depends on FEC_MPC52xx 48 default y 49 ---help--- 50 The MPC5200's FEC can connect to the Ethernet either with 51 an external MII PHY chip or 10 Mbps 7-wire interface 52 (Motorola? industry standard). 53 If your board uses an external PHY connected to FEC, enable this. 54 If not sure, enable. 55 If compiled as module, it will be called fec_mpc52xx_phy. 56 57source "drivers/net/ethernet/freescale/fs_enet/Kconfig" 58source "drivers/net/ethernet/freescale/fman/Kconfig" 59 60config FSL_PQ_MDIO 61 tristate "Freescale PQ MDIO" 62 select PHYLIB 63 ---help--- 64 This driver supports the MDIO bus used by the gianfar and UCC drivers. 65 66config FSL_XGMAC_MDIO 67 tristate "Freescale XGMAC MDIO" 68 select PHYLIB 69 depends on OF 70 select OF_MDIO 71 ---help--- 72 This driver supports the MDIO bus on the Fman 10G Ethernet MACs, and 73 on the FMan mEMAC (which supports both Clauses 22 and 45) 74 75config UCC_GETH 76 tristate "Freescale QE Gigabit Ethernet" 77 depends on QUICC_ENGINE && PPC32 78 select FSL_PQ_MDIO 79 select PHYLIB 80 select FIXED_PHY 81 ---help--- 82 This driver supports the Gigabit Ethernet mode of the QUICC Engine, 83 which is available on some Freescale SOCs. 84 85config UGETH_TX_ON_DEMAND 86 bool "Transmit on Demand support" 87 depends on UCC_GETH 88 89config GIANFAR 90 tristate "Gianfar Ethernet" 91 depends on HAS_DMA 92 select FSL_PQ_MDIO 93 select PHYLIB 94 select FIXED_PHY 95 select CRC32 96 ---help--- 97 This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx, 98 and MPC86xx family of chips, the eTSEC on LS1021A and the FEC 99 on the 8540. 100 101source "drivers/net/ethernet/freescale/dpaa/Kconfig" 102source "drivers/net/ethernet/freescale/dpaa2/Kconfig" 103source "drivers/net/ethernet/freescale/enetc/Kconfig" 104 105endif # NET_VENDOR_FREESCALE 106