1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * Copyright (C) 2001,2002,2003,2004 Broadcom Corporation 4 * Copyright (c) 2006, 2007 Maciej W. Rozycki 5 * 6 * This driver is designed for the Broadcom SiByte SOC built-in 7 * Ethernet controllers. Written by Mitch Lichtenberg at Broadcom Corp. 8 * 9 * Updated to the driver model and the PHY abstraction layer 10 * by Maciej W. Rozycki. 11 */ 12 13 #include <linux/bug.h> 14 #include <linux/module.h> 15 #include <linux/kernel.h> 16 #include <linux/string.h> 17 #include <linux/timer.h> 18 #include <linux/errno.h> 19 #include <linux/ioport.h> 20 #include <linux/slab.h> 21 #include <linux/interrupt.h> 22 #include <linux/netdevice.h> 23 #include <linux/etherdevice.h> 24 #include <linux/skbuff.h> 25 #include <linux/bitops.h> 26 #include <linux/err.h> 27 #include <linux/ethtool.h> 28 #include <linux/mii.h> 29 #include <linux/phy.h> 30 #include <linux/platform_device.h> 31 #include <linux/prefetch.h> 32 33 #include <asm/cache.h> 34 #include <asm/io.h> 35 #include <asm/processor.h> /* Processor type for cache alignment. */ 36 37 /* Operational parameters that usually are not changed. */ 38 39 #define CONFIG_SBMAC_COALESCE 40 41 /* Time in jiffies before concluding the transmitter is hung. */ 42 #define TX_TIMEOUT (2*HZ) 43 44 45 MODULE_AUTHOR("Mitch Lichtenberg (Broadcom Corp.)"); 46 MODULE_DESCRIPTION("Broadcom SiByte SOC GB Ethernet driver"); 47 48 /* A few user-configurable values which may be modified when a driver 49 module is loaded. */ 50 51 /* 1 normal messages, 0 quiet .. 7 verbose. */ 52 static int debug = 1; 53 module_param(debug, int, 0444); 54 MODULE_PARM_DESC(debug, "Debug messages"); 55 56 #ifdef CONFIG_SBMAC_COALESCE 57 static int int_pktcnt_tx = 255; 58 module_param(int_pktcnt_tx, int, 0444); 59 MODULE_PARM_DESC(int_pktcnt_tx, "TX packet count"); 60 61 static int int_timeout_tx = 255; 62 module_param(int_timeout_tx, int, 0444); 63 MODULE_PARM_DESC(int_timeout_tx, "TX timeout value"); 64 65 static int int_pktcnt_rx = 64; 66 module_param(int_pktcnt_rx, int, 0444); 67 MODULE_PARM_DESC(int_pktcnt_rx, "RX packet count"); 68 69 static int int_timeout_rx = 64; 70 module_param(int_timeout_rx, int, 0444); 71 MODULE_PARM_DESC(int_timeout_rx, "RX timeout value"); 72 #endif 73 74 #include <asm/sibyte/board.h> 75 #include <asm/sibyte/sb1250.h> 76 #if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80) 77 #include <asm/sibyte/bcm1480_regs.h> 78 #include <asm/sibyte/bcm1480_int.h> 79 #define R_MAC_DMA_OODPKTLOST_RX R_MAC_DMA_OODPKTLOST 80 #elif defined(CONFIG_SIBYTE_SB1250) || defined(CONFIG_SIBYTE_BCM112X) 81 #include <asm/sibyte/sb1250_regs.h> 82 #include <asm/sibyte/sb1250_int.h> 83 #else 84 #error invalid SiByte MAC configuration 85 #endif 86 #include <asm/sibyte/sb1250_scd.h> 87 #include <asm/sibyte/sb1250_mac.h> 88 #include <asm/sibyte/sb1250_dma.h> 89 90 #if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80) 91 #define UNIT_INT(n) (K_BCM1480_INT_MAC_0 + ((n) * 2)) 92 #elif defined(CONFIG_SIBYTE_SB1250) || defined(CONFIG_SIBYTE_BCM112X) 93 #define UNIT_INT(n) (K_INT_MAC_0 + (n)) 94 #else 95 #error invalid SiByte MAC configuration 96 #endif 97 98 #ifdef K_INT_PHY 99 #define SBMAC_PHY_INT K_INT_PHY 100 #else 101 #define SBMAC_PHY_INT PHY_POLL 102 #endif 103 104 /********************************************************************** 105 * Simple types 106 ********************************************************************* */ 107 108 enum sbmac_speed { 109 sbmac_speed_none = 0, 110 sbmac_speed_10 = SPEED_10, 111 sbmac_speed_100 = SPEED_100, 112 sbmac_speed_1000 = SPEED_1000, 113 }; 114 115 enum sbmac_duplex { 116 sbmac_duplex_none = -1, 117 sbmac_duplex_half = DUPLEX_HALF, 118 sbmac_duplex_full = DUPLEX_FULL, 119 }; 120 121 enum sbmac_fc { 122 sbmac_fc_none, 123 sbmac_fc_disabled, 124 sbmac_fc_frame, 125 sbmac_fc_collision, 126 sbmac_fc_carrier, 127 }; 128 129 enum sbmac_state { 130 sbmac_state_uninit, 131 sbmac_state_off, 132 sbmac_state_on, 133 sbmac_state_broken, 134 }; 135 136 137 /********************************************************************** 138 * Macros 139 ********************************************************************* */ 140 141 142 #define SBDMA_NEXTBUF(d,f) ((((d)->f+1) == (d)->sbdma_dscrtable_end) ? \ 143 (d)->sbdma_dscrtable : (d)->f+1) 144 145 146 #define NUMCACHEBLKS(x) DIV_ROUND_UP(x, SMP_CACHE_BYTES) 147 148 #define SBMAC_MAX_TXDESCR 256 149 #define SBMAC_MAX_RXDESCR 256 150 151 #define ENET_PACKET_SIZE 1518 152 /*#define ENET_PACKET_SIZE 9216 */ 153 154 /********************************************************************** 155 * DMA Descriptor structure 156 ********************************************************************* */ 157 158 struct sbdmadscr { 159 uint64_t dscr_a; 160 uint64_t dscr_b; 161 }; 162 163 /********************************************************************** 164 * DMA Controller structure 165 ********************************************************************* */ 166 167 struct sbmacdma { 168 169 /* 170 * This stuff is used to identify the channel and the registers 171 * associated with it. 172 */ 173 struct sbmac_softc *sbdma_eth; /* back pointer to associated 174 MAC */ 175 int sbdma_channel; /* channel number */ 176 int sbdma_txdir; /* direction (1=transmit) */ 177 int sbdma_maxdescr; /* total # of descriptors 178 in ring */ 179 #ifdef CONFIG_SBMAC_COALESCE 180 int sbdma_int_pktcnt; 181 /* # descriptors rx/tx 182 before interrupt */ 183 int sbdma_int_timeout; 184 /* # usec rx/tx interrupt */ 185 #endif 186 void __iomem *sbdma_config0; /* DMA config register 0 */ 187 void __iomem *sbdma_config1; /* DMA config register 1 */ 188 void __iomem *sbdma_dscrbase; 189 /* descriptor base address */ 190 void __iomem *sbdma_dscrcnt; /* descriptor count register */ 191 void __iomem *sbdma_curdscr; /* current descriptor 192 address */ 193 void __iomem *sbdma_oodpktlost; 194 /* pkt drop (rx only) */ 195 196 /* 197 * This stuff is for maintenance of the ring 198 */ 199 void *sbdma_dscrtable_unaligned; 200 struct sbdmadscr *sbdma_dscrtable; 201 /* base of descriptor table */ 202 struct sbdmadscr *sbdma_dscrtable_end; 203 /* end of descriptor table */ 204 struct sk_buff **sbdma_ctxtable; 205 /* context table, one 206 per descr */ 207 dma_addr_t sbdma_dscrtable_phys; 208 /* and also the phys addr */ 209 struct sbdmadscr *sbdma_addptr; /* next dscr for sw to add */ 210 struct sbdmadscr *sbdma_remptr; /* next dscr for sw 211 to remove */ 212 }; 213 214 215 /********************************************************************** 216 * Ethernet softc structure 217 ********************************************************************* */ 218 219 struct sbmac_softc { 220 221 /* 222 * Linux-specific things 223 */ 224 struct net_device *sbm_dev; /* pointer to linux device */ 225 struct napi_struct napi; 226 struct phy_device *phy_dev; /* the associated PHY device */ 227 struct mii_bus *mii_bus; /* the MII bus */ 228 spinlock_t sbm_lock; /* spin lock */ 229 int sbm_devflags; /* current device flags */ 230 231 /* 232 * Controller-specific things 233 */ 234 void __iomem *sbm_base; /* MAC's base address */ 235 enum sbmac_state sbm_state; /* current state */ 236 237 void __iomem *sbm_macenable; /* MAC Enable Register */ 238 void __iomem *sbm_maccfg; /* MAC Config Register */ 239 void __iomem *sbm_fifocfg; /* FIFO Config Register */ 240 void __iomem *sbm_framecfg; /* Frame Config Register */ 241 void __iomem *sbm_rxfilter; /* Receive Filter Register */ 242 void __iomem *sbm_isr; /* Interrupt Status Register */ 243 void __iomem *sbm_imr; /* Interrupt Mask Register */ 244 void __iomem *sbm_mdio; /* MDIO Register */ 245 246 enum sbmac_speed sbm_speed; /* current speed */ 247 enum sbmac_duplex sbm_duplex; /* current duplex */ 248 enum sbmac_fc sbm_fc; /* cur. flow control setting */ 249 int sbm_pause; /* current pause setting */ 250 int sbm_link; /* current link state */ 251 252 unsigned char sbm_hwaddr[ETH_ALEN]; 253 254 struct sbmacdma sbm_txdma; /* only channel 0 for now */ 255 struct sbmacdma sbm_rxdma; 256 int rx_hw_checksum; 257 int sbe_idx; 258 }; 259 260 261 /********************************************************************** 262 * Externs 263 ********************************************************************* */ 264 265 /********************************************************************** 266 * Prototypes 267 ********************************************************************* */ 268 269 static void sbdma_initctx(struct sbmacdma *d, struct sbmac_softc *s, int chan, 270 int txrx, int maxdescr); 271 static void sbdma_channel_start(struct sbmacdma *d, int rxtx); 272 static int sbdma_add_rcvbuffer(struct sbmac_softc *sc, struct sbmacdma *d, 273 struct sk_buff *m); 274 static int sbdma_add_txbuffer(struct sbmacdma *d, struct sk_buff *m); 275 static void sbdma_emptyring(struct sbmacdma *d); 276 static void sbdma_fillring(struct sbmac_softc *sc, struct sbmacdma *d); 277 static int sbdma_rx_process(struct sbmac_softc *sc, struct sbmacdma *d, 278 int work_to_do, int poll); 279 static void sbdma_tx_process(struct sbmac_softc *sc, struct sbmacdma *d, 280 int poll); 281 static int sbmac_initctx(struct sbmac_softc *s); 282 static void sbmac_channel_start(struct sbmac_softc *s); 283 static void sbmac_channel_stop(struct sbmac_softc *s); 284 static enum sbmac_state sbmac_set_channel_state(struct sbmac_softc *, 285 enum sbmac_state); 286 static void sbmac_promiscuous_mode(struct sbmac_softc *sc, int onoff); 287 static uint64_t sbmac_addr2reg(unsigned char *ptr); 288 static irqreturn_t sbmac_intr(int irq, void *dev_instance); 289 static netdev_tx_t sbmac_start_tx(struct sk_buff *skb, struct net_device *dev); 290 static void sbmac_setmulti(struct sbmac_softc *sc); 291 static int sbmac_init(struct platform_device *pldev, long long base); 292 static int sbmac_set_speed(struct sbmac_softc *s, enum sbmac_speed speed); 293 static int sbmac_set_duplex(struct sbmac_softc *s, enum sbmac_duplex duplex, 294 enum sbmac_fc fc); 295 296 static int sbmac_open(struct net_device *dev); 297 static void sbmac_tx_timeout (struct net_device *dev, unsigned int txqueue); 298 static void sbmac_set_rx_mode(struct net_device *dev); 299 static int sbmac_mii_ioctl(struct net_device *dev, struct ifreq *rq, int cmd); 300 static int sbmac_close(struct net_device *dev); 301 static int sbmac_poll(struct napi_struct *napi, int budget); 302 303 static void sbmac_mii_poll(struct net_device *dev); 304 static int sbmac_mii_probe(struct net_device *dev); 305 306 static void sbmac_mii_sync(void __iomem *sbm_mdio); 307 static void sbmac_mii_senddata(void __iomem *sbm_mdio, unsigned int data, 308 int bitcnt); 309 static int sbmac_mii_read(struct mii_bus *bus, int phyaddr, int regidx); 310 static int sbmac_mii_write(struct mii_bus *bus, int phyaddr, int regidx, 311 u16 val); 312 313 314 /********************************************************************** 315 * Globals 316 ********************************************************************* */ 317 318 static char sbmac_string[] = "sb1250-mac"; 319 320 static char sbmac_mdio_string[] = "sb1250-mac-mdio"; 321 322 323 /********************************************************************** 324 * MDIO constants 325 ********************************************************************* */ 326 327 #define MII_COMMAND_START 0x01 328 #define MII_COMMAND_READ 0x02 329 #define MII_COMMAND_WRITE 0x01 330 #define MII_COMMAND_ACK 0x02 331 332 #define M_MAC_MDIO_DIR_OUTPUT 0 /* for clarity */ 333 334 #define ENABLE 1 335 #define DISABLE 0 336 337 /********************************************************************** 338 * SBMAC_MII_SYNC(sbm_mdio) 339 * 340 * Synchronize with the MII - send a pattern of bits to the MII 341 * that will guarantee that it is ready to accept a command. 342 * 343 * Input parameters: 344 * sbm_mdio - address of the MAC's MDIO register 345 * 346 * Return value: 347 * nothing 348 ********************************************************************* */ 349 350 static void sbmac_mii_sync(void __iomem *sbm_mdio) 351 { 352 int cnt; 353 uint64_t bits; 354 int mac_mdio_genc; 355 356 mac_mdio_genc = __raw_readq(sbm_mdio) & M_MAC_GENC; 357 358 bits = M_MAC_MDIO_DIR_OUTPUT | M_MAC_MDIO_OUT; 359 360 __raw_writeq(bits | mac_mdio_genc, sbm_mdio); 361 362 for (cnt = 0; cnt < 32; cnt++) { 363 __raw_writeq(bits | M_MAC_MDC | mac_mdio_genc, sbm_mdio); 364 __raw_writeq(bits | mac_mdio_genc, sbm_mdio); 365 } 366 } 367 368 /********************************************************************** 369 * SBMAC_MII_SENDDATA(sbm_mdio, data, bitcnt) 370 * 371 * Send some bits to the MII. The bits to be sent are right- 372 * justified in the 'data' parameter. 373 * 374 * Input parameters: 375 * sbm_mdio - address of the MAC's MDIO register 376 * data - data to send 377 * bitcnt - number of bits to send 378 ********************************************************************* */ 379 380 static void sbmac_mii_senddata(void __iomem *sbm_mdio, unsigned int data, 381 int bitcnt) 382 { 383 int i; 384 uint64_t bits; 385 unsigned int curmask; 386 int mac_mdio_genc; 387 388 mac_mdio_genc = __raw_readq(sbm_mdio) & M_MAC_GENC; 389 390 bits = M_MAC_MDIO_DIR_OUTPUT; 391 __raw_writeq(bits | mac_mdio_genc, sbm_mdio); 392 393 curmask = 1 << (bitcnt - 1); 394 395 for (i = 0; i < bitcnt; i++) { 396 if (data & curmask) 397 bits |= M_MAC_MDIO_OUT; 398 else bits &= ~M_MAC_MDIO_OUT; 399 __raw_writeq(bits | mac_mdio_genc, sbm_mdio); 400 __raw_writeq(bits | M_MAC_MDC | mac_mdio_genc, sbm_mdio); 401 __raw_writeq(bits | mac_mdio_genc, sbm_mdio); 402 curmask >>= 1; 403 } 404 } 405 406 407 408 /********************************************************************** 409 * SBMAC_MII_READ(bus, phyaddr, regidx) 410 * Read a PHY register. 411 * 412 * Input parameters: 413 * bus - MDIO bus handle 414 * phyaddr - PHY's address 415 * regnum - index of register to read 416 * 417 * Return value: 418 * value read, or 0xffff if an error occurred. 419 ********************************************************************* */ 420 421 static int sbmac_mii_read(struct mii_bus *bus, int phyaddr, int regidx) 422 { 423 struct sbmac_softc *sc = (struct sbmac_softc *)bus->priv; 424 void __iomem *sbm_mdio = sc->sbm_mdio; 425 int idx; 426 int error; 427 int regval; 428 int mac_mdio_genc; 429 430 /* 431 * Synchronize ourselves so that the PHY knows the next 432 * thing coming down is a command 433 */ 434 sbmac_mii_sync(sbm_mdio); 435 436 /* 437 * Send the data to the PHY. The sequence is 438 * a "start" command (2 bits) 439 * a "read" command (2 bits) 440 * the PHY addr (5 bits) 441 * the register index (5 bits) 442 */ 443 sbmac_mii_senddata(sbm_mdio, MII_COMMAND_START, 2); 444 sbmac_mii_senddata(sbm_mdio, MII_COMMAND_READ, 2); 445 sbmac_mii_senddata(sbm_mdio, phyaddr, 5); 446 sbmac_mii_senddata(sbm_mdio, regidx, 5); 447 448 mac_mdio_genc = __raw_readq(sbm_mdio) & M_MAC_GENC; 449 450 /* 451 * Switch the port around without a clock transition. 452 */ 453 __raw_writeq(M_MAC_MDIO_DIR_INPUT | mac_mdio_genc, sbm_mdio); 454 455 /* 456 * Send out a clock pulse to signal we want the status 457 */ 458 __raw_writeq(M_MAC_MDIO_DIR_INPUT | M_MAC_MDC | mac_mdio_genc, 459 sbm_mdio); 460 __raw_writeq(M_MAC_MDIO_DIR_INPUT | mac_mdio_genc, sbm_mdio); 461 462 /* 463 * If an error occurred, the PHY will signal '1' back 464 */ 465 error = __raw_readq(sbm_mdio) & M_MAC_MDIO_IN; 466 467 /* 468 * Issue an 'idle' clock pulse, but keep the direction 469 * the same. 470 */ 471 __raw_writeq(M_MAC_MDIO_DIR_INPUT | M_MAC_MDC | mac_mdio_genc, 472 sbm_mdio); 473 __raw_writeq(M_MAC_MDIO_DIR_INPUT | mac_mdio_genc, sbm_mdio); 474 475 regval = 0; 476 477 for (idx = 0; idx < 16; idx++) { 478 regval <<= 1; 479 480 if (error == 0) { 481 if (__raw_readq(sbm_mdio) & M_MAC_MDIO_IN) 482 regval |= 1; 483 } 484 485 __raw_writeq(M_MAC_MDIO_DIR_INPUT | M_MAC_MDC | mac_mdio_genc, 486 sbm_mdio); 487 __raw_writeq(M_MAC_MDIO_DIR_INPUT | mac_mdio_genc, sbm_mdio); 488 } 489 490 /* Switch back to output */ 491 __raw_writeq(M_MAC_MDIO_DIR_OUTPUT | mac_mdio_genc, sbm_mdio); 492 493 if (error == 0) 494 return regval; 495 return 0xffff; 496 } 497 498 499 /********************************************************************** 500 * SBMAC_MII_WRITE(bus, phyaddr, regidx, regval) 501 * 502 * Write a value to a PHY register. 503 * 504 * Input parameters: 505 * bus - MDIO bus handle 506 * phyaddr - PHY to use 507 * regidx - register within the PHY 508 * regval - data to write to register 509 * 510 * Return value: 511 * 0 for success 512 ********************************************************************* */ 513 514 static int sbmac_mii_write(struct mii_bus *bus, int phyaddr, int regidx, 515 u16 regval) 516 { 517 struct sbmac_softc *sc = (struct sbmac_softc *)bus->priv; 518 void __iomem *sbm_mdio = sc->sbm_mdio; 519 int mac_mdio_genc; 520 521 sbmac_mii_sync(sbm_mdio); 522 523 sbmac_mii_senddata(sbm_mdio, MII_COMMAND_START, 2); 524 sbmac_mii_senddata(sbm_mdio, MII_COMMAND_WRITE, 2); 525 sbmac_mii_senddata(sbm_mdio, phyaddr, 5); 526 sbmac_mii_senddata(sbm_mdio, regidx, 5); 527 sbmac_mii_senddata(sbm_mdio, MII_COMMAND_ACK, 2); 528 sbmac_mii_senddata(sbm_mdio, regval, 16); 529 530 mac_mdio_genc = __raw_readq(sbm_mdio) & M_MAC_GENC; 531 532 __raw_writeq(M_MAC_MDIO_DIR_OUTPUT | mac_mdio_genc, sbm_mdio); 533 534 return 0; 535 } 536 537 538 539 /********************************************************************** 540 * SBDMA_INITCTX(d,s,chan,txrx,maxdescr) 541 * 542 * Initialize a DMA channel context. Since there are potentially 543 * eight DMA channels per MAC, it's nice to do this in a standard 544 * way. 545 * 546 * Input parameters: 547 * d - struct sbmacdma (DMA channel context) 548 * s - struct sbmac_softc (pointer to a MAC) 549 * chan - channel number (0..1 right now) 550 * txrx - Identifies DMA_TX or DMA_RX for channel direction 551 * maxdescr - number of descriptors 552 * 553 * Return value: 554 * nothing 555 ********************************************************************* */ 556 557 static void sbdma_initctx(struct sbmacdma *d, struct sbmac_softc *s, int chan, 558 int txrx, int maxdescr) 559 { 560 #ifdef CONFIG_SBMAC_COALESCE 561 int int_pktcnt, int_timeout; 562 #endif 563 564 /* 565 * Save away interesting stuff in the structure 566 */ 567 568 d->sbdma_eth = s; 569 d->sbdma_channel = chan; 570 d->sbdma_txdir = txrx; 571 572 #if 0 573 /* RMON clearing */ 574 s->sbe_idx =(s->sbm_base - A_MAC_BASE_0)/MAC_SPACING; 575 #endif 576 577 __raw_writeq(0, s->sbm_base + R_MAC_RMON_TX_BYTES); 578 __raw_writeq(0, s->sbm_base + R_MAC_RMON_COLLISIONS); 579 __raw_writeq(0, s->sbm_base + R_MAC_RMON_LATE_COL); 580 __raw_writeq(0, s->sbm_base + R_MAC_RMON_EX_COL); 581 __raw_writeq(0, s->sbm_base + R_MAC_RMON_FCS_ERROR); 582 __raw_writeq(0, s->sbm_base + R_MAC_RMON_TX_ABORT); 583 __raw_writeq(0, s->sbm_base + R_MAC_RMON_TX_BAD); 584 __raw_writeq(0, s->sbm_base + R_MAC_RMON_TX_GOOD); 585 __raw_writeq(0, s->sbm_base + R_MAC_RMON_TX_RUNT); 586 __raw_writeq(0, s->sbm_base + R_MAC_RMON_TX_OVERSIZE); 587 __raw_writeq(0, s->sbm_base + R_MAC_RMON_RX_BYTES); 588 __raw_writeq(0, s->sbm_base + R_MAC_RMON_RX_MCAST); 589 __raw_writeq(0, s->sbm_base + R_MAC_RMON_RX_BCAST); 590 __raw_writeq(0, s->sbm_base + R_MAC_RMON_RX_BAD); 591 __raw_writeq(0, s->sbm_base + R_MAC_RMON_RX_GOOD); 592 __raw_writeq(0, s->sbm_base + R_MAC_RMON_RX_RUNT); 593 __raw_writeq(0, s->sbm_base + R_MAC_RMON_RX_OVERSIZE); 594 __raw_writeq(0, s->sbm_base + R_MAC_RMON_RX_FCS_ERROR); 595 __raw_writeq(0, s->sbm_base + R_MAC_RMON_RX_LENGTH_ERROR); 596 __raw_writeq(0, s->sbm_base + R_MAC_RMON_RX_CODE_ERROR); 597 __raw_writeq(0, s->sbm_base + R_MAC_RMON_RX_ALIGN_ERROR); 598 599 /* 600 * initialize register pointers 601 */ 602 603 d->sbdma_config0 = 604 s->sbm_base + R_MAC_DMA_REGISTER(txrx,chan,R_MAC_DMA_CONFIG0); 605 d->sbdma_config1 = 606 s->sbm_base + R_MAC_DMA_REGISTER(txrx,chan,R_MAC_DMA_CONFIG1); 607 d->sbdma_dscrbase = 608 s->sbm_base + R_MAC_DMA_REGISTER(txrx,chan,R_MAC_DMA_DSCR_BASE); 609 d->sbdma_dscrcnt = 610 s->sbm_base + R_MAC_DMA_REGISTER(txrx,chan,R_MAC_DMA_DSCR_CNT); 611 d->sbdma_curdscr = 612 s->sbm_base + R_MAC_DMA_REGISTER(txrx,chan,R_MAC_DMA_CUR_DSCRADDR); 613 if (d->sbdma_txdir) 614 d->sbdma_oodpktlost = NULL; 615 else 616 d->sbdma_oodpktlost = 617 s->sbm_base + R_MAC_DMA_REGISTER(txrx,chan,R_MAC_DMA_OODPKTLOST_RX); 618 619 /* 620 * Allocate memory for the ring 621 */ 622 623 d->sbdma_maxdescr = maxdescr; 624 625 d->sbdma_dscrtable_unaligned = kcalloc(d->sbdma_maxdescr + 1, 626 sizeof(*d->sbdma_dscrtable), 627 GFP_KERNEL); 628 629 /* 630 * The descriptor table must be aligned to at least 16 bytes or the 631 * MAC will corrupt it. 632 */ 633 d->sbdma_dscrtable = (struct sbdmadscr *) 634 ALIGN((unsigned long)d->sbdma_dscrtable_unaligned, 635 sizeof(*d->sbdma_dscrtable)); 636 637 d->sbdma_dscrtable_end = d->sbdma_dscrtable + d->sbdma_maxdescr; 638 639 d->sbdma_dscrtable_phys = virt_to_phys(d->sbdma_dscrtable); 640 641 /* 642 * And context table 643 */ 644 645 d->sbdma_ctxtable = kcalloc(d->sbdma_maxdescr, 646 sizeof(*d->sbdma_ctxtable), GFP_KERNEL); 647 648 #ifdef CONFIG_SBMAC_COALESCE 649 /* 650 * Setup Rx/Tx DMA coalescing defaults 651 */ 652 653 int_pktcnt = (txrx == DMA_TX) ? int_pktcnt_tx : int_pktcnt_rx; 654 if ( int_pktcnt ) { 655 d->sbdma_int_pktcnt = int_pktcnt; 656 } else { 657 d->sbdma_int_pktcnt = 1; 658 } 659 660 int_timeout = (txrx == DMA_TX) ? int_timeout_tx : int_timeout_rx; 661 if ( int_timeout ) { 662 d->sbdma_int_timeout = int_timeout; 663 } else { 664 d->sbdma_int_timeout = 0; 665 } 666 #endif 667 668 } 669 670 /********************************************************************** 671 * SBDMA_CHANNEL_START(d) 672 * 673 * Initialize the hardware registers for a DMA channel. 674 * 675 * Input parameters: 676 * d - DMA channel to init (context must be previously init'd 677 * rxtx - DMA_RX or DMA_TX depending on what type of channel 678 * 679 * Return value: 680 * nothing 681 ********************************************************************* */ 682 683 static void sbdma_channel_start(struct sbmacdma *d, int rxtx) 684 { 685 /* 686 * Turn on the DMA channel 687 */ 688 689 #ifdef CONFIG_SBMAC_COALESCE 690 __raw_writeq(V_DMA_INT_TIMEOUT(d->sbdma_int_timeout) | 691 0, d->sbdma_config1); 692 __raw_writeq(M_DMA_EOP_INT_EN | 693 V_DMA_RINGSZ(d->sbdma_maxdescr) | 694 V_DMA_INT_PKTCNT(d->sbdma_int_pktcnt) | 695 0, d->sbdma_config0); 696 #else 697 __raw_writeq(0, d->sbdma_config1); 698 __raw_writeq(V_DMA_RINGSZ(d->sbdma_maxdescr) | 699 0, d->sbdma_config0); 700 #endif 701 702 __raw_writeq(d->sbdma_dscrtable_phys, d->sbdma_dscrbase); 703 704 /* 705 * Initialize ring pointers 706 */ 707 708 d->sbdma_addptr = d->sbdma_dscrtable; 709 d->sbdma_remptr = d->sbdma_dscrtable; 710 } 711 712 /********************************************************************** 713 * SBDMA_CHANNEL_STOP(d) 714 * 715 * Initialize the hardware registers for a DMA channel. 716 * 717 * Input parameters: 718 * d - DMA channel to init (context must be previously init'd 719 * 720 * Return value: 721 * nothing 722 ********************************************************************* */ 723 724 static void sbdma_channel_stop(struct sbmacdma *d) 725 { 726 /* 727 * Turn off the DMA channel 728 */ 729 730 __raw_writeq(0, d->sbdma_config1); 731 732 __raw_writeq(0, d->sbdma_dscrbase); 733 734 __raw_writeq(0, d->sbdma_config0); 735 736 /* 737 * Zero ring pointers 738 */ 739 740 d->sbdma_addptr = NULL; 741 d->sbdma_remptr = NULL; 742 } 743 744 static inline void sbdma_align_skb(struct sk_buff *skb, 745 unsigned int power2, unsigned int offset) 746 { 747 unsigned char *addr = skb->data; 748 unsigned char *newaddr = PTR_ALIGN(addr, power2); 749 750 skb_reserve(skb, newaddr - addr + offset); 751 } 752 753 754 /********************************************************************** 755 * SBDMA_ADD_RCVBUFFER(d,sb) 756 * 757 * Add a buffer to the specified DMA channel. For receive channels, 758 * this queues a buffer for inbound packets. 759 * 760 * Input parameters: 761 * sc - softc structure 762 * d - DMA channel descriptor 763 * sb - sk_buff to add, or NULL if we should allocate one 764 * 765 * Return value: 766 * 0 if buffer could not be added (ring is full) 767 * 1 if buffer added successfully 768 ********************************************************************* */ 769 770 771 static int sbdma_add_rcvbuffer(struct sbmac_softc *sc, struct sbmacdma *d, 772 struct sk_buff *sb) 773 { 774 struct net_device *dev = sc->sbm_dev; 775 struct sbdmadscr *dsc; 776 struct sbdmadscr *nextdsc; 777 struct sk_buff *sb_new = NULL; 778 int pktsize = ENET_PACKET_SIZE; 779 780 /* get pointer to our current place in the ring */ 781 782 dsc = d->sbdma_addptr; 783 nextdsc = SBDMA_NEXTBUF(d,sbdma_addptr); 784 785 /* 786 * figure out if the ring is full - if the next descriptor 787 * is the same as the one that we're going to remove from 788 * the ring, the ring is full 789 */ 790 791 if (nextdsc == d->sbdma_remptr) { 792 return -ENOSPC; 793 } 794 795 /* 796 * Allocate a sk_buff if we don't already have one. 797 * If we do have an sk_buff, reset it so that it's empty. 798 * 799 * Note: sk_buffs don't seem to be guaranteed to have any sort 800 * of alignment when they are allocated. Therefore, allocate enough 801 * extra space to make sure that: 802 * 803 * 1. the data does not start in the middle of a cache line. 804 * 2. The data does not end in the middle of a cache line 805 * 3. The buffer can be aligned such that the IP addresses are 806 * naturally aligned. 807 * 808 * Remember, the SOCs MAC writes whole cache lines at a time, 809 * without reading the old contents first. So, if the sk_buff's 810 * data portion starts in the middle of a cache line, the SOC 811 * DMA will trash the beginning (and ending) portions. 812 */ 813 814 if (sb == NULL) { 815 sb_new = netdev_alloc_skb(dev, ENET_PACKET_SIZE + 816 SMP_CACHE_BYTES * 2 + 817 NET_IP_ALIGN); 818 if (sb_new == NULL) 819 return -ENOBUFS; 820 821 sbdma_align_skb(sb_new, SMP_CACHE_BYTES, NET_IP_ALIGN); 822 } 823 else { 824 sb_new = sb; 825 /* 826 * nothing special to reinit buffer, it's already aligned 827 * and sb->data already points to a good place. 828 */ 829 } 830 831 /* 832 * fill in the descriptor 833 */ 834 835 #ifdef CONFIG_SBMAC_COALESCE 836 /* 837 * Do not interrupt per DMA transfer. 838 */ 839 dsc->dscr_a = virt_to_phys(sb_new->data) | 840 V_DMA_DSCRA_A_SIZE(NUMCACHEBLKS(pktsize + NET_IP_ALIGN)) | 0; 841 #else 842 dsc->dscr_a = virt_to_phys(sb_new->data) | 843 V_DMA_DSCRA_A_SIZE(NUMCACHEBLKS(pktsize + NET_IP_ALIGN)) | 844 M_DMA_DSCRA_INTERRUPT; 845 #endif 846 847 /* receiving: no options */ 848 dsc->dscr_b = 0; 849 850 /* 851 * fill in the context 852 */ 853 854 d->sbdma_ctxtable[dsc-d->sbdma_dscrtable] = sb_new; 855 856 /* 857 * point at next packet 858 */ 859 860 d->sbdma_addptr = nextdsc; 861 862 /* 863 * Give the buffer to the DMA engine. 864 */ 865 866 __raw_writeq(1, d->sbdma_dscrcnt); 867 868 return 0; /* we did it */ 869 } 870 871 /********************************************************************** 872 * SBDMA_ADD_TXBUFFER(d,sb) 873 * 874 * Add a transmit buffer to the specified DMA channel, causing a 875 * transmit to start. 876 * 877 * Input parameters: 878 * d - DMA channel descriptor 879 * sb - sk_buff to add 880 * 881 * Return value: 882 * 0 transmit queued successfully 883 * otherwise error code 884 ********************************************************************* */ 885 886 887 static int sbdma_add_txbuffer(struct sbmacdma *d, struct sk_buff *sb) 888 { 889 struct sbdmadscr *dsc; 890 struct sbdmadscr *nextdsc; 891 uint64_t phys; 892 uint64_t ncb; 893 int length; 894 895 /* get pointer to our current place in the ring */ 896 897 dsc = d->sbdma_addptr; 898 nextdsc = SBDMA_NEXTBUF(d,sbdma_addptr); 899 900 /* 901 * figure out if the ring is full - if the next descriptor 902 * is the same as the one that we're going to remove from 903 * the ring, the ring is full 904 */ 905 906 if (nextdsc == d->sbdma_remptr) { 907 return -ENOSPC; 908 } 909 910 /* 911 * Under Linux, it's not necessary to copy/coalesce buffers 912 * like it is on NetBSD. We think they're all contiguous, 913 * but that may not be true for GBE. 914 */ 915 916 length = sb->len; 917 918 /* 919 * fill in the descriptor. Note that the number of cache 920 * blocks in the descriptor is the number of blocks 921 * *spanned*, so we need to add in the offset (if any) 922 * while doing the calculation. 923 */ 924 925 phys = virt_to_phys(sb->data); 926 ncb = NUMCACHEBLKS(length+(phys & (SMP_CACHE_BYTES - 1))); 927 928 dsc->dscr_a = phys | 929 V_DMA_DSCRA_A_SIZE(ncb) | 930 #ifndef CONFIG_SBMAC_COALESCE 931 M_DMA_DSCRA_INTERRUPT | 932 #endif 933 M_DMA_ETHTX_SOP; 934 935 /* transmitting: set outbound options and length */ 936 937 dsc->dscr_b = V_DMA_DSCRB_OPTIONS(K_DMA_ETHTX_APPENDCRC_APPENDPAD) | 938 V_DMA_DSCRB_PKT_SIZE(length); 939 940 /* 941 * fill in the context 942 */ 943 944 d->sbdma_ctxtable[dsc-d->sbdma_dscrtable] = sb; 945 946 /* 947 * point at next packet 948 */ 949 950 d->sbdma_addptr = nextdsc; 951 952 /* 953 * Give the buffer to the DMA engine. 954 */ 955 956 __raw_writeq(1, d->sbdma_dscrcnt); 957 958 return 0; /* we did it */ 959 } 960 961 962 963 964 /********************************************************************** 965 * SBDMA_EMPTYRING(d) 966 * 967 * Free all allocated sk_buffs on the specified DMA channel; 968 * 969 * Input parameters: 970 * d - DMA channel 971 * 972 * Return value: 973 * nothing 974 ********************************************************************* */ 975 976 static void sbdma_emptyring(struct sbmacdma *d) 977 { 978 int idx; 979 struct sk_buff *sb; 980 981 for (idx = 0; idx < d->sbdma_maxdescr; idx++) { 982 sb = d->sbdma_ctxtable[idx]; 983 if (sb) { 984 dev_kfree_skb(sb); 985 d->sbdma_ctxtable[idx] = NULL; 986 } 987 } 988 } 989 990 991 /********************************************************************** 992 * SBDMA_FILLRING(d) 993 * 994 * Fill the specified DMA channel (must be receive channel) 995 * with sk_buffs 996 * 997 * Input parameters: 998 * sc - softc structure 999 * d - DMA channel 1000 * 1001 * Return value: 1002 * nothing 1003 ********************************************************************* */ 1004 1005 static void sbdma_fillring(struct sbmac_softc *sc, struct sbmacdma *d) 1006 { 1007 int idx; 1008 1009 for (idx = 0; idx < SBMAC_MAX_RXDESCR - 1; idx++) { 1010 if (sbdma_add_rcvbuffer(sc, d, NULL) != 0) 1011 break; 1012 } 1013 } 1014 1015 #ifdef CONFIG_NET_POLL_CONTROLLER 1016 static void sbmac_netpoll(struct net_device *netdev) 1017 { 1018 struct sbmac_softc *sc = netdev_priv(netdev); 1019 int irq = sc->sbm_dev->irq; 1020 1021 __raw_writeq(0, sc->sbm_imr); 1022 1023 sbmac_intr(irq, netdev); 1024 1025 #ifdef CONFIG_SBMAC_COALESCE 1026 __raw_writeq(((M_MAC_INT_EOP_COUNT | M_MAC_INT_EOP_TIMER) << S_MAC_TX_CH0) | 1027 ((M_MAC_INT_EOP_COUNT | M_MAC_INT_EOP_TIMER) << S_MAC_RX_CH0), 1028 sc->sbm_imr); 1029 #else 1030 __raw_writeq((M_MAC_INT_CHANNEL << S_MAC_TX_CH0) | 1031 (M_MAC_INT_CHANNEL << S_MAC_RX_CH0), sc->sbm_imr); 1032 #endif 1033 } 1034 #endif 1035 1036 /********************************************************************** 1037 * SBDMA_RX_PROCESS(sc,d,work_to_do,poll) 1038 * 1039 * Process "completed" receive buffers on the specified DMA channel. 1040 * 1041 * Input parameters: 1042 * sc - softc structure 1043 * d - DMA channel context 1044 * work_to_do - no. of packets to process before enabling interrupt 1045 * again (for NAPI) 1046 * poll - 1: using polling (for NAPI) 1047 * 1048 * Return value: 1049 * nothing 1050 ********************************************************************* */ 1051 1052 static int sbdma_rx_process(struct sbmac_softc *sc, struct sbmacdma *d, 1053 int work_to_do, int poll) 1054 { 1055 struct net_device *dev = sc->sbm_dev; 1056 int curidx; 1057 int hwidx; 1058 struct sbdmadscr *dsc; 1059 struct sk_buff *sb; 1060 int len; 1061 int work_done = 0; 1062 int dropped = 0; 1063 1064 prefetch(d); 1065 1066 again: 1067 /* Check if the HW dropped any frames */ 1068 dev->stats.rx_fifo_errors 1069 += __raw_readq(sc->sbm_rxdma.sbdma_oodpktlost) & 0xffff; 1070 __raw_writeq(0, sc->sbm_rxdma.sbdma_oodpktlost); 1071 1072 while (work_to_do-- > 0) { 1073 /* 1074 * figure out where we are (as an index) and where 1075 * the hardware is (also as an index) 1076 * 1077 * This could be done faster if (for example) the 1078 * descriptor table was page-aligned and contiguous in 1079 * both virtual and physical memory -- you could then 1080 * just compare the low-order bits of the virtual address 1081 * (sbdma_remptr) and the physical address (sbdma_curdscr CSR) 1082 */ 1083 1084 dsc = d->sbdma_remptr; 1085 curidx = dsc - d->sbdma_dscrtable; 1086 1087 prefetch(dsc); 1088 prefetch(&d->sbdma_ctxtable[curidx]); 1089 1090 hwidx = ((__raw_readq(d->sbdma_curdscr) & M_DMA_CURDSCR_ADDR) - 1091 d->sbdma_dscrtable_phys) / 1092 sizeof(*d->sbdma_dscrtable); 1093 1094 /* 1095 * If they're the same, that means we've processed all 1096 * of the descriptors up to (but not including) the one that 1097 * the hardware is working on right now. 1098 */ 1099 1100 if (curidx == hwidx) 1101 goto done; 1102 1103 /* 1104 * Otherwise, get the packet's sk_buff ptr back 1105 */ 1106 1107 sb = d->sbdma_ctxtable[curidx]; 1108 d->sbdma_ctxtable[curidx] = NULL; 1109 1110 len = (int)G_DMA_DSCRB_PKT_SIZE(dsc->dscr_b) - 4; 1111 1112 /* 1113 * Check packet status. If good, process it. 1114 * If not, silently drop it and put it back on the 1115 * receive ring. 1116 */ 1117 1118 if (likely (!(dsc->dscr_a & M_DMA_ETHRX_BAD))) { 1119 1120 /* 1121 * Add a new buffer to replace the old one. If we fail 1122 * to allocate a buffer, we're going to drop this 1123 * packet and put it right back on the receive ring. 1124 */ 1125 1126 if (unlikely(sbdma_add_rcvbuffer(sc, d, NULL) == 1127 -ENOBUFS)) { 1128 dev->stats.rx_dropped++; 1129 /* Re-add old buffer */ 1130 sbdma_add_rcvbuffer(sc, d, sb); 1131 /* No point in continuing at the moment */ 1132 printk(KERN_ERR "dropped packet (1)\n"); 1133 d->sbdma_remptr = SBDMA_NEXTBUF(d,sbdma_remptr); 1134 goto done; 1135 } else { 1136 /* 1137 * Set length into the packet 1138 */ 1139 skb_put(sb,len); 1140 1141 /* 1142 * Buffer has been replaced on the 1143 * receive ring. Pass the buffer to 1144 * the kernel 1145 */ 1146 sb->protocol = eth_type_trans(sb,d->sbdma_eth->sbm_dev); 1147 /* Check hw IPv4/TCP checksum if supported */ 1148 if (sc->rx_hw_checksum == ENABLE) { 1149 if (!((dsc->dscr_a) & M_DMA_ETHRX_BADIP4CS) && 1150 !((dsc->dscr_a) & M_DMA_ETHRX_BADTCPCS)) { 1151 sb->ip_summed = CHECKSUM_UNNECESSARY; 1152 /* don't need to set sb->csum */ 1153 } else { 1154 skb_checksum_none_assert(sb); 1155 } 1156 } 1157 prefetch(sb->data); 1158 prefetch((const void *)(((char *)sb->data)+32)); 1159 if (poll) 1160 dropped = netif_receive_skb(sb); 1161 else 1162 dropped = netif_rx(sb); 1163 1164 if (dropped == NET_RX_DROP) { 1165 dev->stats.rx_dropped++; 1166 d->sbdma_remptr = SBDMA_NEXTBUF(d,sbdma_remptr); 1167 goto done; 1168 } 1169 else { 1170 dev->stats.rx_bytes += len; 1171 dev->stats.rx_packets++; 1172 } 1173 } 1174 } else { 1175 /* 1176 * Packet was mangled somehow. Just drop it and 1177 * put it back on the receive ring. 1178 */ 1179 dev->stats.rx_errors++; 1180 sbdma_add_rcvbuffer(sc, d, sb); 1181 } 1182 1183 1184 /* 1185 * .. and advance to the next buffer. 1186 */ 1187 1188 d->sbdma_remptr = SBDMA_NEXTBUF(d,sbdma_remptr); 1189 work_done++; 1190 } 1191 if (!poll) { 1192 work_to_do = 32; 1193 goto again; /* collect fifo drop statistics again */ 1194 } 1195 done: 1196 return work_done; 1197 } 1198 1199 /********************************************************************** 1200 * SBDMA_TX_PROCESS(sc,d) 1201 * 1202 * Process "completed" transmit buffers on the specified DMA channel. 1203 * This is normally called within the interrupt service routine. 1204 * Note that this isn't really ideal for priority channels, since 1205 * it processes all of the packets on a given channel before 1206 * returning. 1207 * 1208 * Input parameters: 1209 * sc - softc structure 1210 * d - DMA channel context 1211 * poll - 1: using polling (for NAPI) 1212 * 1213 * Return value: 1214 * nothing 1215 ********************************************************************* */ 1216 1217 static void sbdma_tx_process(struct sbmac_softc *sc, struct sbmacdma *d, 1218 int poll) 1219 { 1220 struct net_device *dev = sc->sbm_dev; 1221 int curidx; 1222 int hwidx; 1223 struct sbdmadscr *dsc; 1224 struct sk_buff *sb; 1225 unsigned long flags; 1226 int packets_handled = 0; 1227 1228 spin_lock_irqsave(&(sc->sbm_lock), flags); 1229 1230 if (d->sbdma_remptr == d->sbdma_addptr) 1231 goto end_unlock; 1232 1233 hwidx = ((__raw_readq(d->sbdma_curdscr) & M_DMA_CURDSCR_ADDR) - 1234 d->sbdma_dscrtable_phys) / sizeof(*d->sbdma_dscrtable); 1235 1236 for (;;) { 1237 /* 1238 * figure out where we are (as an index) and where 1239 * the hardware is (also as an index) 1240 * 1241 * This could be done faster if (for example) the 1242 * descriptor table was page-aligned and contiguous in 1243 * both virtual and physical memory -- you could then 1244 * just compare the low-order bits of the virtual address 1245 * (sbdma_remptr) and the physical address (sbdma_curdscr CSR) 1246 */ 1247 1248 curidx = d->sbdma_remptr - d->sbdma_dscrtable; 1249 1250 /* 1251 * If they're the same, that means we've processed all 1252 * of the descriptors up to (but not including) the one that 1253 * the hardware is working on right now. 1254 */ 1255 1256 if (curidx == hwidx) 1257 break; 1258 1259 /* 1260 * Otherwise, get the packet's sk_buff ptr back 1261 */ 1262 1263 dsc = &(d->sbdma_dscrtable[curidx]); 1264 sb = d->sbdma_ctxtable[curidx]; 1265 d->sbdma_ctxtable[curidx] = NULL; 1266 1267 /* 1268 * Stats 1269 */ 1270 1271 dev->stats.tx_bytes += sb->len; 1272 dev->stats.tx_packets++; 1273 1274 /* 1275 * for transmits, we just free buffers. 1276 */ 1277 1278 dev_consume_skb_irq(sb); 1279 1280 /* 1281 * .. and advance to the next buffer. 1282 */ 1283 1284 d->sbdma_remptr = SBDMA_NEXTBUF(d,sbdma_remptr); 1285 1286 packets_handled++; 1287 1288 } 1289 1290 /* 1291 * Decide if we should wake up the protocol or not. 1292 * Other drivers seem to do this when we reach a low 1293 * watermark on the transmit queue. 1294 */ 1295 1296 if (packets_handled) 1297 netif_wake_queue(d->sbdma_eth->sbm_dev); 1298 1299 end_unlock: 1300 spin_unlock_irqrestore(&(sc->sbm_lock), flags); 1301 1302 } 1303 1304 1305 1306 /********************************************************************** 1307 * SBMAC_INITCTX(s) 1308 * 1309 * Initialize an Ethernet context structure - this is called 1310 * once per MAC on the 1250. Memory is allocated here, so don't 1311 * call it again from inside the ioctl routines that bring the 1312 * interface up/down 1313 * 1314 * Input parameters: 1315 * s - sbmac context structure 1316 * 1317 * Return value: 1318 * 0 1319 ********************************************************************* */ 1320 1321 static int sbmac_initctx(struct sbmac_softc *s) 1322 { 1323 1324 /* 1325 * figure out the addresses of some ports 1326 */ 1327 1328 s->sbm_macenable = s->sbm_base + R_MAC_ENABLE; 1329 s->sbm_maccfg = s->sbm_base + R_MAC_CFG; 1330 s->sbm_fifocfg = s->sbm_base + R_MAC_THRSH_CFG; 1331 s->sbm_framecfg = s->sbm_base + R_MAC_FRAMECFG; 1332 s->sbm_rxfilter = s->sbm_base + R_MAC_ADFILTER_CFG; 1333 s->sbm_isr = s->sbm_base + R_MAC_STATUS; 1334 s->sbm_imr = s->sbm_base + R_MAC_INT_MASK; 1335 s->sbm_mdio = s->sbm_base + R_MAC_MDIO; 1336 1337 /* 1338 * Initialize the DMA channels. Right now, only one per MAC is used 1339 * Note: Only do this _once_, as it allocates memory from the kernel! 1340 */ 1341 1342 sbdma_initctx(&(s->sbm_txdma),s,0,DMA_TX,SBMAC_MAX_TXDESCR); 1343 sbdma_initctx(&(s->sbm_rxdma),s,0,DMA_RX,SBMAC_MAX_RXDESCR); 1344 1345 /* 1346 * initial state is OFF 1347 */ 1348 1349 s->sbm_state = sbmac_state_off; 1350 1351 return 0; 1352 } 1353 1354 1355 static void sbdma_uninitctx(struct sbmacdma *d) 1356 { 1357 kfree(d->sbdma_dscrtable_unaligned); 1358 d->sbdma_dscrtable_unaligned = d->sbdma_dscrtable = NULL; 1359 1360 kfree(d->sbdma_ctxtable); 1361 d->sbdma_ctxtable = NULL; 1362 } 1363 1364 1365 static void sbmac_uninitctx(struct sbmac_softc *sc) 1366 { 1367 sbdma_uninitctx(&(sc->sbm_txdma)); 1368 sbdma_uninitctx(&(sc->sbm_rxdma)); 1369 } 1370 1371 1372 /********************************************************************** 1373 * SBMAC_CHANNEL_START(s) 1374 * 1375 * Start packet processing on this MAC. 1376 * 1377 * Input parameters: 1378 * s - sbmac structure 1379 * 1380 * Return value: 1381 * nothing 1382 ********************************************************************* */ 1383 1384 static void sbmac_channel_start(struct sbmac_softc *s) 1385 { 1386 uint64_t reg; 1387 void __iomem *port; 1388 uint64_t cfg,fifo,framecfg; 1389 int idx, th_value; 1390 1391 /* 1392 * Don't do this if running 1393 */ 1394 1395 if (s->sbm_state == sbmac_state_on) 1396 return; 1397 1398 /* 1399 * Bring the controller out of reset, but leave it off. 1400 */ 1401 1402 __raw_writeq(0, s->sbm_macenable); 1403 1404 /* 1405 * Ignore all received packets 1406 */ 1407 1408 __raw_writeq(0, s->sbm_rxfilter); 1409 1410 /* 1411 * Calculate values for various control registers. 1412 */ 1413 1414 cfg = M_MAC_RETRY_EN | 1415 M_MAC_TX_HOLD_SOP_EN | 1416 V_MAC_TX_PAUSE_CNT_16K | 1417 M_MAC_AP_STAT_EN | 1418 M_MAC_FAST_SYNC | 1419 M_MAC_SS_EN | 1420 0; 1421 1422 /* 1423 * Be sure that RD_THRSH+WR_THRSH <= 32 for pass1 pars 1424 * and make sure that RD_THRSH + WR_THRSH <=128 for pass2 and above 1425 * Use a larger RD_THRSH for gigabit 1426 */ 1427 if (soc_type == K_SYS_SOC_TYPE_BCM1250 && periph_rev < 2) 1428 th_value = 28; 1429 else 1430 th_value = 64; 1431 1432 fifo = V_MAC_TX_WR_THRSH(4) | /* Must be '4' or '8' */ 1433 ((s->sbm_speed == sbmac_speed_1000) 1434 ? V_MAC_TX_RD_THRSH(th_value) : V_MAC_TX_RD_THRSH(4)) | 1435 V_MAC_TX_RL_THRSH(4) | 1436 V_MAC_RX_PL_THRSH(4) | 1437 V_MAC_RX_RD_THRSH(4) | /* Must be '4' */ 1438 V_MAC_RX_RL_THRSH(8) | 1439 0; 1440 1441 framecfg = V_MAC_MIN_FRAMESZ_DEFAULT | 1442 V_MAC_MAX_FRAMESZ_DEFAULT | 1443 V_MAC_BACKOFF_SEL(1); 1444 1445 /* 1446 * Clear out the hash address map 1447 */ 1448 1449 port = s->sbm_base + R_MAC_HASH_BASE; 1450 for (idx = 0; idx < MAC_HASH_COUNT; idx++) { 1451 __raw_writeq(0, port); 1452 port += sizeof(uint64_t); 1453 } 1454 1455 /* 1456 * Clear out the exact-match table 1457 */ 1458 1459 port = s->sbm_base + R_MAC_ADDR_BASE; 1460 for (idx = 0; idx < MAC_ADDR_COUNT; idx++) { 1461 __raw_writeq(0, port); 1462 port += sizeof(uint64_t); 1463 } 1464 1465 /* 1466 * Clear out the DMA Channel mapping table registers 1467 */ 1468 1469 port = s->sbm_base + R_MAC_CHUP0_BASE; 1470 for (idx = 0; idx < MAC_CHMAP_COUNT; idx++) { 1471 __raw_writeq(0, port); 1472 port += sizeof(uint64_t); 1473 } 1474 1475 1476 port = s->sbm_base + R_MAC_CHLO0_BASE; 1477 for (idx = 0; idx < MAC_CHMAP_COUNT; idx++) { 1478 __raw_writeq(0, port); 1479 port += sizeof(uint64_t); 1480 } 1481 1482 /* 1483 * Program the hardware address. It goes into the hardware-address 1484 * register as well as the first filter register. 1485 */ 1486 1487 reg = sbmac_addr2reg(s->sbm_hwaddr); 1488 1489 port = s->sbm_base + R_MAC_ADDR_BASE; 1490 __raw_writeq(reg, port); 1491 port = s->sbm_base + R_MAC_ETHERNET_ADDR; 1492 1493 __raw_writeq(reg, port); 1494 1495 /* 1496 * Set the receive filter for no packets, and write values 1497 * to the various config registers 1498 */ 1499 1500 __raw_writeq(0, s->sbm_rxfilter); 1501 __raw_writeq(0, s->sbm_imr); 1502 __raw_writeq(framecfg, s->sbm_framecfg); 1503 __raw_writeq(fifo, s->sbm_fifocfg); 1504 __raw_writeq(cfg, s->sbm_maccfg); 1505 1506 /* 1507 * Initialize DMA channels (rings should be ok now) 1508 */ 1509 1510 sbdma_channel_start(&(s->sbm_rxdma), DMA_RX); 1511 sbdma_channel_start(&(s->sbm_txdma), DMA_TX); 1512 1513 /* 1514 * Configure the speed, duplex, and flow control 1515 */ 1516 1517 sbmac_set_speed(s,s->sbm_speed); 1518 sbmac_set_duplex(s,s->sbm_duplex,s->sbm_fc); 1519 1520 /* 1521 * Fill the receive ring 1522 */ 1523 1524 sbdma_fillring(s, &(s->sbm_rxdma)); 1525 1526 /* 1527 * Turn on the rest of the bits in the enable register 1528 */ 1529 1530 #if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80) 1531 __raw_writeq(M_MAC_RXDMA_EN0 | 1532 M_MAC_TXDMA_EN0, s->sbm_macenable); 1533 #elif defined(CONFIG_SIBYTE_SB1250) || defined(CONFIG_SIBYTE_BCM112X) 1534 __raw_writeq(M_MAC_RXDMA_EN0 | 1535 M_MAC_TXDMA_EN0 | 1536 M_MAC_RX_ENABLE | 1537 M_MAC_TX_ENABLE, s->sbm_macenable); 1538 #else 1539 #error invalid SiByte MAC configuration 1540 #endif 1541 1542 #ifdef CONFIG_SBMAC_COALESCE 1543 __raw_writeq(((M_MAC_INT_EOP_COUNT | M_MAC_INT_EOP_TIMER) << S_MAC_TX_CH0) | 1544 ((M_MAC_INT_EOP_COUNT | M_MAC_INT_EOP_TIMER) << S_MAC_RX_CH0), s->sbm_imr); 1545 #else 1546 __raw_writeq((M_MAC_INT_CHANNEL << S_MAC_TX_CH0) | 1547 (M_MAC_INT_CHANNEL << S_MAC_RX_CH0), s->sbm_imr); 1548 #endif 1549 1550 /* 1551 * Enable receiving unicasts and broadcasts 1552 */ 1553 1554 __raw_writeq(M_MAC_UCAST_EN | M_MAC_BCAST_EN, s->sbm_rxfilter); 1555 1556 /* 1557 * we're running now. 1558 */ 1559 1560 s->sbm_state = sbmac_state_on; 1561 1562 /* 1563 * Program multicast addresses 1564 */ 1565 1566 sbmac_setmulti(s); 1567 1568 /* 1569 * If channel was in promiscuous mode before, turn that on 1570 */ 1571 1572 if (s->sbm_devflags & IFF_PROMISC) { 1573 sbmac_promiscuous_mode(s,1); 1574 } 1575 1576 } 1577 1578 1579 /********************************************************************** 1580 * SBMAC_CHANNEL_STOP(s) 1581 * 1582 * Stop packet processing on this MAC. 1583 * 1584 * Input parameters: 1585 * s - sbmac structure 1586 * 1587 * Return value: 1588 * nothing 1589 ********************************************************************* */ 1590 1591 static void sbmac_channel_stop(struct sbmac_softc *s) 1592 { 1593 /* don't do this if already stopped */ 1594 1595 if (s->sbm_state == sbmac_state_off) 1596 return; 1597 1598 /* don't accept any packets, disable all interrupts */ 1599 1600 __raw_writeq(0, s->sbm_rxfilter); 1601 __raw_writeq(0, s->sbm_imr); 1602 1603 /* Turn off ticker */ 1604 1605 /* XXX */ 1606 1607 /* turn off receiver and transmitter */ 1608 1609 __raw_writeq(0, s->sbm_macenable); 1610 1611 /* We're stopped now. */ 1612 1613 s->sbm_state = sbmac_state_off; 1614 1615 /* 1616 * Stop DMA channels (rings should be ok now) 1617 */ 1618 1619 sbdma_channel_stop(&(s->sbm_rxdma)); 1620 sbdma_channel_stop(&(s->sbm_txdma)); 1621 1622 /* Empty the receive and transmit rings */ 1623 1624 sbdma_emptyring(&(s->sbm_rxdma)); 1625 sbdma_emptyring(&(s->sbm_txdma)); 1626 1627 } 1628 1629 /********************************************************************** 1630 * SBMAC_SET_CHANNEL_STATE(state) 1631 * 1632 * Set the channel's state ON or OFF 1633 * 1634 * Input parameters: 1635 * state - new state 1636 * 1637 * Return value: 1638 * old state 1639 ********************************************************************* */ 1640 static enum sbmac_state sbmac_set_channel_state(struct sbmac_softc *sc, 1641 enum sbmac_state state) 1642 { 1643 enum sbmac_state oldstate = sc->sbm_state; 1644 1645 /* 1646 * If same as previous state, return 1647 */ 1648 1649 if (state == oldstate) { 1650 return oldstate; 1651 } 1652 1653 /* 1654 * If new state is ON, turn channel on 1655 */ 1656 1657 if (state == sbmac_state_on) { 1658 sbmac_channel_start(sc); 1659 } 1660 else { 1661 sbmac_channel_stop(sc); 1662 } 1663 1664 /* 1665 * Return previous state 1666 */ 1667 1668 return oldstate; 1669 } 1670 1671 1672 /********************************************************************** 1673 * SBMAC_PROMISCUOUS_MODE(sc,onoff) 1674 * 1675 * Turn on or off promiscuous mode 1676 * 1677 * Input parameters: 1678 * sc - softc 1679 * onoff - 1 to turn on, 0 to turn off 1680 * 1681 * Return value: 1682 * nothing 1683 ********************************************************************* */ 1684 1685 static void sbmac_promiscuous_mode(struct sbmac_softc *sc,int onoff) 1686 { 1687 uint64_t reg; 1688 1689 if (sc->sbm_state != sbmac_state_on) 1690 return; 1691 1692 if (onoff) { 1693 reg = __raw_readq(sc->sbm_rxfilter); 1694 reg |= M_MAC_ALLPKT_EN; 1695 __raw_writeq(reg, sc->sbm_rxfilter); 1696 } 1697 else { 1698 reg = __raw_readq(sc->sbm_rxfilter); 1699 reg &= ~M_MAC_ALLPKT_EN; 1700 __raw_writeq(reg, sc->sbm_rxfilter); 1701 } 1702 } 1703 1704 /********************************************************************** 1705 * SBMAC_SETIPHDR_OFFSET(sc,onoff) 1706 * 1707 * Set the iphdr offset as 15 assuming ethernet encapsulation 1708 * 1709 * Input parameters: 1710 * sc - softc 1711 * 1712 * Return value: 1713 * nothing 1714 ********************************************************************* */ 1715 1716 static void sbmac_set_iphdr_offset(struct sbmac_softc *sc) 1717 { 1718 uint64_t reg; 1719 1720 /* Hard code the off set to 15 for now */ 1721 reg = __raw_readq(sc->sbm_rxfilter); 1722 reg &= ~M_MAC_IPHDR_OFFSET | V_MAC_IPHDR_OFFSET(15); 1723 __raw_writeq(reg, sc->sbm_rxfilter); 1724 1725 /* BCM1250 pass1 didn't have hardware checksum. Everything 1726 later does. */ 1727 if (soc_type == K_SYS_SOC_TYPE_BCM1250 && periph_rev < 2) { 1728 sc->rx_hw_checksum = DISABLE; 1729 } else { 1730 sc->rx_hw_checksum = ENABLE; 1731 } 1732 } 1733 1734 1735 /********************************************************************** 1736 * SBMAC_ADDR2REG(ptr) 1737 * 1738 * Convert six bytes into the 64-bit register value that 1739 * we typically write into the SBMAC's address/mcast registers 1740 * 1741 * Input parameters: 1742 * ptr - pointer to 6 bytes 1743 * 1744 * Return value: 1745 * register value 1746 ********************************************************************* */ 1747 1748 static uint64_t sbmac_addr2reg(unsigned char *ptr) 1749 { 1750 uint64_t reg = 0; 1751 1752 ptr += 6; 1753 1754 reg |= (uint64_t) *(--ptr); 1755 reg <<= 8; 1756 reg |= (uint64_t) *(--ptr); 1757 reg <<= 8; 1758 reg |= (uint64_t) *(--ptr); 1759 reg <<= 8; 1760 reg |= (uint64_t) *(--ptr); 1761 reg <<= 8; 1762 reg |= (uint64_t) *(--ptr); 1763 reg <<= 8; 1764 reg |= (uint64_t) *(--ptr); 1765 1766 return reg; 1767 } 1768 1769 1770 /********************************************************************** 1771 * SBMAC_SET_SPEED(s,speed) 1772 * 1773 * Configure LAN speed for the specified MAC. 1774 * Warning: must be called when MAC is off! 1775 * 1776 * Input parameters: 1777 * s - sbmac structure 1778 * speed - speed to set MAC to (see enum sbmac_speed) 1779 * 1780 * Return value: 1781 * 1 if successful 1782 * 0 indicates invalid parameters 1783 ********************************************************************* */ 1784 1785 static int sbmac_set_speed(struct sbmac_softc *s, enum sbmac_speed speed) 1786 { 1787 uint64_t cfg; 1788 uint64_t framecfg; 1789 1790 /* 1791 * Save new current values 1792 */ 1793 1794 s->sbm_speed = speed; 1795 1796 if (s->sbm_state == sbmac_state_on) 1797 return 0; /* save for next restart */ 1798 1799 /* 1800 * Read current register values 1801 */ 1802 1803 cfg = __raw_readq(s->sbm_maccfg); 1804 framecfg = __raw_readq(s->sbm_framecfg); 1805 1806 /* 1807 * Mask out the stuff we want to change 1808 */ 1809 1810 cfg &= ~(M_MAC_BURST_EN | M_MAC_SPEED_SEL); 1811 framecfg &= ~(M_MAC_IFG_RX | M_MAC_IFG_TX | M_MAC_IFG_THRSH | 1812 M_MAC_SLOT_SIZE); 1813 1814 /* 1815 * Now add in the new bits 1816 */ 1817 1818 switch (speed) { 1819 case sbmac_speed_10: 1820 framecfg |= V_MAC_IFG_RX_10 | 1821 V_MAC_IFG_TX_10 | 1822 K_MAC_IFG_THRSH_10 | 1823 V_MAC_SLOT_SIZE_10; 1824 cfg |= V_MAC_SPEED_SEL_10MBPS; 1825 break; 1826 1827 case sbmac_speed_100: 1828 framecfg |= V_MAC_IFG_RX_100 | 1829 V_MAC_IFG_TX_100 | 1830 V_MAC_IFG_THRSH_100 | 1831 V_MAC_SLOT_SIZE_100; 1832 cfg |= V_MAC_SPEED_SEL_100MBPS ; 1833 break; 1834 1835 case sbmac_speed_1000: 1836 framecfg |= V_MAC_IFG_RX_1000 | 1837 V_MAC_IFG_TX_1000 | 1838 V_MAC_IFG_THRSH_1000 | 1839 V_MAC_SLOT_SIZE_1000; 1840 cfg |= V_MAC_SPEED_SEL_1000MBPS | M_MAC_BURST_EN; 1841 break; 1842 1843 default: 1844 return 0; 1845 } 1846 1847 /* 1848 * Send the bits back to the hardware 1849 */ 1850 1851 __raw_writeq(framecfg, s->sbm_framecfg); 1852 __raw_writeq(cfg, s->sbm_maccfg); 1853 1854 return 1; 1855 } 1856 1857 /********************************************************************** 1858 * SBMAC_SET_DUPLEX(s,duplex,fc) 1859 * 1860 * Set Ethernet duplex and flow control options for this MAC 1861 * Warning: must be called when MAC is off! 1862 * 1863 * Input parameters: 1864 * s - sbmac structure 1865 * duplex - duplex setting (see enum sbmac_duplex) 1866 * fc - flow control setting (see enum sbmac_fc) 1867 * 1868 * Return value: 1869 * 1 if ok 1870 * 0 if an invalid parameter combination was specified 1871 ********************************************************************* */ 1872 1873 static int sbmac_set_duplex(struct sbmac_softc *s, enum sbmac_duplex duplex, 1874 enum sbmac_fc fc) 1875 { 1876 uint64_t cfg; 1877 1878 /* 1879 * Save new current values 1880 */ 1881 1882 s->sbm_duplex = duplex; 1883 s->sbm_fc = fc; 1884 1885 if (s->sbm_state == sbmac_state_on) 1886 return 0; /* save for next restart */ 1887 1888 /* 1889 * Read current register values 1890 */ 1891 1892 cfg = __raw_readq(s->sbm_maccfg); 1893 1894 /* 1895 * Mask off the stuff we're about to change 1896 */ 1897 1898 cfg &= ~(M_MAC_FC_SEL | M_MAC_FC_CMD | M_MAC_HDX_EN); 1899 1900 1901 switch (duplex) { 1902 case sbmac_duplex_half: 1903 switch (fc) { 1904 case sbmac_fc_disabled: 1905 cfg |= M_MAC_HDX_EN | V_MAC_FC_CMD_DISABLED; 1906 break; 1907 1908 case sbmac_fc_collision: 1909 cfg |= M_MAC_HDX_EN | V_MAC_FC_CMD_ENABLED; 1910 break; 1911 1912 case sbmac_fc_carrier: 1913 cfg |= M_MAC_HDX_EN | V_MAC_FC_CMD_ENAB_FALSECARR; 1914 break; 1915 1916 case sbmac_fc_frame: /* not valid in half duplex */ 1917 default: /* invalid selection */ 1918 return 0; 1919 } 1920 break; 1921 1922 case sbmac_duplex_full: 1923 switch (fc) { 1924 case sbmac_fc_disabled: 1925 cfg |= V_MAC_FC_CMD_DISABLED; 1926 break; 1927 1928 case sbmac_fc_frame: 1929 cfg |= V_MAC_FC_CMD_ENABLED; 1930 break; 1931 1932 case sbmac_fc_collision: /* not valid in full duplex */ 1933 case sbmac_fc_carrier: /* not valid in full duplex */ 1934 default: 1935 return 0; 1936 } 1937 break; 1938 default: 1939 return 0; 1940 } 1941 1942 /* 1943 * Send the bits back to the hardware 1944 */ 1945 1946 __raw_writeq(cfg, s->sbm_maccfg); 1947 1948 return 1; 1949 } 1950 1951 1952 1953 1954 /********************************************************************** 1955 * SBMAC_INTR() 1956 * 1957 * Interrupt handler for MAC interrupts 1958 * 1959 * Input parameters: 1960 * MAC structure 1961 * 1962 * Return value: 1963 * nothing 1964 ********************************************************************* */ 1965 static irqreturn_t sbmac_intr(int irq,void *dev_instance) 1966 { 1967 struct net_device *dev = (struct net_device *) dev_instance; 1968 struct sbmac_softc *sc = netdev_priv(dev); 1969 uint64_t isr; 1970 int handled = 0; 1971 1972 /* 1973 * Read the ISR (this clears the bits in the real 1974 * register, except for counter addr) 1975 */ 1976 1977 isr = __raw_readq(sc->sbm_isr) & ~M_MAC_COUNTER_ADDR; 1978 1979 if (isr == 0) 1980 return IRQ_RETVAL(0); 1981 handled = 1; 1982 1983 /* 1984 * Transmits on channel 0 1985 */ 1986 1987 if (isr & (M_MAC_INT_CHANNEL << S_MAC_TX_CH0)) 1988 sbdma_tx_process(sc,&(sc->sbm_txdma), 0); 1989 1990 if (isr & (M_MAC_INT_CHANNEL << S_MAC_RX_CH0)) { 1991 if (napi_schedule_prep(&sc->napi)) { 1992 __raw_writeq(0, sc->sbm_imr); 1993 __napi_schedule(&sc->napi); 1994 /* Depend on the exit from poll to reenable intr */ 1995 } 1996 else { 1997 /* may leave some packets behind */ 1998 sbdma_rx_process(sc,&(sc->sbm_rxdma), 1999 SBMAC_MAX_RXDESCR * 2, 0); 2000 } 2001 } 2002 return IRQ_RETVAL(handled); 2003 } 2004 2005 /********************************************************************** 2006 * SBMAC_START_TX(skb,dev) 2007 * 2008 * Start output on the specified interface. Basically, we 2009 * queue as many buffers as we can until the ring fills up, or 2010 * we run off the end of the queue, whichever comes first. 2011 * 2012 * Input parameters: 2013 * 2014 * 2015 * Return value: 2016 * nothing 2017 ********************************************************************* */ 2018 static netdev_tx_t sbmac_start_tx(struct sk_buff *skb, struct net_device *dev) 2019 { 2020 struct sbmac_softc *sc = netdev_priv(dev); 2021 unsigned long flags; 2022 2023 /* lock eth irq */ 2024 spin_lock_irqsave(&sc->sbm_lock, flags); 2025 2026 /* 2027 * Put the buffer on the transmit ring. If we 2028 * don't have room, stop the queue. 2029 */ 2030 2031 if (sbdma_add_txbuffer(&(sc->sbm_txdma),skb)) { 2032 /* XXX save skb that we could not send */ 2033 netif_stop_queue(dev); 2034 spin_unlock_irqrestore(&sc->sbm_lock, flags); 2035 2036 return NETDEV_TX_BUSY; 2037 } 2038 2039 spin_unlock_irqrestore(&sc->sbm_lock, flags); 2040 2041 return NETDEV_TX_OK; 2042 } 2043 2044 /********************************************************************** 2045 * SBMAC_SETMULTI(sc) 2046 * 2047 * Reprogram the multicast table into the hardware, given 2048 * the list of multicasts associated with the interface 2049 * structure. 2050 * 2051 * Input parameters: 2052 * sc - softc 2053 * 2054 * Return value: 2055 * nothing 2056 ********************************************************************* */ 2057 2058 static void sbmac_setmulti(struct sbmac_softc *sc) 2059 { 2060 uint64_t reg; 2061 void __iomem *port; 2062 int idx; 2063 struct netdev_hw_addr *ha; 2064 struct net_device *dev = sc->sbm_dev; 2065 2066 /* 2067 * Clear out entire multicast table. We do this by nuking 2068 * the entire hash table and all the direct matches except 2069 * the first one, which is used for our station address 2070 */ 2071 2072 for (idx = 1; idx < MAC_ADDR_COUNT; idx++) { 2073 port = sc->sbm_base + R_MAC_ADDR_BASE+(idx*sizeof(uint64_t)); 2074 __raw_writeq(0, port); 2075 } 2076 2077 for (idx = 0; idx < MAC_HASH_COUNT; idx++) { 2078 port = sc->sbm_base + R_MAC_HASH_BASE+(idx*sizeof(uint64_t)); 2079 __raw_writeq(0, port); 2080 } 2081 2082 /* 2083 * Clear the filter to say we don't want any multicasts. 2084 */ 2085 2086 reg = __raw_readq(sc->sbm_rxfilter); 2087 reg &= ~(M_MAC_MCAST_INV | M_MAC_MCAST_EN); 2088 __raw_writeq(reg, sc->sbm_rxfilter); 2089 2090 if (dev->flags & IFF_ALLMULTI) { 2091 /* 2092 * Enable ALL multicasts. Do this by inverting the 2093 * multicast enable bit. 2094 */ 2095 reg = __raw_readq(sc->sbm_rxfilter); 2096 reg |= (M_MAC_MCAST_INV | M_MAC_MCAST_EN); 2097 __raw_writeq(reg, sc->sbm_rxfilter); 2098 return; 2099 } 2100 2101 2102 /* 2103 * Progam new multicast entries. For now, only use the 2104 * perfect filter. In the future we'll need to use the 2105 * hash filter if the perfect filter overflows 2106 */ 2107 2108 /* XXX only using perfect filter for now, need to use hash 2109 * XXX if the table overflows */ 2110 2111 idx = 1; /* skip station address */ 2112 netdev_for_each_mc_addr(ha, dev) { 2113 if (idx == MAC_ADDR_COUNT) 2114 break; 2115 reg = sbmac_addr2reg(ha->addr); 2116 port = sc->sbm_base + R_MAC_ADDR_BASE+(idx * sizeof(uint64_t)); 2117 __raw_writeq(reg, port); 2118 idx++; 2119 } 2120 2121 /* 2122 * Enable the "accept multicast bits" if we programmed at least one 2123 * multicast. 2124 */ 2125 2126 if (idx > 1) { 2127 reg = __raw_readq(sc->sbm_rxfilter); 2128 reg |= M_MAC_MCAST_EN; 2129 __raw_writeq(reg, sc->sbm_rxfilter); 2130 } 2131 } 2132 2133 static const struct net_device_ops sbmac_netdev_ops = { 2134 .ndo_open = sbmac_open, 2135 .ndo_stop = sbmac_close, 2136 .ndo_start_xmit = sbmac_start_tx, 2137 .ndo_set_rx_mode = sbmac_set_rx_mode, 2138 .ndo_tx_timeout = sbmac_tx_timeout, 2139 .ndo_eth_ioctl = sbmac_mii_ioctl, 2140 .ndo_validate_addr = eth_validate_addr, 2141 .ndo_set_mac_address = eth_mac_addr, 2142 #ifdef CONFIG_NET_POLL_CONTROLLER 2143 .ndo_poll_controller = sbmac_netpoll, 2144 #endif 2145 }; 2146 2147 /********************************************************************** 2148 * SBMAC_INIT(dev) 2149 * 2150 * Attach routine - init hardware and hook ourselves into linux 2151 * 2152 * Input parameters: 2153 * dev - net_device structure 2154 * 2155 * Return value: 2156 * status 2157 ********************************************************************* */ 2158 2159 static int sbmac_init(struct platform_device *pldev, long long base) 2160 { 2161 struct net_device *dev = platform_get_drvdata(pldev); 2162 int idx = pldev->id; 2163 struct sbmac_softc *sc = netdev_priv(dev); 2164 unsigned char *eaddr; 2165 uint64_t ea_reg; 2166 int i; 2167 int err; 2168 2169 sc->sbm_dev = dev; 2170 sc->sbe_idx = idx; 2171 2172 eaddr = sc->sbm_hwaddr; 2173 2174 /* 2175 * Read the ethernet address. The firmware left this programmed 2176 * for us in the ethernet address register for each mac. 2177 */ 2178 2179 ea_reg = __raw_readq(sc->sbm_base + R_MAC_ETHERNET_ADDR); 2180 __raw_writeq(0, sc->sbm_base + R_MAC_ETHERNET_ADDR); 2181 for (i = 0; i < 6; i++) { 2182 eaddr[i] = (uint8_t) (ea_reg & 0xFF); 2183 ea_reg >>= 8; 2184 } 2185 2186 eth_hw_addr_set(dev, eaddr); 2187 2188 /* 2189 * Initialize context (get pointers to registers and stuff), then 2190 * allocate the memory for the descriptor tables. 2191 */ 2192 2193 sbmac_initctx(sc); 2194 2195 /* 2196 * Set up Linux device callins 2197 */ 2198 2199 spin_lock_init(&(sc->sbm_lock)); 2200 2201 dev->netdev_ops = &sbmac_netdev_ops; 2202 dev->watchdog_timeo = TX_TIMEOUT; 2203 dev->min_mtu = 0; 2204 dev->max_mtu = ENET_PACKET_SIZE; 2205 2206 netif_napi_add_weight(dev, &sc->napi, sbmac_poll, 16); 2207 2208 dev->irq = UNIT_INT(idx); 2209 2210 /* This is needed for PASS2 for Rx H/W checksum feature */ 2211 sbmac_set_iphdr_offset(sc); 2212 2213 sc->mii_bus = mdiobus_alloc(); 2214 if (sc->mii_bus == NULL) { 2215 err = -ENOMEM; 2216 goto uninit_ctx; 2217 } 2218 2219 sc->mii_bus->name = sbmac_mdio_string; 2220 snprintf(sc->mii_bus->id, MII_BUS_ID_SIZE, "%s-%x", 2221 pldev->name, idx); 2222 sc->mii_bus->priv = sc; 2223 sc->mii_bus->read = sbmac_mii_read; 2224 sc->mii_bus->write = sbmac_mii_write; 2225 2226 sc->mii_bus->parent = &pldev->dev; 2227 /* 2228 * Probe PHY address 2229 */ 2230 err = mdiobus_register(sc->mii_bus); 2231 if (err) { 2232 printk(KERN_ERR "%s: unable to register MDIO bus\n", 2233 dev->name); 2234 goto free_mdio; 2235 } 2236 platform_set_drvdata(pldev, sc->mii_bus); 2237 2238 err = register_netdev(dev); 2239 if (err) { 2240 printk(KERN_ERR "%s.%d: unable to register netdev\n", 2241 sbmac_string, idx); 2242 goto unreg_mdio; 2243 } 2244 2245 pr_info("%s.%d: registered as %s\n", sbmac_string, idx, dev->name); 2246 2247 if (sc->rx_hw_checksum == ENABLE) 2248 pr_info("%s: enabling TCP rcv checksum\n", dev->name); 2249 2250 /* 2251 * Display Ethernet address (this is called during the config 2252 * process so we need to finish off the config message that 2253 * was being displayed) 2254 */ 2255 pr_info("%s: SiByte Ethernet at 0x%08Lx, address: %pM\n", 2256 dev->name, base, eaddr); 2257 2258 return 0; 2259 unreg_mdio: 2260 mdiobus_unregister(sc->mii_bus); 2261 free_mdio: 2262 mdiobus_free(sc->mii_bus); 2263 uninit_ctx: 2264 sbmac_uninitctx(sc); 2265 return err; 2266 } 2267 2268 2269 static int sbmac_open(struct net_device *dev) 2270 { 2271 struct sbmac_softc *sc = netdev_priv(dev); 2272 int err; 2273 2274 if (debug > 1) 2275 pr_debug("%s: sbmac_open() irq %d.\n", dev->name, dev->irq); 2276 2277 /* 2278 * map/route interrupt (clear status first, in case something 2279 * weird is pending; we haven't initialized the mac registers 2280 * yet) 2281 */ 2282 2283 __raw_readq(sc->sbm_isr); 2284 err = request_irq(dev->irq, sbmac_intr, IRQF_SHARED, dev->name, dev); 2285 if (err) { 2286 printk(KERN_ERR "%s: unable to get IRQ %d\n", dev->name, 2287 dev->irq); 2288 goto out_err; 2289 } 2290 2291 sc->sbm_speed = sbmac_speed_none; 2292 sc->sbm_duplex = sbmac_duplex_none; 2293 sc->sbm_fc = sbmac_fc_none; 2294 sc->sbm_pause = -1; 2295 sc->sbm_link = 0; 2296 2297 /* 2298 * Attach to the PHY 2299 */ 2300 err = sbmac_mii_probe(dev); 2301 if (err) 2302 goto out_unregister; 2303 2304 /* 2305 * Turn on the channel 2306 */ 2307 2308 sbmac_set_channel_state(sc,sbmac_state_on); 2309 2310 netif_start_queue(dev); 2311 2312 sbmac_set_rx_mode(dev); 2313 2314 phy_start(sc->phy_dev); 2315 2316 napi_enable(&sc->napi); 2317 2318 return 0; 2319 2320 out_unregister: 2321 free_irq(dev->irq, dev); 2322 out_err: 2323 return err; 2324 } 2325 2326 static int sbmac_mii_probe(struct net_device *dev) 2327 { 2328 struct sbmac_softc *sc = netdev_priv(dev); 2329 struct phy_device *phy_dev; 2330 2331 phy_dev = phy_find_first(sc->mii_bus); 2332 if (!phy_dev) { 2333 printk(KERN_ERR "%s: no PHY found\n", dev->name); 2334 return -ENXIO; 2335 } 2336 2337 phy_dev = phy_connect(dev, dev_name(&phy_dev->mdio.dev), 2338 &sbmac_mii_poll, PHY_INTERFACE_MODE_GMII); 2339 if (IS_ERR(phy_dev)) { 2340 printk(KERN_ERR "%s: could not attach to PHY\n", dev->name); 2341 return PTR_ERR(phy_dev); 2342 } 2343 2344 /* Remove any features not supported by the controller */ 2345 phy_set_max_speed(phy_dev, SPEED_1000); 2346 phy_support_asym_pause(phy_dev); 2347 2348 phy_attached_info(phy_dev); 2349 2350 sc->phy_dev = phy_dev; 2351 2352 return 0; 2353 } 2354 2355 2356 static void sbmac_mii_poll(struct net_device *dev) 2357 { 2358 struct sbmac_softc *sc = netdev_priv(dev); 2359 struct phy_device *phy_dev = sc->phy_dev; 2360 unsigned long flags; 2361 enum sbmac_fc fc; 2362 int link_chg, speed_chg, duplex_chg, pause_chg, fc_chg; 2363 2364 link_chg = (sc->sbm_link != phy_dev->link); 2365 speed_chg = (sc->sbm_speed != phy_dev->speed); 2366 duplex_chg = (sc->sbm_duplex != phy_dev->duplex); 2367 pause_chg = (sc->sbm_pause != phy_dev->pause); 2368 2369 if (!link_chg && !speed_chg && !duplex_chg && !pause_chg) 2370 return; /* Hmmm... */ 2371 2372 if (!phy_dev->link) { 2373 if (link_chg) { 2374 sc->sbm_link = phy_dev->link; 2375 sc->sbm_speed = sbmac_speed_none; 2376 sc->sbm_duplex = sbmac_duplex_none; 2377 sc->sbm_fc = sbmac_fc_disabled; 2378 sc->sbm_pause = -1; 2379 pr_info("%s: link unavailable\n", dev->name); 2380 } 2381 return; 2382 } 2383 2384 if (phy_dev->duplex == DUPLEX_FULL) { 2385 if (phy_dev->pause) 2386 fc = sbmac_fc_frame; 2387 else 2388 fc = sbmac_fc_disabled; 2389 } else 2390 fc = sbmac_fc_collision; 2391 fc_chg = (sc->sbm_fc != fc); 2392 2393 pr_info("%s: link available: %dbase-%cD\n", dev->name, phy_dev->speed, 2394 phy_dev->duplex == DUPLEX_FULL ? 'F' : 'H'); 2395 2396 spin_lock_irqsave(&sc->sbm_lock, flags); 2397 2398 sc->sbm_speed = phy_dev->speed; 2399 sc->sbm_duplex = phy_dev->duplex; 2400 sc->sbm_fc = fc; 2401 sc->sbm_pause = phy_dev->pause; 2402 sc->sbm_link = phy_dev->link; 2403 2404 if ((speed_chg || duplex_chg || fc_chg) && 2405 sc->sbm_state != sbmac_state_off) { 2406 /* 2407 * something changed, restart the channel 2408 */ 2409 if (debug > 1) 2410 pr_debug("%s: restarting channel " 2411 "because PHY state changed\n", dev->name); 2412 sbmac_channel_stop(sc); 2413 sbmac_channel_start(sc); 2414 } 2415 2416 spin_unlock_irqrestore(&sc->sbm_lock, flags); 2417 } 2418 2419 2420 static void sbmac_tx_timeout (struct net_device *dev, unsigned int txqueue) 2421 { 2422 struct sbmac_softc *sc = netdev_priv(dev); 2423 unsigned long flags; 2424 2425 spin_lock_irqsave(&sc->sbm_lock, flags); 2426 2427 2428 netif_trans_update(dev); /* prevent tx timeout */ 2429 dev->stats.tx_errors++; 2430 2431 spin_unlock_irqrestore(&sc->sbm_lock, flags); 2432 2433 printk (KERN_WARNING "%s: Transmit timed out\n",dev->name); 2434 } 2435 2436 2437 2438 2439 static void sbmac_set_rx_mode(struct net_device *dev) 2440 { 2441 unsigned long flags; 2442 struct sbmac_softc *sc = netdev_priv(dev); 2443 2444 spin_lock_irqsave(&sc->sbm_lock, flags); 2445 if ((dev->flags ^ sc->sbm_devflags) & IFF_PROMISC) { 2446 /* 2447 * Promiscuous changed. 2448 */ 2449 2450 if (dev->flags & IFF_PROMISC) { 2451 sbmac_promiscuous_mode(sc,1); 2452 } 2453 else { 2454 sbmac_promiscuous_mode(sc,0); 2455 } 2456 } 2457 spin_unlock_irqrestore(&sc->sbm_lock, flags); 2458 2459 /* 2460 * Program the multicasts. Do this every time. 2461 */ 2462 2463 sbmac_setmulti(sc); 2464 2465 } 2466 2467 static int sbmac_mii_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) 2468 { 2469 struct sbmac_softc *sc = netdev_priv(dev); 2470 2471 if (!netif_running(dev) || !sc->phy_dev) 2472 return -EINVAL; 2473 2474 return phy_mii_ioctl(sc->phy_dev, rq, cmd); 2475 } 2476 2477 static int sbmac_close(struct net_device *dev) 2478 { 2479 struct sbmac_softc *sc = netdev_priv(dev); 2480 2481 napi_disable(&sc->napi); 2482 2483 phy_stop(sc->phy_dev); 2484 2485 sbmac_set_channel_state(sc, sbmac_state_off); 2486 2487 netif_stop_queue(dev); 2488 2489 if (debug > 1) 2490 pr_debug("%s: Shutting down ethercard\n", dev->name); 2491 2492 phy_disconnect(sc->phy_dev); 2493 sc->phy_dev = NULL; 2494 free_irq(dev->irq, dev); 2495 2496 sbdma_emptyring(&(sc->sbm_txdma)); 2497 sbdma_emptyring(&(sc->sbm_rxdma)); 2498 2499 return 0; 2500 } 2501 2502 static int sbmac_poll(struct napi_struct *napi, int budget) 2503 { 2504 struct sbmac_softc *sc = container_of(napi, struct sbmac_softc, napi); 2505 int work_done; 2506 2507 work_done = sbdma_rx_process(sc, &(sc->sbm_rxdma), budget, 1); 2508 sbdma_tx_process(sc, &(sc->sbm_txdma), 1); 2509 2510 if (work_done < budget) { 2511 napi_complete_done(napi, work_done); 2512 2513 #ifdef CONFIG_SBMAC_COALESCE 2514 __raw_writeq(((M_MAC_INT_EOP_COUNT | M_MAC_INT_EOP_TIMER) << S_MAC_TX_CH0) | 2515 ((M_MAC_INT_EOP_COUNT | M_MAC_INT_EOP_TIMER) << S_MAC_RX_CH0), 2516 sc->sbm_imr); 2517 #else 2518 __raw_writeq((M_MAC_INT_CHANNEL << S_MAC_TX_CH0) | 2519 (M_MAC_INT_CHANNEL << S_MAC_RX_CH0), sc->sbm_imr); 2520 #endif 2521 } 2522 2523 return work_done; 2524 } 2525 2526 2527 static int sbmac_probe(struct platform_device *pldev) 2528 { 2529 struct net_device *dev; 2530 struct sbmac_softc *sc; 2531 void __iomem *sbm_base; 2532 struct resource *res; 2533 u64 sbmac_orig_hwaddr; 2534 int err; 2535 2536 res = platform_get_resource(pldev, IORESOURCE_MEM, 0); 2537 if (!res) { 2538 printk(KERN_ERR "%s: failed to get resource\n", 2539 dev_name(&pldev->dev)); 2540 err = -EINVAL; 2541 goto out_out; 2542 } 2543 sbm_base = ioremap(res->start, resource_size(res)); 2544 if (!sbm_base) { 2545 printk(KERN_ERR "%s: unable to map device registers\n", 2546 dev_name(&pldev->dev)); 2547 err = -ENOMEM; 2548 goto out_out; 2549 } 2550 2551 /* 2552 * The R_MAC_ETHERNET_ADDR register will be set to some nonzero 2553 * value for us by the firmware if we're going to use this MAC. 2554 * If we find a zero, skip this MAC. 2555 */ 2556 sbmac_orig_hwaddr = __raw_readq(sbm_base + R_MAC_ETHERNET_ADDR); 2557 pr_debug("%s: %sconfiguring MAC at 0x%08Lx\n", dev_name(&pldev->dev), 2558 sbmac_orig_hwaddr ? "" : "not ", (long long)res->start); 2559 if (sbmac_orig_hwaddr == 0) { 2560 err = 0; 2561 goto out_unmap; 2562 } 2563 2564 /* 2565 * Okay, cool. Initialize this MAC. 2566 */ 2567 dev = alloc_etherdev(sizeof(struct sbmac_softc)); 2568 if (!dev) { 2569 err = -ENOMEM; 2570 goto out_unmap; 2571 } 2572 2573 platform_set_drvdata(pldev, dev); 2574 SET_NETDEV_DEV(dev, &pldev->dev); 2575 2576 sc = netdev_priv(dev); 2577 sc->sbm_base = sbm_base; 2578 2579 err = sbmac_init(pldev, res->start); 2580 if (err) 2581 goto out_kfree; 2582 2583 return 0; 2584 2585 out_kfree: 2586 free_netdev(dev); 2587 __raw_writeq(sbmac_orig_hwaddr, sbm_base + R_MAC_ETHERNET_ADDR); 2588 2589 out_unmap: 2590 iounmap(sbm_base); 2591 2592 out_out: 2593 return err; 2594 } 2595 2596 static int sbmac_remove(struct platform_device *pldev) 2597 { 2598 struct net_device *dev = platform_get_drvdata(pldev); 2599 struct sbmac_softc *sc = netdev_priv(dev); 2600 2601 unregister_netdev(dev); 2602 sbmac_uninitctx(sc); 2603 mdiobus_unregister(sc->mii_bus); 2604 mdiobus_free(sc->mii_bus); 2605 iounmap(sc->sbm_base); 2606 free_netdev(dev); 2607 2608 return 0; 2609 } 2610 2611 static struct platform_driver sbmac_driver = { 2612 .probe = sbmac_probe, 2613 .remove = sbmac_remove, 2614 .driver = { 2615 .name = sbmac_string, 2616 }, 2617 }; 2618 2619 module_platform_driver(sbmac_driver); 2620 MODULE_LICENSE("GPL"); 2621