1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Broadcom GENET MDIO routines 4 * 5 * Copyright (c) 2014-2017 Broadcom 6 */ 7 8 #include <linux/acpi.h> 9 #include <linux/types.h> 10 #include <linux/delay.h> 11 #include <linux/wait.h> 12 #include <linux/mii.h> 13 #include <linux/ethtool.h> 14 #include <linux/bitops.h> 15 #include <linux/netdevice.h> 16 #include <linux/platform_device.h> 17 #include <linux/phy.h> 18 #include <linux/phy_fixed.h> 19 #include <linux/brcmphy.h> 20 #include <linux/of.h> 21 #include <linux/of_net.h> 22 #include <linux/of_mdio.h> 23 #include <linux/platform_data/bcmgenet.h> 24 #include <linux/platform_data/mdio-bcm-unimac.h> 25 26 #include "bcmgenet.h" 27 28 static void bcmgenet_mac_config(struct net_device *dev) 29 { 30 struct bcmgenet_priv *priv = netdev_priv(dev); 31 struct phy_device *phydev = dev->phydev; 32 u32 reg, cmd_bits = 0; 33 bool active; 34 35 /* speed */ 36 if (phydev->speed == SPEED_1000) 37 cmd_bits = CMD_SPEED_1000; 38 else if (phydev->speed == SPEED_100) 39 cmd_bits = CMD_SPEED_100; 40 else 41 cmd_bits = CMD_SPEED_10; 42 cmd_bits <<= CMD_SPEED_SHIFT; 43 44 /* duplex */ 45 if (phydev->duplex != DUPLEX_FULL) { 46 cmd_bits |= CMD_HD_EN | 47 CMD_RX_PAUSE_IGNORE | CMD_TX_PAUSE_IGNORE; 48 } else { 49 /* pause capability defaults to Symmetric */ 50 if (priv->autoneg_pause) { 51 bool tx_pause = 0, rx_pause = 0; 52 53 if (phydev->autoneg) 54 phy_get_pause(phydev, &tx_pause, &rx_pause); 55 56 if (!tx_pause) 57 cmd_bits |= CMD_TX_PAUSE_IGNORE; 58 if (!rx_pause) 59 cmd_bits |= CMD_RX_PAUSE_IGNORE; 60 } 61 62 /* Manual override */ 63 if (!priv->rx_pause) 64 cmd_bits |= CMD_RX_PAUSE_IGNORE; 65 if (!priv->tx_pause) 66 cmd_bits |= CMD_TX_PAUSE_IGNORE; 67 } 68 69 /* Program UMAC and RGMII block based on established 70 * link speed, duplex, and pause. The speed set in 71 * umac->cmd tell RGMII block which clock to use for 72 * transmit -- 25MHz(100Mbps) or 125MHz(1Gbps). 73 * Receive clock is provided by the PHY. 74 */ 75 reg = bcmgenet_ext_readl(priv, EXT_RGMII_OOB_CTRL); 76 reg |= RGMII_LINK; 77 bcmgenet_ext_writel(priv, reg, EXT_RGMII_OOB_CTRL); 78 79 reg = bcmgenet_umac_readl(priv, UMAC_CMD); 80 reg &= ~((CMD_SPEED_MASK << CMD_SPEED_SHIFT) | 81 CMD_HD_EN | 82 CMD_RX_PAUSE_IGNORE | CMD_TX_PAUSE_IGNORE); 83 reg |= cmd_bits; 84 if (reg & CMD_SW_RESET) { 85 reg &= ~CMD_SW_RESET; 86 bcmgenet_umac_writel(priv, reg, UMAC_CMD); 87 udelay(2); 88 reg |= CMD_TX_EN | CMD_RX_EN; 89 } 90 bcmgenet_umac_writel(priv, reg, UMAC_CMD); 91 92 active = phy_init_eee(phydev, 0) >= 0; 93 bcmgenet_eee_enable_set(dev, 94 priv->eee.eee_enabled && active, 95 priv->eee.tx_lpi_enabled); 96 } 97 98 /* setup netdev link state when PHY link status change and 99 * update UMAC and RGMII block when link up 100 */ 101 void bcmgenet_mii_setup(struct net_device *dev) 102 { 103 struct bcmgenet_priv *priv = netdev_priv(dev); 104 struct phy_device *phydev = dev->phydev; 105 u32 reg; 106 107 if (phydev->link) { 108 bcmgenet_mac_config(dev); 109 } else { 110 reg = bcmgenet_ext_readl(priv, EXT_RGMII_OOB_CTRL); 111 reg &= ~RGMII_LINK; 112 bcmgenet_ext_writel(priv, reg, EXT_RGMII_OOB_CTRL); 113 } 114 115 phy_print_status(phydev); 116 } 117 118 119 static int bcmgenet_fixed_phy_link_update(struct net_device *dev, 120 struct fixed_phy_status *status) 121 { 122 struct bcmgenet_priv *priv; 123 u32 reg; 124 125 if (dev && dev->phydev && status) { 126 priv = netdev_priv(dev); 127 reg = bcmgenet_umac_readl(priv, UMAC_MODE); 128 status->link = !!(reg & MODE_LINK_STATUS); 129 } 130 131 return 0; 132 } 133 134 void bcmgenet_phy_pause_set(struct net_device *dev, bool rx, bool tx) 135 { 136 struct phy_device *phydev = dev->phydev; 137 138 linkmode_mod_bit(ETHTOOL_LINK_MODE_Pause_BIT, phydev->advertising, rx); 139 linkmode_mod_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, phydev->advertising, 140 rx | tx); 141 phy_start_aneg(phydev); 142 143 mutex_lock(&phydev->lock); 144 if (phydev->link) 145 bcmgenet_mac_config(dev); 146 mutex_unlock(&phydev->lock); 147 } 148 149 void bcmgenet_phy_power_set(struct net_device *dev, bool enable) 150 { 151 struct bcmgenet_priv *priv = netdev_priv(dev); 152 u32 reg = 0; 153 154 /* EXT_GPHY_CTRL is only valid for GENETv4 and onward */ 155 if (GENET_IS_V4(priv) || priv->ephy_16nm) { 156 reg = bcmgenet_ext_readl(priv, EXT_GPHY_CTRL); 157 if (enable) { 158 reg &= ~EXT_CK25_DIS; 159 bcmgenet_ext_writel(priv, reg, EXT_GPHY_CTRL); 160 mdelay(1); 161 162 reg &= ~(EXT_CFG_IDDQ_BIAS | EXT_CFG_PWR_DOWN | 163 EXT_CFG_IDDQ_GLOBAL_PWR); 164 reg |= EXT_GPHY_RESET; 165 bcmgenet_ext_writel(priv, reg, EXT_GPHY_CTRL); 166 mdelay(1); 167 168 reg &= ~EXT_GPHY_RESET; 169 } else { 170 reg |= EXT_CFG_IDDQ_BIAS | EXT_CFG_PWR_DOWN | 171 EXT_GPHY_RESET | EXT_CFG_IDDQ_GLOBAL_PWR; 172 bcmgenet_ext_writel(priv, reg, EXT_GPHY_CTRL); 173 mdelay(1); 174 reg |= EXT_CK25_DIS; 175 } 176 bcmgenet_ext_writel(priv, reg, EXT_GPHY_CTRL); 177 udelay(60); 178 } else { 179 mdelay(1); 180 } 181 } 182 183 static void bcmgenet_moca_phy_setup(struct bcmgenet_priv *priv) 184 { 185 if (priv->hw_params->flags & GENET_HAS_MOCA_LINK_DET) 186 fixed_phy_set_link_update(priv->dev->phydev, 187 bcmgenet_fixed_phy_link_update); 188 } 189 190 int bcmgenet_mii_config(struct net_device *dev, bool init) 191 { 192 struct bcmgenet_priv *priv = netdev_priv(dev); 193 struct phy_device *phydev = dev->phydev; 194 struct device *kdev = &priv->pdev->dev; 195 const char *phy_name = NULL; 196 u32 id_mode_dis = 0; 197 u32 port_ctrl; 198 u32 reg; 199 200 switch (priv->phy_interface) { 201 case PHY_INTERFACE_MODE_INTERNAL: 202 phy_name = "internal PHY"; 203 fallthrough; 204 case PHY_INTERFACE_MODE_MOCA: 205 /* Irrespective of the actually configured PHY speed (100 or 206 * 1000) GENETv4 only has an internal GPHY so we will just end 207 * up masking the Gigabit features from what we support, not 208 * switching to the EPHY 209 */ 210 if (GENET_IS_V4(priv)) 211 port_ctrl = PORT_MODE_INT_GPHY; 212 else 213 port_ctrl = PORT_MODE_INT_EPHY; 214 215 if (!phy_name) { 216 phy_name = "MoCA"; 217 if (!GENET_IS_V5(priv)) 218 port_ctrl |= LED_ACT_SOURCE_MAC; 219 bcmgenet_moca_phy_setup(priv); 220 } 221 break; 222 223 case PHY_INTERFACE_MODE_MII: 224 phy_name = "external MII"; 225 phy_set_max_speed(phydev, SPEED_100); 226 port_ctrl = PORT_MODE_EXT_EPHY; 227 break; 228 229 case PHY_INTERFACE_MODE_REVMII: 230 phy_name = "external RvMII"; 231 /* of_mdiobus_register took care of reading the 'max-speed' 232 * PHY property for us, effectively limiting the PHY supported 233 * capabilities, use that knowledge to also configure the 234 * Reverse MII interface correctly. 235 */ 236 if (linkmode_test_bit(ETHTOOL_LINK_MODE_1000baseT_Full_BIT, 237 dev->phydev->supported)) 238 port_ctrl = PORT_MODE_EXT_RVMII_50; 239 else 240 port_ctrl = PORT_MODE_EXT_RVMII_25; 241 break; 242 243 case PHY_INTERFACE_MODE_RGMII: 244 /* RGMII_NO_ID: TXC transitions at the same time as TXD 245 * (requires PCB or receiver-side delay) 246 * 247 * ID is implicitly disabled for 100Mbps (RG)MII operation. 248 */ 249 phy_name = "external RGMII (no delay)"; 250 id_mode_dis = BIT(16); 251 port_ctrl = PORT_MODE_EXT_GPHY; 252 break; 253 254 case PHY_INTERFACE_MODE_RGMII_TXID: 255 /* RGMII_TXID: Add 2ns delay on TXC (90 degree shift) */ 256 phy_name = "external RGMII (TX delay)"; 257 port_ctrl = PORT_MODE_EXT_GPHY; 258 break; 259 260 case PHY_INTERFACE_MODE_RGMII_RXID: 261 phy_name = "external RGMII (RX delay)"; 262 port_ctrl = PORT_MODE_EXT_GPHY; 263 break; 264 default: 265 dev_err(kdev, "unknown phy mode: %d\n", priv->phy_interface); 266 return -EINVAL; 267 } 268 269 bcmgenet_sys_writel(priv, port_ctrl, SYS_PORT_CTRL); 270 271 priv->ext_phy = !priv->internal_phy && 272 (priv->phy_interface != PHY_INTERFACE_MODE_MOCA); 273 274 /* This is an external PHY (xMII), so we need to enable the RGMII 275 * block for the interface to work, unconditionally clear the 276 * Out-of-band disable since we do not need it. 277 */ 278 reg = bcmgenet_ext_readl(priv, EXT_RGMII_OOB_CTRL); 279 reg &= ~OOB_DISABLE; 280 if (priv->ext_phy) { 281 reg &= ~ID_MODE_DIS; 282 reg |= id_mode_dis; 283 if (GENET_IS_V1(priv) || GENET_IS_V2(priv) || GENET_IS_V3(priv)) 284 reg |= RGMII_MODE_EN_V123; 285 else 286 reg |= RGMII_MODE_EN; 287 } 288 bcmgenet_ext_writel(priv, reg, EXT_RGMII_OOB_CTRL); 289 290 if (init) 291 dev_info(kdev, "configuring instance for %s\n", phy_name); 292 293 return 0; 294 } 295 296 int bcmgenet_mii_probe(struct net_device *dev) 297 { 298 struct bcmgenet_priv *priv = netdev_priv(dev); 299 struct device *kdev = &priv->pdev->dev; 300 struct device_node *dn = kdev->of_node; 301 phy_interface_t phy_iface = priv->phy_interface; 302 struct phy_device *phydev; 303 u32 phy_flags = PHY_BRCM_AUTO_PWRDWN_ENABLE | 304 PHY_BRCM_DIS_TXCRXC_NOENRGY | 305 PHY_BRCM_IDDQ_SUSPEND; 306 int ret; 307 308 /* Communicate the integrated PHY revision */ 309 if (priv->internal_phy) 310 phy_flags = priv->gphy_rev; 311 312 /* This is an ugly quirk but we have not been correctly interpreting 313 * the phy_interface values and we have done that across different 314 * drivers, so at least we are consistent in our mistakes. 315 * 316 * When the Generic PHY driver is in use either the PHY has been 317 * strapped or programmed correctly by the boot loader so we should 318 * stick to our incorrect interpretation since we have validated it. 319 * 320 * Now when a dedicated PHY driver is in use, we need to reverse the 321 * meaning of the phy_interface_mode values to something that the PHY 322 * driver will interpret and act on such that we have two mistakes 323 * canceling themselves so to speak. We only do this for the two 324 * modes that GENET driver officially supports on Broadcom STB chips: 325 * PHY_INTERFACE_MODE_RGMII and PHY_INTERFACE_MODE_RGMII_TXID. Other 326 * modes are not *officially* supported with the boot loader and the 327 * scripted environment generating Device Tree blobs for those 328 * platforms. 329 * 330 * Note that internal PHY, MoCA and fixed-link configurations are not 331 * affected because they use different phy_interface_t values or the 332 * Generic PHY driver. 333 */ 334 switch (priv->phy_interface) { 335 case PHY_INTERFACE_MODE_RGMII: 336 phy_iface = PHY_INTERFACE_MODE_RGMII_ID; 337 break; 338 case PHY_INTERFACE_MODE_RGMII_TXID: 339 phy_iface = PHY_INTERFACE_MODE_RGMII_RXID; 340 break; 341 default: 342 break; 343 } 344 345 if (dn) { 346 phydev = of_phy_connect(dev, priv->phy_dn, bcmgenet_mii_setup, 347 phy_flags, phy_iface); 348 if (!phydev) { 349 pr_err("could not attach to PHY\n"); 350 return -ENODEV; 351 } 352 } else { 353 if (has_acpi_companion(kdev)) { 354 char mdio_bus_id[MII_BUS_ID_SIZE]; 355 struct mii_bus *unimacbus; 356 357 snprintf(mdio_bus_id, MII_BUS_ID_SIZE, "%s-%d", 358 UNIMAC_MDIO_DRV_NAME, priv->pdev->id); 359 360 unimacbus = mdio_find_bus(mdio_bus_id); 361 if (!unimacbus) { 362 pr_err("Unable to find mii\n"); 363 return -ENODEV; 364 } 365 phydev = phy_find_first(unimacbus); 366 put_device(&unimacbus->dev); 367 if (!phydev) { 368 pr_err("Unable to find PHY\n"); 369 return -ENODEV; 370 } 371 } else { 372 phydev = dev->phydev; 373 } 374 phydev->dev_flags = phy_flags; 375 376 ret = phy_connect_direct(dev, phydev, bcmgenet_mii_setup, 377 phy_iface); 378 if (ret) { 379 pr_err("could not attach to PHY\n"); 380 return -ENODEV; 381 } 382 } 383 384 /* Configure port multiplexer based on what the probed PHY device since 385 * reading the 'max-speed' property determines the maximum supported 386 * PHY speed which is needed for bcmgenet_mii_config() to configure 387 * things appropriately. 388 */ 389 ret = bcmgenet_mii_config(dev, true); 390 if (ret) { 391 phy_disconnect(dev->phydev); 392 return ret; 393 } 394 395 /* The internal PHY has its link interrupts routed to the 396 * Ethernet MAC ISRs. On GENETv5 there is a hardware issue 397 * that prevents the signaling of link UP interrupts when 398 * the link operates at 10Mbps, so fallback to polling for 399 * those versions of GENET. 400 */ 401 if (priv->internal_phy && !GENET_IS_V5(priv)) 402 dev->phydev->irq = PHY_MAC_INTERRUPT; 403 404 /* Indicate that the MAC is responsible for PHY PM */ 405 dev->phydev->mac_managed_pm = true; 406 407 return 0; 408 } 409 410 static struct device_node *bcmgenet_mii_of_find_mdio(struct bcmgenet_priv *priv) 411 { 412 struct device_node *dn = priv->pdev->dev.of_node; 413 struct device *kdev = &priv->pdev->dev; 414 char *compat; 415 416 compat = kasprintf(GFP_KERNEL, "brcm,genet-mdio-v%d", priv->version); 417 if (!compat) 418 return NULL; 419 420 priv->mdio_dn = of_get_compatible_child(dn, compat); 421 kfree(compat); 422 if (!priv->mdio_dn) { 423 dev_err(kdev, "unable to find MDIO bus node\n"); 424 return NULL; 425 } 426 427 return priv->mdio_dn; 428 } 429 430 static void bcmgenet_mii_pdata_init(struct bcmgenet_priv *priv, 431 struct unimac_mdio_pdata *ppd) 432 { 433 struct device *kdev = &priv->pdev->dev; 434 struct bcmgenet_platform_data *pd = kdev->platform_data; 435 436 if (pd->phy_interface != PHY_INTERFACE_MODE_MOCA && pd->mdio_enabled) { 437 /* 438 * Internal or external PHY with MDIO access 439 */ 440 if (pd->phy_address >= 0 && pd->phy_address < PHY_MAX_ADDR) 441 ppd->phy_mask = 1 << pd->phy_address; 442 else 443 ppd->phy_mask = 0; 444 } 445 } 446 447 static int bcmgenet_mii_wait(void *wait_func_data) 448 { 449 struct bcmgenet_priv *priv = wait_func_data; 450 451 wait_event_timeout(priv->wq, 452 !(bcmgenet_umac_readl(priv, UMAC_MDIO_CMD) 453 & MDIO_START_BUSY), 454 HZ / 100); 455 return 0; 456 } 457 458 static int bcmgenet_mii_register(struct bcmgenet_priv *priv) 459 { 460 struct platform_device *pdev = priv->pdev; 461 struct bcmgenet_platform_data *pdata = pdev->dev.platform_data; 462 struct device_node *dn = pdev->dev.of_node; 463 struct unimac_mdio_pdata ppd; 464 struct platform_device *ppdev; 465 struct resource *pres, res; 466 int id, ret; 467 468 pres = platform_get_resource(pdev, IORESOURCE_MEM, 0); 469 if (!pres) { 470 dev_err(&pdev->dev, "Invalid resource\n"); 471 return -EINVAL; 472 } 473 memset(&res, 0, sizeof(res)); 474 memset(&ppd, 0, sizeof(ppd)); 475 476 ppd.wait_func = bcmgenet_mii_wait; 477 ppd.wait_func_data = priv; 478 ppd.bus_name = "bcmgenet MII bus"; 479 /* Pass a reference to our "main" clock which is used for MDIO 480 * transfers 481 */ 482 ppd.clk = priv->clk; 483 484 /* Unimac MDIO bus controller starts at UniMAC offset + MDIO_CMD 485 * and is 2 * 32-bits word long, 8 bytes total. 486 */ 487 res.start = pres->start + GENET_UMAC_OFF + UMAC_MDIO_CMD; 488 res.end = res.start + 8; 489 res.flags = IORESOURCE_MEM; 490 491 if (dn) 492 id = of_alias_get_id(dn, "eth"); 493 else 494 id = pdev->id; 495 496 ppdev = platform_device_alloc(UNIMAC_MDIO_DRV_NAME, id); 497 if (!ppdev) 498 return -ENOMEM; 499 500 /* Retain this platform_device pointer for later cleanup */ 501 priv->mii_pdev = ppdev; 502 ppdev->dev.parent = &pdev->dev; 503 if (dn) 504 ppdev->dev.of_node = bcmgenet_mii_of_find_mdio(priv); 505 else if (pdata) 506 bcmgenet_mii_pdata_init(priv, &ppd); 507 else 508 ppd.phy_mask = ~0; 509 510 ret = platform_device_add_resources(ppdev, &res, 1); 511 if (ret) 512 goto out; 513 514 ret = platform_device_add_data(ppdev, &ppd, sizeof(ppd)); 515 if (ret) 516 goto out; 517 518 ret = platform_device_add(ppdev); 519 if (ret) 520 goto out; 521 522 return 0; 523 out: 524 platform_device_put(ppdev); 525 return ret; 526 } 527 528 static int bcmgenet_phy_interface_init(struct bcmgenet_priv *priv) 529 { 530 struct device *kdev = &priv->pdev->dev; 531 int phy_mode = device_get_phy_mode(kdev); 532 533 if (phy_mode < 0) { 534 dev_err(kdev, "invalid PHY mode property\n"); 535 return phy_mode; 536 } 537 538 priv->phy_interface = phy_mode; 539 540 /* We need to specifically look up whether this PHY interface is 541 * internal or not *before* we even try to probe the PHY driver 542 * over MDIO as we may have shut down the internal PHY for power 543 * saving purposes. 544 */ 545 if (priv->phy_interface == PHY_INTERFACE_MODE_INTERNAL) 546 priv->internal_phy = true; 547 548 return 0; 549 } 550 551 static int bcmgenet_mii_of_init(struct bcmgenet_priv *priv) 552 { 553 struct device_node *dn = priv->pdev->dev.of_node; 554 struct phy_device *phydev; 555 int ret; 556 557 /* Fetch the PHY phandle */ 558 priv->phy_dn = of_parse_phandle(dn, "phy-handle", 0); 559 560 /* In the case of a fixed PHY, the DT node associated 561 * to the PHY is the Ethernet MAC DT node. 562 */ 563 if (!priv->phy_dn && of_phy_is_fixed_link(dn)) { 564 ret = of_phy_register_fixed_link(dn); 565 if (ret) 566 return ret; 567 568 priv->phy_dn = of_node_get(dn); 569 } 570 571 /* Get the link mode */ 572 ret = bcmgenet_phy_interface_init(priv); 573 if (ret) 574 return ret; 575 576 /* Make sure we initialize MoCA PHYs with a link down */ 577 if (priv->phy_interface == PHY_INTERFACE_MODE_MOCA) { 578 phydev = of_phy_find_device(dn); 579 if (phydev) { 580 phydev->link = 0; 581 put_device(&phydev->mdio.dev); 582 } 583 } 584 585 return 0; 586 } 587 588 static int bcmgenet_mii_pd_init(struct bcmgenet_priv *priv) 589 { 590 struct device *kdev = &priv->pdev->dev; 591 struct bcmgenet_platform_data *pd = kdev->platform_data; 592 char phy_name[MII_BUS_ID_SIZE + 3]; 593 char mdio_bus_id[MII_BUS_ID_SIZE]; 594 struct phy_device *phydev; 595 596 snprintf(mdio_bus_id, MII_BUS_ID_SIZE, "%s-%d", 597 UNIMAC_MDIO_DRV_NAME, priv->pdev->id); 598 599 if (pd->phy_interface != PHY_INTERFACE_MODE_MOCA && pd->mdio_enabled) { 600 snprintf(phy_name, MII_BUS_ID_SIZE, PHY_ID_FMT, 601 mdio_bus_id, pd->phy_address); 602 603 /* 604 * Internal or external PHY with MDIO access 605 */ 606 phydev = phy_attach(priv->dev, phy_name, pd->phy_interface); 607 if (IS_ERR(phydev)) { 608 dev_err(kdev, "failed to register PHY device\n"); 609 return PTR_ERR(phydev); 610 } 611 } else { 612 /* 613 * MoCA port or no MDIO access. 614 * Use fixed PHY to represent the link layer. 615 */ 616 struct fixed_phy_status fphy_status = { 617 .link = 1, 618 .speed = pd->phy_speed, 619 .duplex = pd->phy_duplex, 620 .pause = 0, 621 .asym_pause = 0, 622 }; 623 624 phydev = fixed_phy_register(PHY_POLL, &fphy_status, NULL); 625 if (IS_ERR(phydev)) { 626 dev_err(kdev, "failed to register fixed PHY device\n"); 627 return PTR_ERR(phydev); 628 } 629 630 /* Make sure we initialize MoCA PHYs with a link down */ 631 phydev->link = 0; 632 633 } 634 635 priv->phy_interface = pd->phy_interface; 636 637 return 0; 638 } 639 640 static int bcmgenet_mii_bus_init(struct bcmgenet_priv *priv) 641 { 642 struct device *kdev = &priv->pdev->dev; 643 struct device_node *dn = kdev->of_node; 644 645 if (dn) 646 return bcmgenet_mii_of_init(priv); 647 else if (has_acpi_companion(kdev)) 648 return bcmgenet_phy_interface_init(priv); 649 else 650 return bcmgenet_mii_pd_init(priv); 651 } 652 653 int bcmgenet_mii_init(struct net_device *dev) 654 { 655 struct bcmgenet_priv *priv = netdev_priv(dev); 656 int ret; 657 658 ret = bcmgenet_mii_register(priv); 659 if (ret) 660 return ret; 661 662 ret = bcmgenet_mii_bus_init(priv); 663 if (ret) 664 goto out; 665 666 return 0; 667 668 out: 669 bcmgenet_mii_exit(dev); 670 return ret; 671 } 672 673 void bcmgenet_mii_exit(struct net_device *dev) 674 { 675 struct bcmgenet_priv *priv = netdev_priv(dev); 676 struct device_node *dn = priv->pdev->dev.of_node; 677 678 if (of_phy_is_fixed_link(dn)) 679 of_phy_deregister_fixed_link(dn); 680 of_node_put(priv->phy_dn); 681 platform_device_unregister(priv->mii_pdev); 682 } 683