1 /* SPDX-License-Identifier: GPL-2.0-or-later */ 2 /* 3 * Copyright(c) 2007 Atheros Corporation. All rights reserved. 4 * 5 * Derived from Intel e1000 driver 6 * Copyright(c) 1999 - 2005 Intel Corporation. All rights reserved. 7 */ 8 9 #ifndef _ATHL1E_HW_H_ 10 #define _ATHL1E_HW_H_ 11 12 #include <linux/types.h> 13 #include <linux/mii.h> 14 15 struct atl1e_adapter; 16 struct atl1e_hw; 17 18 /* function prototype */ 19 s32 atl1e_reset_hw(struct atl1e_hw *hw); 20 s32 atl1e_read_mac_addr(struct atl1e_hw *hw); 21 s32 atl1e_init_hw(struct atl1e_hw *hw); 22 s32 atl1e_phy_commit(struct atl1e_hw *hw); 23 s32 atl1e_get_speed_and_duplex(struct atl1e_hw *hw, u16 *speed, u16 *duplex); 24 u32 atl1e_auto_get_fc(struct atl1e_adapter *adapter, u16 duplex); 25 u32 atl1e_hash_mc_addr(struct atl1e_hw *hw, u8 *mc_addr); 26 void atl1e_hash_set(struct atl1e_hw *hw, u32 hash_value); 27 s32 atl1e_read_phy_reg(struct atl1e_hw *hw, u16 reg_addr, u16 *phy_data); 28 s32 atl1e_write_phy_reg(struct atl1e_hw *hw, u32 reg_addr, u16 phy_data); 29 s32 atl1e_validate_mdi_setting(struct atl1e_hw *hw); 30 void atl1e_hw_set_mac_addr(struct atl1e_hw *hw); 31 bool atl1e_read_eeprom(struct atl1e_hw *hw, u32 offset, u32 *p_value); 32 bool atl1e_write_eeprom(struct atl1e_hw *hw, u32 offset, u32 value); 33 s32 atl1e_phy_enter_power_saving(struct atl1e_hw *hw); 34 s32 atl1e_phy_leave_power_saving(struct atl1e_hw *hw); 35 s32 atl1e_phy_init(struct atl1e_hw *hw); 36 int atl1e_check_eeprom_exist(struct atl1e_hw *hw); 37 void atl1e_force_ps(struct atl1e_hw *hw); 38 s32 atl1e_restart_autoneg(struct atl1e_hw *hw); 39 40 /* register definition */ 41 #define REG_PM_CTRLSTAT 0x44 42 43 #define REG_PCIE_CAP_LIST 0x58 44 45 #define REG_DEVICE_CAP 0x5C 46 #define DEVICE_CAP_MAX_PAYLOAD_MASK 0x7 47 #define DEVICE_CAP_MAX_PAYLOAD_SHIFT 0 48 49 #define REG_DEVICE_CTRL 0x60 50 #define DEVICE_CTRL_MAX_PAYLOAD_MASK 0x7 51 #define DEVICE_CTRL_MAX_PAYLOAD_SHIFT 5 52 #define DEVICE_CTRL_MAX_RREQ_SZ_MASK 0x7 53 #define DEVICE_CTRL_MAX_RREQ_SZ_SHIFT 12 54 55 #define REG_VPD_CAP 0x6C 56 #define VPD_CAP_ID_MASK 0xff 57 #define VPD_CAP_ID_SHIFT 0 58 #define VPD_CAP_NEXT_PTR_MASK 0xFF 59 #define VPD_CAP_NEXT_PTR_SHIFT 8 60 #define VPD_CAP_VPD_ADDR_MASK 0x7FFF 61 #define VPD_CAP_VPD_ADDR_SHIFT 16 62 #define VPD_CAP_VPD_FLAG 0x80000000 63 64 #define REG_VPD_DATA 0x70 65 66 #define REG_SPI_FLASH_CTRL 0x200 67 #define SPI_FLASH_CTRL_STS_NON_RDY 0x1 68 #define SPI_FLASH_CTRL_STS_WEN 0x2 69 #define SPI_FLASH_CTRL_STS_WPEN 0x80 70 #define SPI_FLASH_CTRL_DEV_STS_MASK 0xFF 71 #define SPI_FLASH_CTRL_DEV_STS_SHIFT 0 72 #define SPI_FLASH_CTRL_INS_MASK 0x7 73 #define SPI_FLASH_CTRL_INS_SHIFT 8 74 #define SPI_FLASH_CTRL_START 0x800 75 #define SPI_FLASH_CTRL_EN_VPD 0x2000 76 #define SPI_FLASH_CTRL_LDSTART 0x8000 77 #define SPI_FLASH_CTRL_CS_HI_MASK 0x3 78 #define SPI_FLASH_CTRL_CS_HI_SHIFT 16 79 #define SPI_FLASH_CTRL_CS_HOLD_MASK 0x3 80 #define SPI_FLASH_CTRL_CS_HOLD_SHIFT 18 81 #define SPI_FLASH_CTRL_CLK_LO_MASK 0x3 82 #define SPI_FLASH_CTRL_CLK_LO_SHIFT 20 83 #define SPI_FLASH_CTRL_CLK_HI_MASK 0x3 84 #define SPI_FLASH_CTRL_CLK_HI_SHIFT 22 85 #define SPI_FLASH_CTRL_CS_SETUP_MASK 0x3 86 #define SPI_FLASH_CTRL_CS_SETUP_SHIFT 24 87 #define SPI_FLASH_CTRL_EROM_PGSZ_MASK 0x3 88 #define SPI_FLASH_CTRL_EROM_PGSZ_SHIFT 26 89 #define SPI_FLASH_CTRL_WAIT_READY 0x10000000 90 91 #define REG_SPI_ADDR 0x204 92 93 #define REG_SPI_DATA 0x208 94 95 #define REG_SPI_FLASH_CONFIG 0x20C 96 #define SPI_FLASH_CONFIG_LD_ADDR_MASK 0xFFFFFF 97 #define SPI_FLASH_CONFIG_LD_ADDR_SHIFT 0 98 #define SPI_FLASH_CONFIG_VPD_ADDR_MASK 0x3 99 #define SPI_FLASH_CONFIG_VPD_ADDR_SHIFT 24 100 #define SPI_FLASH_CONFIG_LD_EXIST 0x4000000 101 102 103 #define REG_SPI_FLASH_OP_PROGRAM 0x210 104 #define REG_SPI_FLASH_OP_SC_ERASE 0x211 105 #define REG_SPI_FLASH_OP_CHIP_ERASE 0x212 106 #define REG_SPI_FLASH_OP_RDID 0x213 107 #define REG_SPI_FLASH_OP_WREN 0x214 108 #define REG_SPI_FLASH_OP_RDSR 0x215 109 #define REG_SPI_FLASH_OP_WRSR 0x216 110 #define REG_SPI_FLASH_OP_READ 0x217 111 112 #define REG_TWSI_CTRL 0x218 113 #define TWSI_CTRL_LD_OFFSET_MASK 0xFF 114 #define TWSI_CTRL_LD_OFFSET_SHIFT 0 115 #define TWSI_CTRL_LD_SLV_ADDR_MASK 0x7 116 #define TWSI_CTRL_LD_SLV_ADDR_SHIFT 8 117 #define TWSI_CTRL_SW_LDSTART 0x800 118 #define TWSI_CTRL_HW_LDSTART 0x1000 119 #define TWSI_CTRL_SMB_SLV_ADDR_MASK 0x7F 120 #define TWSI_CTRL_SMB_SLV_ADDR_SHIFT 15 121 #define TWSI_CTRL_LD_EXIST 0x400000 122 #define TWSI_CTRL_READ_FREQ_SEL_MASK 0x3 123 #define TWSI_CTRL_READ_FREQ_SEL_SHIFT 23 124 #define TWSI_CTRL_FREQ_SEL_100K 0 125 #define TWSI_CTRL_FREQ_SEL_200K 1 126 #define TWSI_CTRL_FREQ_SEL_300K 2 127 #define TWSI_CTRL_FREQ_SEL_400K 3 128 #define TWSI_CTRL_SMB_SLV_ADDR 129 #define TWSI_CTRL_WRITE_FREQ_SEL_MASK 0x3 130 #define TWSI_CTRL_WRITE_FREQ_SEL_SHIFT 24 131 132 133 #define REG_PCIE_DEV_MISC_CTRL 0x21C 134 #define PCIE_DEV_MISC_CTRL_EXT_PIPE 0x2 135 #define PCIE_DEV_MISC_CTRL_RETRY_BUFDIS 0x1 136 #define PCIE_DEV_MISC_CTRL_SPIROM_EXIST 0x4 137 #define PCIE_DEV_MISC_CTRL_SERDES_ENDIAN 0x8 138 #define PCIE_DEV_MISC_CTRL_SERDES_SEL_DIN 0x10 139 140 #define REG_PCIE_PHYMISC 0x1000 141 #define PCIE_PHYMISC_FORCE_RCV_DET 0x4 142 143 #define REG_LTSSM_TEST_MODE 0x12FC 144 #define LTSSM_TEST_MODE_DEF 0xE000 145 146 /* Selene Master Control Register */ 147 #define REG_MASTER_CTRL 0x1400 148 #define MASTER_CTRL_SOFT_RST 0x1 149 #define MASTER_CTRL_MTIMER_EN 0x2 150 #define MASTER_CTRL_ITIMER_EN 0x4 151 #define MASTER_CTRL_MANUAL_INT 0x8 152 #define MASTER_CTRL_ITIMER2_EN 0x20 153 #define MASTER_CTRL_INT_RDCLR 0x40 154 #define MASTER_CTRL_LED_MODE 0x200 155 #define MASTER_CTRL_REV_NUM_SHIFT 16 156 #define MASTER_CTRL_REV_NUM_MASK 0xff 157 #define MASTER_CTRL_DEV_ID_SHIFT 24 158 #define MASTER_CTRL_DEV_ID_MASK 0xff 159 160 /* Timer Initial Value Register */ 161 #define REG_MANUAL_TIMER_INIT 0x1404 162 163 164 /* IRQ ModeratorTimer Initial Value Register */ 165 #define REG_IRQ_MODU_TIMER_INIT 0x1408 /* w */ 166 #define REG_IRQ_MODU_TIMER2_INIT 0x140A /* w */ 167 168 169 #define REG_GPHY_CTRL 0x140C 170 #define GPHY_CTRL_EXT_RESET 1 171 #define GPHY_CTRL_PIPE_MOD 2 172 #define GPHY_CTRL_TEST_MODE_MASK 3 173 #define GPHY_CTRL_TEST_MODE_SHIFT 2 174 #define GPHY_CTRL_BERT_START 0x10 175 #define GPHY_CTRL_GATE_25M_EN 0x20 176 #define GPHY_CTRL_LPW_EXIT 0x40 177 #define GPHY_CTRL_PHY_IDDQ 0x80 178 #define GPHY_CTRL_PHY_IDDQ_DIS 0x100 179 #define GPHY_CTRL_PCLK_SEL_DIS 0x200 180 #define GPHY_CTRL_HIB_EN 0x400 181 #define GPHY_CTRL_HIB_PULSE 0x800 182 #define GPHY_CTRL_SEL_ANA_RST 0x1000 183 #define GPHY_CTRL_PHY_PLL_ON 0x2000 184 #define GPHY_CTRL_PWDOWN_HW 0x4000 185 #define GPHY_CTRL_DEFAULT (\ 186 GPHY_CTRL_PHY_PLL_ON |\ 187 GPHY_CTRL_SEL_ANA_RST |\ 188 GPHY_CTRL_HIB_PULSE |\ 189 GPHY_CTRL_HIB_EN) 190 191 #define GPHY_CTRL_PW_WOL_DIS (\ 192 GPHY_CTRL_PHY_PLL_ON |\ 193 GPHY_CTRL_SEL_ANA_RST |\ 194 GPHY_CTRL_HIB_PULSE |\ 195 GPHY_CTRL_HIB_EN |\ 196 GPHY_CTRL_PWDOWN_HW |\ 197 GPHY_CTRL_PCLK_SEL_DIS |\ 198 GPHY_CTRL_PHY_IDDQ) 199 200 /* IRQ Anti-Lost Timer Initial Value Register */ 201 #define REG_CMBDISDMA_TIMER 0x140E 202 203 204 /* Block IDLE Status Register */ 205 #define REG_IDLE_STATUS 0x1410 206 #define IDLE_STATUS_RXMAC 1 /* 1: RXMAC state machine is in non-IDLE state. 0: RXMAC is idling */ 207 #define IDLE_STATUS_TXMAC 2 /* 1: TXMAC state machine is in non-IDLE state. 0: TXMAC is idling */ 208 #define IDLE_STATUS_RXQ 4 /* 1: RXQ state machine is in non-IDLE state. 0: RXQ is idling */ 209 #define IDLE_STATUS_TXQ 8 /* 1: TXQ state machine is in non-IDLE state. 0: TXQ is idling */ 210 #define IDLE_STATUS_DMAR 0x10 /* 1: DMAR state machine is in non-IDLE state. 0: DMAR is idling */ 211 #define IDLE_STATUS_DMAW 0x20 /* 1: DMAW state machine is in non-IDLE state. 0: DMAW is idling */ 212 #define IDLE_STATUS_SMB 0x40 /* 1: SMB state machine is in non-IDLE state. 0: SMB is idling */ 213 #define IDLE_STATUS_CMB 0x80 /* 1: CMB state machine is in non-IDLE state. 0: CMB is idling */ 214 215 /* MDIO Control Register */ 216 #define REG_MDIO_CTRL 0x1414 217 #define MDIO_DATA_MASK 0xffff /* On MDIO write, the 16-bit control data to write to PHY MII management register */ 218 #define MDIO_DATA_SHIFT 0 /* On MDIO read, the 16-bit status data that was read from the PHY MII management register*/ 219 #define MDIO_REG_ADDR_MASK 0x1f /* MDIO register address */ 220 #define MDIO_REG_ADDR_SHIFT 16 221 #define MDIO_RW 0x200000 /* 1: read, 0: write */ 222 #define MDIO_SUP_PREAMBLE 0x400000 /* Suppress preamble */ 223 #define MDIO_START 0x800000 /* Write 1 to initiate the MDIO master. And this bit is self cleared after one cycle*/ 224 #define MDIO_CLK_SEL_SHIFT 24 225 #define MDIO_CLK_25_4 0 226 #define MDIO_CLK_25_6 2 227 #define MDIO_CLK_25_8 3 228 #define MDIO_CLK_25_10 4 229 #define MDIO_CLK_25_14 5 230 #define MDIO_CLK_25_20 6 231 #define MDIO_CLK_25_28 7 232 #define MDIO_BUSY 0x8000000 233 #define MDIO_AP_EN 0x10000000 234 #define MDIO_WAIT_TIMES 10 235 236 /* MII PHY Status Register */ 237 #define REG_PHY_STATUS 0x1418 238 #define PHY_STATUS_100M 0x20000 239 #define PHY_STATUS_EMI_CA 0x40000 240 241 /* BIST Control and Status Register0 (for the Packet Memory) */ 242 #define REG_BIST0_CTRL 0x141c 243 #define BIST0_NOW 0x1 /* 1: To trigger BIST0 logic. This bit stays high during the */ 244 /* BIST process and reset to zero when BIST is done */ 245 #define BIST0_SRAM_FAIL 0x2 /* 1: The SRAM failure is un-repairable because it has address */ 246 /* decoder failure or more than 1 cell stuck-to-x failure */ 247 #define BIST0_FUSE_FLAG 0x4 /* 1: Indicating one cell has been fixed */ 248 249 /* BIST Control and Status Register1(for the retry buffer of PCI Express) */ 250 #define REG_BIST1_CTRL 0x1420 251 #define BIST1_NOW 0x1 /* 1: To trigger BIST0 logic. This bit stays high during the */ 252 /* BIST process and reset to zero when BIST is done */ 253 #define BIST1_SRAM_FAIL 0x2 /* 1: The SRAM failure is un-repairable because it has address */ 254 /* decoder failure or more than 1 cell stuck-to-x failure.*/ 255 #define BIST1_FUSE_FLAG 0x4 256 257 /* SerDes Lock Detect Control and Status Register */ 258 #define REG_SERDES_LOCK 0x1424 259 #define SERDES_LOCK_DETECT 1 /* 1: SerDes lock detected . This signal comes from Analog SerDes */ 260 #define SERDES_LOCK_DETECT_EN 2 /* 1: Enable SerDes Lock detect function */ 261 262 /* MAC Control Register */ 263 #define REG_MAC_CTRL 0x1480 264 #define MAC_CTRL_TX_EN 1 /* 1: Transmit Enable */ 265 #define MAC_CTRL_RX_EN 2 /* 1: Receive Enable */ 266 #define MAC_CTRL_TX_FLOW 4 /* 1: Transmit Flow Control Enable */ 267 #define MAC_CTRL_RX_FLOW 8 /* 1: Receive Flow Control Enable */ 268 #define MAC_CTRL_LOOPBACK 0x10 /* 1: Loop back at G/MII Interface */ 269 #define MAC_CTRL_DUPLX 0x20 /* 1: Full-duplex mode 0: Half-duplex mode */ 270 #define MAC_CTRL_ADD_CRC 0x40 /* 1: Instruct MAC to attach CRC on all egress Ethernet frames */ 271 #define MAC_CTRL_PAD 0x80 /* 1: Instruct MAC to pad short frames to 60-bytes, and then attach CRC. This bit has higher priority over CRC_EN */ 272 #define MAC_CTRL_LENCHK 0x100 /* 1: Instruct MAC to check if length field matches the real packet length */ 273 #define MAC_CTRL_HUGE_EN 0x200 /* 1: receive Jumbo frame enable */ 274 #define MAC_CTRL_PRMLEN_SHIFT 10 /* Preamble length */ 275 #define MAC_CTRL_PRMLEN_MASK 0xf 276 #define MAC_CTRL_RMV_VLAN 0x4000 /* 1: to remove VLAN Tag automatically from all receive packets */ 277 #define MAC_CTRL_PROMIS_EN 0x8000 /* 1: Promiscuous Mode Enable */ 278 #define MAC_CTRL_TX_PAUSE 0x10000 /* 1: transmit test pause */ 279 #define MAC_CTRL_SCNT 0x20000 /* 1: shortcut slot time counter */ 280 #define MAC_CTRL_SRST_TX 0x40000 /* 1: synchronized reset Transmit MAC module */ 281 #define MAC_CTRL_TX_SIMURST 0x80000 /* 1: transmit simulation reset */ 282 #define MAC_CTRL_SPEED_SHIFT 20 /* 10: gigabit 01:10M/100M */ 283 #define MAC_CTRL_SPEED_MASK 0x300000 284 #define MAC_CTRL_SPEED_1000 2 285 #define MAC_CTRL_SPEED_10_100 1 286 #define MAC_CTRL_DBG_TX_BKPRESURE 0x400000 /* 1: transmit maximum backoff (half-duplex test bit) */ 287 #define MAC_CTRL_TX_HUGE 0x800000 /* 1: transmit huge enable */ 288 #define MAC_CTRL_RX_CHKSUM_EN 0x1000000 /* 1: RX checksum enable */ 289 #define MAC_CTRL_MC_ALL_EN 0x2000000 /* 1: upload all multicast frame without error to system */ 290 #define MAC_CTRL_BC_EN 0x4000000 /* 1: upload all broadcast frame without error to system */ 291 #define MAC_CTRL_DBG 0x8000000 /* 1: upload all received frame to system (Debug Mode) */ 292 293 /* MAC IPG/IFG Control Register */ 294 #define REG_MAC_IPG_IFG 0x1484 295 #define MAC_IPG_IFG_IPGT_SHIFT 0 /* Desired back to back inter-packet gap. The default is 96-bit time */ 296 #define MAC_IPG_IFG_IPGT_MASK 0x7f 297 #define MAC_IPG_IFG_MIFG_SHIFT 8 /* Minimum number of IFG to enforce in between RX frames */ 298 #define MAC_IPG_IFG_MIFG_MASK 0xff /* Frame gap below such IFP is dropped */ 299 #define MAC_IPG_IFG_IPGR1_SHIFT 16 /* 64bit Carrier-Sense window */ 300 #define MAC_IPG_IFG_IPGR1_MASK 0x7f 301 #define MAC_IPG_IFG_IPGR2_SHIFT 24 /* 96-bit IPG window */ 302 #define MAC_IPG_IFG_IPGR2_MASK 0x7f 303 304 /* MAC STATION ADDRESS */ 305 #define REG_MAC_STA_ADDR 0x1488 306 307 /* Hash table for multicast address */ 308 #define REG_RX_HASH_TABLE 0x1490 309 310 311 /* MAC Half-Duplex Control Register */ 312 #define REG_MAC_HALF_DUPLX_CTRL 0x1498 313 #define MAC_HALF_DUPLX_CTRL_LCOL_SHIFT 0 /* Collision Window */ 314 #define MAC_HALF_DUPLX_CTRL_LCOL_MASK 0x3ff 315 #define MAC_HALF_DUPLX_CTRL_RETRY_SHIFT 12 /* Retransmission maximum, afterwards the packet will be discarded */ 316 #define MAC_HALF_DUPLX_CTRL_RETRY_MASK 0xf 317 #define MAC_HALF_DUPLX_CTRL_EXC_DEF_EN 0x10000 /* 1: Allow the transmission of a packet which has been excessively deferred */ 318 #define MAC_HALF_DUPLX_CTRL_NO_BACK_C 0x20000 /* 1: No back-off on collision, immediately start the retransmission */ 319 #define MAC_HALF_DUPLX_CTRL_NO_BACK_P 0x40000 /* 1: No back-off on backpressure, immediately start the transmission after back pressure */ 320 #define MAC_HALF_DUPLX_CTRL_ABEBE 0x80000 /* 1: Alternative Binary Exponential Back-off Enabled */ 321 #define MAC_HALF_DUPLX_CTRL_ABEBT_SHIFT 20 /* Maximum binary exponential number */ 322 #define MAC_HALF_DUPLX_CTRL_ABEBT_MASK 0xf 323 #define MAC_HALF_DUPLX_CTRL_JAMIPG_SHIFT 24 /* IPG to start JAM for collision based flow control in half-duplex */ 324 #define MAC_HALF_DUPLX_CTRL_JAMIPG_MASK 0xf /* mode. In unit of 8-bit time */ 325 326 /* Maximum Frame Length Control Register */ 327 #define REG_MTU 0x149c 328 329 /* Wake-On-Lan control register */ 330 #define REG_WOL_CTRL 0x14a0 331 #define WOL_PATTERN_EN 0x00000001 332 #define WOL_PATTERN_PME_EN 0x00000002 333 #define WOL_MAGIC_EN 0x00000004 334 #define WOL_MAGIC_PME_EN 0x00000008 335 #define WOL_LINK_CHG_EN 0x00000010 336 #define WOL_LINK_CHG_PME_EN 0x00000020 337 #define WOL_PATTERN_ST 0x00000100 338 #define WOL_MAGIC_ST 0x00000200 339 #define WOL_LINKCHG_ST 0x00000400 340 #define WOL_CLK_SWITCH_EN 0x00008000 341 #define WOL_PT0_EN 0x00010000 342 #define WOL_PT1_EN 0x00020000 343 #define WOL_PT2_EN 0x00040000 344 #define WOL_PT3_EN 0x00080000 345 #define WOL_PT4_EN 0x00100000 346 #define WOL_PT5_EN 0x00200000 347 #define WOL_PT6_EN 0x00400000 348 /* WOL Length ( 2 DWORD ) */ 349 #define REG_WOL_PATTERN_LEN 0x14a4 350 #define WOL_PT_LEN_MASK 0x7f 351 #define WOL_PT0_LEN_SHIFT 0 352 #define WOL_PT1_LEN_SHIFT 8 353 #define WOL_PT2_LEN_SHIFT 16 354 #define WOL_PT3_LEN_SHIFT 24 355 #define WOL_PT4_LEN_SHIFT 0 356 #define WOL_PT5_LEN_SHIFT 8 357 #define WOL_PT6_LEN_SHIFT 16 358 359 /* Internal SRAM Partition Register */ 360 #define REG_SRAM_TRD_ADDR 0x1518 361 #define REG_SRAM_TRD_LEN 0x151C 362 #define REG_SRAM_RXF_ADDR 0x1520 363 #define REG_SRAM_RXF_LEN 0x1524 364 #define REG_SRAM_TXF_ADDR 0x1528 365 #define REG_SRAM_TXF_LEN 0x152C 366 #define REG_SRAM_TCPH_ADDR 0x1530 367 #define REG_SRAM_PKTH_ADDR 0x1532 368 369 /* Load Ptr Register */ 370 #define REG_LOAD_PTR 0x1534 /* Software sets this bit after the initialization of the head and tail */ 371 372 /* 373 * addresses of all descriptors, as well as the following descriptor 374 * control register, which triggers each function block to load the head 375 * pointer to prepare for the operation. This bit is then self-cleared 376 * after one cycle. 377 */ 378 379 /* Descriptor Control register */ 380 #define REG_RXF3_BASE_ADDR_HI 0x153C 381 #define REG_DESC_BASE_ADDR_HI 0x1540 382 #define REG_RXF0_BASE_ADDR_HI 0x1540 /* share with DESC BASE ADDR HI */ 383 #define REG_HOST_RXF0_PAGE0_LO 0x1544 384 #define REG_HOST_RXF0_PAGE1_LO 0x1548 385 #define REG_TPD_BASE_ADDR_LO 0x154C 386 #define REG_RXF1_BASE_ADDR_HI 0x1550 387 #define REG_RXF2_BASE_ADDR_HI 0x1554 388 #define REG_HOST_RXFPAGE_SIZE 0x1558 389 #define REG_TPD_RING_SIZE 0x155C 390 /* RSS about */ 391 #define REG_RSS_KEY0 0x14B0 392 #define REG_RSS_KEY1 0x14B4 393 #define REG_RSS_KEY2 0x14B8 394 #define REG_RSS_KEY3 0x14BC 395 #define REG_RSS_KEY4 0x14C0 396 #define REG_RSS_KEY5 0x14C4 397 #define REG_RSS_KEY6 0x14C8 398 #define REG_RSS_KEY7 0x14CC 399 #define REG_RSS_KEY8 0x14D0 400 #define REG_RSS_KEY9 0x14D4 401 #define REG_IDT_TABLE4 0x14E0 402 #define REG_IDT_TABLE5 0x14E4 403 #define REG_IDT_TABLE6 0x14E8 404 #define REG_IDT_TABLE7 0x14EC 405 #define REG_IDT_TABLE0 0x1560 406 #define REG_IDT_TABLE1 0x1564 407 #define REG_IDT_TABLE2 0x1568 408 #define REG_IDT_TABLE3 0x156C 409 #define REG_IDT_TABLE REG_IDT_TABLE0 410 #define REG_RSS_HASH_VALUE 0x1570 411 #define REG_RSS_HASH_FLAG 0x1574 412 #define REG_BASE_CPU_NUMBER 0x157C 413 414 415 /* TXQ Control Register */ 416 #define REG_TXQ_CTRL 0x1580 417 #define TXQ_CTRL_NUM_TPD_BURST_MASK 0xF 418 #define TXQ_CTRL_NUM_TPD_BURST_SHIFT 0 419 #define TXQ_CTRL_EN 0x20 /* 1: Enable TXQ */ 420 #define TXQ_CTRL_ENH_MODE 0x40 /* Performance enhancement mode, in which up to two back-to-back DMA read commands might be dispatched. */ 421 #define TXQ_CTRL_TXF_BURST_NUM_SHIFT 16 /* Number of data byte to read in a cache-aligned burst. Each SRAM entry is 8-byte in length. */ 422 #define TXQ_CTRL_TXF_BURST_NUM_MASK 0xffff 423 424 /* Jumbo packet Threshold for task offload */ 425 #define REG_TX_EARLY_TH 0x1584 /* Jumbo frame threshold in QWORD unit. Packet greater than */ 426 /* JUMBO_TASK_OFFLOAD_THRESHOLD will not be task offloaded. */ 427 #define TX_TX_EARLY_TH_MASK 0x7ff 428 #define TX_TX_EARLY_TH_SHIFT 0 429 430 431 /* RXQ Control Register */ 432 #define REG_RXQ_CTRL 0x15A0 433 #define RXQ_CTRL_PBA_ALIGN_32 0 /* rx-packet alignment */ 434 #define RXQ_CTRL_PBA_ALIGN_64 1 435 #define RXQ_CTRL_PBA_ALIGN_128 2 436 #define RXQ_CTRL_PBA_ALIGN_256 3 437 #define RXQ_CTRL_Q1_EN 0x10 438 #define RXQ_CTRL_Q2_EN 0x20 439 #define RXQ_CTRL_Q3_EN 0x40 440 #define RXQ_CTRL_IPV6_XSUM_VERIFY_EN 0x80 441 #define RXQ_CTRL_HASH_TLEN_SHIFT 8 442 #define RXQ_CTRL_HASH_TLEN_MASK 0xFF 443 #define RXQ_CTRL_HASH_TYPE_IPV4 0x10000 444 #define RXQ_CTRL_HASH_TYPE_IPV4_TCP 0x20000 445 #define RXQ_CTRL_HASH_TYPE_IPV6 0x40000 446 #define RXQ_CTRL_HASH_TYPE_IPV6_TCP 0x80000 447 #define RXQ_CTRL_RSS_MODE_DISABLE 0 448 #define RXQ_CTRL_RSS_MODE_SQSINT 0x4000000 449 #define RXQ_CTRL_RSS_MODE_MQUESINT 0x8000000 450 #define RXQ_CTRL_RSS_MODE_MQUEMINT 0xC000000 451 #define RXQ_CTRL_NIP_QUEUE_SEL_TBL 0x10000000 452 #define RXQ_CTRL_HASH_ENABLE 0x20000000 453 #define RXQ_CTRL_CUT_THRU_EN 0x40000000 454 #define RXQ_CTRL_EN 0x80000000 455 456 /* Rx jumbo packet threshold and rrd retirement timer */ 457 #define REG_RXQ_JMBOSZ_RRDTIM 0x15A4 458 /* 459 * Jumbo packet threshold for non-VLAN packet, in QWORD (64-bit) unit. 460 * When the packet length greater than or equal to this value, RXQ 461 * shall start cut-through forwarding of the received packet. 462 */ 463 #define RXQ_JMBOSZ_TH_MASK 0x7ff 464 #define RXQ_JMBOSZ_TH_SHIFT 0 /* RRD retirement timer. Decrement by 1 after every 512ns passes*/ 465 #define RXQ_JMBO_LKAH_MASK 0xf 466 #define RXQ_JMBO_LKAH_SHIFT 11 467 468 /* RXF flow control register */ 469 #define REG_RXQ_RXF_PAUSE_THRESH 0x15A8 470 #define RXQ_RXF_PAUSE_TH_HI_SHIFT 0 471 #define RXQ_RXF_PAUSE_TH_HI_MASK 0xfff 472 #define RXQ_RXF_PAUSE_TH_LO_SHIFT 16 473 #define RXQ_RXF_PAUSE_TH_LO_MASK 0xfff 474 475 476 /* DMA Engine Control Register */ 477 #define REG_DMA_CTRL 0x15C0 478 #define DMA_CTRL_DMAR_IN_ORDER 0x1 479 #define DMA_CTRL_DMAR_ENH_ORDER 0x2 480 #define DMA_CTRL_DMAR_OUT_ORDER 0x4 481 #define DMA_CTRL_RCB_VALUE 0x8 482 #define DMA_CTRL_DMAR_BURST_LEN_SHIFT 4 483 #define DMA_CTRL_DMAR_BURST_LEN_MASK 7 484 #define DMA_CTRL_DMAW_BURST_LEN_SHIFT 7 485 #define DMA_CTRL_DMAW_BURST_LEN_MASK 7 486 #define DMA_CTRL_DMAR_REQ_PRI 0x400 487 #define DMA_CTRL_DMAR_DLY_CNT_MASK 0x1F 488 #define DMA_CTRL_DMAR_DLY_CNT_SHIFT 11 489 #define DMA_CTRL_DMAW_DLY_CNT_MASK 0xF 490 #define DMA_CTRL_DMAW_DLY_CNT_SHIFT 16 491 #define DMA_CTRL_TXCMB_EN 0x100000 492 #define DMA_CTRL_RXCMB_EN 0x200000 493 494 495 /* CMB/SMB Control Register */ 496 #define REG_SMB_STAT_TIMER 0x15C4 497 #define REG_TRIG_RRD_THRESH 0x15CA 498 #define REG_TRIG_TPD_THRESH 0x15C8 499 #define REG_TRIG_TXTIMER 0x15CC 500 #define REG_TRIG_RXTIMER 0x15CE 501 502 /* HOST RXF Page 1,2,3 address */ 503 #define REG_HOST_RXF1_PAGE0_LO 0x15D0 504 #define REG_HOST_RXF1_PAGE1_LO 0x15D4 505 #define REG_HOST_RXF2_PAGE0_LO 0x15D8 506 #define REG_HOST_RXF2_PAGE1_LO 0x15DC 507 #define REG_HOST_RXF3_PAGE0_LO 0x15E0 508 #define REG_HOST_RXF3_PAGE1_LO 0x15E4 509 510 /* Mail box */ 511 #define REG_MB_RXF1_RADDR 0x15B4 512 #define REG_MB_RXF2_RADDR 0x15B8 513 #define REG_MB_RXF3_RADDR 0x15BC 514 #define REG_MB_TPD_PROD_IDX 0x15F0 515 516 /* RXF-Page 0-3 PageNo & Valid bit */ 517 #define REG_HOST_RXF0_PAGE0_VLD 0x15F4 518 #define HOST_RXF_VALID 1 519 #define HOST_RXF_PAGENO_SHIFT 1 520 #define HOST_RXF_PAGENO_MASK 0x7F 521 #define REG_HOST_RXF0_PAGE1_VLD 0x15F5 522 #define REG_HOST_RXF1_PAGE0_VLD 0x15F6 523 #define REG_HOST_RXF1_PAGE1_VLD 0x15F7 524 #define REG_HOST_RXF2_PAGE0_VLD 0x15F8 525 #define REG_HOST_RXF2_PAGE1_VLD 0x15F9 526 #define REG_HOST_RXF3_PAGE0_VLD 0x15FA 527 #define REG_HOST_RXF3_PAGE1_VLD 0x15FB 528 529 /* Interrupt Status Register */ 530 #define REG_ISR 0x1600 531 #define ISR_SMB 1 532 #define ISR_TIMER 2 /* Interrupt when Timer is counted down to zero */ 533 /* 534 * Software manual interrupt, for debug. Set when SW_MAN_INT_EN is set 535 * in Table 51 Selene Master Control Register (Offset 0x1400). 536 */ 537 #define ISR_MANUAL 4 538 #define ISR_HW_RXF_OV 8 /* RXF overflow interrupt */ 539 #define ISR_HOST_RXF0_OV 0x10 540 #define ISR_HOST_RXF1_OV 0x20 541 #define ISR_HOST_RXF2_OV 0x40 542 #define ISR_HOST_RXF3_OV 0x80 543 #define ISR_TXF_UN 0x100 544 #define ISR_RX0_PAGE_FULL 0x200 545 #define ISR_DMAR_TO_RST 0x400 546 #define ISR_DMAW_TO_RST 0x800 547 #define ISR_GPHY 0x1000 548 #define ISR_TX_CREDIT 0x2000 549 #define ISR_GPHY_LPW 0x4000 /* GPHY low power state interrupt */ 550 #define ISR_RX_PKT 0x10000 /* One packet received, triggered by RFD */ 551 #define ISR_TX_PKT 0x20000 /* One packet transmitted, triggered by TPD */ 552 #define ISR_TX_DMA 0x40000 553 #define ISR_RX_PKT_1 0x80000 554 #define ISR_RX_PKT_2 0x100000 555 #define ISR_RX_PKT_3 0x200000 556 #define ISR_MAC_RX 0x400000 557 #define ISR_MAC_TX 0x800000 558 #define ISR_UR_DETECTED 0x1000000 559 #define ISR_FERR_DETECTED 0x2000000 560 #define ISR_NFERR_DETECTED 0x4000000 561 #define ISR_CERR_DETECTED 0x8000000 562 #define ISR_PHY_LINKDOWN 0x10000000 563 #define ISR_DIS_INT 0x80000000 564 565 566 /* Interrupt Mask Register */ 567 #define REG_IMR 0x1604 568 569 570 #define IMR_NORMAL_MASK (\ 571 ISR_SMB |\ 572 ISR_TXF_UN |\ 573 ISR_HW_RXF_OV |\ 574 ISR_HOST_RXF0_OV|\ 575 ISR_MANUAL |\ 576 ISR_GPHY |\ 577 ISR_GPHY_LPW |\ 578 ISR_DMAR_TO_RST |\ 579 ISR_DMAW_TO_RST |\ 580 ISR_PHY_LINKDOWN|\ 581 ISR_RX_PKT |\ 582 ISR_TX_PKT) 583 584 #define ISR_TX_EVENT (ISR_TXF_UN | ISR_TX_PKT) 585 #define ISR_RX_EVENT (ISR_HOST_RXF0_OV | ISR_HW_RXF_OV | ISR_RX_PKT) 586 587 #define REG_MAC_RX_STATUS_BIN 0x1700 588 #define REG_MAC_RX_STATUS_END 0x175c 589 #define REG_MAC_TX_STATUS_BIN 0x1760 590 #define REG_MAC_TX_STATUS_END 0x17c0 591 592 /* Hardware Offset Register */ 593 #define REG_HOST_RXF0_PAGEOFF 0x1800 594 #define REG_TPD_CONS_IDX 0x1804 595 #define REG_HOST_RXF1_PAGEOFF 0x1808 596 #define REG_HOST_RXF2_PAGEOFF 0x180C 597 #define REG_HOST_RXF3_PAGEOFF 0x1810 598 599 /* RXF-Page 0-3 Offset DMA Address */ 600 #define REG_HOST_RXF0_MB0_LO 0x1820 601 #define REG_HOST_RXF0_MB1_LO 0x1824 602 #define REG_HOST_RXF1_MB0_LO 0x1828 603 #define REG_HOST_RXF1_MB1_LO 0x182C 604 #define REG_HOST_RXF2_MB0_LO 0x1830 605 #define REG_HOST_RXF2_MB1_LO 0x1834 606 #define REG_HOST_RXF3_MB0_LO 0x1838 607 #define REG_HOST_RXF3_MB1_LO 0x183C 608 609 /* Tpd CMB DMA Address */ 610 #define REG_HOST_TX_CMB_LO 0x1840 611 #define REG_HOST_SMB_ADDR_LO 0x1844 612 613 /* DEBUG ADDR */ 614 #define REG_DEBUG_DATA0 0x1900 615 #define REG_DEBUG_DATA1 0x1904 616 617 /***************************** MII definition ***************************************/ 618 /* PHY Common Register */ 619 #define MII_AT001_PSCR 0x10 620 #define MII_AT001_PSSR 0x11 621 #define MII_INT_CTRL 0x12 622 #define MII_INT_STATUS 0x13 623 #define MII_SMARTSPEED 0x14 624 #define MII_LBRERROR 0x18 625 #define MII_RESV2 0x1a 626 627 #define MII_DBG_ADDR 0x1D 628 #define MII_DBG_DATA 0x1E 629 630 /* Autoneg Advertisement Register */ 631 #define MII_AR_DEFAULT_CAP_MASK 0 632 633 /* 1000BASE-T Control Register */ 634 #define MII_AT001_CR_1000T_SPEED_MASK \ 635 (ADVERTISE_1000FULL | ADVERTISE_1000HALF) 636 #define MII_AT001_CR_1000T_DEFAULT_CAP_MASK MII_AT001_CR_1000T_SPEED_MASK 637 638 /* AT001 PHY Specific Control Register */ 639 #define MII_AT001_PSCR_JABBER_DISABLE 0x0001 /* 1=Jabber Function disabled */ 640 #define MII_AT001_PSCR_POLARITY_REVERSAL 0x0002 /* 1=Polarity Reversal enabled */ 641 #define MII_AT001_PSCR_SQE_TEST 0x0004 /* 1=SQE Test enabled */ 642 #define MII_AT001_PSCR_MAC_POWERDOWN 0x0008 643 #define MII_AT001_PSCR_CLK125_DISABLE 0x0010 /* 1=CLK125 low, 644 * 0=CLK125 toggling 645 */ 646 #define MII_AT001_PSCR_MDI_MANUAL_MODE 0x0000 /* MDI Crossover Mode bits 6:5 */ 647 /* Manual MDI configuration */ 648 #define MII_AT001_PSCR_MDIX_MANUAL_MODE 0x0020 /* Manual MDIX configuration */ 649 #define MII_AT001_PSCR_AUTO_X_1000T 0x0040 /* 1000BASE-T: Auto crossover, 650 * 100BASE-TX/10BASE-T: 651 * MDI Mode 652 */ 653 #define MII_AT001_PSCR_AUTO_X_MODE 0x0060 /* Auto crossover enabled 654 * all speeds. 655 */ 656 #define MII_AT001_PSCR_10BT_EXT_DIST_ENABLE 0x0080 657 /* 1=Enable Extended 10BASE-T distance 658 * (Lower 10BASE-T RX Threshold) 659 * 0=Normal 10BASE-T RX Threshold */ 660 #define MII_AT001_PSCR_MII_5BIT_ENABLE 0x0100 661 /* 1=5-Bit interface in 100BASE-TX 662 * 0=MII interface in 100BASE-TX */ 663 #define MII_AT001_PSCR_SCRAMBLER_DISABLE 0x0200 /* 1=Scrambler disable */ 664 #define MII_AT001_PSCR_FORCE_LINK_GOOD 0x0400 /* 1=Force link good */ 665 #define MII_AT001_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */ 666 #define MII_AT001_PSCR_POLARITY_REVERSAL_SHIFT 1 667 #define MII_AT001_PSCR_AUTO_X_MODE_SHIFT 5 668 #define MII_AT001_PSCR_10BT_EXT_DIST_ENABLE_SHIFT 7 669 /* AT001 PHY Specific Status Register */ 670 #define MII_AT001_PSSR_SPD_DPLX_RESOLVED 0x0800 /* 1=Speed & Duplex resolved */ 671 #define MII_AT001_PSSR_DPLX 0x2000 /* 1=Duplex 0=Half Duplex */ 672 #define MII_AT001_PSSR_SPEED 0xC000 /* Speed, bits 14:15 */ 673 #define MII_AT001_PSSR_10MBS 0x0000 /* 00=10Mbs */ 674 #define MII_AT001_PSSR_100MBS 0x4000 /* 01=100Mbs */ 675 #define MII_AT001_PSSR_1000MBS 0x8000 /* 10=1000Mbs */ 676 677 #endif /*_ATHL1E_HW_H_*/ 678