1# 2# Network device configuration 3# 4 5menuconfig NETDEVICES 6 default y if UML 7 depends on NET 8 bool "Network device support" 9 ---help--- 10 You can say N here if you don't intend to connect your Linux box to 11 any other computer at all. 12 13 You'll have to say Y if your computer contains a network card that 14 you want to use under Linux. If you are going to run SLIP or PPP over 15 telephone line or null modem cable you need say Y here. Connecting 16 two machines with parallel ports using PLIP needs this, as well as 17 AX.25/KISS for sending Internet traffic over amateur radio links. 18 19 See also "The Linux Network Administrator's Guide" by Olaf Kirch and 20 Terry Dawson. Available at <http://www.tldp.org/guides.html>. 21 22 If unsure, say Y. 23 24# All the following symbols are dependent on NETDEVICES - do not repeat 25# that for each of the symbols. 26if NETDEVICES 27 28config NET_CORE 29 default y 30 bool "Network core driver support" 31 ---help--- 32 You can say N here if you do not intend to use any of the 33 networking core drivers (i.e. VLAN, bridging, bonding, etc.) 34 35if NET_CORE 36 37config BONDING 38 tristate "Bonding driver support" 39 depends on INET 40 depends on IPV6 || IPV6=n 41 ---help--- 42 Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet 43 Channels together. This is called 'Etherchannel' by Cisco, 44 'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux. 45 46 The driver supports multiple bonding modes to allow for both high 47 performance and high availability operation. 48 49 Refer to <file:Documentation/networking/bonding.txt> for more 50 information. 51 52 To compile this driver as a module, choose M here: the module 53 will be called bonding. 54 55config DUMMY 56 tristate "Dummy net driver support" 57 ---help--- 58 This is essentially a bit-bucket device (i.e. traffic you send to 59 this device is consigned into oblivion) with a configurable IP 60 address. It is most commonly used in order to make your currently 61 inactive SLIP address seem like a real address for local programs. 62 If you use SLIP or PPP, you might want to say Y here. Since this 63 thing often comes in handy, the default is Y. It won't enlarge your 64 kernel either. What a deal. Read about it in the Network 65 Administrator's Guide, available from 66 <http://www.tldp.org/docs.html#guide>. 67 68 To compile this driver as a module, choose M here: the module 69 will be called dummy. If you want to use more than one dummy 70 device at a time, you need to compile this driver as a module. 71 Instead of 'dummy', the devices will then be called 'dummy0', 72 'dummy1' etc. 73 74config EQUALIZER 75 tristate "EQL (serial line load balancing) support" 76 ---help--- 77 If you have two serial connections to some other computer (this 78 usually requires two modems and two telephone lines) and you use 79 SLIP (the protocol for sending Internet traffic over telephone 80 lines) or PPP (a better SLIP) on them, you can make them behave like 81 one double speed connection using this driver. Naturally, this has 82 to be supported at the other end as well, either with a similar EQL 83 Linux driver or with a Livingston Portmaster 2e. 84 85 Say Y if you want this and read 86 <file:Documentation/networking/eql.txt>. You may also want to read 87 section 6.2 of the NET-3-HOWTO, available from 88 <http://www.tldp.org/docs.html#howto>. 89 90 To compile this driver as a module, choose M here: the module 91 will be called eql. If unsure, say N. 92 93config NET_FC 94 bool "Fibre Channel driver support" 95 depends on SCSI && PCI 96 help 97 Fibre Channel is a high speed serial protocol mainly used to connect 98 large storage devices to the computer; it is compatible with and 99 intended to replace SCSI. 100 101 If you intend to use Fibre Channel, you need to have a Fibre channel 102 adaptor card in your computer; say Y here and to the driver for your 103 adaptor below. You also should have said Y to "SCSI support" and 104 "SCSI generic support". 105 106config MII 107 tristate "Generic Media Independent Interface device support" 108 help 109 Most ethernet controllers have MII transceiver either as an external 110 or internal device. It is safe to say Y or M here even if your 111 ethernet card lacks MII. 112 113source "drivers/ieee802154/Kconfig" 114 115config IFB 116 tristate "Intermediate Functional Block support" 117 depends on NET_CLS_ACT 118 ---help--- 119 This is an intermediate driver that allows sharing of 120 resources. 121 To compile this driver as a module, choose M here: the module 122 will be called ifb. If you want to use more than one ifb 123 device at a time, you need to compile this driver as a module. 124 Instead of 'ifb', the devices will then be called 'ifb0', 125 'ifb1' etc. 126 Look at the iproute2 documentation directory for usage etc 127 128config MACVLAN 129 tristate "MAC-VLAN support (EXPERIMENTAL)" 130 depends on EXPERIMENTAL 131 ---help--- 132 This allows one to create virtual interfaces that map packets to 133 or from specific MAC addresses to a particular interface. 134 135 Macvlan devices can be added using the "ip" command from the 136 iproute2 package starting with the iproute2-2.6.23 release: 137 138 "ip link add link <real dev> [ address MAC ] [ NAME ] type macvlan" 139 140 To compile this driver as a module, choose M here: the module 141 will be called macvlan. 142 143config MACVTAP 144 tristate "MAC-VLAN based tap driver (EXPERIMENTAL)" 145 depends on MACVLAN 146 help 147 This adds a specialized tap character device driver that is based 148 on the MAC-VLAN network interface, called macvtap. A macvtap device 149 can be added in the same way as a macvlan device, using 'type 150 macvlan', and then be accessed through the tap user space interface. 151 152 To compile this driver as a module, choose M here: the module 153 will be called macvtap. 154 155config NETCONSOLE 156 tristate "Network console logging support" 157 ---help--- 158 If you want to log kernel messages over the network, enable this. 159 See <file:Documentation/networking/netconsole.txt> for details. 160 161config NETCONSOLE_DYNAMIC 162 bool "Dynamic reconfiguration of logging targets" 163 depends on NETCONSOLE && SYSFS && CONFIGFS_FS && \ 164 !(NETCONSOLE=y && CONFIGFS_FS=m) 165 help 166 This option enables the ability to dynamically reconfigure target 167 parameters (interface, IP addresses, port numbers, MAC addresses) 168 at runtime through a userspace interface exported using configfs. 169 See <file:Documentation/networking/netconsole.txt> for details. 170 171config NETPOLL 172 def_bool NETCONSOLE 173 174config NETPOLL_TRAP 175 bool "Netpoll traffic trapping" 176 default n 177 depends on NETPOLL 178 179config NET_POLL_CONTROLLER 180 def_bool NETPOLL 181 182config RIONET 183 tristate "RapidIO Ethernet over messaging driver support" 184 depends on RAPIDIO 185 186config RIONET_TX_SIZE 187 int "Number of outbound queue entries" 188 depends on RIONET 189 default "128" 190 191config RIONET_RX_SIZE 192 int "Number of inbound queue entries" 193 depends on RIONET 194 default "128" 195 196config TUN 197 tristate "Universal TUN/TAP device driver support" 198 select CRC32 199 ---help--- 200 TUN/TAP provides packet reception and transmission for user space 201 programs. It can be viewed as a simple Point-to-Point or Ethernet 202 device, which instead of receiving packets from a physical media, 203 receives them from user space program and instead of sending packets 204 via physical media writes them to the user space program. 205 206 When a program opens /dev/net/tun, driver creates and registers 207 corresponding net device tunX or tapX. After a program closed above 208 devices, driver will automatically delete tunXX or tapXX device and 209 all routes corresponding to it. 210 211 Please read <file:Documentation/networking/tuntap.txt> for more 212 information. 213 214 To compile this driver as a module, choose M here: the module 215 will be called tun. 216 217 If you don't know what to use this for, you don't need it. 218 219config VETH 220 tristate "Virtual ethernet pair device" 221 ---help--- 222 This device is a local ethernet tunnel. Devices are created in pairs. 223 When one end receives the packet it appears on its pair and vice 224 versa. 225 226config VIRTIO_NET 227 tristate "Virtio network driver (EXPERIMENTAL)" 228 depends on EXPERIMENTAL && VIRTIO 229 ---help--- 230 This is the virtual network driver for virtio. It can be used with 231 lguest or QEMU based VMMs (like KVM or Xen). Say Y or M. 232 233endif # NET_CORE 234 235config SUNGEM_PHY 236 tristate 237 238source "drivers/net/arcnet/Kconfig" 239 240source "drivers/atm/Kconfig" 241 242source "drivers/net/caif/Kconfig" 243 244source "drivers/net/ethernet/Kconfig" 245 246source "drivers/net/fddi/Kconfig" 247 248config NET_SB1000 249 tristate "General Instruments Surfboard 1000" 250 depends on PNP 251 ---help--- 252 This is a driver for the General Instrument (also known as 253 NextLevel) SURFboard 1000 internal 254 cable modem. This is an ISA card which is used by a number of cable 255 TV companies to provide cable modem access. It's a one-way 256 downstream-only cable modem, meaning that your upstream net link is 257 provided by your regular phone modem. 258 259 At present this driver only compiles as a module, so say M here if 260 you have this card. The module will be called sb1000. Then read 261 <file:Documentation/networking/README.sb1000> for information on how 262 to use this module, as it needs special ppp scripts for establishing 263 a connection. Further documentation and the necessary scripts can be 264 found at: 265 266 <http://www.jacksonville.net/~fventuri/> 267 <http://home.adelphia.net/~siglercm/sb1000.html> 268 <http://linuxpower.cx/~cable/> 269 270 If you don't have this card, of course say N. 271 272source "drivers/net/phy/Kconfig" 273 274source "drivers/net/plip/Kconfig" 275 276source "drivers/net/ppp/Kconfig" 277 278source "drivers/net/slip/Kconfig" 279 280source "drivers/s390/net/Kconfig" 281 282source "drivers/net/tokenring/Kconfig" 283 284source "drivers/net/usb/Kconfig" 285 286source "drivers/net/wireless/Kconfig" 287 288source "drivers/net/wimax/Kconfig" 289 290source "drivers/net/wan/Kconfig" 291 292config XEN_NETDEV_FRONTEND 293 tristate "Xen network device frontend driver" 294 depends on XEN 295 select XEN_XENBUS_FRONTEND 296 default y 297 help 298 This driver provides support for Xen paravirtual network 299 devices exported by a Xen network driver domain (often 300 domain 0). 301 302 The corresponding Linux backend driver is enabled by the 303 CONFIG_XEN_NETDEV_BACKEND option. 304 305 If you are compiling a kernel for use as Xen guest, you 306 should say Y here. To compile this driver as a module, chose 307 M here: the module will be called xen-netfront. 308 309config XEN_NETDEV_BACKEND 310 tristate "Xen backend network device" 311 depends on XEN_BACKEND 312 help 313 This driver allows the kernel to act as a Xen network driver 314 domain which exports paravirtual network devices to other 315 Xen domains. These devices can be accessed by any operating 316 system that implements a compatible front end. 317 318 The corresponding Linux frontend driver is enabled by the 319 CONFIG_XEN_NETDEV_FRONTEND configuration option. 320 321 The backend driver presents a standard network device 322 endpoint for each paravirtual network device to the driver 323 domain network stack. These can then be bridged or routed 324 etc in order to provide full network connectivity. 325 326 If you are compiling a kernel to run in a Xen network driver 327 domain (often this is domain 0) you should say Y here. To 328 compile this driver as a module, chose M here: the module 329 will be called xen-netback. 330 331config VMXNET3 332 tristate "VMware VMXNET3 ethernet driver" 333 depends on PCI && INET 334 help 335 This driver supports VMware's vmxnet3 virtual ethernet NIC. 336 To compile this driver as a module, choose M here: the 337 module will be called vmxnet3. 338 339endif # NETDEVICES 340