1# 2# Network device configuration 3# 4 5config HAVE_NET_MACB 6 bool 7 8menuconfig NETDEVICES 9 default y if UML 10 depends on NET 11 bool "Network device support" 12 ---help--- 13 You can say N here if you don't intend to connect your Linux box to 14 any other computer at all. 15 16 You'll have to say Y if your computer contains a network card that 17 you want to use under Linux. If you are going to run SLIP or PPP over 18 telephone line or null modem cable you need say Y here. Connecting 19 two machines with parallel ports using PLIP needs this, as well as 20 AX.25/KISS for sending Internet traffic over amateur radio links. 21 22 See also "The Linux Network Administrator's Guide" by Olaf Kirch and 23 Terry Dawson. Available at <http://www.tldp.org/guides.html>. 24 25 If unsure, say Y. 26 27# All the following symbols are dependent on NETDEVICES - do not repeat 28# that for each of the symbols. 29if NETDEVICES 30 31config IFB 32 tristate "Intermediate Functional Block support" 33 depends on NET_CLS_ACT 34 ---help--- 35 This is an intermediate driver that allows sharing of 36 resources. 37 To compile this driver as a module, choose M here: the module 38 will be called ifb. If you want to use more than one ifb 39 device at a time, you need to compile this driver as a module. 40 Instead of 'ifb', the devices will then be called 'ifb0', 41 'ifb1' etc. 42 Look at the iproute2 documentation directory for usage etc 43 44config DUMMY 45 tristate "Dummy net driver support" 46 ---help--- 47 This is essentially a bit-bucket device (i.e. traffic you send to 48 this device is consigned into oblivion) with a configurable IP 49 address. It is most commonly used in order to make your currently 50 inactive SLIP address seem like a real address for local programs. 51 If you use SLIP or PPP, you might want to say Y here. Since this 52 thing often comes in handy, the default is Y. It won't enlarge your 53 kernel either. What a deal. Read about it in the Network 54 Administrator's Guide, available from 55 <http://www.tldp.org/docs.html#guide>. 56 57 To compile this driver as a module, choose M here: the module 58 will be called dummy. If you want to use more than one dummy 59 device at a time, you need to compile this driver as a module. 60 Instead of 'dummy', the devices will then be called 'dummy0', 61 'dummy1' etc. 62 63config BONDING 64 tristate "Bonding driver support" 65 depends on INET 66 depends on IPV6 || IPV6=n 67 ---help--- 68 Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet 69 Channels together. This is called 'Etherchannel' by Cisco, 70 'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux. 71 72 The driver supports multiple bonding modes to allow for both high 73 performance and high availability operation. 74 75 Refer to <file:Documentation/networking/bonding.txt> for more 76 information. 77 78 To compile this driver as a module, choose M here: the module 79 will be called bonding. 80 81config MACVLAN 82 tristate "MAC-VLAN support (EXPERIMENTAL)" 83 depends on EXPERIMENTAL 84 ---help--- 85 This allows one to create virtual interfaces that map packets to 86 or from specific MAC addresses to a particular interface. 87 88 Macvlan devices can be added using the "ip" command from the 89 iproute2 package starting with the iproute2-2.6.23 release: 90 91 "ip link add link <real dev> [ address MAC ] [ NAME ] type macvlan" 92 93 To compile this driver as a module, choose M here: the module 94 will be called macvlan. 95 96config MACVTAP 97 tristate "MAC-VLAN based tap driver (EXPERIMENTAL)" 98 depends on MACVLAN 99 help 100 This adds a specialized tap character device driver that is based 101 on the MAC-VLAN network interface, called macvtap. A macvtap device 102 can be added in the same way as a macvlan device, using 'type 103 macvlan', and then be accessed through the tap user space interface. 104 105 To compile this driver as a module, choose M here: the module 106 will be called macvtap. 107 108config EQUALIZER 109 tristate "EQL (serial line load balancing) support" 110 ---help--- 111 If you have two serial connections to some other computer (this 112 usually requires two modems and two telephone lines) and you use 113 SLIP (the protocol for sending Internet traffic over telephone 114 lines) or PPP (a better SLIP) on them, you can make them behave like 115 one double speed connection using this driver. Naturally, this has 116 to be supported at the other end as well, either with a similar EQL 117 Linux driver or with a Livingston Portmaster 2e. 118 119 Say Y if you want this and read 120 <file:Documentation/networking/eql.txt>. You may also want to read 121 section 6.2 of the NET-3-HOWTO, available from 122 <http://www.tldp.org/docs.html#howto>. 123 124 To compile this driver as a module, choose M here: the module 125 will be called eql. If unsure, say N. 126 127config TUN 128 tristate "Universal TUN/TAP device driver support" 129 select CRC32 130 ---help--- 131 TUN/TAP provides packet reception and transmission for user space 132 programs. It can be viewed as a simple Point-to-Point or Ethernet 133 device, which instead of receiving packets from a physical media, 134 receives them from user space program and instead of sending packets 135 via physical media writes them to the user space program. 136 137 When a program opens /dev/net/tun, driver creates and registers 138 corresponding net device tunX or tapX. After a program closed above 139 devices, driver will automatically delete tunXX or tapXX device and 140 all routes corresponding to it. 141 142 Please read <file:Documentation/networking/tuntap.txt> for more 143 information. 144 145 To compile this driver as a module, choose M here: the module 146 will be called tun. 147 148 If you don't know what to use this for, you don't need it. 149 150config VETH 151 tristate "Virtual ethernet pair device" 152 ---help--- 153 This device is a local ethernet tunnel. Devices are created in pairs. 154 When one end receives the packet it appears on its pair and vice 155 versa. 156 157config NET_SB1000 158 tristate "General Instruments Surfboard 1000" 159 depends on PNP 160 ---help--- 161 This is a driver for the General Instrument (also known as 162 NextLevel) SURFboard 1000 internal 163 cable modem. This is an ISA card which is used by a number of cable 164 TV companies to provide cable modem access. It's a one-way 165 downstream-only cable modem, meaning that your upstream net link is 166 provided by your regular phone modem. 167 168 At present this driver only compiles as a module, so say M here if 169 you have this card. The module will be called sb1000. Then read 170 <file:Documentation/networking/README.sb1000> for information on how 171 to use this module, as it needs special ppp scripts for establishing 172 a connection. Further documentation and the necessary scripts can be 173 found at: 174 175 <http://www.jacksonville.net/~fventuri/> 176 <http://home.adelphia.net/~siglercm/sb1000.html> 177 <http://linuxpower.cx/~cable/> 178 179 If you don't have this card, of course say N. 180 181source "drivers/net/arcnet/Kconfig" 182 183config MII 184 tristate "Generic Media Independent Interface device support" 185 help 186 Most ethernet controllers have MII transceiver either as an external 187 or internal device. It is safe to say Y or M here even if your 188 ethernet card lacks MII. 189 190source "drivers/net/phy/Kconfig" 191 192# 193# Ethernet 194# 195 196menuconfig NET_ETHERNET 197 bool "Ethernet (10 or 100Mbit)" 198 depends on !UML 199 ---help--- 200 Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common 201 type of Local Area Network (LAN) in universities and companies. 202 203 Common varieties of Ethernet are: 10BASE-2 or Thinnet (10 Mbps over 204 coaxial cable, linking computers in a chain), 10BASE-T or twisted 205 pair (10 Mbps over twisted pair cable, linking computers to central 206 hubs), 10BASE-F (10 Mbps over optical fiber links, using hubs), 207 100BASE-TX (100 Mbps over two twisted pair cables, using hubs), 208 100BASE-T4 (100 Mbps over 4 standard voice-grade twisted pair 209 cables, using hubs), 100BASE-FX (100 Mbps over optical fiber links) 210 [the 100BASE varieties are also known as Fast Ethernet], and Gigabit 211 Ethernet (1 Gbps over optical fiber or short copper links). 212 213 If your Linux machine will be connected to an Ethernet and you have 214 an Ethernet network interface card (NIC) installed in your computer, 215 say Y here and read the Ethernet-HOWTO, available from 216 <http://www.tldp.org/docs.html#howto>. You will then also have 217 to say Y to the driver for your particular NIC. 218 219 Note that the answer to this question won't directly affect the 220 kernel: saying N will just cause the configurator to skip all 221 the questions about Ethernet network cards. If unsure, say N. 222 223if NET_ETHERNET 224 225config MACB 226 tristate "Atmel MACB support" 227 depends on HAVE_NET_MACB 228 select PHYLIB 229 help 230 The Atmel MACB ethernet interface is found on many AT32 and AT91 231 parts. Say Y to include support for the MACB chip. 232 233 To compile this driver as a module, choose M here: the module 234 will be called macb. 235 236source "drivers/net/arm/Kconfig" 237 238config AX88796 239 tristate "ASIX AX88796 NE2000 clone support" 240 depends on ARM || MIPS || SUPERH 241 select PHYLIB 242 select MDIO_BITBANG 243 help 244 AX88796 driver, using platform bus to provide 245 chip detection and resources 246 247config AX88796_93CX6 248 bool "ASIX AX88796 external 93CX6 eeprom support" 249 depends on AX88796 250 select EEPROM_93CX6 251 help 252 Select this if your platform comes with an external 93CX6 eeprom. 253 254config MACE 255 tristate "MACE (Power Mac ethernet) support" 256 depends on PPC_PMAC && PPC32 257 select CRC32 258 help 259 Power Macintoshes and clones with Ethernet built-in on the 260 motherboard will usually use a MACE (Medium Access Control for 261 Ethernet) interface. Say Y to include support for the MACE chip. 262 263 To compile this driver as a module, choose M here: the module 264 will be called mace. 265 266config MACE_AAUI_PORT 267 bool "Use AAUI port instead of TP by default" 268 depends on MACE 269 help 270 Some Apple machines (notably the Apple Network Server) which use the 271 MACE ethernet chip have an Apple AUI port (small 15-pin connector), 272 instead of an 8-pin RJ45 connector for twisted-pair ethernet. Say 273 Y here if you have such a machine. If unsure, say N. 274 The driver will default to AAUI on ANS anyway, and if you use it as 275 a module, you can provide the port_aaui=0|1 to force the driver. 276 277config BMAC 278 tristate "BMAC (G3 ethernet) support" 279 depends on PPC_PMAC && PPC32 280 select CRC32 281 help 282 Say Y for support of BMAC Ethernet interfaces. These are used on G3 283 computers. 284 285 To compile this driver as a module, choose M here: the module 286 will be called bmac. 287 288config ARIADNE 289 tristate "Ariadne support" 290 depends on ZORRO 291 help 292 If you have a Village Tronic Ariadne Ethernet adapter, say Y. 293 Otherwise, say N. 294 295 To compile this driver as a module, choose M here: the module 296 will be called ariadne. 297 298config A2065 299 tristate "A2065 support" 300 depends on ZORRO 301 select CRC32 302 help 303 If you have a Commodore A2065 Ethernet adapter, say Y. Otherwise, 304 say N. 305 306 To compile this driver as a module, choose M here: the module 307 will be called a2065. 308 309config HYDRA 310 tristate "Hydra support" 311 depends on ZORRO 312 select CRC32 313 help 314 If you have a Hydra Ethernet adapter, say Y. Otherwise, say N. 315 316 To compile this driver as a module, choose M here: the module 317 will be called hydra. 318 319config ZORRO8390 320 tristate "Zorro NS8390-based Ethernet support" 321 depends on ZORRO 322 select CRC32 323 help 324 This driver is for Zorro Ethernet cards using an NS8390-compatible 325 chipset, like the Village Tronic Ariadne II and the Individual 326 Computers X-Surf Ethernet cards. If you have such a card, say Y. 327 Otherwise, say N. 328 329 To compile this driver as a module, choose M here: the module 330 will be called zorro8390. 331 332config APNE 333 tristate "PCMCIA NE2000 support" 334 depends on AMIGA_PCMCIA 335 select CRC32 336 help 337 If you have a PCMCIA NE2000 compatible adapter, say Y. Otherwise, 338 say N. 339 340 To compile this driver as a module, choose M here: the module 341 will be called apne. 342 343config MAC8390 344 bool "Macintosh NS 8390 based ethernet cards" 345 depends on MAC 346 select CRC32 347 help 348 If you want to include a driver to support Nubus or LC-PDS 349 Ethernet cards using an NS8390 chipset or its equivalent, say Y 350 and read the Ethernet-HOWTO, available from 351 <http://www.tldp.org/docs.html#howto>. 352 353config MAC89x0 354 tristate "Macintosh CS89x0 based ethernet cards" 355 depends on MAC 356 ---help--- 357 Support for CS89x0 chipset based Ethernet cards. If you have a 358 Nubus or LC-PDS network (Ethernet) card of this type, say Y and 359 read the Ethernet-HOWTO, available from 360 <http://www.tldp.org/docs.html#howto>. 361 362 To compile this driver as a module, choose M here. This module will 363 be called mac89x0. 364 365config MACSONIC 366 tristate "Macintosh SONIC based ethernet (onboard, NuBus, LC, CS)" 367 depends on MAC 368 ---help--- 369 Support for NatSemi SONIC based Ethernet devices. This includes 370 the onboard Ethernet in many Quadras as well as some LC-PDS, 371 a few Nubus and all known Comm Slot Ethernet cards. If you have 372 one of these say Y and read the Ethernet-HOWTO, available from 373 <http://www.tldp.org/docs.html#howto>. 374 375 To compile this driver as a module, choose M here. This module will 376 be called macsonic. 377 378config MACMACE 379 bool "Macintosh (AV) onboard MACE ethernet" 380 depends on MAC 381 select CRC32 382 help 383 Support for the onboard AMD 79C940 MACE Ethernet controller used in 384 the 660AV and 840AV Macintosh. If you have one of these Macintoshes 385 say Y and read the Ethernet-HOWTO, available from 386 <http://www.tldp.org/docs.html#howto>. 387 388config MVME147_NET 389 tristate "MVME147 (Lance) Ethernet support" 390 depends on MVME147 391 select CRC32 392 help 393 Support for the on-board Ethernet interface on the Motorola MVME147 394 single-board computer. Say Y here to include the 395 driver for this chip in your kernel. 396 To compile this driver as a module, choose M here. 397 398config MVME16x_NET 399 tristate "MVME16x Ethernet support" 400 depends on MVME16x 401 help 402 This is the driver for the Ethernet interface on the Motorola 403 MVME162, 166, 167, 172 and 177 boards. Say Y here to include the 404 driver for this chip in your kernel. 405 To compile this driver as a module, choose M here. 406 407config BVME6000_NET 408 tristate "BVME6000 Ethernet support" 409 depends on BVME6000 410 help 411 This is the driver for the Ethernet interface on BVME4000 and 412 BVME6000 VME boards. Say Y here to include the driver for this chip 413 in your kernel. 414 To compile this driver as a module, choose M here. 415 416config ATARILANCE 417 tristate "Atari Lance support" 418 depends on ATARI 419 help 420 Say Y to include support for several Atari Ethernet adapters based 421 on the AMD Lance chipset: RieblCard (with or without battery), or 422 PAMCard VME (also the version by Rhotron, with different addresses). 423 424config SUN3LANCE 425 tristate "Sun3/Sun3x on-board LANCE support" 426 depends on SUN3 || SUN3X 427 help 428 Most Sun3 and Sun3x motherboards (including the 3/50, 3/60 and 3/80) 429 featured an AMD Lance 10Mbit Ethernet controller on board; say Y 430 here to compile in the Linux driver for this and enable Ethernet. 431 General Linux information on the Sun 3 and 3x series (now 432 discontinued) is at 433 <http://www.angelfire.com/ca2/tech68k/sun3.html>. 434 435 If you're not building a kernel for a Sun 3, say N. 436 437config SUN3_82586 438 bool "Sun3 on-board Intel 82586 support" 439 depends on SUN3 440 help 441 This driver enables support for the on-board Intel 82586 based 442 Ethernet adapter found on Sun 3/1xx and 3/2xx motherboards. Note 443 that this driver does not support 82586-based adapters on additional 444 VME boards. 445 446config HPLANCE 447 bool "HP on-board LANCE support" 448 depends on DIO 449 select CRC32 450 help 451 If you want to use the builtin "LANCE" Ethernet controller on an 452 HP300 machine, say Y here. 453 454config LASI_82596 455 tristate "Lasi ethernet" 456 depends on GSC 457 help 458 Say Y here to support the builtin Intel 82596 ethernet controller 459 found in Hewlett-Packard PA-RISC machines with 10Mbit ethernet. 460 461config SNI_82596 462 tristate "SNI RM ethernet" 463 depends on NET_ETHERNET && SNI_RM 464 help 465 Say Y here to support the on-board Intel 82596 ethernet controller 466 built into SNI RM machines. 467 468config KORINA 469 tristate "Korina (IDT RC32434) Ethernet support" 470 depends on NET_ETHERNET && MIKROTIK_RB532 471 help 472 If you have a Mikrotik RouterBoard 500 or IDT RC32434 473 based system say Y. Otherwise say N. 474 475config MIPS_JAZZ_SONIC 476 tristate "MIPS JAZZ onboard SONIC Ethernet support" 477 depends on MACH_JAZZ 478 help 479 This is the driver for the onboard card of MIPS Magnum 4000, 480 Acer PICA, Olivetti M700-10 and a few other identical OEM systems. 481 482config XTENSA_XT2000_SONIC 483 tristate "Xtensa XT2000 onboard SONIC Ethernet support" 484 depends on XTENSA_PLATFORM_XT2000 485 help 486 This is the driver for the onboard card of the Xtensa XT2000 board. 487 488config MIPS_AU1X00_ENET 489 tristate "MIPS AU1000 Ethernet support" 490 depends on MIPS_ALCHEMY 491 select PHYLIB 492 select CRC32 493 help 494 If you have an Alchemy Semi AU1X00 based system 495 say Y. Otherwise, say N. 496 497config SGI_IOC3_ETH 498 bool "SGI IOC3 Ethernet" 499 depends on PCI && SGI_IP27 500 select CRC32 501 select MII 502 help 503 If you have a network (Ethernet) card of this type, say Y and read 504 the Ethernet-HOWTO, available from 505 <http://www.tldp.org/docs.html#howto>. 506 507config MIPS_SIM_NET 508 tristate "MIPS simulator Network device" 509 depends on MIPS_SIM 510 help 511 The MIPSNET device is a simple Ethernet network device which is 512 emulated by the MIPS Simulator. 513 If you are not using a MIPSsim or are unsure, say N. 514 515config SGI_O2MACE_ETH 516 tristate "SGI O2 MACE Fast Ethernet support" 517 depends on SGI_IP32=y 518 519config STNIC 520 tristate "National DP83902AV support" 521 depends on SUPERH 522 select CRC32 523 help 524 Support for cards based on the National Semiconductor DP83902AV 525 ST-NIC Serial Network Interface Controller for Twisted Pair. This 526 is a 10Mbit/sec Ethernet controller. Product overview and specs at 527 <http://www.national.com/pf/DP/DP83902A.html>. 528 529 If unsure, say N. 530 531config SH_ETH 532 tristate "Renesas SuperH Ethernet support" 533 depends on SUPERH && \ 534 (CPU_SUBTYPE_SH7710 || CPU_SUBTYPE_SH7712 || \ 535 CPU_SUBTYPE_SH7763 || CPU_SUBTYPE_SH7619 || \ 536 CPU_SUBTYPE_SH7724 || CPU_SUBTYPE_SH7757) 537 select CRC32 538 select MII 539 select MDIO_BITBANG 540 select PHYLIB 541 help 542 Renesas SuperH Ethernet device driver. 543 This driver supporting CPUs are: 544 - SH7710, SH7712, SH7763, SH7619, SH7724, and SH7757. 545 546config SUNLANCE 547 tristate "Sun LANCE support" 548 depends on SBUS 549 select CRC32 550 help 551 This driver supports the "le" interface present on all 32-bit Sparc 552 systems, on some older Ultra systems and as an Sbus option. These 553 cards are based on the AMD Lance chipset, which is better known 554 via the NE2100 cards. 555 556 To compile this driver as a module, choose M here: the module 557 will be called sunlance. 558 559config HAPPYMEAL 560 tristate "Sun Happy Meal 10/100baseT support" 561 depends on SBUS || PCI 562 select CRC32 563 help 564 This driver supports the "hme" interface present on most Ultra 565 systems and as an option on older Sbus systems. This driver supports 566 both PCI and Sbus devices. This driver also supports the "qfe" quad 567 100baseT device available in both PCI and Sbus configurations. 568 569 To compile this driver as a module, choose M here: the module 570 will be called sunhme. 571 572config SUNBMAC 573 tristate "Sun BigMAC 10/100baseT support (EXPERIMENTAL)" 574 depends on SBUS && EXPERIMENTAL 575 select CRC32 576 help 577 This driver supports the "be" interface available as an Sbus option. 578 This is Sun's older 100baseT Ethernet device. 579 580 To compile this driver as a module, choose M here: the module 581 will be called sunbmac. 582 583config SUNQE 584 tristate "Sun QuadEthernet support" 585 depends on SBUS 586 select CRC32 587 help 588 This driver supports the "qe" 10baseT Ethernet device, available as 589 an Sbus option. Note that this is not the same as Quad FastEthernet 590 "qfe" which is supported by the Happy Meal driver instead. 591 592 To compile this driver as a module, choose M here: the module 593 will be called sunqe. 594 595config SUNGEM 596 tristate "Sun GEM support" 597 depends on PCI 598 select CRC32 599 help 600 Support for the Sun GEM chip, aka Sun GigabitEthernet/P 2.0. See also 601 <http://www.sun.com/products-n-solutions/hardware/docs/pdf/806-3985-10.pdf>. 602 603config CASSINI 604 tristate "Sun Cassini support" 605 depends on PCI 606 select CRC32 607 help 608 Support for the Sun Cassini chip, aka Sun GigaSwift Ethernet. See also 609 <http://www.sun.com/products-n-solutions/hardware/docs/pdf/817-4341-10.pdf> 610 611config SUNVNET 612 tristate "Sun Virtual Network support" 613 depends on SUN_LDOMS 614 help 615 Support for virtual network devices under Sun Logical Domains. 616 617config NET_VENDOR_3COM 618 bool "3COM cards" 619 depends on ISA || EISA || MCA || PCI 620 help 621 If you have a network (Ethernet) card belonging to this class, say Y 622 and read the Ethernet-HOWTO, available from 623 <http://www.tldp.org/docs.html#howto>. 624 625 Note that the answer to this question doesn't directly affect the 626 kernel: saying N will just cause the configurator to skip all 627 the questions about 3COM cards. If you say Y, you will be asked for 628 your specific card in the following questions. 629 630config EL1 631 tristate "3c501 \"EtherLink\" support" 632 depends on NET_VENDOR_3COM && ISA 633 ---help--- 634 If you have a network (Ethernet) card of this type, say Y and read 635 the Ethernet-HOWTO, available from 636 <http://www.tldp.org/docs.html#howto>. Also, consider buying a 637 new card, since the 3c501 is slow, broken, and obsolete: you will 638 have problems. Some people suggest to ping ("man ping") a nearby 639 machine every minute ("man cron") when using this card. 640 641 To compile this driver as a module, choose M here. The module 642 will be called 3c501. 643 644config EL2 645 tristate "3c503 \"EtherLink II\" support" 646 depends on NET_VENDOR_3COM && ISA 647 select CRC32 648 help 649 If you have a network (Ethernet) card of this type, say Y and read 650 the Ethernet-HOWTO, available from 651 <http://www.tldp.org/docs.html#howto>. 652 653 To compile this driver as a module, choose M here. The module 654 will be called 3c503. 655 656config ELPLUS 657 tristate "3c505 \"EtherLink Plus\" support" 658 depends on NET_VENDOR_3COM && ISA && ISA_DMA_API 659 ---help--- 660 Information about this network (Ethernet) card can be found in 661 <file:Documentation/networking/3c505.txt>. If you have a card of 662 this type, say Y and read the Ethernet-HOWTO, available from 663 <http://www.tldp.org/docs.html#howto>. 664 665 To compile this driver as a module, choose M here. The module 666 will be called 3c505. 667 668config EL16 669 tristate "3c507 \"EtherLink 16\" support (EXPERIMENTAL)" 670 depends on NET_VENDOR_3COM && ISA && EXPERIMENTAL 671 help 672 If you have a network (Ethernet) card of this type, say Y and read 673 the Ethernet-HOWTO, available from 674 <http://www.tldp.org/docs.html#howto>. 675 676 To compile this driver as a module, choose M here. The module 677 will be called 3c507. 678 679config EL3 680 tristate "3c509/3c529 (MCA)/3c579 \"EtherLink III\" support" 681 depends on NET_VENDOR_3COM && (ISA || EISA || MCA) 682 ---help--- 683 If you have a network (Ethernet) card belonging to the 3Com 684 EtherLinkIII series, say Y and read the Ethernet-HOWTO, available 685 from <http://www.tldp.org/docs.html#howto>. 686 687 If your card is not working you may need to use the DOS 688 setup disk to disable Plug & Play mode, and to select the default 689 media type. 690 691 To compile this driver as a module, choose M here. The module 692 will be called 3c509. 693 694config 3C515 695 tristate "3c515 ISA \"Fast EtherLink\"" 696 depends on NET_VENDOR_3COM && (ISA || EISA) && ISA_DMA_API 697 help 698 If you have a 3Com ISA EtherLink XL "Corkscrew" 3c515 Fast Ethernet 699 network card, say Y and read the Ethernet-HOWTO, available from 700 <http://www.tldp.org/docs.html#howto>. 701 702 To compile this driver as a module, choose M here. The module 703 will be called 3c515. 704 705config ELMC 706 tristate "3c523 \"EtherLink/MC\" support" 707 depends on NET_VENDOR_3COM && MCA_LEGACY 708 help 709 If you have a network (Ethernet) card of this type, say Y and read 710 the Ethernet-HOWTO, available from 711 <http://www.tldp.org/docs.html#howto>. 712 713 To compile this driver as a module, choose M here. The module 714 will be called 3c523. 715 716config ELMC_II 717 tristate "3c527 \"EtherLink/MC 32\" support (EXPERIMENTAL)" 718 depends on NET_VENDOR_3COM && MCA && MCA_LEGACY 719 help 720 If you have a network (Ethernet) card of this type, say Y and read 721 the Ethernet-HOWTO, available from 722 <http://www.tldp.org/docs.html#howto>. 723 724 To compile this driver as a module, choose M here. The module 725 will be called 3c527. 726 727config VORTEX 728 tristate "3c590/3c900 series (592/595/597) \"Vortex/Boomerang\" support" 729 depends on NET_VENDOR_3COM && (PCI || EISA) 730 select MII 731 ---help--- 732 This option enables driver support for a large number of 10Mbps and 733 10/100Mbps EISA, PCI and PCMCIA 3Com network cards: 734 735 "Vortex" (Fast EtherLink 3c590/3c592/3c595/3c597) EISA and PCI 736 "Boomerang" (EtherLink XL 3c900 or 3c905) PCI 737 "Cyclone" (3c540/3c900/3c905/3c980/3c575/3c656) PCI and Cardbus 738 "Tornado" (3c905) PCI 739 "Hurricane" (3c555/3cSOHO) PCI 740 741 If you have such a card, say Y and read the Ethernet-HOWTO, 742 available from <http://www.tldp.org/docs.html#howto>. More 743 specific information is in 744 <file:Documentation/networking/vortex.txt> and in the comments at 745 the beginning of <file:drivers/net/3c59x.c>. 746 747 To compile this support as a module, choose M here. 748 749config TYPHOON 750 tristate "3cr990 series \"Typhoon\" support" 751 depends on NET_VENDOR_3COM && PCI 752 select CRC32 753 ---help--- 754 This option enables driver support for the 3cr990 series of cards: 755 756 3C990-TX, 3CR990-TX-95, 3CR990-TX-97, 3CR990-FX-95, 3CR990-FX-97, 757 3CR990SVR, 3CR990SVR95, 3CR990SVR97, 3CR990-FX-95 Server, 758 3CR990-FX-97 Server, 3C990B-TX-M, 3C990BSVR 759 760 If you have a network (Ethernet) card of this type, say Y and read 761 the Ethernet-HOWTO, available from 762 <http://www.tldp.org/docs.html#howto>. 763 764 To compile this driver as a module, choose M here. The module 765 will be called typhoon. 766 767config LANCE 768 tristate "AMD LANCE and PCnet (AT1500 and NE2100) support" 769 depends on ISA && ISA_DMA_API 770 help 771 If you have a network (Ethernet) card of this type, say Y and read 772 the Ethernet-HOWTO, available from 773 <http://www.tldp.org/docs.html#howto>. Some LinkSys cards are 774 of this type. 775 776 To compile this driver as a module, choose M here: the module 777 will be called lance. This is recommended. 778 779config NET_VENDOR_SMC 780 bool "Western Digital/SMC cards" 781 depends on ISA || MCA || EISA || MAC 782 help 783 If you have a network (Ethernet) card belonging to this class, say Y 784 and read the Ethernet-HOWTO, available from 785 <http://www.tldp.org/docs.html#howto>. 786 787 Note that the answer to this question doesn't directly affect the 788 kernel: saying N will just cause the configurator to skip all 789 the questions about Western Digital cards. If you say Y, you will be 790 asked for your specific card in the following questions. 791 792config WD80x3 793 tristate "WD80*3 support" 794 depends on NET_VENDOR_SMC && ISA 795 select CRC32 796 help 797 If you have a network (Ethernet) card of this type, say Y and read 798 the Ethernet-HOWTO, available from 799 <http://www.tldp.org/docs.html#howto>. 800 801 To compile this driver as a module, choose M here. The module 802 will be called wd. 803 804config ULTRAMCA 805 tristate "SMC Ultra MCA support" 806 depends on NET_VENDOR_SMC && MCA 807 select CRC32 808 help 809 If you have a network (Ethernet) card of this type and are running 810 an MCA based system (PS/2), say Y and read the Ethernet-HOWTO, 811 available from <http://www.tldp.org/docs.html#howto>. 812 813 To compile this driver as a module, choose M here. The module 814 will be called smc-mca. 815 816config ULTRA 817 tristate "SMC Ultra support" 818 depends on NET_VENDOR_SMC && ISA 819 select CRC32 820 ---help--- 821 If you have a network (Ethernet) card of this type, say Y and read 822 the Ethernet-HOWTO, available from 823 <http://www.tldp.org/docs.html#howto>. 824 825 Important: There have been many reports that, with some motherboards 826 mixing an SMC Ultra and an Adaptec AHA154x SCSI card (or compatible, 827 such as some BusLogic models) causes corruption problems with many 828 operating systems. The Linux smc-ultra driver has a work-around for 829 this but keep it in mind if you have such a SCSI card and have 830 problems. 831 832 To compile this driver as a module, choose M here. The module 833 will be called smc-ultra. 834 835config ULTRA32 836 tristate "SMC Ultra32 EISA support" 837 depends on NET_VENDOR_SMC && EISA 838 select CRC32 839 help 840 If you have a network (Ethernet) card of this type, say Y and read 841 the Ethernet-HOWTO, available from 842 <http://www.tldp.org/docs.html#howto>. 843 844 To compile this driver as a module, choose M here. The module 845 will be called smc-ultra32. 846 847config BFIN_MAC 848 tristate "Blackfin on-chip MAC support" 849 depends on NET_ETHERNET && (BF516 || BF518 || BF526 || BF527 || BF536 || BF537) 850 select CRC32 851 select MII 852 select PHYLIB 853 select BFIN_MAC_USE_L1 if DMA_UNCACHED_NONE 854 help 855 This is the driver for Blackfin on-chip mac device. Say Y if you want it 856 compiled into the kernel. This driver is also available as a module 857 ( = code which can be inserted in and removed from the running kernel 858 whenever you want). The module will be called bfin_mac. 859 860config BFIN_MAC_USE_L1 861 bool "Use L1 memory for rx/tx packets" 862 depends on BFIN_MAC && (BF527 || BF537) 863 default y 864 help 865 To get maximum network performance, you should use L1 memory as rx/tx buffers. 866 Say N here if you want to reserve L1 memory for other uses. 867 868config BFIN_TX_DESC_NUM 869 int "Number of transmit buffer packets" 870 depends on BFIN_MAC 871 range 6 10 if BFIN_MAC_USE_L1 872 range 10 100 873 default "10" 874 help 875 Set the number of buffer packets used in driver. 876 877config BFIN_RX_DESC_NUM 878 int "Number of receive buffer packets" 879 depends on BFIN_MAC 880 range 20 100 if BFIN_MAC_USE_L1 881 range 20 800 882 default "20" 883 help 884 Set the number of buffer packets used in driver. 885 886config BFIN_MAC_USE_HWSTAMP 887 bool "Use IEEE 1588 hwstamp" 888 depends on BFIN_MAC && BF518 889 default y 890 help 891 To support the IEEE 1588 Precision Time Protocol (PTP), select y here 892 893config SMC9194 894 tristate "SMC 9194 support" 895 depends on NET_VENDOR_SMC && (ISA || MAC && BROKEN) 896 select CRC32 897 ---help--- 898 This is support for the SMC9xxx based Ethernet cards. Choose this 899 option if you have a DELL laptop with the docking station, or 900 another SMC9192/9194 based chipset. Say Y if you want it compiled 901 into the kernel, and read the file 902 <file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO, 903 available from <http://www.tldp.org/docs.html#howto>. 904 905 To compile this driver as a module, choose M here. The module 906 will be called smc9194. 907 908config SMC91X 909 tristate "SMC 91C9x/91C1xxx support" 910 select CRC32 911 select MII 912 depends on ARM || M32R || SUPERH || \ 913 MIPS || BLACKFIN || MN10300 || COLDFIRE 914 help 915 This is a driver for SMC's 91x series of Ethernet chipsets, 916 including the SMC91C94 and the SMC91C111. Say Y if you want it 917 compiled into the kernel, and read the file 918 <file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO, 919 available from <http://www.tldp.org/docs.html#howto>. 920 921 This driver is also available as a module ( = code which can be 922 inserted in and removed from the running kernel whenever you want). 923 The module will be called smc91x. If you want to compile it as a 924 module, say M here and read <file:Documentation/kbuild/modules.txt>. 925 926config PXA168_ETH 927 tristate "Marvell pxa168 ethernet support" 928 depends on CPU_PXA168 929 select PHYLIB 930 help 931 This driver supports the pxa168 Ethernet ports. 932 933 To compile this driver as a module, choose M here. The module 934 will be called pxa168_eth. 935 936config NET_NETX 937 tristate "NetX Ethernet support" 938 select MII 939 depends on ARCH_NETX 940 help 941 This is support for the Hilscher netX builtin Ethernet ports 942 943 To compile this driver as a module, choose M here. The module 944 will be called netx-eth. 945 946config TI_DAVINCI_EMAC 947 tristate "TI DaVinci EMAC Support" 948 depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 ) 949 select TI_DAVINCI_MDIO 950 select TI_DAVINCI_CPDMA 951 select PHYLIB 952 help 953 This driver supports TI's DaVinci Ethernet . 954 955 To compile this driver as a module, choose M here: the module 956 will be called davinci_emac_driver. This is recommended. 957 958config TI_DAVINCI_MDIO 959 tristate "TI DaVinci MDIO Support" 960 depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 ) 961 select PHYLIB 962 help 963 This driver supports TI's DaVinci MDIO module. 964 965 To compile this driver as a module, choose M here: the module 966 will be called davinci_mdio. This is recommended. 967 968config TI_DAVINCI_CPDMA 969 tristate "TI DaVinci CPDMA Support" 970 depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 ) 971 help 972 This driver supports TI's DaVinci CPDMA dma engine. 973 974 To compile this driver as a module, choose M here: the module 975 will be called davinci_cpdma. This is recommended. 976 977config DM9000 978 tristate "DM9000 support" 979 depends on ARM || BLACKFIN || MIPS 980 select CRC32 981 select MII 982 ---help--- 983 Support for DM9000 chipset. 984 985 To compile this driver as a module, choose M here. The module 986 will be called dm9000. 987 988config DM9000_DEBUGLEVEL 989 int "DM9000 maximum debug level" 990 depends on DM9000 991 default 4 992 help 993 The maximum level of debugging code compiled into the DM9000 994 driver. 995 996config DM9000_FORCE_SIMPLE_PHY_POLL 997 bool "Force simple NSR based PHY polling" 998 depends on DM9000 999 ---help--- 1000 This configuration forces the DM9000 to use the NSR's LinkStatus 1001 bit to determine if the link is up or down instead of the more 1002 costly MII PHY reads. Note, this will not work if the chip is 1003 operating with an external PHY. 1004 1005config ENC28J60 1006 tristate "ENC28J60 support" 1007 depends on EXPERIMENTAL && SPI && NET_ETHERNET 1008 select CRC32 1009 ---help--- 1010 Support for the Microchip EN28J60 ethernet chip. 1011 1012 To compile this driver as a module, choose M here. The module will be 1013 called enc28j60. 1014 1015config ENC28J60_WRITEVERIFY 1016 bool "Enable write verify" 1017 depends on ENC28J60 1018 ---help--- 1019 Enable the verify after the buffer write useful for debugging purpose. 1020 If unsure, say N. 1021 1022config ETHOC 1023 tristate "OpenCores 10/100 Mbps Ethernet MAC support" 1024 depends on NET_ETHERNET && HAS_IOMEM && HAS_DMA 1025 select MII 1026 select PHYLIB 1027 select CRC32 1028 select BITREVERSE 1029 help 1030 Say Y here if you want to use the OpenCores 10/100 Mbps Ethernet MAC. 1031 1032config GRETH 1033 tristate "Aeroflex Gaisler GRETH Ethernet MAC support" 1034 depends on SPARC 1035 select PHYLIB 1036 select CRC32 1037 help 1038 Say Y here if you want to use the Aeroflex Gaisler GRETH Ethernet MAC. 1039 1040config SMC911X 1041 tristate "SMSC LAN911[5678] support" 1042 select CRC32 1043 select MII 1044 depends on ARM || SUPERH || MN10300 1045 help 1046 This is a driver for SMSC's LAN911x series of Ethernet chipsets 1047 including the new LAN9115, LAN9116, LAN9117, and LAN9118. 1048 Say Y if you want it compiled into the kernel, 1049 and read the Ethernet-HOWTO, available from 1050 <http://www.tldp.org/docs.html#howto>. 1051 1052 This driver is also available as a module. The module will be 1053 called smc911x. If you want to compile it as a module, say M 1054 here and read <file:Documentation/kbuild/modules.txt> 1055 1056config SMSC911X 1057 tristate "SMSC LAN911x/LAN921x families embedded ethernet support" 1058 depends on ARM || SUPERH || BLACKFIN || MIPS || MN10300 1059 select CRC32 1060 select MII 1061 select PHYLIB 1062 ---help--- 1063 Say Y here if you want support for SMSC LAN911x and LAN921x families 1064 of ethernet controllers. 1065 1066 To compile this driver as a module, choose M here and read 1067 <file:Documentation/networking/net-modules.txt>. The module 1068 will be called smsc911x. 1069 1070config SMSC911X_ARCH_HOOKS 1071 def_bool n 1072 depends on SMSC911X 1073 help 1074 If the arch enables this, it allows the arch to implement various 1075 hooks for more comprehensive interrupt control and also to override 1076 the source of the MAC address. 1077 1078config NET_VENDOR_RACAL 1079 bool "Racal-Interlan (Micom) NI cards" 1080 depends on ISA 1081 help 1082 If you have a network (Ethernet) card belonging to this class, such 1083 as the NI5010, NI5210 or NI6210, say Y and read the Ethernet-HOWTO, 1084 available from <http://www.tldp.org/docs.html#howto>. 1085 1086 Note that the answer to this question doesn't directly affect the 1087 kernel: saying N will just cause the configurator to skip all 1088 the questions about NI cards. If you say Y, you will be asked for 1089 your specific card in the following questions. 1090 1091config NI5010 1092 tristate "NI5010 support (EXPERIMENTAL)" 1093 depends on NET_VENDOR_RACAL && ISA && EXPERIMENTAL && BROKEN_ON_SMP 1094 ---help--- 1095 If you have a network (Ethernet) card of this type, say Y and read 1096 the Ethernet-HOWTO, available from 1097 <http://www.tldp.org/docs.html#howto>. Note that this is still 1098 experimental code. 1099 1100 To compile this driver as a module, choose M here. The module 1101 will be called ni5010. 1102 1103config NI52 1104 tristate "NI5210 support" 1105 depends on NET_VENDOR_RACAL && ISA 1106 help 1107 If you have a network (Ethernet) card of this type, say Y and read 1108 the Ethernet-HOWTO, available from 1109 <http://www.tldp.org/docs.html#howto>. 1110 1111 To compile this driver as a module, choose M here. The module 1112 will be called ni52. 1113 1114config NI65 1115 tristate "NI6510 support" 1116 depends on NET_VENDOR_RACAL && ISA && ISA_DMA_API 1117 help 1118 If you have a network (Ethernet) card of this type, say Y and read 1119 the Ethernet-HOWTO, available from 1120 <http://www.tldp.org/docs.html#howto>. 1121 1122 To compile this driver as a module, choose M here. The module 1123 will be called ni65. 1124 1125config DNET 1126 tristate "Dave ethernet support (DNET)" 1127 depends on NET_ETHERNET && HAS_IOMEM 1128 select PHYLIB 1129 help 1130 The Dave ethernet interface (DNET) is found on Qong Board FPGA. 1131 Say Y to include support for the DNET chip. 1132 1133 To compile this driver as a module, choose M here: the module 1134 will be called dnet. 1135 1136source "drivers/net/tulip/Kconfig" 1137 1138config AT1700 1139 tristate "AT1700/1720 support (EXPERIMENTAL)" 1140 depends on (ISA || MCA_LEGACY) && EXPERIMENTAL 1141 select CRC32 1142 ---help--- 1143 If you have a network (Ethernet) card of this type, say Y and read 1144 the Ethernet-HOWTO, available from 1145 <http://www.tldp.org/docs.html#howto>. 1146 1147 To compile this driver as a module, choose M here. The module 1148 will be called at1700. 1149 1150config DEPCA 1151 tristate "DEPCA, DE10x, DE200, DE201, DE202, DE422 support" 1152 depends on ISA || EISA || MCA 1153 select CRC32 1154 ---help--- 1155 If you have a network (Ethernet) card of this type, say Y and read 1156 the Ethernet-HOWTO, available from 1157 <http://www.tldp.org/docs.html#howto> as well as 1158 <file:drivers/net/depca.c>. 1159 1160 To compile this driver as a module, choose M here. The module 1161 will be called depca. 1162 1163config HP100 1164 tristate "HP 10/100VG PCLAN (ISA, EISA, PCI) support" 1165 depends on ISA || EISA || PCI 1166 help 1167 If you have a network (Ethernet) card of this type, say Y and read 1168 the Ethernet-HOWTO, available from 1169 <http://www.tldp.org/docs.html#howto>. 1170 1171 To compile this driver as a module, choose M here. The module 1172 will be called hp100. 1173 1174config NET_ISA 1175 bool "Other ISA cards" 1176 depends on ISA 1177 ---help--- 1178 If your network (Ethernet) card hasn't been mentioned yet and its 1179 bus system (that's the way the cards talks to the other components 1180 of your computer) is ISA (as opposed to EISA, VLB or PCI), say Y. 1181 Make sure you know the name of your card. Read the Ethernet-HOWTO, 1182 available from <http://www.tldp.org/docs.html#howto>. 1183 1184 If unsure, say Y. 1185 1186 Note that the answer to this question doesn't directly affect the 1187 kernel: saying N will just cause the configurator to skip all 1188 the remaining ISA network card questions. If you say Y, you will be 1189 asked for your specific card in the following questions. 1190 1191config E2100 1192 tristate "Cabletron E21xx support" 1193 depends on NET_ISA 1194 select CRC32 1195 help 1196 If you have a network (Ethernet) card of this type, say Y and read 1197 the Ethernet-HOWTO, available from 1198 <http://www.tldp.org/docs.html#howto>. 1199 1200 To compile this driver as a module, choose M here. The module 1201 will be called e2100. 1202 1203config EWRK3 1204 tristate "EtherWORKS 3 (DE203, DE204, DE205) support" 1205 depends on NET_ISA 1206 select CRC32 1207 ---help--- 1208 This driver supports the DE203, DE204 and DE205 network (Ethernet) 1209 cards. If this is for you, say Y and read 1210 <file:Documentation/networking/ewrk3.txt> in the kernel source as 1211 well as the Ethernet-HOWTO, available from 1212 <http://www.tldp.org/docs.html#howto>. 1213 1214 To compile this driver as a module, choose M here. The module 1215 will be called ewrk3. 1216 1217config EEXPRESS 1218 tristate "EtherExpress 16 support" 1219 depends on NET_ISA 1220 ---help--- 1221 If you have an EtherExpress16 network (Ethernet) card, say Y and 1222 read the Ethernet-HOWTO, available from 1223 <http://www.tldp.org/docs.html#howto>. Note that the Intel 1224 EtherExpress16 card used to be regarded as a very poor choice 1225 because the driver was very unreliable. We now have a new driver 1226 that should do better. 1227 1228 To compile this driver as a module, choose M here. The module 1229 will be called eexpress. 1230 1231config EEXPRESS_PRO 1232 tristate "EtherExpressPro support/EtherExpress 10 (i82595) support" 1233 depends on NET_ISA 1234 ---help--- 1235 If you have a network (Ethernet) card of this type, say Y. This 1236 driver supports Intel i82595{FX,TX} based boards. Note however 1237 that the EtherExpress PRO/100 Ethernet card has its own separate 1238 driver. Please read the Ethernet-HOWTO, available from 1239 <http://www.tldp.org/docs.html#howto>. 1240 1241 To compile this driver as a module, choose M here. The module 1242 will be called eepro. 1243 1244config HPLAN_PLUS 1245 tristate "HP PCLAN+ (27247B and 27252A) support" 1246 depends on NET_ISA 1247 select CRC32 1248 help 1249 If you have a network (Ethernet) card of this type, say Y and read 1250 the Ethernet-HOWTO, available from 1251 <http://www.tldp.org/docs.html#howto>. 1252 1253 To compile this driver as a module, choose M here. The module 1254 will be called hp-plus. 1255 1256config HPLAN 1257 tristate "HP PCLAN (27245 and other 27xxx series) support" 1258 depends on NET_ISA 1259 select CRC32 1260 help 1261 If you have a network (Ethernet) card of this type, say Y and read 1262 the Ethernet-HOWTO, available from 1263 <http://www.tldp.org/docs.html#howto>. 1264 1265 To compile this driver as a module, choose M here. The module 1266 will be called hp. 1267 1268config LP486E 1269 tristate "LP486E on board Ethernet" 1270 depends on NET_ISA 1271 help 1272 Say Y here to support the 82596-based on-board Ethernet controller 1273 for the Panther motherboard, which is one of the two shipped in the 1274 Intel Professional Workstation. 1275 1276config ETH16I 1277 tristate "ICL EtherTeam 16i/32 support" 1278 depends on NET_ISA 1279 help 1280 If you have a network (Ethernet) card of this type, say Y and read 1281 the Ethernet-HOWTO, available from 1282 <http://www.tldp.org/docs.html#howto>. 1283 1284 To compile this driver as a module, choose M here. The module 1285 will be called eth16i. 1286 1287config NE2000 1288 tristate "NE2000/NE1000 support" 1289 depends on NET_ISA || (Q40 && m) || M32R || MACH_TX49XX 1290 select CRC32 1291 ---help--- 1292 If you have a network (Ethernet) card of this type, say Y and read 1293 the Ethernet-HOWTO, available from 1294 <http://www.tldp.org/docs.html#howto>. Many Ethernet cards 1295 without a specific driver are compatible with NE2000. 1296 1297 If you have a PCI NE2000 card however, say N here and Y to "PCI 1298 NE2000 and clone support" under "EISA, VLB, PCI and on board 1299 controllers" below. If you have a NE2000 card and are running on 1300 an MCA system (a bus system used on some IBM PS/2 computers and 1301 laptops), say N here and Y to "NE/2 (ne2000 MCA version) support", 1302 below. 1303 1304 To compile this driver as a module, choose M here. The module 1305 will be called ne. 1306 1307config ZNET 1308 tristate "Zenith Z-Note support (EXPERIMENTAL)" 1309 depends on NET_ISA && EXPERIMENTAL && ISA_DMA_API 1310 help 1311 The Zenith Z-Note notebook computer has a built-in network 1312 (Ethernet) card, and this is the Linux driver for it. Note that the 1313 IBM Thinkpad 300 is compatible with the Z-Note and is also supported 1314 by this driver. Read the Ethernet-HOWTO, available from 1315 <http://www.tldp.org/docs.html#howto>. 1316 1317config SEEQ8005 1318 tristate "SEEQ8005 support (EXPERIMENTAL)" 1319 depends on NET_ISA && EXPERIMENTAL 1320 help 1321 This is a driver for the SEEQ 8005 network (Ethernet) card. If this 1322 is for you, read the Ethernet-HOWTO, available from 1323 <http://www.tldp.org/docs.html#howto>. 1324 1325 To compile this driver as a module, choose M here. The module 1326 will be called seeq8005. 1327 1328config NE2_MCA 1329 tristate "NE/2 (ne2000 MCA version) support" 1330 depends on MCA_LEGACY 1331 select CRC32 1332 help 1333 If you have a network (Ethernet) card of this type, say Y and read 1334 the Ethernet-HOWTO, available from 1335 <http://www.tldp.org/docs.html#howto>. 1336 1337 To compile this driver as a module, choose M here. The module 1338 will be called ne2. 1339 1340config IBMLANA 1341 tristate "IBM LAN Adapter/A support" 1342 depends on MCA 1343 ---help--- 1344 This is a Micro Channel Ethernet adapter. You need to set 1345 CONFIG_MCA to use this driver. It is both available as an in-kernel 1346 driver and as a module. 1347 1348 To compile this driver as a module, choose M here. The only 1349 currently supported card is the IBM LAN Adapter/A for Ethernet. It 1350 will both support 16K and 32K memory windows, however a 32K window 1351 gives a better security against packet losses. Usage of multiple 1352 boards with this driver should be possible, but has not been tested 1353 up to now due to lack of hardware. 1354 1355config IBMVETH 1356 tristate "IBM LAN Virtual Ethernet support" 1357 depends on PPC_PSERIES 1358 ---help--- 1359 This driver supports virtual ethernet adapters on newer IBM iSeries 1360 and pSeries systems. 1361 1362 To compile this driver as a module, choose M here. The module will 1363 be called ibmveth. 1364 1365source "drivers/net/ibm_newemac/Kconfig" 1366 1367config NET_PCI 1368 bool "EISA, VLB, PCI and on board controllers" 1369 depends on ISA || EISA || PCI 1370 help 1371 This is another class of network cards which attach directly to the 1372 bus. If you have one of those, say Y and read the Ethernet-HOWTO, 1373 available from <http://www.tldp.org/docs.html#howto>. 1374 1375 Note that the answer to this question doesn't directly affect the 1376 kernel: saying N will just cause the configurator to skip all 1377 the questions about this class of network cards. If you say Y, you 1378 will be asked for your specific card in the following questions. If 1379 you are unsure, say Y. 1380 1381config PCNET32 1382 tristate "AMD PCnet32 PCI support" 1383 depends on NET_PCI && PCI 1384 select CRC32 1385 select MII 1386 help 1387 If you have a PCnet32 or PCnetPCI based network (Ethernet) card, 1388 answer Y here and read the Ethernet-HOWTO, available from 1389 <http://www.tldp.org/docs.html#howto>. 1390 1391 To compile this driver as a module, choose M here. The module 1392 will be called pcnet32. 1393 1394config AMD8111_ETH 1395 tristate "AMD 8111 (new PCI lance) support" 1396 depends on NET_PCI && PCI 1397 select CRC32 1398 select MII 1399 help 1400 If you have an AMD 8111-based PCI lance ethernet card, 1401 answer Y here and read the Ethernet-HOWTO, available from 1402 <http://www.tldp.org/docs.html#howto>. 1403 1404 To compile this driver as a module, choose M here. The module 1405 will be called amd8111e. 1406 1407config ADAPTEC_STARFIRE 1408 tristate "Adaptec Starfire/DuraLAN support" 1409 depends on NET_PCI && PCI 1410 select CRC32 1411 select MII 1412 help 1413 Say Y here if you have an Adaptec Starfire (or DuraLAN) PCI network 1414 adapter. The DuraLAN chip is used on the 64 bit PCI boards from 1415 Adaptec e.g. the ANA-6922A. The older 32 bit boards use the tulip 1416 driver. 1417 1418 To compile this driver as a module, choose M here: the module 1419 will be called starfire. This is recommended. 1420 1421config AC3200 1422 tristate "Ansel Communications EISA 3200 support (EXPERIMENTAL)" 1423 depends on NET_PCI && (ISA || EISA) && EXPERIMENTAL 1424 select CRC32 1425 help 1426 If you have a network (Ethernet) card of this type, say Y and read 1427 the Ethernet-HOWTO, available from 1428 <http://www.tldp.org/docs.html#howto>. 1429 1430 To compile this driver as a module, choose M here. The module 1431 will be called ac3200. 1432 1433config KSZ884X_PCI 1434 tristate "Micrel KSZ8841/2 PCI" 1435 depends on NET_PCI && PCI 1436 select MII 1437 select CRC32 1438 help 1439 This PCI driver is for Micrel KSZ8841/KSZ8842 PCI Ethernet chip. 1440 1441 To compile this driver as a module, choose M here. The module 1442 will be called ksz884x. 1443 1444config APRICOT 1445 tristate "Apricot Xen-II on board Ethernet" 1446 depends on NET_PCI && ISA 1447 help 1448 If you have a network (Ethernet) controller of this type, say Y and 1449 read the Ethernet-HOWTO, available from 1450 <http://www.tldp.org/docs.html#howto>. 1451 1452 To compile this driver as a module, choose M here. The module 1453 will be called apricot. 1454 1455config B44 1456 tristate "Broadcom 440x/47xx ethernet support" 1457 depends on SSB_POSSIBLE && HAS_DMA 1458 select SSB 1459 select MII 1460 help 1461 If you have a network (Ethernet) controller of this type, say Y 1462 or M and read the Ethernet-HOWTO, available from 1463 <http://www.tldp.org/docs.html#howto>. 1464 1465 To compile this driver as a module, choose M here. The module 1466 will be called b44. 1467 1468# Auto-select SSB PCI-HOST support, if possible 1469config B44_PCI_AUTOSELECT 1470 bool 1471 depends on B44 && SSB_PCIHOST_POSSIBLE 1472 select SSB_PCIHOST 1473 default y 1474 1475# Auto-select SSB PCICORE driver, if possible 1476config B44_PCICORE_AUTOSELECT 1477 bool 1478 depends on B44 && SSB_DRIVER_PCICORE_POSSIBLE 1479 select SSB_DRIVER_PCICORE 1480 default y 1481 1482config B44_PCI 1483 bool 1484 depends on B44_PCI_AUTOSELECT && B44_PCICORE_AUTOSELECT 1485 default y 1486 1487config FORCEDETH 1488 tristate "nForce Ethernet support" 1489 depends on NET_PCI && PCI 1490 help 1491 If you have a network (Ethernet) controller of this type, say Y and 1492 read the Ethernet-HOWTO, available from 1493 <http://www.tldp.org/docs.html#howto>. 1494 1495 To compile this driver as a module, choose M here. The module 1496 will be called forcedeth. 1497 1498config CS89x0 1499 tristate "CS89x0 support" 1500 depends on NET_ETHERNET && (ISA || EISA || MACH_IXDP2351 \ 1501 || ARCH_IXDP2X01 || MACH_MX31ADS || MACH_QQ2440) 1502 ---help--- 1503 Support for CS89x0 chipset based Ethernet cards. If you have a 1504 network (Ethernet) card of this type, say Y and read the 1505 Ethernet-HOWTO, available from 1506 <http://www.tldp.org/docs.html#howto> as well as 1507 <file:Documentation/networking/cs89x0.txt>. 1508 1509 To compile this driver as a module, choose M here. The module 1510 will be called cs89x0. 1511 1512config CS89x0_NONISA_IRQ 1513 def_bool y 1514 depends on CS89x0 != n 1515 depends on MACH_IXDP2351 || ARCH_IXDP2X01 || MACH_MX31ADS || MACH_QQ2440 1516 1517config TC35815 1518 tristate "TOSHIBA TC35815 Ethernet support" 1519 depends on NET_PCI && PCI && MIPS 1520 select PHYLIB 1521 1522config E100 1523 tristate "Intel(R) PRO/100+ support" 1524 depends on NET_PCI && PCI 1525 select MII 1526 ---help--- 1527 This driver supports Intel(R) PRO/100 family of adapters. 1528 To verify that your adapter is supported, find the board ID number 1529 on the adapter. Look for a label that has a barcode and a number 1530 in the format 123456-001 (six digits hyphen three digits). 1531 1532 Use the above information and the Adapter & Driver ID Guide at: 1533 1534 <http://support.intel.com/support/network/adapter/pro100/21397.htm> 1535 1536 to identify the adapter. 1537 1538 For the latest Intel PRO/100 network driver for Linux, see: 1539 1540 <http://www.intel.com/p/en_US/support/highlights/network/pro100plus> 1541 1542 More specific information on configuring the driver is in 1543 <file:Documentation/networking/e100.txt>. 1544 1545 To compile this driver as a module, choose M here. The module 1546 will be called e100. 1547 1548config LNE390 1549 tristate "Mylex EISA LNE390A/B support (EXPERIMENTAL)" 1550 depends on NET_PCI && EISA && EXPERIMENTAL 1551 select CRC32 1552 help 1553 If you have a network (Ethernet) card of this type, say Y and read 1554 the Ethernet-HOWTO, available from 1555 <http://www.tldp.org/docs.html#howto>. 1556 1557 To compile this driver as a module, choose M here. The module 1558 will be called lne390. 1559 1560config FEALNX 1561 tristate "Myson MTD-8xx PCI Ethernet support" 1562 depends on NET_PCI && PCI 1563 select CRC32 1564 select MII 1565 help 1566 Say Y here to support the Myson MTD-800 family of PCI-based Ethernet 1567 cards. <http://www.myson.com.tw/> 1568 1569config NATSEMI 1570 tristate "National Semiconductor DP8381x series PCI Ethernet support" 1571 depends on NET_PCI && PCI 1572 select CRC32 1573 help 1574 This driver is for the National Semiconductor DP83810 series, 1575 which is used in cards from PureData, NetGear, Linksys 1576 and others, including the 83815 chip. 1577 More specific information and updates are available from 1578 <http://www.scyld.com/network/natsemi.html>. 1579 1580config NE2K_PCI 1581 tristate "PCI NE2000 and clones support (see help)" 1582 depends on NET_PCI && PCI 1583 select CRC32 1584 ---help--- 1585 This driver is for NE2000 compatible PCI cards. It will not work 1586 with ISA NE2000 cards (they have their own driver, "NE2000/NE1000 1587 support" below). If you have a PCI NE2000 network (Ethernet) card, 1588 say Y and read the Ethernet-HOWTO, available from 1589 <http://www.tldp.org/docs.html#howto>. 1590 1591 This driver also works for the following NE2000 clone cards: 1592 RealTek RTL-8029 Winbond 89C940 Compex RL2000 KTI ET32P2 1593 NetVin NV5000SC Via 86C926 SureCom NE34 Winbond 1594 Holtek HT80232 Holtek HT80229 1595 1596 To compile this driver as a module, choose M here. The module 1597 will be called ne2k-pci. 1598 1599config NE3210 1600 tristate "Novell/Eagle/Microdyne NE3210 EISA support (EXPERIMENTAL)" 1601 depends on NET_PCI && EISA && EXPERIMENTAL 1602 select CRC32 1603 ---help--- 1604 If you have a network (Ethernet) card of this type, say Y and read 1605 the Ethernet-HOWTO, available from 1606 <http://www.tldp.org/docs.html#howto>. Note that this driver 1607 will NOT WORK for NE3200 cards as they are completely different. 1608 1609 To compile this driver as a module, choose M here. The module 1610 will be called ne3210. 1611 1612config ES3210 1613 tristate "Racal-Interlan EISA ES3210 support (EXPERIMENTAL)" 1614 depends on NET_PCI && EISA && EXPERIMENTAL 1615 select CRC32 1616 help 1617 If you have a network (Ethernet) card of this type, say Y and read 1618 the Ethernet-HOWTO, available from 1619 <http://www.tldp.org/docs.html#howto>. 1620 1621 To compile this driver as a module, choose M here. The module 1622 will be called es3210. 1623 1624config 8139CP 1625 tristate "RealTek RTL-8139 C+ PCI Fast Ethernet Adapter support (EXPERIMENTAL)" 1626 depends on NET_PCI && PCI && EXPERIMENTAL 1627 select CRC32 1628 select MII 1629 help 1630 This is a driver for the Fast Ethernet PCI network cards based on 1631 the RTL8139C+ chips. If you have one of those, say Y and read 1632 the Ethernet-HOWTO, available from 1633 <http://www.tldp.org/docs.html#howto>. 1634 1635 To compile this driver as a module, choose M here: the module 1636 will be called 8139cp. This is recommended. 1637 1638config 8139TOO 1639 tristate "RealTek RTL-8129/8130/8139 PCI Fast Ethernet Adapter support" 1640 depends on NET_PCI && PCI 1641 select CRC32 1642 select MII 1643 ---help--- 1644 This is a driver for the Fast Ethernet PCI network cards based on 1645 the RTL 8129/8130/8139 chips. If you have one of those, say Y and 1646 read the Ethernet-HOWTO <http://www.tldp.org/docs.html#howto>. 1647 1648 To compile this driver as a module, choose M here: the module 1649 will be called 8139too. This is recommended. 1650 1651config 8139TOO_PIO 1652 bool "Use PIO instead of MMIO" 1653 default y 1654 depends on 8139TOO 1655 help 1656 This instructs the driver to use programmed I/O ports (PIO) instead 1657 of PCI shared memory (MMIO). This can possibly solve some problems 1658 in case your mainboard has memory consistency issues. If unsure, 1659 say N. 1660 1661config 8139TOO_TUNE_TWISTER 1662 bool "Support for uncommon RTL-8139 rev. K (automatic channel equalization)" 1663 depends on 8139TOO 1664 help 1665 This implements a function which might come in handy in case you 1666 are using low quality on long cabling. It is required for RealTek 1667 RTL-8139 revision K boards, and totally unused otherwise. It tries 1668 to match the transceiver to the cable characteristics. This is 1669 experimental since hardly documented by the manufacturer. 1670 If unsure, say Y. 1671 1672config 8139TOO_8129 1673 bool "Support for older RTL-8129/8130 boards" 1674 depends on 8139TOO 1675 help 1676 This enables support for the older and uncommon RTL-8129 and 1677 RTL-8130 chips, which support MII via an external transceiver, 1678 instead of an internal one. Disabling this option will save some 1679 memory by making the code size smaller. If unsure, say Y. 1680 1681config 8139_OLD_RX_RESET 1682 bool "Use older RX-reset method" 1683 depends on 8139TOO 1684 help 1685 The 8139too driver was recently updated to contain a more rapid 1686 reset sequence, in the face of severe receive errors. This "new" 1687 RX-reset method should be adequate for all boards. But if you 1688 experience problems, you can enable this option to restore the 1689 old RX-reset behavior. If unsure, say N. 1690 1691config R6040 1692 tristate "RDC R6040 Fast Ethernet Adapter support" 1693 depends on NET_PCI && PCI 1694 select CRC32 1695 select MII 1696 select PHYLIB 1697 help 1698 This is a driver for the R6040 Fast Ethernet MACs found in the 1699 the RDC R-321x System-on-chips. 1700 1701 To compile this driver as a module, choose M here: the module 1702 will be called r6040. This is recommended. 1703 1704config SIS900 1705 tristate "SiS 900/7016 PCI Fast Ethernet Adapter support" 1706 depends on NET_PCI && PCI 1707 select CRC32 1708 select MII 1709 ---help--- 1710 This is a driver for the Fast Ethernet PCI network cards based on 1711 the SiS 900 and SiS 7016 chips. The SiS 900 core is also embedded in 1712 SiS 630 and SiS 540 chipsets. 1713 1714 This driver also supports AMD 79C901 HomePNA so that you can use 1715 your phone line as a network cable. 1716 1717 To compile this driver as a module, choose M here: the module 1718 will be called sis900. This is recommended. 1719 1720config EPIC100 1721 tristate "SMC EtherPower II" 1722 depends on NET_PCI && PCI 1723 select CRC32 1724 select MII 1725 help 1726 This driver is for the SMC EtherPower II 9432 PCI Ethernet NIC, 1727 which is based on the SMC83c17x (EPIC/100). 1728 More specific information and updates are available from 1729 <http://www.scyld.com/network/epic100.html>. 1730 1731config SMSC9420 1732 tristate "SMSC LAN9420 PCI ethernet adapter support" 1733 depends on NET_PCI && PCI 1734 select CRC32 1735 select PHYLIB 1736 select SMSC_PHY 1737 help 1738 This is a driver for SMSC's LAN9420 PCI ethernet adapter. 1739 Say Y if you want it compiled into the kernel, 1740 and read the Ethernet-HOWTO, available from 1741 <http://www.tldp.org/docs.html#howto>. 1742 1743 This driver is also available as a module. The module will be 1744 called smsc9420. If you want to compile it as a module, say M 1745 here and read <file:Documentation/kbuild/modules.txt> 1746 1747config SUNDANCE 1748 tristate "Sundance Alta support" 1749 depends on NET_PCI && PCI 1750 select CRC32 1751 select MII 1752 help 1753 This driver is for the Sundance "Alta" chip. 1754 More specific information and updates are available from 1755 <http://www.scyld.com/network/sundance.html>. 1756 1757config SUNDANCE_MMIO 1758 bool "Use MMIO instead of PIO" 1759 depends on SUNDANCE 1760 help 1761 Enable memory-mapped I/O for interaction with Sundance NIC registers. 1762 Do NOT enable this by default, PIO (enabled when MMIO is disabled) 1763 is known to solve bugs on certain chips. 1764 1765 If unsure, say N. 1766 1767config TLAN 1768 tristate "TI ThunderLAN support" 1769 depends on NET_PCI && (PCI || EISA) 1770 ---help--- 1771 If you have a PCI Ethernet network card based on the ThunderLAN chip 1772 which is supported by this driver, say Y and read the 1773 Ethernet-HOWTO, available from 1774 <http://www.tldp.org/docs.html#howto>. 1775 1776 Devices currently supported by this driver are Compaq Netelligent, 1777 Compaq NetFlex and Olicom cards. Please read the file 1778 <file:Documentation/networking/tlan.txt> for more details. 1779 1780 To compile this driver as a module, choose M here. The module 1781 will be called tlan. 1782 1783 Please email feedback to <torben.mathiasen@compaq.com>. 1784 1785config KS8842 1786 tristate "Micrel KSZ8841/42 with generic bus interface" 1787 depends on HAS_IOMEM && DMA_ENGINE 1788 help 1789 This platform driver is for KSZ8841(1-port) / KS8842(2-port) 1790 ethernet switch chip (managed, VLAN, QoS) from Micrel or 1791 Timberdale(FPGA). 1792 1793config KS8851 1794 tristate "Micrel KS8851 SPI" 1795 depends on SPI 1796 select MII 1797 select CRC32 1798 help 1799 SPI driver for Micrel KS8851 SPI attached network chip. 1800 1801config KS8851_MLL 1802 tristate "Micrel KS8851 MLL" 1803 depends on HAS_IOMEM 1804 select MII 1805 help 1806 This platform driver is for Micrel KS8851 Address/data bus 1807 multiplexed network chip. 1808 1809config VIA_RHINE 1810 tristate "VIA Rhine support" 1811 depends on NET_PCI && PCI 1812 select CRC32 1813 select MII 1814 help 1815 If you have a VIA "Rhine" based network card (Rhine-I (VT86C100A), 1816 Rhine-II (VT6102), or Rhine-III (VT6105)), say Y here. Rhine-type 1817 Ethernet functions can also be found integrated on South Bridges 1818 (e.g. VT8235). 1819 1820 To compile this driver as a module, choose M here. The module 1821 will be called via-rhine. 1822 1823config VIA_RHINE_MMIO 1824 bool "Use MMIO instead of PIO" 1825 depends on VIA_RHINE 1826 help 1827 This instructs the driver to use PCI shared memory (MMIO) instead of 1828 programmed I/O ports (PIO). Enabling this gives an improvement in 1829 processing time in parts of the driver. 1830 1831 If unsure, say Y. 1832 1833config SC92031 1834 tristate "Silan SC92031 PCI Fast Ethernet Adapter driver (EXPERIMENTAL)" 1835 depends on NET_PCI && PCI && EXPERIMENTAL 1836 select CRC32 1837 ---help--- 1838 This is a driver for the Fast Ethernet PCI network cards based on 1839 the Silan SC92031 chip (sometimes also called Rsltek 8139D). If you 1840 have one of these, say Y here. 1841 1842 To compile this driver as a module, choose M here: the module 1843 will be called sc92031. This is recommended. 1844 1845config CPMAC 1846 tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)" 1847 depends on NET_ETHERNET && EXPERIMENTAL && AR7 1848 select PHYLIB 1849 help 1850 TI AR7 CPMAC Ethernet support 1851 1852config NET_POCKET 1853 bool "Pocket and portable adapters" 1854 depends on PARPORT 1855 ---help--- 1856 Cute little network (Ethernet) devices which attach to the parallel 1857 port ("pocket adapters"), commonly used with laptops. If you have 1858 one of those, say Y and read the Ethernet-HOWTO, available from 1859 <http://www.tldp.org/docs.html#howto>. 1860 1861 If you want to plug a network (or some other) card into the PCMCIA 1862 (or PC-card) slot of your laptop instead (PCMCIA is the standard for 1863 credit card size extension cards used by all modern laptops), you 1864 need the pcmcia-cs package (location contained in the file 1865 <file:Documentation/Changes>) and you can say N here. 1866 1867 Laptop users should read the Linux Laptop home page at 1868 <http://www.linux-on-laptops.com/> or 1869 Tuxmobil - Linux on Mobile Computers at <http://www.tuxmobil.org/>. 1870 1871 Note that the answer to this question doesn't directly affect the 1872 kernel: saying N will just cause the configurator to skip all 1873 the questions about this class of network devices. If you say Y, you 1874 will be asked for your specific device in the following questions. 1875 1876config ATP 1877 tristate "AT-LAN-TEC/RealTek pocket adapter support" 1878 depends on NET_POCKET && PARPORT && X86 1879 select CRC32 1880 ---help--- 1881 This is a network (Ethernet) device which attaches to your parallel 1882 port. Read <file:drivers/net/atp.c> as well as the Ethernet-HOWTO, 1883 available from <http://www.tldp.org/docs.html#howto>, if you 1884 want to use this. If you intend to use this driver, you should have 1885 said N to the "Parallel printer support", because the two drivers 1886 don't like each other. 1887 1888 To compile this driver as a module, choose M here: the module 1889 will be called atp. 1890 1891config DE600 1892 tristate "D-Link DE600 pocket adapter support" 1893 depends on NET_POCKET && PARPORT 1894 ---help--- 1895 This is a network (Ethernet) device which attaches to your parallel 1896 port. Read <file:Documentation/networking/DLINK.txt> as well as the 1897 Ethernet-HOWTO, available from 1898 <http://www.tldp.org/docs.html#howto>, if you want to use 1899 this. It is possible to have several devices share a single parallel 1900 port and it is safe to compile the corresponding drivers into the 1901 kernel. 1902 1903 To compile this driver as a module, choose M here: the module 1904 will be called de600. 1905 1906config DE620 1907 tristate "D-Link DE620 pocket adapter support" 1908 depends on NET_POCKET && PARPORT 1909 ---help--- 1910 This is a network (Ethernet) device which attaches to your parallel 1911 port. Read <file:Documentation/networking/DLINK.txt> as well as the 1912 Ethernet-HOWTO, available from 1913 <http://www.tldp.org/docs.html#howto>, if you want to use 1914 this. It is possible to have several devices share a single parallel 1915 port and it is safe to compile the corresponding drivers into the 1916 kernel. 1917 1918 To compile this driver as a module, choose M here: the module 1919 will be called de620. 1920 1921config SGISEEQ 1922 tristate "SGI Seeq ethernet controller support" 1923 depends on SGI_HAS_SEEQ 1924 help 1925 Say Y here if you have an Seeq based Ethernet network card. This is 1926 used in many Silicon Graphics machines. 1927 1928config DECLANCE 1929 tristate "DEC LANCE ethernet controller support" 1930 depends on MACH_DECSTATION 1931 select CRC32 1932 help 1933 This driver is for the series of Ethernet controllers produced by 1934 DEC (now Compaq) based on the AMD Lance chipset, including the 1935 DEPCA series. (This chipset is better known via the NE2100 cards.) 1936 1937config 68360_ENET 1938 bool "Motorola 68360 ethernet controller" 1939 depends on M68360 1940 help 1941 Say Y here if you want to use the built-in ethernet controller of 1942 the Motorola 68360 processor. 1943 1944config FEC 1945 bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)" 1946 depends on M523x || M527x || M5272 || M528x || M520x || M532x || \ 1947 IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC 1948 default IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC if ARM 1949 select PHYLIB 1950 help 1951 Say Y here if you want to use the built-in 10/100 Fast ethernet 1952 controller on some Motorola ColdFire and Freescale i.MX processors. 1953 1954config FEC_MPC52xx 1955 tristate "MPC52xx FEC driver" 1956 depends on PPC_MPC52xx && PPC_BESTCOMM 1957 select CRC32 1958 select PHYLIB 1959 select PPC_BESTCOMM_FEC 1960 ---help--- 1961 This option enables support for the MPC5200's on-chip 1962 Fast Ethernet Controller 1963 If compiled as module, it will be called fec_mpc52xx. 1964 1965config FEC_MPC52xx_MDIO 1966 bool "MPC52xx FEC MDIO bus driver" 1967 depends on FEC_MPC52xx 1968 default y 1969 ---help--- 1970 The MPC5200's FEC can connect to the Ethernet either with 1971 an external MII PHY chip or 10 Mbps 7-wire interface 1972 (Motorola? industry standard). 1973 If your board uses an external PHY connected to FEC, enable this. 1974 If not sure, enable. 1975 If compiled as module, it will be called fec_mpc52xx_phy. 1976 1977config NE_H8300 1978 tristate "NE2000 compatible support for H8/300" 1979 depends on H8300 1980 help 1981 Say Y here if you want to use the NE2000 compatible 1982 controller on the Renesas H8/300 processor. 1983 1984config ATL2 1985 tristate "Atheros L2 Fast Ethernet support" 1986 depends on PCI 1987 select CRC32 1988 select MII 1989 help 1990 This driver supports the Atheros L2 fast ethernet adapter. 1991 1992 To compile this driver as a module, choose M here. The module 1993 will be called atl2. 1994 1995config XILINX_EMACLITE 1996 tristate "Xilinx 10/100 Ethernet Lite support" 1997 depends on PPC32 || MICROBLAZE 1998 select PHYLIB 1999 help 2000 This driver supports the 10/100 Ethernet Lite from Xilinx. 2001 2002config BCM63XX_ENET 2003 tristate "Broadcom 63xx internal mac support" 2004 depends on BCM63XX 2005 select MII 2006 select PHYLIB 2007 help 2008 This driver supports the ethernet MACs in the Broadcom 63xx 2009 MIPS chipset family (BCM63XX). 2010 2011config FTMAC100 2012 tristate "Faraday FTMAC100 10/100 Ethernet support" 2013 depends on ARM 2014 select MII 2015 help 2016 This driver supports the FTMAC100 10/100 Ethernet controller 2017 from Faraday. It is used on Faraday A320, Andes AG101 and some 2018 other ARM/NDS32 SoC's. 2019 2020config LANTIQ_ETOP 2021 tristate "Lantiq SoC ETOP driver" 2022 depends on SOC_TYPE_XWAY 2023 help 2024 Support for the MII0 inside the Lantiq SoC 2025 2026 2027source "drivers/net/fs_enet/Kconfig" 2028 2029source "drivers/net/octeon/Kconfig" 2030 2031endif # NET_ETHERNET 2032 2033# 2034# Gigabit Ethernet 2035# 2036 2037menuconfig NETDEV_1000 2038 bool "Ethernet (1000 Mbit)" 2039 depends on !UML 2040 default y 2041 ---help--- 2042 Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common 2043 type of Local Area Network (LAN) in universities and companies. 2044 2045 Say Y here to get to see options for Gigabit Ethernet drivers. 2046 This option alone does not add any kernel code. 2047 Note that drivers supporting both 100 and 1000 MBit may be listed 2048 under "Ethernet (10 or 100MBit)" instead. 2049 2050 If you say N, all options in this submenu will be skipped and disabled. 2051 2052if NETDEV_1000 2053 2054config ACENIC 2055 tristate "Alteon AceNIC/3Com 3C985/NetGear GA620 Gigabit support" 2056 depends on PCI 2057 ---help--- 2058 Say Y here if you have an Alteon AceNIC, 3Com 3C985(B), NetGear 2059 GA620, SGI Gigabit or Farallon PN9000-SX PCI Gigabit Ethernet 2060 adapter. The driver allows for using the Jumbo Frame option (9000 2061 bytes/frame) however it requires that your switches can handle this 2062 as well. To enable Jumbo Frames, add `mtu 9000' to your ifconfig 2063 line. 2064 2065 To compile this driver as a module, choose M here: the 2066 module will be called acenic. 2067 2068config ACENIC_OMIT_TIGON_I 2069 bool "Omit support for old Tigon I based AceNICs" 2070 depends on ACENIC 2071 help 2072 Say Y here if you only have Tigon II based AceNICs and want to leave 2073 out support for the older Tigon I based cards which are no longer 2074 being sold (ie. the original Alteon AceNIC and 3Com 3C985 (non B 2075 version)). This will reduce the size of the driver object by 2076 app. 100KB. If you are not sure whether your card is a Tigon I or a 2077 Tigon II, say N here. 2078 2079 The safe and default value for this is N. 2080 2081config DL2K 2082 tristate "DL2000/TC902x-based Gigabit Ethernet support" 2083 depends on PCI 2084 select CRC32 2085 help 2086 This driver supports DL2000/TC902x-based Gigabit ethernet cards, 2087 which includes 2088 D-Link DGE-550T Gigabit Ethernet Adapter. 2089 D-Link DL2000-based Gigabit Ethernet Adapter. 2090 Sundance/Tamarack TC902x Gigabit Ethernet Adapter. 2091 2092 To compile this driver as a module, choose M here: the 2093 module will be called dl2k. 2094 2095config E1000 2096 tristate "Intel(R) PRO/1000 Gigabit Ethernet support" 2097 depends on PCI 2098 ---help--- 2099 This driver supports Intel(R) PRO/1000 gigabit ethernet family of 2100 adapters. For more information on how to identify your adapter, go 2101 to the Adapter & Driver ID Guide at: 2102 2103 <http://support.intel.com/support/network/adapter/pro100/21397.htm> 2104 2105 For general information and support, go to the Intel support 2106 website at: 2107 2108 <http://support.intel.com> 2109 2110 More specific information on configuring the driver is in 2111 <file:Documentation/networking/e1000.txt>. 2112 2113 To compile this driver as a module, choose M here. The module 2114 will be called e1000. 2115 2116config E1000E 2117 tristate "Intel(R) PRO/1000 PCI-Express Gigabit Ethernet support" 2118 select CRC32 2119 depends on PCI && (!SPARC32 || BROKEN) 2120 select CRC32 2121 ---help--- 2122 This driver supports the PCI-Express Intel(R) PRO/1000 gigabit 2123 ethernet family of adapters. For PCI or PCI-X e1000 adapters, 2124 use the regular e1000 driver For more information on how to 2125 identify your adapter, go to the Adapter & Driver ID Guide at: 2126 2127 <http://support.intel.com/support/network/adapter/pro100/21397.htm> 2128 2129 For general information and support, go to the Intel support 2130 website at: 2131 2132 <http://support.intel.com> 2133 2134 To compile this driver as a module, choose M here. The module 2135 will be called e1000e. 2136 2137config IP1000 2138 tristate "IP1000 Gigabit Ethernet support" 2139 depends on PCI && EXPERIMENTAL 2140 select MII 2141 ---help--- 2142 This driver supports IP1000 gigabit Ethernet cards. 2143 2144 To compile this driver as a module, choose M here: the module 2145 will be called ipg. This is recommended. 2146 2147config IGB 2148 tristate "Intel(R) 82575/82576 PCI-Express Gigabit Ethernet support" 2149 depends on PCI 2150 ---help--- 2151 This driver supports Intel(R) 82575/82576 gigabit ethernet family of 2152 adapters. For more information on how to identify your adapter, go 2153 to the Adapter & Driver ID Guide at: 2154 2155 <http://support.intel.com/support/network/adapter/pro100/21397.htm> 2156 2157 For general information and support, go to the Intel support 2158 website at: 2159 2160 <http://support.intel.com> 2161 2162 More specific information on configuring the driver is in 2163 <file:Documentation/networking/e1000.txt>. 2164 2165 To compile this driver as a module, choose M here. The module 2166 will be called igb. 2167 2168config IGB_DCA 2169 bool "Direct Cache Access (DCA) Support" 2170 default y 2171 depends on IGB && DCA && !(IGB=y && DCA=m) 2172 ---help--- 2173 Say Y here if you want to use Direct Cache Access (DCA) in the 2174 driver. DCA is a method for warming the CPU cache before data 2175 is used, with the intent of lessening the impact of cache misses. 2176 2177config IGBVF 2178 tristate "Intel(R) 82576 Virtual Function Ethernet support" 2179 depends on PCI 2180 ---help--- 2181 This driver supports Intel(R) 82576 virtual functions. For more 2182 information on how to identify your adapter, go to the Adapter & 2183 Driver ID Guide at: 2184 2185 <http://support.intel.com/support/network/adapter/pro100/21397.htm> 2186 2187 For general information and support, go to the Intel support 2188 website at: 2189 2190 <http://support.intel.com> 2191 2192 More specific information on configuring the driver is in 2193 <file:Documentation/networking/e1000.txt>. 2194 2195 To compile this driver as a module, choose M here. The module 2196 will be called igbvf. 2197 2198source "drivers/net/ixp2000/Kconfig" 2199 2200config MYRI_SBUS 2201 tristate "MyriCOM Gigabit Ethernet support" 2202 depends on SBUS 2203 help 2204 This driver supports MyriCOM Sbus gigabit Ethernet cards. 2205 2206 To compile this driver as a module, choose M here: the module 2207 will be called myri_sbus. This is recommended. 2208 2209config NS83820 2210 tristate "National Semiconductor DP83820 support" 2211 depends on PCI 2212 help 2213 This is a driver for the National Semiconductor DP83820 series 2214 of gigabit ethernet MACs. Cards using this chipset include 2215 the D-Link DGE-500T, PureData's PDP8023Z-TG, SMC's SMC9462TX, 2216 SOHO-GA2000T, SOHO-GA2500T. The driver supports the use of 2217 zero copy. 2218 2219config HAMACHI 2220 tristate "Packet Engines Hamachi GNIC-II support" 2221 depends on PCI 2222 select MII 2223 help 2224 If you have a Gigabit Ethernet card of this type, say Y and read 2225 the Ethernet-HOWTO, available from 2226 <http://www.tldp.org/docs.html#howto>. 2227 2228 To compile this driver as a module, choose M here. The module will be 2229 called hamachi. 2230 2231config YELLOWFIN 2232 tristate "Packet Engines Yellowfin Gigabit-NIC support (EXPERIMENTAL)" 2233 depends on PCI && EXPERIMENTAL 2234 select CRC32 2235 ---help--- 2236 Say Y here if you have a Packet Engines G-NIC PCI Gigabit Ethernet 2237 adapter or the SYM53C885 Ethernet controller. The Gigabit adapter is 2238 used by the Beowulf Linux cluster project. See 2239 <http://cesdis.gsfc.nasa.gov/linux/drivers/yellowfin.html> for more 2240 information about this driver in particular and Beowulf in general. 2241 2242 To compile this driver as a module, choose M here: the module 2243 will be called yellowfin. This is recommended. 2244 2245config R8169 2246 tristate "Realtek 8169 gigabit ethernet support" 2247 depends on PCI 2248 select FW_LOADER 2249 select CRC32 2250 select MII 2251 ---help--- 2252 Say Y here if you have a Realtek 8169 PCI Gigabit Ethernet adapter. 2253 2254 To compile this driver as a module, choose M here: the module 2255 will be called r8169. This is recommended. 2256 2257config SB1250_MAC 2258 tristate "SB1250 Gigabit Ethernet support" 2259 depends on SIBYTE_SB1xxx_SOC 2260 select PHYLIB 2261 ---help--- 2262 This driver supports Gigabit Ethernet interfaces based on the 2263 Broadcom SiByte family of System-On-a-Chip parts. They include 2264 the BCM1120, BCM1125, BCM1125H, BCM1250, BCM1255, BCM1280, BCM1455 2265 and BCM1480 chips. 2266 2267 To compile this driver as a module, choose M here: the module 2268 will be called sb1250-mac. 2269 2270config SIS190 2271 tristate "SiS190/SiS191 gigabit ethernet support" 2272 depends on PCI 2273 select CRC32 2274 select MII 2275 ---help--- 2276 Say Y here if you have a SiS 190 PCI Fast Ethernet adapter or 2277 a SiS 191 PCI Gigabit Ethernet adapter. Both are expected to 2278 appear in lan on motherboard designs which are based on SiS 965 2279 and SiS 966 south bridge. 2280 2281 To compile this driver as a module, choose M here: the module 2282 will be called sis190. This is recommended. 2283 2284config SKGE 2285 tristate "New SysKonnect GigaEthernet support" 2286 depends on PCI 2287 select CRC32 2288 ---help--- 2289 This driver support the Marvell Yukon or SysKonnect SK-98xx/SK-95xx 2290 and related Gigabit Ethernet adapters. It is a new smaller driver 2291 with better performance and more complete ethtool support. 2292 2293 It does not support the link failover and network management 2294 features that "portable" vendor supplied sk98lin driver does. 2295 2296 This driver supports adapters based on the original Yukon chipset: 2297 Marvell 88E8001, Belkin F5D5005, CNet GigaCard, DLink DGE-530T, 2298 Linksys EG1032/EG1064, 3Com 3C940/3C940B, SysKonnect SK-9871/9872. 2299 2300 It does not support the newer Yukon2 chipset: a separate driver, 2301 sky2, is provided for Yukon2-based adapters. 2302 2303 To compile this driver as a module, choose M here: the module 2304 will be called skge. This is recommended. 2305 2306config SKGE_DEBUG 2307 bool "Debugging interface" 2308 depends on SKGE && DEBUG_FS 2309 help 2310 This option adds the ability to dump driver state for debugging. 2311 The file /sys/kernel/debug/skge/ethX displays the state of the internal 2312 transmit and receive rings. 2313 2314 If unsure, say N. 2315 2316config SKY2 2317 tristate "SysKonnect Yukon2 support" 2318 depends on PCI 2319 select CRC32 2320 ---help--- 2321 This driver supports Gigabit Ethernet adapters based on the 2322 Marvell Yukon 2 chipset: 2323 Marvell 88E8021/88E8022/88E8035/88E8036/88E8038/88E8050/88E8052/ 2324 88E8053/88E8055/88E8061/88E8062, SysKonnect SK-9E21D/SK-9S21 2325 2326 There is companion driver for the older Marvell Yukon and 2327 Genesis based adapters: skge. 2328 2329 To compile this driver as a module, choose M here: the module 2330 will be called sky2. This is recommended. 2331 2332config SKY2_DEBUG 2333 bool "Debugging interface" 2334 depends on SKY2 && DEBUG_FS 2335 help 2336 This option adds the ability to dump driver state for debugging. 2337 The file /sys/kernel/debug/sky2/ethX displays the state of the internal 2338 transmit and receive rings. 2339 2340 If unsure, say N. 2341 2342config VIA_VELOCITY 2343 tristate "VIA Velocity support" 2344 depends on PCI 2345 select CRC32 2346 select CRC_CCITT 2347 select MII 2348 help 2349 If you have a VIA "Velocity" based network card say Y here. 2350 2351 To compile this driver as a module, choose M here. The module 2352 will be called via-velocity. 2353 2354config TIGON3 2355 tristate "Broadcom Tigon3 support" 2356 depends on PCI 2357 select PHYLIB 2358 help 2359 This driver supports Broadcom Tigon3 based gigabit Ethernet cards. 2360 2361 To compile this driver as a module, choose M here: the module 2362 will be called tg3. This is recommended. 2363 2364config BNX2 2365 tristate "Broadcom NetXtremeII support" 2366 depends on PCI 2367 select CRC32 2368 select FW_LOADER 2369 help 2370 This driver supports Broadcom NetXtremeII gigabit Ethernet cards. 2371 2372 To compile this driver as a module, choose M here: the module 2373 will be called bnx2. This is recommended. 2374 2375config CNIC 2376 tristate "Broadcom CNIC support" 2377 depends on PCI 2378 select BNX2 2379 select UIO 2380 help 2381 This driver supports offload features of Broadcom NetXtremeII 2382 gigabit Ethernet cards. 2383 2384 To compile this driver as a module, choose M here: the module 2385 will be called cnic. This is recommended. 2386 2387config SPIDER_NET 2388 tristate "Spider Gigabit Ethernet driver" 2389 depends on PCI && (PPC_IBM_CELL_BLADE || PPC_CELLEB) 2390 select FW_LOADER 2391 help 2392 This driver supports the Gigabit Ethernet chips present on the 2393 Cell Processor-Based Blades from IBM. 2394 2395config TSI108_ETH 2396 tristate "Tundra TSI108 gigabit Ethernet support" 2397 depends on TSI108_BRIDGE 2398 help 2399 This driver supports Tundra TSI108 gigabit Ethernet ports. 2400 To compile this driver as a module, choose M here: the module 2401 will be called tsi108_eth. 2402 2403config GELIC_NET 2404 tristate "PS3 Gigabit Ethernet driver" 2405 depends on PPC_PS3 2406 select PS3_SYS_MANAGER 2407 help 2408 This driver supports the network device on the PS3 game 2409 console. This driver has built-in support for Ethernet. 2410 2411 To compile this driver as a module, choose M here: the 2412 module will be called ps3_gelic. 2413 2414config GELIC_WIRELESS 2415 bool "PS3 Wireless support" 2416 depends on WLAN 2417 depends on GELIC_NET 2418 select WIRELESS_EXT 2419 help 2420 This option adds the support for the wireless feature of PS3. 2421 If you have the wireless-less model of PS3 or have no plan to 2422 use wireless feature, disabling this option saves memory. As 2423 the driver automatically distinguishes the models, you can 2424 safely enable this option even if you have a wireless-less model. 2425 2426config FSL_PQ_MDIO 2427 tristate "Freescale PQ MDIO" 2428 depends on FSL_SOC 2429 select PHYLIB 2430 help 2431 This driver supports the MDIO bus used by the gianfar and UCC drivers. 2432 2433config GIANFAR 2434 tristate "Gianfar Ethernet" 2435 depends on FSL_SOC 2436 select FSL_PQ_MDIO 2437 select PHYLIB 2438 select CRC32 2439 help 2440 This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx, 2441 and MPC86xx family of chips, and the FEC on the 8540. 2442 2443config UCC_GETH 2444 tristate "Freescale QE Gigabit Ethernet" 2445 depends on QUICC_ENGINE 2446 select FSL_PQ_MDIO 2447 select PHYLIB 2448 help 2449 This driver supports the Gigabit Ethernet mode of the QUICC Engine, 2450 which is available on some Freescale SOCs. 2451 2452config UGETH_TX_ON_DEMAND 2453 bool "Transmit on Demand support" 2454 depends on UCC_GETH 2455 2456config MV643XX_ETH 2457 tristate "Marvell Discovery (643XX) and Orion ethernet support" 2458 depends on (MV64X60 || PPC32 || PLAT_ORION) && INET 2459 select INET_LRO 2460 select PHYLIB 2461 help 2462 This driver supports the gigabit ethernet MACs in the 2463 Marvell Discovery PPC/MIPS chipset family (MV643XX) and 2464 in the Marvell Orion ARM SoC family. 2465 2466 Some boards that use the Discovery chipset are the Momenco 2467 Ocelot C and Jaguar ATX and Pegasos II. 2468 2469config XILINX_LL_TEMAC 2470 tristate "Xilinx LL TEMAC (LocalLink Tri-mode Ethernet MAC) driver" 2471 depends on PPC || MICROBLAZE 2472 select PHYLIB 2473 help 2474 This driver supports the Xilinx 10/100/1000 LocalLink TEMAC 2475 core used in Xilinx Spartan and Virtex FPGAs 2476 2477config QLA3XXX 2478 tristate "QLogic QLA3XXX Network Driver Support" 2479 depends on PCI 2480 help 2481 This driver supports QLogic ISP3XXX gigabit Ethernet cards. 2482 2483 To compile this driver as a module, choose M here: the module 2484 will be called qla3xxx. 2485 2486config ATL1 2487 tristate "Atheros/Attansic L1 Gigabit Ethernet support" 2488 depends on PCI 2489 select CRC32 2490 select MII 2491 help 2492 This driver supports the Atheros/Attansic L1 gigabit ethernet 2493 adapter. 2494 2495 To compile this driver as a module, choose M here. The module 2496 will be called atl1. 2497 2498config ATL1E 2499 tristate "Atheros L1E Gigabit Ethernet support (EXPERIMENTAL)" 2500 depends on PCI && EXPERIMENTAL 2501 select CRC32 2502 select MII 2503 help 2504 This driver supports the Atheros L1E gigabit ethernet adapter. 2505 2506 To compile this driver as a module, choose M here. The module 2507 will be called atl1e. 2508 2509config ATL1C 2510 tristate "Atheros L1C Gigabit Ethernet support (EXPERIMENTAL)" 2511 depends on PCI && EXPERIMENTAL 2512 select CRC32 2513 select MII 2514 help 2515 This driver supports the Atheros L1C gigabit ethernet adapter. 2516 2517 To compile this driver as a module, choose M here. The module 2518 will be called atl1c. 2519 2520config JME 2521 tristate "JMicron(R) PCI-Express Gigabit Ethernet support" 2522 depends on PCI 2523 select CRC32 2524 select MII 2525 ---help--- 2526 This driver supports the PCI-Express gigabit ethernet adapters 2527 based on JMicron JMC250 chipset. 2528 2529 To compile this driver as a module, choose M here. The module 2530 will be called jme. 2531 2532config S6GMAC 2533 tristate "S6105 GMAC ethernet support" 2534 depends on XTENSA_VARIANT_S6000 2535 select PHYLIB 2536 help 2537 This driver supports the on chip ethernet device on the 2538 S6105 xtensa processor. 2539 2540 To compile this driver as a module, choose M here. The module 2541 will be called s6gmac. 2542 2543source "drivers/net/stmmac/Kconfig" 2544 2545config PCH_GBE 2546 tristate "Intel EG20T PCH / OKI SEMICONDUCTOR ML7223 IOH GbE" 2547 depends on PCI 2548 select MII 2549 ---help--- 2550 This is a gigabit ethernet driver for EG20T PCH. 2551 EG20T PCH is the platform controller hub that is used in Intel's 2552 general embedded platform. 2553 EG20T PCH has Gigabit Ethernet interface. 2554 Using this interface, it is able to access system devices connected 2555 to Gigabit Ethernet. 2556 This driver enables Gigabit Ethernet function. 2557 2558 This driver also can be used for OKI SEMICONDUCTOR IOH(Input/ 2559 Output Hub), ML7223. 2560 ML7223 IOH is for MP(Media Phone) use. 2561 ML7223 is companion chip for Intel Atom E6xx series. 2562 ML7223 is completely compatible for Intel EG20T PCH. 2563 2564endif # NETDEV_1000 2565 2566# 2567# 10 Gigabit Ethernet 2568# 2569 2570menuconfig NETDEV_10000 2571 bool "Ethernet (10000 Mbit)" 2572 depends on !UML 2573 default y 2574 ---help--- 2575 Say Y here to get to see options for 10 Gigabit Ethernet drivers. 2576 This option alone does not add any kernel code. 2577 2578 If you say N, all options in this submenu will be skipped and disabled. 2579 2580if NETDEV_10000 2581 2582config MDIO 2583 tristate 2584 2585config CHELSIO_T1 2586 tristate "Chelsio 10Gb Ethernet support" 2587 depends on PCI 2588 select CRC32 2589 select MDIO 2590 help 2591 This driver supports Chelsio gigabit and 10-gigabit 2592 Ethernet cards. More information about adapter features and 2593 performance tuning is in <file:Documentation/networking/cxgb.txt>. 2594 2595 For general information about Chelsio and our products, visit 2596 our website at <http://www.chelsio.com>. 2597 2598 For customer support, please visit our customer support page at 2599 <http://www.chelsio.com/support.html>. 2600 2601 Please send feedback to <linux-bugs@chelsio.com>. 2602 2603 To compile this driver as a module, choose M here: the module 2604 will be called cxgb. 2605 2606config CHELSIO_T1_1G 2607 bool "Chelsio gigabit Ethernet support" 2608 depends on CHELSIO_T1 2609 help 2610 Enables support for Chelsio's gigabit Ethernet PCI cards. If you 2611 are using only 10G cards say 'N' here. 2612 2613config CHELSIO_T3 2614 tristate "Chelsio Communications T3 10Gb Ethernet support" 2615 depends on PCI && INET 2616 select FW_LOADER 2617 select MDIO 2618 help 2619 This driver supports Chelsio T3-based gigabit and 10Gb Ethernet 2620 adapters. 2621 2622 For general information about Chelsio and our products, visit 2623 our website at <http://www.chelsio.com>. 2624 2625 For customer support, please visit our customer support page at 2626 <http://www.chelsio.com/support.html>. 2627 2628 Please send feedback to <linux-bugs@chelsio.com>. 2629 2630 To compile this driver as a module, choose M here: the module 2631 will be called cxgb3. 2632 2633config CHELSIO_T4 2634 tristate "Chelsio Communications T4 Ethernet support" 2635 depends on PCI 2636 select FW_LOADER 2637 select MDIO 2638 help 2639 This driver supports Chelsio T4-based gigabit and 10Gb Ethernet 2640 adapters. 2641 2642 For general information about Chelsio and our products, visit 2643 our website at <http://www.chelsio.com>. 2644 2645 For customer support, please visit our customer support page at 2646 <http://www.chelsio.com/support.html>. 2647 2648 Please send feedback to <linux-bugs@chelsio.com>. 2649 2650 To compile this driver as a module choose M here; the module 2651 will be called cxgb4. 2652 2653config CHELSIO_T4VF 2654 tristate "Chelsio Communications T4 Virtual Function Ethernet support" 2655 depends on PCI 2656 help 2657 This driver supports Chelsio T4-based gigabit and 10Gb Ethernet 2658 adapters with PCI-E SR-IOV Virtual Functions. 2659 2660 For general information about Chelsio and our products, visit 2661 our website at <http://www.chelsio.com>. 2662 2663 For customer support, please visit our customer support page at 2664 <http://www.chelsio.com/support.html>. 2665 2666 Please send feedback to <linux-bugs@chelsio.com>. 2667 2668 To compile this driver as a module choose M here; the module 2669 will be called cxgb4vf. 2670 2671config EHEA 2672 tristate "eHEA Ethernet support" 2673 depends on IBMEBUS && INET && SPARSEMEM 2674 select INET_LRO 2675 ---help--- 2676 This driver supports the IBM pSeries eHEA ethernet adapter. 2677 2678 To compile the driver as a module, choose M here. The module 2679 will be called ehea. 2680 2681config ENIC 2682 tristate "Cisco VIC Ethernet NIC Support" 2683 depends on PCI && INET 2684 help 2685 This enables the support for the Cisco VIC Ethernet card. 2686 2687config IXGBE 2688 tristate "Intel(R) 10GbE PCI Express adapters support" 2689 depends on PCI && INET 2690 select MDIO 2691 ---help--- 2692 This driver supports Intel(R) 10GbE PCI Express family of 2693 adapters. For more information on how to identify your adapter, go 2694 to the Adapter & Driver ID Guide at: 2695 2696 <http://support.intel.com/support/network/adapter/pro100/21397.htm> 2697 2698 For general information and support, go to the Intel support 2699 website at: 2700 2701 <http://support.intel.com> 2702 2703 To compile this driver as a module, choose M here. The module 2704 will be called ixgbe. 2705 2706config IXGBE_DCA 2707 bool "Direct Cache Access (DCA) Support" 2708 default y 2709 depends on IXGBE && DCA && !(IXGBE=y && DCA=m) 2710 ---help--- 2711 Say Y here if you want to use Direct Cache Access (DCA) in the 2712 driver. DCA is a method for warming the CPU cache before data 2713 is used, with the intent of lessening the impact of cache misses. 2714 2715config IXGBE_DCB 2716 bool "Data Center Bridging (DCB) Support" 2717 default n 2718 depends on IXGBE && DCB 2719 ---help--- 2720 Say Y here if you want to use Data Center Bridging (DCB) in the 2721 driver. 2722 2723 If unsure, say N. 2724 2725config IXGBEVF 2726 tristate "Intel(R) 82599 Virtual Function Ethernet support" 2727 depends on PCI_MSI 2728 ---help--- 2729 This driver supports Intel(R) 82599 virtual functions. For more 2730 information on how to identify your adapter, go to the Adapter & 2731 Driver ID Guide at: 2732 2733 <http://support.intel.com/support/network/sb/CS-008441.htm> 2734 2735 For general information and support, go to the Intel support 2736 website at: 2737 2738 <http://support.intel.com> 2739 2740 More specific information on configuring the driver is in 2741 <file:Documentation/networking/ixgbevf.txt>. 2742 2743 To compile this driver as a module, choose M here. The module 2744 will be called ixgbevf. MSI-X interrupt support is required 2745 for this driver to work correctly. 2746 2747config IXGB 2748 tristate "Intel(R) PRO/10GbE support" 2749 depends on PCI 2750 ---help--- 2751 This driver supports Intel(R) PRO/10GbE family of adapters for 2752 PCI-X type cards. For PCI-E type cards, use the "ixgbe" driver 2753 instead. For more information on how to identify your adapter, go 2754 to the Adapter & Driver ID Guide at: 2755 2756 <http://support.intel.com/support/network/adapter/pro100/21397.htm> 2757 2758 For general information and support, go to the Intel support 2759 website at: 2760 2761 <http://support.intel.com> 2762 2763 More specific information on configuring the driver is in 2764 <file:Documentation/networking/ixgb.txt>. 2765 2766 To compile this driver as a module, choose M here. The module 2767 will be called ixgb. 2768 2769config S2IO 2770 tristate "Exar Xframe 10Gb Ethernet Adapter" 2771 depends on PCI 2772 ---help--- 2773 This driver supports Exar Corp's Xframe Series 10Gb Ethernet Adapters. 2774 2775 More specific information on configuring the driver is in 2776 <file:Documentation/networking/s2io.txt>. 2777 2778 To compile this driver as a module, choose M here. The module 2779 will be called s2io. 2780 2781config VXGE 2782 tristate "Exar X3100 Series 10GbE PCIe Server Adapter" 2783 depends on PCI && INET 2784 ---help--- 2785 This driver supports Exar Corp's X3100 Series 10 GbE PCIe 2786 I/O Virtualized Server Adapter. 2787 2788 More specific information on configuring the driver is in 2789 <file:Documentation/networking/vxge.txt>. 2790 2791 To compile this driver as a module, choose M here. The module 2792 will be called vxge. 2793 2794config VXGE_DEBUG_TRACE_ALL 2795 bool "Enabling All Debug trace statments in driver" 2796 default n 2797 depends on VXGE 2798 ---help--- 2799 Say Y here if you want to enabling all the debug trace statements in 2800 the vxge driver. By default only few debug trace statements are 2801 enabled. 2802 2803config MYRI10GE 2804 tristate "Myricom Myri-10G Ethernet support" 2805 depends on PCI && INET 2806 select FW_LOADER 2807 select CRC32 2808 select INET_LRO 2809 ---help--- 2810 This driver supports Myricom Myri-10G Dual Protocol interface in 2811 Ethernet mode. If the eeprom on your board is not recent enough, 2812 you will need a newer firmware image. 2813 You may get this image or more information, at: 2814 2815 <http://www.myri.com/scs/download-Myri10GE.html> 2816 2817 To compile this driver as a module, choose M here. The module 2818 will be called myri10ge. 2819 2820config MYRI10GE_DCA 2821 bool "Direct Cache Access (DCA) Support" 2822 default y 2823 depends on MYRI10GE && DCA && !(MYRI10GE=y && DCA=m) 2824 ---help--- 2825 Say Y here if you want to use Direct Cache Access (DCA) in the 2826 driver. DCA is a method for warming the CPU cache before data 2827 is used, with the intent of lessening the impact of cache misses. 2828 2829config NETXEN_NIC 2830 tristate "NetXen Multi port (1/10) Gigabit Ethernet NIC" 2831 depends on PCI 2832 select FW_LOADER 2833 help 2834 This enables the support for NetXen's Gigabit Ethernet card. 2835 2836config NIU 2837 tristate "Sun Neptune 10Gbit Ethernet support" 2838 depends on PCI 2839 select CRC32 2840 help 2841 This enables support for cards based upon Sun's 2842 Neptune chipset. 2843 2844config PASEMI_MAC 2845 tristate "PA Semi 1/10Gbit MAC" 2846 depends on PPC_PASEMI && PCI && INET 2847 select PHYLIB 2848 select INET_LRO 2849 help 2850 This driver supports the on-chip 1/10Gbit Ethernet controller on 2851 PA Semi's PWRficient line of chips. 2852 2853config MLX4_EN 2854 tristate "Mellanox Technologies 10Gbit Ethernet support" 2855 depends on PCI && INET 2856 select MLX4_CORE 2857 select INET_LRO 2858 help 2859 This driver supports Mellanox Technologies ConnectX Ethernet 2860 devices. 2861 2862config MLX4_CORE 2863 tristate 2864 depends on PCI 2865 default n 2866 2867config MLX4_DEBUG 2868 bool "Verbose debugging output" if (MLX4_CORE && EXPERT) 2869 depends on MLX4_CORE 2870 default y 2871 ---help--- 2872 This option causes debugging code to be compiled into the 2873 mlx4_core driver. The output can be turned on via the 2874 debug_level module parameter (which can also be set after 2875 the driver is loaded through sysfs). 2876 2877config TEHUTI 2878 tristate "Tehuti Networks 10G Ethernet" 2879 depends on PCI 2880 help 2881 Tehuti Networks 10G Ethernet NIC 2882 2883config BNX2X 2884 tristate "Broadcom NetXtremeII 10Gb support" 2885 depends on PCI 2886 select FW_LOADER 2887 select ZLIB_INFLATE 2888 select LIBCRC32C 2889 select MDIO 2890 help 2891 This driver supports Broadcom NetXtremeII 10 gigabit Ethernet cards. 2892 To compile this driver as a module, choose M here: the module 2893 will be called bnx2x. This is recommended. 2894 2895config QLCNIC 2896 tristate "QLOGIC QLCNIC 1/10Gb Converged Ethernet NIC Support" 2897 depends on PCI 2898 select FW_LOADER 2899 help 2900 This driver supports QLogic QLE8240 and QLE8242 Converged Ethernet 2901 devices. 2902 2903config QLGE 2904 tristate "QLogic QLGE 10Gb Ethernet Driver Support" 2905 depends on PCI 2906 help 2907 This driver supports QLogic ISP8XXX 10Gb Ethernet cards. 2908 2909 To compile this driver as a module, choose M here: the module 2910 will be called qlge. 2911 2912config BNA 2913 tristate "Brocade 1010/1020 10Gb Ethernet Driver support" 2914 depends on PCI 2915 ---help--- 2916 This driver supports Brocade 1010/1020 10Gb CEE capable Ethernet 2917 cards. 2918 To compile this driver as a module, choose M here: the module 2919 will be called bna. 2920 2921 For general information and support, go to the Brocade support 2922 website at: 2923 2924 <http://support.brocade.com> 2925 2926source "drivers/net/sfc/Kconfig" 2927 2928source "drivers/net/benet/Kconfig" 2929 2930endif # NETDEV_10000 2931 2932source "drivers/net/tokenring/Kconfig" 2933 2934source "drivers/net/wireless/Kconfig" 2935 2936source "drivers/net/wimax/Kconfig" 2937 2938source "drivers/net/usb/Kconfig" 2939 2940source "drivers/net/pcmcia/Kconfig" 2941 2942source "drivers/net/wan/Kconfig" 2943 2944source "drivers/atm/Kconfig" 2945 2946source "drivers/ieee802154/Kconfig" 2947 2948source "drivers/s390/net/Kconfig" 2949 2950source "drivers/net/caif/Kconfig" 2951 2952config TILE_NET 2953 tristate "Tilera GBE/XGBE network driver support" 2954 depends on TILE 2955 default y 2956 select CRC32 2957 help 2958 This is a standard Linux network device driver for the 2959 on-chip Tilera Gigabit Ethernet and XAUI interfaces. 2960 2961 To compile this driver as a module, choose M here: the module 2962 will be called tile_net. 2963 2964config XEN_NETDEV_FRONTEND 2965 tristate "Xen network device frontend driver" 2966 depends on XEN 2967 select XEN_XENBUS_FRONTEND 2968 default y 2969 help 2970 This driver provides support for Xen paravirtual network 2971 devices exported by a Xen network driver domain (often 2972 domain 0). 2973 2974 The corresponding Linux backend driver is enabled by the 2975 CONFIG_XEN_NETDEV_BACKEND option. 2976 2977 If you are compiling a kernel for use as Xen guest, you 2978 should say Y here. To compile this driver as a module, chose 2979 M here: the module will be called xen-netfront. 2980 2981config XEN_NETDEV_BACKEND 2982 tristate "Xen backend network device" 2983 depends on XEN_BACKEND 2984 help 2985 This driver allows the kernel to act as a Xen network driver 2986 domain which exports paravirtual network devices to other 2987 Xen domains. These devices can be accessed by any operating 2988 system that implements a compatible front end. 2989 2990 The corresponding Linux frontend driver is enabled by the 2991 CONFIG_XEN_NETDEV_FRONTEND configuration option. 2992 2993 The backend driver presents a standard network device 2994 endpoint for each paravirtual network device to the driver 2995 domain network stack. These can then be bridged or routed 2996 etc in order to provide full network connectivity. 2997 2998 If you are compiling a kernel to run in a Xen network driver 2999 domain (often this is domain 0) you should say Y here. To 3000 compile this driver as a module, chose M here: the module 3001 will be called xen-netback. 3002 3003config ISERIES_VETH 3004 tristate "iSeries Virtual Ethernet driver support" 3005 depends on PPC_ISERIES 3006 3007config RIONET 3008 tristate "RapidIO Ethernet over messaging driver support" 3009 depends on RAPIDIO 3010 3011config RIONET_TX_SIZE 3012 int "Number of outbound queue entries" 3013 depends on RIONET 3014 default "128" 3015 3016config RIONET_RX_SIZE 3017 int "Number of inbound queue entries" 3018 depends on RIONET 3019 default "128" 3020 3021config FDDI 3022 tristate "FDDI driver support" 3023 depends on (PCI || EISA || TC) 3024 help 3025 Fiber Distributed Data Interface is a high speed local area network 3026 design; essentially a replacement for high speed Ethernet. FDDI can 3027 run over copper or fiber. If you are connected to such a network and 3028 want a driver for the FDDI card in your computer, say Y here (and 3029 then also Y to the driver for your FDDI card, below). Most people 3030 will say N. 3031 3032config DEFXX 3033 tristate "Digital DEFTA/DEFEA/DEFPA adapter support" 3034 depends on FDDI && (PCI || EISA || TC) 3035 ---help--- 3036 This is support for the DIGITAL series of TURBOchannel (DEFTA), 3037 EISA (DEFEA) and PCI (DEFPA) controllers which can connect you 3038 to a local FDDI network. 3039 3040 To compile this driver as a module, choose M here: the module 3041 will be called defxx. If unsure, say N. 3042 3043config DEFXX_MMIO 3044 bool 3045 prompt "Use MMIO instead of PIO" if PCI || EISA 3046 depends on DEFXX 3047 default n if PCI || EISA 3048 default y 3049 ---help--- 3050 This instructs the driver to use EISA or PCI memory-mapped I/O 3051 (MMIO) as appropriate instead of programmed I/O ports (PIO). 3052 Enabling this gives an improvement in processing time in parts 3053 of the driver, but it may cause problems with EISA (DEFEA) 3054 adapters. TURBOchannel does not have the concept of I/O ports, 3055 so MMIO is always used for these (DEFTA) adapters. 3056 3057 If unsure, say N. 3058 3059config SKFP 3060 tristate "SysKonnect FDDI PCI support" 3061 depends on FDDI && PCI 3062 select BITREVERSE 3063 ---help--- 3064 Say Y here if you have a SysKonnect FDDI PCI adapter. 3065 The following adapters are supported by this driver: 3066 - SK-5521 (SK-NET FDDI-UP) 3067 - SK-5522 (SK-NET FDDI-UP DAS) 3068 - SK-5541 (SK-NET FDDI-FP) 3069 - SK-5543 (SK-NET FDDI-LP) 3070 - SK-5544 (SK-NET FDDI-LP DAS) 3071 - SK-5821 (SK-NET FDDI-UP64) 3072 - SK-5822 (SK-NET FDDI-UP64 DAS) 3073 - SK-5841 (SK-NET FDDI-FP64) 3074 - SK-5843 (SK-NET FDDI-LP64) 3075 - SK-5844 (SK-NET FDDI-LP64 DAS) 3076 - Netelligent 100 FDDI DAS Fibre SC 3077 - Netelligent 100 FDDI SAS Fibre SC 3078 - Netelligent 100 FDDI DAS UTP 3079 - Netelligent 100 FDDI SAS UTP 3080 - Netelligent 100 FDDI SAS Fibre MIC 3081 3082 Read <file:Documentation/networking/skfp.txt> for information about 3083 the driver. 3084 3085 Questions concerning this driver can be addressed to: 3086 <linux@syskonnect.de> 3087 3088 To compile this driver as a module, choose M here: the module 3089 will be called skfp. This is recommended. 3090 3091config HIPPI 3092 bool "HIPPI driver support (EXPERIMENTAL)" 3093 depends on EXPERIMENTAL && INET && PCI 3094 help 3095 HIgh Performance Parallel Interface (HIPPI) is a 800Mbit/sec and 3096 1600Mbit/sec dual-simplex switched or point-to-point network. HIPPI 3097 can run over copper (25m) or fiber (300m on multi-mode or 10km on 3098 single-mode). HIPPI networks are commonly used for clusters and to 3099 connect to super computers. If you are connected to a HIPPI network 3100 and have a HIPPI network card in your computer that you want to use 3101 under Linux, say Y here (you must also remember to enable the driver 3102 for your HIPPI card below). Most people will say N here. 3103 3104config ROADRUNNER 3105 tristate "Essential RoadRunner HIPPI PCI adapter support (EXPERIMENTAL)" 3106 depends on HIPPI && PCI 3107 help 3108 Say Y here if this is your PCI HIPPI network card. 3109 3110 To compile this driver as a module, choose M here: the module 3111 will be called rrunner. If unsure, say N. 3112 3113config ROADRUNNER_LARGE_RINGS 3114 bool "Use large TX/RX rings (EXPERIMENTAL)" 3115 depends on ROADRUNNER 3116 help 3117 If you say Y here, the RoadRunner driver will preallocate up to 2 MB 3118 of additional memory to allow for fastest operation, both for 3119 transmitting and receiving. This memory cannot be used by any other 3120 kernel code or by user space programs. Say Y here only if you have 3121 the memory. 3122 3123config PLIP 3124 tristate "PLIP (parallel port) support" 3125 depends on PARPORT 3126 ---help--- 3127 PLIP (Parallel Line Internet Protocol) is used to create a 3128 reasonably fast mini network consisting of two (or, rarely, more) 3129 local machines. A PLIP link from a Linux box is a popular means to 3130 install a Linux distribution on a machine which doesn't have a 3131 CD-ROM drive (a minimal system has to be transferred with floppies 3132 first). The kernels on both machines need to have this PLIP option 3133 enabled for this to work. 3134 3135 The PLIP driver has two modes, mode 0 and mode 1. The parallel 3136 ports (the connectors at the computers with 25 holes) are connected 3137 with "null printer" or "Turbo Laplink" cables which can transmit 4 3138 bits at a time (mode 0) or with special PLIP cables, to be used on 3139 bidirectional parallel ports only, which can transmit 8 bits at a 3140 time (mode 1); you can find the wiring of these cables in 3141 <file:Documentation/networking/PLIP.txt>. The cables can be up to 3142 15m long. Mode 0 works also if one of the machines runs DOS/Windows 3143 and has some PLIP software installed, e.g. the Crynwr PLIP packet 3144 driver (<http://oak.oakland.edu/simtel.net/msdos/pktdrvr-pre.html>) 3145 and winsock or NCSA's telnet. 3146 3147 If you want to use PLIP, say Y and read the PLIP mini-HOWTO as well 3148 as the NET-3-HOWTO, both available from 3149 <http://www.tldp.org/docs.html#howto>. Note that the PLIP 3150 protocol has been changed and this PLIP driver won't work together 3151 with the PLIP support in Linux versions 1.0.x. This option enlarges 3152 your kernel by about 8 KB. 3153 3154 To compile this driver as a module, choose M here. The module 3155 will be called plip. If unsure, say Y or M, in case you buy 3156 a laptop later. 3157 3158config PPP 3159 tristate "PPP (point-to-point protocol) support" 3160 select SLHC 3161 ---help--- 3162 PPP (Point to Point Protocol) is a newer and better SLIP. It serves 3163 the same purpose: sending Internet traffic over telephone (and other 3164 serial) lines. Ask your access provider if they support it, because 3165 otherwise you can't use it; most Internet access providers these 3166 days support PPP rather than SLIP. 3167 3168 To use PPP, you need an additional program called pppd as described 3169 in the PPP-HOWTO, available at 3170 <http://www.tldp.org/docs.html#howto>. Make sure that you have 3171 the version of pppd recommended in <file:Documentation/Changes>. 3172 The PPP option enlarges your kernel by about 16 KB. 3173 3174 There are actually two versions of PPP: the traditional PPP for 3175 asynchronous lines, such as regular analog phone lines, and 3176 synchronous PPP which can be used over digital ISDN lines for 3177 example. If you want to use PPP over phone lines or other 3178 asynchronous serial lines, you need to say Y (or M) here and also to 3179 the next option, "PPP support for async serial ports". For PPP over 3180 synchronous lines, you should say Y (or M) here and to "Support 3181 synchronous PPP", below. 3182 3183 If you said Y to "Version information on all symbols" above, then 3184 you cannot compile the PPP driver into the kernel; you can then only 3185 compile it as a module. To compile this driver as a module, choose M 3186 here. The module will be called ppp_generic. 3187 3188config PPP_MULTILINK 3189 bool "PPP multilink support (EXPERIMENTAL)" 3190 depends on PPP && EXPERIMENTAL 3191 help 3192 PPP multilink is a protocol (defined in RFC 1990) which allows you 3193 to combine several (logical or physical) lines into one logical PPP 3194 connection, so that you can utilize your full bandwidth. 3195 3196 This has to be supported at the other end as well and you need a 3197 version of the pppd daemon which understands the multilink protocol. 3198 3199 If unsure, say N. 3200 3201config PPP_FILTER 3202 bool "PPP filtering" 3203 depends on PPP 3204 help 3205 Say Y here if you want to be able to filter the packets passing over 3206 PPP interfaces. This allows you to control which packets count as 3207 activity (i.e. which packets will reset the idle timer or bring up 3208 a demand-dialed link) and which packets are to be dropped entirely. 3209 You need to say Y here if you wish to use the pass-filter and 3210 active-filter options to pppd. 3211 3212 If unsure, say N. 3213 3214config PPP_ASYNC 3215 tristate "PPP support for async serial ports" 3216 depends on PPP 3217 select CRC_CCITT 3218 ---help--- 3219 Say Y (or M) here if you want to be able to use PPP over standard 3220 asynchronous serial ports, such as COM1 or COM2 on a PC. If you use 3221 a modem (not a synchronous or ISDN modem) to contact your ISP, you 3222 need this option. 3223 3224 To compile this driver as a module, choose M here. 3225 3226 If unsure, say Y. 3227 3228config PPP_SYNC_TTY 3229 tristate "PPP support for sync tty ports" 3230 depends on PPP 3231 help 3232 Say Y (or M) here if you want to be able to use PPP over synchronous 3233 (HDLC) tty devices, such as the SyncLink adapter. These devices 3234 are often used for high-speed leased lines like T1/E1. 3235 3236 To compile this driver as a module, choose M here. 3237 3238config PPP_DEFLATE 3239 tristate "PPP Deflate compression" 3240 depends on PPP 3241 select ZLIB_INFLATE 3242 select ZLIB_DEFLATE 3243 ---help--- 3244 Support for the Deflate compression method for PPP, which uses the 3245 Deflate algorithm (the same algorithm that gzip uses) to compress 3246 each PPP packet before it is sent over the wire. The machine at the 3247 other end of the PPP link (usually your ISP) has to support the 3248 Deflate compression method as well for this to be useful. Even if 3249 they don't support it, it is safe to say Y here. 3250 3251 To compile this driver as a module, choose M here. 3252 3253config PPP_BSDCOMP 3254 tristate "PPP BSD-Compress compression" 3255 depends on PPP 3256 ---help--- 3257 Support for the BSD-Compress compression method for PPP, which uses 3258 the LZW compression method to compress each PPP packet before it is 3259 sent over the wire. The machine at the other end of the PPP link 3260 (usually your ISP) has to support the BSD-Compress compression 3261 method as well for this to be useful. Even if they don't support it, 3262 it is safe to say Y here. 3263 3264 The PPP Deflate compression method ("PPP Deflate compression", 3265 above) is preferable to BSD-Compress, because it compresses better 3266 and is patent-free. 3267 3268 Note that the BSD compression code will always be compiled as a 3269 module; it is called bsd_comp and will show up in the directory 3270 modules once you have said "make modules". If unsure, say N. 3271 3272config PPP_MPPE 3273 tristate "PPP MPPE compression (encryption) (EXPERIMENTAL)" 3274 depends on PPP && EXPERIMENTAL 3275 select CRYPTO 3276 select CRYPTO_SHA1 3277 select CRYPTO_ARC4 3278 select CRYPTO_ECB 3279 ---help--- 3280 Support for the MPPE Encryption protocol, as employed by the 3281 Microsoft Point-to-Point Tunneling Protocol. 3282 3283 See http://pptpclient.sourceforge.net/ for information on 3284 configuring PPTP clients and servers to utilize this method. 3285 3286config PPPOE 3287 tristate "PPP over Ethernet (EXPERIMENTAL)" 3288 depends on EXPERIMENTAL && PPP 3289 help 3290 Support for PPP over Ethernet. 3291 3292 This driver requires the latest version of pppd from the CVS 3293 repository at cvs.samba.org. Alternatively, see the 3294 RoaringPenguin package (<http://www.roaringpenguin.com/pppoe>) 3295 which contains instruction on how to use this driver (under 3296 the heading "Kernel mode PPPoE"). 3297 3298config PPTP 3299 tristate "PPP over IPv4 (PPTP) (EXPERIMENTAL)" 3300 depends on EXPERIMENTAL && PPP && NET_IPGRE_DEMUX 3301 help 3302 Support for PPP over IPv4.(Point-to-Point Tunneling Protocol) 3303 3304 This driver requires pppd plugin to work in client mode or 3305 modified pptpd (poptop) to work in server mode. 3306 See http://accel-pptp.sourceforge.net/ for information how to 3307 utilize this module. 3308 3309config PPPOATM 3310 tristate "PPP over ATM" 3311 depends on ATM && PPP 3312 help 3313 Support PPP (Point to Point Protocol) encapsulated in ATM frames. 3314 This implementation does not yet comply with section 8 of RFC2364, 3315 which can lead to bad results if the ATM peer loses state and 3316 changes its encapsulation unilaterally. 3317 3318config PPPOL2TP 3319 tristate "PPP over L2TP (EXPERIMENTAL)" 3320 depends on EXPERIMENTAL && L2TP && PPP 3321 help 3322 Support for PPP-over-L2TP socket family. L2TP is a protocol 3323 used by ISPs and enterprises to tunnel PPP traffic over UDP 3324 tunnels. L2TP is replacing PPTP for VPN uses. 3325 3326config SLIP 3327 tristate "SLIP (serial line) support" 3328 ---help--- 3329 Say Y if you intend to use SLIP or CSLIP (compressed SLIP) to 3330 connect to your Internet service provider or to connect to some 3331 other local Unix box or if you want to configure your Linux box as a 3332 Slip/CSlip server for other people to dial in. SLIP (Serial Line 3333 Internet Protocol) is a protocol used to send Internet traffic over 3334 serial connections such as telephone lines or null modem cables; 3335 nowadays, the protocol PPP is more commonly used for this same 3336 purpose. 3337 3338 Normally, your access provider has to support SLIP in order for you 3339 to be able to use it, but there is now a SLIP emulator called SLiRP 3340 around (available from 3341 <ftp://ibiblio.org/pub/Linux/system/network/serial/>) which 3342 allows you to use SLIP over a regular dial up shell connection. If 3343 you plan to use SLiRP, make sure to say Y to CSLIP, below. The 3344 NET-3-HOWTO, available from 3345 <http://www.tldp.org/docs.html#howto>, explains how to 3346 configure SLIP. Note that you don't need this option if you just 3347 want to run term (term is a program which gives you almost full 3348 Internet connectivity if you have a regular dial up shell account on 3349 some Internet connected Unix computer. Read 3350 <http://www.bart.nl/~patrickr/term-howto/Term-HOWTO.html>). SLIP 3351 support will enlarge your kernel by about 4 KB. If unsure, say N. 3352 3353 To compile this driver as a module, choose M here. The module 3354 will be called slip. 3355 3356config SLIP_COMPRESSED 3357 bool "CSLIP compressed headers" 3358 depends on SLIP 3359 select SLHC 3360 ---help--- 3361 This protocol is faster than SLIP because it uses compression on the 3362 TCP/IP headers (not on the data itself), but it has to be supported 3363 on both ends. Ask your access provider if you are not sure and 3364 answer Y, just in case. You will still be able to use plain SLIP. If 3365 you plan to use SLiRP, the SLIP emulator (available from 3366 <ftp://ibiblio.org/pub/Linux/system/network/serial/>) which 3367 allows you to use SLIP over a regular dial up shell connection, you 3368 definitely want to say Y here. The NET-3-HOWTO, available from 3369 <http://www.tldp.org/docs.html#howto>, explains how to configure 3370 CSLIP. This won't enlarge your kernel. 3371 3372config SLHC 3373 tristate 3374 help 3375 This option enables Van Jacobsen serial line header compression 3376 routines. 3377 3378config SLIP_SMART 3379 bool "Keepalive and linefill" 3380 depends on SLIP 3381 help 3382 Adds additional capabilities to the SLIP driver to support the 3383 RELCOM line fill and keepalive monitoring. Ideal on poor quality 3384 analogue lines. 3385 3386config SLIP_MODE_SLIP6 3387 bool "Six bit SLIP encapsulation" 3388 depends on SLIP 3389 help 3390 Just occasionally you may need to run IP over hostile serial 3391 networks that don't pass all control characters or are only seven 3392 bit. Saying Y here adds an extra mode you can use with SLIP: 3393 "slip6". In this mode, SLIP will only send normal ASCII symbols over 3394 the serial device. Naturally, this has to be supported at the other 3395 end of the link as well. It's good enough, for example, to run IP 3396 over the async ports of a Camtec JNT Pad. If unsure, say N. 3397 3398config NET_FC 3399 bool "Fibre Channel driver support" 3400 depends on SCSI && PCI 3401 help 3402 Fibre Channel is a high speed serial protocol mainly used to connect 3403 large storage devices to the computer; it is compatible with and 3404 intended to replace SCSI. 3405 3406 If you intend to use Fibre Channel, you need to have a Fibre channel 3407 adaptor card in your computer; say Y here and to the driver for your 3408 adaptor below. You also should have said Y to "SCSI support" and 3409 "SCSI generic support". 3410 3411config NETCONSOLE 3412 tristate "Network console logging support" 3413 ---help--- 3414 If you want to log kernel messages over the network, enable this. 3415 See <file:Documentation/networking/netconsole.txt> for details. 3416 3417config NETCONSOLE_DYNAMIC 3418 bool "Dynamic reconfiguration of logging targets" 3419 depends on NETCONSOLE && SYSFS && CONFIGFS_FS 3420 help 3421 This option enables the ability to dynamically reconfigure target 3422 parameters (interface, IP addresses, port numbers, MAC addresses) 3423 at runtime through a userspace interface exported using configfs. 3424 See <file:Documentation/networking/netconsole.txt> for details. 3425 3426config NETPOLL 3427 def_bool NETCONSOLE 3428 3429config NETPOLL_TRAP 3430 bool "Netpoll traffic trapping" 3431 default n 3432 depends on NETPOLL 3433 3434config NET_POLL_CONTROLLER 3435 def_bool NETPOLL 3436 3437config VIRTIO_NET 3438 tristate "Virtio network driver (EXPERIMENTAL)" 3439 depends on EXPERIMENTAL && VIRTIO 3440 ---help--- 3441 This is the virtual network driver for virtio. It can be used with 3442 lguest or QEMU based VMMs (like KVM or Xen). Say Y or M. 3443 3444config VMXNET3 3445 tristate "VMware VMXNET3 ethernet driver" 3446 depends on PCI && INET 3447 help 3448 This driver supports VMware's vmxnet3 virtual ethernet NIC. 3449 To compile this driver as a module, choose M here: the 3450 module will be called vmxnet3. 3451 3452endif # NETDEVICES 3453