1# 2# Network device configuration 3# 4 5menuconfig NETDEVICES 6 default y if UML 7 depends on NET 8 bool "Network device support" 9 ---help--- 10 You can say N here if you don't intend to connect your Linux box to 11 any other computer at all. 12 13 You'll have to say Y if your computer contains a network card that 14 you want to use under Linux. If you are going to run SLIP or PPP over 15 telephone line or null modem cable you need say Y here. Connecting 16 two machines with parallel ports using PLIP needs this, as well as 17 AX.25/KISS for sending Internet traffic over amateur radio links. 18 19 See also "The Linux Network Administrator's Guide" by Olaf Kirch and 20 Terry Dawson. Available at <http://www.tldp.org/guides.html>. 21 22 If unsure, say Y. 23 24# All the following symbols are dependent on NETDEVICES - do not repeat 25# that for each of the symbols. 26if NETDEVICES 27 28config MII 29 tristate 30 31config NET_CORE 32 default y 33 bool "Network core driver support" 34 ---help--- 35 You can say N here if you do not intend to use any of the 36 networking core drivers (i.e. VLAN, bridging, bonding, etc.) 37 38if NET_CORE 39 40config BONDING 41 tristate "Bonding driver support" 42 depends on INET 43 depends on IPV6 || IPV6=n 44 ---help--- 45 Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet 46 Channels together. This is called 'Etherchannel' by Cisco, 47 'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux. 48 49 The driver supports multiple bonding modes to allow for both high 50 performance and high availability operation. 51 52 Refer to <file:Documentation/networking/bonding.txt> for more 53 information. 54 55 To compile this driver as a module, choose M here: the module 56 will be called bonding. 57 58config DUMMY 59 tristate "Dummy net driver support" 60 ---help--- 61 This is essentially a bit-bucket device (i.e. traffic you send to 62 this device is consigned into oblivion) with a configurable IP 63 address. It is most commonly used in order to make your currently 64 inactive SLIP address seem like a real address for local programs. 65 If you use SLIP or PPP, you might want to say Y here. Since this 66 thing often comes in handy, the default is Y. It won't enlarge your 67 kernel either. What a deal. Read about it in the Network 68 Administrator's Guide, available from 69 <http://www.tldp.org/docs.html#guide>. 70 71 To compile this driver as a module, choose M here: the module 72 will be called dummy. 73 74config EQUALIZER 75 tristate "EQL (serial line load balancing) support" 76 ---help--- 77 If you have two serial connections to some other computer (this 78 usually requires two modems and two telephone lines) and you use 79 SLIP (the protocol for sending Internet traffic over telephone 80 lines) or PPP (a better SLIP) on them, you can make them behave like 81 one double speed connection using this driver. Naturally, this has 82 to be supported at the other end as well, either with a similar EQL 83 Linux driver or with a Livingston Portmaster 2e. 84 85 Say Y if you want this and read 86 <file:Documentation/networking/eql.txt>. You may also want to read 87 section 6.2 of the NET-3-HOWTO, available from 88 <http://www.tldp.org/docs.html#howto>. 89 90 To compile this driver as a module, choose M here: the module 91 will be called eql. If unsure, say N. 92 93config NET_FC 94 bool "Fibre Channel driver support" 95 depends on SCSI && PCI 96 help 97 Fibre Channel is a high speed serial protocol mainly used to connect 98 large storage devices to the computer; it is compatible with and 99 intended to replace SCSI. 100 101 If you intend to use Fibre Channel, you need to have a Fibre channel 102 adaptor card in your computer; say Y here and to the driver for your 103 adaptor below. You also should have said Y to "SCSI support" and 104 "SCSI generic support". 105 106config IFB 107 tristate "Intermediate Functional Block support" 108 depends on NET_CLS_ACT 109 ---help--- 110 This is an intermediate driver that allows sharing of 111 resources. 112 To compile this driver as a module, choose M here: the module 113 will be called ifb. If you want to use more than one ifb 114 device at a time, you need to compile this driver as a module. 115 Instead of 'ifb', the devices will then be called 'ifb0', 116 'ifb1' etc. 117 Look at the iproute2 documentation directory for usage etc 118 119source "drivers/net/team/Kconfig" 120 121config MACVLAN 122 tristate "MAC-VLAN support" 123 ---help--- 124 This allows one to create virtual interfaces that map packets to 125 or from specific MAC addresses to a particular interface. 126 127 Macvlan devices can be added using the "ip" command from the 128 iproute2 package starting with the iproute2-2.6.23 release: 129 130 "ip link add link <real dev> [ address MAC ] [ NAME ] type macvlan" 131 132 To compile this driver as a module, choose M here: the module 133 will be called macvlan. 134 135config MACVTAP 136 tristate "MAC-VLAN based tap driver" 137 depends on MACVLAN 138 help 139 This adds a specialized tap character device driver that is based 140 on the MAC-VLAN network interface, called macvtap. A macvtap device 141 can be added in the same way as a macvlan device, using 'type 142 macvtap', and then be accessed through the tap user space interface. 143 144 To compile this driver as a module, choose M here: the module 145 will be called macvtap. 146 147config VXLAN 148 tristate "Virtual eXtensible Local Area Network (VXLAN)" 149 depends on INET 150 select NET_UDP_TUNNEL 151 ---help--- 152 This allows one to create vxlan virtual interfaces that provide 153 Layer 2 Networks over Layer 3 Networks. VXLAN is often used 154 to tunnel virtual network infrastructure in virtualized environments. 155 For more information see: 156 http://tools.ietf.org/html/draft-mahalingam-dutt-dcops-vxlan-02 157 158 To compile this driver as a module, choose M here: the module 159 will be called vxlan. 160 161config NETCONSOLE 162 tristate "Network console logging support" 163 ---help--- 164 If you want to log kernel messages over the network, enable this. 165 See <file:Documentation/networking/netconsole.txt> for details. 166 167config NETCONSOLE_DYNAMIC 168 bool "Dynamic reconfiguration of logging targets" 169 depends on NETCONSOLE && SYSFS && CONFIGFS_FS && \ 170 !(NETCONSOLE=y && CONFIGFS_FS=m) 171 help 172 This option enables the ability to dynamically reconfigure target 173 parameters (interface, IP addresses, port numbers, MAC addresses) 174 at runtime through a userspace interface exported using configfs. 175 See <file:Documentation/networking/netconsole.txt> for details. 176 177config NETPOLL 178 def_bool NETCONSOLE 179 180config NET_POLL_CONTROLLER 181 def_bool NETPOLL 182 183config NTB_NETDEV 184 tristate "Virtual Ethernet over NTB" 185 depends on NTB 186 187config RIONET 188 tristate "RapidIO Ethernet over messaging driver support" 189 depends on RAPIDIO 190 191config RIONET_TX_SIZE 192 int "Number of outbound queue entries" 193 depends on RIONET 194 default "128" 195 196config RIONET_RX_SIZE 197 int "Number of inbound queue entries" 198 depends on RIONET 199 default "128" 200 201config TUN 202 tristate "Universal TUN/TAP device driver support" 203 select CRC32 204 ---help--- 205 TUN/TAP provides packet reception and transmission for user space 206 programs. It can be viewed as a simple Point-to-Point or Ethernet 207 device, which instead of receiving packets from a physical media, 208 receives them from user space program and instead of sending packets 209 via physical media writes them to the user space program. 210 211 When a program opens /dev/net/tun, driver creates and registers 212 corresponding net device tunX or tapX. After a program closed above 213 devices, driver will automatically delete tunXX or tapXX device and 214 all routes corresponding to it. 215 216 Please read <file:Documentation/networking/tuntap.txt> for more 217 information. 218 219 To compile this driver as a module, choose M here: the module 220 will be called tun. 221 222 If you don't know what to use this for, you don't need it. 223 224config VETH 225 tristate "Virtual ethernet pair device" 226 ---help--- 227 This device is a local ethernet tunnel. Devices are created in pairs. 228 When one end receives the packet it appears on its pair and vice 229 versa. 230 231config VIRTIO_NET 232 tristate "Virtio network driver" 233 depends on VIRTIO 234 select AVERAGE 235 ---help--- 236 This is the virtual network driver for virtio. It can be used with 237 lguest or QEMU based VMMs (like KVM or Xen). Say Y or M. 238 239config NLMON 240 tristate "Virtual netlink monitoring device" 241 ---help--- 242 This option enables a monitoring net device for netlink skbs. The 243 purpose of this is to analyze netlink messages with packet sockets. 244 Thus applications like tcpdump will be able to see local netlink 245 messages if they tap into the netlink device, record pcaps for further 246 diagnostics, etc. This is mostly intended for developers or support 247 to debug netlink issues. If unsure, say N. 248 249endif # NET_CORE 250 251config SUNGEM_PHY 252 tristate 253 254source "drivers/net/arcnet/Kconfig" 255 256source "drivers/atm/Kconfig" 257 258source "drivers/net/caif/Kconfig" 259 260source "drivers/net/dsa/Kconfig" 261 262source "drivers/net/ethernet/Kconfig" 263 264source "drivers/net/fddi/Kconfig" 265 266source "drivers/net/hippi/Kconfig" 267 268config NET_SB1000 269 tristate "General Instruments Surfboard 1000" 270 depends on PNP 271 ---help--- 272 This is a driver for the General Instrument (also known as 273 NextLevel) SURFboard 1000 internal 274 cable modem. This is an ISA card which is used by a number of cable 275 TV companies to provide cable modem access. It's a one-way 276 downstream-only cable modem, meaning that your upstream net link is 277 provided by your regular phone modem. 278 279 At present this driver only compiles as a module, so say M here if 280 you have this card. The module will be called sb1000. Then read 281 <file:Documentation/networking/README.sb1000> for information on how 282 to use this module, as it needs special ppp scripts for establishing 283 a connection. Further documentation and the necessary scripts can be 284 found at: 285 286 <http://www.jacksonville.net/~fventuri/> 287 <http://home.adelphia.net/~siglercm/sb1000.html> 288 <http://linuxpower.cx/~cable/> 289 290 If you don't have this card, of course say N. 291 292source "drivers/net/phy/Kconfig" 293 294source "drivers/net/plip/Kconfig" 295 296source "drivers/net/ppp/Kconfig" 297 298source "drivers/net/slip/Kconfig" 299 300source "drivers/s390/net/Kconfig" 301 302source "drivers/net/usb/Kconfig" 303 304source "drivers/net/wireless/Kconfig" 305 306source "drivers/net/wimax/Kconfig" 307 308source "drivers/net/wan/Kconfig" 309 310source "drivers/net/ieee802154/Kconfig" 311 312config XEN_NETDEV_FRONTEND 313 tristate "Xen network device frontend driver" 314 depends on XEN 315 select XEN_XENBUS_FRONTEND 316 default y 317 help 318 This driver provides support for Xen paravirtual network 319 devices exported by a Xen network driver domain (often 320 domain 0). 321 322 The corresponding Linux backend driver is enabled by the 323 CONFIG_XEN_NETDEV_BACKEND option. 324 325 If you are compiling a kernel for use as Xen guest, you 326 should say Y here. To compile this driver as a module, chose 327 M here: the module will be called xen-netfront. 328 329config XEN_NETDEV_BACKEND 330 tristate "Xen backend network device" 331 depends on XEN_BACKEND 332 help 333 This driver allows the kernel to act as a Xen network driver 334 domain which exports paravirtual network devices to other 335 Xen domains. These devices can be accessed by any operating 336 system that implements a compatible front end. 337 338 The corresponding Linux frontend driver is enabled by the 339 CONFIG_XEN_NETDEV_FRONTEND configuration option. 340 341 The backend driver presents a standard network device 342 endpoint for each paravirtual network device to the driver 343 domain network stack. These can then be bridged or routed 344 etc in order to provide full network connectivity. 345 346 If you are compiling a kernel to run in a Xen network driver 347 domain (often this is domain 0) you should say Y here. To 348 compile this driver as a module, chose M here: the module 349 will be called xen-netback. 350 351config VMXNET3 352 tristate "VMware VMXNET3 ethernet driver" 353 depends on PCI && INET 354 help 355 This driver supports VMware's vmxnet3 virtual ethernet NIC. 356 To compile this driver as a module, choose M here: the 357 module will be called vmxnet3. 358 359source "drivers/net/hyperv/Kconfig" 360 361endif # NETDEVICES 362