1config MTD_NAND_ECC 2 tristate 3 4config MTD_NAND_ECC_SMC 5 bool "NAND ECC Smart Media byte order" 6 depends on MTD_NAND_ECC 7 default n 8 help 9 Software ECC according to the Smart Media Specification. 10 The original Linux implementation had byte 0 and 1 swapped. 11 12 13menuconfig MTD_NAND 14 tristate "NAND Device Support" 15 depends on MTD 16 select MTD_NAND_IDS 17 select MTD_NAND_ECC 18 help 19 This enables support for accessing all type of NAND flash 20 devices. For further information see 21 <http://www.linux-mtd.infradead.org/doc/nand.html>. 22 23if MTD_NAND 24 25config MTD_NAND_VERIFY_WRITE 26 bool "Verify NAND page writes" 27 help 28 This adds an extra check when data is written to the flash. The 29 NAND flash device internally checks only bits transitioning 30 from 1 to 0. There is a rare possibility that even though the 31 device thinks the write was successful, a bit could have been 32 flipped accidentally due to device wear or something else. 33 34config MTD_SM_COMMON 35 tristate 36 default n 37 38config MTD_NAND_MUSEUM_IDS 39 bool "Enable chip ids for obsolete ancient NAND devices" 40 depends on MTD_NAND 41 default n 42 help 43 Enable this option only when your board has first generation 44 NAND chips (page size 256 byte, erase size 4-8KiB). The IDs 45 of these chips were reused by later, larger chips. 46 47config MTD_NAND_AUTCPU12 48 tristate "SmartMediaCard on autronix autcpu12 board" 49 depends on ARCH_AUTCPU12 50 help 51 This enables the driver for the autronix autcpu12 board to 52 access the SmartMediaCard. 53 54config MTD_NAND_DENALI 55 depends on PCI 56 tristate "Support Denali NAND controller on Intel Moorestown" 57 help 58 Enable the driver for NAND flash on Intel Moorestown, using the 59 Denali NAND controller core. 60 61config MTD_NAND_DENALI_SCRATCH_REG_ADDR 62 hex "Denali NAND size scratch register address" 63 default "0xFF108018" 64 help 65 Some platforms place the NAND chip size in a scratch register 66 because (some versions of) the driver aren't able to automatically 67 determine the size of certain chips. Set the address of the 68 scratch register here to enable this feature. On Intel Moorestown 69 boards, the scratch register is at 0xFF108018. 70 71config MTD_NAND_EDB7312 72 tristate "Support for Cirrus Logic EBD7312 evaluation board" 73 depends on ARCH_EDB7312 74 help 75 This enables the driver for the Cirrus Logic EBD7312 evaluation 76 board to access the onboard NAND Flash. 77 78config MTD_NAND_H1900 79 tristate "iPAQ H1900 flash" 80 depends on ARCH_PXA && MTD_PARTITIONS 81 help 82 This enables the driver for the iPAQ h1900 flash. 83 84config MTD_NAND_GPIO 85 tristate "GPIO NAND Flash driver" 86 depends on GENERIC_GPIO && ARM 87 help 88 This enables a GPIO based NAND flash driver. 89 90config MTD_NAND_SPIA 91 tristate "NAND Flash device on SPIA board" 92 depends on ARCH_P720T 93 help 94 If you had to ask, you don't have one. Say 'N'. 95 96config MTD_NAND_AMS_DELTA 97 tristate "NAND Flash device on Amstrad E3" 98 depends on MACH_AMS_DELTA 99 help 100 Support for NAND flash on Amstrad E3 (Delta). 101 102config MTD_NAND_OMAP2 103 tristate "NAND Flash device on OMAP2 and OMAP3" 104 depends on ARM && MTD_NAND && (ARCH_OMAP2 || ARCH_OMAP3) 105 help 106 Support for NAND flash on Texas Instruments OMAP2 and OMAP3 platforms. 107 108config MTD_NAND_OMAP_PREFETCH 109 bool "GPMC prefetch support for NAND Flash device" 110 depends on MTD_NAND && MTD_NAND_OMAP2 111 default y 112 help 113 The NAND device can be accessed for Read/Write using GPMC PREFETCH engine 114 to improve the performance. 115 116config MTD_NAND_OMAP_PREFETCH_DMA 117 depends on MTD_NAND_OMAP_PREFETCH 118 bool "DMA mode" 119 default n 120 help 121 The GPMC PREFETCH engine can be configured eigther in MPU interrupt mode 122 or in DMA interrupt mode. 123 Say y for DMA mode or MPU mode will be used 124 125config MTD_NAND_IDS 126 tristate 127 128config MTD_NAND_RICOH 129 tristate "Ricoh xD card reader" 130 default n 131 depends on PCI 132 select MTD_SM_COMMON 133 help 134 Enable support for Ricoh R5C852 xD card reader 135 You also need to enable ether 136 NAND SSFDC (SmartMedia) read only translation layer' or new 137 expermental, readwrite 138 'SmartMedia/xD new translation layer' 139 140config MTD_NAND_AU1550 141 tristate "Au1550/1200 NAND support" 142 depends on SOC_AU1200 || SOC_AU1550 143 help 144 This enables the driver for the NAND flash controller on the 145 AMD/Alchemy 1550 SOC. 146 147config MTD_NAND_BF5XX 148 tristate "Blackfin on-chip NAND Flash Controller driver" 149 depends on (BF54x || BF52x) && MTD_NAND 150 help 151 This enables the Blackfin on-chip NAND flash controller 152 153 No board specific support is done by this driver, each board 154 must advertise a platform_device for the driver to attach. 155 156 This driver can also be built as a module. If so, the module 157 will be called bf5xx-nand. 158 159config MTD_NAND_BF5XX_HWECC 160 bool "BF5XX NAND Hardware ECC" 161 default y 162 depends on MTD_NAND_BF5XX 163 help 164 Enable the use of the BF5XX's internal ECC generator when 165 using NAND. 166 167config MTD_NAND_BF5XX_BOOTROM_ECC 168 bool "Use Blackfin BootROM ECC Layout" 169 default n 170 depends on MTD_NAND_BF5XX_HWECC 171 help 172 If you wish to modify NAND pages and allow the Blackfin on-chip 173 BootROM to boot from them, say Y here. This is only necessary 174 if you are booting U-Boot out of NAND and you wish to update 175 U-Boot from Linux' userspace. Otherwise, you should say N here. 176 177 If unsure, say N. 178 179config MTD_NAND_RTC_FROM4 180 tristate "Renesas Flash ROM 4-slot interface board (FROM_BOARD4)" 181 depends on SH_SOLUTION_ENGINE 182 select REED_SOLOMON 183 select REED_SOLOMON_DEC8 184 select BITREVERSE 185 help 186 This enables the driver for the Renesas Technology AG-AND 187 flash interface board (FROM_BOARD4) 188 189config MTD_NAND_PPCHAMELEONEVB 190 tristate "NAND Flash device on PPChameleonEVB board" 191 depends on PPCHAMELEONEVB && BROKEN 192 help 193 This enables the NAND flash driver on the PPChameleon EVB Board. 194 195config MTD_NAND_S3C2410 196 tristate "NAND Flash support for Samsung S3C SoCs" 197 depends on ARCH_S3C2410 || ARCH_S3C64XX 198 help 199 This enables the NAND flash controller on the S3C24xx and S3C64xx 200 SoCs 201 202 No board specific support is done by this driver, each board 203 must advertise a platform_device for the driver to attach. 204 205config MTD_NAND_S3C2410_DEBUG 206 bool "Samsung S3C NAND driver debug" 207 depends on MTD_NAND_S3C2410 208 help 209 Enable debugging of the S3C NAND driver 210 211config MTD_NAND_S3C2410_HWECC 212 bool "Samsung S3C NAND Hardware ECC" 213 depends on MTD_NAND_S3C2410 214 help 215 Enable the use of the controller's internal ECC generator when 216 using NAND. Early versions of the chips have had problems with 217 incorrect ECC generation, and if using these, the default of 218 software ECC is preferable. 219 220config MTD_NAND_NDFC 221 tristate "NDFC NanD Flash Controller" 222 depends on 4xx 223 select MTD_NAND_ECC_SMC 224 help 225 NDFC Nand Flash Controllers are integrated in IBM/AMCC's 4xx SoCs 226 227config MTD_NAND_S3C2410_CLKSTOP 228 bool "Samsung S3C NAND IDLE clock stop" 229 depends on MTD_NAND_S3C2410 230 default n 231 help 232 Stop the clock to the NAND controller when there is no chip 233 selected to save power. This will mean there is a small delay 234 when the is NAND chip selected or released, but will save 235 approximately 5mA of power when there is nothing happening. 236 237config MTD_NAND_BCM_UMI 238 tristate "NAND Flash support for BCM Reference Boards" 239 depends on ARCH_BCMRING && MTD_NAND 240 help 241 This enables the NAND flash controller on the BCM UMI block. 242 243 No board specfic support is done by this driver, each board 244 must advertise a platform_device for the driver to attach. 245 246config MTD_NAND_BCM_UMI_HWCS 247 bool "BCM UMI NAND Hardware CS" 248 depends on MTD_NAND_BCM_UMI 249 help 250 Enable the use of the BCM UMI block's internal CS using NAND. 251 This should only be used if you know the external NAND CS can toggle. 252 253config MTD_NAND_DISKONCHIP 254 tristate "DiskOnChip 2000, Millennium and Millennium Plus (NAND reimplementation) (EXPERIMENTAL)" 255 depends on EXPERIMENTAL 256 select REED_SOLOMON 257 select REED_SOLOMON_DEC16 258 help 259 This is a reimplementation of M-Systems DiskOnChip 2000, 260 Millennium and Millennium Plus as a standard NAND device driver, 261 as opposed to the earlier self-contained MTD device drivers. 262 This should enable, among other things, proper JFFS2 operation on 263 these devices. 264 265config MTD_NAND_DISKONCHIP_PROBE_ADVANCED 266 bool "Advanced detection options for DiskOnChip" 267 depends on MTD_NAND_DISKONCHIP 268 help 269 This option allows you to specify nonstandard address at which to 270 probe for a DiskOnChip, or to change the detection options. You 271 are unlikely to need any of this unless you are using LinuxBIOS. 272 Say 'N'. 273 274config MTD_NAND_DISKONCHIP_PROBE_ADDRESS 275 hex "Physical address of DiskOnChip" if MTD_NAND_DISKONCHIP_PROBE_ADVANCED 276 depends on MTD_NAND_DISKONCHIP 277 default "0" 278 ---help--- 279 By default, the probe for DiskOnChip devices will look for a 280 DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000. 281 This option allows you to specify a single address at which to probe 282 for the device, which is useful if you have other devices in that 283 range which get upset when they are probed. 284 285 (Note that on PowerPC, the normal probe will only check at 286 0xE4000000.) 287 288 Normally, you should leave this set to zero, to allow the probe at 289 the normal addresses. 290 291config MTD_NAND_DISKONCHIP_PROBE_HIGH 292 bool "Probe high addresses" 293 depends on MTD_NAND_DISKONCHIP_PROBE_ADVANCED 294 help 295 By default, the probe for DiskOnChip devices will look for a 296 DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000. 297 This option changes to make it probe between 0xFFFC8000 and 298 0xFFFEE000. Unless you are using LinuxBIOS, this is unlikely to be 299 useful to you. Say 'N'. 300 301config MTD_NAND_DISKONCHIP_BBTWRITE 302 bool "Allow BBT writes on DiskOnChip Millennium and 2000TSOP" 303 depends on MTD_NAND_DISKONCHIP 304 help 305 On DiskOnChip devices shipped with the INFTL filesystem (Millennium 306 and 2000 TSOP/Alon), Linux reserves some space at the end of the 307 device for the Bad Block Table (BBT). If you have existing INFTL 308 data on your device (created by non-Linux tools such as M-Systems' 309 DOS drivers), your data might overlap the area Linux wants to use for 310 the BBT. If this is a concern for you, leave this option disabled and 311 Linux will not write BBT data into this area. 312 The downside of leaving this option disabled is that if bad blocks 313 are detected by Linux, they will not be recorded in the BBT, which 314 could cause future problems. 315 Once you enable this option, new filesystems (INFTL or others, created 316 in Linux or other operating systems) will not use the reserved area. 317 The only reason not to enable this option is to prevent damage to 318 preexisting filesystems. 319 Even if you leave this disabled, you can enable BBT writes at module 320 load time (assuming you build diskonchip as a module) with the module 321 parameter "inftl_bbt_write=1". 322 323config MTD_NAND_SHARPSL 324 tristate "Support for NAND Flash on Sharp SL Series (C7xx + others)" 325 depends on ARCH_PXA 326 327config MTD_NAND_CAFE 328 tristate "NAND support for OLPC CAFÉ chip" 329 depends on PCI 330 select REED_SOLOMON 331 select REED_SOLOMON_DEC16 332 help 333 Use NAND flash attached to the CAFÉ chip designed for the OLPC 334 laptop. 335 336config MTD_NAND_CS553X 337 tristate "NAND support for CS5535/CS5536 (AMD Geode companion chip)" 338 depends on X86_32 339 help 340 The CS553x companion chips for the AMD Geode processor 341 include NAND flash controllers with built-in hardware ECC 342 capabilities; enabling this option will allow you to use 343 these. The driver will check the MSRs to verify that the 344 controller is enabled for NAND, and currently requires that 345 the controller be in MMIO mode. 346 347 If you say "m", the module will be called cs553x_nand. 348 349config MTD_NAND_ATMEL 350 tristate "Support for NAND Flash / SmartMedia on AT91 and AVR32" 351 depends on ARCH_AT91 || AVR32 352 help 353 Enables support for NAND Flash / Smart Media Card interface 354 on Atmel AT91 and AVR32 processors. 355choice 356 prompt "ECC management for NAND Flash / SmartMedia on AT91 / AVR32" 357 depends on MTD_NAND_ATMEL 358 359config MTD_NAND_ATMEL_ECC_HW 360 bool "Hardware ECC" 361 depends on ARCH_AT91SAM9263 || ARCH_AT91SAM9260 || AVR32 362 help 363 Use hardware ECC instead of software ECC when the chip 364 supports it. 365 366 The hardware ECC controller is capable of single bit error 367 correction and 2-bit random detection per page. 368 369 NB : hardware and software ECC schemes are incompatible. 370 If you switch from one to another, you'll have to erase your 371 mtd partition. 372 373 If unsure, say Y 374 375config MTD_NAND_ATMEL_ECC_SOFT 376 bool "Software ECC" 377 help 378 Use software ECC. 379 380 NB : hardware and software ECC schemes are incompatible. 381 If you switch from one to another, you'll have to erase your 382 mtd partition. 383 384config MTD_NAND_ATMEL_ECC_NONE 385 bool "No ECC (testing only, DANGEROUS)" 386 depends on DEBUG_KERNEL 387 help 388 No ECC will be used. 389 It's not a good idea and it should be reserved for testing 390 purpose only. 391 392 If unsure, say N 393 394endchoice 395 396config MTD_NAND_PXA3xx 397 tristate "Support for NAND flash devices on PXA3xx" 398 depends on MTD_NAND && (PXA3xx || ARCH_MMP) 399 help 400 This enables the driver for the NAND flash device found on 401 PXA3xx processors 402 403config MTD_NAND_PXA3xx_BUILTIN 404 bool "Use builtin definitions for some NAND chips (deprecated)" 405 depends on MTD_NAND_PXA3xx 406 help 407 This enables builtin definitions for some NAND chips. This 408 is deprecated in favor of platform specific data. 409 410config MTD_NAND_CM_X270 411 tristate "Support for NAND Flash on CM-X270 modules" 412 depends on MTD_NAND && MACH_ARMCORE 413 414config MTD_NAND_PASEMI 415 tristate "NAND support for PA Semi PWRficient" 416 depends on MTD_NAND && PPC_PASEMI 417 help 418 Enables support for NAND Flash interface on PA Semi PWRficient 419 based boards 420 421config MTD_NAND_TMIO 422 tristate "NAND Flash device on Toshiba Mobile IO Controller" 423 depends on MTD_NAND && MFD_TMIO 424 help 425 Support for NAND flash connected to a Toshiba Mobile IO 426 Controller in some PDAs, including the Sharp SL6000x. 427 428config MTD_NAND_NANDSIM 429 tristate "Support for NAND Flash Simulator" 430 depends on MTD_PARTITIONS 431 help 432 The simulator may simulate various NAND flash chips for the 433 MTD nand layer. 434 435config MTD_NAND_PLATFORM 436 tristate "Support for generic platform NAND driver" 437 depends on MTD_NAND 438 help 439 This implements a generic NAND driver for on-SOC platform 440 devices. You will need to provide platform-specific functions 441 via platform_data. 442 443config MTD_ALAUDA 444 tristate "MTD driver for Olympus MAUSB-10 and Fujifilm DPC-R1" 445 depends on MTD_NAND && USB 446 help 447 These two (and possibly other) Alauda-based cardreaders for 448 SmartMedia and xD allow raw flash access. 449 450config MTD_NAND_ORION 451 tristate "NAND Flash support for Marvell Orion SoC" 452 depends on PLAT_ORION && MTD_NAND 453 help 454 This enables the NAND flash controller on Orion machines. 455 456 No board specific support is done by this driver, each board 457 must advertise a platform_device for the driver to attach. 458 459config MTD_NAND_FSL_ELBC 460 tristate "NAND support for Freescale eLBC controllers" 461 depends on MTD_NAND && PPC_OF 462 help 463 Various Freescale chips, including the 8313, include a NAND Flash 464 Controller Module with built-in hardware ECC capabilities. 465 Enabling this option will enable you to use this to control 466 external NAND devices. 467 468config MTD_NAND_FSL_UPM 469 tristate "Support for NAND on Freescale UPM" 470 depends on MTD_NAND && (PPC_83xx || PPC_85xx) 471 select FSL_LBC 472 help 473 Enables support for NAND Flash chips wired onto Freescale PowerPC 474 processor localbus with User-Programmable Machine support. 475 476config MTD_NAND_MPC5121_NFC 477 tristate "MPC5121 built-in NAND Flash Controller support" 478 depends on PPC_MPC512x 479 help 480 This enables the driver for the NAND flash controller on the 481 MPC5121 SoC. 482 483config MTD_NAND_MXC 484 tristate "MXC NAND support" 485 depends on ARCH_MX2 || ARCH_MX25 || ARCH_MX3 486 help 487 This enables the driver for the NAND flash controller on the 488 MXC processors. 489 490config MTD_NAND_NOMADIK 491 tristate "ST Nomadik 8815 NAND support" 492 depends on ARCH_NOMADIK 493 help 494 Driver for the NAND flash controller on the Nomadik, with ECC. 495 496config MTD_NAND_SH_FLCTL 497 tristate "Support for NAND on Renesas SuperH FLCTL" 498 depends on MTD_NAND && (SUPERH || ARCH_SHMOBILE) 499 help 500 Several Renesas SuperH CPU has FLCTL. This option enables support 501 for NAND Flash using FLCTL. 502 503config MTD_NAND_DAVINCI 504 tristate "Support NAND on DaVinci SoC" 505 depends on ARCH_DAVINCI 506 help 507 Enable the driver for NAND flash chips on Texas Instruments 508 DaVinci processors. 509 510config MTD_NAND_TXX9NDFMC 511 tristate "NAND Flash support for TXx9 SoC" 512 depends on SOC_TX4938 || SOC_TX4939 513 help 514 This enables the NAND flash controller on the TXx9 SoCs. 515 516config MTD_NAND_SOCRATES 517 tristate "Support for NAND on Socrates board" 518 depends on MTD_NAND && SOCRATES 519 help 520 Enables support for NAND Flash chips wired onto Socrates board. 521 522config MTD_NAND_NUC900 523 tristate "Support for NAND on Nuvoton NUC9xx/w90p910 evaluation boards." 524 depends on ARCH_W90X900 && MTD_PARTITIONS 525 help 526 This enables the driver for the NAND Flash on evaluation board based 527 on w90p910 / NUC9xx. 528 529endif # MTD_NAND 530