1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Copyright (C) 2010 Marvell International Ltd. 4 * Zhangfei Gao <zhangfei.gao@marvell.com> 5 * Kevin Wang <dwang4@marvell.com> 6 * Mingwei Wang <mwwang@marvell.com> 7 * Philip Rakity <prakity@marvell.com> 8 * Mark Brown <markb@marvell.com> 9 */ 10 #include <linux/err.h> 11 #include <linux/init.h> 12 #include <linux/platform_device.h> 13 #include <linux/clk.h> 14 #include <linux/io.h> 15 #include <linux/mmc/card.h> 16 #include <linux/mmc/host.h> 17 #include <linux/platform_data/pxa_sdhci.h> 18 #include <linux/slab.h> 19 #include <linux/delay.h> 20 #include <linux/module.h> 21 #include <linux/of.h> 22 #include <linux/of_device.h> 23 #include <linux/pm.h> 24 #include <linux/pm_runtime.h> 25 #include <linux/mbus.h> 26 27 #include "sdhci.h" 28 #include "sdhci-pltfm.h" 29 30 #define PXAV3_RPM_DELAY_MS 50 31 32 #define SD_CLOCK_BURST_SIZE_SETUP 0x10A 33 #define SDCLK_SEL 0x100 34 #define SDCLK_DELAY_SHIFT 9 35 #define SDCLK_DELAY_MASK 0x1f 36 37 #define SD_CFG_FIFO_PARAM 0x100 38 #define SDCFG_GEN_PAD_CLK_ON (1<<6) 39 #define SDCFG_GEN_PAD_CLK_CNT_MASK 0xFF 40 #define SDCFG_GEN_PAD_CLK_CNT_SHIFT 24 41 42 #define SD_SPI_MODE 0x108 43 #define SD_CE_ATA_1 0x10C 44 45 #define SD_CE_ATA_2 0x10E 46 #define SDCE_MISC_INT (1<<2) 47 #define SDCE_MISC_INT_EN (1<<1) 48 49 struct sdhci_pxa { 50 struct clk *clk_core; 51 struct clk *clk_io; 52 u8 power_mode; 53 void __iomem *sdio3_conf_reg; 54 }; 55 56 /* 57 * These registers are relative to the second register region, for the 58 * MBus bridge. 59 */ 60 #define SDHCI_WINDOW_CTRL(i) (0x80 + ((i) << 3)) 61 #define SDHCI_WINDOW_BASE(i) (0x84 + ((i) << 3)) 62 #define SDHCI_MAX_WIN_NUM 8 63 64 /* 65 * Fields below belong to SDIO3 Configuration Register (third register 66 * region for the Armada 38x flavor) 67 */ 68 69 #define SDIO3_CONF_CLK_INV BIT(0) 70 #define SDIO3_CONF_SD_FB_CLK BIT(2) 71 72 static int mv_conf_mbus_windows(struct platform_device *pdev, 73 const struct mbus_dram_target_info *dram) 74 { 75 int i; 76 void __iomem *regs; 77 struct resource *res; 78 79 if (!dram) { 80 dev_err(&pdev->dev, "no mbus dram info\n"); 81 return -EINVAL; 82 } 83 84 res = platform_get_resource(pdev, IORESOURCE_MEM, 1); 85 if (!res) { 86 dev_err(&pdev->dev, "cannot get mbus registers\n"); 87 return -EINVAL; 88 } 89 90 regs = ioremap(res->start, resource_size(res)); 91 if (!regs) { 92 dev_err(&pdev->dev, "cannot map mbus registers\n"); 93 return -ENOMEM; 94 } 95 96 for (i = 0; i < SDHCI_MAX_WIN_NUM; i++) { 97 writel(0, regs + SDHCI_WINDOW_CTRL(i)); 98 writel(0, regs + SDHCI_WINDOW_BASE(i)); 99 } 100 101 for (i = 0; i < dram->num_cs; i++) { 102 const struct mbus_dram_window *cs = dram->cs + i; 103 104 /* Write size, attributes and target id to control register */ 105 writel(((cs->size - 1) & 0xffff0000) | 106 (cs->mbus_attr << 8) | 107 (dram->mbus_dram_target_id << 4) | 1, 108 regs + SDHCI_WINDOW_CTRL(i)); 109 /* Write base address to base register */ 110 writel(cs->base, regs + SDHCI_WINDOW_BASE(i)); 111 } 112 113 iounmap(regs); 114 115 return 0; 116 } 117 118 static int armada_38x_quirks(struct platform_device *pdev, 119 struct sdhci_host *host) 120 { 121 struct device_node *np = pdev->dev.of_node; 122 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 123 struct sdhci_pxa *pxa = sdhci_pltfm_priv(pltfm_host); 124 struct resource *res; 125 126 host->quirks &= ~SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN; 127 128 sdhci_read_caps(host); 129 130 res = platform_get_resource_byname(pdev, IORESOURCE_MEM, 131 "conf-sdio3"); 132 if (res) { 133 pxa->sdio3_conf_reg = devm_ioremap_resource(&pdev->dev, res); 134 if (IS_ERR(pxa->sdio3_conf_reg)) 135 return PTR_ERR(pxa->sdio3_conf_reg); 136 } else { 137 /* 138 * According to erratum 'FE-2946959' both SDR50 and DDR50 139 * modes require specific clock adjustments in SDIO3 140 * Configuration register, if the adjustment is not done, 141 * remove them from the capabilities. 142 */ 143 host->caps1 &= ~(SDHCI_SUPPORT_SDR50 | SDHCI_SUPPORT_DDR50); 144 145 dev_warn(&pdev->dev, "conf-sdio3 register not found: disabling SDR50 and DDR50 modes.\nConsider updating your dtb\n"); 146 } 147 148 /* 149 * According to erratum 'ERR-7878951' Armada 38x SDHCI 150 * controller has different capabilities than the ones shown 151 * in its registers 152 */ 153 if (of_property_read_bool(np, "no-1-8-v")) { 154 host->caps &= ~SDHCI_CAN_VDD_180; 155 host->mmc->caps &= ~MMC_CAP_1_8V_DDR; 156 } else { 157 host->caps &= ~SDHCI_CAN_VDD_330; 158 } 159 host->caps1 &= ~(SDHCI_SUPPORT_SDR104 | SDHCI_USE_SDR50_TUNING); 160 161 return 0; 162 } 163 164 static void pxav3_reset(struct sdhci_host *host, u8 mask) 165 { 166 struct platform_device *pdev = to_platform_device(mmc_dev(host->mmc)); 167 struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data; 168 169 sdhci_reset(host, mask); 170 171 if (mask == SDHCI_RESET_ALL) { 172 /* 173 * tune timing of read data/command when crc error happen 174 * no performance impact 175 */ 176 if (pdata && 0 != pdata->clk_delay_cycles) { 177 u16 tmp; 178 179 tmp = readw(host->ioaddr + SD_CLOCK_BURST_SIZE_SETUP); 180 tmp |= (pdata->clk_delay_cycles & SDCLK_DELAY_MASK) 181 << SDCLK_DELAY_SHIFT; 182 tmp |= SDCLK_SEL; 183 writew(tmp, host->ioaddr + SD_CLOCK_BURST_SIZE_SETUP); 184 } 185 } 186 } 187 188 #define MAX_WAIT_COUNT 5 189 static void pxav3_gen_init_74_clocks(struct sdhci_host *host, u8 power_mode) 190 { 191 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 192 struct sdhci_pxa *pxa = sdhci_pltfm_priv(pltfm_host); 193 u16 tmp; 194 int count; 195 196 if (pxa->power_mode == MMC_POWER_UP 197 && power_mode == MMC_POWER_ON) { 198 199 dev_dbg(mmc_dev(host->mmc), 200 "%s: slot->power_mode = %d," 201 "ios->power_mode = %d\n", 202 __func__, 203 pxa->power_mode, 204 power_mode); 205 206 /* set we want notice of when 74 clocks are sent */ 207 tmp = readw(host->ioaddr + SD_CE_ATA_2); 208 tmp |= SDCE_MISC_INT_EN; 209 writew(tmp, host->ioaddr + SD_CE_ATA_2); 210 211 /* start sending the 74 clocks */ 212 tmp = readw(host->ioaddr + SD_CFG_FIFO_PARAM); 213 tmp |= SDCFG_GEN_PAD_CLK_ON; 214 writew(tmp, host->ioaddr + SD_CFG_FIFO_PARAM); 215 216 /* slowest speed is about 100KHz or 10usec per clock */ 217 udelay(740); 218 count = 0; 219 220 while (count++ < MAX_WAIT_COUNT) { 221 if ((readw(host->ioaddr + SD_CE_ATA_2) 222 & SDCE_MISC_INT) == 0) 223 break; 224 udelay(10); 225 } 226 227 if (count == MAX_WAIT_COUNT) 228 dev_warn(mmc_dev(host->mmc), "74 clock interrupt not cleared\n"); 229 230 /* clear the interrupt bit if posted */ 231 tmp = readw(host->ioaddr + SD_CE_ATA_2); 232 tmp |= SDCE_MISC_INT; 233 writew(tmp, host->ioaddr + SD_CE_ATA_2); 234 } 235 pxa->power_mode = power_mode; 236 } 237 238 static void pxav3_set_uhs_signaling(struct sdhci_host *host, unsigned int uhs) 239 { 240 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 241 struct sdhci_pxa *pxa = sdhci_pltfm_priv(pltfm_host); 242 u16 ctrl_2; 243 244 /* 245 * Set V18_EN -- UHS modes do not work without this. 246 * does not change signaling voltage 247 */ 248 ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2); 249 250 /* Select Bus Speed Mode for host */ 251 ctrl_2 &= ~SDHCI_CTRL_UHS_MASK; 252 switch (uhs) { 253 case MMC_TIMING_UHS_SDR12: 254 ctrl_2 |= SDHCI_CTRL_UHS_SDR12; 255 break; 256 case MMC_TIMING_UHS_SDR25: 257 ctrl_2 |= SDHCI_CTRL_UHS_SDR25; 258 break; 259 case MMC_TIMING_UHS_SDR50: 260 ctrl_2 |= SDHCI_CTRL_UHS_SDR50 | SDHCI_CTRL_VDD_180; 261 break; 262 case MMC_TIMING_UHS_SDR104: 263 ctrl_2 |= SDHCI_CTRL_UHS_SDR104 | SDHCI_CTRL_VDD_180; 264 break; 265 case MMC_TIMING_MMC_DDR52: 266 case MMC_TIMING_UHS_DDR50: 267 ctrl_2 |= SDHCI_CTRL_UHS_DDR50 | SDHCI_CTRL_VDD_180; 268 break; 269 } 270 271 /* 272 * Update SDIO3 Configuration register according to erratum 273 * FE-2946959 274 */ 275 if (pxa->sdio3_conf_reg) { 276 u8 reg_val = readb(pxa->sdio3_conf_reg); 277 278 if (uhs == MMC_TIMING_UHS_SDR50 || 279 uhs == MMC_TIMING_UHS_DDR50) { 280 reg_val &= ~SDIO3_CONF_CLK_INV; 281 reg_val |= SDIO3_CONF_SD_FB_CLK; 282 } else if (uhs == MMC_TIMING_MMC_HS) { 283 reg_val &= ~SDIO3_CONF_CLK_INV; 284 reg_val &= ~SDIO3_CONF_SD_FB_CLK; 285 } else { 286 reg_val |= SDIO3_CONF_CLK_INV; 287 reg_val &= ~SDIO3_CONF_SD_FB_CLK; 288 } 289 writeb(reg_val, pxa->sdio3_conf_reg); 290 } 291 292 sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2); 293 dev_dbg(mmc_dev(host->mmc), 294 "%s uhs = %d, ctrl_2 = %04X\n", 295 __func__, uhs, ctrl_2); 296 } 297 298 static void pxav3_set_power(struct sdhci_host *host, unsigned char mode, 299 unsigned short vdd) 300 { 301 struct mmc_host *mmc = host->mmc; 302 u8 pwr = host->pwr; 303 304 sdhci_set_power_noreg(host, mode, vdd); 305 306 if (host->pwr == pwr) 307 return; 308 309 if (host->pwr == 0) 310 vdd = 0; 311 312 if (!IS_ERR(mmc->supply.vmmc)) 313 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, vdd); 314 } 315 316 static const struct sdhci_ops pxav3_sdhci_ops = { 317 .set_clock = sdhci_set_clock, 318 .set_power = pxav3_set_power, 319 .platform_send_init_74_clocks = pxav3_gen_init_74_clocks, 320 .get_max_clock = sdhci_pltfm_clk_get_max_clock, 321 .set_bus_width = sdhci_set_bus_width, 322 .reset = pxav3_reset, 323 .set_uhs_signaling = pxav3_set_uhs_signaling, 324 }; 325 326 static const struct sdhci_pltfm_data sdhci_pxav3_pdata = { 327 .quirks = SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK 328 | SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC 329 | SDHCI_QUIRK_32BIT_ADMA_SIZE 330 | SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN, 331 .ops = &pxav3_sdhci_ops, 332 }; 333 334 #ifdef CONFIG_OF 335 static const struct of_device_id sdhci_pxav3_of_match[] = { 336 { 337 .compatible = "mrvl,pxav3-mmc", 338 }, 339 { 340 .compatible = "marvell,armada-380-sdhci", 341 }, 342 {}, 343 }; 344 MODULE_DEVICE_TABLE(of, sdhci_pxav3_of_match); 345 346 static struct sdhci_pxa_platdata *pxav3_get_mmc_pdata(struct device *dev) 347 { 348 struct sdhci_pxa_platdata *pdata; 349 struct device_node *np = dev->of_node; 350 u32 clk_delay_cycles; 351 352 pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL); 353 if (!pdata) 354 return NULL; 355 356 if (!of_property_read_u32(np, "mrvl,clk-delay-cycles", 357 &clk_delay_cycles)) 358 pdata->clk_delay_cycles = clk_delay_cycles; 359 360 return pdata; 361 } 362 #else 363 static inline struct sdhci_pxa_platdata *pxav3_get_mmc_pdata(struct device *dev) 364 { 365 return NULL; 366 } 367 #endif 368 369 static int sdhci_pxav3_probe(struct platform_device *pdev) 370 { 371 struct sdhci_pltfm_host *pltfm_host; 372 struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data; 373 struct device *dev = &pdev->dev; 374 struct device_node *np = pdev->dev.of_node; 375 struct sdhci_host *host = NULL; 376 struct sdhci_pxa *pxa = NULL; 377 const struct of_device_id *match; 378 int ret; 379 380 host = sdhci_pltfm_init(pdev, &sdhci_pxav3_pdata, sizeof(*pxa)); 381 if (IS_ERR(host)) 382 return PTR_ERR(host); 383 384 pltfm_host = sdhci_priv(host); 385 pxa = sdhci_pltfm_priv(pltfm_host); 386 387 pxa->clk_io = devm_clk_get(dev, "io"); 388 if (IS_ERR(pxa->clk_io)) 389 pxa->clk_io = devm_clk_get(dev, NULL); 390 if (IS_ERR(pxa->clk_io)) { 391 dev_err(dev, "failed to get io clock\n"); 392 ret = PTR_ERR(pxa->clk_io); 393 goto err_clk_get; 394 } 395 pltfm_host->clk = pxa->clk_io; 396 clk_prepare_enable(pxa->clk_io); 397 398 pxa->clk_core = devm_clk_get(dev, "core"); 399 if (!IS_ERR(pxa->clk_core)) 400 clk_prepare_enable(pxa->clk_core); 401 402 /* enable 1/8V DDR capable */ 403 host->mmc->caps |= MMC_CAP_1_8V_DDR; 404 405 if (of_device_is_compatible(np, "marvell,armada-380-sdhci")) { 406 ret = armada_38x_quirks(pdev, host); 407 if (ret < 0) 408 goto err_mbus_win; 409 ret = mv_conf_mbus_windows(pdev, mv_mbus_dram_info()); 410 if (ret < 0) 411 goto err_mbus_win; 412 } 413 414 match = of_match_device(of_match_ptr(sdhci_pxav3_of_match), &pdev->dev); 415 if (match) { 416 ret = mmc_of_parse(host->mmc); 417 if (ret) 418 goto err_of_parse; 419 sdhci_get_of_property(pdev); 420 pdata = pxav3_get_mmc_pdata(dev); 421 pdev->dev.platform_data = pdata; 422 } else if (pdata) { 423 /* on-chip device */ 424 if (pdata->flags & PXA_FLAG_CARD_PERMANENT) 425 host->mmc->caps |= MMC_CAP_NONREMOVABLE; 426 427 /* If slot design supports 8 bit data, indicate this to MMC. */ 428 if (pdata->flags & PXA_FLAG_SD_8_BIT_CAPABLE_SLOT) 429 host->mmc->caps |= MMC_CAP_8_BIT_DATA; 430 431 if (pdata->quirks) 432 host->quirks |= pdata->quirks; 433 if (pdata->quirks2) 434 host->quirks2 |= pdata->quirks2; 435 if (pdata->host_caps) 436 host->mmc->caps |= pdata->host_caps; 437 if (pdata->host_caps2) 438 host->mmc->caps2 |= pdata->host_caps2; 439 if (pdata->pm_caps) 440 host->mmc->pm_caps |= pdata->pm_caps; 441 } 442 443 pm_runtime_get_noresume(&pdev->dev); 444 pm_runtime_set_active(&pdev->dev); 445 pm_runtime_set_autosuspend_delay(&pdev->dev, PXAV3_RPM_DELAY_MS); 446 pm_runtime_use_autosuspend(&pdev->dev); 447 pm_runtime_enable(&pdev->dev); 448 pm_suspend_ignore_children(&pdev->dev, 1); 449 450 ret = sdhci_add_host(host); 451 if (ret) 452 goto err_add_host; 453 454 if (host->mmc->pm_caps & MMC_PM_WAKE_SDIO_IRQ) 455 device_init_wakeup(&pdev->dev, 1); 456 457 pm_runtime_put_autosuspend(&pdev->dev); 458 459 return 0; 460 461 err_add_host: 462 pm_runtime_disable(&pdev->dev); 463 pm_runtime_put_noidle(&pdev->dev); 464 err_of_parse: 465 err_mbus_win: 466 clk_disable_unprepare(pxa->clk_io); 467 clk_disable_unprepare(pxa->clk_core); 468 err_clk_get: 469 sdhci_pltfm_free(pdev); 470 return ret; 471 } 472 473 static void sdhci_pxav3_remove(struct platform_device *pdev) 474 { 475 struct sdhci_host *host = platform_get_drvdata(pdev); 476 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 477 struct sdhci_pxa *pxa = sdhci_pltfm_priv(pltfm_host); 478 479 pm_runtime_get_sync(&pdev->dev); 480 pm_runtime_disable(&pdev->dev); 481 pm_runtime_put_noidle(&pdev->dev); 482 483 sdhci_remove_host(host, 1); 484 485 clk_disable_unprepare(pxa->clk_io); 486 clk_disable_unprepare(pxa->clk_core); 487 488 sdhci_pltfm_free(pdev); 489 } 490 491 #ifdef CONFIG_PM_SLEEP 492 static int sdhci_pxav3_suspend(struct device *dev) 493 { 494 int ret; 495 struct sdhci_host *host = dev_get_drvdata(dev); 496 497 pm_runtime_get_sync(dev); 498 if (host->tuning_mode != SDHCI_TUNING_MODE_3) 499 mmc_retune_needed(host->mmc); 500 ret = sdhci_suspend_host(host); 501 pm_runtime_mark_last_busy(dev); 502 pm_runtime_put_autosuspend(dev); 503 504 return ret; 505 } 506 507 static int sdhci_pxav3_resume(struct device *dev) 508 { 509 int ret; 510 struct sdhci_host *host = dev_get_drvdata(dev); 511 512 pm_runtime_get_sync(dev); 513 ret = sdhci_resume_host(host); 514 pm_runtime_mark_last_busy(dev); 515 pm_runtime_put_autosuspend(dev); 516 517 return ret; 518 } 519 #endif 520 521 #ifdef CONFIG_PM 522 static int sdhci_pxav3_runtime_suspend(struct device *dev) 523 { 524 struct sdhci_host *host = dev_get_drvdata(dev); 525 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 526 struct sdhci_pxa *pxa = sdhci_pltfm_priv(pltfm_host); 527 int ret; 528 529 ret = sdhci_runtime_suspend_host(host); 530 if (ret) 531 return ret; 532 533 if (host->tuning_mode != SDHCI_TUNING_MODE_3) 534 mmc_retune_needed(host->mmc); 535 536 clk_disable_unprepare(pxa->clk_io); 537 if (!IS_ERR(pxa->clk_core)) 538 clk_disable_unprepare(pxa->clk_core); 539 540 return 0; 541 } 542 543 static int sdhci_pxav3_runtime_resume(struct device *dev) 544 { 545 struct sdhci_host *host = dev_get_drvdata(dev); 546 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 547 struct sdhci_pxa *pxa = sdhci_pltfm_priv(pltfm_host); 548 549 clk_prepare_enable(pxa->clk_io); 550 if (!IS_ERR(pxa->clk_core)) 551 clk_prepare_enable(pxa->clk_core); 552 553 return sdhci_runtime_resume_host(host, 0); 554 } 555 #endif 556 557 static const struct dev_pm_ops sdhci_pxav3_pmops = { 558 SET_SYSTEM_SLEEP_PM_OPS(sdhci_pxav3_suspend, sdhci_pxav3_resume) 559 SET_RUNTIME_PM_OPS(sdhci_pxav3_runtime_suspend, 560 sdhci_pxav3_runtime_resume, NULL) 561 }; 562 563 static struct platform_driver sdhci_pxav3_driver = { 564 .driver = { 565 .name = "sdhci-pxav3", 566 .probe_type = PROBE_PREFER_ASYNCHRONOUS, 567 .of_match_table = of_match_ptr(sdhci_pxav3_of_match), 568 .pm = &sdhci_pxav3_pmops, 569 }, 570 .probe = sdhci_pxav3_probe, 571 .remove = sdhci_pxav3_remove, 572 }; 573 574 module_platform_driver(sdhci_pxav3_driver); 575 576 MODULE_DESCRIPTION("SDHCI driver for pxav3"); 577 MODULE_AUTHOR("Marvell International Ltd."); 578 MODULE_LICENSE("GPL v2"); 579 580