xref: /linux/drivers/mmc/host/sdhci-msm.c (revision e814f3fd16acfb7f9966773953de8f740a1e3202)

// SPDX-License-Identifier: GPL-2.0-only
/*
 * drivers/mmc/host/sdhci-msm.c - Qualcomm SDHCI Platform driver
 *
 * Copyright (c) 2013-2014, The Linux Foundation. All rights reserved.
 */

#include <linux/module.h>
#include <linux/delay.h>
#include <linux/mmc/mmc.h>
#include <linux/pm_runtime.h>
#include <linux/pm_opp.h>
#include <linux/slab.h>
#include <linux/iopoll.h>
#include <linux/regulator/consumer.h>
#include <linux/interconnect.h>
#include <linux/of.h>
#include <linux/pinctrl/consumer.h>
#include <linux/reset.h>

#include <soc/qcom/ice.h>

#include "sdhci-cqhci.h"
#include "sdhci-pltfm.h"
#include "cqhci.h"

#define CORE_MCI_VERSION		0x50
#define CORE_VERSION_MAJOR_SHIFT	28
#define CORE_VERSION_MAJOR_MASK		(0xf << CORE_VERSION_MAJOR_SHIFT)
#define CORE_VERSION_MINOR_MASK		0xff

#define CORE_MCI_GENERICS		0x70
#define SWITCHABLE_SIGNALING_VOLTAGE	BIT(29)

#define HC_MODE_EN		0x1
#define CORE_POWER		0x0
#define CORE_SW_RST		BIT(7)
#define FF_CLK_SW_RST_DIS	BIT(13)

#define CORE_PWRCTL_BUS_OFF	BIT(0)
#define CORE_PWRCTL_BUS_ON	BIT(1)
#define CORE_PWRCTL_IO_LOW	BIT(2)
#define CORE_PWRCTL_IO_HIGH	BIT(3)
#define CORE_PWRCTL_BUS_SUCCESS BIT(0)
#define CORE_PWRCTL_BUS_FAIL    BIT(1)
#define CORE_PWRCTL_IO_SUCCESS	BIT(2)
#define CORE_PWRCTL_IO_FAIL     BIT(3)
#define REQ_BUS_OFF		BIT(0)
#define REQ_BUS_ON		BIT(1)
#define REQ_IO_LOW		BIT(2)
#define REQ_IO_HIGH		BIT(3)
#define INT_MASK		0xf
#define MAX_PHASES		16
#define CORE_DLL_LOCK		BIT(7)
#define CORE_DDR_DLL_LOCK	BIT(11)
#define CORE_DLL_EN		BIT(16)
#define CORE_CDR_EN		BIT(17)
#define CORE_CK_OUT_EN		BIT(18)
#define CORE_CDR_EXT_EN		BIT(19)
#define CORE_DLL_PDN		BIT(29)
#define CORE_DLL_RST		BIT(30)
#define CORE_CMD_DAT_TRACK_SEL	BIT(0)

#define CORE_DDR_CAL_EN		BIT(0)
#define CORE_FLL_CYCLE_CNT	BIT(18)
#define CORE_DLL_CLOCK_DISABLE	BIT(21)

#define DLL_USR_CTL_POR_VAL	0x10800
#define ENABLE_DLL_LOCK_STATUS	BIT(26)
#define FINE_TUNE_MODE_EN	BIT(27)
#define BIAS_OK_SIGNAL		BIT(29)

#define DLL_CONFIG_3_LOW_FREQ_VAL	0x08
#define DLL_CONFIG_3_HIGH_FREQ_VAL	0x10

#define CORE_VENDOR_SPEC_POR_VAL 0xa9c
#define CORE_CLK_PWRSAVE	BIT(1)
#define CORE_HC_MCLK_SEL_DFLT	(2 << 8)
#define CORE_HC_MCLK_SEL_HS400	(3 << 8)
#define CORE_HC_MCLK_SEL_MASK	(3 << 8)
#define CORE_IO_PAD_PWR_SWITCH_EN	BIT(15)
#define CORE_IO_PAD_PWR_SWITCH	BIT(16)
#define CORE_HC_SELECT_IN_EN	BIT(18)
#define CORE_HC_SELECT_IN_HS400	(6 << 19)
#define CORE_HC_SELECT_IN_MASK	(7 << 19)

#define CORE_3_0V_SUPPORT	BIT(25)
#define CORE_1_8V_SUPPORT	BIT(26)
#define CORE_VOLT_SUPPORT	(CORE_3_0V_SUPPORT | CORE_1_8V_SUPPORT)

#define CORE_CSR_CDC_CTLR_CFG0		0x130
#define CORE_SW_TRIG_FULL_CALIB		BIT(16)
#define CORE_HW_AUTOCAL_ENA		BIT(17)

#define CORE_CSR_CDC_CTLR_CFG1		0x134
#define CORE_CSR_CDC_CAL_TIMER_CFG0	0x138
#define CORE_TIMER_ENA			BIT(16)

#define CORE_CSR_CDC_CAL_TIMER_CFG1	0x13C
#define CORE_CSR_CDC_REFCOUNT_CFG	0x140
#define CORE_CSR_CDC_COARSE_CAL_CFG	0x144
#define CORE_CDC_OFFSET_CFG		0x14C
#define CORE_CSR_CDC_DELAY_CFG		0x150
#define CORE_CDC_SLAVE_DDA_CFG		0x160
#define CORE_CSR_CDC_STATUS0		0x164
#define CORE_CALIBRATION_DONE		BIT(0)

#define CORE_CDC_ERROR_CODE_MASK	0x7000000

#define CORE_CSR_CDC_GEN_CFG		0x178
#define CORE_CDC_SWITCH_BYPASS_OFF	BIT(0)
#define CORE_CDC_SWITCH_RC_EN		BIT(1)

#define CORE_CDC_T4_DLY_SEL		BIT(0)
#define CORE_CMDIN_RCLK_EN		BIT(1)
#define CORE_START_CDC_TRAFFIC		BIT(6)

#define CORE_PWRSAVE_DLL	BIT(3)

#define DDR_CONFIG_POR_VAL	0x80040873


#define INVALID_TUNING_PHASE	-1
#define SDHCI_MSM_MIN_CLOCK	400000
#define CORE_FREQ_100MHZ	(100 * 1000 * 1000)

#define CDR_SELEXT_SHIFT	20
#define CDR_SELEXT_MASK		(0xf << CDR_SELEXT_SHIFT)
#define CMUX_SHIFT_PHASE_SHIFT	24
#define CMUX_SHIFT_PHASE_MASK	(7 << CMUX_SHIFT_PHASE_SHIFT)

#define MSM_MMC_AUTOSUSPEND_DELAY_MS	50

/* Timeout value to avoid infinite waiting for pwr_irq */
#define MSM_PWR_IRQ_TIMEOUT_MS 5000

/* Max load for eMMC Vdd supply */
#define MMC_VMMC_MAX_LOAD_UA	570000

/* Max load for eMMC Vdd-io supply */
#define MMC_VQMMC_MAX_LOAD_UA	325000

/* Max load for SD Vdd supply */
#define SD_VMMC_MAX_LOAD_UA	800000

/* Max load for SD Vdd-io supply */
#define SD_VQMMC_MAX_LOAD_UA	22000

#define msm_host_readl(msm_host, host, offset) \
	msm_host->var_ops->msm_readl_relaxed(host, offset)

#define msm_host_writel(msm_host, val, host, offset) \
	msm_host->var_ops->msm_writel_relaxed(val, host, offset)

/* CQHCI vendor specific registers */
#define CQHCI_VENDOR_CFG1	0xA00
#define CQHCI_VENDOR_DIS_RST_ON_CQ_EN	(0x3 << 13)

struct sdhci_msm_offset {
	u32 core_hc_mode;
	u32 core_mci_data_cnt;
	u32 core_mci_status;
	u32 core_mci_fifo_cnt;
	u32 core_mci_version;
	u32 core_generics;
	u32 core_testbus_config;
	u32 core_testbus_sel2_bit;
	u32 core_testbus_ena;
	u32 core_testbus_sel2;
	u32 core_pwrctl_status;
	u32 core_pwrctl_mask;
	u32 core_pwrctl_clear;
	u32 core_pwrctl_ctl;
	u32 core_sdcc_debug_reg;
	u32 core_dll_config;
	u32 core_dll_status;
	u32 core_vendor_spec;
	u32 core_vendor_spec_adma_err_addr0;
	u32 core_vendor_spec_adma_err_addr1;
	u32 core_vendor_spec_func2;
	u32 core_vendor_spec_capabilities0;
	u32 core_ddr_200_cfg;
	u32 core_vendor_spec3;
	u32 core_dll_config_2;
	u32 core_dll_config_3;
	u32 core_ddr_config_old; /* Applicable to sdcc minor ver < 0x49 */
	u32 core_ddr_config;
	u32 core_dll_usr_ctl; /* Present on SDCC5.1 onwards */
};

static const struct sdhci_msm_offset sdhci_msm_v5_offset = {
	.core_mci_data_cnt = 0x35c,
	.core_mci_status = 0x324,
	.core_mci_fifo_cnt = 0x308,
	.core_mci_version = 0x318,
	.core_generics = 0x320,
	.core_testbus_config = 0x32c,
	.core_testbus_sel2_bit = 3,
	.core_testbus_ena = (1 << 31),
	.core_testbus_sel2 = (1 << 3),
	.core_pwrctl_status = 0x240,
	.core_pwrctl_mask = 0x244,
	.core_pwrctl_clear = 0x248,
	.core_pwrctl_ctl = 0x24c,
	.core_sdcc_debug_reg = 0x358,
	.core_dll_config = 0x200,
	.core_dll_status = 0x208,
	.core_vendor_spec = 0x20c,
	.core_vendor_spec_adma_err_addr0 = 0x214,
	.core_vendor_spec_adma_err_addr1 = 0x218,
	.core_vendor_spec_func2 = 0x210,
	.core_vendor_spec_capabilities0 = 0x21c,
	.core_ddr_200_cfg = 0x224,
	.core_vendor_spec3 = 0x250,
	.core_dll_config_2 = 0x254,
	.core_dll_config_3 = 0x258,
	.core_ddr_config = 0x25c,
	.core_dll_usr_ctl = 0x388,
};

static const struct sdhci_msm_offset sdhci_msm_mci_offset = {
	.core_hc_mode = 0x78,
	.core_mci_data_cnt = 0x30,
	.core_mci_status = 0x34,
	.core_mci_fifo_cnt = 0x44,
	.core_mci_version = 0x050,
	.core_generics = 0x70,
	.core_testbus_config = 0x0cc,
	.core_testbus_sel2_bit = 4,
	.core_testbus_ena = (1 << 3),
	.core_testbus_sel2 = (1 << 4),
	.core_pwrctl_status = 0xdc,
	.core_pwrctl_mask = 0xe0,
	.core_pwrctl_clear = 0xe4,
	.core_pwrctl_ctl = 0xe8,
	.core_sdcc_debug_reg = 0x124,
	.core_dll_config = 0x100,
	.core_dll_status = 0x108,
	.core_vendor_spec = 0x10c,
	.core_vendor_spec_adma_err_addr0 = 0x114,
	.core_vendor_spec_adma_err_addr1 = 0x118,
	.core_vendor_spec_func2 = 0x110,
	.core_vendor_spec_capabilities0 = 0x11c,
	.core_ddr_200_cfg = 0x184,
	.core_vendor_spec3 = 0x1b0,
	.core_dll_config_2 = 0x1b4,
	.core_ddr_config_old = 0x1b8,
	.core_ddr_config = 0x1bc,
};

struct sdhci_msm_variant_ops {
	u32 (*msm_readl_relaxed)(struct sdhci_host *host, u32 offset);
	void (*msm_writel_relaxed)(u32 val, struct sdhci_host *host,
			u32 offset);
};

/*
 * From V5, register spaces have changed. Wrap this info in a structure
 * and choose the data_structure based on version info mentioned in DT.
 */
struct sdhci_msm_variant_info {
	bool mci_removed;
	bool restore_dll_config;
	const struct sdhci_msm_variant_ops *var_ops;
	const struct sdhci_msm_offset *offset;
};

struct sdhci_msm_host {
	struct platform_device *pdev;
	void __iomem *core_mem;	/* MSM SDCC mapped address */
	int pwr_irq;		/* power irq */
	struct clk *bus_clk;	/* SDHC bus voter clock */
	struct clk *xo_clk;	/* TCXO clk needed for FLL feature of cm_dll*/
	/* core, iface, cal and sleep clocks */
	struct clk_bulk_data bulk_clks[4];
#ifdef CONFIG_MMC_CRYPTO
	struct qcom_ice *ice;
#endif
	unsigned long clk_rate;
	struct mmc_host *mmc;
	bool use_14lpp_dll_reset;
	bool tuning_done;
	bool calibration_done;
	u8 saved_tuning_phase;
	bool use_cdclp533;
	u32 curr_pwr_state;
	u32 curr_io_level;
	wait_queue_head_t pwr_irq_wait;
	bool pwr_irq_flag;
	u32 caps_0;
	bool mci_removed;
	bool restore_dll_config;
	const struct sdhci_msm_variant_ops *var_ops;
	const struct sdhci_msm_offset *offset;
	bool use_cdr;
	u32 transfer_mode;
	bool updated_ddr_cfg;
	bool uses_tassadar_dll;
	u32 dll_config;
	u32 ddr_config;
	bool vqmmc_enabled;
};

static const struct sdhci_msm_offset *sdhci_priv_msm_offset(struct sdhci_host *host)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);

	return msm_host->offset;
}

/*
 * APIs to read/write to vendor specific registers which were there in the
 * core_mem region before MCI was removed.
 */
static u32 sdhci_msm_mci_variant_readl_relaxed(struct sdhci_host *host,
		u32 offset)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);

	return readl_relaxed(msm_host->core_mem + offset);
}

static u32 sdhci_msm_v5_variant_readl_relaxed(struct sdhci_host *host,
		u32 offset)
{
	return readl_relaxed(host->ioaddr + offset);
}

static void sdhci_msm_mci_variant_writel_relaxed(u32 val,
		struct sdhci_host *host, u32 offset)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);

	writel_relaxed(val, msm_host->core_mem + offset);
}

static void sdhci_msm_v5_variant_writel_relaxed(u32 val,
		struct sdhci_host *host, u32 offset)
{
	writel_relaxed(val, host->ioaddr + offset);
}

static unsigned int msm_get_clock_mult_for_bus_mode(struct sdhci_host *host)
{
	struct mmc_ios ios = host->mmc->ios;
	/*
	 * The SDHC requires internal clock frequency to be double the
	 * actual clock that will be set for DDR mode. The controller
	 * uses the faster clock(100/400MHz) for some of its parts and
	 * send the actual required clock (50/200MHz) to the card.
	 */
	if (ios.timing == MMC_TIMING_UHS_DDR50 ||
	    ios.timing == MMC_TIMING_MMC_DDR52 ||
	    ios.timing == MMC_TIMING_MMC_HS400 ||
	    host->flags & SDHCI_HS400_TUNING)
		return 2;
	return 1;
}

static void msm_set_clock_rate_for_bus_mode(struct sdhci_host *host,
					    unsigned int clock)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
	struct mmc_ios curr_ios = host->mmc->ios;
	struct clk *core_clk = msm_host->bulk_clks[0].clk;
	unsigned long achieved_rate;
	unsigned int desired_rate;
	unsigned int mult;
	int rc;

	mult = msm_get_clock_mult_for_bus_mode(host);
	desired_rate = clock * mult;
	rc = dev_pm_opp_set_rate(mmc_dev(host->mmc), desired_rate);
	if (rc) {
		pr_err("%s: Failed to set clock at rate %u at timing %d\n",
		       mmc_hostname(host->mmc), desired_rate, curr_ios.timing);
		return;
	}

	/*
	 * Qualcomm clock drivers by default round clock _up_ if they can't
	 * make the requested rate.  This is not good for SD.  Yell if we
	 * encounter it.
	 */
	achieved_rate = clk_get_rate(core_clk);
	if (achieved_rate > desired_rate)
		pr_warn("%s: Card appears overclocked; req %u Hz, actual %lu Hz\n",
			mmc_hostname(host->mmc), desired_rate, achieved_rate);
	host->mmc->actual_clock = achieved_rate / mult;

	/* Stash the rate we requested to use in sdhci_msm_runtime_resume() */
	msm_host->clk_rate = desired_rate;

	pr_debug("%s: Setting clock at rate %lu at timing %d\n",
		 mmc_hostname(host->mmc), achieved_rate, curr_ios.timing);
}

/* Platform specific tuning */
static inline int msm_dll_poll_ck_out_en(struct sdhci_host *host, u8 poll)
{
	u32 wait_cnt = 50;
	u8 ck_out_en;
	struct mmc_host *mmc = host->mmc;
	const struct sdhci_msm_offset *msm_offset =
					sdhci_priv_msm_offset(host);

	/* Poll for CK_OUT_EN bit.  max. poll time = 50us */
	ck_out_en = !!(readl_relaxed(host->ioaddr +
			msm_offset->core_dll_config) & CORE_CK_OUT_EN);

	while (ck_out_en != poll) {
		if (--wait_cnt == 0) {
			dev_err(mmc_dev(mmc), "%s: CK_OUT_EN bit is not %d\n",
			       mmc_hostname(mmc), poll);
			return -ETIMEDOUT;
		}
		udelay(1);

		ck_out_en = !!(readl_relaxed(host->ioaddr +
			msm_offset->core_dll_config) & CORE_CK_OUT_EN);
	}

	return 0;
}

static int msm_config_cm_dll_phase(struct sdhci_host *host, u8 phase)
{
	int rc;
	static const u8 grey_coded_phase_table[] = {
		0x0, 0x1, 0x3, 0x2, 0x6, 0x7, 0x5, 0x4,
		0xc, 0xd, 0xf, 0xe, 0xa, 0xb, 0x9, 0x8
	};
	unsigned long flags;
	u32 config;
	struct mmc_host *mmc = host->mmc;
	const struct sdhci_msm_offset *msm_offset =
					sdhci_priv_msm_offset(host);

	if (phase > 0xf)
		return -EINVAL;

	spin_lock_irqsave(&host->lock, flags);

	config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config);
	config &= ~(CORE_CDR_EN | CORE_CK_OUT_EN);
	config |= (CORE_CDR_EXT_EN | CORE_DLL_EN);
	writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config);

	/* Wait until CK_OUT_EN bit of DLL_CONFIG register becomes '0' */
	rc = msm_dll_poll_ck_out_en(host, 0);
	if (rc)
		goto err_out;

	/*
	 * Write the selected DLL clock output phase (0 ... 15)
	 * to CDR_SELEXT bit field of DLL_CONFIG register.
	 */
	config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config);
	config &= ~CDR_SELEXT_MASK;
	config |= grey_coded_phase_table[phase] << CDR_SELEXT_SHIFT;
	writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config);

	config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config);
	config |= CORE_CK_OUT_EN;
	writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config);

	/* Wait until CK_OUT_EN bit of DLL_CONFIG register becomes '1' */
	rc = msm_dll_poll_ck_out_en(host, 1);
	if (rc)
		goto err_out;

	config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config);
	config |= CORE_CDR_EN;
	config &= ~CORE_CDR_EXT_EN;
	writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config);
	goto out;

err_out:
	dev_err(mmc_dev(mmc), "%s: Failed to set DLL phase: %d\n",
	       mmc_hostname(mmc), phase);
out:
	spin_unlock_irqrestore(&host->lock, flags);
	return rc;
}

/*
 * Find out the greatest range of consecuitive selected
 * DLL clock output phases that can be used as sampling
 * setting for SD3.0 UHS-I card read operation (in SDR104
 * timing mode) or for eMMC4.5 card read operation (in
 * HS400/HS200 timing mode).
 * Select the 3/4 of the range and configure the DLL with the
 * selected DLL clock output phase.
 */

static int msm_find_most_appropriate_phase(struct sdhci_host *host,
					   u8 *phase_table, u8 total_phases)
{
	int ret;
	u8 ranges[MAX_PHASES][MAX_PHASES] = { {0}, {0} };
	u8 phases_per_row[MAX_PHASES] = { 0 };
	int row_index = 0, col_index = 0, selected_row_index = 0, curr_max = 0;
	int i, cnt, phase_0_raw_index = 0, phase_15_raw_index = 0;
	bool phase_0_found = false, phase_15_found = false;
	struct mmc_host *mmc = host->mmc;

	if (!total_phases || (total_phases > MAX_PHASES)) {
		dev_err(mmc_dev(mmc), "%s: Invalid argument: total_phases=%d\n",
		       mmc_hostname(mmc), total_phases);
		return -EINVAL;
	}

	for (cnt = 0; cnt < total_phases; cnt++) {
		ranges[row_index][col_index] = phase_table[cnt];
		phases_per_row[row_index] += 1;
		col_index++;

		if ((cnt + 1) == total_phases) {
			continue;
		/* check if next phase in phase_table is consecutive or not */
		} else if ((phase_table[cnt] + 1) != phase_table[cnt + 1]) {
			row_index++;
			col_index = 0;
		}
	}

	if (row_index >= MAX_PHASES)
		return -EINVAL;

	/* Check if phase-0 is present in first valid window? */
	if (!ranges[0][0]) {
		phase_0_found = true;
		phase_0_raw_index = 0;
		/* Check if cycle exist between 2 valid windows */
		for (cnt = 1; cnt <= row_index; cnt++) {
			if (phases_per_row[cnt]) {
				for (i = 0; i < phases_per_row[cnt]; i++) {
					if (ranges[cnt][i] == 15) {
						phase_15_found = true;
						phase_15_raw_index = cnt;
						break;
					}
				}
			}
		}
	}

	/* If 2 valid windows form cycle then merge them as single window */
	if (phase_0_found && phase_15_found) {
		/* number of phases in raw where phase 0 is present */
		u8 phases_0 = phases_per_row[phase_0_raw_index];
		/* number of phases in raw where phase 15 is present */
		u8 phases_15 = phases_per_row[phase_15_raw_index];

		if (phases_0 + phases_15 >= MAX_PHASES)
			/*
			 * If there are more than 1 phase windows then total
			 * number of phases in both the windows should not be
			 * more than or equal to MAX_PHASES.
			 */
			return -EINVAL;

		/* Merge 2 cyclic windows */
		i = phases_15;
		for (cnt = 0; cnt < phases_0; cnt++) {
			ranges[phase_15_raw_index][i] =
			    ranges[phase_0_raw_index][cnt];
			if (++i >= MAX_PHASES)
				break;
		}

		phases_per_row[phase_0_raw_index] = 0;
		phases_per_row[phase_15_raw_index] = phases_15 + phases_0;
	}

	for (cnt = 0; cnt <= row_index; cnt++) {
		if (phases_per_row[cnt] > curr_max) {
			curr_max = phases_per_row[cnt];
			selected_row_index = cnt;
		}
	}

	i = (curr_max * 3) / 4;
	if (i)
		i--;

	ret = ranges[selected_row_index][i];

	if (ret >= MAX_PHASES) {
		ret = -EINVAL;
		dev_err(mmc_dev(mmc), "%s: Invalid phase selected=%d\n",
		       mmc_hostname(mmc), ret);
	}

	return ret;
}

static inline void msm_cm_dll_set_freq(struct sdhci_host *host)
{
	u32 mclk_freq = 0, config;
	const struct sdhci_msm_offset *msm_offset =
					sdhci_priv_msm_offset(host);

	/* Program the MCLK value to MCLK_FREQ bit field */
	if (host->clock <= 112000000)
		mclk_freq = 0;
	else if (host->clock <= 125000000)
		mclk_freq = 1;
	else if (host->clock <= 137000000)
		mclk_freq = 2;
	else if (host->clock <= 150000000)
		mclk_freq = 3;
	else if (host->clock <= 162000000)
		mclk_freq = 4;
	else if (host->clock <= 175000000)
		mclk_freq = 5;
	else if (host->clock <= 187000000)
		mclk_freq = 6;
	else if (host->clock <= 200000000)
		mclk_freq = 7;

	config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config);
	config &= ~CMUX_SHIFT_PHASE_MASK;
	config |= mclk_freq << CMUX_SHIFT_PHASE_SHIFT;
	writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config);
}

/* Initialize the DLL (Programmable Delay Line) */
static int msm_init_cm_dll(struct sdhci_host *host)
{
	struct mmc_host *mmc = host->mmc;
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
	int wait_cnt = 50;
	unsigned long flags, xo_clk = 0;
	u32 config;
	const struct sdhci_msm_offset *msm_offset =
					msm_host->offset;

	if (msm_host->use_14lpp_dll_reset && !IS_ERR_OR_NULL(msm_host->xo_clk))
		xo_clk = clk_get_rate(msm_host->xo_clk);

	spin_lock_irqsave(&host->lock, flags);

	/*
	 * Make sure that clock is always enabled when DLL
	 * tuning is in progress. Keeping PWRSAVE ON may
	 * turn off the clock.
	 */
	config = readl_relaxed(host->ioaddr + msm_offset->core_vendor_spec);
	config &= ~CORE_CLK_PWRSAVE;
	writel_relaxed(config, host->ioaddr + msm_offset->core_vendor_spec);

	if (msm_host->dll_config)
		writel_relaxed(msm_host->dll_config,
				host->ioaddr + msm_offset->core_dll_config);

	if (msm_host->use_14lpp_dll_reset) {
		config = readl_relaxed(host->ioaddr +
				msm_offset->core_dll_config);
		config &= ~CORE_CK_OUT_EN;
		writel_relaxed(config, host->ioaddr +
				msm_offset->core_dll_config);

		config = readl_relaxed(host->ioaddr +
				msm_offset->core_dll_config_2);
		config |= CORE_DLL_CLOCK_DISABLE;
		writel_relaxed(config, host->ioaddr +
				msm_offset->core_dll_config_2);
	}

	config = readl_relaxed(host->ioaddr +
			msm_offset->core_dll_config);
	config |= CORE_DLL_RST;
	writel_relaxed(config, host->ioaddr +
			msm_offset->core_dll_config);

	config = readl_relaxed(host->ioaddr +
			msm_offset->core_dll_config);
	config |= CORE_DLL_PDN;
	writel_relaxed(config, host->ioaddr +
			msm_offset->core_dll_config);

	if (!msm_host->dll_config)
		msm_cm_dll_set_freq(host);

	if (msm_host->use_14lpp_dll_reset &&
	    !IS_ERR_OR_NULL(msm_host->xo_clk)) {
		u32 mclk_freq = 0;

		config = readl_relaxed(host->ioaddr +
				msm_offset->core_dll_config_2);
		config &= CORE_FLL_CYCLE_CNT;
		if (config)
			mclk_freq = DIV_ROUND_CLOSEST_ULL((host->clock * 8),
					xo_clk);
		else
			mclk_freq = DIV_ROUND_CLOSEST_ULL((host->clock * 4),
					xo_clk);

		config = readl_relaxed(host->ioaddr +
				msm_offset->core_dll_config_2);
		config &= ~(0xFF << 10);
		config |= mclk_freq << 10;

		writel_relaxed(config, host->ioaddr +
				msm_offset->core_dll_config_2);
		/* wait for 5us before enabling DLL clock */
		udelay(5);
	}

	config = readl_relaxed(host->ioaddr +
			msm_offset->core_dll_config);
	config &= ~CORE_DLL_RST;
	writel_relaxed(config, host->ioaddr +
			msm_offset->core_dll_config);

	config = readl_relaxed(host->ioaddr +
			msm_offset->core_dll_config);
	config &= ~CORE_DLL_PDN;
	writel_relaxed(config, host->ioaddr +
			msm_offset->core_dll_config);

	if (msm_host->use_14lpp_dll_reset) {
		if (!msm_host->dll_config)
			msm_cm_dll_set_freq(host);
		config = readl_relaxed(host->ioaddr +
				msm_offset->core_dll_config_2);
		config &= ~CORE_DLL_CLOCK_DISABLE;
		writel_relaxed(config, host->ioaddr +
				msm_offset->core_dll_config_2);
	}

	/*
	 * Configure DLL user control register to enable DLL status.
	 * This setting is applicable to SDCC v5.1 onwards only.
	 */
	if (msm_host->uses_tassadar_dll) {
		config = DLL_USR_CTL_POR_VAL | FINE_TUNE_MODE_EN |
			ENABLE_DLL_LOCK_STATUS | BIAS_OK_SIGNAL;
		writel_relaxed(config, host->ioaddr +
				msm_offset->core_dll_usr_ctl);

		config = readl_relaxed(host->ioaddr +
				msm_offset->core_dll_config_3);
		config &= ~0xFF;
		if (msm_host->clk_rate < 150000000)
			config |= DLL_CONFIG_3_LOW_FREQ_VAL;
		else
			config |= DLL_CONFIG_3_HIGH_FREQ_VAL;
		writel_relaxed(config, host->ioaddr +
			msm_offset->core_dll_config_3);
	}

	config = readl_relaxed(host->ioaddr +
			msm_offset->core_dll_config);
	config |= CORE_DLL_EN;
	writel_relaxed(config, host->ioaddr +
			msm_offset->core_dll_config);

	config = readl_relaxed(host->ioaddr +
			msm_offset->core_dll_config);
	config |= CORE_CK_OUT_EN;
	writel_relaxed(config, host->ioaddr +
			msm_offset->core_dll_config);

	/* Wait until DLL_LOCK bit of DLL_STATUS register becomes '1' */
	while (!(readl_relaxed(host->ioaddr + msm_offset->core_dll_status) &
		 CORE_DLL_LOCK)) {
		/* max. wait for 50us sec for LOCK bit to be set */
		if (--wait_cnt == 0) {
			dev_err(mmc_dev(mmc), "%s: DLL failed to LOCK\n",
			       mmc_hostname(mmc));
			spin_unlock_irqrestore(&host->lock, flags);
			return -ETIMEDOUT;
		}
		udelay(1);
	}

	spin_unlock_irqrestore(&host->lock, flags);
	return 0;
}

static void msm_hc_select_default(struct sdhci_host *host)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
	u32 config;
	const struct sdhci_msm_offset *msm_offset =
					msm_host->offset;

	if (!msm_host->use_cdclp533) {
		config = readl_relaxed(host->ioaddr +
				msm_offset->core_vendor_spec3);
		config &= ~CORE_PWRSAVE_DLL;
		writel_relaxed(config, host->ioaddr +
				msm_offset->core_vendor_spec3);
	}

	config = readl_relaxed(host->ioaddr + msm_offset->core_vendor_spec);
	config &= ~CORE_HC_MCLK_SEL_MASK;
	config |= CORE_HC_MCLK_SEL_DFLT;
	writel_relaxed(config, host->ioaddr + msm_offset->core_vendor_spec);

	/*
	 * Disable HC_SELECT_IN to be able to use the UHS mode select
	 * configuration from Host Control2 register for all other
	 * modes.
	 * Write 0 to HC_SELECT_IN and HC_SELECT_IN_EN field
	 * in VENDOR_SPEC_FUNC
	 */
	config = readl_relaxed(host->ioaddr + msm_offset->core_vendor_spec);
	config &= ~CORE_HC_SELECT_IN_EN;
	config &= ~CORE_HC_SELECT_IN_MASK;
	writel_relaxed(config, host->ioaddr + msm_offset->core_vendor_spec);

	/*
	 * Make sure above writes impacting free running MCLK are completed
	 * before changing the clk_rate at GCC.
	 */
	wmb();
}

static void msm_hc_select_hs400(struct sdhci_host *host)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
	struct mmc_ios ios = host->mmc->ios;
	u32 config, dll_lock;
	int rc;
	const struct sdhci_msm_offset *msm_offset =
					msm_host->offset;

	/* Select the divided clock (free running MCLK/2) */
	config = readl_relaxed(host->ioaddr + msm_offset->core_vendor_spec);
	config &= ~CORE_HC_MCLK_SEL_MASK;
	config |= CORE_HC_MCLK_SEL_HS400;

	writel_relaxed(config, host->ioaddr + msm_offset->core_vendor_spec);
	/*
	 * Select HS400 mode using the HC_SELECT_IN from VENDOR SPEC
	 * register
	 */
	if ((msm_host->tuning_done || ios.enhanced_strobe) &&
	    !msm_host->calibration_done) {
		config = readl_relaxed(host->ioaddr +
				msm_offset->core_vendor_spec);
		config |= CORE_HC_SELECT_IN_HS400;
		config |= CORE_HC_SELECT_IN_EN;
		writel_relaxed(config, host->ioaddr +
				msm_offset->core_vendor_spec);
	}
	if (!msm_host->clk_rate && !msm_host->use_cdclp533) {
		/*
		 * Poll on DLL_LOCK or DDR_DLL_LOCK bits in
		 * core_dll_status to be set. This should get set
		 * within 15 us at 200 MHz.
		 */
		rc = readl_relaxed_poll_timeout(host->ioaddr +
						msm_offset->core_dll_status,
						dll_lock,
						(dll_lock &
						(CORE_DLL_LOCK |
						CORE_DDR_DLL_LOCK)), 10,
						1000);
		if (rc == -ETIMEDOUT)
			pr_err("%s: Unable to get DLL_LOCK/DDR_DLL_LOCK, dll_status: 0x%08x\n",
			       mmc_hostname(host->mmc), dll_lock);
	}
	/*
	 * Make sure above writes impacting free running MCLK are completed
	 * before changing the clk_rate at GCC.
	 */
	wmb();
}

/*
 * sdhci_msm_hc_select_mode :- In general all timing modes are
 * controlled via UHS mode select in Host Control2 register.
 * eMMC specific HS200/HS400 doesn't have their respective modes
 * defined here, hence we use these values.
 *
 * HS200 - SDR104 (Since they both are equivalent in functionality)
 * HS400 - This involves multiple configurations
 *		Initially SDR104 - when tuning is required as HS200
 *		Then when switching to DDR @ 400MHz (HS400) we use
 *		the vendor specific HC_SELECT_IN to control the mode.
 *
 * In addition to controlling the modes we also need to select the
 * correct input clock for DLL depending on the mode.
 *
 * HS400 - divided clock (free running MCLK/2)
 * All other modes - default (free running MCLK)
 */
static void sdhci_msm_hc_select_mode(struct sdhci_host *host)
{
	struct mmc_ios ios = host->mmc->ios;

	if (ios.timing == MMC_TIMING_MMC_HS400 ||
	    host->flags & SDHCI_HS400_TUNING)
		msm_hc_select_hs400(host);
	else
		msm_hc_select_default(host);
}

static int sdhci_msm_cdclp533_calibration(struct sdhci_host *host)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
	u32 config, calib_done;
	int ret;
	const struct sdhci_msm_offset *msm_offset =
					msm_host->offset;

	pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__);

	/*
	 * Retuning in HS400 (DDR mode) will fail, just reset the
	 * tuning block and restore the saved tuning phase.
	 */
	ret = msm_init_cm_dll(host);
	if (ret)
		goto out;

	/* Set the selected phase in delay line hw block */
	ret = msm_config_cm_dll_phase(host, msm_host->saved_tuning_phase);
	if (ret)
		goto out;

	config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config);
	config |= CORE_CMD_DAT_TRACK_SEL;
	writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config);

	config = readl_relaxed(host->ioaddr + msm_offset->core_ddr_200_cfg);
	config &= ~CORE_CDC_T4_DLY_SEL;
	writel_relaxed(config, host->ioaddr + msm_offset->core_ddr_200_cfg);

	config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_GEN_CFG);
	config &= ~CORE_CDC_SWITCH_BYPASS_OFF;
	writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_GEN_CFG);

	config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_GEN_CFG);
	config |= CORE_CDC_SWITCH_RC_EN;
	writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_GEN_CFG);

	config = readl_relaxed(host->ioaddr + msm_offset->core_ddr_200_cfg);
	config &= ~CORE_START_CDC_TRAFFIC;
	writel_relaxed(config, host->ioaddr + msm_offset->core_ddr_200_cfg);

	/* Perform CDC Register Initialization Sequence */

	writel_relaxed(0x11800EC, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
	writel_relaxed(0x3011111, host->ioaddr + CORE_CSR_CDC_CTLR_CFG1);
	writel_relaxed(0x1201000, host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG0);
	writel_relaxed(0x4, host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG1);
	writel_relaxed(0xCB732020, host->ioaddr + CORE_CSR_CDC_REFCOUNT_CFG);
	writel_relaxed(0xB19, host->ioaddr + CORE_CSR_CDC_COARSE_CAL_CFG);
	writel_relaxed(0x4E2, host->ioaddr + CORE_CSR_CDC_DELAY_CFG);
	writel_relaxed(0x0, host->ioaddr + CORE_CDC_OFFSET_CFG);
	writel_relaxed(0x16334, host->ioaddr + CORE_CDC_SLAVE_DDA_CFG);

	/* CDC HW Calibration */

	config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
	config |= CORE_SW_TRIG_FULL_CALIB;
	writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);

	config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
	config &= ~CORE_SW_TRIG_FULL_CALIB;
	writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);

	config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
	config |= CORE_HW_AUTOCAL_ENA;
	writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);

	config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG0);
	config |= CORE_TIMER_ENA;
	writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG0);

	ret = readl_relaxed_poll_timeout(host->ioaddr + CORE_CSR_CDC_STATUS0,
					 calib_done,
					 (calib_done & CORE_CALIBRATION_DONE),
					 1, 50);

	if (ret == -ETIMEDOUT) {
		pr_err("%s: %s: CDC calibration was not completed\n",
		       mmc_hostname(host->mmc), __func__);
		goto out;
	}

	ret = readl_relaxed(host->ioaddr + CORE_CSR_CDC_STATUS0)
			& CORE_CDC_ERROR_CODE_MASK;
	if (ret) {
		pr_err("%s: %s: CDC error code %d\n",
		       mmc_hostname(host->mmc), __func__, ret);
		ret = -EINVAL;
		goto out;
	}

	config = readl_relaxed(host->ioaddr + msm_offset->core_ddr_200_cfg);
	config |= CORE_START_CDC_TRAFFIC;
	writel_relaxed(config, host->ioaddr + msm_offset->core_ddr_200_cfg);
out:
	pr_debug("%s: %s: Exit, ret %d\n", mmc_hostname(host->mmc),
		 __func__, ret);
	return ret;
}

static int sdhci_msm_cm_dll_sdc4_calibration(struct sdhci_host *host)
{
	struct mmc_host *mmc = host->mmc;
	u32 dll_status, config, ddr_cfg_offset;
	int ret;
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
	const struct sdhci_msm_offset *msm_offset =
					sdhci_priv_msm_offset(host);

	pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__);

	/*
	 * Currently the core_ddr_config register defaults to desired
	 * configuration on reset. Currently reprogramming the power on
	 * reset (POR) value in case it might have been modified by
	 * bootloaders. In the future, if this changes, then the desired
	 * values will need to be programmed appropriately.
	 */
	if (msm_host->updated_ddr_cfg)
		ddr_cfg_offset = msm_offset->core_ddr_config;
	else
		ddr_cfg_offset = msm_offset->core_ddr_config_old;
	writel_relaxed(msm_host->ddr_config, host->ioaddr + ddr_cfg_offset);

	if (mmc->ios.enhanced_strobe) {
		config = readl_relaxed(host->ioaddr +
				msm_offset->core_ddr_200_cfg);
		config |= CORE_CMDIN_RCLK_EN;
		writel_relaxed(config, host->ioaddr +
				msm_offset->core_ddr_200_cfg);
	}

	config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config_2);
	config |= CORE_DDR_CAL_EN;
	writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config_2);

	ret = readl_relaxed_poll_timeout(host->ioaddr +
					msm_offset->core_dll_status,
					dll_status,
					(dll_status & CORE_DDR_DLL_LOCK),
					10, 1000);

	if (ret == -ETIMEDOUT) {
		pr_err("%s: %s: CM_DLL_SDC4 calibration was not completed\n",
		       mmc_hostname(host->mmc), __func__);
		goto out;
	}

	/*
	 * Set CORE_PWRSAVE_DLL bit in CORE_VENDOR_SPEC3.
	 * When MCLK is gated OFF, it is not gated for less than 0.5us
	 * and MCLK must be switched on for at-least 1us before DATA
	 * starts coming. Controllers with 14lpp and later tech DLL cannot
	 * guarantee above requirement. So PWRSAVE_DLL should not be
	 * turned on for host controllers using this DLL.
	 */
	if (!msm_host->use_14lpp_dll_reset) {
		config = readl_relaxed(host->ioaddr +
				msm_offset->core_vendor_spec3);
		config |= CORE_PWRSAVE_DLL;
		writel_relaxed(config, host->ioaddr +
				msm_offset->core_vendor_spec3);
	}

	/*
	 * Drain writebuffer to ensure above DLL calibration
	 * and PWRSAVE DLL is enabled.
	 */
	wmb();
out:
	pr_debug("%s: %s: Exit, ret %d\n", mmc_hostname(host->mmc),
		 __func__, ret);
	return ret;
}

static int sdhci_msm_hs400_dll_calibration(struct sdhci_host *host)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
	struct mmc_host *mmc = host->mmc;
	int ret;
	u32 config;
	const struct sdhci_msm_offset *msm_offset =
					msm_host->offset;

	pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__);

	/*
	 * Retuning in HS400 (DDR mode) will fail, just reset the
	 * tuning block and restore the saved tuning phase.
	 */
	ret = msm_init_cm_dll(host);
	if (ret)
		goto out;

	if (!mmc->ios.enhanced_strobe) {
		/* Set the selected phase in delay line hw block */
		ret = msm_config_cm_dll_phase(host,
					      msm_host->saved_tuning_phase);
		if (ret)
			goto out;
		config = readl_relaxed(host->ioaddr +
				msm_offset->core_dll_config);
		config |= CORE_CMD_DAT_TRACK_SEL;
		writel_relaxed(config, host->ioaddr +
				msm_offset->core_dll_config);
	}

	if (msm_host->use_cdclp533)
		ret = sdhci_msm_cdclp533_calibration(host);
	else
		ret = sdhci_msm_cm_dll_sdc4_calibration(host);
out:
	pr_debug("%s: %s: Exit, ret %d\n", mmc_hostname(host->mmc),
		 __func__, ret);
	return ret;
}

static bool sdhci_msm_is_tuning_needed(struct sdhci_host *host)
{
	struct mmc_ios *ios = &host->mmc->ios;

	/*
	 * Tuning is required for SDR104, HS200 and HS400 cards and
	 * if clock frequency is greater than 100MHz in these modes.
	 */
	if (host->clock <= CORE_FREQ_100MHZ ||
	    !(ios->timing == MMC_TIMING_MMC_HS400 ||
	    ios->timing == MMC_TIMING_MMC_HS200 ||
	    ios->timing == MMC_TIMING_UHS_SDR104) ||
	    ios->enhanced_strobe)
		return false;

	return true;
}

static int sdhci_msm_restore_sdr_dll_config(struct sdhci_host *host)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
	int ret;

	/*
	 * SDR DLL comes into picture only for timing modes which needs
	 * tuning.
	 */
	if (!sdhci_msm_is_tuning_needed(host))
		return 0;

	/* Reset the tuning block */
	ret = msm_init_cm_dll(host);
	if (ret)
		return ret;

	/* Restore the tuning block */
	ret = msm_config_cm_dll_phase(host, msm_host->saved_tuning_phase);

	return ret;
}

static void sdhci_msm_set_cdr(struct sdhci_host *host, bool enable)
{
	const struct sdhci_msm_offset *msm_offset = sdhci_priv_msm_offset(host);
	u32 config, oldconfig = readl_relaxed(host->ioaddr +
					      msm_offset->core_dll_config);

	config = oldconfig;
	if (enable) {
		config |= CORE_CDR_EN;
		config &= ~CORE_CDR_EXT_EN;
	} else {
		config &= ~CORE_CDR_EN;
		config |= CORE_CDR_EXT_EN;
	}

	if (config != oldconfig) {
		writel_relaxed(config, host->ioaddr +
			       msm_offset->core_dll_config);
	}
}

static int sdhci_msm_execute_tuning(struct mmc_host *mmc, u32 opcode)
{
	struct sdhci_host *host = mmc_priv(mmc);
	int tuning_seq_cnt = 10;
	u8 phase, tuned_phases[16], tuned_phase_cnt = 0;
	int rc;
	struct mmc_ios ios = host->mmc->ios;
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);

	if (!sdhci_msm_is_tuning_needed(host)) {
		msm_host->use_cdr = false;
		sdhci_msm_set_cdr(host, false);
		return 0;
	}

	/* Clock-Data-Recovery used to dynamically adjust RX sampling point */
	msm_host->use_cdr = true;

	/*
	 * Clear tuning_done flag before tuning to ensure proper
	 * HS400 settings.
	 */
	msm_host->tuning_done = 0;

	/*
	 * For HS400 tuning in HS200 timing requires:
	 * - select MCLK/2 in VENDOR_SPEC
	 * - program MCLK to 400MHz (or nearest supported) in GCC
	 */
	if (host->flags & SDHCI_HS400_TUNING) {
		sdhci_msm_hc_select_mode(host);
		msm_set_clock_rate_for_bus_mode(host, ios.clock);
		host->flags &= ~SDHCI_HS400_TUNING;
	}

retry:
	/* First of all reset the tuning block */
	rc = msm_init_cm_dll(host);
	if (rc)
		return rc;

	phase = 0;
	do {
		/* Set the phase in delay line hw block */
		rc = msm_config_cm_dll_phase(host, phase);
		if (rc)
			return rc;

		rc = mmc_send_tuning(mmc, opcode, NULL);
		if (!rc) {
			/* Tuning is successful at this tuning point */
			tuned_phases[tuned_phase_cnt++] = phase;
			dev_dbg(mmc_dev(mmc), "%s: Found good phase = %d\n",
				 mmc_hostname(mmc), phase);
		}
	} while (++phase < ARRAY_SIZE(tuned_phases));

	if (tuned_phase_cnt) {
		if (tuned_phase_cnt == ARRAY_SIZE(tuned_phases)) {
			/*
			 * All phases valid is _almost_ as bad as no phases
			 * valid.  Probably all phases are not really reliable
			 * but we didn't detect where the unreliable place is.
			 * That means we'll essentially be guessing and hoping
			 * we get a good phase.  Better to try a few times.
			 */
			dev_dbg(mmc_dev(mmc), "%s: All phases valid; try again\n",
				mmc_hostname(mmc));
			if (--tuning_seq_cnt) {
				tuned_phase_cnt = 0;
				goto retry;
			}
		}

		rc = msm_find_most_appropriate_phase(host, tuned_phases,
						     tuned_phase_cnt);
		if (rc < 0)
			return rc;
		else
			phase = rc;

		/*
		 * Finally set the selected phase in delay
		 * line hw block.
		 */
		rc = msm_config_cm_dll_phase(host, phase);
		if (rc)
			return rc;
		msm_host->saved_tuning_phase = phase;
		dev_dbg(mmc_dev(mmc), "%s: Setting the tuning phase to %d\n",
			 mmc_hostname(mmc), phase);
	} else {
		if (--tuning_seq_cnt)
			goto retry;
		/* Tuning failed */
		dev_dbg(mmc_dev(mmc), "%s: No tuning point found\n",
		       mmc_hostname(mmc));
		rc = -EIO;
	}

	if (!rc)
		msm_host->tuning_done = true;
	return rc;
}

/*
 * sdhci_msm_hs400 - Calibrate the DLL for HS400 bus speed mode operation.
 * This needs to be done for both tuning and enhanced_strobe mode.
 * DLL operation is only needed for clock > 100MHz. For clock <= 100MHz
 * fixed feedback clock is used.
 */
static void sdhci_msm_hs400(struct sdhci_host *host, struct mmc_ios *ios)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
	int ret;

	if (host->clock > CORE_FREQ_100MHZ &&
	    (msm_host->tuning_done || ios->enhanced_strobe) &&
	    !msm_host->calibration_done) {
		ret = sdhci_msm_hs400_dll_calibration(host);
		if (!ret)
			msm_host->calibration_done = true;
		else
			pr_err("%s: Failed to calibrate DLL for hs400 mode (%d)\n",
			       mmc_hostname(host->mmc), ret);
	}
}

static void sdhci_msm_set_uhs_signaling(struct sdhci_host *host,
					unsigned int uhs)
{
	struct mmc_host *mmc = host->mmc;
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
	u16 ctrl_2;
	u32 config;
	const struct sdhci_msm_offset *msm_offset =
					msm_host->offset;

	ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
	/* Select Bus Speed Mode for host */
	ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
	switch (uhs) {
	case MMC_TIMING_UHS_SDR12:
		ctrl_2 |= SDHCI_CTRL_UHS_SDR12;
		break;
	case MMC_TIMING_UHS_SDR25:
		ctrl_2 |= SDHCI_CTRL_UHS_SDR25;
		break;
	case MMC_TIMING_UHS_SDR50:
		ctrl_2 |= SDHCI_CTRL_UHS_SDR50;
		break;
	case MMC_TIMING_MMC_HS400:
	case MMC_TIMING_MMC_HS200:
	case MMC_TIMING_UHS_SDR104:
		ctrl_2 |= SDHCI_CTRL_UHS_SDR104;
		break;
	case MMC_TIMING_UHS_DDR50:
	case MMC_TIMING_MMC_DDR52:
		ctrl_2 |= SDHCI_CTRL_UHS_DDR50;
		break;
	}

	/*
	 * When clock frequency is less than 100MHz, the feedback clock must be
	 * provided and DLL must not be used so that tuning can be skipped. To
	 * provide feedback clock, the mode selection can be any value less
	 * than 3'b011 in bits [2:0] of HOST CONTROL2 register.
	 */
	if (host->clock <= CORE_FREQ_100MHZ) {
		if (uhs == MMC_TIMING_MMC_HS400 ||
		    uhs == MMC_TIMING_MMC_HS200 ||
		    uhs == MMC_TIMING_UHS_SDR104)
			ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
		/*
		 * DLL is not required for clock <= 100MHz
		 * Thus, make sure DLL it is disabled when not required
		 */
		config = readl_relaxed(host->ioaddr +
				msm_offset->core_dll_config);
		config |= CORE_DLL_RST;
		writel_relaxed(config, host->ioaddr +
				msm_offset->core_dll_config);

		config = readl_relaxed(host->ioaddr +
				msm_offset->core_dll_config);
		config |= CORE_DLL_PDN;
		writel_relaxed(config, host->ioaddr +
				msm_offset->core_dll_config);

		/*
		 * The DLL needs to be restored and CDCLP533 recalibrated
		 * when the clock frequency is set back to 400MHz.
		 */
		msm_host->calibration_done = false;
	}

	dev_dbg(mmc_dev(mmc), "%s: clock=%u uhs=%u ctrl_2=0x%x\n",
		mmc_hostname(host->mmc), host->clock, uhs, ctrl_2);
	sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);

	if (mmc->ios.timing == MMC_TIMING_MMC_HS400)
		sdhci_msm_hs400(host, &mmc->ios);
}

static int sdhci_msm_set_pincfg(struct sdhci_msm_host *msm_host, bool level)
{
	struct platform_device *pdev = msm_host->pdev;
	int ret;

	if (level)
		ret = pinctrl_pm_select_default_state(&pdev->dev);
	else
		ret = pinctrl_pm_select_sleep_state(&pdev->dev);

	return ret;
}

static void msm_config_vmmc_regulator(struct mmc_host *mmc, bool hpm)
{
	int load;

	if (!hpm)
		load = 0;
	else if (!mmc->card)
		load = max(MMC_VMMC_MAX_LOAD_UA, SD_VMMC_MAX_LOAD_UA);
	else if (mmc_card_mmc(mmc->card))
		load = MMC_VMMC_MAX_LOAD_UA;
	else if (mmc_card_sd(mmc->card))
		load = SD_VMMC_MAX_LOAD_UA;
	else
		return;

	regulator_set_load(mmc->supply.vmmc, load);
}

static void msm_config_vqmmc_regulator(struct mmc_host *mmc, bool hpm)
{
	int load;

	if (!hpm)
		load = 0;
	else if (!mmc->card)
		load = max(MMC_VQMMC_MAX_LOAD_UA, SD_VQMMC_MAX_LOAD_UA);
	else if (mmc_card_sd(mmc->card))
		load = SD_VQMMC_MAX_LOAD_UA;
	else
		return;

	regulator_set_load(mmc->supply.vqmmc, load);
}

static int sdhci_msm_set_vmmc(struct sdhci_msm_host *msm_host,
			      struct mmc_host *mmc, bool hpm)
{
	if (IS_ERR(mmc->supply.vmmc))
		return 0;

	msm_config_vmmc_regulator(mmc, hpm);

	return mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, mmc->ios.vdd);
}

static int msm_toggle_vqmmc(struct sdhci_msm_host *msm_host,
			      struct mmc_host *mmc, bool level)
{
	int ret;
	struct mmc_ios ios;

	if (msm_host->vqmmc_enabled == level)
		return 0;

	msm_config_vqmmc_regulator(mmc, level);

	if (level) {
		/* Set the IO voltage regulator to default voltage level */
		if (msm_host->caps_0 & CORE_3_0V_SUPPORT)
			ios.signal_voltage = MMC_SIGNAL_VOLTAGE_330;
		else if (msm_host->caps_0 & CORE_1_8V_SUPPORT)
			ios.signal_voltage = MMC_SIGNAL_VOLTAGE_180;

		if (msm_host->caps_0 & CORE_VOLT_SUPPORT) {
			ret = mmc_regulator_set_vqmmc(mmc, &ios);
			if (ret < 0) {
				dev_err(mmc_dev(mmc), "%s: vqmmc set volgate failed: %d\n",
					mmc_hostname(mmc), ret);
				goto out;
			}
		}
		ret = regulator_enable(mmc->supply.vqmmc);
	} else {
		ret = regulator_disable(mmc->supply.vqmmc);
	}

	if (ret)
		dev_err(mmc_dev(mmc), "%s: vqmm %sable failed: %d\n",
			mmc_hostname(mmc), level ? "en":"dis", ret);
	else
		msm_host->vqmmc_enabled = level;
out:
	return ret;
}

static int msm_config_vqmmc_mode(struct sdhci_msm_host *msm_host,
			      struct mmc_host *mmc, bool hpm)
{
	int load, ret;

	load = hpm ? MMC_VQMMC_MAX_LOAD_UA : 0;
	ret = regulator_set_load(mmc->supply.vqmmc, load);
	if (ret)
		dev_err(mmc_dev(mmc), "%s: vqmmc set load failed: %d\n",
			mmc_hostname(mmc), ret);
	return ret;
}

static int sdhci_msm_set_vqmmc(struct sdhci_msm_host *msm_host,
			      struct mmc_host *mmc, bool level)
{
	int ret;
	bool always_on;

	if (IS_ERR(mmc->supply.vqmmc) ||
			(mmc->ios.power_mode == MMC_POWER_UNDEFINED))
		return 0;
	/*
	 * For eMMC don't turn off Vqmmc, Instead just configure it in LPM
	 * and HPM modes by setting the corresponding load.
	 *
	 * Till eMMC is initialized (i.e. always_on == 0), just turn on/off
	 * Vqmmc. Vqmmc gets turned off only if init fails and mmc_power_off
	 * gets invoked. Once eMMC is initialized (i.e. always_on == 1),
	 * Vqmmc should remain ON, So just set the load instead of turning it
	 * off/on.
	 */
	always_on = !mmc_card_is_removable(mmc) &&
			mmc->card && mmc_card_mmc(mmc->card);

	if (always_on)
		ret = msm_config_vqmmc_mode(msm_host, mmc, level);
	else
		ret = msm_toggle_vqmmc(msm_host, mmc, level);

	return ret;
}

static inline void sdhci_msm_init_pwr_irq_wait(struct sdhci_msm_host *msm_host)
{
	init_waitqueue_head(&msm_host->pwr_irq_wait);
}

static inline void sdhci_msm_complete_pwr_irq_wait(
		struct sdhci_msm_host *msm_host)
{
	wake_up(&msm_host->pwr_irq_wait);
}

/*
 * sdhci_msm_check_power_status API should be called when registers writes
 * which can toggle sdhci IO bus ON/OFF or change IO lines HIGH/LOW happens.
 * To what state the register writes will change the IO lines should be passed
 * as the argument req_type. This API will check whether the IO line's state
 * is already the expected state and will wait for power irq only if
 * power irq is expected to be triggered based on the current IO line state
 * and expected IO line state.
 */
static void sdhci_msm_check_power_status(struct sdhci_host *host, u32 req_type)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
	bool done = false;
	u32 val = SWITCHABLE_SIGNALING_VOLTAGE;
	const struct sdhci_msm_offset *msm_offset =
					msm_host->offset;

	pr_debug("%s: %s: request %d curr_pwr_state %x curr_io_level %x\n",
			mmc_hostname(host->mmc), __func__, req_type,
			msm_host->curr_pwr_state, msm_host->curr_io_level);

	/*
	 * The power interrupt will not be generated for signal voltage
	 * switches if SWITCHABLE_SIGNALING_VOLTAGE in MCI_GENERICS is not set.
	 * Since sdhci-msm-v5, this bit has been removed and SW must consider
	 * it as always set.
	 */
	if (!msm_host->mci_removed)
		val = msm_host_readl(msm_host, host,
				msm_offset->core_generics);
	if ((req_type & REQ_IO_HIGH || req_type & REQ_IO_LOW) &&
	    !(val & SWITCHABLE_SIGNALING_VOLTAGE)) {
		return;
	}

	/*
	 * The IRQ for request type IO High/LOW will be generated when -
	 * there is a state change in 1.8V enable bit (bit 3) of
	 * SDHCI_HOST_CONTROL2 register. The reset state of that bit is 0
	 * which indicates 3.3V IO voltage. So, when MMC core layer tries
	 * to set it to 3.3V before card detection happens, the
	 * IRQ doesn't get triggered as there is no state change in this bit.
	 * The driver already handles this case by changing the IO voltage
	 * level to high as part of controller power up sequence. Hence, check
	 * for host->pwr to handle a case where IO voltage high request is
	 * issued even before controller power up.
	 */
	if ((req_type & REQ_IO_HIGH) && !host->pwr) {
		pr_debug("%s: do not wait for power IRQ that never comes, req_type: %d\n",
				mmc_hostname(host->mmc), req_type);
		return;
	}
	if ((req_type & msm_host->curr_pwr_state) ||
			(req_type & msm_host->curr_io_level))
		done = true;
	/*
	 * This is needed here to handle cases where register writes will
	 * not change the current bus state or io level of the controller.
	 * In this case, no power irq will be triggerred and we should
	 * not wait.
	 */
	if (!done) {
		if (!wait_event_timeout(msm_host->pwr_irq_wait,
				msm_host->pwr_irq_flag,
				msecs_to_jiffies(MSM_PWR_IRQ_TIMEOUT_MS)))
			dev_warn(&msm_host->pdev->dev,
				 "%s: pwr_irq for req: (%d) timed out\n",
				 mmc_hostname(host->mmc), req_type);
	}
	pr_debug("%s: %s: request %d done\n", mmc_hostname(host->mmc),
			__func__, req_type);
}

static void sdhci_msm_dump_pwr_ctrl_regs(struct sdhci_host *host)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
	const struct sdhci_msm_offset *msm_offset =
					msm_host->offset;

	pr_err("%s: PWRCTL_STATUS: 0x%08x | PWRCTL_MASK: 0x%08x | PWRCTL_CTL: 0x%08x\n",
		mmc_hostname(host->mmc),
		msm_host_readl(msm_host, host, msm_offset->core_pwrctl_status),
		msm_host_readl(msm_host, host, msm_offset->core_pwrctl_mask),
		msm_host_readl(msm_host, host, msm_offset->core_pwrctl_ctl));
}

static void sdhci_msm_handle_pwr_irq(struct sdhci_host *host, int irq)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
	struct mmc_host *mmc = host->mmc;
	u32 irq_status, irq_ack = 0;
	int retry = 10, ret;
	u32 pwr_state = 0, io_level = 0;
	u32 config;
	const struct sdhci_msm_offset *msm_offset = msm_host->offset;

	irq_status = msm_host_readl(msm_host, host,
			msm_offset->core_pwrctl_status);
	irq_status &= INT_MASK;

	msm_host_writel(msm_host, irq_status, host,
			msm_offset->core_pwrctl_clear);

	/*
	 * There is a rare HW scenario where the first clear pulse could be
	 * lost when actual reset and clear/read of status register is
	 * happening at a time. Hence, retry for at least 10 times to make
	 * sure status register is cleared. Otherwise, this will result in
	 * a spurious power IRQ resulting in system instability.
	 */
	while (irq_status & msm_host_readl(msm_host, host,
				msm_offset->core_pwrctl_status)) {
		if (retry == 0) {
			pr_err("%s: Timedout clearing (0x%x) pwrctl status register\n",
					mmc_hostname(host->mmc), irq_status);
			sdhci_msm_dump_pwr_ctrl_regs(host);
			WARN_ON(1);
			break;
		}
		msm_host_writel(msm_host, irq_status, host,
			msm_offset->core_pwrctl_clear);
		retry--;
		udelay(10);
	}

	/* Handle BUS ON/OFF*/
	if (irq_status & CORE_PWRCTL_BUS_ON) {
		pwr_state = REQ_BUS_ON;
		io_level = REQ_IO_HIGH;
	}
	if (irq_status & CORE_PWRCTL_BUS_OFF) {
		pwr_state = REQ_BUS_OFF;
		io_level = REQ_IO_LOW;
	}

	if (pwr_state) {
		ret = sdhci_msm_set_vmmc(msm_host, mmc,
					 pwr_state & REQ_BUS_ON);
		if (!ret)
			ret = sdhci_msm_set_vqmmc(msm_host, mmc,
					pwr_state & REQ_BUS_ON);
		if (!ret)
			ret = sdhci_msm_set_pincfg(msm_host,
					pwr_state & REQ_BUS_ON);
		if (!ret)
			irq_ack |= CORE_PWRCTL_BUS_SUCCESS;
		else
			irq_ack |= CORE_PWRCTL_BUS_FAIL;
	}

	/* Handle IO LOW/HIGH */
	if (irq_status & CORE_PWRCTL_IO_LOW)
		io_level = REQ_IO_LOW;

	if (irq_status & CORE_PWRCTL_IO_HIGH)
		io_level = REQ_IO_HIGH;

	if (io_level)
		irq_ack |= CORE_PWRCTL_IO_SUCCESS;

	if (io_level && !IS_ERR(mmc->supply.vqmmc) && !pwr_state) {
		ret = mmc_regulator_set_vqmmc(mmc, &mmc->ios);
		if (ret < 0) {
			dev_err(mmc_dev(mmc), "%s: IO_level setting failed(%d). signal_voltage: %d, vdd: %d irq_status: 0x%08x\n",
					mmc_hostname(mmc), ret,
					mmc->ios.signal_voltage, mmc->ios.vdd,
					irq_status);
			irq_ack |= CORE_PWRCTL_IO_FAIL;
		}
	}

	/*
	 * The driver has to acknowledge the interrupt, switch voltages and
	 * report back if it succeded or not to this register. The voltage
	 * switches are handled by the sdhci core, so just report success.
	 */
	msm_host_writel(msm_host, irq_ack, host,
			msm_offset->core_pwrctl_ctl);

	/*
	 * If we don't have info regarding the voltage levels supported by
	 * regulators, don't change the IO PAD PWR SWITCH.
	 */
	if (msm_host->caps_0 & CORE_VOLT_SUPPORT) {
		u32 new_config;
		/*
		 * We should unset IO PAD PWR switch only if the register write
		 * can set IO lines high and the regulator also switches to 3 V.
		 * Else, we should keep the IO PAD PWR switch set.
		 * This is applicable to certain targets where eMMC vccq supply
		 * is only 1.8V. In such targets, even during REQ_IO_HIGH, the
		 * IO PAD PWR switch must be kept set to reflect actual
		 * regulator voltage. This way, during initialization of
		 * controllers with only 1.8V, we will set the IO PAD bit
		 * without waiting for a REQ_IO_LOW.
		 */
		config = readl_relaxed(host->ioaddr +
				msm_offset->core_vendor_spec);
		new_config = config;

		if ((io_level & REQ_IO_HIGH) &&
				(msm_host->caps_0 & CORE_3_0V_SUPPORT))
			new_config &= ~CORE_IO_PAD_PWR_SWITCH;
		else if ((io_level & REQ_IO_LOW) ||
				(msm_host->caps_0 & CORE_1_8V_SUPPORT))
			new_config |= CORE_IO_PAD_PWR_SWITCH;

		if (config ^ new_config)
			writel_relaxed(new_config, host->ioaddr +
					msm_offset->core_vendor_spec);
	}

	if (pwr_state)
		msm_host->curr_pwr_state = pwr_state;
	if (io_level)
		msm_host->curr_io_level = io_level;

	dev_dbg(mmc_dev(mmc), "%s: %s: Handled IRQ(%d), irq_status=0x%x, ack=0x%x\n",
		mmc_hostname(msm_host->mmc), __func__, irq, irq_status,
		irq_ack);
}

static irqreturn_t sdhci_msm_pwr_irq(int irq, void *data)
{
	struct sdhci_host *host = (struct sdhci_host *)data;
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);

	sdhci_msm_handle_pwr_irq(host, irq);
	msm_host->pwr_irq_flag = 1;
	sdhci_msm_complete_pwr_irq_wait(msm_host);


	return IRQ_HANDLED;
}

static unsigned int sdhci_msm_get_max_clock(struct sdhci_host *host)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
	struct clk *core_clk = msm_host->bulk_clks[0].clk;

	return clk_round_rate(core_clk, ULONG_MAX);
}

static unsigned int sdhci_msm_get_min_clock(struct sdhci_host *host)
{
	return SDHCI_MSM_MIN_CLOCK;
}

/*
 * __sdhci_msm_set_clock - sdhci_msm clock control.
 *
 * Description:
 * MSM controller does not use internal divider and
 * instead directly control the GCC clock as per
 * HW recommendation.
 **/
static void __sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock)
{
	u16 clk;

	sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);

	if (clock == 0)
		return;

	/*
	 * MSM controller do not use clock divider.
	 * Thus read SDHCI_CLOCK_CONTROL and only enable
	 * clock with no divider value programmed.
	 */
	clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
	sdhci_enable_clk(host, clk);
}

/* sdhci_msm_set_clock - Called with (host->lock) spinlock held. */
static void sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);

	if (!clock) {
		host->mmc->actual_clock = msm_host->clk_rate = 0;
		goto out;
	}

	sdhci_msm_hc_select_mode(host);

	msm_set_clock_rate_for_bus_mode(host, clock);
out:
	__sdhci_msm_set_clock(host, clock);
}

/*****************************************************************************\
 *                                                                           *
 * Inline Crypto Engine (ICE) support                                        *
 *                                                                           *
\*****************************************************************************/

#ifdef CONFIG_MMC_CRYPTO

static const struct blk_crypto_ll_ops sdhci_msm_crypto_ops; /* forward decl */

static int sdhci_msm_ice_init(struct sdhci_msm_host *msm_host,
			      struct cqhci_host *cq_host)
{
	struct mmc_host *mmc = msm_host->mmc;
	struct blk_crypto_profile *profile = &mmc->crypto_profile;
	struct device *dev = mmc_dev(mmc);
	struct qcom_ice *ice;
	union cqhci_crypto_capabilities caps;
	union cqhci_crypto_cap_entry cap;
	int err;
	int i;

	if (!(cqhci_readl(cq_host, CQHCI_CAP) & CQHCI_CAP_CS))
		return 0;

	ice = of_qcom_ice_get(dev);
	if (ice == ERR_PTR(-EOPNOTSUPP)) {
		dev_warn(dev, "Disabling inline encryption support\n");
		ice = NULL;
	}

	if (IS_ERR_OR_NULL(ice))
		return PTR_ERR_OR_ZERO(ice);

	msm_host->ice = ice;

	/* Initialize the blk_crypto_profile */

	caps.reg_val = cpu_to_le32(cqhci_readl(cq_host, CQHCI_CCAP));

	/* The number of keyslots supported is (CFGC+1) */
	err = devm_blk_crypto_profile_init(dev, profile, caps.config_count + 1);
	if (err)
		return err;

	profile->ll_ops = sdhci_msm_crypto_ops;
	profile->max_dun_bytes_supported = 4;
	profile->dev = dev;

	/*
	 * Currently this driver only supports AES-256-XTS.  All known versions
	 * of ICE support it, but to be safe make sure it is really declared in
	 * the crypto capability registers.  The crypto capability registers
	 * also give the supported data unit size(s).
	 */
	for (i = 0; i < caps.num_crypto_cap; i++) {
		cap.reg_val = cpu_to_le32(cqhci_readl(cq_host,
						      CQHCI_CRYPTOCAP +
						      i * sizeof(__le32)));
		if (cap.algorithm_id == CQHCI_CRYPTO_ALG_AES_XTS &&
		    cap.key_size == CQHCI_CRYPTO_KEY_SIZE_256)
			profile->modes_supported[BLK_ENCRYPTION_MODE_AES_256_XTS] |=
				cap.sdus_mask * 512;
	}

	mmc->caps2 |= MMC_CAP2_CRYPTO;
	return 0;
}

static void sdhci_msm_ice_enable(struct sdhci_msm_host *msm_host)
{
	if (msm_host->mmc->caps2 & MMC_CAP2_CRYPTO)
		qcom_ice_enable(msm_host->ice);
}

static __maybe_unused int sdhci_msm_ice_resume(struct sdhci_msm_host *msm_host)
{
	if (msm_host->mmc->caps2 & MMC_CAP2_CRYPTO)
		return qcom_ice_resume(msm_host->ice);

	return 0;
}

static __maybe_unused int sdhci_msm_ice_suspend(struct sdhci_msm_host *msm_host)
{
	if (msm_host->mmc->caps2 & MMC_CAP2_CRYPTO)
		return qcom_ice_suspend(msm_host->ice);

	return 0;
}

static inline struct sdhci_msm_host *
sdhci_msm_host_from_crypto_profile(struct blk_crypto_profile *profile)
{
	struct mmc_host *mmc = mmc_from_crypto_profile(profile);
	struct sdhci_host *host = mmc_priv(mmc);
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);

	return msm_host;
}

/*
 * Program a key into a QC ICE keyslot.  QC ICE requires a QC-specific SCM call
 * for this; it doesn't support the standard way.
 */
static int sdhci_msm_ice_keyslot_program(struct blk_crypto_profile *profile,
					 const struct blk_crypto_key *key,
					 unsigned int slot)
{
	struct sdhci_msm_host *msm_host =
		sdhci_msm_host_from_crypto_profile(profile);

	/* Only AES-256-XTS has been tested so far. */
	if (key->crypto_cfg.crypto_mode != BLK_ENCRYPTION_MODE_AES_256_XTS)
		return -EOPNOTSUPP;

	return qcom_ice_program_key(msm_host->ice,
				    QCOM_ICE_CRYPTO_ALG_AES_XTS,
				    QCOM_ICE_CRYPTO_KEY_SIZE_256,
				    key->raw,
				    key->crypto_cfg.data_unit_size / 512,
				    slot);
}

static int sdhci_msm_ice_keyslot_evict(struct blk_crypto_profile *profile,
				       const struct blk_crypto_key *key,
				       unsigned int slot)
{
	struct sdhci_msm_host *msm_host =
		sdhci_msm_host_from_crypto_profile(profile);

	return qcom_ice_evict_key(msm_host->ice, slot);
}

static const struct blk_crypto_ll_ops sdhci_msm_crypto_ops = {
	.keyslot_program	= sdhci_msm_ice_keyslot_program,
	.keyslot_evict		= sdhci_msm_ice_keyslot_evict,
};

#else /* CONFIG_MMC_CRYPTO */

static inline int sdhci_msm_ice_init(struct sdhci_msm_host *msm_host,
				     struct cqhci_host *cq_host)
{
	return 0;
}

static inline void sdhci_msm_ice_enable(struct sdhci_msm_host *msm_host)
{
}

static inline __maybe_unused int
sdhci_msm_ice_resume(struct sdhci_msm_host *msm_host)
{
	return 0;
}

static inline __maybe_unused int
sdhci_msm_ice_suspend(struct sdhci_msm_host *msm_host)
{
	return 0;
}
#endif /* !CONFIG_MMC_CRYPTO */

/*****************************************************************************\
 *                                                                           *
 * MSM Command Queue Engine (CQE)                                            *
 *                                                                           *
\*****************************************************************************/

static u32 sdhci_msm_cqe_irq(struct sdhci_host *host, u32 intmask)
{
	int cmd_error = 0;
	int data_error = 0;

	if (!sdhci_cqe_irq(host, intmask, &cmd_error, &data_error))
		return intmask;

	cqhci_irq(host->mmc, intmask, cmd_error, data_error);
	return 0;
}

static void sdhci_msm_cqe_enable(struct mmc_host *mmc)
{
	struct sdhci_host *host = mmc_priv(mmc);
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);

	sdhci_cqe_enable(mmc);
	sdhci_msm_ice_enable(msm_host);
}

static void sdhci_msm_cqe_disable(struct mmc_host *mmc, bool recovery)
{
	struct sdhci_host *host = mmc_priv(mmc);
	unsigned long flags;
	u32 ctrl;

	/*
	 * When CQE is halted, the legacy SDHCI path operates only
	 * on 16-byte descriptors in 64bit mode.
	 */
	if (host->flags & SDHCI_USE_64_BIT_DMA)
		host->desc_sz = 16;

	spin_lock_irqsave(&host->lock, flags);

	/*
	 * During CQE command transfers, command complete bit gets latched.
	 * So s/w should clear command complete interrupt status when CQE is
	 * either halted or disabled. Otherwise unexpected SDCHI legacy
	 * interrupt gets triggered when CQE is halted/disabled.
	 */
	ctrl = sdhci_readl(host, SDHCI_INT_ENABLE);
	ctrl |= SDHCI_INT_RESPONSE;
	sdhci_writel(host,  ctrl, SDHCI_INT_ENABLE);
	sdhci_writel(host, SDHCI_INT_RESPONSE, SDHCI_INT_STATUS);

	spin_unlock_irqrestore(&host->lock, flags);

	sdhci_cqe_disable(mmc, recovery);
}

static void sdhci_msm_set_timeout(struct sdhci_host *host, struct mmc_command *cmd)
{
	u32 count, start = 15;

	__sdhci_set_timeout(host, cmd);
	count = sdhci_readb(host, SDHCI_TIMEOUT_CONTROL);
	/*
	 * Update software timeout value if its value is less than hardware data
	 * timeout value. Qcom SoC hardware data timeout value was calculated
	 * using 4 * MCLK * 2^(count + 13). where MCLK = 1 / host->clock.
	 */
	if (cmd && cmd->data && host->clock > 400000 &&
	    host->clock <= 50000000 &&
	    ((1 << (count + start)) > (10 * host->clock)))
		host->data_timeout = 22LL * NSEC_PER_SEC;
}

static const struct cqhci_host_ops sdhci_msm_cqhci_ops = {
	.enable		= sdhci_msm_cqe_enable,
	.disable	= sdhci_msm_cqe_disable,
#ifdef CONFIG_MMC_CRYPTO
	.uses_custom_crypto_profile = true,
#endif
};

static int sdhci_msm_cqe_add_host(struct sdhci_host *host,
				struct platform_device *pdev)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
	struct cqhci_host *cq_host;
	bool dma64;
	u32 cqcfg;
	int ret;

	/*
	 * When CQE is halted, SDHC operates only on 16byte ADMA descriptors.
	 * So ensure ADMA table is allocated for 16byte descriptors.
	 */
	if (host->caps & SDHCI_CAN_64BIT)
		host->alloc_desc_sz = 16;

	ret = sdhci_setup_host(host);
	if (ret)
		return ret;

	cq_host = cqhci_pltfm_init(pdev);
	if (IS_ERR(cq_host)) {
		ret = PTR_ERR(cq_host);
		dev_err(&pdev->dev, "cqhci-pltfm init: failed: %d\n", ret);
		goto cleanup;
	}

	msm_host->mmc->caps2 |= MMC_CAP2_CQE | MMC_CAP2_CQE_DCMD;
	cq_host->ops = &sdhci_msm_cqhci_ops;

	dma64 = host->flags & SDHCI_USE_64_BIT_DMA;

	ret = sdhci_msm_ice_init(msm_host, cq_host);
	if (ret)
		goto cleanup;

	ret = cqhci_init(cq_host, host->mmc, dma64);
	if (ret) {
		dev_err(&pdev->dev, "%s: CQE init: failed (%d)\n",
				mmc_hostname(host->mmc), ret);
		goto cleanup;
	}

	/* Disable cqe reset due to cqe enable signal */
	cqcfg = cqhci_readl(cq_host, CQHCI_VENDOR_CFG1);
	cqcfg |= CQHCI_VENDOR_DIS_RST_ON_CQ_EN;
	cqhci_writel(cq_host, cqcfg, CQHCI_VENDOR_CFG1);

	/*
	 * SDHC expects 12byte ADMA descriptors till CQE is enabled.
	 * So limit desc_sz to 12 so that the data commands that are sent
	 * during card initialization (before CQE gets enabled) would
	 * get executed without any issues.
	 */
	if (host->flags & SDHCI_USE_64_BIT_DMA)
		host->desc_sz = 12;

	ret = __sdhci_add_host(host);
	if (ret)
		goto cleanup;

	dev_info(&pdev->dev, "%s: CQE init: success\n",
			mmc_hostname(host->mmc));
	return ret;

cleanup:
	sdhci_cleanup_host(host);
	return ret;
}

/*
 * Platform specific register write functions. This is so that, if any
 * register write needs to be followed up by platform specific actions,
 * they can be added here. These functions can go to sleep when writes
 * to certain registers are done.
 * These functions are relying on sdhci_set_ios not using spinlock.
 */
static int __sdhci_msm_check_write(struct sdhci_host *host, u16 val, int reg)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
	u32 req_type = 0;

	switch (reg) {
	case SDHCI_HOST_CONTROL2:
		req_type = (val & SDHCI_CTRL_VDD_180) ? REQ_IO_LOW :
			REQ_IO_HIGH;
		break;
	case SDHCI_SOFTWARE_RESET:
		if (host->pwr && (val & SDHCI_RESET_ALL))
			req_type = REQ_BUS_OFF;
		break;
	case SDHCI_POWER_CONTROL:
		req_type = !val ? REQ_BUS_OFF : REQ_BUS_ON;
		break;
	case SDHCI_TRANSFER_MODE:
		msm_host->transfer_mode = val;
		break;
	case SDHCI_COMMAND:
		if (!msm_host->use_cdr)
			break;
		if ((msm_host->transfer_mode & SDHCI_TRNS_READ) &&
		    !mmc_op_tuning(SDHCI_GET_CMD(val)))
			sdhci_msm_set_cdr(host, true);
		else
			sdhci_msm_set_cdr(host, false);
		break;
	}

	if (req_type) {
		msm_host->pwr_irq_flag = 0;
		/*
		 * Since this register write may trigger a power irq, ensure
		 * all previous register writes are complete by this point.
		 */
		mb();
	}
	return req_type;
}

/* This function may sleep*/
static void sdhci_msm_writew(struct sdhci_host *host, u16 val, int reg)
{
	u32 req_type = 0;

	req_type = __sdhci_msm_check_write(host, val, reg);
	writew_relaxed(val, host->ioaddr + reg);

	if (req_type)
		sdhci_msm_check_power_status(host, req_type);
}

/* This function may sleep*/
static void sdhci_msm_writeb(struct sdhci_host *host, u8 val, int reg)
{
	u32 req_type = 0;

	req_type = __sdhci_msm_check_write(host, val, reg);

	writeb_relaxed(val, host->ioaddr + reg);

	if (req_type)
		sdhci_msm_check_power_status(host, req_type);
}

static void sdhci_msm_set_regulator_caps(struct sdhci_msm_host *msm_host)
{
	struct mmc_host *mmc = msm_host->mmc;
	struct regulator *supply = mmc->supply.vqmmc;
	u32 caps = 0, config;
	struct sdhci_host *host = mmc_priv(mmc);
	const struct sdhci_msm_offset *msm_offset = msm_host->offset;

	if (!IS_ERR(mmc->supply.vqmmc)) {
		if (regulator_is_supported_voltage(supply, 1700000, 1950000))
			caps |= CORE_1_8V_SUPPORT;
		if (regulator_is_supported_voltage(supply, 2700000, 3600000))
			caps |= CORE_3_0V_SUPPORT;

		if (!caps)
			pr_warn("%s: 1.8/3V not supported for vqmmc\n",
					mmc_hostname(mmc));
	}

	if (caps) {
		/*
		 * Set the PAD_PWR_SWITCH_EN bit so that the PAD_PWR_SWITCH
		 * bit can be used as required later on.
		 */
		u32 io_level = msm_host->curr_io_level;

		config = readl_relaxed(host->ioaddr +
				msm_offset->core_vendor_spec);
		config |= CORE_IO_PAD_PWR_SWITCH_EN;

		if ((io_level & REQ_IO_HIGH) && (caps &	CORE_3_0V_SUPPORT))
			config &= ~CORE_IO_PAD_PWR_SWITCH;
		else if ((io_level & REQ_IO_LOW) || (caps & CORE_1_8V_SUPPORT))
			config |= CORE_IO_PAD_PWR_SWITCH;

		writel_relaxed(config,
				host->ioaddr + msm_offset->core_vendor_spec);
	}
	msm_host->caps_0 |= caps;
	pr_debug("%s: supported caps: 0x%08x\n", mmc_hostname(mmc), caps);
}

static int sdhci_msm_register_vreg(struct sdhci_msm_host *msm_host)
{
	int ret;

	ret = mmc_regulator_get_supply(msm_host->mmc);
	if (ret)
		return ret;

	sdhci_msm_set_regulator_caps(msm_host);

	return 0;
}

static int sdhci_msm_start_signal_voltage_switch(struct mmc_host *mmc,
				      struct mmc_ios *ios)
{
	struct sdhci_host *host = mmc_priv(mmc);
	u16 ctrl, status;

	/*
	 * Signal Voltage Switching is only applicable for Host Controllers
	 * v3.00 and above.
	 */
	if (host->version < SDHCI_SPEC_300)
		return 0;

	ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);

	switch (ios->signal_voltage) {
	case MMC_SIGNAL_VOLTAGE_330:
		if (!(host->flags & SDHCI_SIGNALING_330))
			return -EINVAL;

		/* Set 1.8V Signal Enable in the Host Control2 register to 0 */
		ctrl &= ~SDHCI_CTRL_VDD_180;
		break;
	case MMC_SIGNAL_VOLTAGE_180:
		if (!(host->flags & SDHCI_SIGNALING_180))
			return -EINVAL;

		/* Enable 1.8V Signal Enable in the Host Control2 register */
		ctrl |= SDHCI_CTRL_VDD_180;
		break;

	default:
		return -EINVAL;
	}

	sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);

	/* Wait for 5ms */
	usleep_range(5000, 5500);

	/* regulator output should be stable within 5 ms */
	status = ctrl & SDHCI_CTRL_VDD_180;
	ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
	if ((ctrl & SDHCI_CTRL_VDD_180) == status)
		return 0;

	dev_warn(mmc_dev(mmc), "%s: Regulator output did not became stable\n",
		mmc_hostname(mmc));

	return -EAGAIN;
}

#define DRIVER_NAME "sdhci_msm"
#define SDHCI_MSM_DUMP(f, x...) \
	pr_err("%s: " DRIVER_NAME ": " f, mmc_hostname(host->mmc), ## x)

static void sdhci_msm_dump_vendor_regs(struct sdhci_host *host)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
	const struct sdhci_msm_offset *msm_offset = msm_host->offset;

	SDHCI_MSM_DUMP("----------- VENDOR REGISTER DUMP -----------\n");

	SDHCI_MSM_DUMP(
			"DLL sts: 0x%08x | DLL cfg:  0x%08x | DLL cfg2: 0x%08x\n",
		readl_relaxed(host->ioaddr + msm_offset->core_dll_status),
		readl_relaxed(host->ioaddr + msm_offset->core_dll_config),
		readl_relaxed(host->ioaddr + msm_offset->core_dll_config_2));
	SDHCI_MSM_DUMP(
			"DLL cfg3: 0x%08x | DLL usr ctl:  0x%08x | DDR cfg: 0x%08x\n",
		readl_relaxed(host->ioaddr + msm_offset->core_dll_config_3),
		readl_relaxed(host->ioaddr + msm_offset->core_dll_usr_ctl),
		readl_relaxed(host->ioaddr + msm_offset->core_ddr_config));
	SDHCI_MSM_DUMP(
			"Vndr func: 0x%08x | Vndr func2 : 0x%08x Vndr func3: 0x%08x\n",
		readl_relaxed(host->ioaddr + msm_offset->core_vendor_spec),
		readl_relaxed(host->ioaddr +
			msm_offset->core_vendor_spec_func2),
		readl_relaxed(host->ioaddr + msm_offset->core_vendor_spec3));
}

static const struct sdhci_msm_variant_ops mci_var_ops = {
	.msm_readl_relaxed = sdhci_msm_mci_variant_readl_relaxed,
	.msm_writel_relaxed = sdhci_msm_mci_variant_writel_relaxed,
};

static const struct sdhci_msm_variant_ops v5_var_ops = {
	.msm_readl_relaxed = sdhci_msm_v5_variant_readl_relaxed,
	.msm_writel_relaxed = sdhci_msm_v5_variant_writel_relaxed,
};

static const struct sdhci_msm_variant_info sdhci_msm_mci_var = {
	.var_ops = &mci_var_ops,
	.offset = &sdhci_msm_mci_offset,
};

static const struct sdhci_msm_variant_info sdhci_msm_v5_var = {
	.mci_removed = true,
	.var_ops = &v5_var_ops,
	.offset = &sdhci_msm_v5_offset,
};

static const struct sdhci_msm_variant_info sdm845_sdhci_var = {
	.mci_removed = true,
	.restore_dll_config = true,
	.var_ops = &v5_var_ops,
	.offset = &sdhci_msm_v5_offset,
};

static const struct of_device_id sdhci_msm_dt_match[] = {
	/*
	 * Do not add new variants to the driver which are compatible with
	 * generic ones, unless they need customization.
	 */
	{.compatible = "qcom,sdhci-msm-v4", .data = &sdhci_msm_mci_var},
	{.compatible = "qcom,sdhci-msm-v5", .data = &sdhci_msm_v5_var},
	{.compatible = "qcom,sdm670-sdhci", .data = &sdm845_sdhci_var},
	{.compatible = "qcom,sdm845-sdhci", .data = &sdm845_sdhci_var},
	{.compatible = "qcom,sc7180-sdhci", .data = &sdm845_sdhci_var},
	{},
};

MODULE_DEVICE_TABLE(of, sdhci_msm_dt_match);

static const struct sdhci_ops sdhci_msm_ops = {
	.reset = sdhci_and_cqhci_reset,
	.set_clock = sdhci_msm_set_clock,
	.get_min_clock = sdhci_msm_get_min_clock,
	.get_max_clock = sdhci_msm_get_max_clock,
	.set_bus_width = sdhci_set_bus_width,
	.set_uhs_signaling = sdhci_msm_set_uhs_signaling,
	.write_w = sdhci_msm_writew,
	.write_b = sdhci_msm_writeb,
	.irq	= sdhci_msm_cqe_irq,
	.dump_vendor_regs = sdhci_msm_dump_vendor_regs,
	.set_power = sdhci_set_power_noreg,
	.set_timeout = sdhci_msm_set_timeout,
};

static const struct sdhci_pltfm_data sdhci_msm_pdata = {
	.quirks = SDHCI_QUIRK_BROKEN_CARD_DETECTION |
		  SDHCI_QUIRK_SINGLE_POWER_WRITE |
		  SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN |
		  SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12,

	.quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN,
	.ops = &sdhci_msm_ops,
};

static inline void sdhci_msm_get_of_property(struct platform_device *pdev,
		struct sdhci_host *host)
{
	struct device_node *node = pdev->dev.of_node;
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);

	if (of_property_read_u32(node, "qcom,ddr-config",
				&msm_host->ddr_config))
		msm_host->ddr_config = DDR_CONFIG_POR_VAL;

	of_property_read_u32(node, "qcom,dll-config", &msm_host->dll_config);

	if (of_device_is_compatible(node, "qcom,msm8916-sdhci"))
		host->quirks2 |= SDHCI_QUIRK2_BROKEN_64_BIT_DMA;
}

static int sdhci_msm_gcc_reset(struct device *dev, struct sdhci_host *host)
{
	struct reset_control *reset;
	int ret = 0;

	reset = reset_control_get_optional_exclusive(dev, NULL);
	if (IS_ERR(reset))
		return dev_err_probe(dev, PTR_ERR(reset),
				"unable to acquire core_reset\n");

	if (!reset)
		return ret;

	ret = reset_control_assert(reset);
	if (ret) {
		reset_control_put(reset);
		return dev_err_probe(dev, ret, "core_reset assert failed\n");
	}

	/*
	 * The hardware requirement for delay between assert/deassert
	 * is at least 3-4 sleep clock (32.7KHz) cycles, which comes to
	 * ~125us (4/32768). To be on the safe side add 200us delay.
	 */
	usleep_range(200, 210);

	ret = reset_control_deassert(reset);
	if (ret) {
		reset_control_put(reset);
		return dev_err_probe(dev, ret, "core_reset deassert failed\n");
	}

	usleep_range(200, 210);
	reset_control_put(reset);

	return ret;
}

static int sdhci_msm_probe(struct platform_device *pdev)
{
	struct sdhci_host *host;
	struct sdhci_pltfm_host *pltfm_host;
	struct sdhci_msm_host *msm_host;
	struct clk *clk;
	int ret;
	u16 host_version, core_minor;
	u32 core_version, config;
	u8 core_major;
	const struct sdhci_msm_offset *msm_offset;
	const struct sdhci_msm_variant_info *var_info;
	struct device_node *node = pdev->dev.of_node;

	host = sdhci_pltfm_init(pdev, &sdhci_msm_pdata, sizeof(*msm_host));
	if (IS_ERR(host))
		return PTR_ERR(host);

	host->sdma_boundary = 0;
	pltfm_host = sdhci_priv(host);
	msm_host = sdhci_pltfm_priv(pltfm_host);
	msm_host->mmc = host->mmc;
	msm_host->pdev = pdev;

	ret = mmc_of_parse(host->mmc);
	if (ret)
		goto pltfm_free;

	/*
	 * Based on the compatible string, load the required msm host info from
	 * the data associated with the version info.
	 */
	var_info = of_device_get_match_data(&pdev->dev);

	msm_host->mci_removed = var_info->mci_removed;
	msm_host->restore_dll_config = var_info->restore_dll_config;
	msm_host->var_ops = var_info->var_ops;
	msm_host->offset = var_info->offset;

	msm_offset = msm_host->offset;

	sdhci_get_of_property(pdev);
	sdhci_msm_get_of_property(pdev, host);

	msm_host->saved_tuning_phase = INVALID_TUNING_PHASE;

	ret = sdhci_msm_gcc_reset(&pdev->dev, host);
	if (ret)
		goto pltfm_free;

	/* Setup SDCC bus voter clock. */
	msm_host->bus_clk = devm_clk_get(&pdev->dev, "bus");
	if (!IS_ERR(msm_host->bus_clk)) {
		/* Vote for max. clk rate for max. performance */
		ret = clk_set_rate(msm_host->bus_clk, INT_MAX);
		if (ret)
			goto pltfm_free;
		ret = clk_prepare_enable(msm_host->bus_clk);
		if (ret)
			goto pltfm_free;
	}

	/* Setup main peripheral bus clock */
	clk = devm_clk_get(&pdev->dev, "iface");
	if (IS_ERR(clk)) {
		ret = PTR_ERR(clk);
		dev_err(&pdev->dev, "Peripheral clk setup failed (%d)\n", ret);
		goto bus_clk_disable;
	}
	msm_host->bulk_clks[1].clk = clk;

	/* Setup SDC MMC clock */
	clk = devm_clk_get(&pdev->dev, "core");
	if (IS_ERR(clk)) {
		ret = PTR_ERR(clk);
		dev_err(&pdev->dev, "SDC MMC clk setup failed (%d)\n", ret);
		goto bus_clk_disable;
	}
	msm_host->bulk_clks[0].clk = clk;

	 /* Check for optional interconnect paths */
	ret = dev_pm_opp_of_find_icc_paths(&pdev->dev, NULL);
	if (ret)
		goto bus_clk_disable;

	ret = devm_pm_opp_set_clkname(&pdev->dev, "core");
	if (ret)
		goto bus_clk_disable;

	/* OPP table is optional */
	ret = devm_pm_opp_of_add_table(&pdev->dev);
	if (ret && ret != -ENODEV) {
		dev_err(&pdev->dev, "Invalid OPP table in Device tree\n");
		goto bus_clk_disable;
	}

	/* Vote for maximum clock rate for maximum performance */
	ret = dev_pm_opp_set_rate(&pdev->dev, INT_MAX);
	if (ret)
		dev_warn(&pdev->dev, "core clock boost failed\n");

	clk = devm_clk_get(&pdev->dev, "cal");
	if (IS_ERR(clk))
		clk = NULL;
	msm_host->bulk_clks[2].clk = clk;

	clk = devm_clk_get(&pdev->dev, "sleep");
	if (IS_ERR(clk))
		clk = NULL;
	msm_host->bulk_clks[3].clk = clk;

	ret = clk_bulk_prepare_enable(ARRAY_SIZE(msm_host->bulk_clks),
				      msm_host->bulk_clks);
	if (ret)
		goto bus_clk_disable;

	/*
	 * xo clock is needed for FLL feature of cm_dll.
	 * In case if xo clock is not mentioned in DT, warn and proceed.
	 */
	msm_host->xo_clk = devm_clk_get(&pdev->dev, "xo");
	if (IS_ERR(msm_host->xo_clk)) {
		ret = PTR_ERR(msm_host->xo_clk);
		dev_warn(&pdev->dev, "TCXO clk not present (%d)\n", ret);
	}

	if (!msm_host->mci_removed) {
		msm_host->core_mem = devm_platform_ioremap_resource(pdev, 1);
		if (IS_ERR(msm_host->core_mem)) {
			ret = PTR_ERR(msm_host->core_mem);
			goto clk_disable;
		}
	}

	/* Reset the vendor spec register to power on reset state */
	writel_relaxed(CORE_VENDOR_SPEC_POR_VAL,
			host->ioaddr + msm_offset->core_vendor_spec);

	if (!msm_host->mci_removed) {
		/* Set HC_MODE_EN bit in HC_MODE register */
		msm_host_writel(msm_host, HC_MODE_EN, host,
				msm_offset->core_hc_mode);
		config = msm_host_readl(msm_host, host,
				msm_offset->core_hc_mode);
		config |= FF_CLK_SW_RST_DIS;
		msm_host_writel(msm_host, config, host,
				msm_offset->core_hc_mode);
	}

	host_version = readw_relaxed((host->ioaddr + SDHCI_HOST_VERSION));
	dev_dbg(&pdev->dev, "Host Version: 0x%x Vendor Version 0x%x\n",
		host_version, ((host_version & SDHCI_VENDOR_VER_MASK) >>
			       SDHCI_VENDOR_VER_SHIFT));

	core_version = msm_host_readl(msm_host, host,
			msm_offset->core_mci_version);
	core_major = (core_version & CORE_VERSION_MAJOR_MASK) >>
		      CORE_VERSION_MAJOR_SHIFT;
	core_minor = core_version & CORE_VERSION_MINOR_MASK;
	dev_dbg(&pdev->dev, "MCI Version: 0x%08x, major: 0x%04x, minor: 0x%02x\n",
		core_version, core_major, core_minor);

	if (core_major == 1 && core_minor >= 0x42)
		msm_host->use_14lpp_dll_reset = true;

	/*
	 * SDCC 5 controller with major version 1, minor version 0x34 and later
	 * with HS 400 mode support will use CM DLL instead of CDC LP 533 DLL.
	 */
	if (core_major == 1 && core_minor < 0x34)
		msm_host->use_cdclp533 = true;

	/*
	 * Support for some capabilities is not advertised by newer
	 * controller versions and must be explicitly enabled.
	 */
	if (core_major >= 1 && core_minor != 0x11 && core_minor != 0x12) {
		config = readl_relaxed(host->ioaddr + SDHCI_CAPABILITIES);
		config |= SDHCI_CAN_VDD_300 | SDHCI_CAN_DO_8BIT;
		writel_relaxed(config, host->ioaddr +
				msm_offset->core_vendor_spec_capabilities0);
	}

	if (core_major == 1 && core_minor >= 0x49)
		msm_host->updated_ddr_cfg = true;

	if (core_major == 1 && core_minor >= 0x71)
		msm_host->uses_tassadar_dll = true;

	ret = sdhci_msm_register_vreg(msm_host);
	if (ret)
		goto clk_disable;

	/*
	 * Power on reset state may trigger power irq if previous status of
	 * PWRCTL was either BUS_ON or IO_HIGH_V. So before enabling pwr irq
	 * interrupt in GIC, any pending power irq interrupt should be
	 * acknowledged. Otherwise power irq interrupt handler would be
	 * fired prematurely.
	 */
	sdhci_msm_handle_pwr_irq(host, 0);

	/*
	 * Ensure that above writes are propagated before interrupt enablement
	 * in GIC.
	 */
	mb();

	/* Setup IRQ for handling power/voltage tasks with PMIC */
	msm_host->pwr_irq = platform_get_irq_byname(pdev, "pwr_irq");
	if (msm_host->pwr_irq < 0) {
		ret = msm_host->pwr_irq;
		goto clk_disable;
	}

	sdhci_msm_init_pwr_irq_wait(msm_host);
	/* Enable pwr irq interrupts */
	msm_host_writel(msm_host, INT_MASK, host,
		msm_offset->core_pwrctl_mask);

	ret = devm_request_threaded_irq(&pdev->dev, msm_host->pwr_irq, NULL,
					sdhci_msm_pwr_irq, IRQF_ONESHOT,
					dev_name(&pdev->dev), host);
	if (ret) {
		dev_err(&pdev->dev, "Request IRQ failed (%d)\n", ret);
		goto clk_disable;
	}

	msm_host->mmc->caps |= MMC_CAP_WAIT_WHILE_BUSY | MMC_CAP_NEED_RSP_BUSY;

	/* Set the timeout value to max possible */
	host->max_timeout_count = 0xF;

	pm_runtime_get_noresume(&pdev->dev);
	pm_runtime_set_active(&pdev->dev);
	pm_runtime_enable(&pdev->dev);
	pm_runtime_set_autosuspend_delay(&pdev->dev,
					 MSM_MMC_AUTOSUSPEND_DELAY_MS);
	pm_runtime_use_autosuspend(&pdev->dev);

	host->mmc_host_ops.start_signal_voltage_switch =
		sdhci_msm_start_signal_voltage_switch;
	host->mmc_host_ops.execute_tuning = sdhci_msm_execute_tuning;
	if (of_property_read_bool(node, "supports-cqe"))
		ret = sdhci_msm_cqe_add_host(host, pdev);
	else
		ret = sdhci_add_host(host);
	if (ret)
		goto pm_runtime_disable;

	pm_runtime_mark_last_busy(&pdev->dev);
	pm_runtime_put_autosuspend(&pdev->dev);

	return 0;

pm_runtime_disable:
	pm_runtime_disable(&pdev->dev);
	pm_runtime_set_suspended(&pdev->dev);
	pm_runtime_put_noidle(&pdev->dev);
clk_disable:
	clk_bulk_disable_unprepare(ARRAY_SIZE(msm_host->bulk_clks),
				   msm_host->bulk_clks);
bus_clk_disable:
	if (!IS_ERR(msm_host->bus_clk))
		clk_disable_unprepare(msm_host->bus_clk);
pltfm_free:
	sdhci_pltfm_free(pdev);
	return ret;
}

static void sdhci_msm_remove(struct platform_device *pdev)
{
	struct sdhci_host *host = platform_get_drvdata(pdev);
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
	int dead = (readl_relaxed(host->ioaddr + SDHCI_INT_STATUS) ==
		    0xffffffff);

	sdhci_remove_host(host, dead);

	pm_runtime_get_sync(&pdev->dev);
	pm_runtime_disable(&pdev->dev);
	pm_runtime_put_noidle(&pdev->dev);

	clk_bulk_disable_unprepare(ARRAY_SIZE(msm_host->bulk_clks),
				   msm_host->bulk_clks);
	if (!IS_ERR(msm_host->bus_clk))
		clk_disable_unprepare(msm_host->bus_clk);
	sdhci_pltfm_free(pdev);
}

static __maybe_unused int sdhci_msm_runtime_suspend(struct device *dev)
{
	struct sdhci_host *host = dev_get_drvdata(dev);
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
	unsigned long flags;

	spin_lock_irqsave(&host->lock, flags);
	host->runtime_suspended = true;
	spin_unlock_irqrestore(&host->lock, flags);

	/* Drop the performance vote */
	dev_pm_opp_set_rate(dev, 0);
	clk_bulk_disable_unprepare(ARRAY_SIZE(msm_host->bulk_clks),
				   msm_host->bulk_clks);

	return sdhci_msm_ice_suspend(msm_host);
}

static __maybe_unused int sdhci_msm_runtime_resume(struct device *dev)
{
	struct sdhci_host *host = dev_get_drvdata(dev);
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
	unsigned long flags;
	int ret;

	ret = clk_bulk_prepare_enable(ARRAY_SIZE(msm_host->bulk_clks),
				       msm_host->bulk_clks);
	if (ret)
		return ret;
	/*
	 * Whenever core-clock is gated dynamically, it's needed to
	 * restore the SDR DLL settings when the clock is ungated.
	 */
	if (msm_host->restore_dll_config && msm_host->clk_rate) {
		ret = sdhci_msm_restore_sdr_dll_config(host);
		if (ret)
			return ret;
	}

	dev_pm_opp_set_rate(dev, msm_host->clk_rate);

	ret = sdhci_msm_ice_resume(msm_host);
	if (ret)
		return ret;

	spin_lock_irqsave(&host->lock, flags);
	host->runtime_suspended = false;
	spin_unlock_irqrestore(&host->lock, flags);

	return ret;
}

static const struct dev_pm_ops sdhci_msm_pm_ops = {
	SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
				pm_runtime_force_resume)
	SET_RUNTIME_PM_OPS(sdhci_msm_runtime_suspend,
			   sdhci_msm_runtime_resume,
			   NULL)
};

static struct platform_driver sdhci_msm_driver = {
	.probe = sdhci_msm_probe,
	.remove = sdhci_msm_remove,
	.driver = {
		   .name = "sdhci_msm",
		   .of_match_table = sdhci_msm_dt_match,
		   .pm = &sdhci_msm_pm_ops,
		   .probe_type = PROBE_PREFER_ASYNCHRONOUS,
	},
};

module_platform_driver(sdhci_msm_driver);

MODULE_DESCRIPTION("Qualcomm Secure Digital Host Controller Interface driver");
MODULE_LICENSE("GPL v2");