1 /* 2 * drivers/mmc/host/omap_hsmmc.c 3 * 4 * Driver for OMAP2430/3430 MMC controller. 5 * 6 * Copyright (C) 2007 Texas Instruments. 7 * 8 * Authors: 9 * Syed Mohammed Khasim <x0khasim@ti.com> 10 * Madhusudhan <madhu.cr@ti.com> 11 * Mohit Jalori <mjalori@ti.com> 12 * 13 * This file is licensed under the terms of the GNU General Public License 14 * version 2. This program is licensed "as is" without any warranty of any 15 * kind, whether express or implied. 16 */ 17 18 #include <linux/module.h> 19 #include <linux/init.h> 20 #include <linux/kernel.h> 21 #include <linux/debugfs.h> 22 #include <linux/dmaengine.h> 23 #include <linux/seq_file.h> 24 #include <linux/sizes.h> 25 #include <linux/interrupt.h> 26 #include <linux/delay.h> 27 #include <linux/dma-mapping.h> 28 #include <linux/platform_device.h> 29 #include <linux/timer.h> 30 #include <linux/clk.h> 31 #include <linux/of.h> 32 #include <linux/of_irq.h> 33 #include <linux/of_device.h> 34 #include <linux/mmc/host.h> 35 #include <linux/mmc/core.h> 36 #include <linux/mmc/mmc.h> 37 #include <linux/mmc/slot-gpio.h> 38 #include <linux/io.h> 39 #include <linux/irq.h> 40 #include <linux/regulator/consumer.h> 41 #include <linux/pinctrl/consumer.h> 42 #include <linux/pm_runtime.h> 43 #include <linux/pm_wakeirq.h> 44 #include <linux/platform_data/hsmmc-omap.h> 45 46 /* OMAP HSMMC Host Controller Registers */ 47 #define OMAP_HSMMC_SYSSTATUS 0x0014 48 #define OMAP_HSMMC_CON 0x002C 49 #define OMAP_HSMMC_SDMASA 0x0100 50 #define OMAP_HSMMC_BLK 0x0104 51 #define OMAP_HSMMC_ARG 0x0108 52 #define OMAP_HSMMC_CMD 0x010C 53 #define OMAP_HSMMC_RSP10 0x0110 54 #define OMAP_HSMMC_RSP32 0x0114 55 #define OMAP_HSMMC_RSP54 0x0118 56 #define OMAP_HSMMC_RSP76 0x011C 57 #define OMAP_HSMMC_DATA 0x0120 58 #define OMAP_HSMMC_PSTATE 0x0124 59 #define OMAP_HSMMC_HCTL 0x0128 60 #define OMAP_HSMMC_SYSCTL 0x012C 61 #define OMAP_HSMMC_STAT 0x0130 62 #define OMAP_HSMMC_IE 0x0134 63 #define OMAP_HSMMC_ISE 0x0138 64 #define OMAP_HSMMC_AC12 0x013C 65 #define OMAP_HSMMC_CAPA 0x0140 66 67 #define VS18 (1 << 26) 68 #define VS30 (1 << 25) 69 #define HSS (1 << 21) 70 #define SDVS18 (0x5 << 9) 71 #define SDVS30 (0x6 << 9) 72 #define SDVS33 (0x7 << 9) 73 #define SDVS_MASK 0x00000E00 74 #define SDVSCLR 0xFFFFF1FF 75 #define SDVSDET 0x00000400 76 #define AUTOIDLE 0x1 77 #define SDBP (1 << 8) 78 #define DTO 0xe 79 #define ICE 0x1 80 #define ICS 0x2 81 #define CEN (1 << 2) 82 #define CLKD_MAX 0x3FF /* max clock divisor: 1023 */ 83 #define CLKD_MASK 0x0000FFC0 84 #define CLKD_SHIFT 6 85 #define DTO_MASK 0x000F0000 86 #define DTO_SHIFT 16 87 #define INIT_STREAM (1 << 1) 88 #define ACEN_ACMD23 (2 << 2) 89 #define DP_SELECT (1 << 21) 90 #define DDIR (1 << 4) 91 #define DMAE 0x1 92 #define MSBS (1 << 5) 93 #define BCE (1 << 1) 94 #define FOUR_BIT (1 << 1) 95 #define HSPE (1 << 2) 96 #define IWE (1 << 24) 97 #define DDR (1 << 19) 98 #define CLKEXTFREE (1 << 16) 99 #define CTPL (1 << 11) 100 #define DW8 (1 << 5) 101 #define OD 0x1 102 #define STAT_CLEAR 0xFFFFFFFF 103 #define INIT_STREAM_CMD 0x00000000 104 #define DUAL_VOLT_OCR_BIT 7 105 #define SRC (1 << 25) 106 #define SRD (1 << 26) 107 #define SOFTRESET (1 << 1) 108 109 /* PSTATE */ 110 #define DLEV_DAT(x) (1 << (20 + (x))) 111 112 /* Interrupt masks for IE and ISE register */ 113 #define CC_EN (1 << 0) 114 #define TC_EN (1 << 1) 115 #define BWR_EN (1 << 4) 116 #define BRR_EN (1 << 5) 117 #define CIRQ_EN (1 << 8) 118 #define ERR_EN (1 << 15) 119 #define CTO_EN (1 << 16) 120 #define CCRC_EN (1 << 17) 121 #define CEB_EN (1 << 18) 122 #define CIE_EN (1 << 19) 123 #define DTO_EN (1 << 20) 124 #define DCRC_EN (1 << 21) 125 #define DEB_EN (1 << 22) 126 #define ACE_EN (1 << 24) 127 #define CERR_EN (1 << 28) 128 #define BADA_EN (1 << 29) 129 130 #define INT_EN_MASK (BADA_EN | CERR_EN | ACE_EN | DEB_EN | DCRC_EN |\ 131 DTO_EN | CIE_EN | CEB_EN | CCRC_EN | CTO_EN | \ 132 BRR_EN | BWR_EN | TC_EN | CC_EN) 133 134 #define CNI (1 << 7) 135 #define ACIE (1 << 4) 136 #define ACEB (1 << 3) 137 #define ACCE (1 << 2) 138 #define ACTO (1 << 1) 139 #define ACNE (1 << 0) 140 141 #define MMC_AUTOSUSPEND_DELAY 100 142 #define MMC_TIMEOUT_MS 20 /* 20 mSec */ 143 #define MMC_TIMEOUT_US 20000 /* 20000 micro Sec */ 144 #define OMAP_MMC_MIN_CLOCK 400000 145 #define OMAP_MMC_MAX_CLOCK 52000000 146 #define DRIVER_NAME "omap_hsmmc" 147 148 /* 149 * One controller can have multiple slots, like on some omap boards using 150 * omap.c controller driver. Luckily this is not currently done on any known 151 * omap_hsmmc.c device. 152 */ 153 #define mmc_pdata(host) host->pdata 154 155 /* 156 * MMC Host controller read/write API's 157 */ 158 #define OMAP_HSMMC_READ(base, reg) \ 159 __raw_readl((base) + OMAP_HSMMC_##reg) 160 161 #define OMAP_HSMMC_WRITE(base, reg, val) \ 162 __raw_writel((val), (base) + OMAP_HSMMC_##reg) 163 164 struct omap_hsmmc_next { 165 unsigned int dma_len; 166 s32 cookie; 167 }; 168 169 struct omap_hsmmc_host { 170 struct device *dev; 171 struct mmc_host *mmc; 172 struct mmc_request *mrq; 173 struct mmc_command *cmd; 174 struct mmc_data *data; 175 struct clk *fclk; 176 struct clk *dbclk; 177 struct regulator *pbias; 178 bool pbias_enabled; 179 void __iomem *base; 180 int vqmmc_enabled; 181 resource_size_t mapbase; 182 spinlock_t irq_lock; /* Prevent races with irq handler */ 183 unsigned int dma_len; 184 unsigned int dma_sg_idx; 185 unsigned char bus_mode; 186 unsigned char power_mode; 187 int suspended; 188 u32 con; 189 u32 hctl; 190 u32 sysctl; 191 u32 capa; 192 int irq; 193 int wake_irq; 194 int use_dma, dma_ch; 195 struct dma_chan *tx_chan; 196 struct dma_chan *rx_chan; 197 int response_busy; 198 int context_loss; 199 int reqs_blocked; 200 int req_in_progress; 201 unsigned long clk_rate; 202 unsigned int flags; 203 #define AUTO_CMD23 (1 << 0) /* Auto CMD23 support */ 204 #define HSMMC_SDIO_IRQ_ENABLED (1 << 1) /* SDIO irq enabled */ 205 struct omap_hsmmc_next next_data; 206 struct omap_hsmmc_platform_data *pdata; 207 }; 208 209 struct omap_mmc_of_data { 210 u32 reg_offset; 211 u8 controller_flags; 212 }; 213 214 static void omap_hsmmc_start_dma_transfer(struct omap_hsmmc_host *host); 215 216 static int omap_hsmmc_enable_supply(struct mmc_host *mmc) 217 { 218 int ret; 219 struct omap_hsmmc_host *host = mmc_priv(mmc); 220 struct mmc_ios *ios = &mmc->ios; 221 222 if (!IS_ERR(mmc->supply.vmmc)) { 223 ret = mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, ios->vdd); 224 if (ret) 225 return ret; 226 } 227 228 /* Enable interface voltage rail, if needed */ 229 if (!IS_ERR(mmc->supply.vqmmc) && !host->vqmmc_enabled) { 230 ret = regulator_enable(mmc->supply.vqmmc); 231 if (ret) { 232 dev_err(mmc_dev(mmc), "vmmc_aux reg enable failed\n"); 233 goto err_vqmmc; 234 } 235 host->vqmmc_enabled = 1; 236 } 237 238 return 0; 239 240 err_vqmmc: 241 if (!IS_ERR(mmc->supply.vmmc)) 242 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0); 243 244 return ret; 245 } 246 247 static int omap_hsmmc_disable_supply(struct mmc_host *mmc) 248 { 249 int ret; 250 int status; 251 struct omap_hsmmc_host *host = mmc_priv(mmc); 252 253 if (!IS_ERR(mmc->supply.vqmmc) && host->vqmmc_enabled) { 254 ret = regulator_disable(mmc->supply.vqmmc); 255 if (ret) { 256 dev_err(mmc_dev(mmc), "vmmc_aux reg disable failed\n"); 257 return ret; 258 } 259 host->vqmmc_enabled = 0; 260 } 261 262 if (!IS_ERR(mmc->supply.vmmc)) { 263 ret = mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0); 264 if (ret) 265 goto err_set_ocr; 266 } 267 268 return 0; 269 270 err_set_ocr: 271 if (!IS_ERR(mmc->supply.vqmmc)) { 272 status = regulator_enable(mmc->supply.vqmmc); 273 if (status) 274 dev_err(mmc_dev(mmc), "vmmc_aux re-enable failed\n"); 275 } 276 277 return ret; 278 } 279 280 static int omap_hsmmc_set_pbias(struct omap_hsmmc_host *host, bool power_on) 281 { 282 int ret; 283 284 if (IS_ERR(host->pbias)) 285 return 0; 286 287 if (power_on) { 288 if (host->pbias_enabled == 0) { 289 ret = regulator_enable(host->pbias); 290 if (ret) { 291 dev_err(host->dev, "pbias reg enable fail\n"); 292 return ret; 293 } 294 host->pbias_enabled = 1; 295 } 296 } else { 297 if (host->pbias_enabled == 1) { 298 ret = regulator_disable(host->pbias); 299 if (ret) { 300 dev_err(host->dev, "pbias reg disable fail\n"); 301 return ret; 302 } 303 host->pbias_enabled = 0; 304 } 305 } 306 307 return 0; 308 } 309 310 static int omap_hsmmc_set_power(struct omap_hsmmc_host *host, int power_on) 311 { 312 struct mmc_host *mmc = host->mmc; 313 int ret = 0; 314 315 /* 316 * If we don't see a Vcc regulator, assume it's a fixed 317 * voltage always-on regulator. 318 */ 319 if (IS_ERR(mmc->supply.vmmc)) 320 return 0; 321 322 ret = omap_hsmmc_set_pbias(host, false); 323 if (ret) 324 return ret; 325 326 /* 327 * Assume Vcc regulator is used only to power the card ... OMAP 328 * VDDS is used to power the pins, optionally with a transceiver to 329 * support cards using voltages other than VDDS (1.8V nominal). When a 330 * transceiver is used, DAT3..7 are muxed as transceiver control pins. 331 * 332 * In some cases this regulator won't support enable/disable; 333 * e.g. it's a fixed rail for a WLAN chip. 334 * 335 * In other cases vcc_aux switches interface power. Example, for 336 * eMMC cards it represents VccQ. Sometimes transceivers or SDIO 337 * chips/cards need an interface voltage rail too. 338 */ 339 if (power_on) { 340 ret = omap_hsmmc_enable_supply(mmc); 341 if (ret) 342 return ret; 343 344 ret = omap_hsmmc_set_pbias(host, true); 345 if (ret) 346 goto err_set_voltage; 347 } else { 348 ret = omap_hsmmc_disable_supply(mmc); 349 if (ret) 350 return ret; 351 } 352 353 return 0; 354 355 err_set_voltage: 356 omap_hsmmc_disable_supply(mmc); 357 358 return ret; 359 } 360 361 static int omap_hsmmc_disable_boot_regulator(struct regulator *reg) 362 { 363 int ret; 364 365 if (IS_ERR(reg)) 366 return 0; 367 368 if (regulator_is_enabled(reg)) { 369 ret = regulator_enable(reg); 370 if (ret) 371 return ret; 372 373 ret = regulator_disable(reg); 374 if (ret) 375 return ret; 376 } 377 378 return 0; 379 } 380 381 static int omap_hsmmc_disable_boot_regulators(struct omap_hsmmc_host *host) 382 { 383 struct mmc_host *mmc = host->mmc; 384 int ret; 385 386 /* 387 * disable regulators enabled during boot and get the usecount 388 * right so that regulators can be enabled/disabled by checking 389 * the return value of regulator_is_enabled 390 */ 391 ret = omap_hsmmc_disable_boot_regulator(mmc->supply.vmmc); 392 if (ret) { 393 dev_err(host->dev, "fail to disable boot enabled vmmc reg\n"); 394 return ret; 395 } 396 397 ret = omap_hsmmc_disable_boot_regulator(mmc->supply.vqmmc); 398 if (ret) { 399 dev_err(host->dev, 400 "fail to disable boot enabled vmmc_aux reg\n"); 401 return ret; 402 } 403 404 ret = omap_hsmmc_disable_boot_regulator(host->pbias); 405 if (ret) { 406 dev_err(host->dev, 407 "failed to disable boot enabled pbias reg\n"); 408 return ret; 409 } 410 411 return 0; 412 } 413 414 static int omap_hsmmc_reg_get(struct omap_hsmmc_host *host) 415 { 416 int ret; 417 struct mmc_host *mmc = host->mmc; 418 419 420 ret = mmc_regulator_get_supply(mmc); 421 if (ret) 422 return ret; 423 424 /* Allow an aux regulator */ 425 if (IS_ERR(mmc->supply.vqmmc)) { 426 mmc->supply.vqmmc = devm_regulator_get_optional(host->dev, 427 "vmmc_aux"); 428 if (IS_ERR(mmc->supply.vqmmc)) { 429 ret = PTR_ERR(mmc->supply.vqmmc); 430 if ((ret != -ENODEV) && host->dev->of_node) 431 return ret; 432 dev_dbg(host->dev, "unable to get vmmc_aux regulator %ld\n", 433 PTR_ERR(mmc->supply.vqmmc)); 434 } 435 } 436 437 host->pbias = devm_regulator_get_optional(host->dev, "pbias"); 438 if (IS_ERR(host->pbias)) { 439 ret = PTR_ERR(host->pbias); 440 if ((ret != -ENODEV) && host->dev->of_node) { 441 dev_err(host->dev, 442 "SD card detect fail? enable CONFIG_REGULATOR_PBIAS\n"); 443 return ret; 444 } 445 dev_dbg(host->dev, "unable to get pbias regulator %ld\n", 446 PTR_ERR(host->pbias)); 447 } 448 449 /* For eMMC do not power off when not in sleep state */ 450 if (mmc_pdata(host)->no_regulator_off_init) 451 return 0; 452 453 ret = omap_hsmmc_disable_boot_regulators(host); 454 if (ret) 455 return ret; 456 457 return 0; 458 } 459 460 /* 461 * Start clock to the card 462 */ 463 static void omap_hsmmc_start_clock(struct omap_hsmmc_host *host) 464 { 465 OMAP_HSMMC_WRITE(host->base, SYSCTL, 466 OMAP_HSMMC_READ(host->base, SYSCTL) | CEN); 467 } 468 469 /* 470 * Stop clock to the card 471 */ 472 static void omap_hsmmc_stop_clock(struct omap_hsmmc_host *host) 473 { 474 OMAP_HSMMC_WRITE(host->base, SYSCTL, 475 OMAP_HSMMC_READ(host->base, SYSCTL) & ~CEN); 476 if ((OMAP_HSMMC_READ(host->base, SYSCTL) & CEN) != 0x0) 477 dev_dbg(mmc_dev(host->mmc), "MMC Clock is not stopped\n"); 478 } 479 480 static void omap_hsmmc_enable_irq(struct omap_hsmmc_host *host, 481 struct mmc_command *cmd) 482 { 483 u32 irq_mask = INT_EN_MASK; 484 unsigned long flags; 485 486 if (host->use_dma) 487 irq_mask &= ~(BRR_EN | BWR_EN); 488 489 /* Disable timeout for erases */ 490 if (cmd->opcode == MMC_ERASE) 491 irq_mask &= ~DTO_EN; 492 493 spin_lock_irqsave(&host->irq_lock, flags); 494 OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR); 495 OMAP_HSMMC_WRITE(host->base, ISE, irq_mask); 496 497 /* latch pending CIRQ, but don't signal MMC core */ 498 if (host->flags & HSMMC_SDIO_IRQ_ENABLED) 499 irq_mask |= CIRQ_EN; 500 OMAP_HSMMC_WRITE(host->base, IE, irq_mask); 501 spin_unlock_irqrestore(&host->irq_lock, flags); 502 } 503 504 static void omap_hsmmc_disable_irq(struct omap_hsmmc_host *host) 505 { 506 u32 irq_mask = 0; 507 unsigned long flags; 508 509 spin_lock_irqsave(&host->irq_lock, flags); 510 /* no transfer running but need to keep cirq if enabled */ 511 if (host->flags & HSMMC_SDIO_IRQ_ENABLED) 512 irq_mask |= CIRQ_EN; 513 OMAP_HSMMC_WRITE(host->base, ISE, irq_mask); 514 OMAP_HSMMC_WRITE(host->base, IE, irq_mask); 515 OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR); 516 spin_unlock_irqrestore(&host->irq_lock, flags); 517 } 518 519 /* Calculate divisor for the given clock frequency */ 520 static u16 calc_divisor(struct omap_hsmmc_host *host, struct mmc_ios *ios) 521 { 522 u16 dsor = 0; 523 524 if (ios->clock) { 525 dsor = DIV_ROUND_UP(clk_get_rate(host->fclk), ios->clock); 526 if (dsor > CLKD_MAX) 527 dsor = CLKD_MAX; 528 } 529 530 return dsor; 531 } 532 533 static void omap_hsmmc_set_clock(struct omap_hsmmc_host *host) 534 { 535 struct mmc_ios *ios = &host->mmc->ios; 536 unsigned long regval; 537 unsigned long timeout; 538 unsigned long clkdiv; 539 540 dev_vdbg(mmc_dev(host->mmc), "Set clock to %uHz\n", ios->clock); 541 542 omap_hsmmc_stop_clock(host); 543 544 regval = OMAP_HSMMC_READ(host->base, SYSCTL); 545 regval = regval & ~(CLKD_MASK | DTO_MASK); 546 clkdiv = calc_divisor(host, ios); 547 regval = regval | (clkdiv << 6) | (DTO << 16); 548 OMAP_HSMMC_WRITE(host->base, SYSCTL, regval); 549 OMAP_HSMMC_WRITE(host->base, SYSCTL, 550 OMAP_HSMMC_READ(host->base, SYSCTL) | ICE); 551 552 /* Wait till the ICS bit is set */ 553 timeout = jiffies + msecs_to_jiffies(MMC_TIMEOUT_MS); 554 while ((OMAP_HSMMC_READ(host->base, SYSCTL) & ICS) != ICS 555 && time_before(jiffies, timeout)) 556 cpu_relax(); 557 558 /* 559 * Enable High-Speed Support 560 * Pre-Requisites 561 * - Controller should support High-Speed-Enable Bit 562 * - Controller should not be using DDR Mode 563 * - Controller should advertise that it supports High Speed 564 * in capabilities register 565 * - MMC/SD clock coming out of controller > 25MHz 566 */ 567 if ((mmc_pdata(host)->features & HSMMC_HAS_HSPE_SUPPORT) && 568 (ios->timing != MMC_TIMING_MMC_DDR52) && 569 (ios->timing != MMC_TIMING_UHS_DDR50) && 570 ((OMAP_HSMMC_READ(host->base, CAPA) & HSS) == HSS)) { 571 regval = OMAP_HSMMC_READ(host->base, HCTL); 572 if (clkdiv && (clk_get_rate(host->fclk)/clkdiv) > 25000000) 573 regval |= HSPE; 574 else 575 regval &= ~HSPE; 576 577 OMAP_HSMMC_WRITE(host->base, HCTL, regval); 578 } 579 580 omap_hsmmc_start_clock(host); 581 } 582 583 static void omap_hsmmc_set_bus_width(struct omap_hsmmc_host *host) 584 { 585 struct mmc_ios *ios = &host->mmc->ios; 586 u32 con; 587 588 con = OMAP_HSMMC_READ(host->base, CON); 589 if (ios->timing == MMC_TIMING_MMC_DDR52 || 590 ios->timing == MMC_TIMING_UHS_DDR50) 591 con |= DDR; /* configure in DDR mode */ 592 else 593 con &= ~DDR; 594 switch (ios->bus_width) { 595 case MMC_BUS_WIDTH_8: 596 OMAP_HSMMC_WRITE(host->base, CON, con | DW8); 597 break; 598 case MMC_BUS_WIDTH_4: 599 OMAP_HSMMC_WRITE(host->base, CON, con & ~DW8); 600 OMAP_HSMMC_WRITE(host->base, HCTL, 601 OMAP_HSMMC_READ(host->base, HCTL) | FOUR_BIT); 602 break; 603 case MMC_BUS_WIDTH_1: 604 OMAP_HSMMC_WRITE(host->base, CON, con & ~DW8); 605 OMAP_HSMMC_WRITE(host->base, HCTL, 606 OMAP_HSMMC_READ(host->base, HCTL) & ~FOUR_BIT); 607 break; 608 } 609 } 610 611 static void omap_hsmmc_set_bus_mode(struct omap_hsmmc_host *host) 612 { 613 struct mmc_ios *ios = &host->mmc->ios; 614 u32 con; 615 616 con = OMAP_HSMMC_READ(host->base, CON); 617 if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN) 618 OMAP_HSMMC_WRITE(host->base, CON, con | OD); 619 else 620 OMAP_HSMMC_WRITE(host->base, CON, con & ~OD); 621 } 622 623 #ifdef CONFIG_PM 624 625 /* 626 * Restore the MMC host context, if it was lost as result of a 627 * power state change. 628 */ 629 static int omap_hsmmc_context_restore(struct omap_hsmmc_host *host) 630 { 631 struct mmc_ios *ios = &host->mmc->ios; 632 u32 hctl, capa; 633 unsigned long timeout; 634 635 if (host->con == OMAP_HSMMC_READ(host->base, CON) && 636 host->hctl == OMAP_HSMMC_READ(host->base, HCTL) && 637 host->sysctl == OMAP_HSMMC_READ(host->base, SYSCTL) && 638 host->capa == OMAP_HSMMC_READ(host->base, CAPA)) 639 return 0; 640 641 host->context_loss++; 642 643 if (host->pdata->controller_flags & OMAP_HSMMC_SUPPORTS_DUAL_VOLT) { 644 if (host->power_mode != MMC_POWER_OFF && 645 (1 << ios->vdd) <= MMC_VDD_23_24) 646 hctl = SDVS18; 647 else 648 hctl = SDVS30; 649 capa = VS30 | VS18; 650 } else { 651 hctl = SDVS18; 652 capa = VS18; 653 } 654 655 if (host->mmc->caps & MMC_CAP_SDIO_IRQ) 656 hctl |= IWE; 657 658 OMAP_HSMMC_WRITE(host->base, HCTL, 659 OMAP_HSMMC_READ(host->base, HCTL) | hctl); 660 661 OMAP_HSMMC_WRITE(host->base, CAPA, 662 OMAP_HSMMC_READ(host->base, CAPA) | capa); 663 664 OMAP_HSMMC_WRITE(host->base, HCTL, 665 OMAP_HSMMC_READ(host->base, HCTL) | SDBP); 666 667 timeout = jiffies + msecs_to_jiffies(MMC_TIMEOUT_MS); 668 while ((OMAP_HSMMC_READ(host->base, HCTL) & SDBP) != SDBP 669 && time_before(jiffies, timeout)) 670 ; 671 672 OMAP_HSMMC_WRITE(host->base, ISE, 0); 673 OMAP_HSMMC_WRITE(host->base, IE, 0); 674 OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR); 675 676 /* Do not initialize card-specific things if the power is off */ 677 if (host->power_mode == MMC_POWER_OFF) 678 goto out; 679 680 omap_hsmmc_set_bus_width(host); 681 682 omap_hsmmc_set_clock(host); 683 684 omap_hsmmc_set_bus_mode(host); 685 686 out: 687 dev_dbg(mmc_dev(host->mmc), "context is restored: restore count %d\n", 688 host->context_loss); 689 return 0; 690 } 691 692 /* 693 * Save the MMC host context (store the number of power state changes so far). 694 */ 695 static void omap_hsmmc_context_save(struct omap_hsmmc_host *host) 696 { 697 host->con = OMAP_HSMMC_READ(host->base, CON); 698 host->hctl = OMAP_HSMMC_READ(host->base, HCTL); 699 host->sysctl = OMAP_HSMMC_READ(host->base, SYSCTL); 700 host->capa = OMAP_HSMMC_READ(host->base, CAPA); 701 } 702 703 #else 704 705 static int omap_hsmmc_context_restore(struct omap_hsmmc_host *host) 706 { 707 return 0; 708 } 709 710 static void omap_hsmmc_context_save(struct omap_hsmmc_host *host) 711 { 712 } 713 714 #endif 715 716 /* 717 * Send init stream sequence to card 718 * before sending IDLE command 719 */ 720 static void send_init_stream(struct omap_hsmmc_host *host) 721 { 722 int reg = 0; 723 unsigned long timeout; 724 725 disable_irq(host->irq); 726 727 OMAP_HSMMC_WRITE(host->base, IE, INT_EN_MASK); 728 OMAP_HSMMC_WRITE(host->base, CON, 729 OMAP_HSMMC_READ(host->base, CON) | INIT_STREAM); 730 OMAP_HSMMC_WRITE(host->base, CMD, INIT_STREAM_CMD); 731 732 timeout = jiffies + msecs_to_jiffies(MMC_TIMEOUT_MS); 733 while ((reg != CC_EN) && time_before(jiffies, timeout)) 734 reg = OMAP_HSMMC_READ(host->base, STAT) & CC_EN; 735 736 OMAP_HSMMC_WRITE(host->base, CON, 737 OMAP_HSMMC_READ(host->base, CON) & ~INIT_STREAM); 738 739 OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR); 740 OMAP_HSMMC_READ(host->base, STAT); 741 742 enable_irq(host->irq); 743 } 744 745 static ssize_t 746 omap_hsmmc_show_slot_name(struct device *dev, struct device_attribute *attr, 747 char *buf) 748 { 749 struct mmc_host *mmc = container_of(dev, struct mmc_host, class_dev); 750 struct omap_hsmmc_host *host = mmc_priv(mmc); 751 752 return sprintf(buf, "%s\n", mmc_pdata(host)->name); 753 } 754 755 static DEVICE_ATTR(slot_name, S_IRUGO, omap_hsmmc_show_slot_name, NULL); 756 757 /* 758 * Configure the response type and send the cmd. 759 */ 760 static void 761 omap_hsmmc_start_command(struct omap_hsmmc_host *host, struct mmc_command *cmd, 762 struct mmc_data *data) 763 { 764 int cmdreg = 0, resptype = 0, cmdtype = 0; 765 766 dev_vdbg(mmc_dev(host->mmc), "%s: CMD%d, argument 0x%08x\n", 767 mmc_hostname(host->mmc), cmd->opcode, cmd->arg); 768 host->cmd = cmd; 769 770 omap_hsmmc_enable_irq(host, cmd); 771 772 host->response_busy = 0; 773 if (cmd->flags & MMC_RSP_PRESENT) { 774 if (cmd->flags & MMC_RSP_136) 775 resptype = 1; 776 else if (cmd->flags & MMC_RSP_BUSY) { 777 resptype = 3; 778 host->response_busy = 1; 779 } else 780 resptype = 2; 781 } 782 783 /* 784 * Unlike OMAP1 controller, the cmdtype does not seem to be based on 785 * ac, bc, adtc, bcr. Only commands ending an open ended transfer need 786 * a val of 0x3, rest 0x0. 787 */ 788 if (cmd == host->mrq->stop) 789 cmdtype = 0x3; 790 791 cmdreg = (cmd->opcode << 24) | (resptype << 16) | (cmdtype << 22); 792 793 if ((host->flags & AUTO_CMD23) && mmc_op_multi(cmd->opcode) && 794 host->mrq->sbc) { 795 cmdreg |= ACEN_ACMD23; 796 OMAP_HSMMC_WRITE(host->base, SDMASA, host->mrq->sbc->arg); 797 } 798 if (data) { 799 cmdreg |= DP_SELECT | MSBS | BCE; 800 if (data->flags & MMC_DATA_READ) 801 cmdreg |= DDIR; 802 else 803 cmdreg &= ~(DDIR); 804 } 805 806 if (host->use_dma) 807 cmdreg |= DMAE; 808 809 host->req_in_progress = 1; 810 811 OMAP_HSMMC_WRITE(host->base, ARG, cmd->arg); 812 OMAP_HSMMC_WRITE(host->base, CMD, cmdreg); 813 } 814 815 static struct dma_chan *omap_hsmmc_get_dma_chan(struct omap_hsmmc_host *host, 816 struct mmc_data *data) 817 { 818 return data->flags & MMC_DATA_WRITE ? host->tx_chan : host->rx_chan; 819 } 820 821 static void omap_hsmmc_request_done(struct omap_hsmmc_host *host, struct mmc_request *mrq) 822 { 823 int dma_ch; 824 unsigned long flags; 825 826 spin_lock_irqsave(&host->irq_lock, flags); 827 host->req_in_progress = 0; 828 dma_ch = host->dma_ch; 829 spin_unlock_irqrestore(&host->irq_lock, flags); 830 831 omap_hsmmc_disable_irq(host); 832 /* Do not complete the request if DMA is still in progress */ 833 if (mrq->data && host->use_dma && dma_ch != -1) 834 return; 835 host->mrq = NULL; 836 mmc_request_done(host->mmc, mrq); 837 } 838 839 /* 840 * Notify the transfer complete to MMC core 841 */ 842 static void 843 omap_hsmmc_xfer_done(struct omap_hsmmc_host *host, struct mmc_data *data) 844 { 845 if (!data) { 846 struct mmc_request *mrq = host->mrq; 847 848 /* TC before CC from CMD6 - don't know why, but it happens */ 849 if (host->cmd && host->cmd->opcode == 6 && 850 host->response_busy) { 851 host->response_busy = 0; 852 return; 853 } 854 855 omap_hsmmc_request_done(host, mrq); 856 return; 857 } 858 859 host->data = NULL; 860 861 if (!data->error) 862 data->bytes_xfered += data->blocks * (data->blksz); 863 else 864 data->bytes_xfered = 0; 865 866 if (data->stop && (data->error || !host->mrq->sbc)) 867 omap_hsmmc_start_command(host, data->stop, NULL); 868 else 869 omap_hsmmc_request_done(host, data->mrq); 870 } 871 872 /* 873 * Notify the core about command completion 874 */ 875 static void 876 omap_hsmmc_cmd_done(struct omap_hsmmc_host *host, struct mmc_command *cmd) 877 { 878 if (host->mrq->sbc && (host->cmd == host->mrq->sbc) && 879 !host->mrq->sbc->error && !(host->flags & AUTO_CMD23)) { 880 host->cmd = NULL; 881 omap_hsmmc_start_dma_transfer(host); 882 omap_hsmmc_start_command(host, host->mrq->cmd, 883 host->mrq->data); 884 return; 885 } 886 887 host->cmd = NULL; 888 889 if (cmd->flags & MMC_RSP_PRESENT) { 890 if (cmd->flags & MMC_RSP_136) { 891 /* response type 2 */ 892 cmd->resp[3] = OMAP_HSMMC_READ(host->base, RSP10); 893 cmd->resp[2] = OMAP_HSMMC_READ(host->base, RSP32); 894 cmd->resp[1] = OMAP_HSMMC_READ(host->base, RSP54); 895 cmd->resp[0] = OMAP_HSMMC_READ(host->base, RSP76); 896 } else { 897 /* response types 1, 1b, 3, 4, 5, 6 */ 898 cmd->resp[0] = OMAP_HSMMC_READ(host->base, RSP10); 899 } 900 } 901 if ((host->data == NULL && !host->response_busy) || cmd->error) 902 omap_hsmmc_request_done(host, host->mrq); 903 } 904 905 /* 906 * DMA clean up for command errors 907 */ 908 static void omap_hsmmc_dma_cleanup(struct omap_hsmmc_host *host, int errno) 909 { 910 int dma_ch; 911 unsigned long flags; 912 913 host->data->error = errno; 914 915 spin_lock_irqsave(&host->irq_lock, flags); 916 dma_ch = host->dma_ch; 917 host->dma_ch = -1; 918 spin_unlock_irqrestore(&host->irq_lock, flags); 919 920 if (host->use_dma && dma_ch != -1) { 921 struct dma_chan *chan = omap_hsmmc_get_dma_chan(host, host->data); 922 923 dmaengine_terminate_all(chan); 924 dma_unmap_sg(chan->device->dev, 925 host->data->sg, host->data->sg_len, 926 mmc_get_dma_dir(host->data)); 927 928 host->data->host_cookie = 0; 929 } 930 host->data = NULL; 931 } 932 933 /* 934 * Readable error output 935 */ 936 #ifdef CONFIG_MMC_DEBUG 937 static void omap_hsmmc_dbg_report_irq(struct omap_hsmmc_host *host, u32 status) 938 { 939 /* --- means reserved bit without definition at documentation */ 940 static const char *omap_hsmmc_status_bits[] = { 941 "CC" , "TC" , "BGE", "---", "BWR" , "BRR" , "---" , "---" , 942 "CIRQ", "OBI" , "---", "---", "---" , "---" , "---" , "ERRI", 943 "CTO" , "CCRC", "CEB", "CIE", "DTO" , "DCRC", "DEB" , "---" , 944 "ACE" , "---" , "---", "---", "CERR", "BADA", "---" , "---" 945 }; 946 char res[256]; 947 char *buf = res; 948 int len, i; 949 950 len = sprintf(buf, "MMC IRQ 0x%x :", status); 951 buf += len; 952 953 for (i = 0; i < ARRAY_SIZE(omap_hsmmc_status_bits); i++) 954 if (status & (1 << i)) { 955 len = sprintf(buf, " %s", omap_hsmmc_status_bits[i]); 956 buf += len; 957 } 958 959 dev_vdbg(mmc_dev(host->mmc), "%s\n", res); 960 } 961 #else 962 static inline void omap_hsmmc_dbg_report_irq(struct omap_hsmmc_host *host, 963 u32 status) 964 { 965 } 966 #endif /* CONFIG_MMC_DEBUG */ 967 968 /* 969 * MMC controller internal state machines reset 970 * 971 * Used to reset command or data internal state machines, using respectively 972 * SRC or SRD bit of SYSCTL register 973 * Can be called from interrupt context 974 */ 975 static inline void omap_hsmmc_reset_controller_fsm(struct omap_hsmmc_host *host, 976 unsigned long bit) 977 { 978 unsigned long i = 0; 979 unsigned long limit = MMC_TIMEOUT_US; 980 981 OMAP_HSMMC_WRITE(host->base, SYSCTL, 982 OMAP_HSMMC_READ(host->base, SYSCTL) | bit); 983 984 /* 985 * OMAP4 ES2 and greater has an updated reset logic. 986 * Monitor a 0->1 transition first 987 */ 988 if (mmc_pdata(host)->features & HSMMC_HAS_UPDATED_RESET) { 989 while ((!(OMAP_HSMMC_READ(host->base, SYSCTL) & bit)) 990 && (i++ < limit)) 991 udelay(1); 992 } 993 i = 0; 994 995 while ((OMAP_HSMMC_READ(host->base, SYSCTL) & bit) && 996 (i++ < limit)) 997 udelay(1); 998 999 if (OMAP_HSMMC_READ(host->base, SYSCTL) & bit) 1000 dev_err(mmc_dev(host->mmc), 1001 "Timeout waiting on controller reset in %s\n", 1002 __func__); 1003 } 1004 1005 static void hsmmc_command_incomplete(struct omap_hsmmc_host *host, 1006 int err, int end_cmd) 1007 { 1008 if (end_cmd) { 1009 omap_hsmmc_reset_controller_fsm(host, SRC); 1010 if (host->cmd) 1011 host->cmd->error = err; 1012 } 1013 1014 if (host->data) { 1015 omap_hsmmc_reset_controller_fsm(host, SRD); 1016 omap_hsmmc_dma_cleanup(host, err); 1017 } else if (host->mrq && host->mrq->cmd) 1018 host->mrq->cmd->error = err; 1019 } 1020 1021 static void omap_hsmmc_do_irq(struct omap_hsmmc_host *host, int status) 1022 { 1023 struct mmc_data *data; 1024 int end_cmd = 0, end_trans = 0; 1025 int error = 0; 1026 1027 data = host->data; 1028 dev_vdbg(mmc_dev(host->mmc), "IRQ Status is %x\n", status); 1029 1030 if (status & ERR_EN) { 1031 omap_hsmmc_dbg_report_irq(host, status); 1032 1033 if (status & (CTO_EN | CCRC_EN | CEB_EN)) 1034 end_cmd = 1; 1035 if (host->data || host->response_busy) { 1036 end_trans = !end_cmd; 1037 host->response_busy = 0; 1038 } 1039 if (status & (CTO_EN | DTO_EN)) 1040 hsmmc_command_incomplete(host, -ETIMEDOUT, end_cmd); 1041 else if (status & (CCRC_EN | DCRC_EN | DEB_EN | CEB_EN | 1042 BADA_EN)) 1043 hsmmc_command_incomplete(host, -EILSEQ, end_cmd); 1044 1045 if (status & ACE_EN) { 1046 u32 ac12; 1047 ac12 = OMAP_HSMMC_READ(host->base, AC12); 1048 if (!(ac12 & ACNE) && host->mrq->sbc) { 1049 end_cmd = 1; 1050 if (ac12 & ACTO) 1051 error = -ETIMEDOUT; 1052 else if (ac12 & (ACCE | ACEB | ACIE)) 1053 error = -EILSEQ; 1054 host->mrq->sbc->error = error; 1055 hsmmc_command_incomplete(host, error, end_cmd); 1056 } 1057 dev_dbg(mmc_dev(host->mmc), "AC12 err: 0x%x\n", ac12); 1058 } 1059 } 1060 1061 OMAP_HSMMC_WRITE(host->base, STAT, status); 1062 if (end_cmd || ((status & CC_EN) && host->cmd)) 1063 omap_hsmmc_cmd_done(host, host->cmd); 1064 if ((end_trans || (status & TC_EN)) && host->mrq) 1065 omap_hsmmc_xfer_done(host, data); 1066 } 1067 1068 /* 1069 * MMC controller IRQ handler 1070 */ 1071 static irqreturn_t omap_hsmmc_irq(int irq, void *dev_id) 1072 { 1073 struct omap_hsmmc_host *host = dev_id; 1074 int status; 1075 1076 status = OMAP_HSMMC_READ(host->base, STAT); 1077 while (status & (INT_EN_MASK | CIRQ_EN)) { 1078 if (host->req_in_progress) 1079 omap_hsmmc_do_irq(host, status); 1080 1081 if (status & CIRQ_EN) 1082 mmc_signal_sdio_irq(host->mmc); 1083 1084 /* Flush posted write */ 1085 status = OMAP_HSMMC_READ(host->base, STAT); 1086 } 1087 1088 return IRQ_HANDLED; 1089 } 1090 1091 static void set_sd_bus_power(struct omap_hsmmc_host *host) 1092 { 1093 unsigned long i; 1094 1095 OMAP_HSMMC_WRITE(host->base, HCTL, 1096 OMAP_HSMMC_READ(host->base, HCTL) | SDBP); 1097 for (i = 0; i < loops_per_jiffy; i++) { 1098 if (OMAP_HSMMC_READ(host->base, HCTL) & SDBP) 1099 break; 1100 cpu_relax(); 1101 } 1102 } 1103 1104 /* 1105 * Switch MMC interface voltage ... only relevant for MMC1. 1106 * 1107 * MMC2 and MMC3 use fixed 1.8V levels, and maybe a transceiver. 1108 * The MMC2 transceiver controls are used instead of DAT4..DAT7. 1109 * Some chips, like eMMC ones, use internal transceivers. 1110 */ 1111 static int omap_hsmmc_switch_opcond(struct omap_hsmmc_host *host, int vdd) 1112 { 1113 u32 reg_val = 0; 1114 int ret; 1115 1116 /* Disable the clocks */ 1117 clk_disable_unprepare(host->dbclk); 1118 1119 /* Turn the power off */ 1120 ret = omap_hsmmc_set_power(host, 0); 1121 1122 /* Turn the power ON with given VDD 1.8 or 3.0v */ 1123 if (!ret) 1124 ret = omap_hsmmc_set_power(host, 1); 1125 clk_prepare_enable(host->dbclk); 1126 1127 if (ret != 0) 1128 goto err; 1129 1130 OMAP_HSMMC_WRITE(host->base, HCTL, 1131 OMAP_HSMMC_READ(host->base, HCTL) & SDVSCLR); 1132 reg_val = OMAP_HSMMC_READ(host->base, HCTL); 1133 1134 /* 1135 * If a MMC dual voltage card is detected, the set_ios fn calls 1136 * this fn with VDD bit set for 1.8V. Upon card removal from the 1137 * slot, omap_hsmmc_set_ios sets the VDD back to 3V on MMC_POWER_OFF. 1138 * 1139 * Cope with a bit of slop in the range ... per data sheets: 1140 * - "1.8V" for vdds_mmc1/vdds_mmc1a can be up to 2.45V max, 1141 * but recommended values are 1.71V to 1.89V 1142 * - "3.0V" for vdds_mmc1/vdds_mmc1a can be up to 3.5V max, 1143 * but recommended values are 2.7V to 3.3V 1144 * 1145 * Board setup code shouldn't permit anything very out-of-range. 1146 * TWL4030-family VMMC1 and VSIM regulators are fine (avoiding the 1147 * middle range) but VSIM can't power DAT4..DAT7 at more than 3V. 1148 */ 1149 if ((1 << vdd) <= MMC_VDD_23_24) 1150 reg_val |= SDVS18; 1151 else 1152 reg_val |= SDVS30; 1153 1154 OMAP_HSMMC_WRITE(host->base, HCTL, reg_val); 1155 set_sd_bus_power(host); 1156 1157 return 0; 1158 err: 1159 dev_err(mmc_dev(host->mmc), "Unable to switch operating voltage\n"); 1160 return ret; 1161 } 1162 1163 static void omap_hsmmc_dma_callback(void *param) 1164 { 1165 struct omap_hsmmc_host *host = param; 1166 struct dma_chan *chan; 1167 struct mmc_data *data; 1168 int req_in_progress; 1169 1170 spin_lock_irq(&host->irq_lock); 1171 if (host->dma_ch < 0) { 1172 spin_unlock_irq(&host->irq_lock); 1173 return; 1174 } 1175 1176 data = host->mrq->data; 1177 chan = omap_hsmmc_get_dma_chan(host, data); 1178 if (!data->host_cookie) 1179 dma_unmap_sg(chan->device->dev, 1180 data->sg, data->sg_len, 1181 mmc_get_dma_dir(data)); 1182 1183 req_in_progress = host->req_in_progress; 1184 host->dma_ch = -1; 1185 spin_unlock_irq(&host->irq_lock); 1186 1187 /* If DMA has finished after TC, complete the request */ 1188 if (!req_in_progress) { 1189 struct mmc_request *mrq = host->mrq; 1190 1191 host->mrq = NULL; 1192 mmc_request_done(host->mmc, mrq); 1193 } 1194 } 1195 1196 static int omap_hsmmc_pre_dma_transfer(struct omap_hsmmc_host *host, 1197 struct mmc_data *data, 1198 struct omap_hsmmc_next *next, 1199 struct dma_chan *chan) 1200 { 1201 int dma_len; 1202 1203 if (!next && data->host_cookie && 1204 data->host_cookie != host->next_data.cookie) { 1205 dev_warn(host->dev, "[%s] invalid cookie: data->host_cookie %d" 1206 " host->next_data.cookie %d\n", 1207 __func__, data->host_cookie, host->next_data.cookie); 1208 data->host_cookie = 0; 1209 } 1210 1211 /* Check if next job is already prepared */ 1212 if (next || data->host_cookie != host->next_data.cookie) { 1213 dma_len = dma_map_sg(chan->device->dev, data->sg, data->sg_len, 1214 mmc_get_dma_dir(data)); 1215 1216 } else { 1217 dma_len = host->next_data.dma_len; 1218 host->next_data.dma_len = 0; 1219 } 1220 1221 1222 if (dma_len == 0) 1223 return -EINVAL; 1224 1225 if (next) { 1226 next->dma_len = dma_len; 1227 data->host_cookie = ++next->cookie < 0 ? 1 : next->cookie; 1228 } else 1229 host->dma_len = dma_len; 1230 1231 return 0; 1232 } 1233 1234 /* 1235 * Routine to configure and start DMA for the MMC card 1236 */ 1237 static int omap_hsmmc_setup_dma_transfer(struct omap_hsmmc_host *host, 1238 struct mmc_request *req) 1239 { 1240 struct dma_async_tx_descriptor *tx; 1241 int ret = 0, i; 1242 struct mmc_data *data = req->data; 1243 struct dma_chan *chan; 1244 struct dma_slave_config cfg = { 1245 .src_addr = host->mapbase + OMAP_HSMMC_DATA, 1246 .dst_addr = host->mapbase + OMAP_HSMMC_DATA, 1247 .src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES, 1248 .dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES, 1249 .src_maxburst = data->blksz / 4, 1250 .dst_maxburst = data->blksz / 4, 1251 }; 1252 1253 /* Sanity check: all the SG entries must be aligned by block size. */ 1254 for (i = 0; i < data->sg_len; i++) { 1255 struct scatterlist *sgl; 1256 1257 sgl = data->sg + i; 1258 if (sgl->length % data->blksz) 1259 return -EINVAL; 1260 } 1261 if ((data->blksz % 4) != 0) 1262 /* REVISIT: The MMC buffer increments only when MSB is written. 1263 * Return error for blksz which is non multiple of four. 1264 */ 1265 return -EINVAL; 1266 1267 BUG_ON(host->dma_ch != -1); 1268 1269 chan = omap_hsmmc_get_dma_chan(host, data); 1270 1271 ret = dmaengine_slave_config(chan, &cfg); 1272 if (ret) 1273 return ret; 1274 1275 ret = omap_hsmmc_pre_dma_transfer(host, data, NULL, chan); 1276 if (ret) 1277 return ret; 1278 1279 tx = dmaengine_prep_slave_sg(chan, data->sg, data->sg_len, 1280 data->flags & MMC_DATA_WRITE ? DMA_MEM_TO_DEV : DMA_DEV_TO_MEM, 1281 DMA_PREP_INTERRUPT | DMA_CTRL_ACK); 1282 if (!tx) { 1283 dev_err(mmc_dev(host->mmc), "prep_slave_sg() failed\n"); 1284 /* FIXME: cleanup */ 1285 return -1; 1286 } 1287 1288 tx->callback = omap_hsmmc_dma_callback; 1289 tx->callback_param = host; 1290 1291 /* Does not fail */ 1292 dmaengine_submit(tx); 1293 1294 host->dma_ch = 1; 1295 1296 return 0; 1297 } 1298 1299 static void set_data_timeout(struct omap_hsmmc_host *host, 1300 unsigned long long timeout_ns, 1301 unsigned int timeout_clks) 1302 { 1303 unsigned long long timeout = timeout_ns; 1304 unsigned int cycle_ns; 1305 uint32_t reg, clkd, dto = 0; 1306 1307 reg = OMAP_HSMMC_READ(host->base, SYSCTL); 1308 clkd = (reg & CLKD_MASK) >> CLKD_SHIFT; 1309 if (clkd == 0) 1310 clkd = 1; 1311 1312 cycle_ns = 1000000000 / (host->clk_rate / clkd); 1313 do_div(timeout, cycle_ns); 1314 timeout += timeout_clks; 1315 if (timeout) { 1316 while ((timeout & 0x80000000) == 0) { 1317 dto += 1; 1318 timeout <<= 1; 1319 } 1320 dto = 31 - dto; 1321 timeout <<= 1; 1322 if (timeout && dto) 1323 dto += 1; 1324 if (dto >= 13) 1325 dto -= 13; 1326 else 1327 dto = 0; 1328 if (dto > 14) 1329 dto = 14; 1330 } 1331 1332 reg &= ~DTO_MASK; 1333 reg |= dto << DTO_SHIFT; 1334 OMAP_HSMMC_WRITE(host->base, SYSCTL, reg); 1335 } 1336 1337 static void omap_hsmmc_start_dma_transfer(struct omap_hsmmc_host *host) 1338 { 1339 struct mmc_request *req = host->mrq; 1340 struct dma_chan *chan; 1341 1342 if (!req->data) 1343 return; 1344 OMAP_HSMMC_WRITE(host->base, BLK, (req->data->blksz) 1345 | (req->data->blocks << 16)); 1346 set_data_timeout(host, req->data->timeout_ns, 1347 req->data->timeout_clks); 1348 chan = omap_hsmmc_get_dma_chan(host, req->data); 1349 dma_async_issue_pending(chan); 1350 } 1351 1352 /* 1353 * Configure block length for MMC/SD cards and initiate the transfer. 1354 */ 1355 static int 1356 omap_hsmmc_prepare_data(struct omap_hsmmc_host *host, struct mmc_request *req) 1357 { 1358 int ret; 1359 unsigned long long timeout; 1360 1361 host->data = req->data; 1362 1363 if (req->data == NULL) { 1364 OMAP_HSMMC_WRITE(host->base, BLK, 0); 1365 if (req->cmd->flags & MMC_RSP_BUSY) { 1366 timeout = req->cmd->busy_timeout * NSEC_PER_MSEC; 1367 1368 /* 1369 * Set an arbitrary 100ms data timeout for commands with 1370 * busy signal and no indication of busy_timeout. 1371 */ 1372 if (!timeout) 1373 timeout = 100000000U; 1374 1375 set_data_timeout(host, timeout, 0); 1376 } 1377 return 0; 1378 } 1379 1380 if (host->use_dma) { 1381 ret = omap_hsmmc_setup_dma_transfer(host, req); 1382 if (ret != 0) { 1383 dev_err(mmc_dev(host->mmc), "MMC start dma failure\n"); 1384 return ret; 1385 } 1386 } 1387 return 0; 1388 } 1389 1390 static void omap_hsmmc_post_req(struct mmc_host *mmc, struct mmc_request *mrq, 1391 int err) 1392 { 1393 struct omap_hsmmc_host *host = mmc_priv(mmc); 1394 struct mmc_data *data = mrq->data; 1395 1396 if (host->use_dma && data->host_cookie) { 1397 struct dma_chan *c = omap_hsmmc_get_dma_chan(host, data); 1398 1399 dma_unmap_sg(c->device->dev, data->sg, data->sg_len, 1400 mmc_get_dma_dir(data)); 1401 data->host_cookie = 0; 1402 } 1403 } 1404 1405 static void omap_hsmmc_pre_req(struct mmc_host *mmc, struct mmc_request *mrq) 1406 { 1407 struct omap_hsmmc_host *host = mmc_priv(mmc); 1408 1409 if (mrq->data->host_cookie) { 1410 mrq->data->host_cookie = 0; 1411 return ; 1412 } 1413 1414 if (host->use_dma) { 1415 struct dma_chan *c = omap_hsmmc_get_dma_chan(host, mrq->data); 1416 1417 if (omap_hsmmc_pre_dma_transfer(host, mrq->data, 1418 &host->next_data, c)) 1419 mrq->data->host_cookie = 0; 1420 } 1421 } 1422 1423 /* 1424 * Request function. for read/write operation 1425 */ 1426 static void omap_hsmmc_request(struct mmc_host *mmc, struct mmc_request *req) 1427 { 1428 struct omap_hsmmc_host *host = mmc_priv(mmc); 1429 int err; 1430 1431 BUG_ON(host->req_in_progress); 1432 BUG_ON(host->dma_ch != -1); 1433 if (host->reqs_blocked) 1434 host->reqs_blocked = 0; 1435 WARN_ON(host->mrq != NULL); 1436 host->mrq = req; 1437 host->clk_rate = clk_get_rate(host->fclk); 1438 err = omap_hsmmc_prepare_data(host, req); 1439 if (err) { 1440 req->cmd->error = err; 1441 if (req->data) 1442 req->data->error = err; 1443 host->mrq = NULL; 1444 mmc_request_done(mmc, req); 1445 return; 1446 } 1447 if (req->sbc && !(host->flags & AUTO_CMD23)) { 1448 omap_hsmmc_start_command(host, req->sbc, NULL); 1449 return; 1450 } 1451 1452 omap_hsmmc_start_dma_transfer(host); 1453 omap_hsmmc_start_command(host, req->cmd, req->data); 1454 } 1455 1456 /* Routine to configure clock values. Exposed API to core */ 1457 static void omap_hsmmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) 1458 { 1459 struct omap_hsmmc_host *host = mmc_priv(mmc); 1460 int do_send_init_stream = 0; 1461 1462 if (ios->power_mode != host->power_mode) { 1463 switch (ios->power_mode) { 1464 case MMC_POWER_OFF: 1465 omap_hsmmc_set_power(host, 0); 1466 break; 1467 case MMC_POWER_UP: 1468 omap_hsmmc_set_power(host, 1); 1469 break; 1470 case MMC_POWER_ON: 1471 do_send_init_stream = 1; 1472 break; 1473 } 1474 host->power_mode = ios->power_mode; 1475 } 1476 1477 /* FIXME: set registers based only on changes to ios */ 1478 1479 omap_hsmmc_set_bus_width(host); 1480 1481 if (host->pdata->controller_flags & OMAP_HSMMC_SUPPORTS_DUAL_VOLT) { 1482 /* Only MMC1 can interface at 3V without some flavor 1483 * of external transceiver; but they all handle 1.8V. 1484 */ 1485 if ((OMAP_HSMMC_READ(host->base, HCTL) & SDVSDET) && 1486 (ios->vdd == DUAL_VOLT_OCR_BIT)) { 1487 /* 1488 * The mmc_select_voltage fn of the core does 1489 * not seem to set the power_mode to 1490 * MMC_POWER_UP upon recalculating the voltage. 1491 * vdd 1.8v. 1492 */ 1493 if (omap_hsmmc_switch_opcond(host, ios->vdd) != 0) 1494 dev_dbg(mmc_dev(host->mmc), 1495 "Switch operation failed\n"); 1496 } 1497 } 1498 1499 omap_hsmmc_set_clock(host); 1500 1501 if (do_send_init_stream) 1502 send_init_stream(host); 1503 1504 omap_hsmmc_set_bus_mode(host); 1505 } 1506 1507 static void omap_hsmmc_init_card(struct mmc_host *mmc, struct mmc_card *card) 1508 { 1509 struct omap_hsmmc_host *host = mmc_priv(mmc); 1510 1511 if (card->type == MMC_TYPE_SDIO || card->type == MMC_TYPE_SD_COMBO) { 1512 struct device_node *np = mmc_dev(mmc)->of_node; 1513 1514 /* 1515 * REVISIT: should be moved to sdio core and made more 1516 * general e.g. by expanding the DT bindings of child nodes 1517 * to provide a mechanism to provide this information: 1518 * Documentation/devicetree/bindings/mmc/mmc-card.txt 1519 */ 1520 1521 np = of_get_compatible_child(np, "ti,wl1251"); 1522 if (np) { 1523 /* 1524 * We have TI wl1251 attached to MMC3. Pass this 1525 * information to the SDIO core because it can't be 1526 * probed by normal methods. 1527 */ 1528 1529 dev_info(host->dev, "found wl1251\n"); 1530 card->quirks |= MMC_QUIRK_NONSTD_SDIO; 1531 card->cccr.wide_bus = 1; 1532 card->cis.vendor = 0x104c; 1533 card->cis.device = 0x9066; 1534 card->cis.blksize = 512; 1535 card->cis.max_dtr = 24000000; 1536 card->ocr = 0x80; 1537 of_node_put(np); 1538 } 1539 } 1540 } 1541 1542 static void omap_hsmmc_enable_sdio_irq(struct mmc_host *mmc, int enable) 1543 { 1544 struct omap_hsmmc_host *host = mmc_priv(mmc); 1545 u32 irq_mask, con; 1546 unsigned long flags; 1547 1548 spin_lock_irqsave(&host->irq_lock, flags); 1549 1550 con = OMAP_HSMMC_READ(host->base, CON); 1551 irq_mask = OMAP_HSMMC_READ(host->base, ISE); 1552 if (enable) { 1553 host->flags |= HSMMC_SDIO_IRQ_ENABLED; 1554 irq_mask |= CIRQ_EN; 1555 con |= CTPL | CLKEXTFREE; 1556 } else { 1557 host->flags &= ~HSMMC_SDIO_IRQ_ENABLED; 1558 irq_mask &= ~CIRQ_EN; 1559 con &= ~(CTPL | CLKEXTFREE); 1560 } 1561 OMAP_HSMMC_WRITE(host->base, CON, con); 1562 OMAP_HSMMC_WRITE(host->base, IE, irq_mask); 1563 1564 /* 1565 * if enable, piggy back detection on current request 1566 * but always disable immediately 1567 */ 1568 if (!host->req_in_progress || !enable) 1569 OMAP_HSMMC_WRITE(host->base, ISE, irq_mask); 1570 1571 /* flush posted write */ 1572 OMAP_HSMMC_READ(host->base, IE); 1573 1574 spin_unlock_irqrestore(&host->irq_lock, flags); 1575 } 1576 1577 static int omap_hsmmc_configure_wake_irq(struct omap_hsmmc_host *host) 1578 { 1579 int ret; 1580 1581 /* 1582 * For omaps with wake-up path, wakeirq will be irq from pinctrl and 1583 * for other omaps, wakeirq will be from GPIO (dat line remuxed to 1584 * gpio). wakeirq is needed to detect sdio irq in runtime suspend state 1585 * with functional clock disabled. 1586 */ 1587 if (!host->dev->of_node || !host->wake_irq) 1588 return -ENODEV; 1589 1590 ret = dev_pm_set_dedicated_wake_irq(host->dev, host->wake_irq); 1591 if (ret) { 1592 dev_err(mmc_dev(host->mmc), "Unable to request wake IRQ\n"); 1593 goto err; 1594 } 1595 1596 /* 1597 * Some omaps don't have wake-up path from deeper idle states 1598 * and need to remux SDIO DAT1 to GPIO for wake-up from idle. 1599 */ 1600 if (host->pdata->controller_flags & OMAP_HSMMC_SWAKEUP_MISSING) { 1601 struct pinctrl *p = devm_pinctrl_get(host->dev); 1602 if (IS_ERR(p)) { 1603 ret = PTR_ERR(p); 1604 goto err_free_irq; 1605 } 1606 1607 if (IS_ERR(pinctrl_lookup_state(p, PINCTRL_STATE_IDLE))) { 1608 dev_info(host->dev, "missing idle pinctrl state\n"); 1609 devm_pinctrl_put(p); 1610 ret = -EINVAL; 1611 goto err_free_irq; 1612 } 1613 devm_pinctrl_put(p); 1614 } 1615 1616 OMAP_HSMMC_WRITE(host->base, HCTL, 1617 OMAP_HSMMC_READ(host->base, HCTL) | IWE); 1618 return 0; 1619 1620 err_free_irq: 1621 dev_pm_clear_wake_irq(host->dev); 1622 err: 1623 dev_warn(host->dev, "no SDIO IRQ support, falling back to polling\n"); 1624 host->wake_irq = 0; 1625 return ret; 1626 } 1627 1628 static void omap_hsmmc_conf_bus_power(struct omap_hsmmc_host *host) 1629 { 1630 u32 hctl, capa, value; 1631 1632 /* Only MMC1 supports 3.0V */ 1633 if (host->pdata->controller_flags & OMAP_HSMMC_SUPPORTS_DUAL_VOLT) { 1634 hctl = SDVS30; 1635 capa = VS30 | VS18; 1636 } else { 1637 hctl = SDVS18; 1638 capa = VS18; 1639 } 1640 1641 value = OMAP_HSMMC_READ(host->base, HCTL) & ~SDVS_MASK; 1642 OMAP_HSMMC_WRITE(host->base, HCTL, value | hctl); 1643 1644 value = OMAP_HSMMC_READ(host->base, CAPA); 1645 OMAP_HSMMC_WRITE(host->base, CAPA, value | capa); 1646 1647 /* Set SD bus power bit */ 1648 set_sd_bus_power(host); 1649 } 1650 1651 static int omap_hsmmc_multi_io_quirk(struct mmc_card *card, 1652 unsigned int direction, int blk_size) 1653 { 1654 /* This controller can't do multiblock reads due to hw bugs */ 1655 if (direction == MMC_DATA_READ) 1656 return 1; 1657 1658 return blk_size; 1659 } 1660 1661 static struct mmc_host_ops omap_hsmmc_ops = { 1662 .post_req = omap_hsmmc_post_req, 1663 .pre_req = omap_hsmmc_pre_req, 1664 .request = omap_hsmmc_request, 1665 .set_ios = omap_hsmmc_set_ios, 1666 .get_cd = mmc_gpio_get_cd, 1667 .get_ro = mmc_gpio_get_ro, 1668 .init_card = omap_hsmmc_init_card, 1669 .enable_sdio_irq = omap_hsmmc_enable_sdio_irq, 1670 }; 1671 1672 #ifdef CONFIG_DEBUG_FS 1673 1674 static int mmc_regs_show(struct seq_file *s, void *data) 1675 { 1676 struct mmc_host *mmc = s->private; 1677 struct omap_hsmmc_host *host = mmc_priv(mmc); 1678 1679 seq_printf(s, "mmc%d:\n", mmc->index); 1680 seq_printf(s, "sdio irq mode\t%s\n", 1681 (mmc->caps & MMC_CAP_SDIO_IRQ) ? "interrupt" : "polling"); 1682 1683 if (mmc->caps & MMC_CAP_SDIO_IRQ) { 1684 seq_printf(s, "sdio irq \t%s\n", 1685 (host->flags & HSMMC_SDIO_IRQ_ENABLED) ? "enabled" 1686 : "disabled"); 1687 } 1688 seq_printf(s, "ctx_loss:\t%d\n", host->context_loss); 1689 1690 pm_runtime_get_sync(host->dev); 1691 seq_puts(s, "\nregs:\n"); 1692 seq_printf(s, "CON:\t\t0x%08x\n", 1693 OMAP_HSMMC_READ(host->base, CON)); 1694 seq_printf(s, "PSTATE:\t\t0x%08x\n", 1695 OMAP_HSMMC_READ(host->base, PSTATE)); 1696 seq_printf(s, "HCTL:\t\t0x%08x\n", 1697 OMAP_HSMMC_READ(host->base, HCTL)); 1698 seq_printf(s, "SYSCTL:\t\t0x%08x\n", 1699 OMAP_HSMMC_READ(host->base, SYSCTL)); 1700 seq_printf(s, "IE:\t\t0x%08x\n", 1701 OMAP_HSMMC_READ(host->base, IE)); 1702 seq_printf(s, "ISE:\t\t0x%08x\n", 1703 OMAP_HSMMC_READ(host->base, ISE)); 1704 seq_printf(s, "CAPA:\t\t0x%08x\n", 1705 OMAP_HSMMC_READ(host->base, CAPA)); 1706 1707 pm_runtime_mark_last_busy(host->dev); 1708 pm_runtime_put_autosuspend(host->dev); 1709 1710 return 0; 1711 } 1712 1713 DEFINE_SHOW_ATTRIBUTE(mmc_regs); 1714 1715 static void omap_hsmmc_debugfs(struct mmc_host *mmc) 1716 { 1717 if (mmc->debugfs_root) 1718 debugfs_create_file("regs", S_IRUSR, mmc->debugfs_root, 1719 mmc, &mmc_regs_fops); 1720 } 1721 1722 #else 1723 1724 static void omap_hsmmc_debugfs(struct mmc_host *mmc) 1725 { 1726 } 1727 1728 #endif 1729 1730 #ifdef CONFIG_OF 1731 static const struct omap_mmc_of_data omap3_pre_es3_mmc_of_data = { 1732 /* See 35xx errata 2.1.1.128 in SPRZ278F */ 1733 .controller_flags = OMAP_HSMMC_BROKEN_MULTIBLOCK_READ, 1734 }; 1735 1736 static const struct omap_mmc_of_data omap4_mmc_of_data = { 1737 .reg_offset = 0x100, 1738 }; 1739 static const struct omap_mmc_of_data am33xx_mmc_of_data = { 1740 .reg_offset = 0x100, 1741 .controller_flags = OMAP_HSMMC_SWAKEUP_MISSING, 1742 }; 1743 1744 static const struct of_device_id omap_mmc_of_match[] = { 1745 { 1746 .compatible = "ti,omap2-hsmmc", 1747 }, 1748 { 1749 .compatible = "ti,omap3-pre-es3-hsmmc", 1750 .data = &omap3_pre_es3_mmc_of_data, 1751 }, 1752 { 1753 .compatible = "ti,omap3-hsmmc", 1754 }, 1755 { 1756 .compatible = "ti,omap4-hsmmc", 1757 .data = &omap4_mmc_of_data, 1758 }, 1759 { 1760 .compatible = "ti,am33xx-hsmmc", 1761 .data = &am33xx_mmc_of_data, 1762 }, 1763 {}, 1764 }; 1765 MODULE_DEVICE_TABLE(of, omap_mmc_of_match); 1766 1767 static struct omap_hsmmc_platform_data *of_get_hsmmc_pdata(struct device *dev) 1768 { 1769 struct omap_hsmmc_platform_data *pdata, *legacy; 1770 struct device_node *np = dev->of_node; 1771 1772 pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL); 1773 if (!pdata) 1774 return ERR_PTR(-ENOMEM); /* out of memory */ 1775 1776 legacy = dev_get_platdata(dev); 1777 if (legacy && legacy->name) 1778 pdata->name = legacy->name; 1779 1780 if (of_find_property(np, "ti,dual-volt", NULL)) 1781 pdata->controller_flags |= OMAP_HSMMC_SUPPORTS_DUAL_VOLT; 1782 1783 if (of_find_property(np, "ti,non-removable", NULL)) { 1784 pdata->nonremovable = true; 1785 pdata->no_regulator_off_init = true; 1786 } 1787 1788 if (of_find_property(np, "ti,needs-special-reset", NULL)) 1789 pdata->features |= HSMMC_HAS_UPDATED_RESET; 1790 1791 if (of_find_property(np, "ti,needs-special-hs-handling", NULL)) 1792 pdata->features |= HSMMC_HAS_HSPE_SUPPORT; 1793 1794 return pdata; 1795 } 1796 #else 1797 static inline struct omap_hsmmc_platform_data 1798 *of_get_hsmmc_pdata(struct device *dev) 1799 { 1800 return ERR_PTR(-EINVAL); 1801 } 1802 #endif 1803 1804 static int omap_hsmmc_probe(struct platform_device *pdev) 1805 { 1806 struct omap_hsmmc_platform_data *pdata = pdev->dev.platform_data; 1807 struct mmc_host *mmc; 1808 struct omap_hsmmc_host *host = NULL; 1809 struct resource *res; 1810 int ret, irq; 1811 const struct of_device_id *match; 1812 const struct omap_mmc_of_data *data; 1813 void __iomem *base; 1814 1815 match = of_match_device(of_match_ptr(omap_mmc_of_match), &pdev->dev); 1816 if (match) { 1817 pdata = of_get_hsmmc_pdata(&pdev->dev); 1818 1819 if (IS_ERR(pdata)) 1820 return PTR_ERR(pdata); 1821 1822 if (match->data) { 1823 data = match->data; 1824 pdata->reg_offset = data->reg_offset; 1825 pdata->controller_flags |= data->controller_flags; 1826 } 1827 } 1828 1829 if (pdata == NULL) { 1830 dev_err(&pdev->dev, "Platform Data is missing\n"); 1831 return -ENXIO; 1832 } 1833 1834 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 1835 irq = platform_get_irq(pdev, 0); 1836 if (res == NULL || irq < 0) 1837 return -ENXIO; 1838 1839 base = devm_ioremap_resource(&pdev->dev, res); 1840 if (IS_ERR(base)) 1841 return PTR_ERR(base); 1842 1843 mmc = mmc_alloc_host(sizeof(struct omap_hsmmc_host), &pdev->dev); 1844 if (!mmc) { 1845 ret = -ENOMEM; 1846 goto err; 1847 } 1848 1849 ret = mmc_of_parse(mmc); 1850 if (ret) 1851 goto err1; 1852 1853 host = mmc_priv(mmc); 1854 host->mmc = mmc; 1855 host->pdata = pdata; 1856 host->dev = &pdev->dev; 1857 host->use_dma = 1; 1858 host->dma_ch = -1; 1859 host->irq = irq; 1860 host->mapbase = res->start + pdata->reg_offset; 1861 host->base = base + pdata->reg_offset; 1862 host->power_mode = MMC_POWER_OFF; 1863 host->next_data.cookie = 1; 1864 host->pbias_enabled = 0; 1865 host->vqmmc_enabled = 0; 1866 1867 platform_set_drvdata(pdev, host); 1868 1869 if (pdev->dev.of_node) 1870 host->wake_irq = irq_of_parse_and_map(pdev->dev.of_node, 1); 1871 1872 mmc->ops = &omap_hsmmc_ops; 1873 1874 mmc->f_min = OMAP_MMC_MIN_CLOCK; 1875 1876 if (pdata->max_freq > 0) 1877 mmc->f_max = pdata->max_freq; 1878 else if (mmc->f_max == 0) 1879 mmc->f_max = OMAP_MMC_MAX_CLOCK; 1880 1881 spin_lock_init(&host->irq_lock); 1882 1883 host->fclk = devm_clk_get(&pdev->dev, "fck"); 1884 if (IS_ERR(host->fclk)) { 1885 ret = PTR_ERR(host->fclk); 1886 host->fclk = NULL; 1887 goto err1; 1888 } 1889 1890 if (host->pdata->controller_flags & OMAP_HSMMC_BROKEN_MULTIBLOCK_READ) { 1891 dev_info(&pdev->dev, "multiblock reads disabled due to 35xx erratum 2.1.1.128; MMC read performance may suffer\n"); 1892 omap_hsmmc_ops.multi_io_quirk = omap_hsmmc_multi_io_quirk; 1893 } 1894 1895 device_init_wakeup(&pdev->dev, true); 1896 pm_runtime_enable(host->dev); 1897 pm_runtime_get_sync(host->dev); 1898 pm_runtime_set_autosuspend_delay(host->dev, MMC_AUTOSUSPEND_DELAY); 1899 pm_runtime_use_autosuspend(host->dev); 1900 1901 omap_hsmmc_context_save(host); 1902 1903 host->dbclk = devm_clk_get(&pdev->dev, "mmchsdb_fck"); 1904 /* 1905 * MMC can still work without debounce clock. 1906 */ 1907 if (IS_ERR(host->dbclk)) { 1908 host->dbclk = NULL; 1909 } else if (clk_prepare_enable(host->dbclk) != 0) { 1910 dev_warn(mmc_dev(host->mmc), "Failed to enable debounce clk\n"); 1911 host->dbclk = NULL; 1912 } 1913 1914 /* Set this to a value that allows allocating an entire descriptor 1915 * list within a page (zero order allocation). */ 1916 mmc->max_segs = 64; 1917 1918 mmc->max_blk_size = 512; /* Block Length at max can be 1024 */ 1919 mmc->max_blk_count = 0xFFFF; /* No. of Blocks is 16 bits */ 1920 mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count; 1921 1922 mmc->caps |= MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED | 1923 MMC_CAP_WAIT_WHILE_BUSY | MMC_CAP_CMD23; 1924 1925 mmc->caps |= mmc_pdata(host)->caps; 1926 if (mmc->caps & MMC_CAP_8_BIT_DATA) 1927 mmc->caps |= MMC_CAP_4_BIT_DATA; 1928 1929 if (mmc_pdata(host)->nonremovable) 1930 mmc->caps |= MMC_CAP_NONREMOVABLE; 1931 1932 mmc->pm_caps |= mmc_pdata(host)->pm_caps; 1933 1934 omap_hsmmc_conf_bus_power(host); 1935 1936 host->rx_chan = dma_request_chan(&pdev->dev, "rx"); 1937 if (IS_ERR(host->rx_chan)) { 1938 dev_err(mmc_dev(host->mmc), "RX DMA channel request failed\n"); 1939 ret = PTR_ERR(host->rx_chan); 1940 goto err_irq; 1941 } 1942 1943 host->tx_chan = dma_request_chan(&pdev->dev, "tx"); 1944 if (IS_ERR(host->tx_chan)) { 1945 dev_err(mmc_dev(host->mmc), "TX DMA channel request failed\n"); 1946 ret = PTR_ERR(host->tx_chan); 1947 goto err_irq; 1948 } 1949 1950 /* 1951 * Limit the maximum segment size to the lower of the request size 1952 * and the DMA engine device segment size limits. In reality, with 1953 * 32-bit transfers, the DMA engine can do longer segments than this 1954 * but there is no way to represent that in the DMA model - if we 1955 * increase this figure here, we get warnings from the DMA API debug. 1956 */ 1957 mmc->max_seg_size = min3(mmc->max_req_size, 1958 dma_get_max_seg_size(host->rx_chan->device->dev), 1959 dma_get_max_seg_size(host->tx_chan->device->dev)); 1960 1961 /* Request IRQ for MMC operations */ 1962 ret = devm_request_irq(&pdev->dev, host->irq, omap_hsmmc_irq, 0, 1963 mmc_hostname(mmc), host); 1964 if (ret) { 1965 dev_err(mmc_dev(host->mmc), "Unable to grab HSMMC IRQ\n"); 1966 goto err_irq; 1967 } 1968 1969 ret = omap_hsmmc_reg_get(host); 1970 if (ret) 1971 goto err_irq; 1972 1973 if (!mmc->ocr_avail) 1974 mmc->ocr_avail = mmc_pdata(host)->ocr_mask; 1975 1976 omap_hsmmc_disable_irq(host); 1977 1978 /* 1979 * For now, only support SDIO interrupt if we have a separate 1980 * wake-up interrupt configured from device tree. This is because 1981 * the wake-up interrupt is needed for idle state and some 1982 * platforms need special quirks. And we don't want to add new 1983 * legacy mux platform init code callbacks any longer as we 1984 * are moving to DT based booting anyways. 1985 */ 1986 ret = omap_hsmmc_configure_wake_irq(host); 1987 if (!ret) 1988 mmc->caps |= MMC_CAP_SDIO_IRQ; 1989 1990 mmc_add_host(mmc); 1991 1992 if (mmc_pdata(host)->name != NULL) { 1993 ret = device_create_file(&mmc->class_dev, &dev_attr_slot_name); 1994 if (ret < 0) 1995 goto err_slot_name; 1996 } 1997 1998 omap_hsmmc_debugfs(mmc); 1999 pm_runtime_mark_last_busy(host->dev); 2000 pm_runtime_put_autosuspend(host->dev); 2001 2002 return 0; 2003 2004 err_slot_name: 2005 mmc_remove_host(mmc); 2006 err_irq: 2007 device_init_wakeup(&pdev->dev, false); 2008 if (!IS_ERR_OR_NULL(host->tx_chan)) 2009 dma_release_channel(host->tx_chan); 2010 if (!IS_ERR_OR_NULL(host->rx_chan)) 2011 dma_release_channel(host->rx_chan); 2012 pm_runtime_dont_use_autosuspend(host->dev); 2013 pm_runtime_put_sync(host->dev); 2014 pm_runtime_disable(host->dev); 2015 clk_disable_unprepare(host->dbclk); 2016 err1: 2017 mmc_free_host(mmc); 2018 err: 2019 return ret; 2020 } 2021 2022 static int omap_hsmmc_remove(struct platform_device *pdev) 2023 { 2024 struct omap_hsmmc_host *host = platform_get_drvdata(pdev); 2025 2026 pm_runtime_get_sync(host->dev); 2027 mmc_remove_host(host->mmc); 2028 2029 dma_release_channel(host->tx_chan); 2030 dma_release_channel(host->rx_chan); 2031 2032 dev_pm_clear_wake_irq(host->dev); 2033 pm_runtime_dont_use_autosuspend(host->dev); 2034 pm_runtime_put_sync(host->dev); 2035 pm_runtime_disable(host->dev); 2036 device_init_wakeup(&pdev->dev, false); 2037 clk_disable_unprepare(host->dbclk); 2038 2039 mmc_free_host(host->mmc); 2040 2041 return 0; 2042 } 2043 2044 #ifdef CONFIG_PM_SLEEP 2045 static int omap_hsmmc_suspend(struct device *dev) 2046 { 2047 struct omap_hsmmc_host *host = dev_get_drvdata(dev); 2048 2049 if (!host) 2050 return 0; 2051 2052 pm_runtime_get_sync(host->dev); 2053 2054 if (!(host->mmc->pm_flags & MMC_PM_KEEP_POWER)) { 2055 OMAP_HSMMC_WRITE(host->base, ISE, 0); 2056 OMAP_HSMMC_WRITE(host->base, IE, 0); 2057 OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR); 2058 OMAP_HSMMC_WRITE(host->base, HCTL, 2059 OMAP_HSMMC_READ(host->base, HCTL) & ~SDBP); 2060 } 2061 2062 clk_disable_unprepare(host->dbclk); 2063 2064 pm_runtime_put_sync(host->dev); 2065 return 0; 2066 } 2067 2068 /* Routine to resume the MMC device */ 2069 static int omap_hsmmc_resume(struct device *dev) 2070 { 2071 struct omap_hsmmc_host *host = dev_get_drvdata(dev); 2072 2073 if (!host) 2074 return 0; 2075 2076 pm_runtime_get_sync(host->dev); 2077 2078 clk_prepare_enable(host->dbclk); 2079 2080 if (!(host->mmc->pm_flags & MMC_PM_KEEP_POWER)) 2081 omap_hsmmc_conf_bus_power(host); 2082 2083 pm_runtime_mark_last_busy(host->dev); 2084 pm_runtime_put_autosuspend(host->dev); 2085 return 0; 2086 } 2087 #endif 2088 2089 static int omap_hsmmc_runtime_suspend(struct device *dev) 2090 { 2091 struct omap_hsmmc_host *host; 2092 unsigned long flags; 2093 int ret = 0; 2094 2095 host = dev_get_drvdata(dev); 2096 omap_hsmmc_context_save(host); 2097 dev_dbg(dev, "disabled\n"); 2098 2099 spin_lock_irqsave(&host->irq_lock, flags); 2100 if ((host->mmc->caps & MMC_CAP_SDIO_IRQ) && 2101 (host->flags & HSMMC_SDIO_IRQ_ENABLED)) { 2102 /* disable sdio irq handling to prevent race */ 2103 OMAP_HSMMC_WRITE(host->base, ISE, 0); 2104 OMAP_HSMMC_WRITE(host->base, IE, 0); 2105 2106 if (!(OMAP_HSMMC_READ(host->base, PSTATE) & DLEV_DAT(1))) { 2107 /* 2108 * dat1 line low, pending sdio irq 2109 * race condition: possible irq handler running on 2110 * multi-core, abort 2111 */ 2112 dev_dbg(dev, "pending sdio irq, abort suspend\n"); 2113 OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR); 2114 OMAP_HSMMC_WRITE(host->base, ISE, CIRQ_EN); 2115 OMAP_HSMMC_WRITE(host->base, IE, CIRQ_EN); 2116 pm_runtime_mark_last_busy(dev); 2117 ret = -EBUSY; 2118 goto abort; 2119 } 2120 2121 pinctrl_pm_select_idle_state(dev); 2122 } else { 2123 pinctrl_pm_select_idle_state(dev); 2124 } 2125 2126 abort: 2127 spin_unlock_irqrestore(&host->irq_lock, flags); 2128 return ret; 2129 } 2130 2131 static int omap_hsmmc_runtime_resume(struct device *dev) 2132 { 2133 struct omap_hsmmc_host *host; 2134 unsigned long flags; 2135 2136 host = dev_get_drvdata(dev); 2137 omap_hsmmc_context_restore(host); 2138 dev_dbg(dev, "enabled\n"); 2139 2140 spin_lock_irqsave(&host->irq_lock, flags); 2141 if ((host->mmc->caps & MMC_CAP_SDIO_IRQ) && 2142 (host->flags & HSMMC_SDIO_IRQ_ENABLED)) { 2143 2144 pinctrl_select_default_state(host->dev); 2145 2146 /* irq lost, if pinmux incorrect */ 2147 OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR); 2148 OMAP_HSMMC_WRITE(host->base, ISE, CIRQ_EN); 2149 OMAP_HSMMC_WRITE(host->base, IE, CIRQ_EN); 2150 } else { 2151 pinctrl_select_default_state(host->dev); 2152 } 2153 spin_unlock_irqrestore(&host->irq_lock, flags); 2154 return 0; 2155 } 2156 2157 static const struct dev_pm_ops omap_hsmmc_dev_pm_ops = { 2158 SET_SYSTEM_SLEEP_PM_OPS(omap_hsmmc_suspend, omap_hsmmc_resume) 2159 .runtime_suspend = omap_hsmmc_runtime_suspend, 2160 .runtime_resume = omap_hsmmc_runtime_resume, 2161 }; 2162 2163 static struct platform_driver omap_hsmmc_driver = { 2164 .probe = omap_hsmmc_probe, 2165 .remove = omap_hsmmc_remove, 2166 .driver = { 2167 .name = DRIVER_NAME, 2168 .probe_type = PROBE_PREFER_ASYNCHRONOUS, 2169 .pm = &omap_hsmmc_dev_pm_ops, 2170 .of_match_table = of_match_ptr(omap_mmc_of_match), 2171 }, 2172 }; 2173 2174 module_platform_driver(omap_hsmmc_driver); 2175 MODULE_DESCRIPTION("OMAP High Speed Multimedia Card driver"); 2176 MODULE_LICENSE("GPL"); 2177 MODULE_ALIAS("platform:" DRIVER_NAME); 2178 MODULE_AUTHOR("Texas Instruments Inc"); 2179