1menu "EEPROM support" 2 3config EEPROM_AT24 4 tristate "I2C EEPROMs / RAMs / ROMs from most vendors" 5 depends on I2C && SYSFS 6 help 7 Enable this driver to get read/write support to most I2C EEPROMs 8 and compatible devices like FRAMs, SRAMs, ROMs etc. After you 9 configure the driver to know about each chip on your target 10 board. Use these generic chip names, instead of vendor-specific 11 ones like at24c64, 24lc02 or fm24c04: 12 13 24c00, 24c01, 24c02, spd (readonly 24c02), 24c04, 24c08, 14 24c16, 24c32, 24c64, 24c128, 24c256, 24c512, 24c1024 15 16 Unless you like data loss puzzles, always be sure that any chip 17 you configure as a 24c32 (32 kbit) or larger is NOT really a 18 24c16 (16 kbit) or smaller, and vice versa. Marking the chip 19 as read-only won't help recover from this. Also, if your chip 20 has any software write-protect mechanism you may want to review the 21 code to make sure this driver won't turn it on by accident. 22 23 If you use this with an SMBus adapter instead of an I2C adapter, 24 full functionality is not available. Only smaller devices are 25 supported (24c16 and below, max 4 kByte). 26 27 This driver can also be built as a module. If so, the module 28 will be called at24. 29 30config EEPROM_AT25 31 tristate "SPI EEPROMs from most vendors" 32 depends on SPI && SYSFS 33 help 34 Enable this driver to get read/write support to most SPI EEPROMs, 35 after you configure the board init code to know about each eeprom 36 on your target board. 37 38 This driver can also be built as a module. If so, the module 39 will be called at25. 40 41config EEPROM_LEGACY 42 tristate "Old I2C EEPROM reader" 43 depends on I2C && SYSFS 44 help 45 If you say yes here you get read-only access to the EEPROM data 46 available on modern memory DIMMs and Sony Vaio laptops via I2C. Such 47 EEPROMs could theoretically be available on other devices as well. 48 49 This driver can also be built as a module. If so, the module 50 will be called eeprom. 51 52config EEPROM_MAX6875 53 tristate "Maxim MAX6874/5 power supply supervisor" 54 depends on I2C 55 help 56 If you say yes here you get read-only support for the user EEPROM of 57 the Maxim MAX6874/5 EEPROM-programmable, quad power-supply 58 sequencer/supervisor. 59 60 All other features of this chip should be accessed via i2c-dev. 61 62 This driver can also be built as a module. If so, the module 63 will be called max6875. 64 65 66config EEPROM_93CX6 67 tristate "EEPROM 93CX6 support" 68 help 69 This is a driver for the EEPROM chipsets 93c46 and 93c66. 70 The driver supports both read as well as write commands. 71 72 If unsure, say N. 73 74config EEPROM_93XX46 75 tristate "Microwire EEPROM 93XX46 support" 76 depends on SPI && SYSFS 77 help 78 Driver for the microwire EEPROM chipsets 93xx46x. The driver 79 supports both read and write commands and also the command to 80 erase the whole EEPROM. 81 82 This driver can also be built as a module. If so, the module 83 will be called eeprom_93xx46. 84 85 If unsure, say N. 86 87config EEPROM_DIGSY_MTC_CFG 88 bool "DigsyMTC display configuration EEPROMs device" 89 depends on GPIO_MPC5200 && SPI_GPIO 90 help 91 This option enables access to display configuration EEPROMs 92 on digsy_mtc board. You have to additionally select Microwire 93 EEPROM 93XX46 driver. sysfs entries will be created for that 94 EEPROM allowing to read/write the configuration data or to 95 erase the whole EEPROM. 96 97 If unsure, say N. 98 99endmenu 100