1 /* 2 * linux/drivers/mfd/ucb1x00-core.c 3 * 4 * Copyright (C) 2001 Russell King, All Rights Reserved. 5 * 6 * This program is free software; you can redistribute it and/or modify 7 * it under the terms of the GNU General Public License as published by 8 * the Free Software Foundation; either version 2 of the License. 9 * 10 * The UCB1x00 core driver provides basic services for handling IO, 11 * the ADC, interrupts, and accessing registers. It is designed 12 * such that everything goes through this layer, thereby providing 13 * a consistent locking methodology, as well as allowing the drivers 14 * to be used on other non-MCP-enabled hardware platforms. 15 * 16 * Note that all locks are private to this file. Nothing else may 17 * touch them. 18 */ 19 #include <linux/module.h> 20 #include <linux/kernel.h> 21 #include <linux/sched.h> 22 #include <linux/slab.h> 23 #include <linux/init.h> 24 #include <linux/errno.h> 25 #include <linux/interrupt.h> 26 #include <linux/device.h> 27 #include <linux/mutex.h> 28 29 #include <mach/dma.h> 30 #include <mach/hardware.h> 31 32 #include "ucb1x00.h" 33 34 static DEFINE_MUTEX(ucb1x00_mutex); 35 static LIST_HEAD(ucb1x00_drivers); 36 static LIST_HEAD(ucb1x00_devices); 37 38 /** 39 * ucb1x00_io_set_dir - set IO direction 40 * @ucb: UCB1x00 structure describing chip 41 * @in: bitfield of IO pins to be set as inputs 42 * @out: bitfield of IO pins to be set as outputs 43 * 44 * Set the IO direction of the ten general purpose IO pins on 45 * the UCB1x00 chip. The @in bitfield has priority over the 46 * @out bitfield, in that if you specify a pin as both input 47 * and output, it will end up as an input. 48 * 49 * ucb1x00_enable must have been called to enable the comms 50 * before using this function. 51 * 52 * This function takes a spinlock, disabling interrupts. 53 */ 54 void ucb1x00_io_set_dir(struct ucb1x00 *ucb, unsigned int in, unsigned int out) 55 { 56 unsigned long flags; 57 58 spin_lock_irqsave(&ucb->io_lock, flags); 59 ucb->io_dir |= out; 60 ucb->io_dir &= ~in; 61 62 ucb1x00_reg_write(ucb, UCB_IO_DIR, ucb->io_dir); 63 spin_unlock_irqrestore(&ucb->io_lock, flags); 64 } 65 66 /** 67 * ucb1x00_io_write - set or clear IO outputs 68 * @ucb: UCB1x00 structure describing chip 69 * @set: bitfield of IO pins to set to logic '1' 70 * @clear: bitfield of IO pins to set to logic '0' 71 * 72 * Set the IO output state of the specified IO pins. The value 73 * is retained if the pins are subsequently configured as inputs. 74 * The @clear bitfield has priority over the @set bitfield - 75 * outputs will be cleared. 76 * 77 * ucb1x00_enable must have been called to enable the comms 78 * before using this function. 79 * 80 * This function takes a spinlock, disabling interrupts. 81 */ 82 void ucb1x00_io_write(struct ucb1x00 *ucb, unsigned int set, unsigned int clear) 83 { 84 unsigned long flags; 85 86 spin_lock_irqsave(&ucb->io_lock, flags); 87 ucb->io_out |= set; 88 ucb->io_out &= ~clear; 89 90 ucb1x00_reg_write(ucb, UCB_IO_DATA, ucb->io_out); 91 spin_unlock_irqrestore(&ucb->io_lock, flags); 92 } 93 94 /** 95 * ucb1x00_io_read - read the current state of the IO pins 96 * @ucb: UCB1x00 structure describing chip 97 * 98 * Return a bitfield describing the logic state of the ten 99 * general purpose IO pins. 100 * 101 * ucb1x00_enable must have been called to enable the comms 102 * before using this function. 103 * 104 * This function does not take any semaphores or spinlocks. 105 */ 106 unsigned int ucb1x00_io_read(struct ucb1x00 *ucb) 107 { 108 return ucb1x00_reg_read(ucb, UCB_IO_DATA); 109 } 110 111 /* 112 * UCB1300 data sheet says we must: 113 * 1. enable ADC => 5us (including reference startup time) 114 * 2. select input => 51*tsibclk => 4.3us 115 * 3. start conversion => 102*tsibclk => 8.5us 116 * (tsibclk = 1/11981000) 117 * Period between SIB 128-bit frames = 10.7us 118 */ 119 120 /** 121 * ucb1x00_adc_enable - enable the ADC converter 122 * @ucb: UCB1x00 structure describing chip 123 * 124 * Enable the ucb1x00 and ADC converter on the UCB1x00 for use. 125 * Any code wishing to use the ADC converter must call this 126 * function prior to using it. 127 * 128 * This function takes the ADC semaphore to prevent two or more 129 * concurrent uses, and therefore may sleep. As a result, it 130 * can only be called from process context, not interrupt 131 * context. 132 * 133 * You should release the ADC as soon as possible using 134 * ucb1x00_adc_disable. 135 */ 136 void ucb1x00_adc_enable(struct ucb1x00 *ucb) 137 { 138 down(&ucb->adc_sem); 139 140 ucb->adc_cr |= UCB_ADC_ENA; 141 142 ucb1x00_enable(ucb); 143 ucb1x00_reg_write(ucb, UCB_ADC_CR, ucb->adc_cr); 144 } 145 146 /** 147 * ucb1x00_adc_read - read the specified ADC channel 148 * @ucb: UCB1x00 structure describing chip 149 * @adc_channel: ADC channel mask 150 * @sync: wait for syncronisation pulse. 151 * 152 * Start an ADC conversion and wait for the result. Note that 153 * synchronised ADC conversions (via the ADCSYNC pin) must wait 154 * until the trigger is asserted and the conversion is finished. 155 * 156 * This function currently spins waiting for the conversion to 157 * complete (2 frames max without sync). 158 * 159 * If called for a synchronised ADC conversion, it may sleep 160 * with the ADC semaphore held. 161 */ 162 unsigned int ucb1x00_adc_read(struct ucb1x00 *ucb, int adc_channel, int sync) 163 { 164 unsigned int val; 165 166 if (sync) 167 adc_channel |= UCB_ADC_SYNC_ENA; 168 169 ucb1x00_reg_write(ucb, UCB_ADC_CR, ucb->adc_cr | adc_channel); 170 ucb1x00_reg_write(ucb, UCB_ADC_CR, ucb->adc_cr | adc_channel | UCB_ADC_START); 171 172 for (;;) { 173 val = ucb1x00_reg_read(ucb, UCB_ADC_DATA); 174 if (val & UCB_ADC_DAT_VAL) 175 break; 176 /* yield to other processes */ 177 set_current_state(TASK_INTERRUPTIBLE); 178 schedule_timeout(1); 179 } 180 181 return UCB_ADC_DAT(val); 182 } 183 184 /** 185 * ucb1x00_adc_disable - disable the ADC converter 186 * @ucb: UCB1x00 structure describing chip 187 * 188 * Disable the ADC converter and release the ADC semaphore. 189 */ 190 void ucb1x00_adc_disable(struct ucb1x00 *ucb) 191 { 192 ucb->adc_cr &= ~UCB_ADC_ENA; 193 ucb1x00_reg_write(ucb, UCB_ADC_CR, ucb->adc_cr); 194 ucb1x00_disable(ucb); 195 196 up(&ucb->adc_sem); 197 } 198 199 /* 200 * UCB1x00 Interrupt handling. 201 * 202 * The UCB1x00 can generate interrupts when the SIBCLK is stopped. 203 * Since we need to read an internal register, we must re-enable 204 * SIBCLK to talk to the chip. We leave the clock running until 205 * we have finished processing all interrupts from the chip. 206 */ 207 static irqreturn_t ucb1x00_irq(int irqnr, void *devid) 208 { 209 struct ucb1x00 *ucb = devid; 210 struct ucb1x00_irq *irq; 211 unsigned int isr, i; 212 213 ucb1x00_enable(ucb); 214 isr = ucb1x00_reg_read(ucb, UCB_IE_STATUS); 215 ucb1x00_reg_write(ucb, UCB_IE_CLEAR, isr); 216 ucb1x00_reg_write(ucb, UCB_IE_CLEAR, 0); 217 218 for (i = 0, irq = ucb->irq_handler; i < 16 && isr; i++, isr >>= 1, irq++) 219 if (isr & 1 && irq->fn) 220 irq->fn(i, irq->devid); 221 ucb1x00_disable(ucb); 222 223 return IRQ_HANDLED; 224 } 225 226 /** 227 * ucb1x00_hook_irq - hook a UCB1x00 interrupt 228 * @ucb: UCB1x00 structure describing chip 229 * @idx: interrupt index 230 * @fn: function to call when interrupt is triggered 231 * @devid: device id to pass to interrupt handler 232 * 233 * Hook the specified interrupt. You can only register one handler 234 * for each interrupt source. The interrupt source is not enabled 235 * by this function; use ucb1x00_enable_irq instead. 236 * 237 * Interrupt handlers will be called with other interrupts enabled. 238 * 239 * Returns zero on success, or one of the following errors: 240 * -EINVAL if the interrupt index is invalid 241 * -EBUSY if the interrupt has already been hooked 242 */ 243 int ucb1x00_hook_irq(struct ucb1x00 *ucb, unsigned int idx, void (*fn)(int, void *), void *devid) 244 { 245 struct ucb1x00_irq *irq; 246 int ret = -EINVAL; 247 248 if (idx < 16) { 249 irq = ucb->irq_handler + idx; 250 ret = -EBUSY; 251 252 spin_lock_irq(&ucb->lock); 253 if (irq->fn == NULL) { 254 irq->devid = devid; 255 irq->fn = fn; 256 ret = 0; 257 } 258 spin_unlock_irq(&ucb->lock); 259 } 260 return ret; 261 } 262 263 /** 264 * ucb1x00_enable_irq - enable an UCB1x00 interrupt source 265 * @ucb: UCB1x00 structure describing chip 266 * @idx: interrupt index 267 * @edges: interrupt edges to enable 268 * 269 * Enable the specified interrupt to trigger on %UCB_RISING, 270 * %UCB_FALLING or both edges. The interrupt should have been 271 * hooked by ucb1x00_hook_irq. 272 */ 273 void ucb1x00_enable_irq(struct ucb1x00 *ucb, unsigned int idx, int edges) 274 { 275 unsigned long flags; 276 277 if (idx < 16) { 278 spin_lock_irqsave(&ucb->lock, flags); 279 280 ucb1x00_enable(ucb); 281 if (edges & UCB_RISING) { 282 ucb->irq_ris_enbl |= 1 << idx; 283 ucb1x00_reg_write(ucb, UCB_IE_RIS, ucb->irq_ris_enbl); 284 } 285 if (edges & UCB_FALLING) { 286 ucb->irq_fal_enbl |= 1 << idx; 287 ucb1x00_reg_write(ucb, UCB_IE_FAL, ucb->irq_fal_enbl); 288 } 289 ucb1x00_disable(ucb); 290 spin_unlock_irqrestore(&ucb->lock, flags); 291 } 292 } 293 294 /** 295 * ucb1x00_disable_irq - disable an UCB1x00 interrupt source 296 * @ucb: UCB1x00 structure describing chip 297 * @edges: interrupt edges to disable 298 * 299 * Disable the specified interrupt triggering on the specified 300 * (%UCB_RISING, %UCB_FALLING or both) edges. 301 */ 302 void ucb1x00_disable_irq(struct ucb1x00 *ucb, unsigned int idx, int edges) 303 { 304 unsigned long flags; 305 306 if (idx < 16) { 307 spin_lock_irqsave(&ucb->lock, flags); 308 309 ucb1x00_enable(ucb); 310 if (edges & UCB_RISING) { 311 ucb->irq_ris_enbl &= ~(1 << idx); 312 ucb1x00_reg_write(ucb, UCB_IE_RIS, ucb->irq_ris_enbl); 313 } 314 if (edges & UCB_FALLING) { 315 ucb->irq_fal_enbl &= ~(1 << idx); 316 ucb1x00_reg_write(ucb, UCB_IE_FAL, ucb->irq_fal_enbl); 317 } 318 ucb1x00_disable(ucb); 319 spin_unlock_irqrestore(&ucb->lock, flags); 320 } 321 } 322 323 /** 324 * ucb1x00_free_irq - disable and free the specified UCB1x00 interrupt 325 * @ucb: UCB1x00 structure describing chip 326 * @idx: interrupt index 327 * @devid: device id. 328 * 329 * Disable the interrupt source and remove the handler. devid must 330 * match the devid passed when hooking the interrupt. 331 * 332 * Returns zero on success, or one of the following errors: 333 * -EINVAL if the interrupt index is invalid 334 * -ENOENT if devid does not match 335 */ 336 int ucb1x00_free_irq(struct ucb1x00 *ucb, unsigned int idx, void *devid) 337 { 338 struct ucb1x00_irq *irq; 339 int ret; 340 341 if (idx >= 16) 342 goto bad; 343 344 irq = ucb->irq_handler + idx; 345 ret = -ENOENT; 346 347 spin_lock_irq(&ucb->lock); 348 if (irq->devid == devid) { 349 ucb->irq_ris_enbl &= ~(1 << idx); 350 ucb->irq_fal_enbl &= ~(1 << idx); 351 352 ucb1x00_enable(ucb); 353 ucb1x00_reg_write(ucb, UCB_IE_RIS, ucb->irq_ris_enbl); 354 ucb1x00_reg_write(ucb, UCB_IE_FAL, ucb->irq_fal_enbl); 355 ucb1x00_disable(ucb); 356 357 irq->fn = NULL; 358 irq->devid = NULL; 359 ret = 0; 360 } 361 spin_unlock_irq(&ucb->lock); 362 return ret; 363 364 bad: 365 printk(KERN_ERR "Freeing bad UCB1x00 irq %d\n", idx); 366 return -EINVAL; 367 } 368 369 static int ucb1x00_add_dev(struct ucb1x00 *ucb, struct ucb1x00_driver *drv) 370 { 371 struct ucb1x00_dev *dev; 372 int ret = -ENOMEM; 373 374 dev = kmalloc(sizeof(struct ucb1x00_dev), GFP_KERNEL); 375 if (dev) { 376 dev->ucb = ucb; 377 dev->drv = drv; 378 379 ret = drv->add(dev); 380 381 if (ret == 0) { 382 list_add(&dev->dev_node, &ucb->devs); 383 list_add(&dev->drv_node, &drv->devs); 384 } else { 385 kfree(dev); 386 } 387 } 388 return ret; 389 } 390 391 static void ucb1x00_remove_dev(struct ucb1x00_dev *dev) 392 { 393 dev->drv->remove(dev); 394 list_del(&dev->dev_node); 395 list_del(&dev->drv_node); 396 kfree(dev); 397 } 398 399 /* 400 * Try to probe our interrupt, rather than relying on lots of 401 * hard-coded machine dependencies. For reference, the expected 402 * IRQ mappings are: 403 * 404 * Machine Default IRQ 405 * adsbitsy IRQ_GPCIN4 406 * cerf IRQ_GPIO_UCB1200_IRQ 407 * flexanet IRQ_GPIO_GUI 408 * freebird IRQ_GPIO_FREEBIRD_UCB1300_IRQ 409 * graphicsclient ADS_EXT_IRQ(8) 410 * graphicsmaster ADS_EXT_IRQ(8) 411 * lart LART_IRQ_UCB1200 412 * omnimeter IRQ_GPIO23 413 * pfs168 IRQ_GPIO_UCB1300_IRQ 414 * simpad IRQ_GPIO_UCB1300_IRQ 415 * shannon SHANNON_IRQ_GPIO_IRQ_CODEC 416 * yopy IRQ_GPIO_UCB1200_IRQ 417 */ 418 static int ucb1x00_detect_irq(struct ucb1x00 *ucb) 419 { 420 unsigned long mask; 421 422 mask = probe_irq_on(); 423 if (!mask) { 424 probe_irq_off(mask); 425 return NO_IRQ; 426 } 427 428 /* 429 * Enable the ADC interrupt. 430 */ 431 ucb1x00_reg_write(ucb, UCB_IE_RIS, UCB_IE_ADC); 432 ucb1x00_reg_write(ucb, UCB_IE_FAL, UCB_IE_ADC); 433 ucb1x00_reg_write(ucb, UCB_IE_CLEAR, 0xffff); 434 ucb1x00_reg_write(ucb, UCB_IE_CLEAR, 0); 435 436 /* 437 * Cause an ADC interrupt. 438 */ 439 ucb1x00_reg_write(ucb, UCB_ADC_CR, UCB_ADC_ENA); 440 ucb1x00_reg_write(ucb, UCB_ADC_CR, UCB_ADC_ENA | UCB_ADC_START); 441 442 /* 443 * Wait for the conversion to complete. 444 */ 445 while ((ucb1x00_reg_read(ucb, UCB_ADC_DATA) & UCB_ADC_DAT_VAL) == 0); 446 ucb1x00_reg_write(ucb, UCB_ADC_CR, 0); 447 448 /* 449 * Disable and clear interrupt. 450 */ 451 ucb1x00_reg_write(ucb, UCB_IE_RIS, 0); 452 ucb1x00_reg_write(ucb, UCB_IE_FAL, 0); 453 ucb1x00_reg_write(ucb, UCB_IE_CLEAR, 0xffff); 454 ucb1x00_reg_write(ucb, UCB_IE_CLEAR, 0); 455 456 /* 457 * Read triggered interrupt. 458 */ 459 return probe_irq_off(mask); 460 } 461 462 static void ucb1x00_release(struct device *dev) 463 { 464 struct ucb1x00 *ucb = classdev_to_ucb1x00(dev); 465 kfree(ucb); 466 } 467 468 static struct class ucb1x00_class = { 469 .name = "ucb1x00", 470 .dev_release = ucb1x00_release, 471 }; 472 473 static int ucb1x00_probe(struct mcp *mcp) 474 { 475 struct ucb1x00 *ucb; 476 struct ucb1x00_driver *drv; 477 unsigned int id; 478 int ret = -ENODEV; 479 480 mcp_enable(mcp); 481 id = mcp_reg_read(mcp, UCB_ID); 482 483 if (id != UCB_ID_1200 && id != UCB_ID_1300 && id != UCB_ID_TC35143) { 484 printk(KERN_WARNING "UCB1x00 ID not found: %04x\n", id); 485 goto err_disable; 486 } 487 488 ucb = kzalloc(sizeof(struct ucb1x00), GFP_KERNEL); 489 ret = -ENOMEM; 490 if (!ucb) 491 goto err_disable; 492 493 494 ucb->dev.class = &ucb1x00_class; 495 ucb->dev.parent = &mcp->attached_device; 496 dev_set_name(&ucb->dev, "ucb1x00"); 497 498 spin_lock_init(&ucb->lock); 499 spin_lock_init(&ucb->io_lock); 500 sema_init(&ucb->adc_sem, 1); 501 502 ucb->id = id; 503 ucb->mcp = mcp; 504 ucb->irq = ucb1x00_detect_irq(ucb); 505 if (ucb->irq == NO_IRQ) { 506 printk(KERN_ERR "UCB1x00: IRQ probe failed\n"); 507 ret = -ENODEV; 508 goto err_free; 509 } 510 511 ret = request_irq(ucb->irq, ucb1x00_irq, IRQF_TRIGGER_RISING, 512 "UCB1x00", ucb); 513 if (ret) { 514 printk(KERN_ERR "ucb1x00: unable to grab irq%d: %d\n", 515 ucb->irq, ret); 516 goto err_free; 517 } 518 519 mcp_set_drvdata(mcp, ucb); 520 521 ret = device_register(&ucb->dev); 522 if (ret) 523 goto err_irq; 524 525 INIT_LIST_HEAD(&ucb->devs); 526 mutex_lock(&ucb1x00_mutex); 527 list_add(&ucb->node, &ucb1x00_devices); 528 list_for_each_entry(drv, &ucb1x00_drivers, node) { 529 ucb1x00_add_dev(ucb, drv); 530 } 531 mutex_unlock(&ucb1x00_mutex); 532 goto out; 533 534 err_irq: 535 free_irq(ucb->irq, ucb); 536 err_free: 537 kfree(ucb); 538 err_disable: 539 mcp_disable(mcp); 540 out: 541 return ret; 542 } 543 544 static void ucb1x00_remove(struct mcp *mcp) 545 { 546 struct ucb1x00 *ucb = mcp_get_drvdata(mcp); 547 struct list_head *l, *n; 548 549 mutex_lock(&ucb1x00_mutex); 550 list_del(&ucb->node); 551 list_for_each_safe(l, n, &ucb->devs) { 552 struct ucb1x00_dev *dev = list_entry(l, struct ucb1x00_dev, dev_node); 553 ucb1x00_remove_dev(dev); 554 } 555 mutex_unlock(&ucb1x00_mutex); 556 557 free_irq(ucb->irq, ucb); 558 device_unregister(&ucb->dev); 559 } 560 561 int ucb1x00_register_driver(struct ucb1x00_driver *drv) 562 { 563 struct ucb1x00 *ucb; 564 565 INIT_LIST_HEAD(&drv->devs); 566 mutex_lock(&ucb1x00_mutex); 567 list_add(&drv->node, &ucb1x00_drivers); 568 list_for_each_entry(ucb, &ucb1x00_devices, node) { 569 ucb1x00_add_dev(ucb, drv); 570 } 571 mutex_unlock(&ucb1x00_mutex); 572 return 0; 573 } 574 575 void ucb1x00_unregister_driver(struct ucb1x00_driver *drv) 576 { 577 struct list_head *n, *l; 578 579 mutex_lock(&ucb1x00_mutex); 580 list_del(&drv->node); 581 list_for_each_safe(l, n, &drv->devs) { 582 struct ucb1x00_dev *dev = list_entry(l, struct ucb1x00_dev, drv_node); 583 ucb1x00_remove_dev(dev); 584 } 585 mutex_unlock(&ucb1x00_mutex); 586 } 587 588 static int ucb1x00_suspend(struct mcp *mcp, pm_message_t state) 589 { 590 struct ucb1x00 *ucb = mcp_get_drvdata(mcp); 591 struct ucb1x00_dev *dev; 592 593 mutex_lock(&ucb1x00_mutex); 594 list_for_each_entry(dev, &ucb->devs, dev_node) { 595 if (dev->drv->suspend) 596 dev->drv->suspend(dev, state); 597 } 598 mutex_unlock(&ucb1x00_mutex); 599 return 0; 600 } 601 602 static int ucb1x00_resume(struct mcp *mcp) 603 { 604 struct ucb1x00 *ucb = mcp_get_drvdata(mcp); 605 struct ucb1x00_dev *dev; 606 607 mutex_lock(&ucb1x00_mutex); 608 list_for_each_entry(dev, &ucb->devs, dev_node) { 609 if (dev->drv->resume) 610 dev->drv->resume(dev); 611 } 612 mutex_unlock(&ucb1x00_mutex); 613 return 0; 614 } 615 616 static struct mcp_driver ucb1x00_driver = { 617 .drv = { 618 .name = "ucb1x00", 619 }, 620 .probe = ucb1x00_probe, 621 .remove = ucb1x00_remove, 622 .suspend = ucb1x00_suspend, 623 .resume = ucb1x00_resume, 624 }; 625 626 static int __init ucb1x00_init(void) 627 { 628 int ret = class_register(&ucb1x00_class); 629 if (ret == 0) { 630 ret = mcp_driver_register(&ucb1x00_driver); 631 if (ret) 632 class_unregister(&ucb1x00_class); 633 } 634 return ret; 635 } 636 637 static void __exit ucb1x00_exit(void) 638 { 639 mcp_driver_unregister(&ucb1x00_driver); 640 class_unregister(&ucb1x00_class); 641 } 642 643 module_init(ucb1x00_init); 644 module_exit(ucb1x00_exit); 645 646 EXPORT_SYMBOL(ucb1x00_io_set_dir); 647 EXPORT_SYMBOL(ucb1x00_io_write); 648 EXPORT_SYMBOL(ucb1x00_io_read); 649 650 EXPORT_SYMBOL(ucb1x00_adc_enable); 651 EXPORT_SYMBOL(ucb1x00_adc_read); 652 EXPORT_SYMBOL(ucb1x00_adc_disable); 653 654 EXPORT_SYMBOL(ucb1x00_hook_irq); 655 EXPORT_SYMBOL(ucb1x00_free_irq); 656 EXPORT_SYMBOL(ucb1x00_enable_irq); 657 EXPORT_SYMBOL(ucb1x00_disable_irq); 658 659 EXPORT_SYMBOL(ucb1x00_register_driver); 660 EXPORT_SYMBOL(ucb1x00_unregister_driver); 661 662 MODULE_AUTHOR("Russell King <rmk@arm.linux.org.uk>"); 663 MODULE_DESCRIPTION("UCB1x00 core driver"); 664 MODULE_LICENSE("GPL"); 665