1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * tps65010 - driver for tps6501x power management chips 4 * 5 * Copyright (C) 2004 Texas Instruments 6 * Copyright (C) 2004-2005 David Brownell 7 */ 8 9 #include <linux/kernel.h> 10 #include <linux/module.h> 11 #include <linux/init.h> 12 #include <linux/slab.h> 13 #include <linux/interrupt.h> 14 #include <linux/i2c.h> 15 #include <linux/delay.h> 16 #include <linux/workqueue.h> 17 #include <linux/debugfs.h> 18 #include <linux/seq_file.h> 19 #include <linux/mutex.h> 20 #include <linux/platform_device.h> 21 22 #include <linux/mfd/tps65010.h> 23 24 #include <linux/gpio/driver.h> 25 26 27 /*-------------------------------------------------------------------------*/ 28 29 #define DRIVER_VERSION "2 May 2005" 30 #define DRIVER_NAME (tps65010_driver.driver.name) 31 32 MODULE_DESCRIPTION("TPS6501x Power Management Driver"); 33 MODULE_LICENSE("GPL"); 34 35 static struct i2c_driver tps65010_driver; 36 37 /*-------------------------------------------------------------------------*/ 38 39 /* This driver handles a family of multipurpose chips, which incorporate 40 * voltage regulators, lithium ion/polymer battery charging, GPIOs, LEDs, 41 * and other features often needed in portable devices like cell phones 42 * or digital cameras. 43 * 44 * The tps65011 and tps65013 have different voltage settings compared 45 * to tps65010 and tps65012. The tps65013 has a NO_CHG status/irq. 46 * All except tps65010 have "wait" mode, possibly defaulted so that 47 * battery-insert != device-on. 48 * 49 * We could distinguish between some models by checking VDCDC1.UVLO or 50 * other registers, unless they've been changed already after powerup 51 * as part of board setup by a bootloader. 52 */ 53 enum tps_model { 54 TPS65010, 55 TPS65011, 56 TPS65012, 57 TPS65013, 58 }; 59 60 struct tps65010 { 61 struct i2c_client *client; 62 struct mutex lock; 63 struct delayed_work work; 64 struct dentry *file; 65 unsigned charging:1; 66 unsigned por:1; 67 unsigned model:8; 68 u16 vbus; 69 unsigned long flags; 70 #define FLAG_VBUS_CHANGED 0 71 #define FLAG_IRQ_ENABLE 1 72 73 /* copies of last register state */ 74 u8 chgstatus, regstatus, chgconf; 75 u8 nmask1, nmask2; 76 77 u8 outmask; 78 struct gpio_chip chip; 79 struct platform_device *leds; 80 }; 81 82 #define POWER_POLL_DELAY msecs_to_jiffies(5000) 83 84 /*-------------------------------------------------------------------------*/ 85 86 #if defined(DEBUG) || defined(CONFIG_DEBUG_FS) 87 88 static void dbg_chgstat(char *buf, size_t len, u8 chgstatus) 89 { 90 snprintf(buf, len, "%02x%s%s%s%s%s%s%s%s\n", 91 chgstatus, 92 (chgstatus & TPS_CHG_USB) ? " USB" : "", 93 (chgstatus & TPS_CHG_AC) ? " AC" : "", 94 (chgstatus & TPS_CHG_THERM) ? " therm" : "", 95 (chgstatus & TPS_CHG_TERM) ? " done" : 96 ((chgstatus & (TPS_CHG_USB|TPS_CHG_AC)) 97 ? " (charging)" : ""), 98 (chgstatus & TPS_CHG_TAPER_TMO) ? " taper_tmo" : "", 99 (chgstatus & TPS_CHG_CHG_TMO) ? " charge_tmo" : "", 100 (chgstatus & TPS_CHG_PRECHG_TMO) ? " prechg_tmo" : "", 101 (chgstatus & TPS_CHG_TEMP_ERR) ? " temp_err" : ""); 102 } 103 104 static void dbg_regstat(char *buf, size_t len, u8 regstatus) 105 { 106 snprintf(buf, len, "%02x %s%s%s%s%s%s%s%s\n", 107 regstatus, 108 (regstatus & TPS_REG_ONOFF) ? "off" : "(on)", 109 (regstatus & TPS_REG_COVER) ? " uncover" : "", 110 (regstatus & TPS_REG_UVLO) ? " UVLO" : "", 111 (regstatus & TPS_REG_NO_CHG) ? " NO_CHG" : "", 112 (regstatus & TPS_REG_PG_LD02) ? " ld02_bad" : "", 113 (regstatus & TPS_REG_PG_LD01) ? " ld01_bad" : "", 114 (regstatus & TPS_REG_PG_MAIN) ? " main_bad" : "", 115 (regstatus & TPS_REG_PG_CORE) ? " core_bad" : ""); 116 } 117 118 static void dbg_chgconf(int por, char *buf, size_t len, u8 chgconfig) 119 { 120 const char *hibit; 121 122 if (por) 123 hibit = (chgconfig & TPS_CHARGE_POR) 124 ? "POR=69ms" : "POR=1sec"; 125 else 126 hibit = (chgconfig & TPS65013_AUA) ? "AUA" : ""; 127 128 snprintf(buf, len, "%02x %s%s%s AC=%d%% USB=%dmA %sCharge\n", 129 chgconfig, hibit, 130 (chgconfig & TPS_CHARGE_RESET) ? " reset" : "", 131 (chgconfig & TPS_CHARGE_FAST) ? " fast" : "", 132 ({int p; switch ((chgconfig >> 3) & 3) { 133 case 3: p = 100; break; 134 case 2: p = 75; break; 135 case 1: p = 50; break; 136 default: p = 25; break; 137 }; p; }), 138 (chgconfig & TPS_VBUS_CHARGING) 139 ? ((chgconfig & TPS_VBUS_500MA) ? 500 : 100) 140 : 0, 141 (chgconfig & TPS_CHARGE_ENABLE) ? "" : "No"); 142 } 143 144 #endif 145 146 #ifdef DEBUG 147 148 static void show_chgstatus(const char *label, u8 chgstatus) 149 { 150 char buf [100]; 151 152 dbg_chgstat(buf, sizeof buf, chgstatus); 153 pr_debug("%s: %s %s", DRIVER_NAME, label, buf); 154 } 155 156 static void show_regstatus(const char *label, u8 regstatus) 157 { 158 char buf [100]; 159 160 dbg_regstat(buf, sizeof buf, regstatus); 161 pr_debug("%s: %s %s", DRIVER_NAME, label, buf); 162 } 163 164 static void show_chgconfig(int por, const char *label, u8 chgconfig) 165 { 166 char buf [100]; 167 168 dbg_chgconf(por, buf, sizeof buf, chgconfig); 169 pr_debug("%s: %s %s", DRIVER_NAME, label, buf); 170 } 171 172 #else 173 174 static inline void show_chgstatus(const char *label, u8 chgstatus) { } 175 static inline void show_regstatus(const char *label, u8 chgstatus) { } 176 static inline void show_chgconfig(int por, const char *label, u8 chgconfig) { } 177 178 #endif 179 180 #ifdef CONFIG_DEBUG_FS 181 182 static int dbg_show(struct seq_file *s, void *_) 183 { 184 struct tps65010 *tps = s->private; 185 u8 value, v2; 186 unsigned i; 187 char buf[100]; 188 const char *chip; 189 190 switch (tps->model) { 191 case TPS65010: chip = "tps65010"; break; 192 case TPS65011: chip = "tps65011"; break; 193 case TPS65012: chip = "tps65012"; break; 194 case TPS65013: chip = "tps65013"; break; 195 default: chip = NULL; break; 196 } 197 seq_printf(s, "driver %s\nversion %s\nchip %s\n\n", 198 DRIVER_NAME, DRIVER_VERSION, chip); 199 200 mutex_lock(&tps->lock); 201 202 /* FIXME how can we tell whether a battery is present? 203 * likely involves a charge gauging chip (like BQ26501). 204 */ 205 206 seq_printf(s, "%scharging\n\n", tps->charging ? "" : "(not) "); 207 208 209 /* registers for monitoring battery charging and status; note 210 * that reading chgstat and regstat may ack IRQs... 211 */ 212 value = i2c_smbus_read_byte_data(tps->client, TPS_CHGCONFIG); 213 dbg_chgconf(tps->por, buf, sizeof buf, value); 214 seq_printf(s, "chgconfig %s", buf); 215 216 value = i2c_smbus_read_byte_data(tps->client, TPS_CHGSTATUS); 217 dbg_chgstat(buf, sizeof buf, value); 218 seq_printf(s, "chgstat %s", buf); 219 value = i2c_smbus_read_byte_data(tps->client, TPS_MASK1); 220 dbg_chgstat(buf, sizeof buf, value); 221 seq_printf(s, "mask1 %s", buf); 222 /* ignore ackint1 */ 223 224 value = i2c_smbus_read_byte_data(tps->client, TPS_REGSTATUS); 225 dbg_regstat(buf, sizeof buf, value); 226 seq_printf(s, "regstat %s", buf); 227 value = i2c_smbus_read_byte_data(tps->client, TPS_MASK2); 228 dbg_regstat(buf, sizeof buf, value); 229 seq_printf(s, "mask2 %s\n", buf); 230 /* ignore ackint2 */ 231 232 queue_delayed_work(system_power_efficient_wq, &tps->work, 233 POWER_POLL_DELAY); 234 235 /* VMAIN voltage, enable lowpower, etc */ 236 value = i2c_smbus_read_byte_data(tps->client, TPS_VDCDC1); 237 seq_printf(s, "vdcdc1 %02x\n", value); 238 239 /* VCORE voltage, vibrator on/off */ 240 value = i2c_smbus_read_byte_data(tps->client, TPS_VDCDC2); 241 seq_printf(s, "vdcdc2 %02x\n", value); 242 243 /* both LD0s, and their lowpower behavior */ 244 value = i2c_smbus_read_byte_data(tps->client, TPS_VREGS1); 245 seq_printf(s, "vregs1 %02x\n\n", value); 246 247 248 /* LEDs and GPIOs */ 249 value = i2c_smbus_read_byte_data(tps->client, TPS_LED1_ON); 250 v2 = i2c_smbus_read_byte_data(tps->client, TPS_LED1_PER); 251 seq_printf(s, "led1 %s, on=%02x, per=%02x, %d/%d msec\n", 252 (value & 0x80) 253 ? ((v2 & 0x80) ? "on" : "off") 254 : ((v2 & 0x80) ? "blink" : "(nPG)"), 255 value, v2, 256 (value & 0x7f) * 10, (v2 & 0x7f) * 100); 257 258 value = i2c_smbus_read_byte_data(tps->client, TPS_LED2_ON); 259 v2 = i2c_smbus_read_byte_data(tps->client, TPS_LED2_PER); 260 seq_printf(s, "led2 %s, on=%02x, per=%02x, %d/%d msec\n", 261 (value & 0x80) 262 ? ((v2 & 0x80) ? "on" : "off") 263 : ((v2 & 0x80) ? "blink" : "off"), 264 value, v2, 265 (value & 0x7f) * 10, (v2 & 0x7f) * 100); 266 267 value = i2c_smbus_read_byte_data(tps->client, TPS_DEFGPIO); 268 v2 = i2c_smbus_read_byte_data(tps->client, TPS_MASK3); 269 seq_printf(s, "defgpio %02x mask3 %02x\n", value, v2); 270 271 for (i = 0; i < 4; i++) { 272 if (value & (1 << (4 + i))) 273 seq_printf(s, " gpio%d-out %s\n", i + 1, 274 (value & (1 << i)) ? "low" : "hi "); 275 else 276 seq_printf(s, " gpio%d-in %s %s %s\n", i + 1, 277 (value & (1 << i)) ? "hi " : "low", 278 (v2 & (1 << i)) ? "no-irq" : "irq", 279 (v2 & (1 << (4 + i))) ? "rising" : "falling"); 280 } 281 282 mutex_unlock(&tps->lock); 283 return 0; 284 } 285 286 static int dbg_tps_open(struct inode *inode, struct file *file) 287 { 288 return single_open(file, dbg_show, inode->i_private); 289 } 290 291 static const struct file_operations debug_fops = { 292 .open = dbg_tps_open, 293 .read = seq_read, 294 .llseek = seq_lseek, 295 .release = single_release, 296 }; 297 298 #define DEBUG_FOPS &debug_fops 299 300 #else 301 #define DEBUG_FOPS NULL 302 #endif 303 304 /*-------------------------------------------------------------------------*/ 305 306 /* handle IRQS in a task context, so we can use I2C calls */ 307 static void tps65010_interrupt(struct tps65010 *tps) 308 { 309 u8 tmp = 0, mask, poll; 310 311 /* IRQs won't trigger for certain events, but we can get 312 * others by polling (normally, with external power applied). 313 */ 314 poll = 0; 315 316 /* regstatus irqs */ 317 if (tps->nmask2) { 318 tmp = i2c_smbus_read_byte_data(tps->client, TPS_REGSTATUS); 319 mask = tmp ^ tps->regstatus; 320 tps->regstatus = tmp; 321 mask &= tps->nmask2; 322 } else 323 mask = 0; 324 if (mask) { 325 tps->regstatus = tmp; 326 /* may need to shut something down ... */ 327 328 /* "off" usually means deep sleep */ 329 if (tmp & TPS_REG_ONOFF) { 330 pr_info("%s: power off button\n", DRIVER_NAME); 331 #if 0 332 /* REVISIT: this might need its own workqueue 333 * plus tweaks including deadlock avoidance ... 334 * also needs to get error handling and probably 335 * an #ifdef CONFIG_HIBERNATION 336 */ 337 hibernate(); 338 #endif 339 poll = 1; 340 } 341 } 342 343 /* chgstatus irqs */ 344 if (tps->nmask1) { 345 tmp = i2c_smbus_read_byte_data(tps->client, TPS_CHGSTATUS); 346 mask = tmp ^ tps->chgstatus; 347 tps->chgstatus = tmp; 348 mask &= tps->nmask1; 349 } else 350 mask = 0; 351 if (mask) { 352 unsigned charging = 0; 353 354 show_chgstatus("chg/irq", tmp); 355 if (tmp & (TPS_CHG_USB|TPS_CHG_AC)) 356 show_chgconfig(tps->por, "conf", tps->chgconf); 357 358 /* Unless it was turned off or disabled, we charge any 359 * battery whenever there's power available for it 360 * and the charger hasn't been disabled. 361 */ 362 if (!(tps->chgstatus & ~(TPS_CHG_USB|TPS_CHG_AC)) 363 && (tps->chgstatus & (TPS_CHG_USB|TPS_CHG_AC)) 364 && (tps->chgconf & TPS_CHARGE_ENABLE) 365 ) { 366 if (tps->chgstatus & TPS_CHG_USB) { 367 /* VBUS options are readonly until reconnect */ 368 if (mask & TPS_CHG_USB) 369 set_bit(FLAG_VBUS_CHANGED, &tps->flags); 370 charging = 1; 371 } else if (tps->chgstatus & TPS_CHG_AC) 372 charging = 1; 373 } 374 if (charging != tps->charging) { 375 tps->charging = charging; 376 pr_info("%s: battery %scharging\n", 377 DRIVER_NAME, charging ? "" : 378 ((tps->chgstatus & (TPS_CHG_USB|TPS_CHG_AC)) 379 ? "NOT " : "dis")); 380 } 381 } 382 383 /* always poll to detect (a) power removal, without tps65013 384 * NO_CHG IRQ; or (b) restart of charging after stop. 385 */ 386 if ((tps->model != TPS65013 || !tps->charging) 387 && (tps->chgstatus & (TPS_CHG_USB|TPS_CHG_AC))) 388 poll = 1; 389 if (poll) 390 queue_delayed_work(system_power_efficient_wq, &tps->work, 391 POWER_POLL_DELAY); 392 393 /* also potentially gpio-in rise or fall */ 394 } 395 396 /* handle IRQs and polling using keventd for now */ 397 static void tps65010_work(struct work_struct *work) 398 { 399 struct tps65010 *tps; 400 401 tps = container_of(to_delayed_work(work), struct tps65010, work); 402 mutex_lock(&tps->lock); 403 404 tps65010_interrupt(tps); 405 406 if (test_and_clear_bit(FLAG_VBUS_CHANGED, &tps->flags)) { 407 u8 chgconfig, tmp; 408 409 chgconfig = i2c_smbus_read_byte_data(tps->client, 410 TPS_CHGCONFIG); 411 chgconfig &= ~(TPS_VBUS_500MA | TPS_VBUS_CHARGING); 412 if (tps->vbus == 500) 413 chgconfig |= TPS_VBUS_500MA | TPS_VBUS_CHARGING; 414 else if (tps->vbus >= 100) 415 chgconfig |= TPS_VBUS_CHARGING; 416 417 i2c_smbus_write_byte_data(tps->client, 418 TPS_CHGCONFIG, chgconfig); 419 420 /* vbus update fails unless VBUS is connected! */ 421 tmp = i2c_smbus_read_byte_data(tps->client, TPS_CHGCONFIG); 422 tps->chgconf = tmp; 423 show_chgconfig(tps->por, "update vbus", tmp); 424 } 425 426 if (test_and_clear_bit(FLAG_IRQ_ENABLE, &tps->flags)) 427 enable_irq(tps->client->irq); 428 429 mutex_unlock(&tps->lock); 430 } 431 432 static irqreturn_t tps65010_irq(int irq, void *_tps) 433 { 434 struct tps65010 *tps = _tps; 435 436 disable_irq_nosync(irq); 437 set_bit(FLAG_IRQ_ENABLE, &tps->flags); 438 queue_delayed_work(system_power_efficient_wq, &tps->work, 0); 439 return IRQ_HANDLED; 440 } 441 442 /*-------------------------------------------------------------------------*/ 443 444 /* offsets 0..3 == GPIO1..GPIO4 445 * offsets 4..5 == LED1/nPG, LED2 (we set one of the non-BLINK modes) 446 * offset 6 == vibrator motor driver 447 */ 448 static void 449 tps65010_gpio_set(struct gpio_chip *chip, unsigned offset, int value) 450 { 451 if (offset < 4) 452 tps65010_set_gpio_out_value(offset + 1, value); 453 else if (offset < 6) 454 tps65010_set_led(offset - 3, value ? ON : OFF); 455 else 456 tps65010_set_vib(value); 457 } 458 459 static int 460 tps65010_output(struct gpio_chip *chip, unsigned offset, int value) 461 { 462 /* GPIOs may be input-only */ 463 if (offset < 4) { 464 struct tps65010 *tps; 465 466 tps = gpiochip_get_data(chip); 467 if (!(tps->outmask & (1 << offset))) 468 return -EINVAL; 469 tps65010_set_gpio_out_value(offset + 1, value); 470 } else if (offset < 6) 471 tps65010_set_led(offset - 3, value ? ON : OFF); 472 else 473 tps65010_set_vib(value); 474 475 return 0; 476 } 477 478 static int tps65010_gpio_get(struct gpio_chip *chip, unsigned offset) 479 { 480 int value; 481 struct tps65010 *tps; 482 483 tps = gpiochip_get_data(chip); 484 485 if (offset < 4) { 486 value = i2c_smbus_read_byte_data(tps->client, TPS_DEFGPIO); 487 if (value < 0) 488 return value; 489 if (value & (1 << (offset + 4))) /* output */ 490 return !(value & (1 << offset)); 491 else /* input */ 492 return !!(value & (1 << offset)); 493 } 494 495 /* REVISIT we *could* report LED1/nPG and LED2 state ... */ 496 return 0; 497 } 498 499 500 /*-------------------------------------------------------------------------*/ 501 502 static struct tps65010 *the_tps; 503 504 static void tps65010_remove(struct i2c_client *client) 505 { 506 struct tps65010 *tps = i2c_get_clientdata(client); 507 struct tps65010_board *board = dev_get_platdata(&client->dev); 508 509 if (board && board->teardown) 510 board->teardown(client, &tps->chip); 511 if (client->irq > 0) 512 free_irq(client->irq, tps); 513 cancel_delayed_work_sync(&tps->work); 514 debugfs_remove(tps->file); 515 the_tps = NULL; 516 } 517 518 static int tps65010_probe(struct i2c_client *client) 519 { 520 const struct i2c_device_id *id = i2c_client_get_device_id(client); 521 struct tps65010 *tps; 522 int status; 523 struct tps65010_board *board = dev_get_platdata(&client->dev); 524 525 if (the_tps) { 526 dev_dbg(&client->dev, "only one tps6501x chip allowed\n"); 527 return -ENODEV; 528 } 529 530 if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA)) 531 return -EINVAL; 532 533 tps = devm_kzalloc(&client->dev, sizeof(*tps), GFP_KERNEL); 534 if (!tps) 535 return -ENOMEM; 536 537 mutex_init(&tps->lock); 538 INIT_DELAYED_WORK(&tps->work, tps65010_work); 539 tps->client = client; 540 tps->model = id->driver_data; 541 542 /* the IRQ is active low, but many gpio lines can't support that 543 * so this driver uses falling-edge triggers instead. 544 */ 545 if (client->irq > 0) { 546 status = request_irq(client->irq, tps65010_irq, 547 IRQF_TRIGGER_FALLING, DRIVER_NAME, tps); 548 if (status < 0) { 549 dev_dbg(&client->dev, "can't get IRQ %d, err %d\n", 550 client->irq, status); 551 return status; 552 } 553 /* annoying race here, ideally we'd have an option 554 * to claim the irq now and enable it later. 555 * FIXME genirq IRQF_NOAUTOEN now solves that ... 556 */ 557 disable_irq(client->irq); 558 set_bit(FLAG_IRQ_ENABLE, &tps->flags); 559 } else 560 dev_warn(&client->dev, "IRQ not configured!\n"); 561 562 563 switch (tps->model) { 564 case TPS65010: 565 case TPS65012: 566 tps->por = 1; 567 break; 568 /* else CHGCONFIG.POR is replaced by AUA, enabling a WAIT mode */ 569 } 570 tps->chgconf = i2c_smbus_read_byte_data(client, TPS_CHGCONFIG); 571 show_chgconfig(tps->por, "conf/init", tps->chgconf); 572 573 show_chgstatus("chg/init", 574 i2c_smbus_read_byte_data(client, TPS_CHGSTATUS)); 575 show_regstatus("reg/init", 576 i2c_smbus_read_byte_data(client, TPS_REGSTATUS)); 577 578 pr_debug("%s: vdcdc1 0x%02x, vdcdc2 %02x, vregs1 %02x\n", DRIVER_NAME, 579 i2c_smbus_read_byte_data(client, TPS_VDCDC1), 580 i2c_smbus_read_byte_data(client, TPS_VDCDC2), 581 i2c_smbus_read_byte_data(client, TPS_VREGS1)); 582 pr_debug("%s: defgpio 0x%02x, mask3 0x%02x\n", DRIVER_NAME, 583 i2c_smbus_read_byte_data(client, TPS_DEFGPIO), 584 i2c_smbus_read_byte_data(client, TPS_MASK3)); 585 586 i2c_set_clientdata(client, tps); 587 the_tps = tps; 588 589 #if defined(CONFIG_USB_GADGET) && !defined(CONFIG_USB_OTG) 590 /* USB hosts can't draw VBUS. OTG devices could, later 591 * when OTG infrastructure enables it. USB peripherals 592 * could be relying on VBUS while booting, though. 593 */ 594 tps->vbus = 100; 595 #endif 596 597 /* unmask the "interesting" irqs, then poll once to 598 * kickstart monitoring, initialize shadowed status 599 * registers, and maybe disable VBUS draw. 600 */ 601 tps->nmask1 = ~0; 602 (void) i2c_smbus_write_byte_data(client, TPS_MASK1, ~tps->nmask1); 603 604 tps->nmask2 = TPS_REG_ONOFF; 605 if (tps->model == TPS65013) 606 tps->nmask2 |= TPS_REG_NO_CHG; 607 (void) i2c_smbus_write_byte_data(client, TPS_MASK2, ~tps->nmask2); 608 609 (void) i2c_smbus_write_byte_data(client, TPS_MASK3, 0x0f 610 | i2c_smbus_read_byte_data(client, TPS_MASK3)); 611 612 tps65010_work(&tps->work.work); 613 614 tps->file = debugfs_create_file(DRIVER_NAME, S_IRUGO, NULL, 615 tps, DEBUG_FOPS); 616 617 /* optionally register GPIOs */ 618 if (board) { 619 tps->outmask = board->outmask; 620 621 tps->chip.label = client->name; 622 tps->chip.parent = &client->dev; 623 tps->chip.owner = THIS_MODULE; 624 625 tps->chip.set = tps65010_gpio_set; 626 tps->chip.direction_output = tps65010_output; 627 628 /* NOTE: only partial support for inputs; nyet IRQs */ 629 tps->chip.get = tps65010_gpio_get; 630 631 tps->chip.base = -1; 632 tps->chip.ngpio = 7; 633 tps->chip.can_sleep = 1; 634 635 status = gpiochip_add_data(&tps->chip, tps); 636 if (status < 0) 637 dev_err(&client->dev, "can't add gpiochip, err %d\n", 638 status); 639 else if (board->setup) { 640 status = board->setup(client, &tps->chip); 641 if (status < 0) { 642 dev_dbg(&client->dev, 643 "board %s %s err %d\n", 644 "setup", client->name, status); 645 status = 0; 646 } 647 } 648 } 649 650 return 0; 651 } 652 653 static const struct i2c_device_id tps65010_id[] = { 654 { "tps65010", TPS65010 }, 655 { "tps65011", TPS65011 }, 656 { "tps65012", TPS65012 }, 657 { "tps65013", TPS65013 }, 658 { "tps65014", TPS65011 }, /* tps65011 charging at 6.5V max */ 659 { } 660 }; 661 MODULE_DEVICE_TABLE(i2c, tps65010_id); 662 663 static struct i2c_driver tps65010_driver = { 664 .driver = { 665 .name = "tps65010", 666 }, 667 .probe = tps65010_probe, 668 .remove = tps65010_remove, 669 .id_table = tps65010_id, 670 }; 671 672 /*-------------------------------------------------------------------------*/ 673 674 /* Draw from VBUS: 675 * 0 mA -- DON'T DRAW (might supply power instead) 676 * 100 mA -- usb unit load (slowest charge rate) 677 * 500 mA -- usb high power (fast battery charge) 678 */ 679 int tps65010_set_vbus_draw(unsigned mA) 680 { 681 unsigned long flags; 682 683 if (!the_tps) 684 return -ENODEV; 685 686 /* assumes non-SMP */ 687 local_irq_save(flags); 688 if (mA >= 500) 689 mA = 500; 690 else if (mA >= 100) 691 mA = 100; 692 else 693 mA = 0; 694 the_tps->vbus = mA; 695 if ((the_tps->chgstatus & TPS_CHG_USB) 696 && test_and_set_bit( 697 FLAG_VBUS_CHANGED, &the_tps->flags)) { 698 /* gadget drivers call this in_irq() */ 699 queue_delayed_work(system_power_efficient_wq, &the_tps->work, 700 0); 701 } 702 local_irq_restore(flags); 703 704 return 0; 705 } 706 EXPORT_SYMBOL(tps65010_set_vbus_draw); 707 708 /*-------------------------------------------------------------------------*/ 709 /* tps65010_set_gpio_out_value parameter: 710 * gpio: GPIO1, GPIO2, GPIO3 or GPIO4 711 * value: LOW or HIGH 712 */ 713 int tps65010_set_gpio_out_value(unsigned gpio, unsigned value) 714 { 715 int status; 716 unsigned defgpio; 717 718 if (!the_tps) 719 return -ENODEV; 720 if ((gpio < GPIO1) || (gpio > GPIO4)) 721 return -EINVAL; 722 723 mutex_lock(&the_tps->lock); 724 725 defgpio = i2c_smbus_read_byte_data(the_tps->client, TPS_DEFGPIO); 726 727 /* Configure GPIO for output */ 728 defgpio |= 1 << (gpio + 3); 729 730 /* Writing 1 forces a logic 0 on that GPIO and vice versa */ 731 switch (value) { 732 case LOW: 733 defgpio |= 1 << (gpio - 1); /* set GPIO low by writing 1 */ 734 break; 735 /* case HIGH: */ 736 default: 737 defgpio &= ~(1 << (gpio - 1)); /* set GPIO high by writing 0 */ 738 break; 739 } 740 741 status = i2c_smbus_write_byte_data(the_tps->client, 742 TPS_DEFGPIO, defgpio); 743 744 pr_debug("%s: gpio%dout = %s, defgpio 0x%02x\n", DRIVER_NAME, 745 gpio, value ? "high" : "low", 746 i2c_smbus_read_byte_data(the_tps->client, TPS_DEFGPIO)); 747 748 mutex_unlock(&the_tps->lock); 749 return status; 750 } 751 EXPORT_SYMBOL(tps65010_set_gpio_out_value); 752 753 /*-------------------------------------------------------------------------*/ 754 /* tps65010_set_led parameter: 755 * led: LED1 or LED2 756 * mode: ON, OFF or BLINK 757 */ 758 int tps65010_set_led(unsigned led, unsigned mode) 759 { 760 int status; 761 unsigned led_on, led_per, offs; 762 763 if (!the_tps) 764 return -ENODEV; 765 766 if (led == LED1) 767 offs = 0; 768 else { 769 offs = 2; 770 led = LED2; 771 } 772 773 mutex_lock(&the_tps->lock); 774 775 pr_debug("%s: led%i_on 0x%02x\n", DRIVER_NAME, led, 776 i2c_smbus_read_byte_data(the_tps->client, 777 TPS_LED1_ON + offs)); 778 779 pr_debug("%s: led%i_per 0x%02x\n", DRIVER_NAME, led, 780 i2c_smbus_read_byte_data(the_tps->client, 781 TPS_LED1_PER + offs)); 782 783 switch (mode) { 784 case OFF: 785 led_on = 1 << 7; 786 led_per = 0 << 7; 787 break; 788 case ON: 789 led_on = 1 << 7; 790 led_per = 1 << 7; 791 break; 792 case BLINK: 793 led_on = 0x30 | (0 << 7); 794 led_per = 0x08 | (1 << 7); 795 break; 796 default: 797 printk(KERN_ERR "%s: Wrong mode parameter for set_led()\n", 798 DRIVER_NAME); 799 mutex_unlock(&the_tps->lock); 800 return -EINVAL; 801 } 802 803 status = i2c_smbus_write_byte_data(the_tps->client, 804 TPS_LED1_ON + offs, led_on); 805 806 if (status != 0) { 807 printk(KERN_ERR "%s: Failed to write led%i_on register\n", 808 DRIVER_NAME, led); 809 mutex_unlock(&the_tps->lock); 810 return status; 811 } 812 813 pr_debug("%s: led%i_on 0x%02x\n", DRIVER_NAME, led, 814 i2c_smbus_read_byte_data(the_tps->client, TPS_LED1_ON + offs)); 815 816 status = i2c_smbus_write_byte_data(the_tps->client, 817 TPS_LED1_PER + offs, led_per); 818 819 if (status != 0) { 820 printk(KERN_ERR "%s: Failed to write led%i_per register\n", 821 DRIVER_NAME, led); 822 mutex_unlock(&the_tps->lock); 823 return status; 824 } 825 826 pr_debug("%s: led%i_per 0x%02x\n", DRIVER_NAME, led, 827 i2c_smbus_read_byte_data(the_tps->client, 828 TPS_LED1_PER + offs)); 829 830 mutex_unlock(&the_tps->lock); 831 832 return status; 833 } 834 EXPORT_SYMBOL(tps65010_set_led); 835 836 /*-------------------------------------------------------------------------*/ 837 /* tps65010_set_vib parameter: 838 * value: ON or OFF 839 */ 840 int tps65010_set_vib(unsigned value) 841 { 842 int status; 843 unsigned vdcdc2; 844 845 if (!the_tps) 846 return -ENODEV; 847 848 mutex_lock(&the_tps->lock); 849 850 vdcdc2 = i2c_smbus_read_byte_data(the_tps->client, TPS_VDCDC2); 851 vdcdc2 &= ~(1 << 1); 852 if (value) 853 vdcdc2 |= (1 << 1); 854 status = i2c_smbus_write_byte_data(the_tps->client, 855 TPS_VDCDC2, vdcdc2); 856 857 pr_debug("%s: vibrator %s\n", DRIVER_NAME, value ? "on" : "off"); 858 859 mutex_unlock(&the_tps->lock); 860 return status; 861 } 862 EXPORT_SYMBOL(tps65010_set_vib); 863 864 /*-------------------------------------------------------------------------*/ 865 /* tps65010_set_low_pwr parameter: 866 * mode: ON or OFF 867 */ 868 int tps65010_set_low_pwr(unsigned mode) 869 { 870 int status; 871 unsigned vdcdc1; 872 873 if (!the_tps) 874 return -ENODEV; 875 876 mutex_lock(&the_tps->lock); 877 878 pr_debug("%s: %s low_pwr, vdcdc1 0x%02x\n", DRIVER_NAME, 879 mode ? "enable" : "disable", 880 i2c_smbus_read_byte_data(the_tps->client, TPS_VDCDC1)); 881 882 vdcdc1 = i2c_smbus_read_byte_data(the_tps->client, TPS_VDCDC1); 883 884 switch (mode) { 885 case OFF: 886 vdcdc1 &= ~TPS_ENABLE_LP; /* disable ENABLE_LP bit */ 887 break; 888 /* case ON: */ 889 default: 890 vdcdc1 |= TPS_ENABLE_LP; /* enable ENABLE_LP bit */ 891 break; 892 } 893 894 status = i2c_smbus_write_byte_data(the_tps->client, 895 TPS_VDCDC1, vdcdc1); 896 897 if (status != 0) 898 printk(KERN_ERR "%s: Failed to write vdcdc1 register\n", 899 DRIVER_NAME); 900 else 901 pr_debug("%s: vdcdc1 0x%02x\n", DRIVER_NAME, 902 i2c_smbus_read_byte_data(the_tps->client, TPS_VDCDC1)); 903 904 mutex_unlock(&the_tps->lock); 905 906 return status; 907 } 908 EXPORT_SYMBOL(tps65010_set_low_pwr); 909 910 /*-------------------------------------------------------------------------*/ 911 /* tps65010_config_vregs1 parameter: 912 * value to be written to VREGS1 register 913 * Note: The complete register is written, set all bits you need 914 */ 915 int tps65010_config_vregs1(unsigned value) 916 { 917 int status; 918 919 if (!the_tps) 920 return -ENODEV; 921 922 mutex_lock(&the_tps->lock); 923 924 pr_debug("%s: vregs1 0x%02x\n", DRIVER_NAME, 925 i2c_smbus_read_byte_data(the_tps->client, TPS_VREGS1)); 926 927 status = i2c_smbus_write_byte_data(the_tps->client, 928 TPS_VREGS1, value); 929 930 if (status != 0) 931 printk(KERN_ERR "%s: Failed to write vregs1 register\n", 932 DRIVER_NAME); 933 else 934 pr_debug("%s: vregs1 0x%02x\n", DRIVER_NAME, 935 i2c_smbus_read_byte_data(the_tps->client, TPS_VREGS1)); 936 937 mutex_unlock(&the_tps->lock); 938 939 return status; 940 } 941 EXPORT_SYMBOL(tps65010_config_vregs1); 942 943 int tps65010_config_vdcdc2(unsigned value) 944 { 945 struct i2c_client *c; 946 int status; 947 948 if (!the_tps) 949 return -ENODEV; 950 951 c = the_tps->client; 952 mutex_lock(&the_tps->lock); 953 954 pr_debug("%s: vdcdc2 0x%02x\n", DRIVER_NAME, 955 i2c_smbus_read_byte_data(c, TPS_VDCDC2)); 956 957 status = i2c_smbus_write_byte_data(c, TPS_VDCDC2, value); 958 959 if (status != 0) 960 printk(KERN_ERR "%s: Failed to write vdcdc2 register\n", 961 DRIVER_NAME); 962 else 963 pr_debug("%s: vregs1 0x%02x\n", DRIVER_NAME, 964 i2c_smbus_read_byte_data(c, TPS_VDCDC2)); 965 966 mutex_unlock(&the_tps->lock); 967 return status; 968 } 969 EXPORT_SYMBOL(tps65010_config_vdcdc2); 970 971 /*-------------------------------------------------------------------------*/ 972 /* tps65013_set_low_pwr parameter: 973 * mode: ON or OFF 974 */ 975 976 /* FIXME: Assumes AC or USB power is present. Setting AUA bit is not 977 required if power supply is through a battery */ 978 979 int tps65013_set_low_pwr(unsigned mode) 980 { 981 int status; 982 unsigned vdcdc1, chgconfig; 983 984 if (!the_tps || the_tps->por) 985 return -ENODEV; 986 987 mutex_lock(&the_tps->lock); 988 989 pr_debug("%s: %s low_pwr, chgconfig 0x%02x vdcdc1 0x%02x\n", 990 DRIVER_NAME, 991 mode ? "enable" : "disable", 992 i2c_smbus_read_byte_data(the_tps->client, TPS_CHGCONFIG), 993 i2c_smbus_read_byte_data(the_tps->client, TPS_VDCDC1)); 994 995 chgconfig = i2c_smbus_read_byte_data(the_tps->client, TPS_CHGCONFIG); 996 vdcdc1 = i2c_smbus_read_byte_data(the_tps->client, TPS_VDCDC1); 997 998 switch (mode) { 999 case OFF: 1000 chgconfig &= ~TPS65013_AUA; /* disable AUA bit */ 1001 vdcdc1 &= ~TPS_ENABLE_LP; /* disable ENABLE_LP bit */ 1002 break; 1003 /* case ON: */ 1004 default: 1005 chgconfig |= TPS65013_AUA; /* enable AUA bit */ 1006 vdcdc1 |= TPS_ENABLE_LP; /* enable ENABLE_LP bit */ 1007 break; 1008 } 1009 1010 status = i2c_smbus_write_byte_data(the_tps->client, 1011 TPS_CHGCONFIG, chgconfig); 1012 if (status != 0) { 1013 printk(KERN_ERR "%s: Failed to write chconfig register\n", 1014 DRIVER_NAME); 1015 mutex_unlock(&the_tps->lock); 1016 return status; 1017 } 1018 1019 chgconfig = i2c_smbus_read_byte_data(the_tps->client, TPS_CHGCONFIG); 1020 the_tps->chgconf = chgconfig; 1021 show_chgconfig(0, "chgconf", chgconfig); 1022 1023 status = i2c_smbus_write_byte_data(the_tps->client, 1024 TPS_VDCDC1, vdcdc1); 1025 1026 if (status != 0) 1027 printk(KERN_ERR "%s: Failed to write vdcdc1 register\n", 1028 DRIVER_NAME); 1029 else 1030 pr_debug("%s: vdcdc1 0x%02x\n", DRIVER_NAME, 1031 i2c_smbus_read_byte_data(the_tps->client, TPS_VDCDC1)); 1032 1033 mutex_unlock(&the_tps->lock); 1034 1035 return status; 1036 } 1037 EXPORT_SYMBOL(tps65013_set_low_pwr); 1038 1039 /*-------------------------------------------------------------------------*/ 1040 1041 static int __init tps_init(void) 1042 { 1043 return i2c_add_driver(&tps65010_driver); 1044 } 1045 /* NOTE: this MUST be initialized before the other parts of the system 1046 * that rely on it ... but after the i2c bus on which this relies. 1047 * That is, much earlier than on PC-type systems, which don't often use 1048 * I2C as a core system bus. 1049 */ 1050 subsys_initcall(tps_init); 1051 1052 static void __exit tps_exit(void) 1053 { 1054 i2c_del_driver(&tps65010_driver); 1055 } 1056 module_exit(tps_exit); 1057 1058