1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * DDR PHY Front End (DPFE) driver for Broadcom set top box SoCs 4 * 5 * Copyright (c) 2017 Broadcom 6 */ 7 8 /* 9 * This driver provides access to the DPFE interface of Broadcom STB SoCs. 10 * The firmware running on the DCPU inside the DDR PHY can provide current 11 * information about the system's RAM, for instance the DRAM refresh rate. 12 * This can be used as an indirect indicator for the DRAM's temperature. 13 * Slower refresh rate means cooler RAM, higher refresh rate means hotter 14 * RAM. 15 * 16 * Throughout the driver, we use readl_relaxed() and writel_relaxed(), which 17 * already contain the appropriate le32_to_cpu()/cpu_to_le32() calls. 18 * 19 * Note regarding the loading of the firmware image: we use be32_to_cpu() 20 * and le_32_to_cpu(), so we can support the following four cases: 21 * - LE kernel + LE firmware image (the most common case) 22 * - LE kernel + BE firmware image 23 * - BE kernel + LE firmware image 24 * - BE kernel + BE firmware image 25 * 26 * The DPCU always runs in big endian mode. The firmware image, however, can 27 * be in either format. Also, communication between host CPU and DCPU is 28 * always in little endian. 29 */ 30 31 #include <linux/delay.h> 32 #include <linux/firmware.h> 33 #include <linux/io.h> 34 #include <linux/module.h> 35 #include <linux/of.h> 36 #include <linux/platform_device.h> 37 38 #define DRVNAME "brcmstb-dpfe" 39 40 /* DCPU register offsets */ 41 #define REG_DCPU_RESET 0x0 42 #define REG_TO_DCPU_MBOX 0x10 43 #define REG_TO_HOST_MBOX 0x14 44 45 /* Macros to process offsets returned by the DCPU */ 46 #define DRAM_MSG_ADDR_OFFSET 0x0 47 #define DRAM_MSG_TYPE_OFFSET 0x1c 48 #define DRAM_MSG_ADDR_MASK ((1UL << DRAM_MSG_TYPE_OFFSET) - 1) 49 #define DRAM_MSG_TYPE_MASK ((1UL << \ 50 (BITS_PER_LONG - DRAM_MSG_TYPE_OFFSET)) - 1) 51 52 /* Message RAM */ 53 #define DCPU_MSG_RAM_START 0x100 54 #define DCPU_MSG_RAM(x) (DCPU_MSG_RAM_START + (x) * sizeof(u32)) 55 56 /* DRAM Info Offsets & Masks */ 57 #define DRAM_INFO_INTERVAL 0x0 58 #define DRAM_INFO_MR4 0x4 59 #define DRAM_INFO_ERROR 0x8 60 #define DRAM_INFO_MR4_MASK 0xff 61 #define DRAM_INFO_MR4_SHIFT 24 /* We need to look at byte 3 */ 62 63 /* DRAM MR4 Offsets & Masks */ 64 #define DRAM_MR4_REFRESH 0x0 /* Refresh rate */ 65 #define DRAM_MR4_SR_ABORT 0x3 /* Self Refresh Abort */ 66 #define DRAM_MR4_PPRE 0x4 /* Post-package repair entry/exit */ 67 #define DRAM_MR4_TH_OFFS 0x5 /* Thermal Offset; vendor specific */ 68 #define DRAM_MR4_TUF 0x7 /* Temperature Update Flag */ 69 70 #define DRAM_MR4_REFRESH_MASK 0x7 71 #define DRAM_MR4_SR_ABORT_MASK 0x1 72 #define DRAM_MR4_PPRE_MASK 0x1 73 #define DRAM_MR4_TH_OFFS_MASK 0x3 74 #define DRAM_MR4_TUF_MASK 0x1 75 76 /* DRAM Vendor Offsets & Masks (API v2) */ 77 #define DRAM_VENDOR_MR5 0x0 78 #define DRAM_VENDOR_MR6 0x4 79 #define DRAM_VENDOR_MR7 0x8 80 #define DRAM_VENDOR_MR8 0xc 81 #define DRAM_VENDOR_ERROR 0x10 82 #define DRAM_VENDOR_MASK 0xff 83 #define DRAM_VENDOR_SHIFT 24 /* We need to look at byte 3 */ 84 85 /* DRAM Information Offsets & Masks (API v3) */ 86 #define DRAM_DDR_INFO_MR4 0x0 87 #define DRAM_DDR_INFO_MR5 0x4 88 #define DRAM_DDR_INFO_MR6 0x8 89 #define DRAM_DDR_INFO_MR7 0xc 90 #define DRAM_DDR_INFO_MR8 0x10 91 #define DRAM_DDR_INFO_ERROR 0x14 92 #define DRAM_DDR_INFO_MASK 0xff 93 94 /* Reset register bits & masks */ 95 #define DCPU_RESET_SHIFT 0x0 96 #define DCPU_RESET_MASK 0x1 97 #define DCPU_CLK_DISABLE_SHIFT 0x2 98 99 /* DCPU return codes */ 100 #define DCPU_RET_ERROR_BIT BIT(31) 101 #define DCPU_RET_SUCCESS 0x1 102 #define DCPU_RET_ERR_HEADER (DCPU_RET_ERROR_BIT | BIT(0)) 103 #define DCPU_RET_ERR_INVAL (DCPU_RET_ERROR_BIT | BIT(1)) 104 #define DCPU_RET_ERR_CHKSUM (DCPU_RET_ERROR_BIT | BIT(2)) 105 #define DCPU_RET_ERR_COMMAND (DCPU_RET_ERROR_BIT | BIT(3)) 106 /* This error code is not firmware defined and only used in the driver. */ 107 #define DCPU_RET_ERR_TIMEDOUT (DCPU_RET_ERROR_BIT | BIT(4)) 108 109 /* Firmware magic */ 110 #define DPFE_BE_MAGIC 0xfe1010fe 111 #define DPFE_LE_MAGIC 0xfe0101fe 112 113 /* Error codes */ 114 #define ERR_INVALID_MAGIC -1 115 #define ERR_INVALID_SIZE -2 116 #define ERR_INVALID_CHKSUM -3 117 118 /* Message types */ 119 #define DPFE_MSG_TYPE_COMMAND 1 120 #define DPFE_MSG_TYPE_RESPONSE 2 121 122 #define DELAY_LOOP_MAX 1000 123 124 enum dpfe_msg_fields { 125 MSG_HEADER, 126 MSG_COMMAND, 127 MSG_ARG_COUNT, 128 MSG_ARG0, 129 MSG_FIELD_MAX = 16 /* Max number of arguments */ 130 }; 131 132 enum dpfe_commands { 133 DPFE_CMD_GET_INFO, 134 DPFE_CMD_GET_REFRESH, 135 DPFE_CMD_GET_VENDOR, 136 DPFE_CMD_MAX /* Last entry */ 137 }; 138 139 /* 140 * Format of the binary firmware file: 141 * 142 * entry 143 * 0 header 144 * value: 0xfe0101fe <== little endian 145 * 0xfe1010fe <== big endian 146 * 1 sequence: 147 * [31:16] total segments on this build 148 * [15:0] this segment sequence. 149 * 2 FW version 150 * 3 IMEM byte size 151 * 4 DMEM byte size 152 * IMEM 153 * DMEM 154 * last checksum ==> sum of everything 155 */ 156 struct dpfe_firmware_header { 157 u32 magic; 158 u32 sequence; 159 u32 version; 160 u32 imem_size; 161 u32 dmem_size; 162 }; 163 164 /* Things we only need during initialization. */ 165 struct init_data { 166 unsigned int dmem_len; 167 unsigned int imem_len; 168 unsigned int chksum; 169 bool is_big_endian; 170 }; 171 172 /* API version and corresponding commands */ 173 struct dpfe_api { 174 int version; 175 const char *fw_name; 176 const struct attribute_group **sysfs_attrs; 177 u32 command[DPFE_CMD_MAX][MSG_FIELD_MAX]; 178 }; 179 180 /* Things we need for as long as we are active. */ 181 struct brcmstb_dpfe_priv { 182 void __iomem *regs; 183 void __iomem *dmem; 184 void __iomem *imem; 185 struct device *dev; 186 const struct dpfe_api *dpfe_api; 187 struct mutex lock; 188 }; 189 190 /* 191 * Forward declaration of our sysfs attribute functions, so we can declare the 192 * attribute data structures early. 193 */ 194 static ssize_t show_info(struct device *, struct device_attribute *, char *); 195 static ssize_t show_refresh(struct device *, struct device_attribute *, char *); 196 static ssize_t store_refresh(struct device *, struct device_attribute *, 197 const char *, size_t); 198 static ssize_t show_vendor(struct device *, struct device_attribute *, char *); 199 static ssize_t show_dram(struct device *, struct device_attribute *, char *); 200 201 /* 202 * Declare our attributes early, so they can be referenced in the API data 203 * structure. We need to do this, because the attributes depend on the API 204 * version. 205 */ 206 static DEVICE_ATTR(dpfe_info, 0444, show_info, NULL); 207 static DEVICE_ATTR(dpfe_refresh, 0644, show_refresh, store_refresh); 208 static DEVICE_ATTR(dpfe_vendor, 0444, show_vendor, NULL); 209 static DEVICE_ATTR(dpfe_dram, 0444, show_dram, NULL); 210 211 /* API v2 sysfs attributes */ 212 static struct attribute *dpfe_v2_attrs[] = { 213 &dev_attr_dpfe_info.attr, 214 &dev_attr_dpfe_refresh.attr, 215 &dev_attr_dpfe_vendor.attr, 216 NULL 217 }; 218 ATTRIBUTE_GROUPS(dpfe_v2); 219 220 /* API v3 sysfs attributes */ 221 static struct attribute *dpfe_v3_attrs[] = { 222 &dev_attr_dpfe_info.attr, 223 &dev_attr_dpfe_dram.attr, 224 NULL 225 }; 226 ATTRIBUTE_GROUPS(dpfe_v3); 227 228 /* 229 * Old API v2 firmware commands, as defined in the rev 0.61 specification, we 230 * use a version set to 1 to denote that it is not compatible with the new API 231 * v2 and onwards. 232 */ 233 static const struct dpfe_api dpfe_api_old_v2 = { 234 .version = 1, 235 .fw_name = "dpfe.bin", 236 .sysfs_attrs = dpfe_v2_groups, 237 .command = { 238 [DPFE_CMD_GET_INFO] = { 239 [MSG_HEADER] = DPFE_MSG_TYPE_COMMAND, 240 [MSG_COMMAND] = 1, 241 [MSG_ARG_COUNT] = 1, 242 [MSG_ARG0] = 1, 243 }, 244 [DPFE_CMD_GET_REFRESH] = { 245 [MSG_HEADER] = DPFE_MSG_TYPE_COMMAND, 246 [MSG_COMMAND] = 2, 247 [MSG_ARG_COUNT] = 1, 248 [MSG_ARG0] = 1, 249 }, 250 [DPFE_CMD_GET_VENDOR] = { 251 [MSG_HEADER] = DPFE_MSG_TYPE_COMMAND, 252 [MSG_COMMAND] = 2, 253 [MSG_ARG_COUNT] = 1, 254 [MSG_ARG0] = 2, 255 }, 256 } 257 }; 258 259 /* 260 * API v2 firmware commands, as defined in the rev 0.8 specification, named new 261 * v2 here 262 */ 263 static const struct dpfe_api dpfe_api_new_v2 = { 264 .version = 2, 265 .fw_name = NULL, /* We expect the firmware to have been downloaded! */ 266 .sysfs_attrs = dpfe_v2_groups, 267 .command = { 268 [DPFE_CMD_GET_INFO] = { 269 [MSG_HEADER] = DPFE_MSG_TYPE_COMMAND, 270 [MSG_COMMAND] = 0x101, 271 }, 272 [DPFE_CMD_GET_REFRESH] = { 273 [MSG_HEADER] = DPFE_MSG_TYPE_COMMAND, 274 [MSG_COMMAND] = 0x201, 275 }, 276 [DPFE_CMD_GET_VENDOR] = { 277 [MSG_HEADER] = DPFE_MSG_TYPE_COMMAND, 278 [MSG_COMMAND] = 0x202, 279 }, 280 } 281 }; 282 283 /* API v3 firmware commands */ 284 static const struct dpfe_api dpfe_api_v3 = { 285 .version = 3, 286 .fw_name = NULL, /* We expect the firmware to have been downloaded! */ 287 .sysfs_attrs = dpfe_v3_groups, 288 .command = { 289 [DPFE_CMD_GET_INFO] = { 290 [MSG_HEADER] = DPFE_MSG_TYPE_COMMAND, 291 [MSG_COMMAND] = 0x0101, 292 [MSG_ARG_COUNT] = 1, 293 [MSG_ARG0] = 1, 294 }, 295 [DPFE_CMD_GET_REFRESH] = { 296 [MSG_HEADER] = DPFE_MSG_TYPE_COMMAND, 297 [MSG_COMMAND] = 0x0202, 298 [MSG_ARG_COUNT] = 0, 299 }, 300 /* There's no GET_VENDOR command in API v3. */ 301 }, 302 }; 303 304 static const char *get_error_text(unsigned int i) 305 { 306 static const char * const error_text[] = { 307 "Success", "Header code incorrect", 308 "Unknown command or argument", "Incorrect checksum", 309 "Malformed command", "Timed out", "Unknown error", 310 }; 311 312 if (unlikely(i >= ARRAY_SIZE(error_text))) 313 i = ARRAY_SIZE(error_text) - 1; 314 315 return error_text[i]; 316 } 317 318 static bool is_dcpu_enabled(struct brcmstb_dpfe_priv *priv) 319 { 320 u32 val; 321 322 mutex_lock(&priv->lock); 323 val = readl_relaxed(priv->regs + REG_DCPU_RESET); 324 mutex_unlock(&priv->lock); 325 326 return !(val & DCPU_RESET_MASK); 327 } 328 329 static void __disable_dcpu(struct brcmstb_dpfe_priv *priv) 330 { 331 u32 val; 332 333 if (!is_dcpu_enabled(priv)) 334 return; 335 336 mutex_lock(&priv->lock); 337 338 /* Put DCPU in reset if it's running. */ 339 val = readl_relaxed(priv->regs + REG_DCPU_RESET); 340 val |= (1 << DCPU_RESET_SHIFT); 341 writel_relaxed(val, priv->regs + REG_DCPU_RESET); 342 343 mutex_unlock(&priv->lock); 344 } 345 346 static void __enable_dcpu(struct brcmstb_dpfe_priv *priv) 347 { 348 void __iomem *regs = priv->regs; 349 u32 val; 350 351 mutex_lock(&priv->lock); 352 353 /* Clear mailbox registers. */ 354 writel_relaxed(0, regs + REG_TO_DCPU_MBOX); 355 writel_relaxed(0, regs + REG_TO_HOST_MBOX); 356 357 /* Disable DCPU clock gating */ 358 val = readl_relaxed(regs + REG_DCPU_RESET); 359 val &= ~(1 << DCPU_CLK_DISABLE_SHIFT); 360 writel_relaxed(val, regs + REG_DCPU_RESET); 361 362 /* Take DCPU out of reset */ 363 val = readl_relaxed(regs + REG_DCPU_RESET); 364 val &= ~(1 << DCPU_RESET_SHIFT); 365 writel_relaxed(val, regs + REG_DCPU_RESET); 366 367 mutex_unlock(&priv->lock); 368 } 369 370 static unsigned int get_msg_chksum(const u32 msg[], unsigned int max) 371 { 372 unsigned int sum = 0; 373 unsigned int i; 374 375 /* Don't include the last field in the checksum. */ 376 for (i = 0; i < max; i++) 377 sum += msg[i]; 378 379 return sum; 380 } 381 382 static void __iomem *get_msg_ptr(struct brcmstb_dpfe_priv *priv, u32 response, 383 char *buf, ssize_t *size) 384 { 385 unsigned int msg_type; 386 unsigned int offset; 387 void __iomem *ptr = NULL; 388 389 /* There is no need to use this function for API v3 or later. */ 390 if (unlikely(priv->dpfe_api->version >= 3)) 391 return NULL; 392 393 msg_type = (response >> DRAM_MSG_TYPE_OFFSET) & DRAM_MSG_TYPE_MASK; 394 offset = (response >> DRAM_MSG_ADDR_OFFSET) & DRAM_MSG_ADDR_MASK; 395 396 /* 397 * msg_type == 1: the offset is relative to the message RAM 398 * msg_type == 0: the offset is relative to the data RAM (this is the 399 * previous way of passing data) 400 * msg_type is anything else: there's critical hardware problem 401 */ 402 switch (msg_type) { 403 case 1: 404 ptr = priv->regs + DCPU_MSG_RAM_START + offset; 405 break; 406 case 0: 407 ptr = priv->dmem + offset; 408 break; 409 default: 410 dev_emerg(priv->dev, "invalid message reply from DCPU: %#x\n", 411 response); 412 if (buf && size) 413 *size = sprintf(buf, 414 "FATAL: communication error with DCPU\n"); 415 } 416 417 return ptr; 418 } 419 420 static void __finalize_command(struct brcmstb_dpfe_priv *priv) 421 { 422 unsigned int release_mbox; 423 424 /* 425 * It depends on the API version which MBOX register we have to write to 426 * signal we are done. 427 */ 428 release_mbox = (priv->dpfe_api->version < 2) 429 ? REG_TO_HOST_MBOX : REG_TO_DCPU_MBOX; 430 writel_relaxed(0, priv->regs + release_mbox); 431 } 432 433 static int __send_command(struct brcmstb_dpfe_priv *priv, unsigned int cmd, 434 u32 result[]) 435 { 436 void __iomem *regs = priv->regs; 437 unsigned int i, chksum, chksum_idx; 438 const u32 *msg; 439 int ret = 0; 440 u32 resp; 441 442 if (cmd >= DPFE_CMD_MAX) 443 return -1; 444 445 msg = priv->dpfe_api->command[cmd]; 446 447 mutex_lock(&priv->lock); 448 449 /* Wait for DCPU to become ready */ 450 for (i = 0; i < DELAY_LOOP_MAX; i++) { 451 resp = readl_relaxed(regs + REG_TO_HOST_MBOX); 452 if (resp == 0) 453 break; 454 msleep(1); 455 } 456 if (resp != 0) { 457 mutex_unlock(&priv->lock); 458 return -ffs(DCPU_RET_ERR_TIMEDOUT); 459 } 460 461 /* Compute checksum over the message */ 462 chksum_idx = msg[MSG_ARG_COUNT] + MSG_ARG_COUNT + 1; 463 chksum = get_msg_chksum(msg, chksum_idx); 464 465 /* Write command and arguments to message area */ 466 for (i = 0; i < MSG_FIELD_MAX; i++) { 467 if (i == chksum_idx) 468 writel_relaxed(chksum, regs + DCPU_MSG_RAM(i)); 469 else 470 writel_relaxed(msg[i], regs + DCPU_MSG_RAM(i)); 471 } 472 473 /* Tell DCPU there is a command waiting */ 474 writel_relaxed(1, regs + REG_TO_DCPU_MBOX); 475 476 /* Wait for DCPU to process the command */ 477 for (i = 0; i < DELAY_LOOP_MAX; i++) { 478 /* Read response code */ 479 resp = readl_relaxed(regs + REG_TO_HOST_MBOX); 480 if (resp > 0) 481 break; 482 msleep(1); 483 } 484 485 if (i == DELAY_LOOP_MAX) { 486 resp = (DCPU_RET_ERR_TIMEDOUT & ~DCPU_RET_ERROR_BIT); 487 ret = -ffs(resp); 488 } else { 489 /* Read response data */ 490 for (i = 0; i < MSG_FIELD_MAX; i++) 491 result[i] = readl_relaxed(regs + DCPU_MSG_RAM(i)); 492 chksum_idx = result[MSG_ARG_COUNT] + MSG_ARG_COUNT + 1; 493 } 494 495 /* Tell DCPU we are done */ 496 __finalize_command(priv); 497 498 mutex_unlock(&priv->lock); 499 500 if (ret) 501 return ret; 502 503 /* Verify response */ 504 chksum = get_msg_chksum(result, chksum_idx); 505 if (chksum != result[chksum_idx]) 506 resp = DCPU_RET_ERR_CHKSUM; 507 508 if (resp != DCPU_RET_SUCCESS) { 509 resp &= ~DCPU_RET_ERROR_BIT; 510 ret = -ffs(resp); 511 } 512 513 return ret; 514 } 515 516 /* Ensure that the firmware file loaded meets all the requirements. */ 517 static int __verify_firmware(struct init_data *init, 518 const struct firmware *fw) 519 { 520 const struct dpfe_firmware_header *header = (void *)fw->data; 521 unsigned int dmem_size, imem_size, total_size; 522 bool is_big_endian = false; 523 const u32 *chksum_ptr; 524 525 if (header->magic == DPFE_BE_MAGIC) 526 is_big_endian = true; 527 else if (header->magic != DPFE_LE_MAGIC) 528 return ERR_INVALID_MAGIC; 529 530 if (is_big_endian) { 531 dmem_size = be32_to_cpu(header->dmem_size); 532 imem_size = be32_to_cpu(header->imem_size); 533 } else { 534 dmem_size = le32_to_cpu(header->dmem_size); 535 imem_size = le32_to_cpu(header->imem_size); 536 } 537 538 /* Data and instruction sections are 32 bit words. */ 539 if ((dmem_size % sizeof(u32)) != 0 || (imem_size % sizeof(u32)) != 0) 540 return ERR_INVALID_SIZE; 541 542 /* 543 * The header + the data section + the instruction section + the 544 * checksum must be equal to the total firmware size. 545 */ 546 total_size = dmem_size + imem_size + sizeof(*header) + 547 sizeof(*chksum_ptr); 548 if (total_size != fw->size) 549 return ERR_INVALID_SIZE; 550 551 /* The checksum comes at the very end. */ 552 chksum_ptr = (void *)fw->data + sizeof(*header) + dmem_size + imem_size; 553 554 init->is_big_endian = is_big_endian; 555 init->dmem_len = dmem_size; 556 init->imem_len = imem_size; 557 init->chksum = (is_big_endian) 558 ? be32_to_cpu(*chksum_ptr) : le32_to_cpu(*chksum_ptr); 559 560 return 0; 561 } 562 563 /* Verify checksum by reading back the firmware from co-processor RAM. */ 564 static int __verify_fw_checksum(struct init_data *init, 565 struct brcmstb_dpfe_priv *priv, 566 const struct dpfe_firmware_header *header, 567 u32 checksum) 568 { 569 u32 magic, sequence, version, sum; 570 u32 __iomem *dmem = priv->dmem; 571 u32 __iomem *imem = priv->imem; 572 unsigned int i; 573 574 if (init->is_big_endian) { 575 magic = be32_to_cpu(header->magic); 576 sequence = be32_to_cpu(header->sequence); 577 version = be32_to_cpu(header->version); 578 } else { 579 magic = le32_to_cpu(header->magic); 580 sequence = le32_to_cpu(header->sequence); 581 version = le32_to_cpu(header->version); 582 } 583 584 sum = magic + sequence + version + init->dmem_len + init->imem_len; 585 586 for (i = 0; i < init->dmem_len / sizeof(u32); i++) 587 sum += readl_relaxed(dmem + i); 588 589 for (i = 0; i < init->imem_len / sizeof(u32); i++) 590 sum += readl_relaxed(imem + i); 591 592 return (sum == checksum) ? 0 : -1; 593 } 594 595 static int __write_firmware(u32 __iomem *mem, const u32 *fw, 596 unsigned int size, bool is_big_endian) 597 { 598 unsigned int i; 599 600 /* Convert size to 32-bit words. */ 601 size /= sizeof(u32); 602 603 /* It is recommended to clear the firmware area first. */ 604 for (i = 0; i < size; i++) 605 writel_relaxed(0, mem + i); 606 607 /* Now copy it. */ 608 if (is_big_endian) { 609 for (i = 0; i < size; i++) 610 writel_relaxed(be32_to_cpu(fw[i]), mem + i); 611 } else { 612 for (i = 0; i < size; i++) 613 writel_relaxed(le32_to_cpu(fw[i]), mem + i); 614 } 615 616 return 0; 617 } 618 619 static int brcmstb_dpfe_download_firmware(struct brcmstb_dpfe_priv *priv) 620 { 621 const struct dpfe_firmware_header *header; 622 unsigned int dmem_size, imem_size; 623 struct device *dev = priv->dev; 624 bool is_big_endian = false; 625 const struct firmware *fw; 626 const u32 *dmem, *imem; 627 struct init_data init; 628 const void *fw_blob; 629 int ret; 630 631 /* 632 * Skip downloading the firmware if the DCPU is already running and 633 * responding to commands. 634 */ 635 if (is_dcpu_enabled(priv)) { 636 u32 response[MSG_FIELD_MAX]; 637 638 ret = __send_command(priv, DPFE_CMD_GET_INFO, response); 639 if (!ret) 640 return 0; 641 } 642 643 /* 644 * If the firmware filename is NULL it means the boot firmware has to 645 * download the DCPU firmware for us. If that didn't work, we have to 646 * bail, since downloading it ourselves wouldn't work either. 647 */ 648 if (!priv->dpfe_api->fw_name) 649 return -ENODEV; 650 651 ret = firmware_request_nowarn(&fw, priv->dpfe_api->fw_name, dev); 652 /* 653 * Defer the firmware download if the firmware file couldn't be found. 654 * The root file system may not be available yet. 655 */ 656 if (ret) 657 return (ret == -ENOENT) ? -EPROBE_DEFER : ret; 658 659 ret = __verify_firmware(&init, fw); 660 if (ret) { 661 ret = -EFAULT; 662 goto release_fw; 663 } 664 665 __disable_dcpu(priv); 666 667 is_big_endian = init.is_big_endian; 668 dmem_size = init.dmem_len; 669 imem_size = init.imem_len; 670 671 /* At the beginning of the firmware blob is a header. */ 672 header = (struct dpfe_firmware_header *)fw->data; 673 /* Void pointer to the beginning of the actual firmware. */ 674 fw_blob = fw->data + sizeof(*header); 675 /* IMEM comes right after the header. */ 676 imem = fw_blob; 677 /* DMEM follows after IMEM. */ 678 dmem = fw_blob + imem_size; 679 680 ret = __write_firmware(priv->dmem, dmem, dmem_size, is_big_endian); 681 if (ret) 682 goto release_fw; 683 ret = __write_firmware(priv->imem, imem, imem_size, is_big_endian); 684 if (ret) 685 goto release_fw; 686 687 ret = __verify_fw_checksum(&init, priv, header, init.chksum); 688 if (ret) 689 goto release_fw; 690 691 __enable_dcpu(priv); 692 693 release_fw: 694 release_firmware(fw); 695 return ret; 696 } 697 698 static ssize_t generic_show(unsigned int command, u32 response[], 699 struct brcmstb_dpfe_priv *priv, char *buf) 700 { 701 int ret; 702 703 if (!priv) 704 return sprintf(buf, "ERROR: driver private data not set\n"); 705 706 ret = __send_command(priv, command, response); 707 if (ret < 0) 708 return sprintf(buf, "ERROR: %s\n", get_error_text(-ret)); 709 710 return 0; 711 } 712 713 static ssize_t show_info(struct device *dev, struct device_attribute *devattr, 714 char *buf) 715 { 716 u32 response[MSG_FIELD_MAX]; 717 struct brcmstb_dpfe_priv *priv; 718 unsigned int info; 719 ssize_t ret; 720 721 priv = dev_get_drvdata(dev); 722 ret = generic_show(DPFE_CMD_GET_INFO, response, priv, buf); 723 if (ret) 724 return ret; 725 726 info = response[MSG_ARG0]; 727 728 return sprintf(buf, "%u.%u.%u.%u\n", 729 (info >> 24) & 0xff, 730 (info >> 16) & 0xff, 731 (info >> 8) & 0xff, 732 info & 0xff); 733 } 734 735 static ssize_t show_refresh(struct device *dev, 736 struct device_attribute *devattr, char *buf) 737 { 738 u32 response[MSG_FIELD_MAX]; 739 void __iomem *info; 740 struct brcmstb_dpfe_priv *priv; 741 u8 refresh, sr_abort, ppre, thermal_offs, tuf; 742 u32 mr4; 743 ssize_t ret; 744 745 priv = dev_get_drvdata(dev); 746 ret = generic_show(DPFE_CMD_GET_REFRESH, response, priv, buf); 747 if (ret) 748 return ret; 749 750 info = get_msg_ptr(priv, response[MSG_ARG0], buf, &ret); 751 if (!info) 752 return ret; 753 754 mr4 = (readl_relaxed(info + DRAM_INFO_MR4) >> DRAM_INFO_MR4_SHIFT) & 755 DRAM_INFO_MR4_MASK; 756 757 refresh = (mr4 >> DRAM_MR4_REFRESH) & DRAM_MR4_REFRESH_MASK; 758 sr_abort = (mr4 >> DRAM_MR4_SR_ABORT) & DRAM_MR4_SR_ABORT_MASK; 759 ppre = (mr4 >> DRAM_MR4_PPRE) & DRAM_MR4_PPRE_MASK; 760 thermal_offs = (mr4 >> DRAM_MR4_TH_OFFS) & DRAM_MR4_TH_OFFS_MASK; 761 tuf = (mr4 >> DRAM_MR4_TUF) & DRAM_MR4_TUF_MASK; 762 763 return sprintf(buf, "%#x %#x %#x %#x %#x %#x %#x\n", 764 readl_relaxed(info + DRAM_INFO_INTERVAL), 765 refresh, sr_abort, ppre, thermal_offs, tuf, 766 readl_relaxed(info + DRAM_INFO_ERROR)); 767 } 768 769 static ssize_t store_refresh(struct device *dev, struct device_attribute *attr, 770 const char *buf, size_t count) 771 { 772 u32 response[MSG_FIELD_MAX]; 773 struct brcmstb_dpfe_priv *priv; 774 void __iomem *info; 775 unsigned long val; 776 int ret; 777 778 if (kstrtoul(buf, 0, &val) < 0) 779 return -EINVAL; 780 781 priv = dev_get_drvdata(dev); 782 ret = __send_command(priv, DPFE_CMD_GET_REFRESH, response); 783 if (ret) 784 return ret; 785 786 info = get_msg_ptr(priv, response[MSG_ARG0], NULL, NULL); 787 if (!info) 788 return -EIO; 789 790 writel_relaxed(val, info + DRAM_INFO_INTERVAL); 791 792 return count; 793 } 794 795 static ssize_t show_vendor(struct device *dev, struct device_attribute *devattr, 796 char *buf) 797 { 798 u32 response[MSG_FIELD_MAX]; 799 struct brcmstb_dpfe_priv *priv; 800 void __iomem *info; 801 ssize_t ret; 802 u32 mr5, mr6, mr7, mr8, err; 803 804 priv = dev_get_drvdata(dev); 805 ret = generic_show(DPFE_CMD_GET_VENDOR, response, priv, buf); 806 if (ret) 807 return ret; 808 809 info = get_msg_ptr(priv, response[MSG_ARG0], buf, &ret); 810 if (!info) 811 return ret; 812 813 mr5 = (readl_relaxed(info + DRAM_VENDOR_MR5) >> DRAM_VENDOR_SHIFT) & 814 DRAM_VENDOR_MASK; 815 mr6 = (readl_relaxed(info + DRAM_VENDOR_MR6) >> DRAM_VENDOR_SHIFT) & 816 DRAM_VENDOR_MASK; 817 mr7 = (readl_relaxed(info + DRAM_VENDOR_MR7) >> DRAM_VENDOR_SHIFT) & 818 DRAM_VENDOR_MASK; 819 mr8 = (readl_relaxed(info + DRAM_VENDOR_MR8) >> DRAM_VENDOR_SHIFT) & 820 DRAM_VENDOR_MASK; 821 err = readl_relaxed(info + DRAM_VENDOR_ERROR) & DRAM_VENDOR_MASK; 822 823 return sprintf(buf, "%#x %#x %#x %#x %#x\n", mr5, mr6, mr7, mr8, err); 824 } 825 826 static ssize_t show_dram(struct device *dev, struct device_attribute *devattr, 827 char *buf) 828 { 829 u32 response[MSG_FIELD_MAX]; 830 struct brcmstb_dpfe_priv *priv; 831 ssize_t ret; 832 u32 mr4, mr5, mr6, mr7, mr8, err; 833 834 priv = dev_get_drvdata(dev); 835 ret = generic_show(DPFE_CMD_GET_REFRESH, response, priv, buf); 836 if (ret) 837 return ret; 838 839 mr4 = response[MSG_ARG0 + 0] & DRAM_INFO_MR4_MASK; 840 mr5 = response[MSG_ARG0 + 1] & DRAM_DDR_INFO_MASK; 841 mr6 = response[MSG_ARG0 + 2] & DRAM_DDR_INFO_MASK; 842 mr7 = response[MSG_ARG0 + 3] & DRAM_DDR_INFO_MASK; 843 mr8 = response[MSG_ARG0 + 4] & DRAM_DDR_INFO_MASK; 844 err = response[MSG_ARG0 + 5] & DRAM_DDR_INFO_MASK; 845 846 return sprintf(buf, "%#x %#x %#x %#x %#x %#x\n", mr4, mr5, mr6, mr7, 847 mr8, err); 848 } 849 850 static int brcmstb_dpfe_resume(struct platform_device *pdev) 851 { 852 struct brcmstb_dpfe_priv *priv = platform_get_drvdata(pdev); 853 854 return brcmstb_dpfe_download_firmware(priv); 855 } 856 857 static int brcmstb_dpfe_probe(struct platform_device *pdev) 858 { 859 struct device *dev = &pdev->dev; 860 struct brcmstb_dpfe_priv *priv; 861 int ret; 862 863 priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); 864 if (!priv) 865 return -ENOMEM; 866 867 priv->dev = dev; 868 869 mutex_init(&priv->lock); 870 platform_set_drvdata(pdev, priv); 871 872 priv->regs = devm_platform_ioremap_resource_byname(pdev, "dpfe-cpu"); 873 if (IS_ERR(priv->regs)) { 874 dev_err(dev, "couldn't map DCPU registers\n"); 875 return -ENODEV; 876 } 877 878 priv->dmem = devm_platform_ioremap_resource_byname(pdev, "dpfe-dmem"); 879 if (IS_ERR(priv->dmem)) { 880 dev_err(dev, "Couldn't map DCPU data memory\n"); 881 return -ENOENT; 882 } 883 884 priv->imem = devm_platform_ioremap_resource_byname(pdev, "dpfe-imem"); 885 if (IS_ERR(priv->imem)) { 886 dev_err(dev, "Couldn't map DCPU instruction memory\n"); 887 return -ENOENT; 888 } 889 890 priv->dpfe_api = of_device_get_match_data(dev); 891 if (unlikely(!priv->dpfe_api)) { 892 /* 893 * It should be impossible to end up here, but to be safe we 894 * check anyway. 895 */ 896 dev_err(dev, "Couldn't determine API\n"); 897 return -ENOENT; 898 } 899 900 ret = brcmstb_dpfe_download_firmware(priv); 901 if (ret) 902 return dev_err_probe(dev, ret, "Couldn't download firmware\n"); 903 904 ret = sysfs_create_groups(&pdev->dev.kobj, priv->dpfe_api->sysfs_attrs); 905 if (!ret) 906 dev_info(dev, "registered with API v%d.\n", 907 priv->dpfe_api->version); 908 909 return ret; 910 } 911 912 static void brcmstb_dpfe_remove(struct platform_device *pdev) 913 { 914 struct brcmstb_dpfe_priv *priv = dev_get_drvdata(&pdev->dev); 915 916 sysfs_remove_groups(&pdev->dev.kobj, priv->dpfe_api->sysfs_attrs); 917 } 918 919 static const struct of_device_id brcmstb_dpfe_of_match[] = { 920 /* Use legacy API v2 for a select number of chips */ 921 { .compatible = "brcm,bcm7268-dpfe-cpu", .data = &dpfe_api_old_v2 }, 922 { .compatible = "brcm,bcm7271-dpfe-cpu", .data = &dpfe_api_old_v2 }, 923 { .compatible = "brcm,bcm7278-dpfe-cpu", .data = &dpfe_api_old_v2 }, 924 { .compatible = "brcm,bcm7211-dpfe-cpu", .data = &dpfe_api_new_v2 }, 925 /* API v3 is the default going forward */ 926 { .compatible = "brcm,dpfe-cpu", .data = &dpfe_api_v3 }, 927 {} 928 }; 929 MODULE_DEVICE_TABLE(of, brcmstb_dpfe_of_match); 930 931 static struct platform_driver brcmstb_dpfe_driver = { 932 .driver = { 933 .name = DRVNAME, 934 .of_match_table = brcmstb_dpfe_of_match, 935 }, 936 .probe = brcmstb_dpfe_probe, 937 .remove_new = brcmstb_dpfe_remove, 938 .resume = brcmstb_dpfe_resume, 939 }; 940 941 module_platform_driver(brcmstb_dpfe_driver); 942 943 MODULE_AUTHOR("Markus Mayer <mmayer@broadcom.com>"); 944 MODULE_DESCRIPTION("BRCMSTB DDR PHY Front End Driver"); 945 MODULE_LICENSE("GPL"); 946