1 /* SPDX-License-Identifier: GPL-2.0 */ 2 3 /* 4 * em28xx-reg.h - Register definitions for em28xx driver 5 */ 6 7 #define EM_GPIO_0 ((unsigned char)BIT(0)) 8 #define EM_GPIO_1 ((unsigned char)BIT(1)) 9 #define EM_GPIO_2 ((unsigned char)BIT(2)) 10 #define EM_GPIO_3 ((unsigned char)BIT(3)) 11 #define EM_GPIO_4 ((unsigned char)BIT(4)) 12 #define EM_GPIO_5 ((unsigned char)BIT(5)) 13 #define EM_GPIO_6 ((unsigned char)BIT(6)) 14 #define EM_GPIO_7 ((unsigned char)BIT(7)) 15 16 #define EM_GPO_0 ((unsigned char)BIT(0)) 17 #define EM_GPO_1 ((unsigned char)BIT(1)) 18 #define EM_GPO_2 ((unsigned char)BIT(2)) 19 #define EM_GPO_3 ((unsigned char)BIT(3)) 20 21 /* em28xx endpoints */ 22 /* 0x82: (always ?) analog */ 23 #define EM28XX_EP_AUDIO 0x83 24 /* 0x84: digital or analog */ 25 26 /* em2800 registers */ 27 #define EM2800_R08_AUDIOSRC 0x08 28 29 /* em28xx registers */ 30 31 #define EM28XX_R00_CHIPCFG 0x00 32 33 /* em28xx Chip Configuration 0x00 */ 34 #define EM2860_CHIPCFG_VENDOR_AUDIO 0x80 35 #define EM2860_CHIPCFG_I2S_VOLUME_CAPABLE 0x40 36 #define EM2820_CHIPCFG_I2S_3_SAMPRATES 0x30 37 #define EM2860_CHIPCFG_I2S_5_SAMPRATES 0x30 38 #define EM2820_CHIPCFG_I2S_1_SAMPRATE 0x20 39 #define EM2860_CHIPCFG_I2S_3_SAMPRATES 0x20 40 #define EM28XX_CHIPCFG_AC97 0x10 41 #define EM28XX_CHIPCFG_AUDIOMASK 0x30 42 43 #define EM28XX_R01_CHIPCFG2 0x01 44 45 /* em28xx Chip Configuration 2 0x01 */ 46 #define EM28XX_CHIPCFG2_TS_PRESENT 0x10 47 #define EM28XX_CHIPCFG2_TS_REQ_INTERVAL_MASK 0x0c /* bits 3-2 */ 48 #define EM28XX_CHIPCFG2_TS_REQ_INTERVAL_1MF 0x00 49 #define EM28XX_CHIPCFG2_TS_REQ_INTERVAL_2MF 0x04 50 #define EM28XX_CHIPCFG2_TS_REQ_INTERVAL_4MF 0x08 51 #define EM28XX_CHIPCFG2_TS_REQ_INTERVAL_8MF 0x0c 52 #define EM28XX_CHIPCFG2_TS_PACKETSIZE_MASK 0x03 /* bits 0-1 */ 53 #define EM28XX_CHIPCFG2_TS_PACKETSIZE_188 0x00 54 #define EM28XX_CHIPCFG2_TS_PACKETSIZE_376 0x01 55 #define EM28XX_CHIPCFG2_TS_PACKETSIZE_564 0x02 56 #define EM28XX_CHIPCFG2_TS_PACKETSIZE_752 0x03 57 58 /* GPIO/GPO registers */ 59 #define EM2880_R04_GPO 0x04 /* em2880-em2883 only */ 60 #define EM2820_R08_GPIO_CTRL 0x08 /* em2820-em2873/83 only */ 61 #define EM2820_R09_GPIO_STATE 0x09 /* em2820-em2873/83 only */ 62 63 #define EM28XX_R06_I2C_CLK 0x06 64 65 /* em28xx I2C Clock Register (0x06) */ 66 #define EM28XX_I2C_CLK_ACK_LAST_READ 0x80 67 #define EM28XX_I2C_CLK_WAIT_ENABLE 0x40 68 #define EM28XX_I2C_EEPROM_ON_BOARD 0x08 69 #define EM28XX_I2C_EEPROM_KEY_VALID 0x04 70 #define EM2874_I2C_SECONDARY_BUS_SELECT 0x04 /* em2874 has two i2c busses */ 71 #define EM28XX_I2C_FREQ_1_5_MHZ 0x03 /* bus frequency (bits [1-0]) */ 72 #define EM28XX_I2C_FREQ_25_KHZ 0x02 73 #define EM28XX_I2C_FREQ_400_KHZ 0x01 74 #define EM28XX_I2C_FREQ_100_KHZ 0x00 75 76 #define EM28XX_R0A_CHIPID 0x0a 77 #define EM28XX_R0C_USBSUSP 0x0c 78 #define EM28XX_R0C_USBSUSP_SNAPSHOT 0x20 /* 1=button pressed, needs reset */ 79 80 #define EM28XX_R0E_AUDIOSRC 0x0e 81 #define EM28XX_R0F_XCLK 0x0f 82 83 /* em28xx XCLK Register (0x0f) */ 84 #define EM28XX_XCLK_AUDIO_UNMUTE 0x80 /* otherwise audio muted */ 85 #define EM28XX_XCLK_I2S_MSB_TIMING 0x40 /* otherwise standard timing */ 86 #define EM28XX_XCLK_IR_RC5_MODE 0x20 /* otherwise NEC mode */ 87 #define EM28XX_XCLK_IR_NEC_CHK_PARITY 0x10 88 #define EM28XX_XCLK_FREQUENCY_30MHZ 0x00 /* Freq. select (bits [3-0]) */ 89 #define EM28XX_XCLK_FREQUENCY_15MHZ 0x01 90 #define EM28XX_XCLK_FREQUENCY_10MHZ 0x02 91 #define EM28XX_XCLK_FREQUENCY_7_5MHZ 0x03 92 #define EM28XX_XCLK_FREQUENCY_6MHZ 0x04 93 #define EM28XX_XCLK_FREQUENCY_5MHZ 0x05 94 #define EM28XX_XCLK_FREQUENCY_4_3MHZ 0x06 95 #define EM28XX_XCLK_FREQUENCY_12MHZ 0x07 96 #define EM28XX_XCLK_FREQUENCY_20MHZ 0x08 97 #define EM28XX_XCLK_FREQUENCY_20MHZ_2 0x09 98 #define EM28XX_XCLK_FREQUENCY_48MHZ 0x0a 99 #define EM28XX_XCLK_FREQUENCY_24MHZ 0x0b 100 101 #define EM28XX_R10_VINMODE 0x10 102 /* used by all non-camera devices: */ 103 #define EM28XX_VINMODE_YUV422_CbYCrY 0x10 104 /* used by camera devices: */ 105 #define EM28XX_VINMODE_YUV422_YUYV 0x08 106 #define EM28XX_VINMODE_YUV422_YVYU 0x09 107 #define EM28XX_VINMODE_YUV422_UYVY 0x0a 108 #define EM28XX_VINMODE_YUV422_VYUY 0x0b 109 #define EM28XX_VINMODE_RGB8_BGGR 0x0c 110 #define EM28XX_VINMODE_RGB8_GRBG 0x0d 111 #define EM28XX_VINMODE_RGB8_GBRG 0x0e 112 #define EM28XX_VINMODE_RGB8_RGGB 0x0f 113 /* 114 * apparently: 115 * bit 0: swap component 1+2 with 3+4 116 * => e.g.: YUYV => YVYU, BGGR => GRBG 117 * bit 1: swap component 1 with 2 and 3 with 4 118 * => e.g.: YUYV => UYVY, BGGR => GBRG 119 */ 120 121 #define EM28XX_R11_VINCTRL 0x11 122 123 /* em28xx Video Input Control Register 0x11 */ 124 #define EM28XX_VINCTRL_VBI_SLICED 0x80 125 #define EM28XX_VINCTRL_VBI_RAW 0x40 126 #define EM28XX_VINCTRL_VOUT_MODE_IN 0x20 /* HREF,VREF,VACT in output */ 127 #define EM28XX_VINCTRL_CCIR656_ENABLE 0x10 128 #define EM28XX_VINCTRL_VBI_16BIT_RAW 0x08 /* otherwise 8-bit raw */ 129 #define EM28XX_VINCTRL_FID_ON_HREF 0x04 130 #define EM28XX_VINCTRL_DUAL_EDGE_STROBE 0x02 131 #define EM28XX_VINCTRL_INTERLACED 0x01 132 133 #define EM28XX_R12_VINENABLE 0x12 /* */ 134 135 #define EM28XX_R14_GAMMA 0x14 136 #define EM28XX_R15_RGAIN 0x15 137 #define EM28XX_R16_GGAIN 0x16 138 #define EM28XX_R17_BGAIN 0x17 139 #define EM28XX_R18_ROFFSET 0x18 140 #define EM28XX_R19_GOFFSET 0x19 141 #define EM28XX_R1A_BOFFSET 0x1a 142 143 #define EM28XX_R1B_OFLOW 0x1b 144 #define EM28XX_R1C_HSTART 0x1c 145 #define EM28XX_R1D_VSTART 0x1d 146 #define EM28XX_R1E_CWIDTH 0x1e 147 #define EM28XX_R1F_CHEIGHT 0x1f 148 149 #define EM28XX_R20_YGAIN 0x20 /* contrast [0:4] */ 150 #define CONTRAST_DEFAULT 0x10 151 152 #define EM28XX_R21_YOFFSET 0x21 /* brightness */ /* signed */ 153 #define BRIGHTNESS_DEFAULT 0x00 154 155 #define EM28XX_R22_UVGAIN 0x22 /* saturation [0:4] */ 156 #define SATURATION_DEFAULT 0x10 157 158 #define EM28XX_R23_UOFFSET 0x23 /* blue balance */ /* signed */ 159 #define BLUE_BALANCE_DEFAULT 0x00 160 161 #define EM28XX_R24_VOFFSET 0x24 /* red balance */ /* signed */ 162 #define RED_BALANCE_DEFAULT 0x00 163 164 #define EM28XX_R25_SHARPNESS 0x25 /* sharpness [0:4] */ 165 #define SHARPNESS_DEFAULT 0x00 166 167 #define EM28XX_R26_COMPR 0x26 168 #define EM28XX_R27_OUTFMT 0x27 169 170 /* em28xx Output Format Register (0x27) */ 171 #define EM28XX_OUTFMT_RGB_8_RGRG 0x00 172 #define EM28XX_OUTFMT_RGB_8_GRGR 0x01 173 #define EM28XX_OUTFMT_RGB_8_GBGB 0x02 174 #define EM28XX_OUTFMT_RGB_8_BGBG 0x03 175 #define EM28XX_OUTFMT_RGB_16_656 0x04 176 #define EM28XX_OUTFMT_RGB_8_BAYER 0x08 /* Pattern in Reg 0x10[1-0] */ 177 #define EM28XX_OUTFMT_YUV211 0x10 178 #define EM28XX_OUTFMT_YUV422_Y0UY1V 0x14 179 #define EM28XX_OUTFMT_YUV422_Y1UY0V 0x15 180 #define EM28XX_OUTFMT_YUV411 0x18 181 182 #define EM28XX_R28_XMIN 0x28 183 #define EM28XX_R29_XMAX 0x29 184 #define EM28XX_R2A_YMIN 0x2a 185 #define EM28XX_R2B_YMAX 0x2b 186 187 #define EM28XX_R30_HSCALELOW 0x30 188 #define EM28XX_R31_HSCALEHIGH 0x31 189 #define EM28XX_R32_VSCALELOW 0x32 190 #define EM28XX_R33_VSCALEHIGH 0x33 191 #define EM28XX_HVSCALE_MAX 0x3fff /* => 20% */ 192 193 #define EM28XX_R34_VBI_START_H 0x34 194 #define EM28XX_R35_VBI_START_V 0x35 195 /* 196 * NOTE: the EM276x (and EM25xx, EM277x/8x ?) (camera bridges) use these 197 * registers for a different unknown purpose. 198 * => register 0x34 is set to capture width / 16 199 * => register 0x35 is set to capture height / 16 200 */ 201 202 #define EM28XX_R36_VBI_WIDTH 0x36 203 #define EM28XX_R37_VBI_HEIGHT 0x37 204 205 #define EM28XX_R40_AC97LSB 0x40 206 #define EM28XX_R41_AC97MSB 0x41 207 #define EM28XX_R42_AC97ADDR 0x42 208 #define EM28XX_R43_AC97BUSY 0x43 209 210 #define EM28XX_R45_IR 0x45 211 /* 212 * 0x45 bit 7 - parity bit 213 * bits 6-0 - count 214 * 0x46 IR brand 215 * 0x47 IR data 216 */ 217 218 /* em2874 registers */ 219 #define EM2874_R50_IR_CONFIG 0x50 220 #define EM2874_R51_IR 0x51 221 #define EM2874_R5D_TS1_PKT_SIZE 0x5d 222 #define EM2874_R5E_TS2_PKT_SIZE 0x5e 223 /* 224 * For both TS1 and TS2, In isochronous mode: 225 * 0x01 188 bytes 226 * 0x02 376 bytes 227 * 0x03 564 bytes 228 * 0x04 752 bytes 229 * 0x05 940 bytes 230 * In bulk mode: 231 * 0x01..0xff total packet count in 188-byte 232 */ 233 234 #define EM2874_R5F_TS_ENABLE 0x5f 235 236 /* em2874/174/84, em25xx, em276x/7x/8x GPIO registers */ 237 /* 238 * NOTE: not all ports are bonded out; 239 * Some ports are multiplexed with special function I/O 240 */ 241 #define EM2874_R80_GPIO_P0_CTRL 0x80 242 #define EM2874_R81_GPIO_P1_CTRL 0x81 243 #define EM2874_R82_GPIO_P2_CTRL 0x82 244 #define EM2874_R83_GPIO_P3_CTRL 0x83 245 #define EM2874_R84_GPIO_P0_STATE 0x84 246 #define EM2874_R85_GPIO_P1_STATE 0x85 247 #define EM2874_R86_GPIO_P2_STATE 0x86 248 #define EM2874_R87_GPIO_P3_STATE 0x87 249 250 /* em2874 IR config register (0x50) */ 251 #define EM2874_IR_NEC 0x00 252 #define EM2874_IR_NEC_NO_PARITY 0x01 253 #define EM2874_IR_RC5 0x04 254 #define EM2874_IR_RC6_MODE_0 0x08 255 #define EM2874_IR_RC6_MODE_6A 0x0b 256 257 /* em2874 Transport Stream Enable Register (0x5f) */ 258 #define EM2874_TS1_CAPTURE_ENABLE ((unsigned char)BIT(0)) 259 #define EM2874_TS1_FILTER_ENABLE ((unsigned char)BIT(1)) 260 #define EM2874_TS1_NULL_DISCARD ((unsigned char)BIT(2)) 261 #define EM2874_TS2_CAPTURE_ENABLE ((unsigned char)BIT(4)) 262 #define EM2874_TS2_FILTER_ENABLE ((unsigned char)BIT(5)) 263 #define EM2874_TS2_NULL_DISCARD ((unsigned char)BIT(6)) 264 265 /* register settings */ 266 #define EM2800_AUDIO_SRC_TUNER 0x0d 267 #define EM2800_AUDIO_SRC_LINE 0x0c 268 #define EM28XX_AUDIO_SRC_TUNER 0xc0 269 #define EM28XX_AUDIO_SRC_LINE 0x80 270 271 /* FIXME: Need to be populated with the other chip ID's */ 272 enum em28xx_chip_id { 273 CHIP_ID_EM2800 = 7, 274 CHIP_ID_EM2710 = 17, 275 CHIP_ID_EM2820 = 18, /* Also used by some em2710 */ 276 CHIP_ID_EM2840 = 20, 277 CHIP_ID_EM2750 = 33, 278 CHIP_ID_EM2860 = 34, 279 CHIP_ID_EM2870 = 35, 280 CHIP_ID_EM2883 = 36, 281 CHIP_ID_EM2765 = 54, 282 CHIP_ID_EM2874 = 65, 283 CHIP_ID_EM2884 = 68, 284 CHIP_ID_EM28174 = 113, 285 CHIP_ID_EM28178 = 114, 286 }; 287 288 /* 289 * Registers used by em202 290 */ 291 292 /* EMP202 vendor registers */ 293 #define EM202_EXT_MODEM_CTRL 0x3e 294 #define EM202_GPIO_CONF 0x4c 295 #define EM202_GPIO_POLARITY 0x4e 296 #define EM202_GPIO_STICKY 0x50 297 #define EM202_GPIO_MASK 0x52 298 #define EM202_GPIO_STATUS 0x54 299 #define EM202_SPDIF_OUT_SEL 0x6a 300 #define EM202_ANTIPOP 0x72 301 #define EM202_EAPD_GPIO_ACCESS 0x74 302