1# 2# Multimedia Video device configuration 3# 4 5menuconfig RADIO_ADAPTERS 6 bool "Radio Adapters" 7 depends on VIDEO_V4L2 8 default y 9 ---help--- 10 Say Y here to enable selecting AM/FM radio adapters. 11 12if RADIO_ADAPTERS && VIDEO_V4L2 13 14config RADIO_SI470X 15 bool "Silicon Labs Si470x FM Radio Receiver support" 16 depends on VIDEO_V4L2 17 18source "drivers/media/radio/si470x/Kconfig" 19 20config USB_MR800 21 tristate "AverMedia MR 800 USB FM radio support" 22 depends on USB && VIDEO_V4L2 23 ---help--- 24 Say Y here if you want to connect this type of radio to your 25 computer's USB port. Note that the audio is not digital, and 26 you must connect the line out connector to a sound card or a 27 set of speakers. 28 29 To compile this driver as a module, choose M here: the 30 module will be called radio-mr800. 31 32config USB_DSBR 33 tristate "D-Link/GemTek USB FM radio support" 34 depends on USB && VIDEO_V4L2 35 ---help--- 36 Say Y here if you want to connect this type of radio to your 37 computer's USB port. Note that the audio is not digital, and 38 you must connect the line out connector to a sound card or a 39 set of speakers. 40 41 To compile this driver as a module, choose M here: the 42 module will be called dsbr100. 43 44config RADIO_MAXIRADIO 45 tristate "Guillemot MAXI Radio FM 2000 radio" 46 depends on VIDEO_V4L2 && PCI 47 ---help--- 48 Choose Y here if you have this radio card. This card may also be 49 found as Gemtek PCI FM. 50 51 In order to control your radio card, you will need to use programs 52 that are compatible with the Video For Linux API. Information on 53 this API and pointers to "v4l" programs may be found at 54 <file:Documentation/video4linux/API.html>. 55 56 To compile this driver as a module, choose M here: the 57 module will be called radio-maxiradio. 58 59 60config I2C_SI4713 61 tristate "I2C driver for Silicon Labs Si4713 device" 62 depends on I2C && VIDEO_V4L2 63 ---help--- 64 Say Y here if you want support to Si4713 I2C device. 65 This device driver supports only i2c bus. 66 67 To compile this driver as a module, choose M here: the 68 module will be called si4713. 69 70config RADIO_SI4713 71 tristate "Silicon Labs Si4713 FM Radio Transmitter support" 72 depends on I2C && VIDEO_V4L2 73 select I2C_SI4713 74 ---help--- 75 Say Y here if you want support to Si4713 FM Radio Transmitter. 76 This device can transmit audio through FM. It can transmit 77 RDS and RBDS signals as well. This module is the v4l2 radio 78 interface for the i2c driver of this device. 79 80 To compile this driver as a module, choose M here: the 81 module will be called radio-si4713. 82 83config USB_KEENE 84 tristate "Keene FM Transmitter USB support" 85 depends on USB && VIDEO_V4L2 86 ---help--- 87 Say Y here if you want to connect this type of FM transmitter 88 to your computer's USB port. 89 90 To compile this driver as a module, choose M here: the 91 module will be called radio-keene. 92 93config RADIO_TEA5764 94 tristate "TEA5764 I2C FM radio support" 95 depends on I2C && VIDEO_V4L2 96 ---help--- 97 Say Y here if you want to use the TEA5764 FM chip found in 98 EZX phones. This FM chip is present in EZX phones from Motorola, 99 connected to internal pxa I2C bus. 100 101 To compile this driver as a module, choose M here: the 102 module will be called radio-tea5764. 103 104config RADIO_TEA5764_XTAL 105 bool "TEA5764 crystal reference" 106 depends on RADIO_TEA5764=y 107 default y 108 help 109 Say Y here if TEA5764 have a 32768 Hz crystal in circuit, say N 110 here if TEA5764 reference frequency is connected in FREQIN. 111 112config RADIO_SAA7706H 113 tristate "SAA7706H Car Radio DSP" 114 depends on I2C && VIDEO_V4L2 115 ---help--- 116 Say Y here if you want to use the SAA7706H Car radio Digital 117 Signal Processor, found for instance on the Russellville development 118 board. On the russellville the device is connected to internal 119 timberdale I2C bus. 120 121 To compile this driver as a module, choose M here: the 122 module will be called SAA7706H. 123 124config RADIO_TEF6862 125 tristate "TEF6862 Car Radio Enhanced Selectivity Tuner" 126 depends on I2C && VIDEO_V4L2 127 ---help--- 128 Say Y here if you want to use the TEF6862 Car Radio Enhanced 129 Selectivity Tuner, found for instance on the Russellville development 130 board. On the russellville the device is connected to internal 131 timberdale I2C bus. 132 133 To compile this driver as a module, choose M here: the 134 module will be called TEF6862. 135 136config RADIO_TIMBERDALE 137 tristate "Enable the Timberdale radio driver" 138 depends on MFD_TIMBERDALE && VIDEO_V4L2 139 depends on I2C # for RADIO_SAA7706H 140 select RADIO_TEF6862 141 select RADIO_SAA7706H 142 ---help--- 143 This is a kind of umbrella driver for the Radio Tuner and DSP 144 found behind the Timberdale FPGA on the Russellville board. 145 Enabling this driver will automatically select the DSP and tuner. 146 147config RADIO_WL1273 148 tristate "Texas Instruments WL1273 I2C FM Radio" 149 depends on I2C && VIDEO_V4L2 150 select MFD_CORE 151 select MFD_WL1273_CORE 152 select FW_LOADER 153 ---help--- 154 Choose Y here if you have this FM radio chip. 155 156 In order to control your radio card, you will need to use programs 157 that are compatible with the Video For Linux 2 API. Information on 158 this API and pointers to "v4l2" programs may be found at 159 <file:Documentation/video4linux/API.html>. 160 161 To compile this driver as a module, choose M here: the 162 module will be called radio-wl1273. 163 164# TI's ST based wl128x FM radio 165source "drivers/media/radio/wl128x/Kconfig" 166 167# 168# ISA drivers configuration 169# 170 171menuconfig V4L_RADIO_ISA_DRIVERS 172 bool "ISA radio devices" 173 depends on ISA 174 default n 175 ---help--- 176 Say Y here to enable support for these ISA drivers. 177 178if V4L_RADIO_ISA_DRIVERS 179 180config RADIO_ISA 181 depends on ISA 182 tristate 183 184config RADIO_CADET 185 tristate "ADS Cadet AM/FM Tuner" 186 depends on ISA && VIDEO_V4L2 187 ---help--- 188 Choose Y here if you have one of these AM/FM radio cards, and then 189 fill in the port address below. 190 191 In order to control your radio card, you will need to use programs 192 that are compatible with the Video For Linux API. Information on 193 this API and pointers to "v4l" programs may be found at 194 <file:Documentation/video4linux/API.html>. 195 196 Further documentation on this driver can be found on the WWW at 197 <http://linux.blackhawke.net/cadet/>. 198 199 To compile this driver as a module, choose M here: the 200 module will be called radio-cadet. 201 202config RADIO_RTRACK 203 tristate "AIMSlab RadioTrack (aka RadioReveal) support" 204 depends on ISA && VIDEO_V4L2 205 select RADIO_ISA 206 ---help--- 207 Choose Y here if you have one of these FM radio cards, and then fill 208 in the port address below. 209 210 Note that newer AIMSlab RadioTrack cards have a different chipset 211 and are not supported by this driver. For these cards, use the 212 RadioTrack II driver below. 213 214 If you have a GemTeks combined (PnP) sound- and radio card you must 215 use this driver as a module and setup the card with isapnptools. 216 You must also pass the module a suitable io parameter, 0x248 has 217 been reported to be used by these cards. 218 219 More information is contained in the file 220 <file:Documentation/video4linux/radiotrack.txt>. 221 222 To compile this driver as a module, choose M here: the 223 module will be called radio-aimslab. 224 225config RADIO_RTRACK_PORT 226 hex "RadioTrack i/o port (0x20f or 0x30f)" 227 depends on RADIO_RTRACK=y 228 default "30f" 229 help 230 Enter either 0x30f or 0x20f here. The card default is 0x30f, if you 231 haven't changed the jumper setting on the card. 232 233config RADIO_RTRACK2 234 tristate "AIMSlab RadioTrack II support" 235 depends on ISA && VIDEO_V4L2 236 select RADIO_ISA 237 ---help--- 238 Choose Y here if you have this FM radio card, and then fill in the 239 port address below. 240 241 Note: this driver hasn't been tested since a long time due to lack 242 of hardware. If you have this hardware, then please contact the 243 linux-media mailinglist. 244 245 To compile this driver as a module, choose M here: the 246 module will be called radio-rtrack2. 247 248config RADIO_RTRACK2_PORT 249 hex "RadioTrack II i/o port (0x20c or 0x30c)" 250 depends on RADIO_RTRACK2=y 251 default "30c" 252 help 253 Enter either 0x30c or 0x20c here. The card default is 0x30c, if you 254 haven't changed the jumper setting on the card. 255 256config RADIO_AZTECH 257 tristate "Aztech/Packard Bell Radio" 258 depends on ISA && VIDEO_V4L2 259 select RADIO_ISA 260 ---help--- 261 Choose Y here if you have one of these FM radio cards, and then fill 262 in the port address below. 263 264 To compile this driver as a module, choose M here: the 265 module will be called radio-aztech. 266 267config RADIO_AZTECH_PORT 268 hex "Aztech/Packard Bell I/O port (0x350 or 0x358)" 269 depends on RADIO_AZTECH=y 270 default "350" 271 help 272 Enter either 0x350 or 0x358 here. The card default is 0x350, if you 273 haven't changed the setting of jumper JP3 on the card. Removing the 274 jumper sets the card to 0x358. 275 276config RADIO_GEMTEK 277 tristate "GemTek Radio card (or compatible) support" 278 depends on ISA && VIDEO_V4L2 279 select RADIO_ISA 280 ---help--- 281 Choose Y here if you have this FM radio card, and then fill in the 282 I/O port address and settings below. The following cards either have 283 GemTek Radio tuner or are rebranded GemTek Radio cards: 284 285 - Sound Vision 16 Gold with FM Radio 286 - Typhoon Radio card (some models) 287 - Hama Radio card 288 289 To compile this driver as a module, choose M here: the 290 module will be called radio-gemtek. 291 292config RADIO_GEMTEK_PORT 293 hex "Fixed I/O port (0x20c, 0x30c, 0x24c, 0x34c, 0x248 or 0x28c)" 294 depends on RADIO_GEMTEK=y 295 default "34c" 296 help 297 Enter either 0x20c, 0x30c, 0x24c, 0x34c, 0x248 or 0x28c here. The 298 card default is 0x34c, if you haven't changed the jumper setting 299 on the card. 300 301 On Sound Vision 16 Gold PnP with FM Radio (ESS1869+FM Gemtek), the I/O 302 port is 0x20c, 0x248 or 0x28c. 303 304 If automatic I/O port probing is enabled this port will be used only 305 in case of automatic probing failure, ie. as a fallback. 306 307config RADIO_GEMTEK_PROBE 308 bool "Automatic I/O port probing" 309 depends on RADIO_GEMTEK=y 310 default y 311 help 312 Say Y here to enable automatic probing for GemTek Radio card. The 313 following ports will be probed: 0x20c, 0x30c, 0x24c, 0x34c, 0x248 and 314 0x28c. 315 316config RADIO_MIROPCM20 317 tristate "miroSOUND PCM20 radio" 318 depends on ISA && ISA_DMA_API && VIDEO_V4L2 && SND 319 select SND_ISA 320 select SND_MIRO 321 ---help--- 322 Choose Y here if you have this FM radio card. You also need to enable 323 the ALSA sound system. This choice automatically selects the ALSA 324 sound card driver "Miro miroSOUND PCM1pro/PCM12/PCM20radio" as this 325 is required for the radio-miropcm20. 326 327 In order to control your radio card, you will need to use programs 328 that are compatible with the Video For Linux API. Information on 329 this API and pointers to "v4l" programs may be found at 330 <file:Documentation/video4linux/API.html>. 331 332 To compile this driver as a module, choose M here: the 333 module will be called radio-miropcm20. 334 335config RADIO_SF16FMI 336 tristate "SF16-FMI/SF16-FMP Radio" 337 depends on ISA && VIDEO_V4L2 338 ---help--- 339 Choose Y here if you have one of these FM radio cards. 340 341 In order to control your radio card, you will need to use programs 342 that are compatible with the Video For Linux API. Information on 343 this API and pointers to "v4l" programs may be found at 344 <file:Documentation/video4linux/API.html>. 345 346 To compile this driver as a module, choose M here: the 347 module will be called radio-sf16fmi. 348 349config RADIO_SF16FMR2 350 tristate "SF16FMR2 Radio" 351 depends on ISA && VIDEO_V4L2 && SND 352 ---help--- 353 Choose Y here if you have one of these FM radio cards. 354 355 In order to control your radio card, you will need to use programs 356 that are compatible with the Video For Linux API. Information on 357 this API and pointers to "v4l" programs may be found on the WWW at 358 <http://roadrunner.swansea.uk.linux.org/v4l.shtml>. 359 360 To compile this driver as a module, choose M here: the 361 module will be called radio-sf16fmr2. 362 363config RADIO_TERRATEC 364 tristate "TerraTec ActiveRadio ISA Standalone" 365 depends on ISA && VIDEO_V4L2 366 ---help--- 367 Choose Y here if you have this FM radio card, and then fill in the 368 port address below. (TODO) 369 370 Note: This driver is in its early stages. Right now volume and 371 frequency control and muting works at least for me, but 372 unfortunately I have not found anybody who wants to use this card 373 with Linux. So if it is this what YOU are trying to do right now, 374 PLEASE DROP ME A NOTE!! Rolf Offermanns <rolf@offermanns.de>. 375 376 In order to control your radio card, you will need to use programs 377 that are compatible with the Video For Linux API. Information on 378 this API and pointers to "v4l" programs may be found at 379 <file:Documentation/video4linux/API.html>. 380 381 To compile this driver as a module, choose M here: the 382 module will be called radio-terratec. 383 384config RADIO_TERRATEC_PORT 385 hex "Terratec i/o port (normally 0x590)" 386 depends on RADIO_TERRATEC=y 387 default "590" 388 help 389 Fill in the I/O port of your TerraTec FM radio card. If unsure, go 390 with the default. 391 392config RADIO_TRUST 393 tristate "Trust FM radio card" 394 depends on ISA && VIDEO_V4L2 395 help 396 This is a driver for the Trust FM radio cards. Say Y if you have 397 such a card and want to use it under Linux. 398 399 To compile this driver as a module, choose M here: the 400 module will be called radio-trust. 401 402config RADIO_TRUST_PORT 403 hex "Trust i/o port (usually 0x350 or 0x358)" 404 depends on RADIO_TRUST=y 405 default "350" 406 help 407 Enter the I/O port of your Trust FM radio card. If unsure, try the 408 values "0x350" or "0x358". 409 410config RADIO_TYPHOON 411 tristate "Typhoon Radio (a.k.a. EcoRadio)" 412 depends on ISA && VIDEO_V4L2 413 ---help--- 414 Choose Y here if you have one of these FM radio cards, and then fill 415 in the port address and the frequency used for muting below. 416 417 In order to control your radio card, you will need to use programs 418 that are compatible with the Video For Linux API. Information on 419 this API and pointers to "v4l" programs may be found at 420 <file:Documentation/video4linux/API.html>. 421 422 To compile this driver as a module, choose M here: the 423 module will be called radio-typhoon. 424 425config RADIO_TYPHOON_PORT 426 hex "Typhoon I/O port (0x316 or 0x336)" 427 depends on RADIO_TYPHOON=y 428 default "316" 429 help 430 Enter the I/O port of your Typhoon or EcoRadio radio card. 431 432config RADIO_TYPHOON_MUTEFREQ 433 int "Typhoon frequency set when muting the device (kHz)" 434 depends on RADIO_TYPHOON=y 435 default "87500" 436 help 437 Enter the frequency used for muting the radio. The device is never 438 completely silent. If the volume is just turned down, you can still 439 hear silent voices and music. For that reason, the frequency of the 440 radio device is set to the frequency you can enter here whenever 441 the device is muted. There should be no local radio station at that 442 frequency. 443 444config RADIO_ZOLTRIX 445 tristate "Zoltrix Radio" 446 depends on ISA && VIDEO_V4L2 447 ---help--- 448 Choose Y here if you have one of these FM radio cards, and then fill 449 in the port address below. 450 451 In order to control your radio card, you will need to use programs 452 that are compatible with the Video For Linux API. Information on 453 this API and pointers to "v4l" programs may be found at 454 <file:Documentation/video4linux/API.html>. 455 456 To compile this driver as a module, choose M here: the 457 module will be called radio-zoltrix. 458 459config RADIO_ZOLTRIX_PORT 460 hex "ZOLTRIX I/O port (0x20c or 0x30c)" 461 depends on RADIO_ZOLTRIX=y 462 default "20c" 463 help 464 Enter the I/O port of your Zoltrix radio card. 465 466endif # V4L_RADIO_ISA_DRIVERS 467 468endif # RADIO_ADAPTERS 469