1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * ispcsiphy.c 4 * 5 * TI OMAP3 ISP - CSI PHY module 6 * 7 * Copyright (C) 2010 Nokia Corporation 8 * Copyright (C) 2009 Texas Instruments, Inc. 9 * 10 * Contacts: Laurent Pinchart <laurent.pinchart@ideasonboard.com> 11 * Sakari Ailus <sakari.ailus@iki.fi> 12 */ 13 14 #include <linux/delay.h> 15 #include <linux/device.h> 16 #include <linux/regmap.h> 17 #include <linux/regulator/consumer.h> 18 19 #include "isp.h" 20 #include "ispreg.h" 21 #include "ispcsiphy.h" 22 23 static void csiphy_routing_cfg_3630(struct isp_csiphy *phy, 24 enum isp_interface_type iface, 25 bool ccp2_strobe) 26 { 27 u32 reg; 28 u32 shift, mode; 29 30 regmap_read(phy->isp->syscon, phy->isp->syscon_offset, ®); 31 32 switch (iface) { 33 default: 34 /* Should not happen in practice, but let's keep the compiler happy. */ 35 return; 36 case ISP_INTERFACE_CCP2B_PHY1: 37 reg &= ~OMAP3630_CONTROL_CAMERA_PHY_CTRL_CSI1_RX_SEL_PHY2; 38 shift = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_PHY1_SHIFT; 39 break; 40 case ISP_INTERFACE_CSI2C_PHY1: 41 shift = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_PHY1_SHIFT; 42 mode = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_DPHY; 43 break; 44 case ISP_INTERFACE_CCP2B_PHY2: 45 reg |= OMAP3630_CONTROL_CAMERA_PHY_CTRL_CSI1_RX_SEL_PHY2; 46 shift = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_PHY2_SHIFT; 47 break; 48 case ISP_INTERFACE_CSI2A_PHY2: 49 shift = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_PHY2_SHIFT; 50 mode = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_DPHY; 51 break; 52 } 53 54 /* Select data/clock or data/strobe mode for CCP2 */ 55 if (iface == ISP_INTERFACE_CCP2B_PHY1 || 56 iface == ISP_INTERFACE_CCP2B_PHY2) { 57 if (ccp2_strobe) 58 mode = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_CCP2_DATA_STROBE; 59 else 60 mode = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_CCP2_DATA_CLOCK; 61 } 62 63 reg &= ~(OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_MASK << shift); 64 reg |= mode << shift; 65 66 regmap_write(phy->isp->syscon, phy->isp->syscon_offset, reg); 67 } 68 69 static void csiphy_routing_cfg_3430(struct isp_csiphy *phy, u32 iface, bool on, 70 bool ccp2_strobe) 71 { 72 u32 csirxfe = OMAP343X_CONTROL_CSIRXFE_PWRDNZ 73 | OMAP343X_CONTROL_CSIRXFE_RESET; 74 75 /* Only the CCP2B on PHY1 is configurable. */ 76 if (iface != ISP_INTERFACE_CCP2B_PHY1) 77 return; 78 79 if (!on) { 80 regmap_write(phy->isp->syscon, phy->isp->syscon_offset, 0); 81 return; 82 } 83 84 if (ccp2_strobe) 85 csirxfe |= OMAP343X_CONTROL_CSIRXFE_SELFORM; 86 87 regmap_write(phy->isp->syscon, phy->isp->syscon_offset, csirxfe); 88 } 89 90 /* 91 * Configure OMAP 3 CSI PHY routing. 92 * @phy: relevant phy device 93 * @iface: ISP_INTERFACE_* 94 * @on: power on or off 95 * @ccp2_strobe: false: data/clock, true: data/strobe 96 * 97 * Note that the underlying routing configuration registers are part of the 98 * control (SCM) register space and part of the CORE power domain on both 3430 99 * and 3630, so they will not hold their contents in off-mode. This isn't an 100 * issue since the MPU power domain is forced on whilst the ISP is in use. 101 */ 102 static void csiphy_routing_cfg(struct isp_csiphy *phy, 103 enum isp_interface_type iface, bool on, 104 bool ccp2_strobe) 105 { 106 if (phy->isp->phy_type == ISP_PHY_TYPE_3630 && on) 107 return csiphy_routing_cfg_3630(phy, iface, ccp2_strobe); 108 if (phy->isp->phy_type == ISP_PHY_TYPE_3430) 109 return csiphy_routing_cfg_3430(phy, iface, on, ccp2_strobe); 110 } 111 112 /* 113 * csiphy_power_autoswitch_enable 114 * @enable: Sets or clears the autoswitch function enable flag. 115 */ 116 static void csiphy_power_autoswitch_enable(struct isp_csiphy *phy, bool enable) 117 { 118 isp_reg_clr_set(phy->isp, phy->cfg_regs, ISPCSI2_PHY_CFG, 119 ISPCSI2_PHY_CFG_PWR_AUTO, 120 enable ? ISPCSI2_PHY_CFG_PWR_AUTO : 0); 121 } 122 123 /* 124 * csiphy_set_power 125 * @power: Power state to be set. 126 * 127 * Returns 0 if successful, or -EBUSY if the retry count is exceeded. 128 */ 129 static int csiphy_set_power(struct isp_csiphy *phy, u32 power) 130 { 131 u32 reg; 132 u8 retry_count; 133 134 isp_reg_clr_set(phy->isp, phy->cfg_regs, ISPCSI2_PHY_CFG, 135 ISPCSI2_PHY_CFG_PWR_CMD_MASK, power); 136 137 retry_count = 0; 138 do { 139 udelay(50); 140 reg = isp_reg_readl(phy->isp, phy->cfg_regs, ISPCSI2_PHY_CFG) & 141 ISPCSI2_PHY_CFG_PWR_STATUS_MASK; 142 143 if (reg != power >> 2) 144 retry_count++; 145 146 } while ((reg != power >> 2) && (retry_count < 100)); 147 148 if (retry_count == 100) { 149 dev_err(phy->isp->dev, "CSI2 CIO set power failed!\n"); 150 return -EBUSY; 151 } 152 153 return 0; 154 } 155 156 /* 157 * TCLK values are OK at their reset values 158 */ 159 #define TCLK_TERM 0 160 #define TCLK_MISS 1 161 #define TCLK_SETTLE 14 162 163 static int omap3isp_csiphy_config(struct isp_csiphy *phy) 164 { 165 struct isp_pipeline *pipe = to_isp_pipeline(phy->entity); 166 struct isp_bus_cfg *buscfg; 167 struct isp_csiphy_lanes_cfg *lanes; 168 int csi2_ddrclk_khz; 169 unsigned int num_data_lanes, used_lanes = 0; 170 unsigned int i; 171 u32 reg; 172 173 buscfg = v4l2_subdev_to_bus_cfg(pipe->external); 174 if (WARN_ON(!buscfg)) 175 return -EPIPE; 176 177 if (buscfg->interface == ISP_INTERFACE_CCP2B_PHY1 178 || buscfg->interface == ISP_INTERFACE_CCP2B_PHY2) { 179 lanes = &buscfg->bus.ccp2.lanecfg; 180 num_data_lanes = 1; 181 } else { 182 lanes = &buscfg->bus.csi2.lanecfg; 183 num_data_lanes = buscfg->bus.csi2.num_data_lanes; 184 } 185 186 if (num_data_lanes > phy->num_data_lanes) 187 return -EINVAL; 188 189 /* Clock and data lanes verification */ 190 for (i = 0; i < num_data_lanes; i++) { 191 if (lanes->data[i].pol > 1 || lanes->data[i].pos > 3) 192 return -EINVAL; 193 194 if (used_lanes & (1 << lanes->data[i].pos)) 195 return -EINVAL; 196 197 used_lanes |= 1 << lanes->data[i].pos; 198 } 199 200 if (lanes->clk.pol > 1 || lanes->clk.pos > 3) 201 return -EINVAL; 202 203 if (lanes->clk.pos == 0 || used_lanes & (1 << lanes->clk.pos)) 204 return -EINVAL; 205 206 /* 207 * The PHY configuration is lost in off mode, that's not an 208 * issue since the MPU power domain is forced on whilst the 209 * ISP is in use. 210 */ 211 csiphy_routing_cfg(phy, buscfg->interface, true, 212 buscfg->bus.ccp2.phy_layer); 213 214 /* DPHY timing configuration */ 215 /* CSI-2 is DDR and we only count used lanes. */ 216 csi2_ddrclk_khz = pipe->external_rate / 1000 217 / (2 * hweight32(used_lanes)) * pipe->external_width; 218 219 reg = isp_reg_readl(phy->isp, phy->phy_regs, ISPCSIPHY_REG0); 220 221 reg &= ~(ISPCSIPHY_REG0_THS_TERM_MASK | 222 ISPCSIPHY_REG0_THS_SETTLE_MASK); 223 /* THS_TERM: Programmed value = ceil(12.5 ns/DDRClk period) - 1. */ 224 reg |= (DIV_ROUND_UP(25 * csi2_ddrclk_khz, 2000000) - 1) 225 << ISPCSIPHY_REG0_THS_TERM_SHIFT; 226 /* THS_SETTLE: Programmed value = ceil(90 ns/DDRClk period) + 3. */ 227 reg |= (DIV_ROUND_UP(90 * csi2_ddrclk_khz, 1000000) + 3) 228 << ISPCSIPHY_REG0_THS_SETTLE_SHIFT; 229 230 isp_reg_writel(phy->isp, reg, phy->phy_regs, ISPCSIPHY_REG0); 231 232 reg = isp_reg_readl(phy->isp, phy->phy_regs, ISPCSIPHY_REG1); 233 234 reg &= ~(ISPCSIPHY_REG1_TCLK_TERM_MASK | 235 ISPCSIPHY_REG1_TCLK_MISS_MASK | 236 ISPCSIPHY_REG1_TCLK_SETTLE_MASK); 237 reg |= TCLK_TERM << ISPCSIPHY_REG1_TCLK_TERM_SHIFT; 238 reg |= TCLK_MISS << ISPCSIPHY_REG1_TCLK_MISS_SHIFT; 239 reg |= TCLK_SETTLE << ISPCSIPHY_REG1_TCLK_SETTLE_SHIFT; 240 241 isp_reg_writel(phy->isp, reg, phy->phy_regs, ISPCSIPHY_REG1); 242 243 /* DPHY lane configuration */ 244 reg = isp_reg_readl(phy->isp, phy->cfg_regs, ISPCSI2_PHY_CFG); 245 246 for (i = 0; i < num_data_lanes; i++) { 247 reg &= ~(ISPCSI2_PHY_CFG_DATA_POL_MASK(i + 1) | 248 ISPCSI2_PHY_CFG_DATA_POSITION_MASK(i + 1)); 249 reg |= (lanes->data[i].pol << 250 ISPCSI2_PHY_CFG_DATA_POL_SHIFT(i + 1)); 251 reg |= (lanes->data[i].pos << 252 ISPCSI2_PHY_CFG_DATA_POSITION_SHIFT(i + 1)); 253 } 254 255 reg &= ~(ISPCSI2_PHY_CFG_CLOCK_POL_MASK | 256 ISPCSI2_PHY_CFG_CLOCK_POSITION_MASK); 257 reg |= lanes->clk.pol << ISPCSI2_PHY_CFG_CLOCK_POL_SHIFT; 258 reg |= lanes->clk.pos << ISPCSI2_PHY_CFG_CLOCK_POSITION_SHIFT; 259 260 isp_reg_writel(phy->isp, reg, phy->cfg_regs, ISPCSI2_PHY_CFG); 261 262 return 0; 263 } 264 265 int omap3isp_csiphy_acquire(struct isp_csiphy *phy, struct media_entity *entity) 266 { 267 int rval; 268 269 if (phy->vdd == NULL) { 270 dev_err(phy->isp->dev, 271 "Power regulator for CSI PHY not available\n"); 272 return -ENODEV; 273 } 274 275 mutex_lock(&phy->mutex); 276 277 rval = regulator_enable(phy->vdd); 278 if (rval < 0) 279 goto done; 280 281 rval = omap3isp_csi2_reset(phy->csi2); 282 if (rval < 0) 283 goto done; 284 285 phy->entity = entity; 286 287 rval = omap3isp_csiphy_config(phy); 288 if (rval < 0) 289 goto done; 290 291 if (phy->isp->revision == ISP_REVISION_15_0) { 292 rval = csiphy_set_power(phy, ISPCSI2_PHY_CFG_PWR_CMD_ON); 293 if (rval) { 294 regulator_disable(phy->vdd); 295 goto done; 296 } 297 298 csiphy_power_autoswitch_enable(phy, true); 299 } 300 done: 301 if (rval < 0) 302 phy->entity = NULL; 303 304 mutex_unlock(&phy->mutex); 305 return rval; 306 } 307 308 void omap3isp_csiphy_release(struct isp_csiphy *phy) 309 { 310 mutex_lock(&phy->mutex); 311 if (phy->entity) { 312 struct isp_pipeline *pipe = to_isp_pipeline(phy->entity); 313 struct isp_bus_cfg *buscfg; 314 315 buscfg = v4l2_subdev_to_bus_cfg(pipe->external); 316 if (WARN_ON(!buscfg)) { 317 mutex_unlock(&phy->mutex); 318 return; 319 } 320 321 csiphy_routing_cfg(phy, buscfg->interface, false, 322 buscfg->bus.ccp2.phy_layer); 323 if (phy->isp->revision == ISP_REVISION_15_0) { 324 csiphy_power_autoswitch_enable(phy, false); 325 csiphy_set_power(phy, ISPCSI2_PHY_CFG_PWR_CMD_OFF); 326 } 327 regulator_disable(phy->vdd); 328 phy->entity = NULL; 329 } 330 mutex_unlock(&phy->mutex); 331 } 332 333 /* 334 * omap3isp_csiphy_init - Initialize the CSI PHY frontends 335 */ 336 int omap3isp_csiphy_init(struct isp_device *isp) 337 { 338 struct isp_csiphy *phy1 = &isp->isp_csiphy1; 339 struct isp_csiphy *phy2 = &isp->isp_csiphy2; 340 341 phy2->isp = isp; 342 phy2->csi2 = &isp->isp_csi2a; 343 phy2->num_data_lanes = ISP_CSIPHY2_NUM_DATA_LANES; 344 phy2->cfg_regs = OMAP3_ISP_IOMEM_CSI2A_REGS1; 345 phy2->phy_regs = OMAP3_ISP_IOMEM_CSIPHY2; 346 mutex_init(&phy2->mutex); 347 348 phy1->isp = isp; 349 mutex_init(&phy1->mutex); 350 351 if (isp->revision == ISP_REVISION_15_0) { 352 phy1->csi2 = &isp->isp_csi2c; 353 phy1->num_data_lanes = ISP_CSIPHY1_NUM_DATA_LANES; 354 phy1->cfg_regs = OMAP3_ISP_IOMEM_CSI2C_REGS1; 355 phy1->phy_regs = OMAP3_ISP_IOMEM_CSIPHY1; 356 } 357 358 return 0; 359 } 360 361 void omap3isp_csiphy_cleanup(struct isp_device *isp) 362 { 363 mutex_destroy(&isp->isp_csiphy1.mutex); 364 mutex_destroy(&isp->isp_csiphy2.mutex); 365 } 366