1 /* 2 * cx18 firmware functions 3 * 4 * Copyright (C) 2007 Hans Verkuil <hverkuil@xs4all.nl> 5 * Copyright (C) 2008 Andy Walls <awalls@md.metrocast.net> 6 * 7 * This program is free software; you can redistribute it and/or modify 8 * it under the terms of the GNU General Public License as published by 9 * the Free Software Foundation; either version 2 of the License, or 10 * (at your option) any later version. 11 * 12 * This program is distributed in the hope that it will be useful, 13 * but WITHOUT ANY WARRANTY; without even the implied warranty of 14 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 15 * GNU General Public License for more details. 16 * 17 * You should have received a copy of the GNU General Public License 18 * along with this program; if not, write to the Free Software 19 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 20 * 02111-1307 USA 21 */ 22 23 #include "cx18-driver.h" 24 #include "cx18-io.h" 25 #include "cx18-scb.h" 26 #include "cx18-irq.h" 27 #include "cx18-firmware.h" 28 #include "cx18-cards.h" 29 #include <linux/firmware.h> 30 31 #define CX18_PROC_SOFT_RESET 0xc70010 32 #define CX18_DDR_SOFT_RESET 0xc70014 33 #define CX18_CLOCK_SELECT1 0xc71000 34 #define CX18_CLOCK_SELECT2 0xc71004 35 #define CX18_HALF_CLOCK_SELECT1 0xc71008 36 #define CX18_HALF_CLOCK_SELECT2 0xc7100C 37 #define CX18_CLOCK_POLARITY1 0xc71010 38 #define CX18_CLOCK_POLARITY2 0xc71014 39 #define CX18_ADD_DELAY_ENABLE1 0xc71018 40 #define CX18_ADD_DELAY_ENABLE2 0xc7101C 41 #define CX18_CLOCK_ENABLE1 0xc71020 42 #define CX18_CLOCK_ENABLE2 0xc71024 43 44 #define CX18_REG_BUS_TIMEOUT_EN 0xc72024 45 46 #define CX18_FAST_CLOCK_PLL_INT 0xc78000 47 #define CX18_FAST_CLOCK_PLL_FRAC 0xc78004 48 #define CX18_FAST_CLOCK_PLL_POST 0xc78008 49 #define CX18_FAST_CLOCK_PLL_PRESCALE 0xc7800C 50 #define CX18_FAST_CLOCK_PLL_ADJUST_BANDWIDTH 0xc78010 51 52 #define CX18_SLOW_CLOCK_PLL_INT 0xc78014 53 #define CX18_SLOW_CLOCK_PLL_FRAC 0xc78018 54 #define CX18_SLOW_CLOCK_PLL_POST 0xc7801C 55 #define CX18_MPEG_CLOCK_PLL_INT 0xc78040 56 #define CX18_MPEG_CLOCK_PLL_FRAC 0xc78044 57 #define CX18_MPEG_CLOCK_PLL_POST 0xc78048 58 #define CX18_PLL_POWER_DOWN 0xc78088 59 #define CX18_SW1_INT_STATUS 0xc73104 60 #define CX18_SW1_INT_ENABLE_PCI 0xc7311C 61 #define CX18_SW2_INT_SET 0xc73140 62 #define CX18_SW2_INT_STATUS 0xc73144 63 #define CX18_ADEC_CONTROL 0xc78120 64 65 #define CX18_DDR_REQUEST_ENABLE 0xc80000 66 #define CX18_DDR_CHIP_CONFIG 0xc80004 67 #define CX18_DDR_REFRESH 0xc80008 68 #define CX18_DDR_TIMING1 0xc8000C 69 #define CX18_DDR_TIMING2 0xc80010 70 #define CX18_DDR_POWER_REG 0xc8001C 71 72 #define CX18_DDR_TUNE_LANE 0xc80048 73 #define CX18_DDR_INITIAL_EMRS 0xc80054 74 #define CX18_DDR_MB_PER_ROW_7 0xc8009C 75 #define CX18_DDR_BASE_63_ADDR 0xc804FC 76 77 #define CX18_WMB_CLIENT02 0xc90108 78 #define CX18_WMB_CLIENT05 0xc90114 79 #define CX18_WMB_CLIENT06 0xc90118 80 #define CX18_WMB_CLIENT07 0xc9011C 81 #define CX18_WMB_CLIENT08 0xc90120 82 #define CX18_WMB_CLIENT09 0xc90124 83 #define CX18_WMB_CLIENT10 0xc90128 84 #define CX18_WMB_CLIENT11 0xc9012C 85 #define CX18_WMB_CLIENT12 0xc90130 86 #define CX18_WMB_CLIENT13 0xc90134 87 #define CX18_WMB_CLIENT14 0xc90138 88 89 #define CX18_DSP0_INTERRUPT_MASK 0xd0004C 90 91 #define APU_ROM_SYNC1 0x6D676553 /* "mgeS" */ 92 #define APU_ROM_SYNC2 0x72646548 /* "rdeH" */ 93 94 struct cx18_apu_rom_seghdr { 95 u32 sync1; 96 u32 sync2; 97 u32 addr; 98 u32 size; 99 }; 100 101 static int load_cpu_fw_direct(const char *fn, u8 __iomem *mem, struct cx18 *cx) 102 { 103 const struct firmware *fw = NULL; 104 int i, j; 105 unsigned size; 106 u32 __iomem *dst = (u32 __iomem *)mem; 107 const u32 *src; 108 109 if (request_firmware(&fw, fn, &cx->pci_dev->dev)) { 110 CX18_ERR("Unable to open firmware %s\n", fn); 111 CX18_ERR("Did you put the firmware in the hotplug firmware directory?\n"); 112 return -ENOMEM; 113 } 114 115 src = (const u32 *)fw->data; 116 117 for (i = 0; i < fw->size; i += 4096) { 118 cx18_setup_page(cx, i); 119 for (j = i; j < fw->size && j < i + 4096; j += 4) { 120 /* no need for endianness conversion on the ppc */ 121 cx18_raw_writel(cx, *src, dst); 122 if (cx18_raw_readl(cx, dst) != *src) { 123 CX18_ERR("Mismatch at offset %x\n", i); 124 release_firmware(fw); 125 cx18_setup_page(cx, 0); 126 return -EIO; 127 } 128 dst++; 129 src++; 130 } 131 } 132 if (!test_bit(CX18_F_I_LOADED_FW, &cx->i_flags)) 133 CX18_INFO("loaded %s firmware (%zu bytes)\n", fn, fw->size); 134 size = fw->size; 135 release_firmware(fw); 136 cx18_setup_page(cx, SCB_OFFSET); 137 return size; 138 } 139 140 static int load_apu_fw_direct(const char *fn, u8 __iomem *dst, struct cx18 *cx, 141 u32 *entry_addr) 142 { 143 const struct firmware *fw = NULL; 144 int i, j; 145 unsigned size; 146 const u32 *src; 147 struct cx18_apu_rom_seghdr seghdr; 148 const u8 *vers; 149 u32 offset = 0; 150 u32 apu_version = 0; 151 int sz; 152 153 if (request_firmware(&fw, fn, &cx->pci_dev->dev)) { 154 CX18_ERR("unable to open firmware %s\n", fn); 155 CX18_ERR("did you put the firmware in the hotplug firmware directory?\n"); 156 cx18_setup_page(cx, 0); 157 return -ENOMEM; 158 } 159 160 *entry_addr = 0; 161 src = (const u32 *)fw->data; 162 vers = fw->data + sizeof(seghdr); 163 sz = fw->size; 164 165 apu_version = (vers[0] << 24) | (vers[4] << 16) | vers[32]; 166 while (offset + sizeof(seghdr) < fw->size) { 167 const __le32 *shptr = (__force __le32 *)src + offset / 4; 168 169 seghdr.sync1 = le32_to_cpu(shptr[0]); 170 seghdr.sync2 = le32_to_cpu(shptr[1]); 171 seghdr.addr = le32_to_cpu(shptr[2]); 172 seghdr.size = le32_to_cpu(shptr[3]); 173 174 offset += sizeof(seghdr); 175 if (seghdr.sync1 != APU_ROM_SYNC1 || 176 seghdr.sync2 != APU_ROM_SYNC2) { 177 offset += seghdr.size; 178 continue; 179 } 180 CX18_DEBUG_INFO("load segment %x-%x\n", seghdr.addr, 181 seghdr.addr + seghdr.size - 1); 182 if (*entry_addr == 0) 183 *entry_addr = seghdr.addr; 184 if (offset + seghdr.size > sz) 185 break; 186 for (i = 0; i < seghdr.size; i += 4096) { 187 cx18_setup_page(cx, seghdr.addr + i); 188 for (j = i; j < seghdr.size && j < i + 4096; j += 4) { 189 /* no need for endianness conversion on the ppc */ 190 cx18_raw_writel(cx, src[(offset + j) / 4], 191 dst + seghdr.addr + j); 192 if (cx18_raw_readl(cx, dst + seghdr.addr + j) 193 != src[(offset + j) / 4]) { 194 CX18_ERR("Mismatch at offset %x\n", 195 offset + j); 196 release_firmware(fw); 197 cx18_setup_page(cx, 0); 198 return -EIO; 199 } 200 } 201 } 202 offset += seghdr.size; 203 } 204 if (!test_bit(CX18_F_I_LOADED_FW, &cx->i_flags)) 205 CX18_INFO("loaded %s firmware V%08x (%zu bytes)\n", 206 fn, apu_version, fw->size); 207 size = fw->size; 208 release_firmware(fw); 209 cx18_setup_page(cx, 0); 210 return size; 211 } 212 213 void cx18_halt_firmware(struct cx18 *cx) 214 { 215 CX18_DEBUG_INFO("Preparing for firmware halt.\n"); 216 cx18_write_reg_expect(cx, 0x000F000F, CX18_PROC_SOFT_RESET, 217 0x0000000F, 0x000F000F); 218 cx18_write_reg_expect(cx, 0x00020002, CX18_ADEC_CONTROL, 219 0x00000002, 0x00020002); 220 } 221 222 void cx18_init_power(struct cx18 *cx, int lowpwr) 223 { 224 /* power-down Spare and AOM PLLs */ 225 /* power-up fast, slow and mpeg PLLs */ 226 cx18_write_reg(cx, 0x00000008, CX18_PLL_POWER_DOWN); 227 228 /* ADEC out of sleep */ 229 cx18_write_reg_expect(cx, 0x00020000, CX18_ADEC_CONTROL, 230 0x00000000, 0x00020002); 231 232 /* 233 * The PLL parameters are based on the external crystal frequency that 234 * would ideally be: 235 * 236 * NTSC Color subcarrier freq * 8 = 237 * 4.5 MHz/286 * 455/2 * 8 = 28.63636363... MHz 238 * 239 * The accidents of history and rationale that explain from where this 240 * combination of magic numbers originate can be found in: 241 * 242 * [1] Abrahams, I. C., "Choice of Chrominance Subcarrier Frequency in 243 * the NTSC Standards", Proceedings of the I-R-E, January 1954, pp 79-80 244 * 245 * [2] Abrahams, I. C., "The 'Frequency Interleaving' Principle in the 246 * NTSC Standards", Proceedings of the I-R-E, January 1954, pp 81-83 247 * 248 * As Mike Bradley has rightly pointed out, it's not the exact crystal 249 * frequency that matters, only that all parts of the driver and 250 * firmware are using the same value (close to the ideal value). 251 * 252 * Since I have a strong suspicion that, if the firmware ever assumes a 253 * crystal value at all, it will assume 28.636360 MHz, the crystal 254 * freq used in calculations in this driver will be: 255 * 256 * xtal_freq = 28.636360 MHz 257 * 258 * an error of less than 0.13 ppm which is way, way better than any off 259 * the shelf crystal will have for accuracy anyway. 260 * 261 * Below I aim to run the PLLs' VCOs near 400 MHz to minimze errors. 262 * 263 * Many thanks to Jeff Campbell and Mike Bradley for their extensive 264 * investigation, experimentation, testing, and suggested solutions of 265 * of audio/video sync problems with SVideo and CVBS captures. 266 */ 267 268 /* the fast clock is at 200/245 MHz */ 269 /* 1 * xtal_freq * 0x0d.f7df9b8 / 2 = 200 MHz: 400 MHz pre post-divide*/ 270 /* 1 * xtal_freq * 0x11.1c71eb8 / 2 = 245 MHz: 490 MHz pre post-divide*/ 271 cx18_write_reg(cx, lowpwr ? 0xD : 0x11, CX18_FAST_CLOCK_PLL_INT); 272 cx18_write_reg(cx, lowpwr ? 0x1EFBF37 : 0x038E3D7, 273 CX18_FAST_CLOCK_PLL_FRAC); 274 275 cx18_write_reg(cx, 2, CX18_FAST_CLOCK_PLL_POST); 276 cx18_write_reg(cx, 1, CX18_FAST_CLOCK_PLL_PRESCALE); 277 cx18_write_reg(cx, 4, CX18_FAST_CLOCK_PLL_ADJUST_BANDWIDTH); 278 279 /* set slow clock to 125/120 MHz */ 280 /* xtal_freq * 0x0d.1861a20 / 3 = 125 MHz: 375 MHz before post-divide */ 281 /* xtal_freq * 0x0c.92493f8 / 3 = 120 MHz: 360 MHz before post-divide */ 282 cx18_write_reg(cx, lowpwr ? 0xD : 0xC, CX18_SLOW_CLOCK_PLL_INT); 283 cx18_write_reg(cx, lowpwr ? 0x30C344 : 0x124927F, 284 CX18_SLOW_CLOCK_PLL_FRAC); 285 cx18_write_reg(cx, 3, CX18_SLOW_CLOCK_PLL_POST); 286 287 /* mpeg clock pll 54MHz */ 288 /* xtal_freq * 0xf.15f17f0 / 8 = 54 MHz: 432 MHz before post-divide */ 289 cx18_write_reg(cx, 0xF, CX18_MPEG_CLOCK_PLL_INT); 290 cx18_write_reg(cx, 0x2BE2FE, CX18_MPEG_CLOCK_PLL_FRAC); 291 cx18_write_reg(cx, 8, CX18_MPEG_CLOCK_PLL_POST); 292 293 /* Defaults */ 294 /* APU = SC or SC/2 = 125/62.5 */ 295 /* EPU = SC = 125 */ 296 /* DDR = FC = 180 */ 297 /* ENC = SC = 125 */ 298 /* AI1 = SC = 125 */ 299 /* VIM2 = disabled */ 300 /* PCI = FC/2 = 90 */ 301 /* AI2 = disabled */ 302 /* DEMUX = disabled */ 303 /* AO = SC/2 = 62.5 */ 304 /* SER = 54MHz */ 305 /* VFC = disabled */ 306 /* USB = disabled */ 307 308 if (lowpwr) { 309 cx18_write_reg_expect(cx, 0xFFFF0020, CX18_CLOCK_SELECT1, 310 0x00000020, 0xFFFFFFFF); 311 cx18_write_reg_expect(cx, 0xFFFF0004, CX18_CLOCK_SELECT2, 312 0x00000004, 0xFFFFFFFF); 313 } else { 314 /* This doesn't explicitly set every clock select */ 315 cx18_write_reg_expect(cx, 0x00060004, CX18_CLOCK_SELECT1, 316 0x00000004, 0x00060006); 317 cx18_write_reg_expect(cx, 0x00060006, CX18_CLOCK_SELECT2, 318 0x00000006, 0x00060006); 319 } 320 321 cx18_write_reg_expect(cx, 0xFFFF0002, CX18_HALF_CLOCK_SELECT1, 322 0x00000002, 0xFFFFFFFF); 323 cx18_write_reg_expect(cx, 0xFFFF0104, CX18_HALF_CLOCK_SELECT2, 324 0x00000104, 0xFFFFFFFF); 325 cx18_write_reg_expect(cx, 0xFFFF9026, CX18_CLOCK_ENABLE1, 326 0x00009026, 0xFFFFFFFF); 327 cx18_write_reg_expect(cx, 0xFFFF3105, CX18_CLOCK_ENABLE2, 328 0x00003105, 0xFFFFFFFF); 329 } 330 331 void cx18_init_memory(struct cx18 *cx) 332 { 333 cx18_msleep_timeout(10, 0); 334 cx18_write_reg_expect(cx, 0x00010000, CX18_DDR_SOFT_RESET, 335 0x00000000, 0x00010001); 336 cx18_msleep_timeout(10, 0); 337 338 cx18_write_reg(cx, cx->card->ddr.chip_config, CX18_DDR_CHIP_CONFIG); 339 340 cx18_msleep_timeout(10, 0); 341 342 cx18_write_reg(cx, cx->card->ddr.refresh, CX18_DDR_REFRESH); 343 cx18_write_reg(cx, cx->card->ddr.timing1, CX18_DDR_TIMING1); 344 cx18_write_reg(cx, cx->card->ddr.timing2, CX18_DDR_TIMING2); 345 346 cx18_msleep_timeout(10, 0); 347 348 /* Initialize DQS pad time */ 349 cx18_write_reg(cx, cx->card->ddr.tune_lane, CX18_DDR_TUNE_LANE); 350 cx18_write_reg(cx, cx->card->ddr.initial_emrs, CX18_DDR_INITIAL_EMRS); 351 352 cx18_msleep_timeout(10, 0); 353 354 cx18_write_reg_expect(cx, 0x00020000, CX18_DDR_SOFT_RESET, 355 0x00000000, 0x00020002); 356 cx18_msleep_timeout(10, 0); 357 358 /* use power-down mode when idle */ 359 cx18_write_reg(cx, 0x00000010, CX18_DDR_POWER_REG); 360 361 cx18_write_reg_expect(cx, 0x00010001, CX18_REG_BUS_TIMEOUT_EN, 362 0x00000001, 0x00010001); 363 364 cx18_write_reg(cx, 0x48, CX18_DDR_MB_PER_ROW_7); 365 cx18_write_reg(cx, 0xE0000, CX18_DDR_BASE_63_ADDR); 366 367 cx18_write_reg(cx, 0x00000101, CX18_WMB_CLIENT02); /* AO */ 368 cx18_write_reg(cx, 0x00000101, CX18_WMB_CLIENT09); /* AI2 */ 369 cx18_write_reg(cx, 0x00000101, CX18_WMB_CLIENT05); /* VIM1 */ 370 cx18_write_reg(cx, 0x00000101, CX18_WMB_CLIENT06); /* AI1 */ 371 cx18_write_reg(cx, 0x00000101, CX18_WMB_CLIENT07); /* 3D comb */ 372 cx18_write_reg(cx, 0x00000101, CX18_WMB_CLIENT10); /* ME */ 373 cx18_write_reg(cx, 0x00000101, CX18_WMB_CLIENT12); /* ENC */ 374 cx18_write_reg(cx, 0x00000101, CX18_WMB_CLIENT13); /* PK */ 375 cx18_write_reg(cx, 0x00000101, CX18_WMB_CLIENT11); /* RC */ 376 cx18_write_reg(cx, 0x00000101, CX18_WMB_CLIENT14); /* AVO */ 377 } 378 379 #define CX18_CPU_FIRMWARE "v4l-cx23418-cpu.fw" 380 #define CX18_APU_FIRMWARE "v4l-cx23418-apu.fw" 381 382 int cx18_firmware_init(struct cx18 *cx) 383 { 384 u32 fw_entry_addr; 385 int sz, retries; 386 u32 api_args[MAX_MB_ARGUMENTS]; 387 388 /* Allow chip to control CLKRUN */ 389 cx18_write_reg(cx, 0x5, CX18_DSP0_INTERRUPT_MASK); 390 391 /* Stop the firmware */ 392 cx18_write_reg_expect(cx, 0x000F000F, CX18_PROC_SOFT_RESET, 393 0x0000000F, 0x000F000F); 394 395 cx18_msleep_timeout(1, 0); 396 397 /* If the CPU is still running */ 398 if ((cx18_read_reg(cx, CX18_PROC_SOFT_RESET) & 8) == 0) { 399 CX18_ERR("%s: couldn't stop CPU to load firmware\n", __func__); 400 return -EIO; 401 } 402 403 cx18_sw1_irq_enable(cx, IRQ_CPU_TO_EPU | IRQ_APU_TO_EPU); 404 cx18_sw2_irq_enable(cx, IRQ_CPU_TO_EPU_ACK | IRQ_APU_TO_EPU_ACK); 405 406 sz = load_cpu_fw_direct(CX18_CPU_FIRMWARE, cx->enc_mem, cx); 407 if (sz <= 0) 408 return sz; 409 410 /* The SCB & IPC area *must* be correct before starting the firmwares */ 411 cx18_init_scb(cx); 412 413 fw_entry_addr = 0; 414 sz = load_apu_fw_direct(CX18_APU_FIRMWARE, cx->enc_mem, cx, 415 &fw_entry_addr); 416 if (sz <= 0) 417 return sz; 418 419 /* Start the CPU. The CPU will take care of the APU for us. */ 420 cx18_write_reg_expect(cx, 0x00080000, CX18_PROC_SOFT_RESET, 421 0x00000000, 0x00080008); 422 423 /* Wait up to 500 ms for the APU to come out of reset */ 424 for (retries = 0; 425 retries < 50 && (cx18_read_reg(cx, CX18_PROC_SOFT_RESET) & 1) == 1; 426 retries++) 427 cx18_msleep_timeout(10, 0); 428 429 cx18_msleep_timeout(200, 0); 430 431 if (retries == 50 && 432 (cx18_read_reg(cx, CX18_PROC_SOFT_RESET) & 1) == 1) { 433 CX18_ERR("Could not start the CPU\n"); 434 return -EIO; 435 } 436 437 /* 438 * The CPU had once before set up to receive an interrupt for it's 439 * outgoing IRQ_CPU_TO_EPU_ACK to us. If it ever does this, we get an 440 * interrupt when it sends us an ack, but by the time we process it, 441 * that flag in the SW2 status register has been cleared by the CPU 442 * firmware. We'll prevent that not so useful condition from happening 443 * by clearing the CPU's interrupt enables for Ack IRQ's we want to 444 * process. 445 */ 446 cx18_sw2_irq_disable_cpu(cx, IRQ_CPU_TO_EPU_ACK | IRQ_APU_TO_EPU_ACK); 447 448 /* Try a benign command to see if the CPU is alive and well */ 449 sz = cx18_vapi_result(cx, api_args, CX18_CPU_DEBUG_PEEK32, 1, 0); 450 if (sz < 0) 451 return sz; 452 453 /* initialize GPIO */ 454 cx18_write_reg_expect(cx, 0x14001400, 0xc78110, 0x00001400, 0x14001400); 455 return 0; 456 } 457 458 MODULE_FIRMWARE(CX18_CPU_FIRMWARE); 459 MODULE_FIRMWARE(CX18_APU_FIRMWARE); 460