1 /* 2 3 bttv-cards.c 4 5 this file has configuration informations - card-specific stuff 6 like the big tvcards array for the most part 7 8 Copyright (C) 1996,97,98 Ralph Metzler (rjkm@thp.uni-koeln.de) 9 & Marcus Metzler (mocm@thp.uni-koeln.de) 10 (c) 1999-2001 Gerd Knorr <kraxel@goldbach.in-berlin.de> 11 12 This program is free software; you can redistribute it and/or modify 13 it under the terms of the GNU General Public License as published by 14 the Free Software Foundation; either version 2 of the License, or 15 (at your option) any later version. 16 17 This program is distributed in the hope that it will be useful, 18 but WITHOUT ANY WARRANTY; without even the implied warranty of 19 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 20 GNU General Public License for more details. 21 22 You should have received a copy of the GNU General Public License 23 along with this program; if not, write to the Free Software 24 Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. 25 26 */ 27 28 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt 29 30 #include <linux/delay.h> 31 #include <linux/module.h> 32 #include <linux/kmod.h> 33 #include <linux/init.h> 34 #include <linux/pci.h> 35 #include <linux/vmalloc.h> 36 #include <linux/firmware.h> 37 #include <net/checksum.h> 38 39 #include <asm/unaligned.h> 40 #include <asm/io.h> 41 42 #include "bttvp.h" 43 #include <media/v4l2-common.h> 44 #include <media/tvaudio.h> 45 #include "bttv-audio-hook.h" 46 47 /* fwd decl */ 48 static void boot_msp34xx(struct bttv *btv, int pin); 49 static void hauppauge_eeprom(struct bttv *btv); 50 static void avermedia_eeprom(struct bttv *btv); 51 static void osprey_eeprom(struct bttv *btv, const u8 ee[256]); 52 static void modtec_eeprom(struct bttv *btv); 53 static void init_PXC200(struct bttv *btv); 54 static void init_RTV24(struct bttv *btv); 55 static void init_PCI8604PW(struct bttv *btv); 56 57 static void rv605_muxsel(struct bttv *btv, unsigned int input); 58 static void eagle_muxsel(struct bttv *btv, unsigned int input); 59 static void xguard_muxsel(struct bttv *btv, unsigned int input); 60 static void ivc120_muxsel(struct bttv *btv, unsigned int input); 61 static void gvc1100_muxsel(struct bttv *btv, unsigned int input); 62 63 static void PXC200_muxsel(struct bttv *btv, unsigned int input); 64 65 static void picolo_tetra_muxsel(struct bttv *btv, unsigned int input); 66 static void picolo_tetra_init(struct bttv *btv); 67 68 static void tibetCS16_muxsel(struct bttv *btv, unsigned int input); 69 static void tibetCS16_init(struct bttv *btv); 70 71 static void kodicom4400r_muxsel(struct bttv *btv, unsigned int input); 72 static void kodicom4400r_init(struct bttv *btv); 73 74 static void sigmaSLC_muxsel(struct bttv *btv, unsigned int input); 75 static void sigmaSQ_muxsel(struct bttv *btv, unsigned int input); 76 77 static void geovision_muxsel(struct bttv *btv, unsigned int input); 78 79 static void phytec_muxsel(struct bttv *btv, unsigned int input); 80 81 static void gv800s_muxsel(struct bttv *btv, unsigned int input); 82 static void gv800s_init(struct bttv *btv); 83 84 static void td3116_muxsel(struct bttv *btv, unsigned int input); 85 86 static int terratec_active_radio_upgrade(struct bttv *btv); 87 static int tea5757_read(struct bttv *btv); 88 static int tea5757_write(struct bttv *btv, int value); 89 static void identify_by_eeprom(struct bttv *btv, 90 unsigned char eeprom_data[256]); 91 static int pvr_boot(struct bttv *btv); 92 93 /* config variables */ 94 static unsigned int triton1; 95 static unsigned int vsfx; 96 static unsigned int latency = UNSET; 97 int no_overlay=-1; 98 99 static unsigned int card[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET }; 100 static unsigned int pll[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET }; 101 static unsigned int tuner[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET }; 102 static unsigned int svhs[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET }; 103 static unsigned int remote[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET }; 104 static unsigned int audiodev[BTTV_MAX]; 105 static unsigned int saa6588[BTTV_MAX]; 106 static struct bttv *master[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = NULL }; 107 static unsigned int autoload = UNSET; 108 static unsigned int gpiomask = UNSET; 109 static unsigned int audioall = UNSET; 110 static unsigned int audiomux[5] = { [ 0 ... 4 ] = UNSET }; 111 112 /* insmod options */ 113 module_param(triton1, int, 0444); 114 module_param(vsfx, int, 0444); 115 module_param(no_overlay, int, 0444); 116 module_param(latency, int, 0444); 117 module_param(gpiomask, int, 0444); 118 module_param(audioall, int, 0444); 119 module_param(autoload, int, 0444); 120 121 module_param_array(card, int, NULL, 0444); 122 module_param_array(pll, int, NULL, 0444); 123 module_param_array(tuner, int, NULL, 0444); 124 module_param_array(svhs, int, NULL, 0444); 125 module_param_array(remote, int, NULL, 0444); 126 module_param_array(audiodev, int, NULL, 0444); 127 module_param_array(audiomux, int, NULL, 0444); 128 129 MODULE_PARM_DESC(triton1,"set ETBF pci config bit " 130 "[enable bug compatibility for triton1 + others]"); 131 MODULE_PARM_DESC(vsfx,"set VSFX pci config bit " 132 "[yet another chipset flaw workaround]"); 133 MODULE_PARM_DESC(latency,"pci latency timer"); 134 MODULE_PARM_DESC(card,"specify TV/grabber card model, see CARDLIST file for a list"); 135 MODULE_PARM_DESC(pll, "specify installed crystal (0=none, 28=28 MHz, 35=35 MHz, 14=14 MHz)"); 136 MODULE_PARM_DESC(tuner,"specify installed tuner type"); 137 MODULE_PARM_DESC(autoload, "obsolete option, please do not use anymore"); 138 MODULE_PARM_DESC(audiodev, "specify audio device:\n" 139 "\t\t-1 = no audio\n" 140 "\t\t 0 = autodetect (default)\n" 141 "\t\t 1 = msp3400\n" 142 "\t\t 2 = tda7432\n" 143 "\t\t 3 = tvaudio"); 144 MODULE_PARM_DESC(saa6588, "if 1, then load the saa6588 RDS module, default (0) is to use the card definition."); 145 MODULE_PARM_DESC(no_overlay,"allow override overlay default (0 disables, 1 enables)" 146 " [some VIA/SIS chipsets are known to have problem with overlay]"); 147 148 /* ----------------------------------------------------------------------- */ 149 /* list of card IDs for bt878+ cards */ 150 151 static struct CARD { 152 unsigned id; 153 int cardnr; 154 char *name; 155 } cards[] = { 156 { 0x13eb0070, BTTV_BOARD_HAUPPAUGE878, "Hauppauge WinTV" }, 157 { 0x39000070, BTTV_BOARD_HAUPPAUGE878, "Hauppauge WinTV-D" }, 158 { 0x45000070, BTTV_BOARD_HAUPPAUGEPVR, "Hauppauge WinTV/PVR" }, 159 { 0xff000070, BTTV_BOARD_OSPREY1x0, "Osprey-100" }, 160 { 0xff010070, BTTV_BOARD_OSPREY2x0_SVID,"Osprey-200" }, 161 { 0xff020070, BTTV_BOARD_OSPREY500, "Osprey-500" }, 162 { 0xff030070, BTTV_BOARD_OSPREY2000, "Osprey-2000" }, 163 { 0xff040070, BTTV_BOARD_OSPREY540, "Osprey-540" }, 164 { 0xff070070, BTTV_BOARD_OSPREY440, "Osprey-440" }, 165 166 { 0x00011002, BTTV_BOARD_ATI_TVWONDER, "ATI TV Wonder" }, 167 { 0x00031002, BTTV_BOARD_ATI_TVWONDERVE,"ATI TV Wonder/VE" }, 168 169 { 0x6606107d, BTTV_BOARD_WINFAST2000, "Leadtek WinFast TV 2000" }, 170 { 0x6607107d, BTTV_BOARD_WINFASTVC100, "Leadtek WinFast VC 100" }, 171 { 0x6609107d, BTTV_BOARD_WINFAST2000, "Leadtek TV 2000 XP" }, 172 { 0x263610b4, BTTV_BOARD_STB2, "STB TV PCI FM, Gateway P/N 6000704" }, 173 { 0x264510b4, BTTV_BOARD_STB2, "STB TV PCI FM, Gateway P/N 6000704" }, 174 { 0x402010fc, BTTV_BOARD_GVBCTV3PCI, "I-O Data Co. GV-BCTV3/PCI" }, 175 { 0x405010fc, BTTV_BOARD_GVBCTV4PCI, "I-O Data Co. GV-BCTV4/PCI" }, 176 { 0x407010fc, BTTV_BOARD_GVBCTV5PCI, "I-O Data Co. GV-BCTV5/PCI" }, 177 { 0xd01810fc, BTTV_BOARD_GVBCTV5PCI, "I-O Data Co. GV-BCTV5/PCI" }, 178 179 { 0x001211bd, BTTV_BOARD_PINNACLE, "Pinnacle PCTV" }, 180 /* some cards ship with byteswapped IDs ... */ 181 { 0x1200bd11, BTTV_BOARD_PINNACLE, "Pinnacle PCTV [bswap]" }, 182 { 0xff00bd11, BTTV_BOARD_PINNACLE, "Pinnacle PCTV [bswap]" }, 183 /* this seems to happen as well ... */ 184 { 0xff1211bd, BTTV_BOARD_PINNACLE, "Pinnacle PCTV" }, 185 186 { 0x3000121a, BTTV_BOARD_VOODOOTV_200, "3Dfx VoodooTV 200" }, 187 { 0x263710b4, BTTV_BOARD_VOODOOTV_FM, "3Dfx VoodooTV FM" }, 188 { 0x3060121a, BTTV_BOARD_STB2, "3Dfx VoodooTV 100/ STB OEM" }, 189 190 { 0x3000144f, BTTV_BOARD_MAGICTVIEW063, "(Askey Magic/others) TView99 CPH06x" }, 191 { 0xa005144f, BTTV_BOARD_MAGICTVIEW063, "CPH06X TView99-Card" }, 192 { 0x3002144f, BTTV_BOARD_MAGICTVIEW061, "(Askey Magic/others) TView99 CPH05x" }, 193 { 0x3005144f, BTTV_BOARD_MAGICTVIEW061, "(Askey Magic/others) TView99 CPH061/06L (T1/LC)" }, 194 { 0x5000144f, BTTV_BOARD_MAGICTVIEW061, "Askey CPH050" }, 195 { 0x300014ff, BTTV_BOARD_MAGICTVIEW061, "TView 99 (CPH061)" }, 196 { 0x300214ff, BTTV_BOARD_PHOEBE_TVMAS, "Phoebe TV Master (CPH060)" }, 197 198 { 0x00011461, BTTV_BOARD_AVPHONE98, "AVerMedia TVPhone98" }, 199 { 0x00021461, BTTV_BOARD_AVERMEDIA98, "AVermedia TVCapture 98" }, 200 { 0x00031461, BTTV_BOARD_AVPHONE98, "AVerMedia TVPhone98" }, 201 { 0x00041461, BTTV_BOARD_AVERMEDIA98, "AVerMedia TVCapture 98" }, 202 { 0x03001461, BTTV_BOARD_AVERMEDIA98, "VDOMATE TV TUNER CARD" }, 203 204 { 0x1117153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (Philips PAL B/G)" }, 205 { 0x1118153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (Temic PAL B/G)" }, 206 { 0x1119153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (Philips PAL I)" }, 207 { 0x111a153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (Temic PAL I)" }, 208 209 { 0x1123153b, BTTV_BOARD_TERRATVRADIO, "Terratec TV Radio+" }, 210 { 0x1127153b, BTTV_BOARD_TERRATV, "Terratec TV+ (V1.05)" }, 211 /* clashes with FlyVideo 212 *{ 0x18521852, BTTV_BOARD_TERRATV, "Terratec TV+ (V1.10)" }, */ 213 { 0x1134153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (LR102)" }, 214 { 0x1135153b, BTTV_BOARD_TERRATVALUER, "Terratec TValue Radio" }, /* LR102 */ 215 { 0x5018153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue" }, /* ?? */ 216 { 0xff3b153b, BTTV_BOARD_TERRATVALUER, "Terratec TValue Radio" }, /* ?? */ 217 218 { 0x400015b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV" }, 219 { 0x400a15b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV" }, 220 { 0x400d15b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV / Radio" }, 221 { 0x401015b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV / Radio" }, 222 { 0x401615b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV / Radio" }, 223 224 { 0x1430aa00, BTTV_BOARD_PV143, "Provideo PV143A" }, 225 { 0x1431aa00, BTTV_BOARD_PV143, "Provideo PV143B" }, 226 { 0x1432aa00, BTTV_BOARD_PV143, "Provideo PV143C" }, 227 { 0x1433aa00, BTTV_BOARD_PV143, "Provideo PV143D" }, 228 { 0x1433aa03, BTTV_BOARD_PV143, "Security Eyes" }, 229 230 { 0x1460aa00, BTTV_BOARD_PV150, "Provideo PV150A-1" }, 231 { 0x1461aa01, BTTV_BOARD_PV150, "Provideo PV150A-2" }, 232 { 0x1462aa02, BTTV_BOARD_PV150, "Provideo PV150A-3" }, 233 { 0x1463aa03, BTTV_BOARD_PV150, "Provideo PV150A-4" }, 234 235 { 0x1464aa04, BTTV_BOARD_PV150, "Provideo PV150B-1" }, 236 { 0x1465aa05, BTTV_BOARD_PV150, "Provideo PV150B-2" }, 237 { 0x1466aa06, BTTV_BOARD_PV150, "Provideo PV150B-3" }, 238 { 0x1467aa07, BTTV_BOARD_PV150, "Provideo PV150B-4" }, 239 240 { 0xa132ff00, BTTV_BOARD_IVC100, "IVC-100" }, 241 { 0xa1550000, BTTV_BOARD_IVC200, "IVC-200" }, 242 { 0xa1550001, BTTV_BOARD_IVC200, "IVC-200" }, 243 { 0xa1550002, BTTV_BOARD_IVC200, "IVC-200" }, 244 { 0xa1550003, BTTV_BOARD_IVC200, "IVC-200" }, 245 { 0xa1550100, BTTV_BOARD_IVC200, "IVC-200G" }, 246 { 0xa1550101, BTTV_BOARD_IVC200, "IVC-200G" }, 247 { 0xa1550102, BTTV_BOARD_IVC200, "IVC-200G" }, 248 { 0xa1550103, BTTV_BOARD_IVC200, "IVC-200G" }, 249 { 0xa1550800, BTTV_BOARD_IVC200, "IVC-200" }, 250 { 0xa1550801, BTTV_BOARD_IVC200, "IVC-200" }, 251 { 0xa1550802, BTTV_BOARD_IVC200, "IVC-200" }, 252 { 0xa1550803, BTTV_BOARD_IVC200, "IVC-200" }, 253 { 0xa182ff00, BTTV_BOARD_IVC120, "IVC-120G" }, 254 { 0xa182ff01, BTTV_BOARD_IVC120, "IVC-120G" }, 255 { 0xa182ff02, BTTV_BOARD_IVC120, "IVC-120G" }, 256 { 0xa182ff03, BTTV_BOARD_IVC120, "IVC-120G" }, 257 { 0xa182ff04, BTTV_BOARD_IVC120, "IVC-120G" }, 258 { 0xa182ff05, BTTV_BOARD_IVC120, "IVC-120G" }, 259 { 0xa182ff06, BTTV_BOARD_IVC120, "IVC-120G" }, 260 { 0xa182ff07, BTTV_BOARD_IVC120, "IVC-120G" }, 261 { 0xa182ff08, BTTV_BOARD_IVC120, "IVC-120G" }, 262 { 0xa182ff09, BTTV_BOARD_IVC120, "IVC-120G" }, 263 { 0xa182ff0a, BTTV_BOARD_IVC120, "IVC-120G" }, 264 { 0xa182ff0b, BTTV_BOARD_IVC120, "IVC-120G" }, 265 { 0xa182ff0c, BTTV_BOARD_IVC120, "IVC-120G" }, 266 { 0xa182ff0d, BTTV_BOARD_IVC120, "IVC-120G" }, 267 { 0xa182ff0e, BTTV_BOARD_IVC120, "IVC-120G" }, 268 { 0xa182ff0f, BTTV_BOARD_IVC120, "IVC-120G" }, 269 { 0xf0500000, BTTV_BOARD_IVCE8784, "IVCE-8784" }, 270 { 0xf0500001, BTTV_BOARD_IVCE8784, "IVCE-8784" }, 271 { 0xf0500002, BTTV_BOARD_IVCE8784, "IVCE-8784" }, 272 { 0xf0500003, BTTV_BOARD_IVCE8784, "IVCE-8784" }, 273 274 { 0x41424344, BTTV_BOARD_GRANDTEC, "GrandTec Multi Capture" }, 275 { 0x01020304, BTTV_BOARD_XGUARD, "Grandtec Grand X-Guard" }, 276 277 { 0x18501851, BTTV_BOARD_CHRONOS_VS2, "FlyVideo 98 (LR50)/ Chronos Video Shuttle II" }, 278 { 0xa0501851, BTTV_BOARD_CHRONOS_VS2, "FlyVideo 98 (LR50)/ Chronos Video Shuttle II" }, 279 { 0x18511851, BTTV_BOARD_FLYVIDEO98EZ, "FlyVideo 98EZ (LR51)/ CyberMail AV" }, 280 { 0x18521852, BTTV_BOARD_TYPHOON_TVIEW, "FlyVideo 98FM (LR50)/ Typhoon TView TV/FM Tuner" }, 281 { 0x41a0a051, BTTV_BOARD_FLYVIDEO_98FM, "Lifeview FlyVideo 98 LR50 Rev Q" }, 282 { 0x18501f7f, BTTV_BOARD_FLYVIDEO_98, "Lifeview Flyvideo 98" }, 283 284 { 0x010115cb, BTTV_BOARD_GMV1, "AG GMV1" }, 285 { 0x010114c7, BTTV_BOARD_MODTEC_205, "Modular Technology MM201/MM202/MM205/MM210/MM215 PCTV" }, 286 287 { 0x10b42636, BTTV_BOARD_HAUPPAUGE878, "STB ???" }, 288 { 0x217d6606, BTTV_BOARD_WINFAST2000, "Leadtek WinFast TV 2000" }, 289 { 0xfff6f6ff, BTTV_BOARD_WINFAST2000, "Leadtek WinFast TV 2000" }, 290 { 0x03116000, BTTV_BOARD_SENSORAY311_611, "Sensoray 311" }, 291 { 0x06116000, BTTV_BOARD_SENSORAY311_611, "Sensoray 611" }, 292 { 0x00790e11, BTTV_BOARD_WINDVR, "Canopus WinDVR PCI" }, 293 { 0xa0fca1a0, BTTV_BOARD_ZOLTRIX, "Face to Face Tvmax" }, 294 { 0x82b2aa6a, BTTV_BOARD_SIMUS_GVC1100, "SIMUS GVC1100" }, 295 { 0x146caa0c, BTTV_BOARD_PV951, "ituner spectra8" }, 296 { 0x200a1295, BTTV_BOARD_PXC200, "ImageNation PXC200A" }, 297 298 { 0x40111554, BTTV_BOARD_PV_BT878P_9B, "Prolink Pixelview PV-BT" }, 299 { 0x17de0a01, BTTV_BOARD_KWORLD, "Mecer TV/FM/Video Tuner" }, 300 301 { 0x01051805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #1" }, 302 { 0x01061805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #2" }, 303 { 0x01071805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #3" }, 304 { 0x01081805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #4" }, 305 306 { 0x15409511, BTTV_BOARD_ACORP_Y878F, "Acorp Y878F" }, 307 308 { 0x53534149, BTTV_BOARD_SSAI_SECURITY, "SSAI Security Video Interface" }, 309 { 0x5353414a, BTTV_BOARD_SSAI_ULTRASOUND, "SSAI Ultrasound Video Interface" }, 310 311 /* likely broken, vendor id doesn't match the other magic views ... 312 * { 0xa0fca04f, BTTV_BOARD_MAGICTVIEW063, "Guillemot Maxi TV Video 3" }, */ 313 314 /* Duplicate PCI ID, reconfigure for this board during the eeprom read. 315 * { 0x13eb0070, BTTV_BOARD_HAUPPAUGE_IMPACTVCB, "Hauppauge ImpactVCB" }, */ 316 317 { 0x109e036e, BTTV_BOARD_CONCEPTRONIC_CTVFMI2, "Conceptronic CTVFMi v2"}, 318 319 /* DVB cards (using pci function .1 for mpeg data xfer) */ 320 { 0x001c11bd, BTTV_BOARD_PINNACLESAT, "Pinnacle PCTV Sat" }, 321 { 0x01010071, BTTV_BOARD_NEBULA_DIGITV, "Nebula Electronics DigiTV" }, 322 { 0x20007063, BTTV_BOARD_PC_HDTV, "pcHDTV HD-2000 TV"}, 323 { 0x002611bd, BTTV_BOARD_TWINHAN_DST, "Pinnacle PCTV SAT CI" }, 324 { 0x00011822, BTTV_BOARD_TWINHAN_DST, "Twinhan VisionPlus DVB" }, 325 { 0xfc00270f, BTTV_BOARD_TWINHAN_DST, "ChainTech digitop DST-1000 DVB-S" }, 326 { 0x07711461, BTTV_BOARD_AVDVBT_771, "AVermedia AverTV DVB-T 771" }, 327 { 0x07611461, BTTV_BOARD_AVDVBT_761, "AverMedia AverTV DVB-T 761" }, 328 { 0xdb1018ac, BTTV_BOARD_DVICO_DVBT_LITE, "DViCO FusionHDTV DVB-T Lite" }, 329 { 0xdb1118ac, BTTV_BOARD_DVICO_DVBT_LITE, "Ultraview DVB-T Lite" }, 330 { 0xd50018ac, BTTV_BOARD_DVICO_FUSIONHDTV_5_LITE, "DViCO FusionHDTV 5 Lite" }, 331 { 0x00261822, BTTV_BOARD_TWINHAN_DST, "DNTV Live! Mini "}, 332 { 0xd200dbc0, BTTV_BOARD_DVICO_FUSIONHDTV_2, "DViCO FusionHDTV 2" }, 333 { 0x763c008a, BTTV_BOARD_GEOVISION_GV600, "GeoVision GV-600" }, 334 { 0x18011000, BTTV_BOARD_ENLTV_FM_2, "Encore ENL TV-FM-2" }, 335 { 0x763d800a, BTTV_BOARD_GEOVISION_GV800S, "GeoVision GV-800(S) (master)" }, 336 { 0x763d800b, BTTV_BOARD_GEOVISION_GV800S_SL, "GeoVision GV-800(S) (slave)" }, 337 { 0x763d800c, BTTV_BOARD_GEOVISION_GV800S_SL, "GeoVision GV-800(S) (slave)" }, 338 { 0x763d800d, BTTV_BOARD_GEOVISION_GV800S_SL, "GeoVision GV-800(S) (slave)" }, 339 340 { 0x15401830, BTTV_BOARD_PV183, "Provideo PV183-1" }, 341 { 0x15401831, BTTV_BOARD_PV183, "Provideo PV183-2" }, 342 { 0x15401832, BTTV_BOARD_PV183, "Provideo PV183-3" }, 343 { 0x15401833, BTTV_BOARD_PV183, "Provideo PV183-4" }, 344 { 0x15401834, BTTV_BOARD_PV183, "Provideo PV183-5" }, 345 { 0x15401835, BTTV_BOARD_PV183, "Provideo PV183-6" }, 346 { 0x15401836, BTTV_BOARD_PV183, "Provideo PV183-7" }, 347 { 0x15401837, BTTV_BOARD_PV183, "Provideo PV183-8" }, 348 { 0x3116f200, BTTV_BOARD_TVT_TD3116, "Tongwei Video Technology TD-3116" }, 349 { 0x02280279, BTTV_BOARD_APOSONIC_WDVR, "Aposonic W-DVR" }, 350 { 0, -1, NULL } 351 }; 352 353 /* ----------------------------------------------------------------------- */ 354 /* array with description for bt848 / bt878 tv/grabber cards */ 355 356 struct tvcard bttv_tvcards[] = { 357 /* ---- card 0x00 ---------------------------------- */ 358 [BTTV_BOARD_UNKNOWN] = { 359 .name = " *** UNKNOWN/GENERIC *** ", 360 .video_inputs = 4, 361 .svhs = 2, 362 .muxsel = MUXSEL(2, 3, 1, 0), 363 .tuner_type = UNSET, 364 .tuner_addr = ADDR_UNSET, 365 }, 366 [BTTV_BOARD_MIRO] = { 367 .name = "MIRO PCTV", 368 .video_inputs = 4, 369 /* .audio_inputs= 1, */ 370 .svhs = 2, 371 .gpiomask = 15, 372 .muxsel = MUXSEL(2, 3, 1, 1), 373 .gpiomux = { 2, 0, 0, 0 }, 374 .gpiomute = 10, 375 .tuner_type = UNSET, 376 .tuner_addr = ADDR_UNSET, 377 }, 378 [BTTV_BOARD_HAUPPAUGE] = { 379 .name = "Hauppauge (bt848)", 380 .video_inputs = 4, 381 /* .audio_inputs= 1, */ 382 .svhs = 2, 383 .gpiomask = 7, 384 .muxsel = MUXSEL(2, 3, 1, 1), 385 .gpiomux = { 0, 1, 2, 3 }, 386 .gpiomute = 4, 387 .tuner_type = UNSET, 388 .tuner_addr = ADDR_UNSET, 389 }, 390 [BTTV_BOARD_STB] = { 391 .name = "STB, Gateway P/N 6000699 (bt848)", 392 .video_inputs = 3, 393 /* .audio_inputs= 1, */ 394 .svhs = 2, 395 .gpiomask = 7, 396 .muxsel = MUXSEL(2, 3, 1, 1), 397 .gpiomux = { 4, 0, 2, 3 }, 398 .gpiomute = 1, 399 .no_msp34xx = 1, 400 .tuner_type = TUNER_PHILIPS_NTSC, 401 .tuner_addr = ADDR_UNSET, 402 .pll = PLL_28, 403 .has_radio = 1, 404 }, 405 406 /* ---- card 0x04 ---------------------------------- */ 407 [BTTV_BOARD_INTEL] = { 408 .name = "Intel Create and Share PCI/ Smart Video Recorder III", 409 .video_inputs = 4, 410 /* .audio_inputs= 0, */ 411 .svhs = 2, 412 .gpiomask = 0, 413 .muxsel = MUXSEL(2, 3, 1, 1), 414 .gpiomux = { 0 }, 415 .tuner_type = TUNER_ABSENT, 416 .tuner_addr = ADDR_UNSET, 417 }, 418 [BTTV_BOARD_DIAMOND] = { 419 .name = "Diamond DTV2000", 420 .video_inputs = 4, 421 /* .audio_inputs= 1, */ 422 .svhs = 2, 423 .gpiomask = 3, 424 .muxsel = MUXSEL(2, 3, 1, 0), 425 .gpiomux = { 0, 1, 0, 1 }, 426 .gpiomute = 3, 427 .tuner_type = UNSET, 428 .tuner_addr = ADDR_UNSET, 429 }, 430 [BTTV_BOARD_AVERMEDIA] = { 431 .name = "AVerMedia TVPhone", 432 .video_inputs = 3, 433 /* .audio_inputs= 1, */ 434 .svhs = 3, 435 .muxsel = MUXSEL(2, 3, 1, 1), 436 .gpiomask = 0x0f, 437 .gpiomux = { 0x0c, 0x04, 0x08, 0x04 }, 438 /* 0x04 for some cards ?? */ 439 .tuner_type = UNSET, 440 .tuner_addr = ADDR_UNSET, 441 .audio_mode_gpio= avermedia_tvphone_audio, 442 .has_remote = 1, 443 }, 444 [BTTV_BOARD_MATRIX_VISION] = { 445 .name = "MATRIX-Vision MV-Delta", 446 .video_inputs = 5, 447 /* .audio_inputs= 1, */ 448 .svhs = 3, 449 .gpiomask = 0, 450 .muxsel = MUXSEL(2, 3, 1, 0, 0), 451 .gpiomux = { 0 }, 452 .tuner_type = TUNER_ABSENT, 453 .tuner_addr = ADDR_UNSET, 454 }, 455 456 /* ---- card 0x08 ---------------------------------- */ 457 [BTTV_BOARD_FLYVIDEO] = { 458 .name = "Lifeview FlyVideo II (Bt848) LR26 / MAXI TV Video PCI2 LR26", 459 .video_inputs = 4, 460 /* .audio_inputs= 1, */ 461 .svhs = 2, 462 .gpiomask = 0xc00, 463 .muxsel = MUXSEL(2, 3, 1, 1), 464 .gpiomux = { 0, 0xc00, 0x800, 0x400 }, 465 .gpiomute = 0xc00, 466 .pll = PLL_28, 467 .tuner_type = UNSET, 468 .tuner_addr = ADDR_UNSET, 469 }, 470 [BTTV_BOARD_TURBOTV] = { 471 .name = "IMS/IXmicro TurboTV", 472 .video_inputs = 3, 473 /* .audio_inputs= 1, */ 474 .svhs = 2, 475 .gpiomask = 3, 476 .muxsel = MUXSEL(2, 3, 1, 1), 477 .gpiomux = { 1, 1, 2, 3 }, 478 .pll = PLL_28, 479 .tuner_type = TUNER_TEMIC_PAL, 480 .tuner_addr = ADDR_UNSET, 481 }, 482 [BTTV_BOARD_HAUPPAUGE878] = { 483 .name = "Hauppauge (bt878)", 484 .video_inputs = 4, 485 /* .audio_inputs= 1, */ 486 .svhs = 2, 487 .gpiomask = 0x0f, /* old: 7 */ 488 .muxsel = MUXSEL(2, 0, 1, 1), 489 .gpiomux = { 0, 1, 2, 3 }, 490 .gpiomute = 4, 491 .pll = PLL_28, 492 .tuner_type = UNSET, 493 .tuner_addr = ADDR_UNSET, 494 }, 495 [BTTV_BOARD_MIROPRO] = { 496 .name = "MIRO PCTV pro", 497 .video_inputs = 3, 498 /* .audio_inputs= 1, */ 499 .svhs = 2, 500 .gpiomask = 0x3014f, 501 .muxsel = MUXSEL(2, 3, 1, 1), 502 .gpiomux = { 0x20001,0x10001, 0, 0 }, 503 .gpiomute = 10, 504 .tuner_type = UNSET, 505 .tuner_addr = ADDR_UNSET, 506 }, 507 508 /* ---- card 0x0c ---------------------------------- */ 509 [BTTV_BOARD_ADSTECH_TV] = { 510 .name = "ADS Technologies Channel Surfer TV (bt848)", 511 .video_inputs = 3, 512 /* .audio_inputs= 1, */ 513 .svhs = 2, 514 .gpiomask = 15, 515 .muxsel = MUXSEL(2, 3, 1, 1), 516 .gpiomux = { 13, 14, 11, 7 }, 517 .tuner_type = UNSET, 518 .tuner_addr = ADDR_UNSET, 519 }, 520 [BTTV_BOARD_AVERMEDIA98] = { 521 .name = "AVerMedia TVCapture 98", 522 .video_inputs = 3, 523 /* .audio_inputs= 4, */ 524 .svhs = 2, 525 .gpiomask = 15, 526 .muxsel = MUXSEL(2, 3, 1, 1), 527 .gpiomux = { 13, 14, 11, 7 }, 528 .msp34xx_alt = 1, 529 .pll = PLL_28, 530 .tuner_type = TUNER_PHILIPS_PAL, 531 .tuner_addr = ADDR_UNSET, 532 .audio_mode_gpio= avermedia_tv_stereo_audio, 533 .no_gpioirq = 1, 534 }, 535 [BTTV_BOARD_VHX] = { 536 .name = "Aimslab Video Highway Xtreme (VHX)", 537 .video_inputs = 3, 538 /* .audio_inputs= 1, */ 539 .svhs = 2, 540 .gpiomask = 7, 541 .muxsel = MUXSEL(2, 3, 1, 1), 542 .gpiomux = { 0, 2, 1, 3 }, /* old: {0, 1, 2, 3, 4} */ 543 .gpiomute = 4, 544 .pll = PLL_28, 545 .tuner_type = UNSET, 546 .tuner_addr = ADDR_UNSET, 547 }, 548 [BTTV_BOARD_ZOLTRIX] = { 549 .name = "Zoltrix TV-Max", 550 .video_inputs = 3, 551 /* .audio_inputs= 1, */ 552 .svhs = 2, 553 .gpiomask = 15, 554 .muxsel = MUXSEL(2, 3, 1, 1), 555 .gpiomux = { 0, 0, 1, 0 }, 556 .gpiomute = 10, 557 .tuner_type = UNSET, 558 .tuner_addr = ADDR_UNSET, 559 }, 560 561 /* ---- card 0x10 ---------------------------------- */ 562 [BTTV_BOARD_PIXVIEWPLAYTV] = { 563 .name = "Prolink Pixelview PlayTV (bt878)", 564 .video_inputs = 3, 565 /* .audio_inputs= 1, */ 566 .svhs = 2, 567 .gpiomask = 0x01fe00, 568 .muxsel = MUXSEL(2, 3, 1, 1), 569 /* 2003-10-20 by "Anton A. Arapov" <arapov@mail.ru> */ 570 .gpiomux = { 0x001e00, 0, 0x018000, 0x014000 }, 571 .gpiomute = 0x002000, 572 .pll = PLL_28, 573 .tuner_type = UNSET, 574 .tuner_addr = ADDR_UNSET, 575 }, 576 [BTTV_BOARD_WINVIEW_601] = { 577 .name = "Leadtek WinView 601", 578 .video_inputs = 3, 579 /* .audio_inputs= 1, */ 580 .svhs = 2, 581 .gpiomask = 0x8300f8, 582 .muxsel = MUXSEL(2, 3, 1, 1, 0), 583 .gpiomux = { 0x4fa007,0xcfa007,0xcfa007,0xcfa007 }, 584 .gpiomute = 0xcfa007, 585 .tuner_type = UNSET, 586 .tuner_addr = ADDR_UNSET, 587 .volume_gpio = winview_volume, 588 .has_radio = 1, 589 }, 590 [BTTV_BOARD_AVEC_INTERCAP] = { 591 .name = "AVEC Intercapture", 592 .video_inputs = 3, 593 /* .audio_inputs= 2, */ 594 .svhs = 2, 595 .gpiomask = 0, 596 .muxsel = MUXSEL(2, 3, 1, 1), 597 .gpiomux = { 1, 0, 0, 0 }, 598 .tuner_type = UNSET, 599 .tuner_addr = ADDR_UNSET, 600 }, 601 [BTTV_BOARD_LIFE_FLYKIT] = { 602 .name = "Lifeview FlyVideo II EZ /FlyKit LR38 Bt848 (capture only)", 603 .video_inputs = 4, 604 /* .audio_inputs= 1, */ 605 .svhs = NO_SVHS, 606 .gpiomask = 0x8dff00, 607 .muxsel = MUXSEL(2, 3, 1, 1), 608 .gpiomux = { 0 }, 609 .no_msp34xx = 1, 610 .tuner_type = TUNER_ABSENT, 611 .tuner_addr = ADDR_UNSET, 612 }, 613 614 /* ---- card 0x14 ---------------------------------- */ 615 [BTTV_BOARD_CEI_RAFFLES] = { 616 .name = "CEI Raffles Card", 617 .video_inputs = 3, 618 /* .audio_inputs= 3, */ 619 .svhs = 2, 620 .muxsel = MUXSEL(2, 3, 1, 1), 621 .tuner_type = UNSET, 622 .tuner_addr = ADDR_UNSET, 623 }, 624 [BTTV_BOARD_CONFERENCETV] = { 625 .name = "Lifeview FlyVideo 98/ Lucky Star Image World ConferenceTV LR50", 626 .video_inputs = 4, 627 /* .audio_inputs= 2, tuner, line in */ 628 .svhs = 2, 629 .gpiomask = 0x1800, 630 .muxsel = MUXSEL(2, 3, 1, 1), 631 .gpiomux = { 0, 0x800, 0x1000, 0x1000 }, 632 .gpiomute = 0x1800, 633 .pll = PLL_28, 634 .tuner_type = TUNER_PHILIPS_PAL_I, 635 .tuner_addr = ADDR_UNSET, 636 }, 637 [BTTV_BOARD_PHOEBE_TVMAS] = { 638 .name = "Askey CPH050/ Phoebe Tv Master + FM", 639 .video_inputs = 3, 640 /* .audio_inputs= 1, */ 641 .svhs = 2, 642 .gpiomask = 0xc00, 643 .muxsel = MUXSEL(2, 3, 1, 1), 644 .gpiomux = { 0, 1, 0x800, 0x400 }, 645 .gpiomute = 0xc00, 646 .pll = PLL_28, 647 .tuner_type = UNSET, 648 .tuner_addr = ADDR_UNSET, 649 }, 650 [BTTV_BOARD_MODTEC_205] = { 651 .name = "Modular Technology MM201/MM202/MM205/MM210/MM215 PCTV, bt878", 652 .video_inputs = 3, 653 /* .audio_inputs= 1, */ 654 .svhs = NO_SVHS, 655 .has_dig_in = 1, 656 .gpiomask = 7, 657 .muxsel = MUXSEL(2, 3, 0), /* input 2 is digital */ 658 /* .digital_mode= DIGITAL_MODE_CAMERA, */ 659 .gpiomux = { 0, 0, 0, 0 }, 660 .no_msp34xx = 1, 661 .pll = PLL_28, 662 .tuner_type = TUNER_ALPS_TSBB5_PAL_I, 663 .tuner_addr = ADDR_UNSET, 664 }, 665 666 /* ---- card 0x18 ---------------------------------- */ 667 [BTTV_BOARD_MAGICTVIEW061] = { 668 .name = "Askey CPH05X/06X (bt878) [many vendors]", 669 .video_inputs = 3, 670 /* .audio_inputs= 1, */ 671 .svhs = 2, 672 .gpiomask = 0xe00, 673 .muxsel = MUXSEL(2, 3, 1, 1), 674 .gpiomux = {0x400, 0x400, 0x400, 0x400 }, 675 .gpiomute = 0xc00, 676 .pll = PLL_28, 677 .tuner_type = UNSET, 678 .tuner_addr = ADDR_UNSET, 679 .has_remote = 1, 680 .has_radio = 1, /* not every card has radio */ 681 }, 682 [BTTV_BOARD_VOBIS_BOOSTAR] = { 683 .name = "Terratec TerraTV+ Version 1.0 (Bt848)/ Terra TValue Version 1.0/ Vobis TV-Boostar", 684 .video_inputs = 3, 685 /* .audio_inputs= 1, */ 686 .svhs = 2, 687 .gpiomask = 0x1f0fff, 688 .muxsel = MUXSEL(2, 3, 1, 1), 689 .gpiomux = { 0x20000, 0x30000, 0x10000, 0 }, 690 .gpiomute = 0x40000, 691 .tuner_type = TUNER_PHILIPS_PAL, 692 .tuner_addr = ADDR_UNSET, 693 .audio_mode_gpio= terratv_audio, 694 }, 695 [BTTV_BOARD_HAUPPAUG_WCAM] = { 696 .name = "Hauppauge WinCam newer (bt878)", 697 .video_inputs = 4, 698 /* .audio_inputs= 1, */ 699 .svhs = 3, 700 .gpiomask = 7, 701 .muxsel = MUXSEL(2, 0, 1, 1), 702 .gpiomux = { 0, 1, 2, 3 }, 703 .gpiomute = 4, 704 .tuner_type = UNSET, 705 .tuner_addr = ADDR_UNSET, 706 }, 707 [BTTV_BOARD_MAXI] = { 708 .name = "Lifeview FlyVideo 98/ MAXI TV Video PCI2 LR50", 709 .video_inputs = 4, 710 /* .audio_inputs= 2, */ 711 .svhs = 2, 712 .gpiomask = 0x1800, 713 .muxsel = MUXSEL(2, 3, 1, 1), 714 .gpiomux = { 0, 0x800, 0x1000, 0x1000 }, 715 .gpiomute = 0x1800, 716 .pll = PLL_28, 717 .tuner_type = TUNER_PHILIPS_SECAM, 718 .tuner_addr = ADDR_UNSET, 719 }, 720 721 /* ---- card 0x1c ---------------------------------- */ 722 [BTTV_BOARD_TERRATV] = { 723 .name = "Terratec TerraTV+ Version 1.1 (bt878)", 724 .video_inputs = 3, 725 /* .audio_inputs= 1, */ 726 .svhs = 2, 727 .gpiomask = 0x1f0fff, 728 .muxsel = MUXSEL(2, 3, 1, 1), 729 .gpiomux = { 0x20000, 0x30000, 0x10000, 0x00000 }, 730 .gpiomute = 0x40000, 731 .tuner_type = TUNER_PHILIPS_PAL, 732 .tuner_addr = ADDR_UNSET, 733 .audio_mode_gpio= terratv_audio, 734 /* GPIO wiring: 735 External 20 pin connector (for Active Radio Upgrade board) 736 gpio00: i2c-sda 737 gpio01: i2c-scl 738 gpio02: om5610-data 739 gpio03: om5610-clk 740 gpio04: om5610-wre 741 gpio05: om5610-stereo 742 gpio06: rds6588-davn 743 gpio07: Pin 7 n.c. 744 gpio08: nIOW 745 gpio09+10: nIOR, nSEL ?? (bt878) 746 gpio09: nIOR (bt848) 747 gpio10: nSEL (bt848) 748 Sound Routing: 749 gpio16: u2-A0 (1st 4052bt) 750 gpio17: u2-A1 751 gpio18: u2-nEN 752 gpio19: u4-A0 (2nd 4052) 753 gpio20: u4-A1 754 u4-nEN - GND 755 Btspy: 756 00000 : Cdrom (internal audio input) 757 10000 : ext. Video audio input 758 20000 : TV Mono 759 a0000 : TV Mono/2 760 1a0000 : TV Stereo 761 30000 : Radio 762 40000 : Mute 763 */ 764 765 }, 766 [BTTV_BOARD_PXC200] = { 767 /* Jannik Fritsch <jannik@techfak.uni-bielefeld.de> */ 768 .name = "Imagenation PXC200", 769 .video_inputs = 5, 770 /* .audio_inputs= 1, */ 771 .svhs = 1, /* was: 4 */ 772 .gpiomask = 0, 773 .muxsel = MUXSEL(2, 3, 1, 0, 0), 774 .gpiomux = { 0 }, 775 .tuner_type = TUNER_ABSENT, 776 .tuner_addr = ADDR_UNSET, 777 .muxsel_hook = PXC200_muxsel, 778 779 }, 780 [BTTV_BOARD_FLYVIDEO_98] = { 781 .name = "Lifeview FlyVideo 98 LR50", 782 .video_inputs = 4, 783 /* .audio_inputs= 1, */ 784 .svhs = 2, 785 .gpiomask = 0x1800, /* 0x8dfe00 */ 786 .muxsel = MUXSEL(2, 3, 1, 1), 787 .gpiomux = { 0, 0x0800, 0x1000, 0x1000 }, 788 .gpiomute = 0x1800, 789 .pll = PLL_28, 790 .tuner_type = UNSET, 791 .tuner_addr = ADDR_UNSET, 792 }, 793 [BTTV_BOARD_IPROTV] = { 794 .name = "Formac iProTV, Formac ProTV I (bt848)", 795 .video_inputs = 4, 796 /* .audio_inputs= 1, */ 797 .svhs = 3, 798 .gpiomask = 1, 799 .muxsel = MUXSEL(2, 3, 1, 1), 800 .gpiomux = { 1, 0, 0, 0 }, 801 .pll = PLL_28, 802 .tuner_type = TUNER_PHILIPS_PAL, 803 .tuner_addr = ADDR_UNSET, 804 }, 805 806 /* ---- card 0x20 ---------------------------------- */ 807 [BTTV_BOARD_INTEL_C_S_PCI] = { 808 .name = "Intel Create and Share PCI/ Smart Video Recorder III", 809 .video_inputs = 4, 810 /* .audio_inputs= 0, */ 811 .svhs = 2, 812 .gpiomask = 0, 813 .muxsel = MUXSEL(2, 3, 1, 1), 814 .gpiomux = { 0 }, 815 .tuner_type = TUNER_ABSENT, 816 .tuner_addr = ADDR_UNSET, 817 }, 818 [BTTV_BOARD_TERRATVALUE] = { 819 .name = "Terratec TerraTValue Version Bt878", 820 .video_inputs = 3, 821 /* .audio_inputs= 1, */ 822 .svhs = 2, 823 .gpiomask = 0xffff00, 824 .muxsel = MUXSEL(2, 3, 1, 1), 825 .gpiomux = { 0x500, 0, 0x300, 0x900 }, 826 .gpiomute = 0x900, 827 .pll = PLL_28, 828 .tuner_type = TUNER_PHILIPS_PAL, 829 .tuner_addr = ADDR_UNSET, 830 }, 831 [BTTV_BOARD_WINFAST2000] = { 832 .name = "Leadtek WinFast 2000/ WinFast 2000 XP", 833 .video_inputs = 4, 834 /* .audio_inputs= 1, */ 835 .svhs = 2, 836 /* TV, CVid, SVid, CVid over SVid connector */ 837 .muxsel = MUXSEL(2, 3, 1, 1, 0), 838 /* Alexander Varakin <avarakin@hotmail.com> [stereo version] */ 839 .gpiomask = 0xb33000, 840 .gpiomux = { 0x122000,0x1000,0x0000,0x620000 }, 841 .gpiomute = 0x800000, 842 /* Audio Routing for "WinFast 2000 XP" (no tv stereo !) 843 gpio23 -- hef4052:nEnable (0x800000) 844 gpio12 -- hef4052:A1 845 gpio13 -- hef4052:A0 846 0x0000: external audio 847 0x1000: FM 848 0x2000: TV 849 0x3000: n.c. 850 Note: There exists another variant "Winfast 2000" with tv stereo !? 851 Note: eeprom only contains FF and pci subsystem id 107d:6606 852 */ 853 .pll = PLL_28, 854 .has_radio = 1, 855 .tuner_type = TUNER_PHILIPS_PAL, /* default for now, gpio reads BFFF06 for Pal bg+dk */ 856 .tuner_addr = ADDR_UNSET, 857 .audio_mode_gpio= winfast2000_audio, 858 .has_remote = 1, 859 }, 860 [BTTV_BOARD_CHRONOS_VS2] = { 861 .name = "Lifeview FlyVideo 98 LR50 / Chronos Video Shuttle II", 862 .video_inputs = 4, 863 /* .audio_inputs= 3, */ 864 .svhs = 2, 865 .gpiomask = 0x1800, 866 .muxsel = MUXSEL(2, 3, 1, 1), 867 .gpiomux = { 0, 0x800, 0x1000, 0x1000 }, 868 .gpiomute = 0x1800, 869 .pll = PLL_28, 870 .tuner_type = UNSET, 871 .tuner_addr = ADDR_UNSET, 872 }, 873 874 /* ---- card 0x24 ---------------------------------- */ 875 [BTTV_BOARD_TYPHOON_TVIEW] = { 876 .name = "Lifeview FlyVideo 98FM LR50 / Typhoon TView TV/FM Tuner", 877 .video_inputs = 4, 878 /* .audio_inputs= 3, */ 879 .svhs = 2, 880 .gpiomask = 0x1800, 881 .muxsel = MUXSEL(2, 3, 1, 1), 882 .gpiomux = { 0, 0x800, 0x1000, 0x1000 }, 883 .gpiomute = 0x1800, 884 .pll = PLL_28, 885 .tuner_type = UNSET, 886 .tuner_addr = ADDR_UNSET, 887 .has_radio = 1, 888 }, 889 [BTTV_BOARD_PXELVWPLTVPRO] = { 890 .name = "Prolink PixelView PlayTV pro", 891 .video_inputs = 3, 892 /* .audio_inputs= 1, */ 893 .svhs = 2, 894 .gpiomask = 0xff, 895 .muxsel = MUXSEL(2, 3, 1, 1), 896 .gpiomux = { 0x21, 0x20, 0x24, 0x2c }, 897 .gpiomute = 0x29, 898 .no_msp34xx = 1, 899 .pll = PLL_28, 900 .tuner_type = UNSET, 901 .tuner_addr = ADDR_UNSET, 902 }, 903 [BTTV_BOARD_MAGICTVIEW063] = { 904 .name = "Askey CPH06X TView99", 905 .video_inputs = 4, 906 /* .audio_inputs= 1, */ 907 .svhs = 2, 908 .gpiomask = 0x551e00, 909 .muxsel = MUXSEL(2, 3, 1, 0), 910 .gpiomux = { 0x551400, 0x551200, 0, 0 }, 911 .gpiomute = 0x551c00, 912 .pll = PLL_28, 913 .tuner_type = TUNER_PHILIPS_PAL_I, 914 .tuner_addr = ADDR_UNSET, 915 .has_remote = 1, 916 }, 917 [BTTV_BOARD_PINNACLE] = { 918 .name = "Pinnacle PCTV Studio/Rave", 919 .video_inputs = 3, 920 /* .audio_inputs= 1, */ 921 .svhs = 2, 922 .gpiomask = 0x03000F, 923 .muxsel = MUXSEL(2, 3, 1, 1), 924 .gpiomux = { 2, 0xd0001, 0, 0 }, 925 .gpiomute = 1, 926 .pll = PLL_28, 927 .tuner_type = UNSET, 928 .tuner_addr = ADDR_UNSET, 929 }, 930 931 /* ---- card 0x28 ---------------------------------- */ 932 [BTTV_BOARD_STB2] = { 933 .name = "STB TV PCI FM, Gateway P/N 6000704 (bt878), 3Dfx VoodooTV 100", 934 .video_inputs = 3, 935 /* .audio_inputs= 1, */ 936 .svhs = 2, 937 .gpiomask = 7, 938 .muxsel = MUXSEL(2, 3, 1, 1), 939 .gpiomux = { 4, 0, 2, 3 }, 940 .gpiomute = 1, 941 .no_msp34xx = 1, 942 .tuner_type = TUNER_PHILIPS_NTSC, 943 .tuner_addr = ADDR_UNSET, 944 .pll = PLL_28, 945 .has_radio = 1, 946 }, 947 [BTTV_BOARD_AVPHONE98] = { 948 .name = "AVerMedia TVPhone 98", 949 .video_inputs = 3, 950 /* .audio_inputs= 4, */ 951 .svhs = 2, 952 .gpiomask = 15, 953 .muxsel = MUXSEL(2, 3, 1, 1), 954 .gpiomux = { 13, 4, 11, 7 }, 955 .pll = PLL_28, 956 .tuner_type = UNSET, 957 .tuner_addr = ADDR_UNSET, 958 .has_radio = 1, 959 .audio_mode_gpio= avermedia_tvphone_audio, 960 }, 961 [BTTV_BOARD_PV951] = { 962 .name = "ProVideo PV951", /* pic16c54 */ 963 .video_inputs = 3, 964 /* .audio_inputs= 1, */ 965 .svhs = 2, 966 .gpiomask = 0, 967 .muxsel = MUXSEL(2, 3, 1, 1), 968 .gpiomux = { 0, 0, 0, 0}, 969 .no_msp34xx = 1, 970 .pll = PLL_28, 971 .tuner_type = TUNER_PHILIPS_PAL_I, 972 .tuner_addr = ADDR_UNSET, 973 }, 974 [BTTV_BOARD_ONAIR_TV] = { 975 .name = "Little OnAir TV", 976 .video_inputs = 3, 977 /* .audio_inputs= 1, */ 978 .svhs = 2, 979 .gpiomask = 0xe00b, 980 .muxsel = MUXSEL(2, 3, 1, 1), 981 .gpiomux = { 0xff9ff6, 0xff9ff6, 0xff1ff7, 0 }, 982 .gpiomute = 0xff3ffc, 983 .no_msp34xx = 1, 984 .tuner_type = UNSET, 985 .tuner_addr = ADDR_UNSET, 986 }, 987 988 /* ---- card 0x2c ---------------------------------- */ 989 [BTTV_BOARD_SIGMA_TVII_FM] = { 990 .name = "Sigma TVII-FM", 991 .video_inputs = 2, 992 /* .audio_inputs= 1, */ 993 .svhs = NO_SVHS, 994 .gpiomask = 3, 995 .muxsel = MUXSEL(2, 3, 1, 1), 996 .gpiomux = { 1, 1, 0, 2 }, 997 .gpiomute = 3, 998 .no_msp34xx = 1, 999 .pll = PLL_NONE, 1000 .tuner_type = UNSET, 1001 .tuner_addr = ADDR_UNSET, 1002 }, 1003 [BTTV_BOARD_MATRIX_VISION2] = { 1004 .name = "MATRIX-Vision MV-Delta 2", 1005 .video_inputs = 5, 1006 /* .audio_inputs= 1, */ 1007 .svhs = 3, 1008 .gpiomask = 0, 1009 .muxsel = MUXSEL(2, 3, 1, 0, 0), 1010 .gpiomux = { 0 }, 1011 .no_msp34xx = 1, 1012 .pll = PLL_28, 1013 .tuner_type = TUNER_ABSENT, 1014 .tuner_addr = ADDR_UNSET, 1015 }, 1016 [BTTV_BOARD_ZOLTRIX_GENIE] = { 1017 .name = "Zoltrix Genie TV/FM", 1018 .video_inputs = 3, 1019 /* .audio_inputs= 1, */ 1020 .svhs = 2, 1021 .gpiomask = 0xbcf03f, 1022 .muxsel = MUXSEL(2, 3, 1, 1), 1023 .gpiomux = { 0xbc803f, 0xbc903f, 0xbcb03f, 0 }, 1024 .gpiomute = 0xbcb03f, 1025 .no_msp34xx = 1, 1026 .pll = PLL_28, 1027 .tuner_type = TUNER_TEMIC_4039FR5_NTSC, 1028 .tuner_addr = ADDR_UNSET, 1029 }, 1030 [BTTV_BOARD_TERRATVRADIO] = { 1031 .name = "Terratec TV/Radio+", 1032 .video_inputs = 3, 1033 /* .audio_inputs= 1, */ 1034 .svhs = 2, 1035 .gpiomask = 0x70000, 1036 .muxsel = MUXSEL(2, 3, 1, 1), 1037 .gpiomux = { 0x20000, 0x30000, 0x10000, 0 }, 1038 .gpiomute = 0x40000, 1039 .no_msp34xx = 1, 1040 .pll = PLL_35, 1041 .tuner_type = TUNER_PHILIPS_PAL_I, 1042 .tuner_addr = ADDR_UNSET, 1043 .has_radio = 1, 1044 }, 1045 1046 /* ---- card 0x30 ---------------------------------- */ 1047 [BTTV_BOARD_DYNALINK] = { 1048 .name = "Askey CPH03x/ Dynalink Magic TView", 1049 .video_inputs = 3, 1050 /* .audio_inputs= 1, */ 1051 .svhs = 2, 1052 .gpiomask = 15, 1053 .muxsel = MUXSEL(2, 3, 1, 1), 1054 .gpiomux = {2,0,0,0 }, 1055 .gpiomute = 1, 1056 .pll = PLL_28, 1057 .tuner_type = UNSET, 1058 .tuner_addr = ADDR_UNSET, 1059 }, 1060 [BTTV_BOARD_GVBCTV3PCI] = { 1061 .name = "IODATA GV-BCTV3/PCI", 1062 .video_inputs = 3, 1063 /* .audio_inputs= 1, */ 1064 .svhs = 2, 1065 .gpiomask = 0x010f00, 1066 .muxsel = MUXSEL(2, 3, 0, 0), 1067 .gpiomux = {0x10000, 0, 0x10000, 0 }, 1068 .no_msp34xx = 1, 1069 .pll = PLL_28, 1070 .tuner_type = TUNER_ALPS_TSHC6_NTSC, 1071 .tuner_addr = ADDR_UNSET, 1072 .audio_mode_gpio= gvbctv3pci_audio, 1073 }, 1074 [BTTV_BOARD_PXELVWPLTVPAK] = { 1075 .name = "Prolink PV-BT878P+4E / PixelView PlayTV PAK / Lenco MXTV-9578 CP", 1076 .video_inputs = 5, 1077 /* .audio_inputs= 1, */ 1078 .svhs = 3, 1079 .has_dig_in = 1, 1080 .gpiomask = 0xAA0000, 1081 .muxsel = MUXSEL(2, 3, 1, 1, 0), /* in 4 is digital */ 1082 /* .digital_mode= DIGITAL_MODE_CAMERA, */ 1083 .gpiomux = { 0x20000, 0, 0x80000, 0x80000 }, 1084 .gpiomute = 0xa8000, 1085 .no_msp34xx = 1, 1086 .pll = PLL_28, 1087 .tuner_type = TUNER_PHILIPS_PAL_I, 1088 .tuner_addr = ADDR_UNSET, 1089 .has_remote = 1, 1090 /* GPIO wiring: (different from Rev.4C !) 1091 GPIO17: U4.A0 (first hef4052bt) 1092 GPIO19: U4.A1 1093 GPIO20: U5.A1 (second hef4052bt) 1094 GPIO21: U4.nEN 1095 GPIO22: BT832 Reset Line 1096 GPIO23: A5,A0, U5,nEN 1097 Note: At i2c=0x8a is a Bt832 chip, which changes to 0x88 after being reset via GPIO22 1098 */ 1099 }, 1100 [BTTV_BOARD_EAGLE] = { 1101 .name = "Eagle Wireless Capricorn2 (bt878A)", 1102 .video_inputs = 4, 1103 /* .audio_inputs= 1, */ 1104 .svhs = 2, 1105 .gpiomask = 7, 1106 .muxsel = MUXSEL(2, 0, 1, 1), 1107 .gpiomux = { 0, 1, 2, 3 }, 1108 .gpiomute = 4, 1109 .pll = PLL_28, 1110 .tuner_type = UNSET /* TUNER_ALPS_TMDH2_NTSC */, 1111 .tuner_addr = ADDR_UNSET, 1112 }, 1113 1114 /* ---- card 0x34 ---------------------------------- */ 1115 [BTTV_BOARD_PINNACLEPRO] = { 1116 /* David Härdeman <david@2gen.com> */ 1117 .name = "Pinnacle PCTV Studio Pro", 1118 .video_inputs = 4, 1119 /* .audio_inputs= 1, */ 1120 .svhs = 3, 1121 .gpiomask = 0x03000F, 1122 .muxsel = MUXSEL(2, 3, 1, 1), 1123 .gpiomux = { 1, 0xd0001, 0, 0 }, 1124 .gpiomute = 10, 1125 /* sound path (5 sources): 1126 MUX1 (mask 0x03), Enable Pin 0x08 (0=enable, 1=disable) 1127 0= ext. Audio IN 1128 1= from MUX2 1129 2= Mono TV sound from Tuner 1130 3= not connected 1131 MUX2 (mask 0x30000): 1132 0,2,3= from MSP34xx 1133 1= FM stereo Radio from Tuner */ 1134 .pll = PLL_28, 1135 .tuner_type = UNSET, 1136 .tuner_addr = ADDR_UNSET, 1137 }, 1138 [BTTV_BOARD_TVIEW_RDS_FM] = { 1139 /* Claas Langbehn <claas@bigfoot.com>, 1140 Sven Grothklags <sven@upb.de> */ 1141 .name = "Typhoon TView RDS + FM Stereo / KNC1 TV Station RDS", 1142 .video_inputs = 4, 1143 /* .audio_inputs= 3, */ 1144 .svhs = 2, 1145 .gpiomask = 0x1c, 1146 .muxsel = MUXSEL(2, 3, 1, 1), 1147 .gpiomux = { 0, 0, 0x10, 8 }, 1148 .gpiomute = 4, 1149 .pll = PLL_28, 1150 .tuner_type = TUNER_PHILIPS_PAL, 1151 .tuner_addr = ADDR_UNSET, 1152 .has_radio = 1, 1153 }, 1154 [BTTV_BOARD_LIFETEC_9415] = { 1155 /* Tim Röstermundt <rosterm@uni-muenster.de> 1156 in de.comp.os.unix.linux.hardware: 1157 options bttv card=0 pll=1 radio=1 gpiomask=0x18e0 1158 gpiomux =0x44c71f,0x44d71f,0,0x44d71f,0x44dfff 1159 options tuner type=5 */ 1160 .name = "Lifeview FlyVideo 2000 /FlyVideo A2/ Lifetec LT 9415 TV [LR90]", 1161 .video_inputs = 4, 1162 /* .audio_inputs= 1, */ 1163 .svhs = 2, 1164 .gpiomask = 0x18e0, 1165 .muxsel = MUXSEL(2, 3, 1, 1), 1166 .gpiomux = { 0x0000,0x0800,0x1000,0x1000 }, 1167 .gpiomute = 0x18e0, 1168 /* For cards with tda9820/tda9821: 1169 0x0000: Tuner normal stereo 1170 0x0080: Tuner A2 SAP (second audio program = Zweikanalton) 1171 0x0880: Tuner A2 stereo */ 1172 .pll = PLL_28, 1173 .tuner_type = UNSET, 1174 .tuner_addr = ADDR_UNSET, 1175 }, 1176 [BTTV_BOARD_BESTBUY_EASYTV] = { 1177 /* Miguel Angel Alvarez <maacruz@navegalia.com> 1178 old Easy TV BT848 version (model CPH031) */ 1179 .name = "Askey CPH031/ BESTBUY Easy TV", 1180 .video_inputs = 4, 1181 /* .audio_inputs= 1, */ 1182 .svhs = 2, 1183 .gpiomask = 0xF, 1184 .muxsel = MUXSEL(2, 3, 1, 0), 1185 .gpiomux = { 2, 0, 0, 0 }, 1186 .gpiomute = 10, 1187 .pll = PLL_28, 1188 .tuner_type = TUNER_TEMIC_PAL, 1189 .tuner_addr = ADDR_UNSET, 1190 }, 1191 1192 /* ---- card 0x38 ---------------------------------- */ 1193 [BTTV_BOARD_FLYVIDEO_98FM] = { 1194 /* Gordon Heydon <gjheydon@bigfoot.com ('98) */ 1195 .name = "Lifeview FlyVideo 98FM LR50", 1196 .video_inputs = 4, 1197 /* .audio_inputs= 3, */ 1198 .svhs = 2, 1199 .gpiomask = 0x1800, 1200 .muxsel = MUXSEL(2, 3, 1, 1), 1201 .gpiomux = { 0, 0x800, 0x1000, 0x1000 }, 1202 .gpiomute = 0x1800, 1203 .pll = PLL_28, 1204 .tuner_type = TUNER_PHILIPS_PAL, 1205 .tuner_addr = ADDR_UNSET, 1206 }, 1207 /* This is the ultimate cheapo capture card 1208 * just a BT848A on a small PCB! 1209 * Steve Hosgood <steve@equiinet.com> */ 1210 [BTTV_BOARD_GRANDTEC] = { 1211 .name = "GrandTec 'Grand Video Capture' (Bt848)", 1212 .video_inputs = 2, 1213 /* .audio_inputs= 0, */ 1214 .svhs = 1, 1215 .gpiomask = 0, 1216 .muxsel = MUXSEL(3, 1), 1217 .gpiomux = { 0 }, 1218 .no_msp34xx = 1, 1219 .pll = PLL_35, 1220 .tuner_type = TUNER_ABSENT, 1221 .tuner_addr = ADDR_UNSET, 1222 }, 1223 [BTTV_BOARD_ASKEY_CPH060] = { 1224 /* Daniel Herrington <daniel.herrington@home.com> */ 1225 .name = "Askey CPH060/ Phoebe TV Master Only (No FM)", 1226 .video_inputs = 3, 1227 /* .audio_inputs= 1, */ 1228 .svhs = 2, 1229 .gpiomask = 0xe00, 1230 .muxsel = MUXSEL(2, 3, 1, 1), 1231 .gpiomux = { 0x400, 0x400, 0x400, 0x400 }, 1232 .gpiomute = 0x800, 1233 .pll = PLL_28, 1234 .tuner_type = TUNER_TEMIC_4036FY5_NTSC, 1235 .tuner_addr = ADDR_UNSET, 1236 }, 1237 [BTTV_BOARD_ASKEY_CPH03X] = { 1238 /* Matti Mottus <mottus@physic.ut.ee> */ 1239 .name = "Askey CPH03x TV Capturer", 1240 .video_inputs = 4, 1241 /* .audio_inputs= 1, */ 1242 .svhs = 2, 1243 .gpiomask = 0x03000F, 1244 .muxsel = MUXSEL(2, 3, 1, 0), 1245 .gpiomux = { 2, 0, 0, 0 }, 1246 .gpiomute = 1, 1247 .pll = PLL_28, 1248 .tuner_type = TUNER_TEMIC_PAL, 1249 .tuner_addr = ADDR_UNSET, 1250 .has_remote = 1, 1251 }, 1252 1253 /* ---- card 0x3c ---------------------------------- */ 1254 [BTTV_BOARD_MM100PCTV] = { 1255 /* Philip Blundell <philb@gnu.org> */ 1256 .name = "Modular Technology MM100PCTV", 1257 .video_inputs = 2, 1258 /* .audio_inputs= 2, */ 1259 .svhs = NO_SVHS, 1260 .gpiomask = 11, 1261 .muxsel = MUXSEL(2, 3, 1, 1), 1262 .gpiomux = { 2, 0, 0, 1 }, 1263 .gpiomute = 8, 1264 .pll = PLL_35, 1265 .tuner_type = TUNER_TEMIC_PAL, 1266 .tuner_addr = ADDR_UNSET, 1267 }, 1268 [BTTV_BOARD_GMV1] = { 1269 /* Adrian Cox <adrian@humboldt.co.uk */ 1270 .name = "AG Electronics GMV1", 1271 .video_inputs = 2, 1272 /* .audio_inputs= 0, */ 1273 .svhs = 1, 1274 .gpiomask = 0xF, 1275 .muxsel = MUXSEL(2, 2), 1276 .gpiomux = { }, 1277 .no_msp34xx = 1, 1278 .pll = PLL_28, 1279 .tuner_type = TUNER_ABSENT, 1280 .tuner_addr = ADDR_UNSET, 1281 }, 1282 [BTTV_BOARD_BESTBUY_EASYTV2] = { 1283 /* Miguel Angel Alvarez <maacruz@navegalia.com> 1284 new Easy TV BT878 version (model CPH061) 1285 special thanks to Informatica Mieres for providing the card */ 1286 .name = "Askey CPH061/ BESTBUY Easy TV (bt878)", 1287 .video_inputs = 3, 1288 /* .audio_inputs= 2, */ 1289 .svhs = 2, 1290 .gpiomask = 0xFF, 1291 .muxsel = MUXSEL(2, 3, 1, 0), 1292 .gpiomux = { 1, 0, 4, 4 }, 1293 .gpiomute = 9, 1294 .pll = PLL_28, 1295 .tuner_type = TUNER_PHILIPS_PAL, 1296 .tuner_addr = ADDR_UNSET, 1297 }, 1298 [BTTV_BOARD_ATI_TVWONDER] = { 1299 /* Lukas Gebauer <geby@volny.cz> */ 1300 .name = "ATI TV-Wonder", 1301 .video_inputs = 3, 1302 /* .audio_inputs= 1, */ 1303 .svhs = 2, 1304 .gpiomask = 0xf03f, 1305 .muxsel = MUXSEL(2, 3, 1, 0), 1306 .gpiomux = { 0xbffe, 0, 0xbfff, 0 }, 1307 .gpiomute = 0xbffe, 1308 .pll = PLL_28, 1309 .tuner_type = TUNER_TEMIC_4006FN5_MULTI_PAL, 1310 .tuner_addr = ADDR_UNSET, 1311 }, 1312 1313 /* ---- card 0x40 ---------------------------------- */ 1314 [BTTV_BOARD_ATI_TVWONDERVE] = { 1315 /* Lukas Gebauer <geby@volny.cz> */ 1316 .name = "ATI TV-Wonder VE", 1317 .video_inputs = 2, 1318 /* .audio_inputs= 1, */ 1319 .svhs = NO_SVHS, 1320 .gpiomask = 1, 1321 .muxsel = MUXSEL(2, 3, 0, 1), 1322 .gpiomux = { 0, 0, 1, 0 }, 1323 .no_msp34xx = 1, 1324 .pll = PLL_28, 1325 .tuner_type = TUNER_TEMIC_4006FN5_MULTI_PAL, 1326 .tuner_addr = ADDR_UNSET, 1327 }, 1328 [BTTV_BOARD_FLYVIDEO2000] = { 1329 /* DeeJay <deejay@westel900.net (2000S) */ 1330 .name = "Lifeview FlyVideo 2000S LR90", 1331 .video_inputs = 3, 1332 /* .audio_inputs= 3, */ 1333 .svhs = 2, 1334 .gpiomask = 0x18e0, 1335 .muxsel = MUXSEL(2, 3, 0, 1), 1336 /* Radio changed from 1e80 to 0x800 to make 1337 FlyVideo2000S in .hu happy (gm)*/ 1338 /* -dk-???: set mute=0x1800 for tda9874h daughterboard */ 1339 .gpiomux = { 0x0000,0x0800,0x1000,0x1000 }, 1340 .gpiomute = 0x1800, 1341 .audio_mode_gpio= fv2000s_audio, 1342 .no_msp34xx = 1, 1343 .pll = PLL_28, 1344 .tuner_type = TUNER_PHILIPS_PAL, 1345 .tuner_addr = ADDR_UNSET, 1346 }, 1347 [BTTV_BOARD_TERRATVALUER] = { 1348 .name = "Terratec TValueRadio", 1349 .video_inputs = 3, 1350 /* .audio_inputs= 1, */ 1351 .svhs = 2, 1352 .gpiomask = 0xffff00, 1353 .muxsel = MUXSEL(2, 3, 1, 1), 1354 .gpiomux = { 0x500, 0x500, 0x300, 0x900 }, 1355 .gpiomute = 0x900, 1356 .pll = PLL_28, 1357 .tuner_type = TUNER_PHILIPS_PAL, 1358 .tuner_addr = ADDR_UNSET, 1359 .has_radio = 1, 1360 }, 1361 [BTTV_BOARD_GVBCTV4PCI] = { 1362 /* TANAKA Kei <peg00625@nifty.com> */ 1363 .name = "IODATA GV-BCTV4/PCI", 1364 .video_inputs = 3, 1365 /* .audio_inputs= 1, */ 1366 .svhs = 2, 1367 .gpiomask = 0x010f00, 1368 .muxsel = MUXSEL(2, 3, 0, 0), 1369 .gpiomux = {0x10000, 0, 0x10000, 0 }, 1370 .no_msp34xx = 1, 1371 .pll = PLL_28, 1372 .tuner_type = TUNER_SHARP_2U5JF5540_NTSC, 1373 .tuner_addr = ADDR_UNSET, 1374 .audio_mode_gpio= gvbctv3pci_audio, 1375 }, 1376 1377 /* ---- card 0x44 ---------------------------------- */ 1378 [BTTV_BOARD_VOODOOTV_FM] = { 1379 .name = "3Dfx VoodooTV FM (Euro)", 1380 /* try "insmod msp3400 simple=0" if you have 1381 * sound problems with this card. */ 1382 .video_inputs = 4, 1383 /* .audio_inputs= 1, */ 1384 .svhs = NO_SVHS, 1385 .gpiomask = 0x4f8a00, 1386 /* 0x100000: 1=MSP enabled (0=disable again) 1387 * 0x010000: Connected to "S0" on tda9880 (0=Pal/BG, 1=NTSC) */ 1388 .gpiomux = {0x947fff, 0x987fff,0x947fff,0x947fff }, 1389 .gpiomute = 0x947fff, 1390 /* tvtuner, radio, external,internal, mute, stereo 1391 * tuner, Composit, SVid, Composit-on-Svid-adapter */ 1392 .muxsel = MUXSEL(2, 3, 0, 1), 1393 .tuner_type = TUNER_MT2032, 1394 .tuner_addr = ADDR_UNSET, 1395 .pll = PLL_28, 1396 .has_radio = 1, 1397 }, 1398 [BTTV_BOARD_VOODOOTV_200] = { 1399 .name = "VoodooTV 200 (USA)", 1400 /* try "insmod msp3400 simple=0" if you have 1401 * sound problems with this card. */ 1402 .video_inputs = 4, 1403 /* .audio_inputs= 1, */ 1404 .svhs = NO_SVHS, 1405 .gpiomask = 0x4f8a00, 1406 /* 0x100000: 1=MSP enabled (0=disable again) 1407 * 0x010000: Connected to "S0" on tda9880 (0=Pal/BG, 1=NTSC) */ 1408 .gpiomux = {0x947fff, 0x987fff,0x947fff,0x947fff }, 1409 .gpiomute = 0x947fff, 1410 /* tvtuner, radio, external,internal, mute, stereo 1411 * tuner, Composit, SVid, Composit-on-Svid-adapter */ 1412 .muxsel = MUXSEL(2, 3, 0, 1), 1413 .tuner_type = TUNER_MT2032, 1414 .tuner_addr = ADDR_UNSET, 1415 .pll = PLL_28, 1416 .has_radio = 1, 1417 }, 1418 [BTTV_BOARD_AIMMS] = { 1419 /* Philip Blundell <pb@nexus.co.uk> */ 1420 .name = "Active Imaging AIMMS", 1421 .video_inputs = 1, 1422 /* .audio_inputs= 0, */ 1423 .tuner_type = TUNER_ABSENT, 1424 .tuner_addr = ADDR_UNSET, 1425 .pll = PLL_28, 1426 .muxsel = MUXSEL(2), 1427 .gpiomask = 0 1428 }, 1429 [BTTV_BOARD_PV_BT878P_PLUS] = { 1430 /* Tomasz Pyra <hellfire@sedez.iq.pl> */ 1431 .name = "Prolink Pixelview PV-BT878P+ (Rev.4C,8E)", 1432 .video_inputs = 3, 1433 /* .audio_inputs= 4, */ 1434 .svhs = 2, 1435 .gpiomask = 15, 1436 .muxsel = MUXSEL(2, 3, 1, 1), 1437 .gpiomux = { 0, 0, 11, 7 }, /* TV and Radio with same GPIO ! */ 1438 .gpiomute = 13, 1439 .pll = PLL_28, 1440 .tuner_type = TUNER_LG_PAL_I_FM, 1441 .tuner_addr = ADDR_UNSET, 1442 .has_remote = 1, 1443 /* GPIO wiring: 1444 GPIO0: U4.A0 (hef4052bt) 1445 GPIO1: U4.A1 1446 GPIO2: U4.A1 (second hef4052bt) 1447 GPIO3: U4.nEN, U5.A0, A5.nEN 1448 GPIO8-15: vrd866b ? 1449 */ 1450 }, 1451 [BTTV_BOARD_FLYVIDEO98EZ] = { 1452 .name = "Lifeview FlyVideo 98EZ (capture only) LR51", 1453 .video_inputs = 4, 1454 /* .audio_inputs= 0, */ 1455 .svhs = 2, 1456 /* AV1, AV2, SVHS, CVid adapter on SVHS */ 1457 .muxsel = MUXSEL(2, 3, 1, 1), 1458 .pll = PLL_28, 1459 .no_msp34xx = 1, 1460 .tuner_type = TUNER_ABSENT, 1461 .tuner_addr = ADDR_UNSET, 1462 }, 1463 1464 /* ---- card 0x48 ---------------------------------- */ 1465 [BTTV_BOARD_PV_BT878P_9B] = { 1466 /* Dariusz Kowalewski <darekk@automex.pl> */ 1467 .name = "Prolink Pixelview PV-BT878P+9B (PlayTV Pro rev.9B FM+NICAM)", 1468 .video_inputs = 4, 1469 /* .audio_inputs= 1, */ 1470 .svhs = 2, 1471 .gpiomask = 0x3f, 1472 .muxsel = MUXSEL(2, 3, 1, 1), 1473 .gpiomux = { 0x01, 0x00, 0x03, 0x03 }, 1474 .gpiomute = 0x09, 1475 .no_msp34xx = 1, 1476 .pll = PLL_28, 1477 .tuner_type = TUNER_PHILIPS_PAL, 1478 .tuner_addr = ADDR_UNSET, 1479 .audio_mode_gpio= pvbt878p9b_audio, /* Note: not all cards have stereo */ 1480 .has_radio = 1, /* Note: not all cards have radio */ 1481 .has_remote = 1, 1482 /* GPIO wiring: 1483 GPIO0: A0 hef4052 1484 GPIO1: A1 hef4052 1485 GPIO3: nEN hef4052 1486 GPIO8-15: vrd866b 1487 GPIO20,22,23: R30,R29,R28 1488 */ 1489 }, 1490 [BTTV_BOARD_SENSORAY311_611] = { 1491 /* Clay Kunz <ckunz@mail.arc.nasa.gov> */ 1492 /* you must jumper JP5 for the 311 card (PC/104+) to work */ 1493 .name = "Sensoray 311/611", 1494 .video_inputs = 5, 1495 /* .audio_inputs= 0, */ 1496 .svhs = 4, 1497 .gpiomask = 0, 1498 .muxsel = MUXSEL(2, 3, 1, 0, 0), 1499 .gpiomux = { 0 }, 1500 .tuner_type = TUNER_ABSENT, 1501 .tuner_addr = ADDR_UNSET, 1502 }, 1503 [BTTV_BOARD_RV605] = { 1504 /* Miguel Freitas <miguel@cetuc.puc-rio.br> */ 1505 .name = "RemoteVision MX (RV605)", 1506 .video_inputs = 16, 1507 /* .audio_inputs= 0, */ 1508 .svhs = NO_SVHS, 1509 .gpiomask = 0x00, 1510 .gpiomask2 = 0x07ff, 1511 .muxsel = MUXSEL(3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3), 1512 .no_msp34xx = 1, 1513 .tuner_type = TUNER_ABSENT, 1514 .tuner_addr = ADDR_UNSET, 1515 .muxsel_hook = rv605_muxsel, 1516 }, 1517 [BTTV_BOARD_POWERCLR_MTV878] = { 1518 .name = "Powercolor MTV878/ MTV878R/ MTV878F", 1519 .video_inputs = 3, 1520 /* .audio_inputs= 2, */ 1521 .svhs = 2, 1522 .gpiomask = 0x1C800F, /* Bit0-2: Audio select, 8-12:remote control 14:remote valid 15:remote reset */ 1523 .muxsel = MUXSEL(2, 1, 1), 1524 .gpiomux = { 0, 1, 2, 2 }, 1525 .gpiomute = 4, 1526 .tuner_type = TUNER_PHILIPS_PAL, 1527 .tuner_addr = ADDR_UNSET, 1528 .pll = PLL_28, 1529 .has_radio = 1, 1530 }, 1531 1532 /* ---- card 0x4c ---------------------------------- */ 1533 [BTTV_BOARD_WINDVR] = { 1534 /* Masaki Suzuki <masaki@btree.org> */ 1535 .name = "Canopus WinDVR PCI (COMPAQ Presario 3524JP, 5112JP)", 1536 .video_inputs = 3, 1537 /* .audio_inputs= 1, */ 1538 .svhs = 2, 1539 .gpiomask = 0x140007, 1540 .muxsel = MUXSEL(2, 3, 1, 1), 1541 .gpiomux = { 0, 1, 2, 3 }, 1542 .gpiomute = 4, 1543 .tuner_type = TUNER_PHILIPS_NTSC, 1544 .tuner_addr = ADDR_UNSET, 1545 .audio_mode_gpio= windvr_audio, 1546 }, 1547 [BTTV_BOARD_GRANDTEC_MULTI] = { 1548 .name = "GrandTec Multi Capture Card (Bt878)", 1549 .video_inputs = 4, 1550 /* .audio_inputs= 0, */ 1551 .svhs = NO_SVHS, 1552 .gpiomask = 0, 1553 .muxsel = MUXSEL(2, 3, 1, 0), 1554 .gpiomux = { 0 }, 1555 .no_msp34xx = 1, 1556 .pll = PLL_28, 1557 .tuner_type = TUNER_ABSENT, 1558 .tuner_addr = ADDR_UNSET, 1559 }, 1560 [BTTV_BOARD_KWORLD] = { 1561 .name = "Jetway TV/Capture JW-TV878-FBK, Kworld KW-TV878RF", 1562 .video_inputs = 4, 1563 /* .audio_inputs= 3, */ 1564 .svhs = 2, 1565 .gpiomask = 7, 1566 /* Tuner, SVid, SVHS, SVid to SVHS connector */ 1567 .muxsel = MUXSEL(2, 3, 1, 1), 1568 .gpiomux = { 0, 0, 4, 4 },/* Yes, this tuner uses the same audio output for TV and FM radio! 1569 * This card lacks external Audio In, so we mute it on Ext. & Int. 1570 * The PCB can take a sbx1637/sbx1673, wiring unknown. 1571 * This card lacks PCI subsystem ID, sigh. 1572 * gpiomux =1: lower volume, 2+3: mute 1573 * btwincap uses 0x80000/0x80003 1574 */ 1575 .gpiomute = 4, 1576 .no_msp34xx = 1, 1577 .pll = PLL_28, 1578 .tuner_type = TUNER_PHILIPS_PAL, 1579 .tuner_addr = ADDR_UNSET, 1580 /* Samsung TCPA9095PC27A (BG+DK), philips compatible, w/FM, stereo and 1581 radio signal strength indicators work fine. */ 1582 .has_radio = 1, 1583 /* GPIO Info: 1584 GPIO0,1: HEF4052 A0,A1 1585 GPIO2: HEF4052 nENABLE 1586 GPIO3-7: n.c. 1587 GPIO8-13: IRDC357 data0-5 (data6 n.c. ?) [chip not present on my card] 1588 GPIO14,15: ?? 1589 GPIO16-21: n.c. 1590 GPIO22,23: ?? 1591 ?? : mtu8b56ep microcontroller for IR (GPIO wiring unknown)*/ 1592 }, 1593 [BTTV_BOARD_DSP_TCVIDEO] = { 1594 /* Arthur Tetzlaff-Deas, DSP Design Ltd <software@dspdesign.com> */ 1595 .name = "DSP Design TCVIDEO", 1596 .video_inputs = 4, 1597 .svhs = NO_SVHS, 1598 .muxsel = MUXSEL(2, 3, 1, 0), 1599 .pll = PLL_28, 1600 .tuner_type = UNSET, 1601 .tuner_addr = ADDR_UNSET, 1602 }, 1603 1604 /* ---- card 0x50 ---------------------------------- */ 1605 [BTTV_BOARD_HAUPPAUGEPVR] = { 1606 .name = "Hauppauge WinTV PVR", 1607 .video_inputs = 4, 1608 /* .audio_inputs= 1, */ 1609 .svhs = 2, 1610 .muxsel = MUXSEL(2, 0, 1, 1), 1611 .pll = PLL_28, 1612 .tuner_type = UNSET, 1613 .tuner_addr = ADDR_UNSET, 1614 1615 .gpiomask = 7, 1616 .gpiomux = {7}, 1617 }, 1618 [BTTV_BOARD_GVBCTV5PCI] = { 1619 .name = "IODATA GV-BCTV5/PCI", 1620 .video_inputs = 3, 1621 /* .audio_inputs= 1, */ 1622 .svhs = 2, 1623 .gpiomask = 0x0f0f80, 1624 .muxsel = MUXSEL(2, 3, 1, 0), 1625 .gpiomux = {0x030000, 0x010000, 0, 0 }, 1626 .gpiomute = 0x020000, 1627 .no_msp34xx = 1, 1628 .pll = PLL_28, 1629 .tuner_type = TUNER_PHILIPS_NTSC_M, 1630 .tuner_addr = ADDR_UNSET, 1631 .audio_mode_gpio= gvbctv5pci_audio, 1632 .has_radio = 1, 1633 }, 1634 [BTTV_BOARD_OSPREY1x0] = { 1635 .name = "Osprey 100/150 (878)", /* 0x1(2|3)-45C6-C1 */ 1636 .video_inputs = 4, /* id-inputs-clock */ 1637 /* .audio_inputs= 0, */ 1638 .svhs = 3, 1639 .muxsel = MUXSEL(3, 2, 0, 1), 1640 .pll = PLL_28, 1641 .tuner_type = TUNER_ABSENT, 1642 .tuner_addr = ADDR_UNSET, 1643 .no_msp34xx = 1, 1644 .no_tda7432 = 1, 1645 }, 1646 [BTTV_BOARD_OSPREY1x0_848] = { 1647 .name = "Osprey 100/150 (848)", /* 0x04-54C0-C1 & older boards */ 1648 .video_inputs = 3, 1649 /* .audio_inputs= 0, */ 1650 .svhs = 2, 1651 .muxsel = MUXSEL(2, 3, 1), 1652 .pll = PLL_28, 1653 .tuner_type = TUNER_ABSENT, 1654 .tuner_addr = ADDR_UNSET, 1655 .no_msp34xx = 1, 1656 .no_tda7432 = 1, 1657 }, 1658 1659 /* ---- card 0x54 ---------------------------------- */ 1660 [BTTV_BOARD_OSPREY101_848] = { 1661 .name = "Osprey 101 (848)", /* 0x05-40C0-C1 */ 1662 .video_inputs = 2, 1663 /* .audio_inputs= 0, */ 1664 .svhs = 1, 1665 .muxsel = MUXSEL(3, 1), 1666 .pll = PLL_28, 1667 .tuner_type = TUNER_ABSENT, 1668 .tuner_addr = ADDR_UNSET, 1669 .no_msp34xx = 1, 1670 .no_tda7432 = 1, 1671 }, 1672 [BTTV_BOARD_OSPREY1x1] = { 1673 .name = "Osprey 101/151", /* 0x1(4|5)-0004-C4 */ 1674 .video_inputs = 1, 1675 /* .audio_inputs= 0, */ 1676 .svhs = NO_SVHS, 1677 .muxsel = MUXSEL(0), 1678 .pll = PLL_28, 1679 .tuner_type = TUNER_ABSENT, 1680 .tuner_addr = ADDR_UNSET, 1681 .no_msp34xx = 1, 1682 .no_tda7432 = 1, 1683 }, 1684 [BTTV_BOARD_OSPREY1x1_SVID] = { 1685 .name = "Osprey 101/151 w/ svid", /* 0x(16|17|20)-00C4-C1 */ 1686 .video_inputs = 2, 1687 /* .audio_inputs= 0, */ 1688 .svhs = 1, 1689 .muxsel = MUXSEL(0, 1), 1690 .pll = PLL_28, 1691 .tuner_type = TUNER_ABSENT, 1692 .tuner_addr = ADDR_UNSET, 1693 .no_msp34xx = 1, 1694 .no_tda7432 = 1, 1695 }, 1696 [BTTV_BOARD_OSPREY2xx] = { 1697 .name = "Osprey 200/201/250/251", /* 0x1(8|9|E|F)-0004-C4 */ 1698 .video_inputs = 1, 1699 /* .audio_inputs= 1, */ 1700 .svhs = NO_SVHS, 1701 .muxsel = MUXSEL(0), 1702 .pll = PLL_28, 1703 .tuner_type = TUNER_ABSENT, 1704 .tuner_addr = ADDR_UNSET, 1705 .no_msp34xx = 1, 1706 .no_tda7432 = 1, 1707 }, 1708 1709 /* ---- card 0x58 ---------------------------------- */ 1710 [BTTV_BOARD_OSPREY2x0_SVID] = { 1711 .name = "Osprey 200/250", /* 0x1(A|B)-00C4-C1 */ 1712 .video_inputs = 2, 1713 /* .audio_inputs= 1, */ 1714 .svhs = 1, 1715 .muxsel = MUXSEL(0, 1), 1716 .pll = PLL_28, 1717 .tuner_type = TUNER_ABSENT, 1718 .tuner_addr = ADDR_UNSET, 1719 .no_msp34xx = 1, 1720 .no_tda7432 = 1, 1721 }, 1722 [BTTV_BOARD_OSPREY2x0] = { 1723 .name = "Osprey 210/220/230", /* 0x1(A|B)-04C0-C1 */ 1724 .video_inputs = 2, 1725 /* .audio_inputs= 1, */ 1726 .svhs = 1, 1727 .muxsel = MUXSEL(2, 3), 1728 .pll = PLL_28, 1729 .tuner_type = TUNER_ABSENT, 1730 .tuner_addr = ADDR_UNSET, 1731 .no_msp34xx = 1, 1732 .no_tda7432 = 1, 1733 }, 1734 [BTTV_BOARD_OSPREY500] = { 1735 .name = "Osprey 500", /* 500 */ 1736 .video_inputs = 2, 1737 /* .audio_inputs= 1, */ 1738 .svhs = 1, 1739 .muxsel = MUXSEL(2, 3), 1740 .pll = PLL_28, 1741 .tuner_type = TUNER_ABSENT, 1742 .tuner_addr = ADDR_UNSET, 1743 .no_msp34xx = 1, 1744 .no_tda7432 = 1, 1745 }, 1746 [BTTV_BOARD_OSPREY540] = { 1747 .name = "Osprey 540", /* 540 */ 1748 .video_inputs = 4, 1749 /* .audio_inputs= 1, */ 1750 .pll = PLL_28, 1751 .tuner_type = TUNER_ABSENT, 1752 .tuner_addr = ADDR_UNSET, 1753 .no_msp34xx = 1, 1754 .no_tda7432 = 1, 1755 }, 1756 1757 /* ---- card 0x5C ---------------------------------- */ 1758 [BTTV_BOARD_OSPREY2000] = { 1759 .name = "Osprey 2000", /* 2000 */ 1760 .video_inputs = 2, 1761 /* .audio_inputs= 1, */ 1762 .svhs = 1, 1763 .muxsel = MUXSEL(2, 3), 1764 .pll = PLL_28, 1765 .tuner_type = TUNER_ABSENT, 1766 .tuner_addr = ADDR_UNSET, 1767 .no_msp34xx = 1, 1768 .no_tda7432 = 1, /* must avoid, conflicts with the bt860 */ 1769 }, 1770 [BTTV_BOARD_IDS_EAGLE] = { 1771 /* M G Berberich <berberic@forwiss.uni-passau.de> */ 1772 .name = "IDS Eagle", 1773 .video_inputs = 4, 1774 /* .audio_inputs= 0, */ 1775 .tuner_type = TUNER_ABSENT, 1776 .tuner_addr = ADDR_UNSET, 1777 .svhs = NO_SVHS, 1778 .gpiomask = 0, 1779 .muxsel = MUXSEL(2, 2, 2, 2), 1780 .muxsel_hook = eagle_muxsel, 1781 .no_msp34xx = 1, 1782 .pll = PLL_28, 1783 }, 1784 [BTTV_BOARD_PINNACLESAT] = { 1785 .name = "Pinnacle PCTV Sat", 1786 .video_inputs = 2, 1787 /* .audio_inputs= 0, */ 1788 .svhs = 1, 1789 .tuner_type = TUNER_ABSENT, 1790 .tuner_addr = ADDR_UNSET, 1791 .no_msp34xx = 1, 1792 .no_tda7432 = 1, 1793 .muxsel = MUXSEL(3, 1), 1794 .pll = PLL_28, 1795 .no_gpioirq = 1, 1796 .has_dvb = 1, 1797 }, 1798 [BTTV_BOARD_FORMAC_PROTV] = { 1799 .name = "Formac ProTV II (bt878)", 1800 .video_inputs = 4, 1801 /* .audio_inputs= 1, */ 1802 .svhs = 3, 1803 .gpiomask = 2, 1804 /* TV, Comp1, Composite over SVID con, SVID */ 1805 .muxsel = MUXSEL(2, 3, 1, 1), 1806 .gpiomux = { 2, 2, 0, 0 }, 1807 .pll = PLL_28, 1808 .has_radio = 1, 1809 .tuner_type = TUNER_PHILIPS_PAL, 1810 .tuner_addr = ADDR_UNSET, 1811 /* sound routing: 1812 GPIO=0x00,0x01,0x03: mute (?) 1813 0x02: both TV and radio (tuner: FM1216/I) 1814 The card has onboard audio connectors labeled "cdrom" and "board", 1815 not soldered here, though unknown wiring. 1816 Card lacks: external audio in, pci subsystem id. 1817 */ 1818 }, 1819 1820 /* ---- card 0x60 ---------------------------------- */ 1821 [BTTV_BOARD_MACHTV] = { 1822 .name = "MachTV", 1823 .video_inputs = 3, 1824 /* .audio_inputs= 1, */ 1825 .svhs = NO_SVHS, 1826 .gpiomask = 7, 1827 .muxsel = MUXSEL(2, 3, 1, 1), 1828 .gpiomux = { 0, 1, 2, 3}, 1829 .gpiomute = 4, 1830 .tuner_type = TUNER_PHILIPS_PAL, 1831 .tuner_addr = ADDR_UNSET, 1832 .pll = PLL_28, 1833 }, 1834 [BTTV_BOARD_EURESYS_PICOLO] = { 1835 .name = "Euresys Picolo", 1836 .video_inputs = 3, 1837 /* .audio_inputs= 0, */ 1838 .svhs = 2, 1839 .gpiomask = 0, 1840 .no_msp34xx = 1, 1841 .no_tda7432 = 1, 1842 .muxsel = MUXSEL(2, 0, 1), 1843 .pll = PLL_28, 1844 .tuner_type = TUNER_ABSENT, 1845 .tuner_addr = ADDR_UNSET, 1846 }, 1847 [BTTV_BOARD_PV150] = { 1848 /* Luc Van Hoeylandt <luc@e-magic.be> */ 1849 .name = "ProVideo PV150", /* 0x4f */ 1850 .video_inputs = 2, 1851 /* .audio_inputs= 0, */ 1852 .svhs = NO_SVHS, 1853 .gpiomask = 0, 1854 .muxsel = MUXSEL(2, 3), 1855 .gpiomux = { 0 }, 1856 .no_msp34xx = 1, 1857 .pll = PLL_28, 1858 .tuner_type = TUNER_ABSENT, 1859 .tuner_addr = ADDR_UNSET, 1860 }, 1861 [BTTV_BOARD_AD_TVK503] = { 1862 /* Hiroshi Takekawa <sian@big.or.jp> */ 1863 /* This card lacks subsystem ID */ 1864 .name = "AD-TVK503", /* 0x63 */ 1865 .video_inputs = 4, 1866 /* .audio_inputs= 1, */ 1867 .svhs = 2, 1868 .gpiomask = 0x001e8007, 1869 .muxsel = MUXSEL(2, 3, 1, 0), 1870 /* Tuner, Radio, external, internal, off, on */ 1871 .gpiomux = { 0x08, 0x0f, 0x0a, 0x08 }, 1872 .gpiomute = 0x0f, 1873 .no_msp34xx = 1, 1874 .pll = PLL_28, 1875 .tuner_type = TUNER_PHILIPS_NTSC, 1876 .tuner_addr = ADDR_UNSET, 1877 .audio_mode_gpio= adtvk503_audio, 1878 }, 1879 1880 /* ---- card 0x64 ---------------------------------- */ 1881 [BTTV_BOARD_HERCULES_SM_TV] = { 1882 .name = "Hercules Smart TV Stereo", 1883 .video_inputs = 4, 1884 /* .audio_inputs= 1, */ 1885 .svhs = 2, 1886 .gpiomask = 0x00, 1887 .muxsel = MUXSEL(2, 3, 1, 1), 1888 .no_msp34xx = 1, 1889 .pll = PLL_28, 1890 .tuner_type = TUNER_PHILIPS_PAL, 1891 .tuner_addr = ADDR_UNSET, 1892 /* Notes: 1893 - card lacks subsystem ID 1894 - stereo variant w/ daughter board with tda9874a @0xb0 1895 - Audio Routing: 1896 always from tda9874 independent of GPIO (?) 1897 external line in: unknown 1898 - Other chips: em78p156elp @ 0x96 (probably IR remote control) 1899 hef4053 (instead 4052) for unknown function 1900 */ 1901 }, 1902 [BTTV_BOARD_PACETV] = { 1903 .name = "Pace TV & Radio Card", 1904 .video_inputs = 4, 1905 /* .audio_inputs= 1, */ 1906 .svhs = 2, 1907 /* Tuner, CVid, SVid, CVid over SVid connector */ 1908 .muxsel = MUXSEL(2, 3, 1, 1), 1909 .gpiomask = 0, 1910 .no_tda7432 = 1, 1911 .tuner_type = TUNER_PHILIPS_PAL_I, 1912 .tuner_addr = ADDR_UNSET, 1913 .has_radio = 1, 1914 .pll = PLL_28, 1915 /* Bt878, Bt832, FI1246 tuner; no pci subsystem id 1916 only internal line out: (4pin header) RGGL 1917 Radio must be decoded by msp3410d (not routed through)*/ 1918 /* 1919 .digital_mode = DIGITAL_MODE_CAMERA, todo! 1920 */ 1921 }, 1922 [BTTV_BOARD_IVC200] = { 1923 /* Chris Willing <chris@vislab.usyd.edu.au> */ 1924 .name = "IVC-200", 1925 .video_inputs = 1, 1926 /* .audio_inputs= 0, */ 1927 .tuner_type = TUNER_ABSENT, 1928 .tuner_addr = ADDR_UNSET, 1929 .svhs = NO_SVHS, 1930 .gpiomask = 0xdf, 1931 .muxsel = MUXSEL(2), 1932 .pll = PLL_28, 1933 }, 1934 [BTTV_BOARD_IVCE8784] = { 1935 .name = "IVCE-8784", 1936 .video_inputs = 1, 1937 /* .audio_inputs= 0, */ 1938 .tuner_type = TUNER_ABSENT, 1939 .tuner_addr = ADDR_UNSET, 1940 .svhs = NO_SVHS, 1941 .gpiomask = 0xdf, 1942 .muxsel = MUXSEL(2), 1943 .pll = PLL_28, 1944 }, 1945 [BTTV_BOARD_XGUARD] = { 1946 .name = "Grand X-Guard / Trust 814PCI", 1947 .video_inputs = 16, 1948 /* .audio_inputs= 0, */ 1949 .svhs = NO_SVHS, 1950 .tuner_type = TUNER_ABSENT, 1951 .tuner_addr = ADDR_UNSET, 1952 .gpiomask2 = 0xff, 1953 .muxsel = MUXSEL(2,2,2,2, 3,3,3,3, 1,1,1,1, 0,0,0,0), 1954 .muxsel_hook = xguard_muxsel, 1955 .no_msp34xx = 1, 1956 .no_tda7432 = 1, 1957 .pll = PLL_28, 1958 }, 1959 1960 /* ---- card 0x68 ---------------------------------- */ 1961 [BTTV_BOARD_NEBULA_DIGITV] = { 1962 .name = "Nebula Electronics DigiTV", 1963 .video_inputs = 1, 1964 .svhs = NO_SVHS, 1965 .muxsel = MUXSEL(2, 3, 1, 0), 1966 .no_msp34xx = 1, 1967 .no_tda7432 = 1, 1968 .pll = PLL_28, 1969 .tuner_type = TUNER_ABSENT, 1970 .tuner_addr = ADDR_UNSET, 1971 .has_dvb = 1, 1972 .has_remote = 1, 1973 .gpiomask = 0x1b, 1974 .no_gpioirq = 1, 1975 }, 1976 [BTTV_BOARD_PV143] = { 1977 /* Jorge Boncompte - DTI2 <jorge@dti2.net> */ 1978 .name = "ProVideo PV143", 1979 .video_inputs = 4, 1980 /* .audio_inputs= 0, */ 1981 .svhs = NO_SVHS, 1982 .gpiomask = 0, 1983 .muxsel = MUXSEL(2, 3, 1, 0), 1984 .gpiomux = { 0 }, 1985 .no_msp34xx = 1, 1986 .pll = PLL_28, 1987 .tuner_type = TUNER_ABSENT, 1988 .tuner_addr = ADDR_UNSET, 1989 }, 1990 [BTTV_BOARD_VD009X1_VD011_MINIDIN] = { 1991 /* M.Klahr@phytec.de */ 1992 .name = "PHYTEC VD-009-X1 VD-011 MiniDIN (bt878)", 1993 .video_inputs = 4, 1994 /* .audio_inputs= 0, */ 1995 .svhs = 3, 1996 .gpiomask = 0x00, 1997 .muxsel = MUXSEL(2, 3, 1, 0), 1998 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */ 1999 .pll = PLL_28, 2000 .tuner_type = TUNER_ABSENT, 2001 .tuner_addr = ADDR_UNSET, 2002 }, 2003 [BTTV_BOARD_VD009X1_VD011_COMBI] = { 2004 .name = "PHYTEC VD-009-X1 VD-011 Combi (bt878)", 2005 .video_inputs = 4, 2006 /* .audio_inputs= 0, */ 2007 .svhs = 3, 2008 .gpiomask = 0x00, 2009 .muxsel = MUXSEL(2, 3, 1, 1), 2010 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */ 2011 .pll = PLL_28, 2012 .tuner_type = TUNER_ABSENT, 2013 .tuner_addr = ADDR_UNSET, 2014 }, 2015 2016 /* ---- card 0x6c ---------------------------------- */ 2017 [BTTV_BOARD_VD009_MINIDIN] = { 2018 .name = "PHYTEC VD-009 MiniDIN (bt878)", 2019 .video_inputs = 10, 2020 /* .audio_inputs= 0, */ 2021 .svhs = 9, 2022 .gpiomask = 0x00, 2023 .gpiomask2 = 0x03, /* used for external vodeo mux */ 2024 .muxsel = MUXSEL(2, 2, 2, 2, 3, 3, 3, 3, 1, 0), 2025 .muxsel_hook = phytec_muxsel, 2026 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */ 2027 .pll = PLL_28, 2028 .tuner_type = TUNER_ABSENT, 2029 .tuner_addr = ADDR_UNSET, 2030 }, 2031 [BTTV_BOARD_VD009_COMBI] = { 2032 .name = "PHYTEC VD-009 Combi (bt878)", 2033 .video_inputs = 10, 2034 /* .audio_inputs= 0, */ 2035 .svhs = 9, 2036 .gpiomask = 0x00, 2037 .gpiomask2 = 0x03, /* used for external vodeo mux */ 2038 .muxsel = MUXSEL(2, 2, 2, 2, 3, 3, 3, 3, 1, 1), 2039 .muxsel_hook = phytec_muxsel, 2040 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */ 2041 .pll = PLL_28, 2042 .tuner_type = TUNER_ABSENT, 2043 .tuner_addr = ADDR_UNSET, 2044 }, 2045 [BTTV_BOARD_IVC100] = { 2046 .name = "IVC-100", 2047 .video_inputs = 4, 2048 /* .audio_inputs= 0, */ 2049 .tuner_type = TUNER_ABSENT, 2050 .tuner_addr = ADDR_UNSET, 2051 .svhs = NO_SVHS, 2052 .gpiomask = 0xdf, 2053 .muxsel = MUXSEL(2, 3, 1, 0), 2054 .pll = PLL_28, 2055 }, 2056 [BTTV_BOARD_IVC120] = { 2057 /* IVC-120G - Alan Garfield <alan@fromorbit.com> */ 2058 .name = "IVC-120G", 2059 .video_inputs = 16, 2060 /* .audio_inputs= 0, */ 2061 .tuner_type = TUNER_ABSENT, 2062 .tuner_addr = ADDR_UNSET, 2063 .svhs = NO_SVHS, /* card has no svhs */ 2064 .no_msp34xx = 1, 2065 .no_tda7432 = 1, 2066 .gpiomask = 0x00, 2067 .muxsel = MUXSEL(0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0), 2068 .muxsel_hook = ivc120_muxsel, 2069 .pll = PLL_28, 2070 }, 2071 2072 /* ---- card 0x70 ---------------------------------- */ 2073 [BTTV_BOARD_PC_HDTV] = { 2074 .name = "pcHDTV HD-2000 TV", 2075 .video_inputs = 4, 2076 /* .audio_inputs= 1, */ 2077 .svhs = 2, 2078 .muxsel = MUXSEL(2, 3, 1, 0), 2079 .tuner_type = TUNER_PHILIPS_FCV1236D, 2080 .tuner_addr = ADDR_UNSET, 2081 .has_dvb = 1, 2082 }, 2083 [BTTV_BOARD_TWINHAN_DST] = { 2084 .name = "Twinhan DST + clones", 2085 .no_msp34xx = 1, 2086 .no_tda7432 = 1, 2087 .tuner_type = TUNER_ABSENT, 2088 .tuner_addr = ADDR_UNSET, 2089 .no_video = 1, 2090 .has_dvb = 1, 2091 }, 2092 [BTTV_BOARD_WINFASTVC100] = { 2093 .name = "Winfast VC100", 2094 .video_inputs = 3, 2095 /* .audio_inputs= 0, */ 2096 .svhs = 1, 2097 /* Vid In, SVid In, Vid over SVid in connector */ 2098 .muxsel = MUXSEL(3, 1, 1, 3), 2099 .no_msp34xx = 1, 2100 .no_tda7432 = 1, 2101 .tuner_type = TUNER_ABSENT, 2102 .tuner_addr = ADDR_UNSET, 2103 .pll = PLL_28, 2104 }, 2105 [BTTV_BOARD_TEV560] = { 2106 .name = "Teppro TEV-560/InterVision IV-560", 2107 .video_inputs = 3, 2108 /* .audio_inputs= 1, */ 2109 .svhs = 2, 2110 .gpiomask = 3, 2111 .muxsel = MUXSEL(2, 3, 1, 1), 2112 .gpiomux = { 1, 1, 1, 1 }, 2113 .tuner_type = TUNER_PHILIPS_PAL, 2114 .tuner_addr = ADDR_UNSET, 2115 .pll = PLL_35, 2116 }, 2117 2118 /* ---- card 0x74 ---------------------------------- */ 2119 [BTTV_BOARD_SIMUS_GVC1100] = { 2120 .name = "SIMUS GVC1100", 2121 .video_inputs = 4, 2122 /* .audio_inputs= 0, */ 2123 .svhs = NO_SVHS, 2124 .tuner_type = TUNER_ABSENT, 2125 .tuner_addr = ADDR_UNSET, 2126 .pll = PLL_28, 2127 .muxsel = MUXSEL(2, 2, 2, 2), 2128 .gpiomask = 0x3F, 2129 .muxsel_hook = gvc1100_muxsel, 2130 }, 2131 [BTTV_BOARD_NGSTV_PLUS] = { 2132 /* Carlos Silva r3pek@r3pek.homelinux.org || card 0x75 */ 2133 .name = "NGS NGSTV+", 2134 .video_inputs = 3, 2135 .svhs = 2, 2136 .gpiomask = 0x008007, 2137 .muxsel = MUXSEL(2, 3, 0, 0), 2138 .gpiomux = { 0, 0, 0, 0 }, 2139 .gpiomute = 0x000003, 2140 .pll = PLL_28, 2141 .tuner_type = TUNER_PHILIPS_PAL, 2142 .tuner_addr = ADDR_UNSET, 2143 .has_remote = 1, 2144 }, 2145 [BTTV_BOARD_LMLBT4] = { 2146 /* http://linuxmedialabs.com */ 2147 .name = "LMLBT4", 2148 .video_inputs = 4, /* IN1,IN2,IN3,IN4 */ 2149 /* .audio_inputs= 0, */ 2150 .svhs = NO_SVHS, 2151 .muxsel = MUXSEL(2, 3, 1, 0), 2152 .no_msp34xx = 1, 2153 .no_tda7432 = 1, 2154 .tuner_type = TUNER_ABSENT, 2155 .tuner_addr = ADDR_UNSET, 2156 }, 2157 [BTTV_BOARD_TEKRAM_M205] = { 2158 /* Helmroos Harri <harri.helmroos@pp.inet.fi> */ 2159 .name = "Tekram M205 PRO", 2160 .video_inputs = 3, 2161 /* .audio_inputs= 1, */ 2162 .tuner_type = TUNER_PHILIPS_PAL, 2163 .tuner_addr = ADDR_UNSET, 2164 .svhs = 2, 2165 .gpiomask = 0x68, 2166 .muxsel = MUXSEL(2, 3, 1), 2167 .gpiomux = { 0x68, 0x68, 0x61, 0x61 }, 2168 .pll = PLL_28, 2169 }, 2170 2171 /* ---- card 0x78 ---------------------------------- */ 2172 [BTTV_BOARD_CONTVFMI] = { 2173 /* Javier Cendan Ares <jcendan@lycos.es> */ 2174 /* bt878 TV + FM without subsystem ID */ 2175 .name = "Conceptronic CONTVFMi", 2176 .video_inputs = 3, 2177 /* .audio_inputs= 1, */ 2178 .svhs = 2, 2179 .gpiomask = 0x008007, 2180 .muxsel = MUXSEL(2, 3, 1, 1), 2181 .gpiomux = { 0, 1, 2, 2 }, 2182 .gpiomute = 3, 2183 .pll = PLL_28, 2184 .tuner_type = TUNER_PHILIPS_PAL, 2185 .tuner_addr = ADDR_UNSET, 2186 .has_remote = 1, 2187 .has_radio = 1, 2188 }, 2189 [BTTV_BOARD_PICOLO_TETRA_CHIP] = { 2190 /*Eric DEBIEF <debief@telemsa.com>*/ 2191 /*EURESYS Picolo Tetra : 4 Conexant Fusion 878A, no audio, video input set with analog multiplexers GPIO controlled*/ 2192 /* adds picolo_tetra_muxsel(), picolo_tetra_init(), the following declaration strucure, and #define BTTV_BOARD_PICOLO_TETRA_CHIP*/ 2193 /*0x79 in bttv.h*/ 2194 .name = "Euresys Picolo Tetra", 2195 .video_inputs = 4, 2196 /* .audio_inputs= 0, */ 2197 .svhs = NO_SVHS, 2198 .gpiomask = 0, 2199 .gpiomask2 = 0x3C<<16,/*Set the GPIO[18]->GPIO[21] as output pin.==> drive the video inputs through analog multiplexers*/ 2200 .no_msp34xx = 1, 2201 .no_tda7432 = 1, 2202 /*878A input is always MUX0, see above.*/ 2203 .muxsel = MUXSEL(2, 2, 2, 2), 2204 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */ 2205 .pll = PLL_28, 2206 .muxsel_hook = picolo_tetra_muxsel,/*Required as it doesn't follow the classic input selection policy*/ 2207 .tuner_type = TUNER_ABSENT, 2208 .tuner_addr = ADDR_UNSET, 2209 }, 2210 [BTTV_BOARD_SPIRIT_TV] = { 2211 /* Spirit TV Tuner from http://spiritmodems.com.au */ 2212 /* Stafford Goodsell <surge@goliath.homeunix.org> */ 2213 .name = "Spirit TV Tuner", 2214 .video_inputs = 3, 2215 /* .audio_inputs= 1, */ 2216 .svhs = 2, 2217 .gpiomask = 0x0000000f, 2218 .muxsel = MUXSEL(2, 1, 1), 2219 .gpiomux = { 0x02, 0x00, 0x00, 0x00 }, 2220 .tuner_type = TUNER_TEMIC_PAL, 2221 .tuner_addr = ADDR_UNSET, 2222 .no_msp34xx = 1, 2223 }, 2224 [BTTV_BOARD_AVDVBT_771] = { 2225 /* Wolfram Joost <wojo@frokaschwei.de> */ 2226 .name = "AVerMedia AVerTV DVB-T 771", 2227 .video_inputs = 2, 2228 .svhs = 1, 2229 .tuner_type = TUNER_ABSENT, 2230 .tuner_addr = ADDR_UNSET, 2231 .muxsel = MUXSEL(3, 3), 2232 .no_msp34xx = 1, 2233 .no_tda7432 = 1, 2234 .pll = PLL_28, 2235 .has_dvb = 1, 2236 .no_gpioirq = 1, 2237 .has_remote = 1, 2238 }, 2239 /* ---- card 0x7c ---------------------------------- */ 2240 [BTTV_BOARD_AVDVBT_761] = { 2241 /* Matt Jesson <dvb@jesson.eclipse.co.uk> */ 2242 /* Based on the Nebula card data - added remote and new card number - BTTV_BOARD_AVDVBT_761, see also ir-kbd-gpio.c */ 2243 .name = "AverMedia AverTV DVB-T 761", 2244 .video_inputs = 2, 2245 .svhs = 1, 2246 .muxsel = MUXSEL(3, 1, 2, 0), /* Comp0, S-Video, ?, ? */ 2247 .no_msp34xx = 1, 2248 .no_tda7432 = 1, 2249 .pll = PLL_28, 2250 .tuner_type = TUNER_ABSENT, 2251 .tuner_addr = ADDR_UNSET, 2252 .has_dvb = 1, 2253 .no_gpioirq = 1, 2254 .has_remote = 1, 2255 }, 2256 [BTTV_BOARD_MATRIX_VISIONSQ] = { 2257 /* andre.schwarz@matrix-vision.de */ 2258 .name = "MATRIX Vision Sigma-SQ", 2259 .video_inputs = 16, 2260 /* .audio_inputs= 0, */ 2261 .svhs = NO_SVHS, 2262 .gpiomask = 0x0, 2263 .muxsel = MUXSEL(2, 2, 2, 2, 2, 2, 2, 2, 3, 3, 3, 3, 3, 3, 3, 3), 2264 .muxsel_hook = sigmaSQ_muxsel, 2265 .gpiomux = { 0 }, 2266 .no_msp34xx = 1, 2267 .pll = PLL_28, 2268 .tuner_type = TUNER_ABSENT, 2269 .tuner_addr = ADDR_UNSET, 2270 }, 2271 [BTTV_BOARD_MATRIX_VISIONSLC] = { 2272 /* andre.schwarz@matrix-vision.de */ 2273 .name = "MATRIX Vision Sigma-SLC", 2274 .video_inputs = 4, 2275 /* .audio_inputs= 0, */ 2276 .svhs = NO_SVHS, 2277 .gpiomask = 0x0, 2278 .muxsel = MUXSEL(2, 2, 2, 2), 2279 .muxsel_hook = sigmaSLC_muxsel, 2280 .gpiomux = { 0 }, 2281 .no_msp34xx = 1, 2282 .pll = PLL_28, 2283 .tuner_type = TUNER_ABSENT, 2284 .tuner_addr = ADDR_UNSET, 2285 }, 2286 /* BTTV_BOARD_APAC_VIEWCOMP */ 2287 [BTTV_BOARD_APAC_VIEWCOMP] = { 2288 /* Attila Kondoros <attila.kondoros@chello.hu> */ 2289 /* bt878 TV + FM 0x00000000 subsystem ID */ 2290 .name = "APAC Viewcomp 878(AMAX)", 2291 .video_inputs = 2, 2292 /* .audio_inputs= 1, */ 2293 .svhs = NO_SVHS, 2294 .gpiomask = 0xFF, 2295 .muxsel = MUXSEL(2, 3, 1, 1), 2296 .gpiomux = { 2, 0, 0, 0 }, 2297 .gpiomute = 10, 2298 .pll = PLL_28, 2299 .tuner_type = TUNER_PHILIPS_PAL, 2300 .tuner_addr = ADDR_UNSET, 2301 .has_remote = 1, /* miniremote works, see ir-kbd-gpio.c */ 2302 .has_radio = 1, /* not every card has radio */ 2303 }, 2304 2305 /* ---- card 0x80 ---------------------------------- */ 2306 [BTTV_BOARD_DVICO_DVBT_LITE] = { 2307 /* Chris Pascoe <c.pascoe@itee.uq.edu.au> */ 2308 .name = "DViCO FusionHDTV DVB-T Lite", 2309 .no_msp34xx = 1, 2310 .no_tda7432 = 1, 2311 .pll = PLL_28, 2312 .no_video = 1, 2313 .has_dvb = 1, 2314 .tuner_type = TUNER_ABSENT, 2315 .tuner_addr = ADDR_UNSET, 2316 }, 2317 [BTTV_BOARD_VGEAR_MYVCD] = { 2318 /* Steven <photon38@pchome.com.tw> */ 2319 .name = "V-Gear MyVCD", 2320 .video_inputs = 3, 2321 /* .audio_inputs= 1, */ 2322 .svhs = 2, 2323 .gpiomask = 0x3f, 2324 .muxsel = MUXSEL(2, 3, 1, 0), 2325 .gpiomux = {0x31, 0x31, 0x31, 0x31 }, 2326 .gpiomute = 0x31, 2327 .no_msp34xx = 1, 2328 .pll = PLL_28, 2329 .tuner_type = TUNER_PHILIPS_NTSC_M, 2330 .tuner_addr = ADDR_UNSET, 2331 .has_radio = 0, 2332 }, 2333 [BTTV_BOARD_SUPER_TV] = { 2334 /* Rick C <cryptdragoon@gmail.com> */ 2335 .name = "Super TV Tuner", 2336 .video_inputs = 4, 2337 /* .audio_inputs= 1, */ 2338 .svhs = 2, 2339 .muxsel = MUXSEL(2, 3, 1, 0), 2340 .tuner_type = TUNER_PHILIPS_NTSC, 2341 .tuner_addr = ADDR_UNSET, 2342 .gpiomask = 0x008007, 2343 .gpiomux = { 0, 0x000001,0,0 }, 2344 .has_radio = 1, 2345 }, 2346 [BTTV_BOARD_TIBET_CS16] = { 2347 /* Chris Fanning <video4linux@haydon.net> */ 2348 .name = "Tibet Systems 'Progress DVR' CS16", 2349 .video_inputs = 16, 2350 /* .audio_inputs= 0, */ 2351 .svhs = NO_SVHS, 2352 .muxsel = MUXSEL(2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2), 2353 .pll = PLL_28, 2354 .no_msp34xx = 1, 2355 .no_tda7432 = 1, 2356 .tuner_type = TUNER_ABSENT, 2357 .tuner_addr = ADDR_UNSET, 2358 .muxsel_hook = tibetCS16_muxsel, 2359 }, 2360 [BTTV_BOARD_KODICOM_4400R] = { 2361 /* Bill Brack <wbrack@mmm.com.hk> */ 2362 /* 2363 * Note that, because of the card's wiring, the "master" 2364 * BT878A chip (i.e. the one which controls the analog switch 2365 * and must use this card type) is the 2nd one detected. The 2366 * other 3 chips should use card type 0x85, whose description 2367 * follows this one. There is a EEPROM on the card (which is 2368 * connected to the I2C of one of those other chips), but is 2369 * not currently handled. There is also a facility for a 2370 * "monitor", which is also not currently implemented. 2371 */ 2372 .name = "Kodicom 4400R (master)", 2373 .video_inputs = 16, 2374 /* .audio_inputs= 0, */ 2375 .tuner_type = TUNER_ABSENT, 2376 .tuner_addr = ADDR_UNSET, 2377 .svhs = NO_SVHS, 2378 /* GPIO bits 0-9 used for analog switch: 2379 * 00 - 03: camera selector 2380 * 04 - 06: channel (controller) selector 2381 * 07: data (1->on, 0->off) 2382 * 08: strobe 2383 * 09: reset 2384 * bit 16 is input from sync separator for the channel 2385 */ 2386 .gpiomask = 0x0003ff, 2387 .no_gpioirq = 1, 2388 .muxsel = MUXSEL(3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3), 2389 .pll = PLL_28, 2390 .no_msp34xx = 1, 2391 .no_tda7432 = 1, 2392 .muxsel_hook = kodicom4400r_muxsel, 2393 }, 2394 [BTTV_BOARD_KODICOM_4400R_SL] = { 2395 /* Bill Brack <wbrack@mmm.com.hk> */ 2396 /* Note that, for reasons unknown, the "master" BT878A chip (i.e. the 2397 * one which controls the analog switch, and must use the card type) 2398 * is the 2nd one detected. The other 3 chips should use this card 2399 * type 2400 */ 2401 .name = "Kodicom 4400R (slave)", 2402 .video_inputs = 16, 2403 /* .audio_inputs= 0, */ 2404 .tuner_type = TUNER_ABSENT, 2405 .tuner_addr = ADDR_UNSET, 2406 .svhs = NO_SVHS, 2407 .gpiomask = 0x010000, 2408 .no_gpioirq = 1, 2409 .muxsel = MUXSEL(3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3), 2410 .pll = PLL_28, 2411 .no_msp34xx = 1, 2412 .no_tda7432 = 1, 2413 .muxsel_hook = kodicom4400r_muxsel, 2414 }, 2415 /* ---- card 0x86---------------------------------- */ 2416 [BTTV_BOARD_ADLINK_RTV24] = { 2417 /* Michael Henson <mhenson@clarityvi.com> */ 2418 /* Adlink RTV24 with special unlock codes */ 2419 .name = "Adlink RTV24", 2420 .video_inputs = 4, 2421 /* .audio_inputs= 1, */ 2422 .svhs = 2, 2423 .muxsel = MUXSEL(2, 3, 1, 0), 2424 .tuner_type = UNSET, 2425 .tuner_addr = ADDR_UNSET, 2426 .pll = PLL_28, 2427 }, 2428 /* ---- card 0x87---------------------------------- */ 2429 [BTTV_BOARD_DVICO_FUSIONHDTV_5_LITE] = { 2430 /* Michael Krufky <mkrufky@linuxtv.org> */ 2431 .name = "DViCO FusionHDTV 5 Lite", 2432 .tuner_type = TUNER_LG_TDVS_H06XF, /* TDVS-H064F */ 2433 .tuner_addr = ADDR_UNSET, 2434 .video_inputs = 3, 2435 /* .audio_inputs= 1, */ 2436 .svhs = 2, 2437 .muxsel = MUXSEL(2, 3, 1), 2438 .gpiomask = 0x00e00007, 2439 .gpiomux = { 0x00400005, 0, 0x00000001, 0 }, 2440 .gpiomute = 0x00c00007, 2441 .no_msp34xx = 1, 2442 .no_tda7432 = 1, 2443 .has_dvb = 1, 2444 }, 2445 /* ---- card 0x88---------------------------------- */ 2446 [BTTV_BOARD_ACORP_Y878F] = { 2447 /* Mauro Carvalho Chehab <mchehab@infradead.org> */ 2448 .name = "Acorp Y878F", 2449 .video_inputs = 3, 2450 /* .audio_inputs= 1, */ 2451 .svhs = 2, 2452 .gpiomask = 0x01fe00, 2453 .muxsel = MUXSEL(2, 3, 1, 1), 2454 .gpiomux = { 0x001e00, 0, 0x018000, 0x014000 }, 2455 .gpiomute = 0x002000, 2456 .pll = PLL_28, 2457 .tuner_type = TUNER_YMEC_TVF66T5_B_DFF, 2458 .tuner_addr = 0xc1 >>1, 2459 .has_radio = 1, 2460 }, 2461 /* ---- card 0x89 ---------------------------------- */ 2462 [BTTV_BOARD_CONCEPTRONIC_CTVFMI2] = { 2463 .name = "Conceptronic CTVFMi v2", 2464 .video_inputs = 3, 2465 /* .audio_inputs= 1, */ 2466 .svhs = 2, 2467 .gpiomask = 0x001c0007, 2468 .muxsel = MUXSEL(2, 3, 1, 1), 2469 .gpiomux = { 0, 1, 2, 2 }, 2470 .gpiomute = 3, 2471 .pll = PLL_28, 2472 .tuner_type = TUNER_TENA_9533_DI, 2473 .tuner_addr = ADDR_UNSET, 2474 .has_remote = 1, 2475 .has_radio = 1, 2476 }, 2477 /* ---- card 0x8a ---------------------------------- */ 2478 [BTTV_BOARD_PV_BT878P_2E] = { 2479 .name = "Prolink Pixelview PV-BT878P+ (Rev.2E)", 2480 .video_inputs = 5, 2481 /* .audio_inputs= 1, */ 2482 .svhs = 3, 2483 .has_dig_in = 1, 2484 .gpiomask = 0x01fe00, 2485 .muxsel = MUXSEL(2, 3, 1, 1, 0), /* in 4 is digital */ 2486 /* .digital_mode= DIGITAL_MODE_CAMERA, */ 2487 .gpiomux = { 0x00400, 0x10400, 0x04400, 0x80000 }, 2488 .gpiomute = 0x12400, 2489 .no_msp34xx = 1, 2490 .pll = PLL_28, 2491 .tuner_type = TUNER_LG_PAL_FM, 2492 .tuner_addr = ADDR_UNSET, 2493 .has_remote = 1, 2494 }, 2495 /* ---- card 0x8b ---------------------------------- */ 2496 [BTTV_BOARD_PV_M4900] = { 2497 /* Sérgio Fortier <sergiofortier@yahoo.com.br> */ 2498 .name = "Prolink PixelView PlayTV MPEG2 PV-M4900", 2499 .video_inputs = 3, 2500 /* .audio_inputs= 1, */ 2501 .svhs = 2, 2502 .gpiomask = 0x3f, 2503 .muxsel = MUXSEL(2, 3, 1, 1), 2504 .gpiomux = { 0x21, 0x20, 0x24, 0x2c }, 2505 .gpiomute = 0x29, 2506 .no_msp34xx = 1, 2507 .pll = PLL_28, 2508 .tuner_type = TUNER_YMEC_TVF_5533MF, 2509 .tuner_addr = ADDR_UNSET, 2510 .has_radio = 1, 2511 .has_remote = 1, 2512 }, 2513 /* ---- card 0x8c ---------------------------------- */ 2514 /* Has four Bt878 chips behind a PCI bridge, each chip has: 2515 one external BNC composite input (mux 2) 2516 three internal composite inputs (unknown muxes) 2517 an 18-bit stereo A/D (CS5331A), which has: 2518 one external stereo unblanced (RCA) audio connection 2519 one (or 3?) internal stereo balanced (XLR) audio connection 2520 input is selected via gpio to a 14052B mux 2521 (mask=0x300, unbal=0x000, bal=0x100, ??=0x200,0x300) 2522 gain is controlled via an X9221A chip on the I2C bus @0x28 2523 sample rate is controlled via gpio to an MK1413S 2524 (mask=0x3, 32kHz=0x0, 44.1kHz=0x1, 48kHz=0x2, ??=0x3) 2525 There is neither a tuner nor an svideo input. */ 2526 [BTTV_BOARD_OSPREY440] = { 2527 .name = "Osprey 440", 2528 .video_inputs = 4, 2529 /* .audio_inputs= 2, */ 2530 .svhs = NO_SVHS, 2531 .muxsel = MUXSEL(2, 3, 0, 1), /* 3,0,1 are guesses */ 2532 .gpiomask = 0x303, 2533 .gpiomute = 0x000, /* int + 32kHz */ 2534 .gpiomux = { 0, 0, 0x000, 0x100}, 2535 .pll = PLL_28, 2536 .tuner_type = TUNER_ABSENT, 2537 .tuner_addr = ADDR_UNSET, 2538 .no_msp34xx = 1, 2539 .no_tda7432 = 1, 2540 }, 2541 /* ---- card 0x8d ---------------------------------- */ 2542 [BTTV_BOARD_ASOUND_SKYEYE] = { 2543 .name = "Asound Skyeye PCTV", 2544 .video_inputs = 3, 2545 /* .audio_inputs= 1, */ 2546 .svhs = 2, 2547 .gpiomask = 15, 2548 .muxsel = MUXSEL(2, 3, 1, 1), 2549 .gpiomux = { 2, 0, 0, 0 }, 2550 .gpiomute = 1, 2551 .pll = PLL_28, 2552 .tuner_type = TUNER_PHILIPS_NTSC, 2553 .tuner_addr = ADDR_UNSET, 2554 }, 2555 /* ---- card 0x8e ---------------------------------- */ 2556 [BTTV_BOARD_SABRENT_TVFM] = { 2557 .name = "Sabrent TV-FM (bttv version)", 2558 .video_inputs = 3, 2559 /* .audio_inputs= 1, */ 2560 .svhs = 2, 2561 .gpiomask = 0x108007, 2562 .muxsel = MUXSEL(2, 3, 1, 1), 2563 .gpiomux = { 100000, 100002, 100002, 100000 }, 2564 .no_msp34xx = 1, 2565 .no_tda7432 = 1, 2566 .pll = PLL_28, 2567 .tuner_type = TUNER_TNF_5335MF, 2568 .tuner_addr = ADDR_UNSET, 2569 .has_radio = 1, 2570 }, 2571 /* ---- card 0x8f ---------------------------------- */ 2572 [BTTV_BOARD_HAUPPAUGE_IMPACTVCB] = { 2573 .name = "Hauppauge ImpactVCB (bt878)", 2574 .video_inputs = 4, 2575 /* .audio_inputs= 0, */ 2576 .svhs = NO_SVHS, 2577 .gpiomask = 0x0f, /* old: 7 */ 2578 .muxsel = MUXSEL(0, 1, 3, 2), /* Composite 0-3 */ 2579 .no_msp34xx = 1, 2580 .no_tda7432 = 1, 2581 .tuner_type = TUNER_ABSENT, 2582 .tuner_addr = ADDR_UNSET, 2583 }, 2584 [BTTV_BOARD_MACHTV_MAGICTV] = { 2585 /* Julian Calaby <julian.calaby@gmail.com> 2586 * Slightly different from original MachTV definition (0x60) 2587 2588 * FIXME: RegSpy says gpiomask should be "0x001c800f", but it 2589 * stuffs up remote chip. Bug is a pin on the jaecs is not set 2590 * properly (methinks) causing no keyup bits being set */ 2591 2592 .name = "MagicTV", /* rebranded MachTV */ 2593 .video_inputs = 3, 2594 /* .audio_inputs= 1, */ 2595 .svhs = 2, 2596 .gpiomask = 7, 2597 .muxsel = MUXSEL(2, 3, 1, 1), 2598 .gpiomux = { 0, 1, 2, 3 }, 2599 .gpiomute = 4, 2600 .tuner_type = TUNER_TEMIC_4009FR5_PAL, 2601 .tuner_addr = ADDR_UNSET, 2602 .pll = PLL_28, 2603 .has_radio = 1, 2604 .has_remote = 1, 2605 }, 2606 [BTTV_BOARD_SSAI_SECURITY] = { 2607 .name = "SSAI Security Video Interface", 2608 .video_inputs = 4, 2609 /* .audio_inputs= 0, */ 2610 .svhs = NO_SVHS, 2611 .muxsel = MUXSEL(0, 1, 2, 3), 2612 .tuner_type = TUNER_ABSENT, 2613 .tuner_addr = ADDR_UNSET, 2614 }, 2615 [BTTV_BOARD_SSAI_ULTRASOUND] = { 2616 .name = "SSAI Ultrasound Video Interface", 2617 .video_inputs = 2, 2618 /* .audio_inputs= 0, */ 2619 .svhs = 1, 2620 .muxsel = MUXSEL(2, 0, 1, 3), 2621 .tuner_type = TUNER_ABSENT, 2622 .tuner_addr = ADDR_UNSET, 2623 }, 2624 /* ---- card 0x94---------------------------------- */ 2625 [BTTV_BOARD_DVICO_FUSIONHDTV_2] = { 2626 .name = "DViCO FusionHDTV 2", 2627 .tuner_type = TUNER_PHILIPS_FCV1236D, 2628 .tuner_addr = ADDR_UNSET, 2629 .video_inputs = 3, 2630 /* .audio_inputs= 1, */ 2631 .svhs = 2, 2632 .muxsel = MUXSEL(2, 3, 1), 2633 .gpiomask = 0x00e00007, 2634 .gpiomux = { 0x00400005, 0, 0x00000001, 0 }, 2635 .gpiomute = 0x00c00007, 2636 .no_msp34xx = 1, 2637 .no_tda7432 = 1, 2638 }, 2639 /* ---- card 0x95---------------------------------- */ 2640 [BTTV_BOARD_TYPHOON_TVTUNERPCI] = { 2641 .name = "Typhoon TV-Tuner PCI (50684)", 2642 .video_inputs = 3, 2643 /* .audio_inputs= 1, */ 2644 .svhs = 2, 2645 .gpiomask = 0x3014f, 2646 .muxsel = MUXSEL(2, 3, 1, 1), 2647 .gpiomux = { 0x20001,0x10001, 0, 0 }, 2648 .gpiomute = 10, 2649 .pll = PLL_28, 2650 .tuner_type = TUNER_PHILIPS_PAL_I, 2651 .tuner_addr = ADDR_UNSET, 2652 }, 2653 [BTTV_BOARD_GEOVISION_GV600] = { 2654 /* emhn@usb.ve */ 2655 .name = "Geovision GV-600", 2656 .video_inputs = 16, 2657 /* .audio_inputs= 0, */ 2658 .svhs = NO_SVHS, 2659 .gpiomask = 0x0, 2660 .muxsel = MUXSEL(2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2), 2661 .muxsel_hook = geovision_muxsel, 2662 .gpiomux = { 0 }, 2663 .no_msp34xx = 1, 2664 .pll = PLL_28, 2665 .tuner_type = TUNER_ABSENT, 2666 .tuner_addr = ADDR_UNSET, 2667 }, 2668 [BTTV_BOARD_KOZUMI_KTV_01C] = { 2669 /* Mauro Lacy <mauro@lacy.com.ar> 2670 * Based on MagicTV and Conceptronic CONTVFMi */ 2671 2672 .name = "Kozumi KTV-01C", 2673 .video_inputs = 3, 2674 /* .audio_inputs= 1, */ 2675 .svhs = 2, 2676 .gpiomask = 0x008007, 2677 .muxsel = MUXSEL(2, 3, 1, 1), 2678 .gpiomux = { 0, 1, 2, 2 }, /* CONTVFMi */ 2679 .gpiomute = 3, /* CONTVFMi */ 2680 .tuner_type = TUNER_PHILIPS_FM1216ME_MK3, /* TCL MK3 */ 2681 .tuner_addr = ADDR_UNSET, 2682 .pll = PLL_28, 2683 .has_radio = 1, 2684 .has_remote = 1, 2685 }, 2686 [BTTV_BOARD_ENLTV_FM_2] = { 2687 /* Encore TV Tuner Pro ENL TV-FM-2 2688 Mauro Carvalho Chehab <mchehab@infradead.org */ 2689 .name = "Encore ENL TV-FM-2", 2690 .video_inputs = 3, 2691 /* .audio_inputs= 1, */ 2692 .svhs = 2, 2693 /* bit 6 -> IR disabled 2694 bit 18/17 = 00 -> mute 2695 01 -> enable external audio input 2696 10 -> internal audio input (mono?) 2697 11 -> internal audio input 2698 */ 2699 .gpiomask = 0x060040, 2700 .muxsel = MUXSEL(2, 3, 3), 2701 .gpiomux = { 0x60000, 0x60000, 0x20000, 0x20000 }, 2702 .gpiomute = 0, 2703 .tuner_type = TUNER_TCL_MF02GIP_5N, 2704 .tuner_addr = ADDR_UNSET, 2705 .pll = PLL_28, 2706 .has_radio = 1, 2707 .has_remote = 1, 2708 }, 2709 [BTTV_BOARD_VD012] = { 2710 /* D.Heer@Phytec.de */ 2711 .name = "PHYTEC VD-012 (bt878)", 2712 .video_inputs = 4, 2713 /* .audio_inputs= 0, */ 2714 .svhs = NO_SVHS, 2715 .gpiomask = 0x00, 2716 .muxsel = MUXSEL(0, 2, 3, 1), 2717 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */ 2718 .pll = PLL_28, 2719 .tuner_type = TUNER_ABSENT, 2720 .tuner_addr = ADDR_UNSET, 2721 }, 2722 [BTTV_BOARD_VD012_X1] = { 2723 /* D.Heer@Phytec.de */ 2724 .name = "PHYTEC VD-012-X1 (bt878)", 2725 .video_inputs = 4, 2726 /* .audio_inputs= 0, */ 2727 .svhs = 3, 2728 .gpiomask = 0x00, 2729 .muxsel = MUXSEL(2, 3, 1), 2730 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */ 2731 .pll = PLL_28, 2732 .tuner_type = TUNER_ABSENT, 2733 .tuner_addr = ADDR_UNSET, 2734 }, 2735 [BTTV_BOARD_VD012_X2] = { 2736 /* D.Heer@Phytec.de */ 2737 .name = "PHYTEC VD-012-X2 (bt878)", 2738 .video_inputs = 4, 2739 /* .audio_inputs= 0, */ 2740 .svhs = 3, 2741 .gpiomask = 0x00, 2742 .muxsel = MUXSEL(3, 2, 1), 2743 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */ 2744 .pll = PLL_28, 2745 .tuner_type = TUNER_ABSENT, 2746 .tuner_addr = ADDR_UNSET, 2747 }, 2748 [BTTV_BOARD_GEOVISION_GV800S] = { 2749 /* Bruno Christo <bchristo@inf.ufsm.br> 2750 * 2751 * GeoVision GV-800(S) has 4 Conexant Fusion 878A: 2752 * 1 audio input per BT878A = 4 audio inputs 2753 * 4 video inputs per BT878A = 16 video inputs 2754 * This is the first BT878A chip of the GV-800(S). It's the 2755 * "master" chip and it controls the video inputs through an 2756 * analog multiplexer (a CD22M3494) via some GPIO pins. The 2757 * slaves should use card type 0x9e (following this one). 2758 * There is a EEPROM on the card which is currently not handled. 2759 * The audio input is not working yet. 2760 */ 2761 .name = "Geovision GV-800(S) (master)", 2762 .video_inputs = 4, 2763 /* .audio_inputs= 1, */ 2764 .tuner_type = TUNER_ABSENT, 2765 .tuner_addr = ADDR_UNSET, 2766 .svhs = NO_SVHS, 2767 .gpiomask = 0xf107f, 2768 .no_gpioirq = 1, 2769 .muxsel = MUXSEL(2, 2, 2, 2), 2770 .pll = PLL_28, 2771 .no_msp34xx = 1, 2772 .no_tda7432 = 1, 2773 .muxsel_hook = gv800s_muxsel, 2774 }, 2775 [BTTV_BOARD_GEOVISION_GV800S_SL] = { 2776 /* Bruno Christo <bchristo@inf.ufsm.br> 2777 * 2778 * GeoVision GV-800(S) has 4 Conexant Fusion 878A: 2779 * 1 audio input per BT878A = 4 audio inputs 2780 * 4 video inputs per BT878A = 16 video inputs 2781 * The 3 other BT878A chips are "slave" chips of the GV-800(S) 2782 * and should use this card type. 2783 * The audio input is not working yet. 2784 */ 2785 .name = "Geovision GV-800(S) (slave)", 2786 .video_inputs = 4, 2787 /* .audio_inputs= 1, */ 2788 .tuner_type = TUNER_ABSENT, 2789 .tuner_addr = ADDR_UNSET, 2790 .svhs = NO_SVHS, 2791 .gpiomask = 0x00, 2792 .no_gpioirq = 1, 2793 .muxsel = MUXSEL(2, 2, 2, 2), 2794 .pll = PLL_28, 2795 .no_msp34xx = 1, 2796 .no_tda7432 = 1, 2797 .muxsel_hook = gv800s_muxsel, 2798 }, 2799 [BTTV_BOARD_PV183] = { 2800 .name = "ProVideo PV183", /* 0x9f */ 2801 .video_inputs = 2, 2802 /* .audio_inputs= 0, */ 2803 .svhs = NO_SVHS, 2804 .gpiomask = 0, 2805 .muxsel = MUXSEL(2, 3), 2806 .gpiomux = { 0 }, 2807 .no_msp34xx = 1, 2808 .pll = PLL_28, 2809 .tuner_type = TUNER_ABSENT, 2810 .tuner_addr = ADDR_UNSET, 2811 }, 2812 /* ---- card 0xa0---------------------------------- */ 2813 [BTTV_BOARD_TVT_TD3116] = { 2814 .name = "Tongwei Video Technology TD-3116", 2815 .video_inputs = 16, 2816 .gpiomask = 0xc00ff, 2817 .muxsel = MUXSEL(2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2), 2818 .muxsel_hook = td3116_muxsel, 2819 .svhs = NO_SVHS, 2820 .pll = PLL_28, 2821 .tuner_type = TUNER_ABSENT, 2822 }, 2823 [BTTV_BOARD_APOSONIC_WDVR] = { 2824 .name = "Aposonic W-DVR", 2825 .video_inputs = 4, 2826 .svhs = NO_SVHS, 2827 .muxsel = MUXSEL(2, 3, 1, 0), 2828 .tuner_type = TUNER_ABSENT, 2829 }, 2830 [BTTV_BOARD_ADLINK_MPG24] = { 2831 /* Adlink MPG24 */ 2832 .name = "Adlink MPG24", 2833 .video_inputs = 1, 2834 /* .audio_inputs= 1, */ 2835 .svhs = NO_SVHS, 2836 .muxsel = MUXSEL(2, 2, 2, 2), 2837 .tuner_type = UNSET, 2838 .tuner_addr = ADDR_UNSET, 2839 .pll = PLL_28, 2840 }, 2841 [BTTV_BOARD_BT848_CAP_14] = { 2842 .name = "Bt848 Capture 14MHz", 2843 .video_inputs = 4, 2844 .svhs = 2, 2845 .muxsel = MUXSEL(2, 3, 1, 0), 2846 .pll = PLL_14, 2847 .tuner_type = TUNER_ABSENT, 2848 }, 2849 [BTTV_BOARD_CYBERVISION_CV06] = { 2850 .name = "CyberVision CV06 (SV)", 2851 .video_inputs = 4, 2852 /* .audio_inputs= 0, */ 2853 .svhs = NO_SVHS, 2854 .muxsel = MUXSEL(2, 3, 1, 0), 2855 .pll = PLL_28, 2856 .tuner_type = TUNER_ABSENT, 2857 .tuner_addr = ADDR_UNSET, 2858 }, 2859 [BTTV_BOARD_KWORLD_VSTREAM_XPERT] = { 2860 /* Pojar George <geoubuntu@gmail.com> */ 2861 .name = "Kworld V-Stream Xpert TV PVR878", 2862 .video_inputs = 3, 2863 /* .audio_inputs= 1, */ 2864 .svhs = 2, 2865 .gpiomask = 0x001c0007, 2866 .muxsel = MUXSEL(2, 3, 1, 1), 2867 .gpiomux = { 0, 1, 2, 2 }, 2868 .gpiomute = 3, 2869 .pll = PLL_28, 2870 .tuner_type = TUNER_TENA_9533_DI, 2871 .tuner_addr = ADDR_UNSET, 2872 .has_remote = 1, 2873 .has_radio = 1, 2874 }, 2875 /* ---- card 0xa6---------------------------------- */ 2876 [BTTV_BOARD_PCI_8604PW] = { 2877 /* PCI-8604PW with special unlock sequence */ 2878 .name = "PCI-8604PW", 2879 .video_inputs = 2, 2880 /* .audio_inputs= 0, */ 2881 .svhs = NO_SVHS, 2882 /* The second input is available on CN4, if populated. 2883 * The other 5x2 header (CN2?) connects to the same inputs 2884 * as the on-board BNCs */ 2885 .muxsel = MUXSEL(2, 3), 2886 .tuner_type = TUNER_ABSENT, 2887 .no_msp34xx = 1, 2888 .no_tda7432 = 1, 2889 .pll = PLL_35, 2890 }, 2891 }; 2892 2893 static const unsigned int bttv_num_tvcards = ARRAY_SIZE(bttv_tvcards); 2894 2895 /* ----------------------------------------------------------------------- */ 2896 2897 static unsigned char eeprom_data[256]; 2898 2899 /* 2900 * identify card 2901 */ 2902 void bttv_idcard(struct bttv *btv) 2903 { 2904 unsigned int gpiobits; 2905 int i,type; 2906 2907 /* read PCI subsystem ID */ 2908 btv->cardid = btv->c.pci->subsystem_device << 16; 2909 btv->cardid |= btv->c.pci->subsystem_vendor; 2910 2911 if (0 != btv->cardid && 0xffffffff != btv->cardid) { 2912 /* look for the card */ 2913 for (type = -1, i = 0; cards[i].id != 0; i++) 2914 if (cards[i].id == btv->cardid) 2915 type = i; 2916 2917 if (type != -1) { 2918 /* found it */ 2919 pr_info("%d: detected: %s [card=%d], PCI subsystem ID is %04x:%04x\n", 2920 btv->c.nr, cards[type].name, cards[type].cardnr, 2921 btv->cardid & 0xffff, 2922 (btv->cardid >> 16) & 0xffff); 2923 btv->c.type = cards[type].cardnr; 2924 } else { 2925 /* 404 */ 2926 pr_info("%d: subsystem: %04x:%04x (UNKNOWN)\n", 2927 btv->c.nr, btv->cardid & 0xffff, 2928 (btv->cardid >> 16) & 0xffff); 2929 pr_debug("please mail id, board name and the correct card= insmod option to linux-media@vger.kernel.org\n"); 2930 } 2931 } 2932 2933 /* let the user override the autodetected type */ 2934 if (card[btv->c.nr] < bttv_num_tvcards) 2935 btv->c.type=card[btv->c.nr]; 2936 2937 /* print which card config we are using */ 2938 pr_info("%d: using: %s [card=%d,%s]\n", 2939 btv->c.nr, bttv_tvcards[btv->c.type].name, btv->c.type, 2940 card[btv->c.nr] < bttv_num_tvcards 2941 ? "insmod option" : "autodetected"); 2942 2943 /* overwrite gpio stuff ?? */ 2944 if (UNSET == audioall && UNSET == audiomux[0]) 2945 return; 2946 2947 if (UNSET != audiomux[0]) { 2948 gpiobits = 0; 2949 for (i = 0; i < ARRAY_SIZE(bttv_tvcards->gpiomux); i++) { 2950 bttv_tvcards[btv->c.type].gpiomux[i] = audiomux[i]; 2951 gpiobits |= audiomux[i]; 2952 } 2953 } else { 2954 gpiobits = audioall; 2955 for (i = 0; i < ARRAY_SIZE(bttv_tvcards->gpiomux); i++) { 2956 bttv_tvcards[btv->c.type].gpiomux[i] = audioall; 2957 } 2958 } 2959 bttv_tvcards[btv->c.type].gpiomask = (UNSET != gpiomask) ? gpiomask : gpiobits; 2960 pr_info("%d: gpio config override: mask=0x%x, mux=", 2961 btv->c.nr, bttv_tvcards[btv->c.type].gpiomask); 2962 for (i = 0; i < ARRAY_SIZE(bttv_tvcards->gpiomux); i++) { 2963 pr_cont("%s0x%x", 2964 i ? "," : "", bttv_tvcards[btv->c.type].gpiomux[i]); 2965 } 2966 pr_cont("\n"); 2967 } 2968 2969 /* 2970 * (most) board specific initialisations goes here 2971 */ 2972 2973 /* Some Modular Technology cards have an eeprom, but no subsystem ID */ 2974 static void identify_by_eeprom(struct bttv *btv, unsigned char eeprom_data[256]) 2975 { 2976 int type = -1; 2977 2978 if (0 == strncmp(eeprom_data,"GET MM20xPCTV",13)) 2979 type = BTTV_BOARD_MODTEC_205; 2980 else if (0 == strncmp(eeprom_data+20,"Picolo",7)) 2981 type = BTTV_BOARD_EURESYS_PICOLO; 2982 else if (eeprom_data[0] == 0x84 && eeprom_data[2]== 0) 2983 type = BTTV_BOARD_HAUPPAUGE; /* old bt848 */ 2984 2985 if (-1 != type) { 2986 btv->c.type = type; 2987 pr_info("%d: detected by eeprom: %s [card=%d]\n", 2988 btv->c.nr, bttv_tvcards[btv->c.type].name, btv->c.type); 2989 } 2990 } 2991 2992 static void flyvideo_gpio(struct bttv *btv) 2993 { 2994 int gpio, has_remote, has_radio, is_capture_only; 2995 int is_lr90, has_tda9820_tda9821; 2996 int tuner_type = UNSET, ttype; 2997 2998 gpio_inout(0xffffff, 0); 2999 udelay(8); /* without this we would see the 0x1800 mask */ 3000 gpio = gpio_read(); 3001 /* FIXME: must restore OUR_EN ??? */ 3002 3003 /* all cards provide GPIO info, some have an additional eeprom 3004 * LR50: GPIO coding can be found lower right CP1 .. CP9 3005 * CP9=GPIO23 .. CP1=GPIO15; when OPEN, the corresponding GPIO reads 1. 3006 * GPIO14-12: n.c. 3007 * LR90: GP9=GPIO23 .. GP1=GPIO15 (right above the bt878) 3008 3009 * lowest 3 bytes are remote control codes (no handshake needed) 3010 * xxxFFF: No remote control chip soldered 3011 * xxxF00(LR26/LR50), xxxFE0(LR90): Remote control chip (LVA001 or CF45) soldered 3012 * Note: Some bits are Audio_Mask ! 3013 */ 3014 ttype = (gpio & 0x0f0000) >> 16; 3015 switch (ttype) { 3016 case 0x0: 3017 tuner_type = 2; /* NTSC, e.g. TPI8NSR11P */ 3018 break; 3019 case 0x2: 3020 tuner_type = 39; /* LG NTSC (newer TAPC series) TAPC-H701P */ 3021 break; 3022 case 0x4: 3023 tuner_type = 5; /* Philips PAL TPI8PSB02P, TPI8PSB12P, TPI8PSB12D or FI1216, FM1216 */ 3024 break; 3025 case 0x6: 3026 tuner_type = 37; /* LG PAL (newer TAPC series) TAPC-G702P */ 3027 break; 3028 case 0xC: 3029 tuner_type = 3; /* Philips SECAM(+PAL) FQ1216ME or FI1216MF */ 3030 break; 3031 default: 3032 pr_info("%d: FlyVideo_gpio: unknown tuner type\n", btv->c.nr); 3033 break; 3034 } 3035 3036 has_remote = gpio & 0x800000; 3037 has_radio = gpio & 0x400000; 3038 /* unknown 0x200000; 3039 * unknown2 0x100000; */ 3040 is_capture_only = !(gpio & 0x008000); /* GPIO15 */ 3041 has_tda9820_tda9821 = !(gpio & 0x004000); 3042 is_lr90 = !(gpio & 0x002000); /* else LR26/LR50 (LR38/LR51 f. capture only) */ 3043 /* 3044 * gpio & 0x001000 output bit for audio routing */ 3045 3046 if (is_capture_only) 3047 tuner_type = TUNER_ABSENT; /* No tuner present */ 3048 3049 pr_info("%d: FlyVideo Radio=%s RemoteControl=%s Tuner=%d gpio=0x%06x\n", 3050 btv->c.nr, has_radio ? "yes" : "no", 3051 has_remote ? "yes" : "no", tuner_type, gpio); 3052 pr_info("%d: FlyVideo LR90=%s tda9821/tda9820=%s capture_only=%s\n", 3053 btv->c.nr, is_lr90 ? "yes" : "no", 3054 has_tda9820_tda9821 ? "yes" : "no", 3055 is_capture_only ? "yes" : "no"); 3056 3057 if (tuner_type != UNSET) /* only set if known tuner autodetected, else let insmod option through */ 3058 btv->tuner_type = tuner_type; 3059 btv->has_radio = has_radio; 3060 3061 /* LR90 Audio Routing is done by 2 hef4052, so Audio_Mask has 4 bits: 0x001c80 3062 * LR26/LR50 only has 1 hef4052, Audio_Mask 0x000c00 3063 * Audio options: from tuner, from tda9821/tda9821(mono,stereo,sap), from tda9874, ext., mute */ 3064 if (has_tda9820_tda9821) 3065 btv->audio_mode_gpio = lt9415_audio; 3066 /* todo: if(has_tda9874) btv->audio_mode_gpio = fv2000s_audio; */ 3067 } 3068 3069 static int miro_tunermap[] = { 0,6,2,3, 4,5,6,0, 3,0,4,5, 5,2,16,1, 3070 14,2,17,1, 4,1,4,3, 1,2,16,1, 4,4,4,4 }; 3071 static int miro_fmtuner[] = { 0,0,0,0, 0,0,0,0, 0,0,0,0, 0,0,0,1, 3072 1,1,1,1, 1,1,1,0, 0,0,0,0, 0,1,0,0 }; 3073 3074 static void miro_pinnacle_gpio(struct bttv *btv) 3075 { 3076 int id,msp,gpio; 3077 char *info; 3078 3079 gpio_inout(0xffffff, 0); 3080 gpio = gpio_read(); 3081 id = ((gpio>>10) & 63) -1; 3082 msp = bttv_I2CRead(btv, I2C_ADDR_MSP3400, "MSP34xx"); 3083 if (id < 32) { 3084 btv->tuner_type = miro_tunermap[id]; 3085 if (0 == (gpio & 0x20)) { 3086 btv->has_radio = 1; 3087 if (!miro_fmtuner[id]) { 3088 btv->has_matchbox = 1; 3089 btv->mbox_we = (1<<6); 3090 btv->mbox_most = (1<<7); 3091 btv->mbox_clk = (1<<8); 3092 btv->mbox_data = (1<<9); 3093 btv->mbox_mask = (1<<6)|(1<<7)|(1<<8)|(1<<9); 3094 } 3095 } else { 3096 btv->has_radio = 0; 3097 } 3098 if (-1 != msp) { 3099 if (btv->c.type == BTTV_BOARD_MIRO) 3100 btv->c.type = BTTV_BOARD_MIROPRO; 3101 if (btv->c.type == BTTV_BOARD_PINNACLE) 3102 btv->c.type = BTTV_BOARD_PINNACLEPRO; 3103 } 3104 pr_info("%d: miro: id=%d tuner=%d radio=%s stereo=%s\n", 3105 btv->c.nr, id+1, btv->tuner_type, 3106 !btv->has_radio ? "no" : 3107 (btv->has_matchbox ? "matchbox" : "fmtuner"), 3108 (-1 == msp) ? "no" : "yes"); 3109 } else { 3110 /* new cards with microtune tuner */ 3111 id = 63 - id; 3112 btv->has_radio = 0; 3113 switch (id) { 3114 case 1: 3115 info = "PAL / mono"; 3116 btv->tda9887_conf = TDA9887_INTERCARRIER; 3117 break; 3118 case 2: 3119 info = "PAL+SECAM / stereo"; 3120 btv->has_radio = 1; 3121 btv->tda9887_conf = TDA9887_QSS; 3122 break; 3123 case 3: 3124 info = "NTSC / stereo"; 3125 btv->has_radio = 1; 3126 btv->tda9887_conf = TDA9887_QSS; 3127 break; 3128 case 4: 3129 info = "PAL+SECAM / mono"; 3130 btv->tda9887_conf = TDA9887_QSS; 3131 break; 3132 case 5: 3133 info = "NTSC / mono"; 3134 btv->tda9887_conf = TDA9887_INTERCARRIER; 3135 break; 3136 case 6: 3137 info = "NTSC / stereo"; 3138 btv->tda9887_conf = TDA9887_INTERCARRIER; 3139 break; 3140 case 7: 3141 info = "PAL / stereo"; 3142 btv->tda9887_conf = TDA9887_INTERCARRIER; 3143 break; 3144 default: 3145 info = "oops: unknown card"; 3146 break; 3147 } 3148 if (-1 != msp) 3149 btv->c.type = BTTV_BOARD_PINNACLEPRO; 3150 pr_info("%d: pinnacle/mt: id=%d info=\"%s\" radio=%s\n", 3151 btv->c.nr, id, info, btv->has_radio ? "yes" : "no"); 3152 btv->tuner_type = TUNER_MT2032; 3153 } 3154 } 3155 3156 /* GPIO21 L: Buffer aktiv, H: Buffer inaktiv */ 3157 #define LM1882_SYNC_DRIVE 0x200000L 3158 3159 static void init_ids_eagle(struct bttv *btv) 3160 { 3161 gpio_inout(0xffffff,0xFFFF37); 3162 gpio_write(0x200020); 3163 3164 /* flash strobe inverter ?! */ 3165 gpio_write(0x200024); 3166 3167 /* switch sync drive off */ 3168 gpio_bits(LM1882_SYNC_DRIVE,LM1882_SYNC_DRIVE); 3169 3170 /* set BT848 muxel to 2 */ 3171 btaor((2)<<5, ~(2<<5), BT848_IFORM); 3172 } 3173 3174 /* Muxsel helper for the IDS Eagle. 3175 * the eagles does not use the standard muxsel-bits but 3176 * has its own multiplexer */ 3177 static void eagle_muxsel(struct bttv *btv, unsigned int input) 3178 { 3179 gpio_bits(3, input & 3); 3180 3181 /* composite */ 3182 /* set chroma ADC to sleep */ 3183 btor(BT848_ADC_C_SLEEP, BT848_ADC); 3184 /* set to composite video */ 3185 btand(~BT848_CONTROL_COMP, BT848_E_CONTROL); 3186 btand(~BT848_CONTROL_COMP, BT848_O_CONTROL); 3187 3188 /* switch sync drive off */ 3189 gpio_bits(LM1882_SYNC_DRIVE,LM1882_SYNC_DRIVE); 3190 } 3191 3192 static void gvc1100_muxsel(struct bttv *btv, unsigned int input) 3193 { 3194 static const int masks[] = {0x30, 0x01, 0x12, 0x23}; 3195 gpio_write(masks[input%4]); 3196 } 3197 3198 /* LMLBT4x initialization - to allow access to GPIO bits for sensors input and 3199 alarms output 3200 3201 GPIObit | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | 3202 assignment | TI | O3|INx| O2| O1|IN4|IN3|IN2|IN1| | | 3203 3204 IN - sensor inputs, INx - sensor inputs and TI XORed together 3205 O1,O2,O3 - alarm outputs (relays) 3206 3207 OUT ENABLE 1 1 0 . 1 1 0 0 . 0 0 0 0 = 0x6C0 3208 3209 */ 3210 3211 static void init_lmlbt4x(struct bttv *btv) 3212 { 3213 pr_debug("LMLBT4x init\n"); 3214 btwrite(0x000000, BT848_GPIO_REG_INP); 3215 gpio_inout(0xffffff, 0x0006C0); 3216 gpio_write(0x000000); 3217 } 3218 3219 static void sigmaSQ_muxsel(struct bttv *btv, unsigned int input) 3220 { 3221 unsigned int inmux = input % 8; 3222 gpio_inout( 0xf, 0xf ); 3223 gpio_bits( 0xf, inmux ); 3224 } 3225 3226 static void sigmaSLC_muxsel(struct bttv *btv, unsigned int input) 3227 { 3228 unsigned int inmux = input % 4; 3229 gpio_inout( 3<<9, 3<<9 ); 3230 gpio_bits( 3<<9, inmux<<9 ); 3231 } 3232 3233 static void geovision_muxsel(struct bttv *btv, unsigned int input) 3234 { 3235 unsigned int inmux = input % 16; 3236 gpio_inout(0xf, 0xf); 3237 gpio_bits(0xf, inmux); 3238 } 3239 3240 /* 3241 * The TD3116 has 2 74HC4051 muxes wired to the MUX0 input of a bt878. 3242 * The first 74HC4051 has the lower 8 inputs, the second one the higher 8. 3243 * The muxes are controlled via a 74HC373 latch which is connected to 3244 * GPIOs 0-7. GPIO 18 is connected to the LE signal of the latch. 3245 * Q0 of the latch is connected to the Enable (~E) input of the first 3246 * 74HC4051. Q1 - Q3 are connected to S0 - S2 of the same 74HC4051. 3247 * Q4 - Q7 are connected to the second 74HC4051 in the same way. 3248 */ 3249 3250 static void td3116_latch_value(struct bttv *btv, u32 value) 3251 { 3252 gpio_bits((1<<18) | 0xff, value); 3253 gpio_bits((1<<18) | 0xff, (1<<18) | value); 3254 udelay(1); 3255 gpio_bits((1<<18) | 0xff, value); 3256 } 3257 3258 static void td3116_muxsel(struct bttv *btv, unsigned int input) 3259 { 3260 u32 value; 3261 u32 highbit; 3262 3263 highbit = (input & 0x8) >> 3 ; 3264 3265 /* Disable outputs and set value in the mux */ 3266 value = 0x11; /* Disable outputs */ 3267 value |= ((input & 0x7) << 1) << (4 * highbit); 3268 td3116_latch_value(btv, value); 3269 3270 /* Enable the correct output */ 3271 value &= ~0x11; 3272 value |= ((highbit ^ 0x1) << 4) | highbit; 3273 td3116_latch_value(btv, value); 3274 } 3275 3276 /* ----------------------------------------------------------------------- */ 3277 3278 static void bttv_reset_audio(struct bttv *btv) 3279 { 3280 /* 3281 * BT878A has a audio-reset register. 3282 * 1. This register is an audio reset function but it is in 3283 * function-0 (video capture) address space. 3284 * 2. It is enough to do this once per power-up of the card. 3285 * 3. There is a typo in the Conexant doc -- it is not at 3286 * 0x5B, but at 0x058. (B is an odd-number, obviously a typo!). 3287 * --//Shrikumar 030609 3288 */ 3289 if (btv->id != 878) 3290 return; 3291 3292 if (bttv_debug) 3293 pr_debug("%d: BT878A ARESET\n", btv->c.nr); 3294 btwrite((1<<7), 0x058); 3295 udelay(10); 3296 btwrite( 0, 0x058); 3297 } 3298 3299 /* initialization part one -- before registering i2c bus */ 3300 void bttv_init_card1(struct bttv *btv) 3301 { 3302 switch (btv->c.type) { 3303 case BTTV_BOARD_HAUPPAUGE: 3304 case BTTV_BOARD_HAUPPAUGE878: 3305 boot_msp34xx(btv,5); 3306 break; 3307 case BTTV_BOARD_VOODOOTV_200: 3308 case BTTV_BOARD_VOODOOTV_FM: 3309 boot_msp34xx(btv,20); 3310 break; 3311 case BTTV_BOARD_AVERMEDIA98: 3312 boot_msp34xx(btv,11); 3313 break; 3314 case BTTV_BOARD_HAUPPAUGEPVR: 3315 pvr_boot(btv); 3316 break; 3317 case BTTV_BOARD_TWINHAN_DST: 3318 case BTTV_BOARD_AVDVBT_771: 3319 case BTTV_BOARD_PINNACLESAT: 3320 btv->use_i2c_hw = 1; 3321 break; 3322 case BTTV_BOARD_ADLINK_RTV24: 3323 init_RTV24( btv ); 3324 break; 3325 case BTTV_BOARD_PCI_8604PW: 3326 init_PCI8604PW(btv); 3327 break; 3328 3329 } 3330 if (!bttv_tvcards[btv->c.type].has_dvb) 3331 bttv_reset_audio(btv); 3332 } 3333 3334 /* initialization part two -- after registering i2c bus */ 3335 void bttv_init_card2(struct bttv *btv) 3336 { 3337 btv->tuner_type = UNSET; 3338 3339 if (BTTV_BOARD_UNKNOWN == btv->c.type) { 3340 bttv_readee(btv,eeprom_data,0xa0); 3341 identify_by_eeprom(btv,eeprom_data); 3342 } 3343 3344 switch (btv->c.type) { 3345 case BTTV_BOARD_MIRO: 3346 case BTTV_BOARD_MIROPRO: 3347 case BTTV_BOARD_PINNACLE: 3348 case BTTV_BOARD_PINNACLEPRO: 3349 /* miro/pinnacle */ 3350 miro_pinnacle_gpio(btv); 3351 break; 3352 case BTTV_BOARD_FLYVIDEO_98: 3353 case BTTV_BOARD_MAXI: 3354 case BTTV_BOARD_LIFE_FLYKIT: 3355 case BTTV_BOARD_FLYVIDEO: 3356 case BTTV_BOARD_TYPHOON_TVIEW: 3357 case BTTV_BOARD_CHRONOS_VS2: 3358 case BTTV_BOARD_FLYVIDEO_98FM: 3359 case BTTV_BOARD_FLYVIDEO2000: 3360 case BTTV_BOARD_FLYVIDEO98EZ: 3361 case BTTV_BOARD_CONFERENCETV: 3362 case BTTV_BOARD_LIFETEC_9415: 3363 flyvideo_gpio(btv); 3364 break; 3365 case BTTV_BOARD_HAUPPAUGE: 3366 case BTTV_BOARD_HAUPPAUGE878: 3367 case BTTV_BOARD_HAUPPAUGEPVR: 3368 /* pick up some config infos from the eeprom */ 3369 bttv_readee(btv,eeprom_data,0xa0); 3370 hauppauge_eeprom(btv); 3371 break; 3372 case BTTV_BOARD_AVERMEDIA98: 3373 case BTTV_BOARD_AVPHONE98: 3374 bttv_readee(btv,eeprom_data,0xa0); 3375 avermedia_eeprom(btv); 3376 break; 3377 case BTTV_BOARD_PXC200: 3378 init_PXC200(btv); 3379 break; 3380 case BTTV_BOARD_PICOLO_TETRA_CHIP: 3381 picolo_tetra_init(btv); 3382 break; 3383 case BTTV_BOARD_VHX: 3384 btv->has_radio = 1; 3385 btv->has_matchbox = 1; 3386 btv->mbox_we = 0x20; 3387 btv->mbox_most = 0; 3388 btv->mbox_clk = 0x08; 3389 btv->mbox_data = 0x10; 3390 btv->mbox_mask = 0x38; 3391 break; 3392 case BTTV_BOARD_VOBIS_BOOSTAR: 3393 case BTTV_BOARD_TERRATV: 3394 terratec_active_radio_upgrade(btv); 3395 break; 3396 case BTTV_BOARD_MAGICTVIEW061: 3397 if (btv->cardid == 0x3002144f) { 3398 btv->has_radio=1; 3399 pr_info("%d: radio detected by subsystem id (CPH05x)\n", 3400 btv->c.nr); 3401 } 3402 break; 3403 case BTTV_BOARD_STB2: 3404 if (btv->cardid == 0x3060121a) { 3405 /* Fix up entry for 3DFX VoodooTV 100, 3406 which is an OEM STB card variant. */ 3407 btv->has_radio=0; 3408 btv->tuner_type=TUNER_TEMIC_NTSC; 3409 } 3410 break; 3411 case BTTV_BOARD_OSPREY1x0: 3412 case BTTV_BOARD_OSPREY1x0_848: 3413 case BTTV_BOARD_OSPREY101_848: 3414 case BTTV_BOARD_OSPREY1x1: 3415 case BTTV_BOARD_OSPREY1x1_SVID: 3416 case BTTV_BOARD_OSPREY2xx: 3417 case BTTV_BOARD_OSPREY2x0_SVID: 3418 case BTTV_BOARD_OSPREY2x0: 3419 case BTTV_BOARD_OSPREY440: 3420 case BTTV_BOARD_OSPREY500: 3421 case BTTV_BOARD_OSPREY540: 3422 case BTTV_BOARD_OSPREY2000: 3423 bttv_readee(btv,eeprom_data,0xa0); 3424 osprey_eeprom(btv, eeprom_data); 3425 break; 3426 case BTTV_BOARD_IDS_EAGLE: 3427 init_ids_eagle(btv); 3428 break; 3429 case BTTV_BOARD_MODTEC_205: 3430 bttv_readee(btv,eeprom_data,0xa0); 3431 modtec_eeprom(btv); 3432 break; 3433 case BTTV_BOARD_LMLBT4: 3434 init_lmlbt4x(btv); 3435 break; 3436 case BTTV_BOARD_TIBET_CS16: 3437 tibetCS16_init(btv); 3438 break; 3439 case BTTV_BOARD_KODICOM_4400R: 3440 kodicom4400r_init(btv); 3441 break; 3442 case BTTV_BOARD_GEOVISION_GV800S: 3443 gv800s_init(btv); 3444 break; 3445 } 3446 3447 /* pll configuration */ 3448 if (!(btv->id==848 && btv->revision==0x11)) { 3449 /* defaults from card list */ 3450 if (PLL_28 == bttv_tvcards[btv->c.type].pll) { 3451 btv->pll.pll_ifreq=28636363; 3452 btv->pll.pll_crystal=BT848_IFORM_XT0; 3453 } 3454 if (PLL_35 == bttv_tvcards[btv->c.type].pll) { 3455 btv->pll.pll_ifreq=35468950; 3456 btv->pll.pll_crystal=BT848_IFORM_XT1; 3457 } 3458 if (PLL_14 == bttv_tvcards[btv->c.type].pll) { 3459 btv->pll.pll_ifreq = 14318181; 3460 btv->pll.pll_crystal = BT848_IFORM_XT0; 3461 } 3462 /* insmod options can override */ 3463 switch (pll[btv->c.nr]) { 3464 case 0: /* none */ 3465 btv->pll.pll_crystal = 0; 3466 btv->pll.pll_ifreq = 0; 3467 btv->pll.pll_ofreq = 0; 3468 break; 3469 case 1: /* 28 MHz */ 3470 case 28: 3471 btv->pll.pll_ifreq = 28636363; 3472 btv->pll.pll_ofreq = 0; 3473 btv->pll.pll_crystal = BT848_IFORM_XT0; 3474 break; 3475 case 2: /* 35 MHz */ 3476 case 35: 3477 btv->pll.pll_ifreq = 35468950; 3478 btv->pll.pll_ofreq = 0; 3479 btv->pll.pll_crystal = BT848_IFORM_XT1; 3480 break; 3481 case 3: /* 14 MHz */ 3482 case 14: 3483 btv->pll.pll_ifreq = 14318181; 3484 btv->pll.pll_ofreq = 0; 3485 btv->pll.pll_crystal = BT848_IFORM_XT0; 3486 break; 3487 } 3488 } 3489 btv->pll.pll_current = -1; 3490 3491 /* tuner configuration (from card list / autodetect / insmod option) */ 3492 if (UNSET != bttv_tvcards[btv->c.type].tuner_type) 3493 if (UNSET == btv->tuner_type) 3494 btv->tuner_type = bttv_tvcards[btv->c.type].tuner_type; 3495 if (UNSET != tuner[btv->c.nr]) 3496 btv->tuner_type = tuner[btv->c.nr]; 3497 3498 if (btv->tuner_type == TUNER_ABSENT) 3499 pr_info("%d: tuner absent\n", btv->c.nr); 3500 else if (btv->tuner_type == UNSET) 3501 pr_warn("%d: tuner type unset\n", btv->c.nr); 3502 else 3503 pr_info("%d: tuner type=%d\n", btv->c.nr, btv->tuner_type); 3504 3505 if (autoload != UNSET) { 3506 pr_warn("%d: the autoload option is obsolete\n", btv->c.nr); 3507 pr_warn("%d: use option msp3400, tda7432 or tvaudio to override which audio module should be used\n", 3508 btv->c.nr); 3509 } 3510 3511 if (UNSET == btv->tuner_type) 3512 btv->tuner_type = TUNER_ABSENT; 3513 3514 btv->dig = bttv_tvcards[btv->c.type].has_dig_in ? 3515 bttv_tvcards[btv->c.type].video_inputs - 1 : UNSET; 3516 btv->svhs = bttv_tvcards[btv->c.type].svhs == NO_SVHS ? 3517 UNSET : bttv_tvcards[btv->c.type].svhs; 3518 if (svhs[btv->c.nr] != UNSET) 3519 btv->svhs = svhs[btv->c.nr]; 3520 if (remote[btv->c.nr] != UNSET) 3521 btv->has_remote = remote[btv->c.nr]; 3522 3523 if (bttv_tvcards[btv->c.type].has_radio) 3524 btv->has_radio = 1; 3525 if (bttv_tvcards[btv->c.type].has_remote) 3526 btv->has_remote = 1; 3527 if (!bttv_tvcards[btv->c.type].no_gpioirq) 3528 btv->gpioirq = 1; 3529 if (bttv_tvcards[btv->c.type].volume_gpio) 3530 btv->volume_gpio = bttv_tvcards[btv->c.type].volume_gpio; 3531 if (bttv_tvcards[btv->c.type].audio_mode_gpio) 3532 btv->audio_mode_gpio = bttv_tvcards[btv->c.type].audio_mode_gpio; 3533 3534 if (btv->tuner_type == TUNER_ABSENT) 3535 return; /* no tuner or related drivers to load */ 3536 3537 if (btv->has_saa6588 || saa6588[btv->c.nr]) { 3538 /* Probe for RDS receiver chip */ 3539 static const unsigned short addrs[] = { 3540 0x20 >> 1, 3541 0x22 >> 1, 3542 I2C_CLIENT_END 3543 }; 3544 struct v4l2_subdev *sd; 3545 3546 sd = v4l2_i2c_new_subdev(&btv->c.v4l2_dev, 3547 &btv->c.i2c_adap, "saa6588", 0, addrs); 3548 btv->has_saa6588 = (sd != NULL); 3549 } 3550 3551 /* try to detect audio/fader chips */ 3552 3553 /* First check if the user specified the audio chip via a module 3554 option. */ 3555 3556 switch (audiodev[btv->c.nr]) { 3557 case -1: 3558 return; /* do not load any audio module */ 3559 3560 case 0: /* autodetect */ 3561 break; 3562 3563 case 1: { 3564 /* The user specified that we should probe for msp3400 */ 3565 static const unsigned short addrs[] = { 3566 I2C_ADDR_MSP3400 >> 1, 3567 I2C_ADDR_MSP3400_ALT >> 1, 3568 I2C_CLIENT_END 3569 }; 3570 3571 btv->sd_msp34xx = v4l2_i2c_new_subdev(&btv->c.v4l2_dev, 3572 &btv->c.i2c_adap, "msp3400", 0, addrs); 3573 if (btv->sd_msp34xx) 3574 return; 3575 goto no_audio; 3576 } 3577 3578 case 2: { 3579 /* The user specified that we should probe for tda7432 */ 3580 static const unsigned short addrs[] = { 3581 I2C_ADDR_TDA7432 >> 1, 3582 I2C_CLIENT_END 3583 }; 3584 3585 if (v4l2_i2c_new_subdev(&btv->c.v4l2_dev, 3586 &btv->c.i2c_adap, "tda7432", 0, addrs)) 3587 return; 3588 goto no_audio; 3589 } 3590 3591 case 3: { 3592 /* The user specified that we should probe for tvaudio */ 3593 btv->sd_tvaudio = v4l2_i2c_new_subdev(&btv->c.v4l2_dev, 3594 &btv->c.i2c_adap, "tvaudio", 0, tvaudio_addrs()); 3595 if (btv->sd_tvaudio) 3596 return; 3597 goto no_audio; 3598 } 3599 3600 default: 3601 pr_warn("%d: unknown audiodev value!\n", btv->c.nr); 3602 return; 3603 } 3604 3605 /* There were no overrides, so now we try to discover this through the 3606 card definition */ 3607 3608 /* probe for msp3400 first: this driver can detect whether or not 3609 it really is a msp3400, so it will return NULL when the device 3610 found is really something else (e.g. a tea6300). */ 3611 if (!bttv_tvcards[btv->c.type].no_msp34xx) { 3612 btv->sd_msp34xx = v4l2_i2c_new_subdev(&btv->c.v4l2_dev, 3613 &btv->c.i2c_adap, "msp3400", 3614 0, I2C_ADDRS(I2C_ADDR_MSP3400 >> 1)); 3615 } else if (bttv_tvcards[btv->c.type].msp34xx_alt) { 3616 btv->sd_msp34xx = v4l2_i2c_new_subdev(&btv->c.v4l2_dev, 3617 &btv->c.i2c_adap, "msp3400", 3618 0, I2C_ADDRS(I2C_ADDR_MSP3400_ALT >> 1)); 3619 } 3620 3621 /* If we found a msp34xx, then we're done. */ 3622 if (btv->sd_msp34xx) 3623 return; 3624 3625 /* Now see if we can find one of the tvaudio devices. */ 3626 btv->sd_tvaudio = v4l2_i2c_new_subdev(&btv->c.v4l2_dev, 3627 &btv->c.i2c_adap, "tvaudio", 0, tvaudio_addrs()); 3628 if (btv->sd_tvaudio) { 3629 /* There may be two tvaudio chips on the card, so try to 3630 find another. */ 3631 v4l2_i2c_new_subdev(&btv->c.v4l2_dev, 3632 &btv->c.i2c_adap, "tvaudio", 0, tvaudio_addrs()); 3633 } 3634 3635 /* it might also be a tda7432. */ 3636 if (!bttv_tvcards[btv->c.type].no_tda7432) { 3637 static const unsigned short addrs[] = { 3638 I2C_ADDR_TDA7432 >> 1, 3639 I2C_CLIENT_END 3640 }; 3641 3642 btv->sd_tda7432 = v4l2_i2c_new_subdev(&btv->c.v4l2_dev, 3643 &btv->c.i2c_adap, "tda7432", 0, addrs); 3644 if (btv->sd_tda7432) 3645 return; 3646 } 3647 if (btv->sd_tvaudio) 3648 return; 3649 3650 no_audio: 3651 pr_warn("%d: audio absent, no audio device found!\n", btv->c.nr); 3652 } 3653 3654 3655 /* initialize the tuner */ 3656 void bttv_init_tuner(struct bttv *btv) 3657 { 3658 int addr = ADDR_UNSET; 3659 3660 if (ADDR_UNSET != bttv_tvcards[btv->c.type].tuner_addr) 3661 addr = bttv_tvcards[btv->c.type].tuner_addr; 3662 3663 if (btv->tuner_type != TUNER_ABSENT) { 3664 struct tuner_setup tun_setup; 3665 3666 /* Load tuner module before issuing tuner config call! */ 3667 if (btv->has_radio) 3668 v4l2_i2c_new_subdev(&btv->c.v4l2_dev, 3669 &btv->c.i2c_adap, "tuner", 3670 0, v4l2_i2c_tuner_addrs(ADDRS_RADIO)); 3671 v4l2_i2c_new_subdev(&btv->c.v4l2_dev, 3672 &btv->c.i2c_adap, "tuner", 3673 0, v4l2_i2c_tuner_addrs(ADDRS_DEMOD)); 3674 v4l2_i2c_new_subdev(&btv->c.v4l2_dev, 3675 &btv->c.i2c_adap, "tuner", 3676 0, v4l2_i2c_tuner_addrs(ADDRS_TV_WITH_DEMOD)); 3677 3678 tun_setup.mode_mask = T_ANALOG_TV; 3679 tun_setup.type = btv->tuner_type; 3680 tun_setup.addr = addr; 3681 3682 if (btv->has_radio) 3683 tun_setup.mode_mask |= T_RADIO; 3684 3685 bttv_call_all(btv, tuner, s_type_addr, &tun_setup); 3686 } 3687 3688 if (btv->tda9887_conf) { 3689 struct v4l2_priv_tun_config tda9887_cfg; 3690 3691 tda9887_cfg.tuner = TUNER_TDA9887; 3692 tda9887_cfg.priv = &btv->tda9887_conf; 3693 3694 bttv_call_all(btv, tuner, s_config, &tda9887_cfg); 3695 } 3696 } 3697 3698 /* ----------------------------------------------------------------------- */ 3699 3700 static void modtec_eeprom(struct bttv *btv) 3701 { 3702 if( strncmp(&(eeprom_data[0x1e]),"Temic 4066 FY5",14) ==0) { 3703 btv->tuner_type=TUNER_TEMIC_4066FY5_PAL_I; 3704 pr_info("%d: Modtec: Tuner autodetected by eeprom: %s\n", 3705 btv->c.nr, &eeprom_data[0x1e]); 3706 } else if (strncmp(&(eeprom_data[0x1e]),"Alps TSBB5",10) ==0) { 3707 btv->tuner_type=TUNER_ALPS_TSBB5_PAL_I; 3708 pr_info("%d: Modtec: Tuner autodetected by eeprom: %s\n", 3709 btv->c.nr, &eeprom_data[0x1e]); 3710 } else if (strncmp(&(eeprom_data[0x1e]),"Philips FM1246",14) ==0) { 3711 btv->tuner_type=TUNER_PHILIPS_NTSC; 3712 pr_info("%d: Modtec: Tuner autodetected by eeprom: %s\n", 3713 btv->c.nr, &eeprom_data[0x1e]); 3714 } else { 3715 pr_info("%d: Modtec: Unknown TunerString: %s\n", 3716 btv->c.nr, &eeprom_data[0x1e]); 3717 } 3718 } 3719 3720 static void hauppauge_eeprom(struct bttv *btv) 3721 { 3722 struct tveeprom tv; 3723 3724 tveeprom_hauppauge_analog(&btv->i2c_client, &tv, eeprom_data); 3725 btv->tuner_type = tv.tuner_type; 3726 btv->has_radio = tv.has_radio; 3727 3728 pr_info("%d: Hauppauge eeprom indicates model#%d\n", 3729 btv->c.nr, tv.model); 3730 3731 /* 3732 * Some of the 878 boards have duplicate PCI IDs. Switch the board 3733 * type based on model #. 3734 */ 3735 if(tv.model == 64900) { 3736 pr_info("%d: Switching board type from %s to %s\n", 3737 btv->c.nr, 3738 bttv_tvcards[btv->c.type].name, 3739 bttv_tvcards[BTTV_BOARD_HAUPPAUGE_IMPACTVCB].name); 3740 btv->c.type = BTTV_BOARD_HAUPPAUGE_IMPACTVCB; 3741 } 3742 3743 /* The 61334 needs the msp3410 to do the radio demod to get sound */ 3744 if (tv.model == 61334) 3745 btv->radio_uses_msp_demodulator = 1; 3746 } 3747 3748 static int terratec_active_radio_upgrade(struct bttv *btv) 3749 { 3750 int freq; 3751 3752 btv->has_radio = 1; 3753 btv->has_matchbox = 1; 3754 btv->mbox_we = 0x10; 3755 btv->mbox_most = 0x20; 3756 btv->mbox_clk = 0x08; 3757 btv->mbox_data = 0x04; 3758 btv->mbox_mask = 0x3c; 3759 3760 btv->mbox_iow = 1 << 8; 3761 btv->mbox_ior = 1 << 9; 3762 btv->mbox_csel = 1 << 10; 3763 3764 freq=88000/62.5; 3765 tea5757_write(btv, 5 * freq + 0x358); /* write 0x1ed8 */ 3766 if (0x1ed8 == tea5757_read(btv)) { 3767 pr_info("%d: Terratec Active Radio Upgrade found\n", btv->c.nr); 3768 btv->has_radio = 1; 3769 btv->has_saa6588 = 1; 3770 btv->has_matchbox = 1; 3771 } else { 3772 btv->has_radio = 0; 3773 btv->has_matchbox = 0; 3774 } 3775 return 0; 3776 } 3777 3778 3779 /* ----------------------------------------------------------------------- */ 3780 3781 /* 3782 * minimal bootstrap for the WinTV/PVR -- upload altera firmware. 3783 * 3784 * The hcwamc.rbf firmware file is on the Hauppauge driver CD. Have 3785 * a look at Pvr/pvr45xxx.EXE (self-extracting zip archive, can be 3786 * unpacked with unzip). 3787 */ 3788 #define PVR_GPIO_DELAY 10 3789 3790 #define BTTV_ALT_DATA 0x000001 3791 #define BTTV_ALT_DCLK 0x100000 3792 #define BTTV_ALT_NCONFIG 0x800000 3793 3794 static int pvr_altera_load(struct bttv *btv, const u8 *micro, u32 microlen) 3795 { 3796 u32 n; 3797 u8 bits; 3798 int i; 3799 3800 gpio_inout(0xffffff,BTTV_ALT_DATA|BTTV_ALT_DCLK|BTTV_ALT_NCONFIG); 3801 gpio_write(0); 3802 udelay(PVR_GPIO_DELAY); 3803 3804 gpio_write(BTTV_ALT_NCONFIG); 3805 udelay(PVR_GPIO_DELAY); 3806 3807 for (n = 0; n < microlen; n++) { 3808 bits = micro[n]; 3809 for (i = 0 ; i < 8 ; i++) { 3810 gpio_bits(BTTV_ALT_DCLK,0); 3811 if (bits & 0x01) 3812 gpio_bits(BTTV_ALT_DATA,BTTV_ALT_DATA); 3813 else 3814 gpio_bits(BTTV_ALT_DATA,0); 3815 gpio_bits(BTTV_ALT_DCLK,BTTV_ALT_DCLK); 3816 bits >>= 1; 3817 } 3818 } 3819 gpio_bits(BTTV_ALT_DCLK,0); 3820 udelay(PVR_GPIO_DELAY); 3821 3822 /* begin Altera init loop (Not necessary,but doesn't hurt) */ 3823 for (i = 0 ; i < 30 ; i++) { 3824 gpio_bits(BTTV_ALT_DCLK,0); 3825 gpio_bits(BTTV_ALT_DCLK,BTTV_ALT_DCLK); 3826 } 3827 gpio_bits(BTTV_ALT_DCLK,0); 3828 return 0; 3829 } 3830 3831 static int pvr_boot(struct bttv *btv) 3832 { 3833 const struct firmware *fw_entry; 3834 int rc; 3835 3836 rc = request_firmware(&fw_entry, "hcwamc.rbf", &btv->c.pci->dev); 3837 if (rc != 0) { 3838 pr_warn("%d: no altera firmware [via hotplug]\n", btv->c.nr); 3839 return rc; 3840 } 3841 rc = pvr_altera_load(btv, fw_entry->data, fw_entry->size); 3842 pr_info("%d: altera firmware upload %s\n", 3843 btv->c.nr, (rc < 0) ? "failed" : "ok"); 3844 release_firmware(fw_entry); 3845 return rc; 3846 } 3847 3848 /* ----------------------------------------------------------------------- */ 3849 /* some osprey specific stuff */ 3850 3851 static void osprey_eeprom(struct bttv *btv, const u8 ee[256]) 3852 { 3853 int i; 3854 u32 serial = 0; 3855 int cardid = -1; 3856 3857 /* This code will nevery actually get called in this case.... */ 3858 if (btv->c.type == BTTV_BOARD_UNKNOWN) { 3859 /* this might be an antique... check for MMAC label in eeprom */ 3860 if (!strncmp(ee, "MMAC", 4)) { 3861 u8 checksum = 0; 3862 for (i = 0; i < 21; i++) 3863 checksum += ee[i]; 3864 if (checksum != ee[21]) 3865 return; 3866 cardid = BTTV_BOARD_OSPREY1x0_848; 3867 for (i = 12; i < 21; i++) 3868 serial *= 10, serial += ee[i] - '0'; 3869 } 3870 } else { 3871 unsigned short type; 3872 3873 for (i = 4 * 16; i < 8 * 16; i += 16) { 3874 u16 checksum = (__force u16)ip_compute_csum(ee + i, 16); 3875 3876 if ((checksum & 0xff) + (checksum >> 8) == 0xff) 3877 break; 3878 } 3879 if (i >= 8*16) 3880 return; 3881 ee += i; 3882 3883 /* found a valid descriptor */ 3884 type = get_unaligned_be16((__be16 *)(ee+4)); 3885 3886 switch(type) { 3887 /* 848 based */ 3888 case 0x0004: 3889 cardid = BTTV_BOARD_OSPREY1x0_848; 3890 break; 3891 case 0x0005: 3892 cardid = BTTV_BOARD_OSPREY101_848; 3893 break; 3894 3895 /* 878 based */ 3896 case 0x0012: 3897 case 0x0013: 3898 cardid = BTTV_BOARD_OSPREY1x0; 3899 break; 3900 case 0x0014: 3901 case 0x0015: 3902 cardid = BTTV_BOARD_OSPREY1x1; 3903 break; 3904 case 0x0016: 3905 case 0x0017: 3906 case 0x0020: 3907 cardid = BTTV_BOARD_OSPREY1x1_SVID; 3908 break; 3909 case 0x0018: 3910 case 0x0019: 3911 case 0x001E: 3912 case 0x001F: 3913 cardid = BTTV_BOARD_OSPREY2xx; 3914 break; 3915 case 0x001A: 3916 case 0x001B: 3917 cardid = BTTV_BOARD_OSPREY2x0_SVID; 3918 break; 3919 case 0x0040: 3920 cardid = BTTV_BOARD_OSPREY500; 3921 break; 3922 case 0x0050: 3923 case 0x0056: 3924 cardid = BTTV_BOARD_OSPREY540; 3925 /* bttv_osprey_540_init(btv); */ 3926 break; 3927 case 0x0060: 3928 case 0x0070: 3929 case 0x00A0: 3930 cardid = BTTV_BOARD_OSPREY2x0; 3931 /* enable output on select control lines */ 3932 gpio_inout(0xffffff,0x000303); 3933 break; 3934 case 0x00D8: 3935 cardid = BTTV_BOARD_OSPREY440; 3936 break; 3937 default: 3938 /* unknown...leave generic, but get serial # */ 3939 pr_info("%d: osprey eeprom: unknown card type 0x%04x\n", 3940 btv->c.nr, type); 3941 break; 3942 } 3943 serial = get_unaligned_be32((__be32 *)(ee+6)); 3944 } 3945 3946 pr_info("%d: osprey eeprom: card=%d '%s' serial=%u\n", 3947 btv->c.nr, cardid, 3948 cardid > 0 ? bttv_tvcards[cardid].name : "Unknown", serial); 3949 3950 if (cardid<0 || btv->c.type == cardid) 3951 return; 3952 3953 /* card type isn't set correctly */ 3954 if (card[btv->c.nr] < bttv_num_tvcards) { 3955 pr_warn("%d: osprey eeprom: Not overriding user specified card type\n", 3956 btv->c.nr); 3957 } else { 3958 pr_info("%d: osprey eeprom: Changing card type from %d to %d\n", 3959 btv->c.nr, btv->c.type, cardid); 3960 btv->c.type = cardid; 3961 } 3962 } 3963 3964 /* ----------------------------------------------------------------------- */ 3965 /* AVermedia specific stuff, from bktr_card.c */ 3966 3967 static int tuner_0_table[] = { 3968 TUNER_PHILIPS_NTSC, TUNER_PHILIPS_PAL /* PAL-BG*/, 3969 TUNER_PHILIPS_PAL, TUNER_PHILIPS_PAL /* PAL-I*/, 3970 TUNER_PHILIPS_PAL, TUNER_PHILIPS_PAL, 3971 TUNER_PHILIPS_SECAM, TUNER_PHILIPS_SECAM, 3972 TUNER_PHILIPS_SECAM, TUNER_PHILIPS_PAL, 3973 TUNER_PHILIPS_FM1216ME_MK3 }; 3974 3975 static int tuner_1_table[] = { 3976 TUNER_TEMIC_NTSC, TUNER_TEMIC_PAL, 3977 TUNER_TEMIC_PAL, TUNER_TEMIC_PAL, 3978 TUNER_TEMIC_PAL, TUNER_TEMIC_PAL, 3979 TUNER_TEMIC_4012FY5, TUNER_TEMIC_4012FY5, /* TUNER_TEMIC_SECAM */ 3980 TUNER_TEMIC_4012FY5, TUNER_TEMIC_PAL}; 3981 3982 static void avermedia_eeprom(struct bttv *btv) 3983 { 3984 int tuner_make, tuner_tv_fm, tuner_format, tuner_type = 0; 3985 3986 tuner_make = (eeprom_data[0x41] & 0x7); 3987 tuner_tv_fm = (eeprom_data[0x41] & 0x18) >> 3; 3988 tuner_format = (eeprom_data[0x42] & 0xf0) >> 4; 3989 btv->has_remote = (eeprom_data[0x42] & 0x01); 3990 3991 if (tuner_make == 0 || tuner_make == 2) 3992 if (tuner_format <= 0x0a) 3993 tuner_type = tuner_0_table[tuner_format]; 3994 if (tuner_make == 1) 3995 if (tuner_format <= 9) 3996 tuner_type = tuner_1_table[tuner_format]; 3997 3998 if (tuner_make == 4) 3999 if (tuner_format == 0x09) 4000 tuner_type = TUNER_LG_NTSC_NEW_TAPC; /* TAPC-G702P */ 4001 4002 pr_info("%d: Avermedia eeprom[0x%02x%02x]: tuner=", 4003 btv->c.nr, eeprom_data[0x41], eeprom_data[0x42]); 4004 if (tuner_type) { 4005 btv->tuner_type = tuner_type; 4006 pr_cont("%d", tuner_type); 4007 } else 4008 pr_cont("Unknown type"); 4009 pr_cont(" radio:%s remote control:%s\n", 4010 tuner_tv_fm ? "yes" : "no", 4011 btv->has_remote ? "yes" : "no"); 4012 } 4013 4014 /* 4015 * For Voodoo TV/FM and Voodoo 200. These cards' tuners use a TDA9880 4016 * analog demod, which is not I2C controlled like the newer and more common 4017 * TDA9887 series. Instead is has two tri-state input pins, S0 and S1, 4018 * that control the IF for the video and audio. Apparently, bttv GPIO 4019 * 0x10000 is connected to S0. S0 low selects a 38.9 MHz VIF for B/G/D/K/I 4020 * (i.e., PAL) while high selects 45.75 MHz for M/N (i.e., NTSC). 4021 */ 4022 u32 bttv_tda9880_setnorm(struct bttv *btv, u32 gpiobits) 4023 { 4024 4025 if (btv->audio_input == TVAUDIO_INPUT_TUNER) { 4026 if (bttv_tvnorms[btv->tvnorm].v4l2_id & V4L2_STD_MN) 4027 gpiobits |= 0x10000; 4028 else 4029 gpiobits &= ~0x10000; 4030 } 4031 4032 gpio_bits(bttv_tvcards[btv->c.type].gpiomask, gpiobits); 4033 return gpiobits; 4034 } 4035 4036 4037 /* 4038 * reset/enable the MSP on some Hauppauge cards 4039 * Thanks to Kyösti Mälkki (kmalkki@cc.hut.fi)! 4040 * 4041 * Hauppauge: pin 5 4042 * Voodoo: pin 20 4043 */ 4044 static void boot_msp34xx(struct bttv *btv, int pin) 4045 { 4046 int mask = (1 << pin); 4047 4048 gpio_inout(mask,mask); 4049 gpio_bits(mask,0); 4050 mdelay(2); 4051 udelay(500); 4052 gpio_bits(mask,mask); 4053 4054 if (bttv_gpio) 4055 bttv_gpio_tracking(btv,"msp34xx"); 4056 if (bttv_verbose) 4057 pr_info("%d: Hauppauge/Voodoo msp34xx: reset line init [%d]\n", 4058 btv->c.nr, pin); 4059 } 4060 4061 /* ----------------------------------------------------------------------- */ 4062 /* Imagenation L-Model PXC200 Framegrabber */ 4063 /* This is basically the same procedure as 4064 * used by Alessandro Rubini in his pxc200 4065 * driver, but using BTTV functions */ 4066 4067 static void init_PXC200(struct bttv *btv) 4068 { 4069 static int vals[] = { 0x08, 0x09, 0x0a, 0x0b, 0x0d, 0x0d, 0x01, 0x02, 4070 0x03, 0x04, 0x05, 0x06, 0x00 }; 4071 unsigned int i; 4072 int tmp; 4073 u32 val; 4074 4075 /* Initialise GPIO-connevted stuff */ 4076 gpio_inout(0xffffff, (1<<13)); 4077 gpio_write(0); 4078 udelay(3); 4079 gpio_write(1<<13); 4080 /* GPIO inputs are pulled up, so no need to drive 4081 * reset pin any longer */ 4082 gpio_bits(0xffffff, 0); 4083 if (bttv_gpio) 4084 bttv_gpio_tracking(btv,"pxc200"); 4085 4086 /* we could/should try and reset/control the AD pots? but 4087 right now we simply turned off the crushing. Without 4088 this the AGC drifts drifts 4089 remember the EN is reverse logic --> 4090 setting BT848_ADC_AGC_EN disable the AGC 4091 tboult@eecs.lehigh.edu 4092 */ 4093 4094 btwrite(BT848_ADC_RESERVED|BT848_ADC_AGC_EN, BT848_ADC); 4095 4096 /* Initialise MAX517 DAC */ 4097 pr_info("Setting DAC reference voltage level ...\n"); 4098 bttv_I2CWrite(btv,0x5E,0,0x80,1); 4099 4100 /* Initialise 12C508 PIC */ 4101 /* The I2CWrite and I2CRead commmands are actually to the 4102 * same chips - but the R/W bit is included in the address 4103 * argument so the numbers are different */ 4104 4105 4106 pr_info("Initialising 12C508 PIC chip ...\n"); 4107 4108 /* First of all, enable the clock line. This is used in the PXC200-F */ 4109 val = btread(BT848_GPIO_DMA_CTL); 4110 val |= BT848_GPIO_DMA_CTL_GPCLKMODE; 4111 btwrite(val, BT848_GPIO_DMA_CTL); 4112 4113 /* Then, push to 0 the reset pin long enough to reset the * 4114 * device same as above for the reset line, but not the same 4115 * value sent to the GPIO-connected stuff 4116 * which one is the good one? */ 4117 gpio_inout(0xffffff,(1<<2)); 4118 gpio_write(0); 4119 udelay(10); 4120 gpio_write(1<<2); 4121 4122 for (i = 0; i < ARRAY_SIZE(vals); i++) { 4123 tmp=bttv_I2CWrite(btv,0x1E,0,vals[i],1); 4124 if (tmp != -1) { 4125 pr_info("I2C Write(%2.2x) = %i\nI2C Read () = %2.2x\n\n", 4126 vals[i],tmp,bttv_I2CRead(btv,0x1F,NULL)); 4127 } 4128 } 4129 4130 pr_info("PXC200 Initialised\n"); 4131 } 4132 4133 4134 4135 /* ----------------------------------------------------------------------- */ 4136 /* 4137 * The Adlink RTV-24 (aka Angelo) has some special initialisation to unlock 4138 * it. This apparently involves the following procedure for each 878 chip: 4139 * 4140 * 1) write 0x00C3FEFF to the GPIO_OUT_EN register 4141 * 4142 * 2) write to GPIO_DATA 4143 * - 0x0E 4144 * - sleep 1ms 4145 * - 0x10 + 0x0E 4146 * - sleep 10ms 4147 * - 0x0E 4148 * read from GPIO_DATA into buf (uint_32) 4149 * - if ( data>>18 & 0x01 != 0) || ( buf>>19 & 0x01 != 1 ) 4150 * error. ERROR_CPLD_Check_Failed stop. 4151 * 4152 * 3) write to GPIO_DATA 4153 * - write 0x4400 + 0x0E 4154 * - sleep 10ms 4155 * - write 0x4410 + 0x0E 4156 * - sleep 1ms 4157 * - write 0x0E 4158 * read from GPIO_DATA into buf (uint_32) 4159 * - if ( buf>>18 & 0x01 ) || ( buf>>19 & 0x01 != 0 ) 4160 * error. ERROR_CPLD_Check_Failed. 4161 */ 4162 /* ----------------------------------------------------------------------- */ 4163 static void 4164 init_RTV24 (struct bttv *btv) 4165 { 4166 uint32_t dataRead = 0; 4167 long watchdog_value = 0x0E; 4168 4169 pr_info("%d: Adlink RTV-24 initialisation in progress ...\n", 4170 btv->c.nr); 4171 4172 btwrite (0x00c3feff, BT848_GPIO_OUT_EN); 4173 4174 btwrite (0 + watchdog_value, BT848_GPIO_DATA); 4175 msleep (1); 4176 btwrite (0x10 + watchdog_value, BT848_GPIO_DATA); 4177 msleep (10); 4178 btwrite (0 + watchdog_value, BT848_GPIO_DATA); 4179 4180 dataRead = btread (BT848_GPIO_DATA); 4181 4182 if ((((dataRead >> 18) & 0x01) != 0) || (((dataRead >> 19) & 0x01) != 1)) { 4183 pr_info("%d: Adlink RTV-24 initialisation(1) ERROR_CPLD_Check_Failed (read %d)\n", 4184 btv->c.nr, dataRead); 4185 } 4186 4187 btwrite (0x4400 + watchdog_value, BT848_GPIO_DATA); 4188 msleep (10); 4189 btwrite (0x4410 + watchdog_value, BT848_GPIO_DATA); 4190 msleep (1); 4191 btwrite (watchdog_value, BT848_GPIO_DATA); 4192 msleep (1); 4193 dataRead = btread (BT848_GPIO_DATA); 4194 4195 if ((((dataRead >> 18) & 0x01) != 0) || (((dataRead >> 19) & 0x01) != 0)) { 4196 pr_info("%d: Adlink RTV-24 initialisation(2) ERROR_CPLD_Check_Failed (read %d)\n", 4197 btv->c.nr, dataRead); 4198 4199 return; 4200 } 4201 4202 pr_info("%d: Adlink RTV-24 initialisation complete\n", btv->c.nr); 4203 } 4204 4205 4206 4207 /* ----------------------------------------------------------------------- */ 4208 /* 4209 * The PCI-8604PW contains a CPLD, probably an ispMACH 4A, that filters 4210 * the PCI REQ signals comming from the four BT878 chips. After power 4211 * up, the CPLD does not forward requests to the bus, which prevents 4212 * the BT878 from fetching RISC instructions from memory. While the 4213 * CPLD is connected to most of the GPIOs of PCI device 0xD, only 4214 * five appear to play a role in unlocking the REQ signal. The following 4215 * sequence has been determined by trial and error without access to the 4216 * original driver. 4217 * 4218 * Eight GPIOs of device 0xC are provided on connector CN4 (4 in, 4 out). 4219 * Devices 0xE and 0xF do not appear to have anything connected to their 4220 * GPIOs. 4221 * 4222 * The correct GPIO_OUT_EN value might have some more bits set. It should 4223 * be possible to derive it from a boundary scan of the CPLD. Its JTAG 4224 * pins are routed to test points. 4225 * 4226 */ 4227 /* ----------------------------------------------------------------------- */ 4228 static void 4229 init_PCI8604PW(struct bttv *btv) 4230 { 4231 int state; 4232 4233 if ((PCI_SLOT(btv->c.pci->devfn) & ~3) != 0xC) { 4234 pr_warn("This is not a PCI-8604PW\n"); 4235 return; 4236 } 4237 4238 if (PCI_SLOT(btv->c.pci->devfn) != 0xD) 4239 return; 4240 4241 btwrite(0x080002, BT848_GPIO_OUT_EN); 4242 4243 state = (btread(BT848_GPIO_DATA) >> 21) & 7; 4244 4245 for (;;) { 4246 switch (state) { 4247 case 1: 4248 case 5: 4249 case 6: 4250 case 4: 4251 pr_debug("PCI-8604PW in state %i, toggling pin\n", 4252 state); 4253 btwrite(0x080000, BT848_GPIO_DATA); 4254 msleep(1); 4255 btwrite(0x000000, BT848_GPIO_DATA); 4256 msleep(1); 4257 break; 4258 case 7: 4259 pr_info("PCI-8604PW unlocked\n"); 4260 return; 4261 case 0: 4262 /* FIXME: If we are in state 7 and toggle GPIO[19] one 4263 more time, the CPLD goes into state 0, where PCI bus 4264 mastering is inhibited again. We have not managed to 4265 get out of that state. */ 4266 4267 pr_err("PCI-8604PW locked until reset\n"); 4268 return; 4269 default: 4270 pr_err("PCI-8604PW in unknown state %i\n", state); 4271 return; 4272 } 4273 4274 state = (state << 4) | ((btread(BT848_GPIO_DATA) >> 21) & 7); 4275 4276 switch (state) { 4277 case 0x15: 4278 case 0x56: 4279 case 0x64: 4280 case 0x47: 4281 /* The transition from state 7 to state 0 is, as explained 4282 above, valid but undesired and with this code impossible 4283 as we exit as soon as we are in state 7. 4284 case 0x70: */ 4285 break; 4286 default: 4287 pr_err("PCI-8604PW invalid transition %i -> %i\n", 4288 state >> 4, state & 7); 4289 return; 4290 } 4291 state &= 7; 4292 } 4293 } 4294 4295 4296 4297 /* ----------------------------------------------------------------------- */ 4298 /* Miro Pro radio stuff -- the tea5757 is connected to some GPIO ports */ 4299 /* 4300 * Copyright (c) 1999 Csaba Halasz <qgehali@uni-miskolc.hu> 4301 * This code is placed under the terms of the GNU General Public License 4302 * 4303 * Brutally hacked by Dan Sheridan <dan.sheridan@contact.org.uk> djs52 8/3/00 4304 */ 4305 4306 static void bus_low(struct bttv *btv, int bit) 4307 { 4308 if (btv->mbox_ior) { 4309 gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel, 4310 btv->mbox_ior | btv->mbox_iow | btv->mbox_csel); 4311 udelay(5); 4312 } 4313 4314 gpio_bits(bit,0); 4315 udelay(5); 4316 4317 if (btv->mbox_ior) { 4318 gpio_bits(btv->mbox_iow | btv->mbox_csel, 0); 4319 udelay(5); 4320 } 4321 } 4322 4323 static void bus_high(struct bttv *btv, int bit) 4324 { 4325 if (btv->mbox_ior) { 4326 gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel, 4327 btv->mbox_ior | btv->mbox_iow | btv->mbox_csel); 4328 udelay(5); 4329 } 4330 4331 gpio_bits(bit,bit); 4332 udelay(5); 4333 4334 if (btv->mbox_ior) { 4335 gpio_bits(btv->mbox_iow | btv->mbox_csel, 0); 4336 udelay(5); 4337 } 4338 } 4339 4340 static int bus_in(struct bttv *btv, int bit) 4341 { 4342 if (btv->mbox_ior) { 4343 gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel, 4344 btv->mbox_ior | btv->mbox_iow | btv->mbox_csel); 4345 udelay(5); 4346 4347 gpio_bits(btv->mbox_iow | btv->mbox_csel, 0); 4348 udelay(5); 4349 } 4350 return gpio_read() & (bit); 4351 } 4352 4353 /* TEA5757 register bits */ 4354 #define TEA_FREQ 0:14 4355 #define TEA_BUFFER 15:15 4356 4357 #define TEA_SIGNAL_STRENGTH 16:17 4358 4359 #define TEA_PORT1 18:18 4360 #define TEA_PORT0 19:19 4361 4362 #define TEA_BAND 20:21 4363 #define TEA_BAND_FM 0 4364 #define TEA_BAND_MW 1 4365 #define TEA_BAND_LW 2 4366 #define TEA_BAND_SW 3 4367 4368 #define TEA_MONO 22:22 4369 #define TEA_ALLOW_STEREO 0 4370 #define TEA_FORCE_MONO 1 4371 4372 #define TEA_SEARCH_DIRECTION 23:23 4373 #define TEA_SEARCH_DOWN 0 4374 #define TEA_SEARCH_UP 1 4375 4376 #define TEA_STATUS 24:24 4377 #define TEA_STATUS_TUNED 0 4378 #define TEA_STATUS_SEARCHING 1 4379 4380 /* Low-level stuff */ 4381 static int tea5757_read(struct bttv *btv) 4382 { 4383 unsigned long timeout; 4384 int value = 0; 4385 int i; 4386 4387 /* better safe than sorry */ 4388 gpio_inout(btv->mbox_mask, btv->mbox_clk | btv->mbox_we); 4389 4390 if (btv->mbox_ior) { 4391 gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel, 4392 btv->mbox_ior | btv->mbox_iow | btv->mbox_csel); 4393 udelay(5); 4394 } 4395 4396 if (bttv_gpio) 4397 bttv_gpio_tracking(btv,"tea5757 read"); 4398 4399 bus_low(btv,btv->mbox_we); 4400 bus_low(btv,btv->mbox_clk); 4401 4402 udelay(10); 4403 timeout= jiffies + msecs_to_jiffies(1000); 4404 4405 /* wait for DATA line to go low; error if it doesn't */ 4406 while (bus_in(btv,btv->mbox_data) && time_before(jiffies, timeout)) 4407 schedule(); 4408 if (bus_in(btv,btv->mbox_data)) { 4409 pr_warn("%d: tea5757: read timeout\n", btv->c.nr); 4410 return -1; 4411 } 4412 4413 dprintk("%d: tea5757:", btv->c.nr); 4414 for (i = 0; i < 24; i++) { 4415 udelay(5); 4416 bus_high(btv,btv->mbox_clk); 4417 udelay(5); 4418 dprintk_cont("%c", 4419 bus_in(btv, btv->mbox_most) == 0 ? 'T' : '-'); 4420 bus_low(btv,btv->mbox_clk); 4421 value <<= 1; 4422 value |= (bus_in(btv,btv->mbox_data) == 0)?0:1; /* MSB first */ 4423 dprintk_cont("%c", 4424 bus_in(btv, btv->mbox_most) == 0 ? 'S' : 'M'); 4425 } 4426 dprintk_cont("\n"); 4427 dprintk("%d: tea5757: read 0x%X\n", btv->c.nr, value); 4428 return value; 4429 } 4430 4431 static int tea5757_write(struct bttv *btv, int value) 4432 { 4433 int i; 4434 int reg = value; 4435 4436 gpio_inout(btv->mbox_mask, btv->mbox_clk | btv->mbox_we | btv->mbox_data); 4437 4438 if (btv->mbox_ior) { 4439 gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel, 4440 btv->mbox_ior | btv->mbox_iow | btv->mbox_csel); 4441 udelay(5); 4442 } 4443 if (bttv_gpio) 4444 bttv_gpio_tracking(btv,"tea5757 write"); 4445 4446 dprintk("%d: tea5757: write 0x%X\n", btv->c.nr, value); 4447 bus_low(btv,btv->mbox_clk); 4448 bus_high(btv,btv->mbox_we); 4449 for (i = 0; i < 25; i++) { 4450 if (reg & 0x1000000) 4451 bus_high(btv,btv->mbox_data); 4452 else 4453 bus_low(btv,btv->mbox_data); 4454 reg <<= 1; 4455 bus_high(btv,btv->mbox_clk); 4456 udelay(10); 4457 bus_low(btv,btv->mbox_clk); 4458 udelay(10); 4459 } 4460 bus_low(btv,btv->mbox_we); /* unmute !!! */ 4461 return 0; 4462 } 4463 4464 void tea5757_set_freq(struct bttv *btv, unsigned short freq) 4465 { 4466 dprintk("tea5757_set_freq %d\n",freq); 4467 tea5757_write(btv, 5 * freq + 0x358); /* add 10.7MHz (see docs) */ 4468 } 4469 4470 /* RemoteVision MX (rv605) muxsel helper [Miguel Freitas] 4471 * 4472 * This is needed because rv605 don't use a normal multiplex, but a crosspoint 4473 * switch instead (CD22M3494E). This IC can have multiple active connections 4474 * between Xn (input) and Yn (output) pins. We need to clear any existing 4475 * connection prior to establish a new one, pulsing the STROBE pin. 4476 * 4477 * The board hardwire Y0 (xpoint) to MUX1 and MUXOUT to Yin. 4478 * GPIO pins are wired as: 4479 * GPIO[0:3] - AX[0:3] (xpoint) - P1[0:3] (microcontroller) 4480 * GPIO[4:6] - AY[0:2] (xpoint) - P1[4:6] (microcontroller) 4481 * GPIO[7] - DATA (xpoint) - P1[7] (microcontroller) 4482 * GPIO[8] - - P3[5] (microcontroller) 4483 * GPIO[9] - RESET (xpoint) - P3[6] (microcontroller) 4484 * GPIO[10] - STROBE (xpoint) - P3[7] (microcontroller) 4485 * GPINTR - - P3[4] (microcontroller) 4486 * 4487 * The microcontroller is a 80C32 like. It should be possible to change xpoint 4488 * configuration either directly (as we are doing) or using the microcontroller 4489 * which is also wired to I2C interface. I have no further info on the 4490 * microcontroller features, one would need to disassembly the firmware. 4491 * note: the vendor refused to give any information on this product, all 4492 * that stuff was found using a multimeter! :) 4493 */ 4494 static void rv605_muxsel(struct bttv *btv, unsigned int input) 4495 { 4496 static const u8 muxgpio[] = { 0x3, 0x1, 0x2, 0x4, 0xf, 0x7, 0xe, 0x0, 4497 0xd, 0xb, 0xc, 0x6, 0x9, 0x5, 0x8, 0xa }; 4498 4499 gpio_bits(0x07f, muxgpio[input]); 4500 4501 /* reset all conections */ 4502 gpio_bits(0x200,0x200); 4503 mdelay(1); 4504 gpio_bits(0x200,0x000); 4505 mdelay(1); 4506 4507 /* create a new connection */ 4508 gpio_bits(0x480,0x480); 4509 mdelay(1); 4510 gpio_bits(0x480,0x080); 4511 mdelay(1); 4512 } 4513 4514 /* Tibet Systems 'Progress DVR' CS16 muxsel helper [Chris Fanning] 4515 * 4516 * The CS16 (available on eBay cheap) is a PCI board with four Fusion 4517 * 878A chips, a PCI bridge, an Atmel microcontroller, four sync separator 4518 * chips, ten eight input analog multiplexors, a not chip and a few 4519 * other components. 4520 * 4521 * 16 inputs on a secondary bracket are provided and can be selected 4522 * from each of the four capture chips. Two of the eight input 4523 * multiplexors are used to select from any of the 16 input signals. 4524 * 4525 * Unsupported hardware capabilities: 4526 * . A video output monitor on the secondary bracket can be selected from 4527 * one of the 878A chips. 4528 * . Another passthrough but I haven't spent any time investigating it. 4529 * . Digital I/O (logic level connected to GPIO) is available from an 4530 * onboard header. 4531 * 4532 * The on chip input mux should always be set to 2. 4533 * GPIO[16:19] - Video input selection 4534 * GPIO[0:3] - Video output monitor select (only available from one 878A) 4535 * GPIO[?:?] - Digital I/O. 4536 * 4537 * There is an ATMEL microcontroller with an 8031 core on board. I have not 4538 * determined what function (if any) it provides. With the microcontroller 4539 * and sync separator chips a guess is that it might have to do with video 4540 * switching and maybe some digital I/O. 4541 */ 4542 static void tibetCS16_muxsel(struct bttv *btv, unsigned int input) 4543 { 4544 /* video mux */ 4545 gpio_bits(0x0f0000, input << 16); 4546 } 4547 4548 static void tibetCS16_init(struct bttv *btv) 4549 { 4550 /* enable gpio bits, mask obtained via btSpy */ 4551 gpio_inout(0xffffff, 0x0f7fff); 4552 gpio_write(0x0f7fff); 4553 } 4554 4555 /* 4556 * The following routines for the Kodicom-4400r get a little mind-twisting. 4557 * There is a "master" controller and three "slave" controllers, together 4558 * an analog switch which connects any of 16 cameras to any of the BT87A's. 4559 * The analog switch is controlled by the "master", but the detection order 4560 * of the four BT878A chips is in an order which I just don't understand. 4561 * The "master" is actually the second controller to be detected. The 4562 * logic on the board uses logical numbers for the 4 controllers, but 4563 * those numbers are different from the detection sequence. When working 4564 * with the analog switch, we need to "map" from the detection sequence 4565 * over to the board's logical controller number. This mapping sequence 4566 * is {3, 0, 2, 1}, i.e. the first controller to be detected is logical 4567 * unit 3, the second (which is the master) is logical unit 0, etc. 4568 * We need to maintain the status of the analog switch (which of the 16 4569 * cameras is connected to which of the 4 controllers) in sw_status array. 4570 */ 4571 4572 /* 4573 * First a routine to set the analog switch, which controls which camera 4574 * is routed to which controller. The switch comprises an X-address 4575 * (gpio bits 0-3, representing the camera, ranging from 0-15), and a 4576 * Y-address (gpio bits 4-6, representing the controller, ranging from 0-3). 4577 * A data value (gpio bit 7) of '1' enables the switch, and '0' disables 4578 * the switch. A STROBE bit (gpio bit 8) latches the data value into the 4579 * specified address. The idea is to set the address and data, then bring 4580 * STROBE high, and finally bring STROBE back to low. 4581 */ 4582 static void kodicom4400r_write(struct bttv *btv, 4583 unsigned char xaddr, 4584 unsigned char yaddr, 4585 unsigned char data) { 4586 unsigned int udata; 4587 4588 udata = (data << 7) | ((yaddr&3) << 4) | (xaddr&0xf); 4589 gpio_bits(0x1ff, udata); /* write ADDR and DAT */ 4590 gpio_bits(0x1ff, udata | (1 << 8)); /* strobe high */ 4591 gpio_bits(0x1ff, udata); /* strobe low */ 4592 } 4593 4594 /* 4595 * Next the mux select. Both the "master" and "slave" 'cards' (controllers) 4596 * use this routine. The routine finds the "master" for the card, maps 4597 * the controller number from the detected position over to the logical 4598 * number, writes the appropriate data to the analog switch, and housekeeps 4599 * the local copy of the switch information. The parameter 'input' is the 4600 * requested camera number (0 - 15). 4601 */ 4602 static void kodicom4400r_muxsel(struct bttv *btv, unsigned int input) 4603 { 4604 int xaddr, yaddr; 4605 struct bttv *mctlr; 4606 static unsigned char map[4] = {3, 0, 2, 1}; 4607 4608 mctlr = master[btv->c.nr]; 4609 if (mctlr == NULL) { /* ignore if master not yet detected */ 4610 return; 4611 } 4612 yaddr = (btv->c.nr - mctlr->c.nr + 1) & 3; /* the '&' is for safety */ 4613 yaddr = map[yaddr]; 4614 xaddr = input & 0xf; 4615 /* Check if the controller/camera pair has changed, else ignore */ 4616 if (mctlr->sw_status[yaddr] != xaddr) 4617 { 4618 /* "open" the old switch, "close" the new one, save the new */ 4619 kodicom4400r_write(mctlr, mctlr->sw_status[yaddr], yaddr, 0); 4620 mctlr->sw_status[yaddr] = xaddr; 4621 kodicom4400r_write(mctlr, xaddr, yaddr, 1); 4622 } 4623 } 4624 4625 /* 4626 * During initialisation, we need to reset the analog switch. We 4627 * also preset the switch to map the 4 connectors on the card to the 4628 * *user's* (see above description of kodicom4400r_muxsel) channels 4629 * 0 through 3 4630 */ 4631 static void kodicom4400r_init(struct bttv *btv) 4632 { 4633 int ix; 4634 4635 gpio_inout(0x0003ff, 0x0003ff); 4636 gpio_write(1 << 9); /* reset MUX */ 4637 gpio_write(0); 4638 /* Preset camera 0 to the 4 controllers */ 4639 for (ix = 0; ix < 4; ix++) { 4640 btv->sw_status[ix] = ix; 4641 kodicom4400r_write(btv, ix, ix, 1); 4642 } 4643 /* 4644 * Since this is the "master", we need to set up the 4645 * other three controller chips' pointers to this structure 4646 * for later use in the muxsel routine. 4647 */ 4648 if ((btv->c.nr<1) || (btv->c.nr>BTTV_MAX-3)) 4649 return; 4650 master[btv->c.nr-1] = btv; 4651 master[btv->c.nr] = btv; 4652 master[btv->c.nr+1] = btv; 4653 master[btv->c.nr+2] = btv; 4654 } 4655 4656 /* The Grandtec X-Guard framegrabber card uses two Dual 4-channel 4657 * video multiplexers to provide up to 16 video inputs. These 4658 * multiplexers are controlled by the lower 8 GPIO pins of the 4659 * bt878. The multiplexers probably Pericom PI5V331Q or similar. 4660 4661 * xxx0 is pin xxx of multiplexer U5, 4662 * yyy1 is pin yyy of multiplexer U2 4663 */ 4664 #define ENA0 0x01 4665 #define ENB0 0x02 4666 #define ENA1 0x04 4667 #define ENB1 0x08 4668 4669 #define IN10 0x10 4670 #define IN00 0x20 4671 #define IN11 0x40 4672 #define IN01 0x80 4673 4674 static void xguard_muxsel(struct bttv *btv, unsigned int input) 4675 { 4676 static const int masks[] = { 4677 ENB0, ENB0|IN00, ENB0|IN10, ENB0|IN00|IN10, 4678 ENA0, ENA0|IN00, ENA0|IN10, ENA0|IN00|IN10, 4679 ENB1, ENB1|IN01, ENB1|IN11, ENB1|IN01|IN11, 4680 ENA1, ENA1|IN01, ENA1|IN11, ENA1|IN01|IN11, 4681 }; 4682 gpio_write(masks[input%16]); 4683 } 4684 static void picolo_tetra_init(struct bttv *btv) 4685 { 4686 /*This is the video input redirection fonctionality : I DID NOT USED IT. */ 4687 btwrite (0x08<<16,BT848_GPIO_DATA);/*GPIO[19] [==> 4053 B+C] set to 1 */ 4688 btwrite (0x04<<16,BT848_GPIO_DATA);/*GPIO[18] [==> 4053 A] set to 1*/ 4689 } 4690 static void picolo_tetra_muxsel (struct bttv* btv, unsigned int input) 4691 { 4692 4693 dprintk("%d : picolo_tetra_muxsel => input = %d\n", btv->c.nr, input); 4694 /*Just set the right path in the analog multiplexers : channel 1 -> 4 ==> Analog Mux ==> MUX0*/ 4695 /*GPIO[20]&GPIO[21] used to choose the right input*/ 4696 btwrite (input<<20,BT848_GPIO_DATA); 4697 4698 } 4699 4700 /* 4701 * ivc120_muxsel [Added by Alan Garfield <alan@fromorbit.com>] 4702 * 4703 * The IVC120G security card has 4 i2c controlled TDA8540 matrix 4704 * swichers to provide 16 channels to MUX0. The TDA8540's have 4705 * 4 independent outputs and as such the IVC120G also has the 4706 * optional "Monitor Out" bus. This allows the card to be looking 4707 * at one input while the monitor is looking at another. 4708 * 4709 * Since I've couldn't be bothered figuring out how to add an 4710 * independent muxsel for the monitor bus, I've just set it to 4711 * whatever the card is looking at. 4712 * 4713 * OUT0 of the TDA8540's is connected to MUX0 (0x03) 4714 * OUT1 of the TDA8540's is connected to "Monitor Out" (0x0C) 4715 * 4716 * TDA8540_ALT3 IN0-3 = Channel 13 - 16 (0x03) 4717 * TDA8540_ALT4 IN0-3 = Channel 1 - 4 (0x03) 4718 * TDA8540_ALT5 IN0-3 = Channel 5 - 8 (0x03) 4719 * TDA8540_ALT6 IN0-3 = Channel 9 - 12 (0x03) 4720 * 4721 */ 4722 4723 /* All 7 possible sub-ids for the TDA8540 Matrix Switcher */ 4724 #define I2C_TDA8540 0x90 4725 #define I2C_TDA8540_ALT1 0x92 4726 #define I2C_TDA8540_ALT2 0x94 4727 #define I2C_TDA8540_ALT3 0x96 4728 #define I2C_TDA8540_ALT4 0x98 4729 #define I2C_TDA8540_ALT5 0x9a 4730 #define I2C_TDA8540_ALT6 0x9c 4731 4732 static void ivc120_muxsel(struct bttv *btv, unsigned int input) 4733 { 4734 /* Simple maths */ 4735 int key = input % 4; 4736 int matrix = input / 4; 4737 4738 dprintk("%d: ivc120_muxsel: Input - %02d | TDA - %02d | In - %02d\n", 4739 btv->c.nr, input, matrix, key); 4740 4741 /* Handles the input selection on the TDA8540's */ 4742 bttv_I2CWrite(btv, I2C_TDA8540_ALT3, 0x00, 4743 ((matrix == 3) ? (key | key << 2) : 0x00), 1); 4744 bttv_I2CWrite(btv, I2C_TDA8540_ALT4, 0x00, 4745 ((matrix == 0) ? (key | key << 2) : 0x00), 1); 4746 bttv_I2CWrite(btv, I2C_TDA8540_ALT5, 0x00, 4747 ((matrix == 1) ? (key | key << 2) : 0x00), 1); 4748 bttv_I2CWrite(btv, I2C_TDA8540_ALT6, 0x00, 4749 ((matrix == 2) ? (key | key << 2) : 0x00), 1); 4750 4751 /* Handles the output enables on the TDA8540's */ 4752 bttv_I2CWrite(btv, I2C_TDA8540_ALT3, 0x02, 4753 ((matrix == 3) ? 0x03 : 0x00), 1); /* 13 - 16 */ 4754 bttv_I2CWrite(btv, I2C_TDA8540_ALT4, 0x02, 4755 ((matrix == 0) ? 0x03 : 0x00), 1); /* 1-4 */ 4756 bttv_I2CWrite(btv, I2C_TDA8540_ALT5, 0x02, 4757 ((matrix == 1) ? 0x03 : 0x00), 1); /* 5-8 */ 4758 bttv_I2CWrite(btv, I2C_TDA8540_ALT6, 0x02, 4759 ((matrix == 2) ? 0x03 : 0x00), 1); /* 9-12 */ 4760 4761 /* 878's MUX0 is already selected for input via muxsel values */ 4762 } 4763 4764 4765 /* PXC200 muxsel helper 4766 * luke@syseng.anu.edu.au 4767 * another transplant 4768 * from Alessandro Rubini (rubini@linux.it) 4769 * 4770 * There are 4 kinds of cards: 4771 * PXC200L which is bt848 4772 * PXC200F which is bt848 with PIC controlling mux 4773 * PXC200AL which is bt878 4774 * PXC200AF which is bt878 with PIC controlling mux 4775 */ 4776 #define PX_CFG_PXC200F 0x01 4777 #define PX_FLAG_PXC200A 0x00001000 /* a pxc200A is bt-878 based */ 4778 #define PX_I2C_PIC 0x0f 4779 #define PX_PXC200A_CARDID 0x200a1295 4780 #define PX_I2C_CMD_CFG 0x00 4781 4782 static void PXC200_muxsel(struct bttv *btv, unsigned int input) 4783 { 4784 int rc; 4785 long mux; 4786 int bitmask; 4787 unsigned char buf[2]; 4788 4789 /* Read PIC config to determine if this is a PXC200F */ 4790 /* PX_I2C_CMD_CFG*/ 4791 buf[0]=0; 4792 buf[1]=0; 4793 rc=bttv_I2CWrite(btv,(PX_I2C_PIC<<1),buf[0],buf[1],1); 4794 if (rc) { 4795 pr_debug("%d: PXC200_muxsel: pic cfg write failed:%d\n", 4796 btv->c.nr, rc); 4797 /* not PXC ? do nothing */ 4798 return; 4799 } 4800 4801 rc=bttv_I2CRead(btv,(PX_I2C_PIC<<1),NULL); 4802 if (!(rc & PX_CFG_PXC200F)) { 4803 pr_debug("%d: PXC200_muxsel: not PXC200F rc:%d\n", 4804 btv->c.nr, rc); 4805 return; 4806 } 4807 4808 4809 /* The multiplexer in the 200F is handled by the GPIO port */ 4810 /* get correct mapping between inputs */ 4811 /* mux = bttv_tvcards[btv->type].muxsel[input] & 3; */ 4812 /* ** not needed!? */ 4813 mux = input; 4814 4815 /* make sure output pins are enabled */ 4816 /* bitmask=0x30f; */ 4817 bitmask=0x302; 4818 /* check whether we have a PXC200A */ 4819 if (btv->cardid == PX_PXC200A_CARDID) { 4820 bitmask ^= 0x180; /* use 7 and 9, not 8 and 9 */ 4821 bitmask |= 7<<4; /* the DAC */ 4822 } 4823 btwrite(bitmask, BT848_GPIO_OUT_EN); 4824 4825 bitmask = btread(BT848_GPIO_DATA); 4826 if (btv->cardid == PX_PXC200A_CARDID) 4827 bitmask = (bitmask & ~0x280) | ((mux & 2) << 8) | ((mux & 1) << 7); 4828 else /* older device */ 4829 bitmask = (bitmask & ~0x300) | ((mux & 3) << 8); 4830 btwrite(bitmask,BT848_GPIO_DATA); 4831 4832 /* 4833 * Was "to be safe, set the bt848 to input 0" 4834 * Actually, since it's ok at load time, better not messing 4835 * with these bits (on PXC200AF you need to set mux 2 here) 4836 * 4837 * needed because bttv-driver sets mux before calling this function 4838 */ 4839 if (btv->cardid == PX_PXC200A_CARDID) 4840 btaor(2<<5, ~BT848_IFORM_MUXSEL, BT848_IFORM); 4841 else /* older device */ 4842 btand(~BT848_IFORM_MUXSEL,BT848_IFORM); 4843 4844 pr_debug("%d: setting input channel to:%d\n", btv->c.nr, (int)mux); 4845 } 4846 4847 static void phytec_muxsel(struct bttv *btv, unsigned int input) 4848 { 4849 unsigned int mux = input % 4; 4850 4851 if (input == btv->svhs) 4852 mux = 0; 4853 4854 gpio_bits(0x3, mux); 4855 } 4856 4857 /* 4858 * GeoVision GV-800(S) functions 4859 * Bruno Christo <bchristo@inf.ufsm.br> 4860 */ 4861 4862 /* This is a function to control the analog switch, which determines which 4863 * camera is routed to which controller. The switch comprises an X-address 4864 * (gpio bits 0-3, representing the camera, ranging from 0-15), and a 4865 * Y-address (gpio bits 4-6, representing the controller, ranging from 0-3). 4866 * A data value (gpio bit 18) of '1' enables the switch, and '0' disables 4867 * the switch. A STROBE bit (gpio bit 17) latches the data value into the 4868 * specified address. There is also a chip select (gpio bit 16). 4869 * The idea is to set the address and chip select together, bring 4870 * STROBE high, write the data, and finally bring STROBE back to low. 4871 */ 4872 static void gv800s_write(struct bttv *btv, 4873 unsigned char xaddr, 4874 unsigned char yaddr, 4875 unsigned char data) { 4876 /* On the "master" 878A: 4877 * GPIO bits 0-9 are used for the analog switch: 4878 * 00 - 03: camera selector 4879 * 04 - 06: 878A (controller) selector 4880 * 16: cselect 4881 * 17: strobe 4882 * 18: data (1->on, 0->off) 4883 * 19: reset 4884 */ 4885 const u32 ADDRESS = ((xaddr&0xf) | (yaddr&3)<<4); 4886 const u32 CSELECT = 1<<16; 4887 const u32 STROBE = 1<<17; 4888 const u32 DATA = data<<18; 4889 4890 gpio_bits(0x1007f, ADDRESS | CSELECT); /* write ADDRESS and CSELECT */ 4891 gpio_bits(0x20000, STROBE); /* STROBE high */ 4892 gpio_bits(0x40000, DATA); /* write DATA */ 4893 gpio_bits(0x20000, ~STROBE); /* STROBE low */ 4894 } 4895 4896 /* 4897 * GeoVision GV-800(S) muxsel 4898 * 4899 * Each of the 4 cards (controllers) use this function. 4900 * The controller using this function selects the input through the GPIO pins 4901 * of the "master" card. A pointer to this card is stored in master[btv->c.nr]. 4902 * 4903 * The parameter 'input' is the requested camera number (0-4) on the controller. 4904 * The map array has the address of each input. Note that the addresses in the 4905 * array are in the sequence the original GeoVision driver uses, that is, set 4906 * every controller to input 0, then to input 1, 2, 3, repeat. This means that 4907 * the physical "camera 1" connector corresponds to controller 0 input 0, 4908 * "camera 2" corresponds to controller 1 input 0, and so on. 4909 * 4910 * After getting the input address, the function then writes the appropriate 4911 * data to the analog switch, and housekeeps the local copy of the switch 4912 * information. 4913 */ 4914 static void gv800s_muxsel(struct bttv *btv, unsigned int input) 4915 { 4916 struct bttv *mctlr; 4917 int xaddr, yaddr; 4918 static unsigned int map[4][4] = { { 0x0, 0x4, 0xa, 0x6 }, 4919 { 0x1, 0x5, 0xb, 0x7 }, 4920 { 0x2, 0x8, 0xc, 0xe }, 4921 { 0x3, 0x9, 0xd, 0xf } }; 4922 input = input%4; 4923 mctlr = master[btv->c.nr]; 4924 if (mctlr == NULL) { 4925 /* do nothing until the "master" is detected */ 4926 return; 4927 } 4928 yaddr = (btv->c.nr - mctlr->c.nr) & 3; 4929 xaddr = map[yaddr][input] & 0xf; 4930 4931 /* Check if the controller/camera pair has changed, ignore otherwise */ 4932 if (mctlr->sw_status[yaddr] != xaddr) { 4933 /* disable the old switch, enable the new one and save status */ 4934 gv800s_write(mctlr, mctlr->sw_status[yaddr], yaddr, 0); 4935 mctlr->sw_status[yaddr] = xaddr; 4936 gv800s_write(mctlr, xaddr, yaddr, 1); 4937 } 4938 } 4939 4940 /* GeoVision GV-800(S) "master" chip init */ 4941 static void gv800s_init(struct bttv *btv) 4942 { 4943 int ix; 4944 4945 gpio_inout(0xf107f, 0xf107f); 4946 gpio_write(1<<19); /* reset the analog MUX */ 4947 gpio_write(0); 4948 4949 /* Preset camera 0 to the 4 controllers */ 4950 for (ix = 0; ix < 4; ix++) { 4951 btv->sw_status[ix] = ix; 4952 gv800s_write(btv, ix, ix, 1); 4953 } 4954 4955 /* Inputs on the "master" controller need this brightness fix */ 4956 bttv_I2CWrite(btv, 0x18, 0x5, 0x90, 1); 4957 4958 if (btv->c.nr > BTTV_MAX-4) 4959 return; 4960 /* 4961 * Store the "master" controller pointer in the master 4962 * array for later use in the muxsel function. 4963 */ 4964 master[btv->c.nr] = btv; 4965 master[btv->c.nr+1] = btv; 4966 master[btv->c.nr+2] = btv; 4967 master[btv->c.nr+3] = btv; 4968 } 4969 4970 /* ----------------------------------------------------------------------- */ 4971 /* motherboard chipset specific stuff */ 4972 4973 void __init bttv_check_chipset(void) 4974 { 4975 int pcipci_fail = 0; 4976 struct pci_dev *dev = NULL; 4977 4978 if (pci_pci_problems & (PCIPCI_FAIL|PCIAGP_FAIL)) /* should check if target is AGP */ 4979 pcipci_fail = 1; 4980 if (pci_pci_problems & (PCIPCI_TRITON|PCIPCI_NATOMA|PCIPCI_VIAETBF)) 4981 triton1 = 1; 4982 if (pci_pci_problems & PCIPCI_VSFX) 4983 vsfx = 1; 4984 #ifdef PCIPCI_ALIMAGIK 4985 if (pci_pci_problems & PCIPCI_ALIMAGIK) 4986 latency = 0x0A; 4987 #endif 4988 4989 4990 /* print warnings about any quirks found */ 4991 if (triton1) 4992 pr_info("Host bridge needs ETBF enabled\n"); 4993 if (vsfx) 4994 pr_info("Host bridge needs VSFX enabled\n"); 4995 if (pcipci_fail) { 4996 pr_info("bttv and your chipset may not work together\n"); 4997 if (!no_overlay) { 4998 pr_info("overlay will be disabled\n"); 4999 no_overlay = 1; 5000 } else { 5001 pr_info("overlay forced. Use this option at your own risk.\n"); 5002 } 5003 } 5004 if (UNSET != latency) 5005 pr_info("pci latency fixup [%d]\n", latency); 5006 while ((dev = pci_get_device(PCI_VENDOR_ID_INTEL, 5007 PCI_DEVICE_ID_INTEL_82441, dev))) { 5008 unsigned char b; 5009 pci_read_config_byte(dev, 0x53, &b); 5010 if (bttv_debug) 5011 pr_info("Host bridge: 82441FX Natoma, bufcon=0x%02x\n", 5012 b); 5013 } 5014 } 5015 5016 int bttv_handle_chipset(struct bttv *btv) 5017 { 5018 unsigned char command; 5019 5020 if (!triton1 && !vsfx && UNSET == latency) 5021 return 0; 5022 5023 if (bttv_verbose) { 5024 if (triton1) 5025 pr_info("%d: enabling ETBF (430FX/VP3 compatibility)\n", 5026 btv->c.nr); 5027 if (vsfx && btv->id >= 878) 5028 pr_info("%d: enabling VSFX\n", btv->c.nr); 5029 if (UNSET != latency) 5030 pr_info("%d: setting pci timer to %d\n", 5031 btv->c.nr, latency); 5032 } 5033 5034 if (btv->id < 878) { 5035 /* bt848 (mis)uses a bit in the irq mask for etbf */ 5036 if (triton1) 5037 btv->triton1 = BT848_INT_ETBF; 5038 } else { 5039 /* bt878 has a bit in the pci config space for it */ 5040 pci_read_config_byte(btv->c.pci, BT878_DEVCTRL, &command); 5041 if (triton1) 5042 command |= BT878_EN_TBFX; 5043 if (vsfx) 5044 command |= BT878_EN_VSFX; 5045 pci_write_config_byte(btv->c.pci, BT878_DEVCTRL, command); 5046 } 5047 if (UNSET != latency) 5048 pci_write_config_byte(btv->c.pci, PCI_LATENCY_TIMER, latency); 5049 return 0; 5050 } 5051 5052 5053 /* 5054 * Local variables: 5055 * c-basic-offset: 8 5056 * End: 5057 */ 5058