1# 2# Touchscreen driver configuration 3# 4menuconfig INPUT_TOUCHSCREEN 5 bool "Touchscreens" 6 help 7 Say Y here, and a list of supported touchscreens will be displayed. 8 This option doesn't affect the kernel. 9 10 If unsure, say Y. 11 12if INPUT_TOUCHSCREEN 13 14config TOUCHSCREEN_ADS7846 15 tristate "ADS7846/TSC2046 and ADS7843 based touchscreens" 16 depends on SPI_MASTER 17 depends on HWMON = n || HWMON 18 help 19 Say Y here if you have a touchscreen interface using the 20 ADS7846/TSC2046 or ADS7843 controller, and your board-specific 21 setup code includes that in its table of SPI devices. 22 23 If HWMON is selected, and the driver is told the reference voltage 24 on your board, you will also get hwmon interfaces for the voltage 25 (and on ads7846/tsc2046, temperature) sensors of this chip. 26 27 If unsure, say N (but it's safe to say "Y"). 28 29 To compile this driver as a module, choose M here: the 30 module will be called ads7846. 31 32config TOUCHSCREEN_BITSY 33 tristate "Compaq iPAQ H3600 (Bitsy) touchscreen" 34 depends on SA1100_BITSY 35 select SERIO 36 help 37 Say Y here if you have the h3600 (Bitsy) touchscreen. 38 39 If unsure, say N. 40 41 To compile this driver as a module, choose M here: the 42 module will be called h3600_ts_input. 43 44config TOUCHSCREEN_CORGI 45 tristate "SharpSL (Corgi and Spitz series) touchscreen driver" 46 depends on PXA_SHARPSL 47 default y 48 help 49 Say Y here to enable the driver for the touchscreen on the 50 Sharp SL-C7xx and SL-Cxx00 series of PDAs. 51 52 If unsure, say N. 53 54 To compile this driver as a module, choose M here: the 55 module will be called corgi_ts. 56 57config TOUCHSCREEN_FUJITSU 58 tristate "Fujitsu serial touchscreen" 59 select SERIO 60 help 61 Say Y here if you have the Fujitsu touchscreen (such as one 62 installed in Lifebook P series laptop) connected to your 63 system. 64 65 If unsure, say N. 66 67 To compile this driver as a module, choose M here: the 68 module will be called fujitsu-ts. 69 70config TOUCHSCREEN_GUNZE 71 tristate "Gunze AHL-51S touchscreen" 72 select SERIO 73 help 74 Say Y here if you have the Gunze AHL-51 touchscreen connected to 75 your system. 76 77 If unsure, say N. 78 79 To compile this driver as a module, choose M here: the 80 module will be called gunze. 81 82config TOUCHSCREEN_ELO 83 tristate "Elo serial touchscreens" 84 select SERIO 85 help 86 Say Y here if you have an Elo serial touchscreen connected to 87 your system. 88 89 If unsure, say N. 90 91 To compile this driver as a module, choose M here: the 92 module will be called elo. 93 94config TOUCHSCREEN_MTOUCH 95 tristate "MicroTouch serial touchscreens" 96 select SERIO 97 help 98 Say Y here if you have a MicroTouch (3M) serial touchscreen connected to 99 your system. 100 101 If unsure, say N. 102 103 To compile this driver as a module, choose M here: the 104 module will be called mtouch. 105 106config TOUCHSCREEN_MK712 107 tristate "ICS MicroClock MK712 touchscreen" 108 help 109 Say Y here if you have the ICS MicroClock MK712 touchscreen 110 controller chip in your system. 111 112 If unsure, say N. 113 114 To compile this driver as a module, choose M here: the 115 module will be called mk712. 116 117config TOUCHSCREEN_HP600 118 tristate "HP Jornada 6xx touchscreen" 119 depends on SH_HP6XX && SH_ADC 120 help 121 Say Y here if you have a HP Jornada 620/660/680/690 and want to 122 support the built-in touchscreen. 123 124 To compile this driver as a module, choose M here: the 125 module will be called hp680_ts_input. 126 127config TOUCHSCREEN_HP7XX 128 tristate "HP Jornada 7xx touchscreen" 129 depends on SA1100_JORNADA720_SSP 130 help 131 Say Y here if you have a HP Jornada 710/720/728 and want 132 to support the built-in touchscreen. 133 134 To compile this driver as a module, choose M here: the 135 module will be called jornada720_ts. 136 137config TOUCHSCREEN_PENMOUNT 138 tristate "Penmount serial touchscreen" 139 select SERIO 140 help 141 Say Y here if you have a Penmount serial touchscreen connected to 142 your system. 143 144 If unsure, say N. 145 146 To compile this driver as a module, choose M here: the 147 module will be called penmount. 148 149config TOUCHSCREEN_TOUCHRIGHT 150 tristate "Touchright serial touchscreen" 151 select SERIO 152 help 153 Say Y here if you have a Touchright serial touchscreen connected to 154 your system. 155 156 If unsure, say N. 157 158 To compile this driver as a module, choose M here: the 159 module will be called touchright. 160 161config TOUCHSCREEN_TOUCHWIN 162 tristate "Touchwin serial touchscreen" 163 select SERIO 164 help 165 Say Y here if you have a Touchwin serial touchscreen connected to 166 your system. 167 168 If unsure, say N. 169 170 To compile this driver as a module, choose M here: the 171 module will be called touchwin. 172 173config TOUCHSCREEN_UCB1400 174 tristate "Philips UCB1400 touchscreen" 175 select AC97_BUS 176 help 177 This enables support for the Philips UCB1400 touchscreen interface. 178 The UCB1400 is an AC97 audio codec. The touchscreen interface 179 will be initialized only after the ALSA subsystem has been 180 brought up and the UCB1400 detected. You therefore have to 181 configure ALSA support as well (either built-in or modular, 182 independently of whether this driver is itself built-in or 183 modular) for this driver to work. 184 185 To compile this driver as a module, choose M here: the 186 module will be called ucb1400_ts. 187 188config TOUCHSCREEN_WM97XX 189 tristate "Support for WM97xx AC97 touchscreen controllers" 190 depends on AC97_BUS 191 help 192 Say Y here if you have a Wolfson Microelectronics WM97xx 193 touchscreen connected to your system. Note that this option 194 only enables core driver, you will also need to select 195 support for appropriate chip below. 196 197 If unsure, say N. 198 199 To compile this driver as a module, choose M here: the 200 module will be called wm97xx-ts. 201 202config TOUCHSCREEN_USB_COMPOSITE 203 tristate "USB Touchscreen Driver" 204 depends on USB_ARCH_HAS_HCD 205 select USB 206 help 207 USB Touchscreen driver for: 208 - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700) 209 - PanJit TouchSet USB 210 - 3M MicroTouch USB (EX II series) 211 - ITM 212 - some other eTurboTouch 213 - Gunze AHL61 214 - DMC TSC-10/25 215 - IRTOUCHSYSTEMS/UNITOP 216 - IdealTEK URTC1000 217 - GoTop Super_Q2/GogoPen/PenPower tablets 218 219 Have a look at <http://linux.chapter7.ch/touchkit/> for 220 a usage description and the required user-space stuff. 221 222 To compile this driver as a module, choose M here: the 223 module will be called usbtouchscreen. 224 225config TOUCHSCREEN_USB_EGALAX 226 default y 227 bool "eGalax, eTurboTouch CT-410/510/700 device support" if EMBEDDED 228 depends on TOUCHSCREEN_USB_COMPOSITE 229 230config TOUCHSCREEN_USB_PANJIT 231 default y 232 bool "PanJit device support" if EMBEDDED 233 depends on TOUCHSCREEN_USB_COMPOSITE 234 235config TOUCHSCREEN_USB_3M 236 default y 237 bool "3M/Microtouch EX II series device support" if EMBEDDED 238 depends on TOUCHSCREEN_USB_COMPOSITE 239 240config TOUCHSCREEN_USB_ITM 241 default y 242 bool "ITM device support" if EMBEDDED 243 depends on TOUCHSCREEN_USB_COMPOSITE 244 245config TOUCHSCREEN_USB_ETURBO 246 default y 247 bool "eTurboTouch (non-eGalax compatible) device support" if EMBEDDED 248 depends on TOUCHSCREEN_USB_COMPOSITE 249 250config TOUCHSCREEN_USB_GUNZE 251 default y 252 bool "Gunze AHL61 device support" if EMBEDDED 253 depends on TOUCHSCREEN_USB_COMPOSITE 254 255config TOUCHSCREEN_USB_DMC_TSC10 256 default y 257 bool "DMC TSC-10/25 device support" if EMBEDDED 258 depends on TOUCHSCREEN_USB_COMPOSITE 259 260config TOUCHSCREEN_USB_IRTOUCH 261 default y 262 bool "IRTOUCHSYSTEMS/UNITOP device support" if EMBEDDED 263 depends on TOUCHSCREEN_USB_COMPOSITE 264 265config TOUCHSCREEN_USB_IDEALTEK 266 default y 267 bool "IdealTEK URTC1000 device support" if EMBEDDED 268 depends on TOUCHSCREEN_USB_COMPOSITE 269 270config TOUCHSCREEN_USB_GENERAL_TOUCH 271 default y 272 bool "GeneralTouch Touchscreen device support" if EMBEDDED 273 depends on TOUCHSCREEN_USB_COMPOSITE 274 275config TOUCHSCREEN_USB_GOTOP 276 default y 277 bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EMBEDDED 278 depends on TOUCHSCREEN_USB_COMPOSITE 279 280endif 281