xref: /linux/drivers/input/touchscreen/Kconfig (revision c4c0c56a7a85ed5725786219e4fbca7e840b1531) 
1#
2# Touchscreen driver configuration
3#
4menuconfig INPUT_TOUCHSCREEN
5	bool "Touchscreens"
6	help
7	  Say Y here, and a list of supported touchscreens will be displayed.
8	  This option doesn't affect the kernel.
9
10	  If unsure, say Y.
11
12if INPUT_TOUCHSCREEN
13
14config TOUCHSCREEN_ADS7846
15	tristate "ADS7846/TSC2046 and ADS7843 based touchscreens"
16	depends on SPI_MASTER
17	depends on HWMON = n || HWMON
18	help
19	  Say Y here if you have a touchscreen interface using the
20	  ADS7846/TSC2046 or ADS7843 controller, and your board-specific
21	  setup code includes that in its table of SPI devices.
22
23	  If HWMON is selected, and the driver is told the reference voltage
24	  on your board, you will also get hwmon interfaces for the voltage
25	  (and on ads7846/tsc2046, temperature) sensors of this chip.
26
27	  If unsure, say N (but it's safe to say "Y").
28
29	  To compile this driver as a module, choose M here: the
30	  module will be called ads7846.
31
32config TOUCHSCREEN_BITSY
33	tristate "Compaq iPAQ H3600 (Bitsy) touchscreen"
34	depends on SA1100_BITSY
35	select SERIO
36	help
37	  Say Y here if you have the h3600 (Bitsy) touchscreen.
38
39	  If unsure, say N.
40
41	  To compile this driver as a module, choose M here: the
42	  module will be called h3600_ts_input.
43
44config TOUCHSCREEN_CORGI
45	tristate "SharpSL (Corgi and Spitz series) touchscreen driver"
46	depends on PXA_SHARPSL
47	default y
48	help
49	  Say Y here to enable the driver for the touchscreen on the
50	  Sharp SL-C7xx and SL-Cxx00 series of PDAs.
51
52	  If unsure, say N.
53
54	  To compile this driver as a module, choose M here: the
55	  module will be called corgi_ts.
56
57config TOUCHSCREEN_FUJITSU
58	tristate "Fujitsu serial touchscreen"
59	select SERIO
60	help
61	  Say Y here if you have the Fujitsu touchscreen (such as one
62	  installed in Lifebook P series laptop) connected to your
63	  system.
64
65	  If unsure, say N.
66
67	  To compile this driver as a module, choose M here: the
68	  module will be called fujitsu-ts.
69
70config TOUCHSCREEN_GUNZE
71	tristate "Gunze AHL-51S touchscreen"
72	select SERIO
73	help
74	  Say Y here if you have the Gunze AHL-51 touchscreen connected to
75	  your system.
76
77	  If unsure, say N.
78
79	  To compile this driver as a module, choose M here: the
80	  module will be called gunze.
81
82config TOUCHSCREEN_ELO
83	tristate "Elo serial touchscreens"
84	select SERIO
85	help
86	  Say Y here if you have an Elo serial touchscreen connected to
87	  your system.
88
89	  If unsure, say N.
90
91	  To compile this driver as a module, choose M here: the
92	  module will be called elo.
93
94config TOUCHSCREEN_MTOUCH
95	tristate "MicroTouch serial touchscreens"
96	select SERIO
97	help
98	  Say Y here if you have a MicroTouch (3M) serial touchscreen connected to
99	  your system.
100
101	  If unsure, say N.
102
103	  To compile this driver as a module, choose M here: the
104	  module will be called mtouch.
105
106config TOUCHSCREEN_INEXIO
107	tristate "iNexio serial touchscreens"
108	select SERIO
109	help
110	  Say Y here if you have an iNexio serial touchscreen connected to
111	  your system.
112
113	  If unsure, say N.
114
115	  To compile this driver as a module, choose M here: the
116	  module will be called inexio.
117
118config TOUCHSCREEN_MK712
119	tristate "ICS MicroClock MK712 touchscreen"
120	help
121	  Say Y here if you have the ICS MicroClock MK712 touchscreen
122	  controller chip in your system.
123
124	  If unsure, say N.
125
126	  To compile this driver as a module, choose M here: the
127	  module will be called mk712.
128
129config TOUCHSCREEN_HP600
130	tristate "HP Jornada 6xx touchscreen"
131	depends on SH_HP6XX && SH_ADC
132	help
133	  Say Y here if you have a HP Jornada 620/660/680/690 and want to
134          support the built-in touchscreen.
135
136	  To compile this driver as a module, choose M here: the
137	  module will be called hp680_ts_input.
138
139config TOUCHSCREEN_HP7XX
140	tristate "HP Jornada 7xx touchscreen"
141	depends on SA1100_JORNADA720_SSP
142	help
143	  Say Y here if you have a HP Jornada 710/720/728 and want
144	  to support the built-in touchscreen.
145
146	  To compile this driver as a module, choose M here: the
147	  module will be called jornada720_ts.
148
149config TOUCHSCREEN_HTCPEN
150	tristate "HTC Shift X9500 touchscreen"
151	depends on ISA
152	help
153	  Say Y here if you have an HTC Shift UMPC also known as HTC X9500
154	  Clio / Shangrila and want to support the built-in touchscreen.
155
156	  If unsure, say N.
157
158	  To compile this driver as a module, choose M here: the
159	  module will be called htcpen.
160
161config TOUCHSCREEN_PENMOUNT
162	tristate "Penmount serial touchscreen"
163	select SERIO
164	help
165	  Say Y here if you have a Penmount serial touchscreen connected to
166	  your system.
167
168	  If unsure, say N.
169
170	  To compile this driver as a module, choose M here: the
171	  module will be called penmount.
172
173config TOUCHSCREEN_MIGOR
174	tristate "Renesas MIGO-R touchscreen"
175	depends on SH_MIGOR && I2C
176	help
177	  Say Y here to enable MIGO-R touchscreen support.
178
179	  If unsure, say N.
180
181	  To compile this driver as a module, choose M here: the
182	  module will be called migor_ts.
183
184config TOUCHSCREEN_TOUCHRIGHT
185	tristate "Touchright serial touchscreen"
186	select SERIO
187	help
188	  Say Y here if you have a Touchright serial touchscreen connected to
189	  your system.
190
191	  If unsure, say N.
192
193	  To compile this driver as a module, choose M here: the
194	  module will be called touchright.
195
196config TOUCHSCREEN_TOUCHWIN
197	tristate "Touchwin serial touchscreen"
198	select SERIO
199	help
200	  Say Y here if you have a Touchwin serial touchscreen connected to
201	  your system.
202
203	  If unsure, say N.
204
205	  To compile this driver as a module, choose M here: the
206	  module will be called touchwin.
207
208config TOUCHSCREEN_ATMEL_TSADCC
209	tristate "Atmel Touchscreen Interface"
210	depends on ARCH_AT91SAM9RL
211	help
212	  Say Y here if you have a 4-wire touchscreen connected to the
213          ADC Controller on your Atmel SoC (such as the AT91SAM9RL).
214
215	  If unsure, say N.
216
217	  To compile this driver as a module, choose M here: the
218	  module will be called atmel_tsadcc.
219
220config TOUCHSCREEN_UCB1400
221	tristate "Philips UCB1400 touchscreen"
222	select AC97_BUS
223	help
224	  This enables support for the Philips UCB1400 touchscreen interface.
225	  The UCB1400 is an AC97 audio codec.  The touchscreen interface
226	  will be initialized only after the ALSA subsystem has been
227	  brought up and the UCB1400 detected.  You therefore have to
228	  configure ALSA support as well (either built-in or modular,
229	  independently of whether this driver is itself built-in or
230	  modular) for this driver to work.
231
232	  To compile this driver as a module, choose M here: the
233	  module will be called ucb1400_ts.
234
235config TOUCHSCREEN_WM97XX
236	tristate "Support for WM97xx AC97 touchscreen controllers"
237	depends on AC97_BUS
238	help
239	  Say Y here if you have a Wolfson Microelectronics WM97xx
240	  touchscreen connected to your system. Note that this option
241	  only enables core driver, you will also need to select
242	  support for appropriate chip below.
243
244	  If unsure, say N.
245
246	  To compile this driver as a module, choose M here: the
247	  module will be called wm97xx-ts.
248
249config TOUCHSCREEN_WM9705
250	bool "WM9705 Touchscreen interface support"
251	depends on TOUCHSCREEN_WM97XX
252	help
253	  Say Y here if you have a Wolfson Microelectronics WM9705
254	  touchscreen controller connected to your system.
255
256	  If unsure, say N.
257
258config TOUCHSCREEN_WM9712
259	bool "WM9712 Touchscreen interface support"
260	depends on TOUCHSCREEN_WM97XX
261	help
262	  Say Y here if you have a Wolfson Microelectronics WM9712
263	  touchscreen controller connected to your system.
264
265	  If unsure, say N.
266
267config TOUCHSCREEN_WM9713
268	bool "WM9713 Touchscreen interface support"
269	depends on TOUCHSCREEN_WM97XX
270	help
271	  Say Y here if you have a Wolfson Microelectronics WM9713 touchscreen
272	  controller connected to your system.
273
274	  If unsure, say N.
275
276config TOUCHSCREEN_WM97XX_MAINSTONE
277	tristate "WM97xx Mainstone accelerated touch"
278	depends on TOUCHSCREEN_WM97XX && ARCH_PXA
279	help
280	  Say Y here for support for streaming mode with WM97xx touchscreens
281	  on Mainstone systems.
282
283	  If unsure, say N.
284
285	  To compile this driver as a module, choose M here: the
286	  module will be called mainstone-wm97xx.
287
288config TOUCHSCREEN_USB_COMPOSITE
289	tristate "USB Touchscreen Driver"
290	depends on USB_ARCH_HAS_HCD
291	select USB
292	help
293	  USB Touchscreen driver for:
294	  - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700)
295	  - PanJit TouchSet USB
296	  - 3M MicroTouch USB (EX II series)
297	  - ITM
298	  - some other eTurboTouch
299	  - Gunze AHL61
300	  - DMC TSC-10/25
301	  - IRTOUCHSYSTEMS/UNITOP
302	  - IdealTEK URTC1000
303	  - GoTop Super_Q2/GogoPen/PenPower tablets
304
305	  Have a look at <http://linux.chapter7.ch/touchkit/> for
306	  a usage description and the required user-space stuff.
307
308	  To compile this driver as a module, choose M here: the
309	  module will be called usbtouchscreen.
310
311config TOUCHSCREEN_USB_EGALAX
312	default y
313	bool "eGalax, eTurboTouch CT-410/510/700 device support" if EMBEDDED
314	depends on TOUCHSCREEN_USB_COMPOSITE
315
316config TOUCHSCREEN_USB_PANJIT
317	default y
318	bool "PanJit device support" if EMBEDDED
319	depends on TOUCHSCREEN_USB_COMPOSITE
320
321config TOUCHSCREEN_USB_3M
322	default y
323	bool "3M/Microtouch EX II series device support" if EMBEDDED
324	depends on TOUCHSCREEN_USB_COMPOSITE
325
326config TOUCHSCREEN_USB_ITM
327	default y
328	bool "ITM device support" if EMBEDDED
329	depends on TOUCHSCREEN_USB_COMPOSITE
330
331config TOUCHSCREEN_USB_ETURBO
332	default y
333	bool "eTurboTouch (non-eGalax compatible) device support" if EMBEDDED
334	depends on TOUCHSCREEN_USB_COMPOSITE
335
336config TOUCHSCREEN_USB_GUNZE
337	default y
338	bool "Gunze AHL61 device support" if EMBEDDED
339	depends on TOUCHSCREEN_USB_COMPOSITE
340
341config TOUCHSCREEN_USB_DMC_TSC10
342	default y
343	bool "DMC TSC-10/25 device support" if EMBEDDED
344	depends on TOUCHSCREEN_USB_COMPOSITE
345
346config TOUCHSCREEN_USB_IRTOUCH
347	default y
348	bool "IRTOUCHSYSTEMS/UNITOP device support" if EMBEDDED
349	depends on TOUCHSCREEN_USB_COMPOSITE
350
351config TOUCHSCREEN_USB_IDEALTEK
352	default y
353	bool "IdealTEK URTC1000 device support" if EMBEDDED
354	depends on TOUCHSCREEN_USB_COMPOSITE
355
356config TOUCHSCREEN_USB_GENERAL_TOUCH
357	default y
358	bool "GeneralTouch Touchscreen device support" if EMBEDDED
359	depends on TOUCHSCREEN_USB_COMPOSITE
360
361config TOUCHSCREEN_USB_GOTOP
362	default y
363	bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EMBEDDED
364	depends on TOUCHSCREEN_USB_COMPOSITE
365
366config TOUCHSCREEN_TOUCHIT213
367	tristate "Sahara TouchIT-213 touchscreen"
368	select SERIO
369	help
370	  Say Y here if you have a Sahara TouchIT-213 Tablet PC.
371
372	  If unsure, say N.
373
374	  To compile this driver as a module, choose M here: the
375	  module will be called touchit213.
376
377endif
378