1# 2# Touchscreen driver configuration 3# 4menuconfig INPUT_TOUCHSCREEN 5 bool "Touchscreens" 6 help 7 Say Y here, and a list of supported touchscreens will be displayed. 8 This option doesn't affect the kernel. 9 10 If unsure, say Y. 11 12if INPUT_TOUCHSCREEN 13 14config TOUCHSCREEN_ADS7846 15 tristate "ADS7846/TSC2046 and ADS7843 based touchscreens" 16 depends on SPI_MASTER 17 depends on HWMON = n || HWMON 18 help 19 Say Y here if you have a touchscreen interface using the 20 ADS7846/TSC2046 or ADS7843 controller, and your board-specific 21 setup code includes that in its table of SPI devices. 22 23 If HWMON is selected, and the driver is told the reference voltage 24 on your board, you will also get hwmon interfaces for the voltage 25 (and on ads7846/tsc2046, temperature) sensors of this chip. 26 27 If unsure, say N (but it's safe to say "Y"). 28 29 To compile this driver as a module, choose M here: the 30 module will be called ads7846. 31 32config TOUCHSCREEN_BITSY 33 tristate "Compaq iPAQ H3600 (Bitsy) touchscreen" 34 depends on SA1100_BITSY 35 select SERIO 36 help 37 Say Y here if you have the h3600 (Bitsy) touchscreen. 38 39 If unsure, say N. 40 41 To compile this driver as a module, choose M here: the 42 module will be called h3600_ts_input. 43 44config TOUCHSCREEN_CORGI 45 tristate "SharpSL (Corgi and Spitz series) touchscreen driver" 46 depends on PXA_SHARPSL 47 default y 48 help 49 Say Y here to enable the driver for the touchscreen on the 50 Sharp SL-C7xx and SL-Cxx00 series of PDAs. 51 52 If unsure, say N. 53 54 To compile this driver as a module, choose M here: the 55 module will be called corgi_ts. 56 57config TOUCHSCREEN_FUJITSU 58 tristate "Fujitsu serial touchscreen" 59 select SERIO 60 help 61 Say Y here if you have the Fujitsu touchscreen (such as one 62 installed in Lifebook P series laptop) connected to your 63 system. 64 65 If unsure, say N. 66 67 To compile this driver as a module, choose M here: the 68 module will be called fujitsu-ts. 69 70config TOUCHSCREEN_GUNZE 71 tristate "Gunze AHL-51S touchscreen" 72 select SERIO 73 help 74 Say Y here if you have the Gunze AHL-51 touchscreen connected to 75 your system. 76 77 If unsure, say N. 78 79 To compile this driver as a module, choose M here: the 80 module will be called gunze. 81 82config TOUCHSCREEN_ELO 83 tristate "Elo serial touchscreens" 84 select SERIO 85 help 86 Say Y here if you have an Elo serial touchscreen connected to 87 your system. 88 89 If unsure, say N. 90 91 To compile this driver as a module, choose M here: the 92 module will be called elo. 93 94config TOUCHSCREEN_MTOUCH 95 tristate "MicroTouch serial touchscreens" 96 select SERIO 97 help 98 Say Y here if you have a MicroTouch (3M) serial touchscreen connected to 99 your system. 100 101 If unsure, say N. 102 103 To compile this driver as a module, choose M here: the 104 module will be called mtouch. 105 106config TOUCHSCREEN_MK712 107 tristate "ICS MicroClock MK712 touchscreen" 108 help 109 Say Y here if you have the ICS MicroClock MK712 touchscreen 110 controller chip in your system. 111 112 If unsure, say N. 113 114 To compile this driver as a module, choose M here: the 115 module will be called mk712. 116 117config TOUCHSCREEN_HP600 118 tristate "HP Jornada 680/690 touchscreen" 119 depends on SH_HP6XX && SH_ADC 120 help 121 Say Y here if you have a HP Jornada 680 or 690 and want to 122 support the built-in touchscreen. 123 124 If unsure, say N. 125 126 To compile this driver as a module, choose M here: the 127 module will be called hp680_ts_input. 128 129config TOUCHSCREEN_HP7XX 130 tristate "HP Jornada 710/720/728 touchscreen" 131 depends on SA1100_JORNADA720_SSP 132 help 133 Say Y here if you have a HP Jornada 710/720/728 and want 134 to support the built-in touchscreen. 135 136 To compile this driver as a module, choose M here: the 137 module will be called jornada720_ts. 138 139config TOUCHSCREEN_PENMOUNT 140 tristate "Penmount serial touchscreen" 141 select SERIO 142 help 143 Say Y here if you have a Penmount serial touchscreen connected to 144 your system. 145 146 If unsure, say N. 147 148 To compile this driver as a module, choose M here: the 149 module will be called penmount. 150 151config TOUCHSCREEN_TOUCHRIGHT 152 tristate "Touchright serial touchscreen" 153 select SERIO 154 help 155 Say Y here if you have a Touchright serial touchscreen connected to 156 your system. 157 158 If unsure, say N. 159 160 To compile this driver as a module, choose M here: the 161 module will be called touchright. 162 163config TOUCHSCREEN_TOUCHWIN 164 tristate "Touchwin serial touchscreen" 165 select SERIO 166 help 167 Say Y here if you have a Touchwin serial touchscreen connected to 168 your system. 169 170 If unsure, say N. 171 172 To compile this driver as a module, choose M here: the 173 module will be called touchwin. 174 175config TOUCHSCREEN_UCB1400 176 tristate "Philips UCB1400 touchscreen" 177 select AC97_BUS 178 help 179 This enables support for the Philips UCB1400 touchscreen interface. 180 The UCB1400 is an AC97 audio codec. The touchscreen interface 181 will be initialized only after the ALSA subsystem has been 182 brought up and the UCB1400 detected. You therefore have to 183 configure ALSA support as well (either built-in or modular, 184 independently of whether this driver is itself built-in or 185 modular) for this driver to work. 186 187 To compile this driver as a module, choose M here: the 188 module will be called ucb1400_ts. 189 190config TOUCHSCREEN_USB_COMPOSITE 191 tristate "USB Touchscreen Driver" 192 depends on USB_ARCH_HAS_HCD 193 select USB 194 help 195 USB Touchscreen driver for: 196 - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700) 197 - PanJit TouchSet USB 198 - 3M MicroTouch USB (EX II series) 199 - ITM 200 - some other eTurboTouch 201 - Gunze AHL61 202 - DMC TSC-10/25 203 - IRTOUCHSYSTEMS/UNITOP 204 - IdealTEK URTC1000 205 - GoTop Super_Q2/GogoPen/PenPower tablets 206 207 Have a look at <http://linux.chapter7.ch/touchkit/> for 208 a usage description and the required user-space stuff. 209 210 To compile this driver as a module, choose M here: the 211 module will be called usbtouchscreen. 212 213config TOUCHSCREEN_USB_EGALAX 214 default y 215 bool "eGalax, eTurboTouch CT-410/510/700 device support" if EMBEDDED 216 depends on TOUCHSCREEN_USB_COMPOSITE 217 218config TOUCHSCREEN_USB_PANJIT 219 default y 220 bool "PanJit device support" if EMBEDDED 221 depends on TOUCHSCREEN_USB_COMPOSITE 222 223config TOUCHSCREEN_USB_3M 224 default y 225 bool "3M/Microtouch EX II series device support" if EMBEDDED 226 depends on TOUCHSCREEN_USB_COMPOSITE 227 228config TOUCHSCREEN_USB_ITM 229 default y 230 bool "ITM device support" if EMBEDDED 231 depends on TOUCHSCREEN_USB_COMPOSITE 232 233config TOUCHSCREEN_USB_ETURBO 234 default y 235 bool "eTurboTouch (non-eGalax compatible) device support" if EMBEDDED 236 depends on TOUCHSCREEN_USB_COMPOSITE 237 238config TOUCHSCREEN_USB_GUNZE 239 default y 240 bool "Gunze AHL61 device support" if EMBEDDED 241 depends on TOUCHSCREEN_USB_COMPOSITE 242 243config TOUCHSCREEN_USB_DMC_TSC10 244 default y 245 bool "DMC TSC-10/25 device support" if EMBEDDED 246 depends on TOUCHSCREEN_USB_COMPOSITE 247 248config TOUCHSCREEN_USB_IRTOUCH 249 default y 250 bool "IRTOUCHSYSTEMS/UNITOP device support" if EMBEDDED 251 depends on TOUCHSCREEN_USB_COMPOSITE 252 253config TOUCHSCREEN_USB_IDEALTEK 254 default y 255 bool "IdealTEK URTC1000 device support" if EMBEDDED 256 depends on TOUCHSCREEN_USB_COMPOSITE 257 258config TOUCHSCREEN_USB_GENERAL_TOUCH 259 default y 260 bool "GeneralTouch Touchscreen device support" if EMBEDDED 261 depends on TOUCHSCREEN_USB_COMPOSITE 262 263config TOUCHSCREEN_USB_GOTOP 264 default y 265 bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EMBEDDED 266 depends on TOUCHSCREEN_USB_COMPOSITE 267 268endif 269