1 /* 2 * HP i8042-based System Device Controller driver. 3 * 4 * Copyright (c) 2001 Brian S. Julin 5 * All rights reserved. 6 * 7 * Redistribution and use in source and binary forms, with or without 8 * modification, are permitted provided that the following conditions 9 * are met: 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions, and the following disclaimer, 12 * without modification. 13 * 2. The name of the author may not be used to endorse or promote products 14 * derived from this software without specific prior written permission. 15 * 16 * Alternatively, this software may be distributed under the terms of the 17 * GNU General Public License ("GPL"). 18 * 19 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 20 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 21 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 22 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR 23 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 24 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 25 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 26 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 27 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 28 * 29 * References: 30 * System Device Controller Microprocessor Firmware Theory of Operation 31 * for Part Number 1820-4784 Revision B. Dwg No. A-1820-4784-2 32 * Helge Deller's original hilkbd.c port for PA-RISC. 33 * 34 * 35 * Driver theory of operation: 36 * 37 * hp_sdc_put does all writing to the SDC. ISR can run on a different 38 * CPU than hp_sdc_put, but only one CPU runs hp_sdc_put at a time 39 * (it cannot really benefit from SMP anyway.) A tasket fit this perfectly. 40 * 41 * All data coming back from the SDC is sent via interrupt and can be read 42 * fully in the ISR, so there are no latency/throughput problems there. 43 * The problem is with output, due to the slow clock speed of the SDC 44 * compared to the CPU. This should not be too horrible most of the time, 45 * but if used with HIL devices that support the multibyte transfer command, 46 * keeping outbound throughput flowing at the 6500KBps that the HIL is 47 * capable of is more than can be done at HZ=100. 48 * 49 * Busy polling for IBF clear wastes CPU cycles and bus cycles. hp_sdc.ibf 50 * is set to 0 when the IBF flag in the status register has cleared. ISR 51 * may do this, and may also access the parts of queued transactions related 52 * to reading data back from the SDC, but otherwise will not touch the 53 * hp_sdc state. Whenever a register is written hp_sdc.ibf is set to 1. 54 * 55 * The i8042 write index and the values in the 4-byte input buffer 56 * starting at 0x70 are kept track of in hp_sdc.wi, and .r7[], respectively, 57 * to minimize the amount of IO needed to the SDC. However these values 58 * do not need to be locked since they are only ever accessed by hp_sdc_put. 59 * 60 * A timer task schedules the tasklet once per second just to make 61 * sure it doesn't freeze up and to allow for bad reads to time out. 62 */ 63 64 #include <linux/hp_sdc.h> 65 #include <linux/errno.h> 66 #include <linux/init.h> 67 #include <linux/module.h> 68 #include <linux/ioport.h> 69 #include <linux/time.h> 70 #include <linux/semaphore.h> 71 #include <linux/slab.h> 72 #include <linux/hil.h> 73 #include <asm/io.h> 74 75 /* Machine-specific abstraction */ 76 77 #if defined(__hppa__) 78 # include <asm/parisc-device.h> 79 # define sdc_readb(p) gsc_readb(p) 80 # define sdc_writeb(v,p) gsc_writeb((v),(p)) 81 #elif defined(__mc68000__) 82 #include <linux/uaccess.h> 83 # define sdc_readb(p) in_8(p) 84 # define sdc_writeb(v,p) out_8((p),(v)) 85 #else 86 # error "HIL is not supported on this platform" 87 #endif 88 89 #define PREFIX "HP SDC: " 90 91 MODULE_AUTHOR("Brian S. Julin <bri@calyx.com>"); 92 MODULE_DESCRIPTION("HP i8042-based SDC Driver"); 93 MODULE_LICENSE("Dual BSD/GPL"); 94 95 EXPORT_SYMBOL(hp_sdc_request_timer_irq); 96 EXPORT_SYMBOL(hp_sdc_request_hil_irq); 97 EXPORT_SYMBOL(hp_sdc_request_cooked_irq); 98 99 EXPORT_SYMBOL(hp_sdc_release_timer_irq); 100 EXPORT_SYMBOL(hp_sdc_release_hil_irq); 101 EXPORT_SYMBOL(hp_sdc_release_cooked_irq); 102 103 EXPORT_SYMBOL(__hp_sdc_enqueue_transaction); 104 EXPORT_SYMBOL(hp_sdc_enqueue_transaction); 105 EXPORT_SYMBOL(hp_sdc_dequeue_transaction); 106 107 static bool hp_sdc_disabled; 108 module_param_named(no_hpsdc, hp_sdc_disabled, bool, 0); 109 MODULE_PARM_DESC(no_hpsdc, "Do not enable HP SDC driver."); 110 111 static hp_i8042_sdc hp_sdc; /* All driver state is kept in here. */ 112 113 /*************** primitives for use in any context *********************/ 114 static inline uint8_t hp_sdc_status_in8(void) 115 { 116 uint8_t status; 117 unsigned long flags; 118 119 write_lock_irqsave(&hp_sdc.ibf_lock, flags); 120 status = sdc_readb(hp_sdc.status_io); 121 if (!(status & HP_SDC_STATUS_IBF)) 122 hp_sdc.ibf = 0; 123 write_unlock_irqrestore(&hp_sdc.ibf_lock, flags); 124 125 return status; 126 } 127 128 static inline uint8_t hp_sdc_data_in8(void) 129 { 130 return sdc_readb(hp_sdc.data_io); 131 } 132 133 static inline void hp_sdc_status_out8(uint8_t val) 134 { 135 unsigned long flags; 136 137 write_lock_irqsave(&hp_sdc.ibf_lock, flags); 138 hp_sdc.ibf = 1; 139 if ((val & 0xf0) == 0xe0) 140 hp_sdc.wi = 0xff; 141 sdc_writeb(val, hp_sdc.status_io); 142 write_unlock_irqrestore(&hp_sdc.ibf_lock, flags); 143 } 144 145 static inline void hp_sdc_data_out8(uint8_t val) 146 { 147 unsigned long flags; 148 149 write_lock_irqsave(&hp_sdc.ibf_lock, flags); 150 hp_sdc.ibf = 1; 151 sdc_writeb(val, hp_sdc.data_io); 152 write_unlock_irqrestore(&hp_sdc.ibf_lock, flags); 153 } 154 155 /* Care must be taken to only invoke hp_sdc_spin_ibf when 156 * absolutely needed, or in rarely invoked subroutines. 157 * Not only does it waste CPU cycles, it also wastes bus cycles. 158 */ 159 static inline void hp_sdc_spin_ibf(void) 160 { 161 unsigned long flags; 162 rwlock_t *lock; 163 164 lock = &hp_sdc.ibf_lock; 165 166 read_lock_irqsave(lock, flags); 167 if (!hp_sdc.ibf) { 168 read_unlock_irqrestore(lock, flags); 169 return; 170 } 171 read_unlock(lock); 172 write_lock(lock); 173 while (sdc_readb(hp_sdc.status_io) & HP_SDC_STATUS_IBF) 174 { } 175 hp_sdc.ibf = 0; 176 write_unlock_irqrestore(lock, flags); 177 } 178 179 180 /************************ Interrupt context functions ************************/ 181 static void hp_sdc_take(int irq, void *dev_id, uint8_t status, uint8_t data) 182 { 183 hp_sdc_transaction *curr; 184 185 read_lock(&hp_sdc.rtq_lock); 186 if (hp_sdc.rcurr < 0) { 187 read_unlock(&hp_sdc.rtq_lock); 188 return; 189 } 190 curr = hp_sdc.tq[hp_sdc.rcurr]; 191 read_unlock(&hp_sdc.rtq_lock); 192 193 curr->seq[curr->idx++] = status; 194 curr->seq[curr->idx++] = data; 195 hp_sdc.rqty -= 2; 196 do_gettimeofday(&hp_sdc.rtv); 197 198 if (hp_sdc.rqty <= 0) { 199 /* All data has been gathered. */ 200 if (curr->seq[curr->actidx] & HP_SDC_ACT_SEMAPHORE) 201 if (curr->act.semaphore) 202 up(curr->act.semaphore); 203 204 if (curr->seq[curr->actidx] & HP_SDC_ACT_CALLBACK) 205 if (curr->act.irqhook) 206 curr->act.irqhook(irq, dev_id, status, data); 207 208 curr->actidx = curr->idx; 209 curr->idx++; 210 /* Return control of this transaction */ 211 write_lock(&hp_sdc.rtq_lock); 212 hp_sdc.rcurr = -1; 213 hp_sdc.rqty = 0; 214 write_unlock(&hp_sdc.rtq_lock); 215 tasklet_schedule(&hp_sdc.task); 216 } 217 } 218 219 static irqreturn_t hp_sdc_isr(int irq, void *dev_id) 220 { 221 uint8_t status, data; 222 223 status = hp_sdc_status_in8(); 224 /* Read data unconditionally to advance i8042. */ 225 data = hp_sdc_data_in8(); 226 227 /* For now we are ignoring these until we get the SDC to behave. */ 228 if (((status & 0xf1) == 0x51) && data == 0x82) 229 return IRQ_HANDLED; 230 231 switch (status & HP_SDC_STATUS_IRQMASK) { 232 case 0: /* This case is not documented. */ 233 break; 234 235 case HP_SDC_STATUS_USERTIMER: 236 case HP_SDC_STATUS_PERIODIC: 237 case HP_SDC_STATUS_TIMER: 238 read_lock(&hp_sdc.hook_lock); 239 if (hp_sdc.timer != NULL) 240 hp_sdc.timer(irq, dev_id, status, data); 241 read_unlock(&hp_sdc.hook_lock); 242 break; 243 244 case HP_SDC_STATUS_REG: 245 hp_sdc_take(irq, dev_id, status, data); 246 break; 247 248 case HP_SDC_STATUS_HILCMD: 249 case HP_SDC_STATUS_HILDATA: 250 read_lock(&hp_sdc.hook_lock); 251 if (hp_sdc.hil != NULL) 252 hp_sdc.hil(irq, dev_id, status, data); 253 read_unlock(&hp_sdc.hook_lock); 254 break; 255 256 case HP_SDC_STATUS_PUP: 257 read_lock(&hp_sdc.hook_lock); 258 if (hp_sdc.pup != NULL) 259 hp_sdc.pup(irq, dev_id, status, data); 260 else 261 printk(KERN_INFO PREFIX "HP SDC reports successful PUP.\n"); 262 read_unlock(&hp_sdc.hook_lock); 263 break; 264 265 default: 266 read_lock(&hp_sdc.hook_lock); 267 if (hp_sdc.cooked != NULL) 268 hp_sdc.cooked(irq, dev_id, status, data); 269 read_unlock(&hp_sdc.hook_lock); 270 break; 271 } 272 273 return IRQ_HANDLED; 274 } 275 276 277 static irqreturn_t hp_sdc_nmisr(int irq, void *dev_id) 278 { 279 int status; 280 281 status = hp_sdc_status_in8(); 282 printk(KERN_WARNING PREFIX "NMI !\n"); 283 284 #if 0 285 if (status & HP_SDC_NMISTATUS_FHS) { 286 read_lock(&hp_sdc.hook_lock); 287 if (hp_sdc.timer != NULL) 288 hp_sdc.timer(irq, dev_id, status, 0); 289 read_unlock(&hp_sdc.hook_lock); 290 } else { 291 /* TODO: pass this on to the HIL handler, or do SAK here? */ 292 printk(KERN_WARNING PREFIX "HIL NMI\n"); 293 } 294 #endif 295 296 return IRQ_HANDLED; 297 } 298 299 300 /***************** Kernel (tasklet) context functions ****************/ 301 302 unsigned long hp_sdc_put(void); 303 304 static void hp_sdc_tasklet(unsigned long foo) 305 { 306 write_lock_irq(&hp_sdc.rtq_lock); 307 308 if (hp_sdc.rcurr >= 0) { 309 struct timeval tv; 310 311 do_gettimeofday(&tv); 312 if (tv.tv_sec > hp_sdc.rtv.tv_sec) 313 tv.tv_usec += USEC_PER_SEC; 314 315 if (tv.tv_usec - hp_sdc.rtv.tv_usec > HP_SDC_MAX_REG_DELAY) { 316 hp_sdc_transaction *curr; 317 uint8_t tmp; 318 319 curr = hp_sdc.tq[hp_sdc.rcurr]; 320 /* If this turns out to be a normal failure mode 321 * we'll need to figure out a way to communicate 322 * it back to the application. and be less verbose. 323 */ 324 printk(KERN_WARNING PREFIX "read timeout (%ius)!\n", 325 (int)(tv.tv_usec - hp_sdc.rtv.tv_usec)); 326 curr->idx += hp_sdc.rqty; 327 hp_sdc.rqty = 0; 328 tmp = curr->seq[curr->actidx]; 329 curr->seq[curr->actidx] |= HP_SDC_ACT_DEAD; 330 if (tmp & HP_SDC_ACT_SEMAPHORE) 331 if (curr->act.semaphore) 332 up(curr->act.semaphore); 333 334 if (tmp & HP_SDC_ACT_CALLBACK) { 335 /* Note this means that irqhooks may be called 336 * in tasklet/bh context. 337 */ 338 if (curr->act.irqhook) 339 curr->act.irqhook(0, NULL, 0, 0); 340 } 341 342 curr->actidx = curr->idx; 343 curr->idx++; 344 hp_sdc.rcurr = -1; 345 } 346 } 347 write_unlock_irq(&hp_sdc.rtq_lock); 348 hp_sdc_put(); 349 } 350 351 unsigned long hp_sdc_put(void) 352 { 353 hp_sdc_transaction *curr; 354 uint8_t act; 355 int idx, curridx; 356 357 int limit = 0; 358 359 write_lock(&hp_sdc.lock); 360 361 /* If i8042 buffers are full, we cannot do anything that 362 requires output, so we skip to the administrativa. */ 363 if (hp_sdc.ibf) { 364 hp_sdc_status_in8(); 365 if (hp_sdc.ibf) 366 goto finish; 367 } 368 369 anew: 370 /* See if we are in the middle of a sequence. */ 371 if (hp_sdc.wcurr < 0) 372 hp_sdc.wcurr = 0; 373 read_lock_irq(&hp_sdc.rtq_lock); 374 if (hp_sdc.rcurr == hp_sdc.wcurr) 375 hp_sdc.wcurr++; 376 read_unlock_irq(&hp_sdc.rtq_lock); 377 if (hp_sdc.wcurr >= HP_SDC_QUEUE_LEN) 378 hp_sdc.wcurr = 0; 379 curridx = hp_sdc.wcurr; 380 381 if (hp_sdc.tq[curridx] != NULL) 382 goto start; 383 384 while (++curridx != hp_sdc.wcurr) { 385 if (curridx >= HP_SDC_QUEUE_LEN) { 386 curridx = -1; /* Wrap to top */ 387 continue; 388 } 389 read_lock_irq(&hp_sdc.rtq_lock); 390 if (hp_sdc.rcurr == curridx) { 391 read_unlock_irq(&hp_sdc.rtq_lock); 392 continue; 393 } 394 read_unlock_irq(&hp_sdc.rtq_lock); 395 if (hp_sdc.tq[curridx] != NULL) 396 break; /* Found one. */ 397 } 398 if (curridx == hp_sdc.wcurr) { /* There's nothing queued to do. */ 399 curridx = -1; 400 } 401 hp_sdc.wcurr = curridx; 402 403 start: 404 405 /* Check to see if the interrupt mask needs to be set. */ 406 if (hp_sdc.set_im) { 407 hp_sdc_status_out8(hp_sdc.im | HP_SDC_CMD_SET_IM); 408 hp_sdc.set_im = 0; 409 goto finish; 410 } 411 412 if (hp_sdc.wcurr == -1) 413 goto done; 414 415 curr = hp_sdc.tq[curridx]; 416 idx = curr->actidx; 417 418 if (curr->actidx >= curr->endidx) { 419 hp_sdc.tq[curridx] = NULL; 420 /* Interleave outbound data between the transactions. */ 421 hp_sdc.wcurr++; 422 if (hp_sdc.wcurr >= HP_SDC_QUEUE_LEN) 423 hp_sdc.wcurr = 0; 424 goto finish; 425 } 426 427 act = curr->seq[idx]; 428 idx++; 429 430 if (curr->idx >= curr->endidx) { 431 if (act & HP_SDC_ACT_DEALLOC) 432 kfree(curr); 433 hp_sdc.tq[curridx] = NULL; 434 /* Interleave outbound data between the transactions. */ 435 hp_sdc.wcurr++; 436 if (hp_sdc.wcurr >= HP_SDC_QUEUE_LEN) 437 hp_sdc.wcurr = 0; 438 goto finish; 439 } 440 441 while (act & HP_SDC_ACT_PRECMD) { 442 if (curr->idx != idx) { 443 idx++; 444 act &= ~HP_SDC_ACT_PRECMD; 445 break; 446 } 447 hp_sdc_status_out8(curr->seq[idx]); 448 curr->idx++; 449 /* act finished? */ 450 if ((act & HP_SDC_ACT_DURING) == HP_SDC_ACT_PRECMD) 451 goto actdone; 452 /* skip quantity field if data-out sequence follows. */ 453 if (act & HP_SDC_ACT_DATAOUT) 454 curr->idx++; 455 goto finish; 456 } 457 if (act & HP_SDC_ACT_DATAOUT) { 458 int qty; 459 460 qty = curr->seq[idx]; 461 idx++; 462 if (curr->idx - idx < qty) { 463 hp_sdc_data_out8(curr->seq[curr->idx]); 464 curr->idx++; 465 /* act finished? */ 466 if (curr->idx - idx >= qty && 467 (act & HP_SDC_ACT_DURING) == HP_SDC_ACT_DATAOUT) 468 goto actdone; 469 goto finish; 470 } 471 idx += qty; 472 act &= ~HP_SDC_ACT_DATAOUT; 473 } else 474 while (act & HP_SDC_ACT_DATAREG) { 475 int mask; 476 uint8_t w7[4]; 477 478 mask = curr->seq[idx]; 479 if (idx != curr->idx) { 480 idx++; 481 idx += !!(mask & 1); 482 idx += !!(mask & 2); 483 idx += !!(mask & 4); 484 idx += !!(mask & 8); 485 act &= ~HP_SDC_ACT_DATAREG; 486 break; 487 } 488 489 w7[0] = (mask & 1) ? curr->seq[++idx] : hp_sdc.r7[0]; 490 w7[1] = (mask & 2) ? curr->seq[++idx] : hp_sdc.r7[1]; 491 w7[2] = (mask & 4) ? curr->seq[++idx] : hp_sdc.r7[2]; 492 w7[3] = (mask & 8) ? curr->seq[++idx] : hp_sdc.r7[3]; 493 494 if (hp_sdc.wi > 0x73 || hp_sdc.wi < 0x70 || 495 w7[hp_sdc.wi - 0x70] == hp_sdc.r7[hp_sdc.wi - 0x70]) { 496 int i = 0; 497 498 /* Need to point the write index register */ 499 while (i < 4 && w7[i] == hp_sdc.r7[i]) 500 i++; 501 502 if (i < 4) { 503 hp_sdc_status_out8(HP_SDC_CMD_SET_D0 + i); 504 hp_sdc.wi = 0x70 + i; 505 goto finish; 506 } 507 508 idx++; 509 if ((act & HP_SDC_ACT_DURING) == HP_SDC_ACT_DATAREG) 510 goto actdone; 511 512 curr->idx = idx; 513 act &= ~HP_SDC_ACT_DATAREG; 514 break; 515 } 516 517 hp_sdc_data_out8(w7[hp_sdc.wi - 0x70]); 518 hp_sdc.r7[hp_sdc.wi - 0x70] = w7[hp_sdc.wi - 0x70]; 519 hp_sdc.wi++; /* write index register autoincrements */ 520 { 521 int i = 0; 522 523 while ((i < 4) && w7[i] == hp_sdc.r7[i]) 524 i++; 525 if (i >= 4) { 526 curr->idx = idx + 1; 527 if ((act & HP_SDC_ACT_DURING) == 528 HP_SDC_ACT_DATAREG) 529 goto actdone; 530 } 531 } 532 goto finish; 533 } 534 /* We don't go any further in the command if there is a pending read, 535 because we don't want interleaved results. */ 536 read_lock_irq(&hp_sdc.rtq_lock); 537 if (hp_sdc.rcurr >= 0) { 538 read_unlock_irq(&hp_sdc.rtq_lock); 539 goto finish; 540 } 541 read_unlock_irq(&hp_sdc.rtq_lock); 542 543 544 if (act & HP_SDC_ACT_POSTCMD) { 545 uint8_t postcmd; 546 547 /* curr->idx should == idx at this point. */ 548 postcmd = curr->seq[idx]; 549 curr->idx++; 550 if (act & HP_SDC_ACT_DATAIN) { 551 552 /* Start a new read */ 553 hp_sdc.rqty = curr->seq[curr->idx]; 554 do_gettimeofday(&hp_sdc.rtv); 555 curr->idx++; 556 /* Still need to lock here in case of spurious irq. */ 557 write_lock_irq(&hp_sdc.rtq_lock); 558 hp_sdc.rcurr = curridx; 559 write_unlock_irq(&hp_sdc.rtq_lock); 560 hp_sdc_status_out8(postcmd); 561 goto finish; 562 } 563 hp_sdc_status_out8(postcmd); 564 goto actdone; 565 } 566 567 actdone: 568 if (act & HP_SDC_ACT_SEMAPHORE) 569 up(curr->act.semaphore); 570 else if (act & HP_SDC_ACT_CALLBACK) 571 curr->act.irqhook(0,NULL,0,0); 572 573 if (curr->idx >= curr->endidx) { /* This transaction is over. */ 574 if (act & HP_SDC_ACT_DEALLOC) 575 kfree(curr); 576 hp_sdc.tq[curridx] = NULL; 577 } else { 578 curr->actidx = idx + 1; 579 curr->idx = idx + 2; 580 } 581 /* Interleave outbound data between the transactions. */ 582 hp_sdc.wcurr++; 583 if (hp_sdc.wcurr >= HP_SDC_QUEUE_LEN) 584 hp_sdc.wcurr = 0; 585 586 finish: 587 /* If by some quirk IBF has cleared and our ISR has run to 588 see that that has happened, do it all again. */ 589 if (!hp_sdc.ibf && limit++ < 20) 590 goto anew; 591 592 done: 593 if (hp_sdc.wcurr >= 0) 594 tasklet_schedule(&hp_sdc.task); 595 write_unlock(&hp_sdc.lock); 596 597 return 0; 598 } 599 600 /******* Functions called in either user or kernel context ****/ 601 int __hp_sdc_enqueue_transaction(hp_sdc_transaction *this) 602 { 603 int i; 604 605 if (this == NULL) { 606 BUG(); 607 return -EINVAL; 608 } 609 610 /* Can't have same transaction on queue twice */ 611 for (i = 0; i < HP_SDC_QUEUE_LEN; i++) 612 if (hp_sdc.tq[i] == this) 613 goto fail; 614 615 this->actidx = 0; 616 this->idx = 1; 617 618 /* Search for empty slot */ 619 for (i = 0; i < HP_SDC_QUEUE_LEN; i++) 620 if (hp_sdc.tq[i] == NULL) { 621 hp_sdc.tq[i] = this; 622 tasklet_schedule(&hp_sdc.task); 623 return 0; 624 } 625 626 printk(KERN_WARNING PREFIX "No free slot to add transaction.\n"); 627 return -EBUSY; 628 629 fail: 630 printk(KERN_WARNING PREFIX "Transaction add failed: transaction already queued?\n"); 631 return -EINVAL; 632 } 633 634 int hp_sdc_enqueue_transaction(hp_sdc_transaction *this) { 635 unsigned long flags; 636 int ret; 637 638 write_lock_irqsave(&hp_sdc.lock, flags); 639 ret = __hp_sdc_enqueue_transaction(this); 640 write_unlock_irqrestore(&hp_sdc.lock,flags); 641 642 return ret; 643 } 644 645 int hp_sdc_dequeue_transaction(hp_sdc_transaction *this) 646 { 647 unsigned long flags; 648 int i; 649 650 write_lock_irqsave(&hp_sdc.lock, flags); 651 652 /* TODO: don't remove it if it's not done. */ 653 654 for (i = 0; i < HP_SDC_QUEUE_LEN; i++) 655 if (hp_sdc.tq[i] == this) 656 hp_sdc.tq[i] = NULL; 657 658 write_unlock_irqrestore(&hp_sdc.lock, flags); 659 return 0; 660 } 661 662 663 664 /********************** User context functions **************************/ 665 int hp_sdc_request_timer_irq(hp_sdc_irqhook *callback) 666 { 667 if (callback == NULL || hp_sdc.dev == NULL) 668 return -EINVAL; 669 670 write_lock_irq(&hp_sdc.hook_lock); 671 if (hp_sdc.timer != NULL) { 672 write_unlock_irq(&hp_sdc.hook_lock); 673 return -EBUSY; 674 } 675 676 hp_sdc.timer = callback; 677 /* Enable interrupts from the timers */ 678 hp_sdc.im &= ~HP_SDC_IM_FH; 679 hp_sdc.im &= ~HP_SDC_IM_PT; 680 hp_sdc.im &= ~HP_SDC_IM_TIMERS; 681 hp_sdc.set_im = 1; 682 write_unlock_irq(&hp_sdc.hook_lock); 683 684 tasklet_schedule(&hp_sdc.task); 685 686 return 0; 687 } 688 689 int hp_sdc_request_hil_irq(hp_sdc_irqhook *callback) 690 { 691 if (callback == NULL || hp_sdc.dev == NULL) 692 return -EINVAL; 693 694 write_lock_irq(&hp_sdc.hook_lock); 695 if (hp_sdc.hil != NULL) { 696 write_unlock_irq(&hp_sdc.hook_lock); 697 return -EBUSY; 698 } 699 700 hp_sdc.hil = callback; 701 hp_sdc.im &= ~(HP_SDC_IM_HIL | HP_SDC_IM_RESET); 702 hp_sdc.set_im = 1; 703 write_unlock_irq(&hp_sdc.hook_lock); 704 705 tasklet_schedule(&hp_sdc.task); 706 707 return 0; 708 } 709 710 int hp_sdc_request_cooked_irq(hp_sdc_irqhook *callback) 711 { 712 if (callback == NULL || hp_sdc.dev == NULL) 713 return -EINVAL; 714 715 write_lock_irq(&hp_sdc.hook_lock); 716 if (hp_sdc.cooked != NULL) { 717 write_unlock_irq(&hp_sdc.hook_lock); 718 return -EBUSY; 719 } 720 721 /* Enable interrupts from the HIL MLC */ 722 hp_sdc.cooked = callback; 723 hp_sdc.im &= ~(HP_SDC_IM_HIL | HP_SDC_IM_RESET); 724 hp_sdc.set_im = 1; 725 write_unlock_irq(&hp_sdc.hook_lock); 726 727 tasklet_schedule(&hp_sdc.task); 728 729 return 0; 730 } 731 732 int hp_sdc_release_timer_irq(hp_sdc_irqhook *callback) 733 { 734 write_lock_irq(&hp_sdc.hook_lock); 735 if ((callback != hp_sdc.timer) || 736 (hp_sdc.timer == NULL)) { 737 write_unlock_irq(&hp_sdc.hook_lock); 738 return -EINVAL; 739 } 740 741 /* Disable interrupts from the timers */ 742 hp_sdc.timer = NULL; 743 hp_sdc.im |= HP_SDC_IM_TIMERS; 744 hp_sdc.im |= HP_SDC_IM_FH; 745 hp_sdc.im |= HP_SDC_IM_PT; 746 hp_sdc.set_im = 1; 747 write_unlock_irq(&hp_sdc.hook_lock); 748 tasklet_schedule(&hp_sdc.task); 749 750 return 0; 751 } 752 753 int hp_sdc_release_hil_irq(hp_sdc_irqhook *callback) 754 { 755 write_lock_irq(&hp_sdc.hook_lock); 756 if ((callback != hp_sdc.hil) || 757 (hp_sdc.hil == NULL)) { 758 write_unlock_irq(&hp_sdc.hook_lock); 759 return -EINVAL; 760 } 761 762 hp_sdc.hil = NULL; 763 /* Disable interrupts from HIL only if there is no cooked driver. */ 764 if(hp_sdc.cooked == NULL) { 765 hp_sdc.im |= (HP_SDC_IM_HIL | HP_SDC_IM_RESET); 766 hp_sdc.set_im = 1; 767 } 768 write_unlock_irq(&hp_sdc.hook_lock); 769 tasklet_schedule(&hp_sdc.task); 770 771 return 0; 772 } 773 774 int hp_sdc_release_cooked_irq(hp_sdc_irqhook *callback) 775 { 776 write_lock_irq(&hp_sdc.hook_lock); 777 if ((callback != hp_sdc.cooked) || 778 (hp_sdc.cooked == NULL)) { 779 write_unlock_irq(&hp_sdc.hook_lock); 780 return -EINVAL; 781 } 782 783 hp_sdc.cooked = NULL; 784 /* Disable interrupts from HIL only if there is no raw HIL driver. */ 785 if(hp_sdc.hil == NULL) { 786 hp_sdc.im |= (HP_SDC_IM_HIL | HP_SDC_IM_RESET); 787 hp_sdc.set_im = 1; 788 } 789 write_unlock_irq(&hp_sdc.hook_lock); 790 tasklet_schedule(&hp_sdc.task); 791 792 return 0; 793 } 794 795 /************************* Keepalive timer task *********************/ 796 797 static void hp_sdc_kicker(unsigned long data) 798 { 799 tasklet_schedule(&hp_sdc.task); 800 /* Re-insert the periodic task. */ 801 mod_timer(&hp_sdc.kicker, jiffies + HZ); 802 } 803 804 /************************** Module Initialization ***************************/ 805 806 #if defined(__hppa__) 807 808 static const struct parisc_device_id hp_sdc_tbl[] = { 809 { 810 .hw_type = HPHW_FIO, 811 .hversion_rev = HVERSION_REV_ANY_ID, 812 .hversion = HVERSION_ANY_ID, 813 .sversion = 0x73, 814 }, 815 { 0, } 816 }; 817 818 MODULE_DEVICE_TABLE(parisc, hp_sdc_tbl); 819 820 static int __init hp_sdc_init_hppa(struct parisc_device *d); 821 static struct delayed_work moduleloader_work; 822 823 static struct parisc_driver hp_sdc_driver = { 824 .name = "hp_sdc", 825 .id_table = hp_sdc_tbl, 826 .probe = hp_sdc_init_hppa, 827 }; 828 829 #endif /* __hppa__ */ 830 831 static int __init hp_sdc_init(void) 832 { 833 char *errstr; 834 hp_sdc_transaction t_sync; 835 uint8_t ts_sync[6]; 836 struct semaphore s_sync; 837 838 rwlock_init(&hp_sdc.lock); 839 rwlock_init(&hp_sdc.ibf_lock); 840 rwlock_init(&hp_sdc.rtq_lock); 841 rwlock_init(&hp_sdc.hook_lock); 842 843 hp_sdc.timer = NULL; 844 hp_sdc.hil = NULL; 845 hp_sdc.pup = NULL; 846 hp_sdc.cooked = NULL; 847 hp_sdc.im = HP_SDC_IM_MASK; /* Mask maskable irqs */ 848 hp_sdc.set_im = 1; 849 hp_sdc.wi = 0xff; 850 hp_sdc.r7[0] = 0xff; 851 hp_sdc.r7[1] = 0xff; 852 hp_sdc.r7[2] = 0xff; 853 hp_sdc.r7[3] = 0xff; 854 hp_sdc.ibf = 1; 855 856 memset(&hp_sdc.tq, 0, sizeof(hp_sdc.tq)); 857 858 hp_sdc.wcurr = -1; 859 hp_sdc.rcurr = -1; 860 hp_sdc.rqty = 0; 861 862 hp_sdc.dev_err = -ENODEV; 863 864 errstr = "IO not found for"; 865 if (!hp_sdc.base_io) 866 goto err0; 867 868 errstr = "IRQ not found for"; 869 if (!hp_sdc.irq) 870 goto err0; 871 872 hp_sdc.dev_err = -EBUSY; 873 874 #if defined(__hppa__) 875 errstr = "IO not available for"; 876 if (request_region(hp_sdc.data_io, 2, hp_sdc_driver.name)) 877 goto err0; 878 #endif 879 880 errstr = "IRQ not available for"; 881 if (request_irq(hp_sdc.irq, &hp_sdc_isr, IRQF_SHARED, 882 "HP SDC", &hp_sdc)) 883 goto err1; 884 885 errstr = "NMI not available for"; 886 if (request_irq(hp_sdc.nmi, &hp_sdc_nmisr, IRQF_SHARED, 887 "HP SDC NMI", &hp_sdc)) 888 goto err2; 889 890 printk(KERN_INFO PREFIX "HP SDC at 0x%p, IRQ %d (NMI IRQ %d)\n", 891 (void *)hp_sdc.base_io, hp_sdc.irq, hp_sdc.nmi); 892 893 hp_sdc_status_in8(); 894 hp_sdc_data_in8(); 895 896 tasklet_init(&hp_sdc.task, hp_sdc_tasklet, 0); 897 898 /* Sync the output buffer registers, thus scheduling hp_sdc_tasklet. */ 899 t_sync.actidx = 0; 900 t_sync.idx = 1; 901 t_sync.endidx = 6; 902 t_sync.seq = ts_sync; 903 ts_sync[0] = HP_SDC_ACT_DATAREG | HP_SDC_ACT_SEMAPHORE; 904 ts_sync[1] = 0x0f; 905 ts_sync[2] = ts_sync[3] = ts_sync[4] = ts_sync[5] = 0; 906 t_sync.act.semaphore = &s_sync; 907 sema_init(&s_sync, 0); 908 hp_sdc_enqueue_transaction(&t_sync); 909 down(&s_sync); /* Wait for t_sync to complete */ 910 911 /* Create the keepalive task */ 912 init_timer(&hp_sdc.kicker); 913 hp_sdc.kicker.expires = jiffies + HZ; 914 hp_sdc.kicker.function = &hp_sdc_kicker; 915 add_timer(&hp_sdc.kicker); 916 917 hp_sdc.dev_err = 0; 918 return 0; 919 err2: 920 free_irq(hp_sdc.irq, &hp_sdc); 921 err1: 922 release_region(hp_sdc.data_io, 2); 923 err0: 924 printk(KERN_WARNING PREFIX ": %s SDC IO=0x%p IRQ=0x%x NMI=0x%x\n", 925 errstr, (void *)hp_sdc.base_io, hp_sdc.irq, hp_sdc.nmi); 926 hp_sdc.dev = NULL; 927 928 return hp_sdc.dev_err; 929 } 930 931 #if defined(__hppa__) 932 933 static void request_module_delayed(struct work_struct *work) 934 { 935 request_module("hp_sdc_mlc"); 936 } 937 938 static int __init hp_sdc_init_hppa(struct parisc_device *d) 939 { 940 int ret; 941 942 if (!d) 943 return 1; 944 if (hp_sdc.dev != NULL) 945 return 1; /* We only expect one SDC */ 946 947 hp_sdc.dev = d; 948 hp_sdc.irq = d->irq; 949 hp_sdc.nmi = d->aux_irq; 950 hp_sdc.base_io = d->hpa.start; 951 hp_sdc.data_io = d->hpa.start + 0x800; 952 hp_sdc.status_io = d->hpa.start + 0x801; 953 954 INIT_DELAYED_WORK(&moduleloader_work, request_module_delayed); 955 956 ret = hp_sdc_init(); 957 /* after successful initialization give SDC some time to settle 958 * and then load the hp_sdc_mlc upper layer driver */ 959 if (!ret) 960 schedule_delayed_work(&moduleloader_work, 961 msecs_to_jiffies(2000)); 962 963 return ret; 964 } 965 966 #endif /* __hppa__ */ 967 968 static void hp_sdc_exit(void) 969 { 970 /* do nothing if we don't have a SDC */ 971 if (!hp_sdc.dev) 972 return; 973 974 write_lock_irq(&hp_sdc.lock); 975 976 /* Turn off all maskable "sub-function" irq's. */ 977 hp_sdc_spin_ibf(); 978 sdc_writeb(HP_SDC_CMD_SET_IM | HP_SDC_IM_MASK, hp_sdc.status_io); 979 980 /* Wait until we know this has been processed by the i8042 */ 981 hp_sdc_spin_ibf(); 982 983 free_irq(hp_sdc.nmi, &hp_sdc); 984 free_irq(hp_sdc.irq, &hp_sdc); 985 write_unlock_irq(&hp_sdc.lock); 986 987 del_timer_sync(&hp_sdc.kicker); 988 989 tasklet_kill(&hp_sdc.task); 990 991 #if defined(__hppa__) 992 cancel_delayed_work_sync(&moduleloader_work); 993 if (unregister_parisc_driver(&hp_sdc_driver)) 994 printk(KERN_WARNING PREFIX "Error unregistering HP SDC"); 995 #endif 996 } 997 998 static int __init hp_sdc_register(void) 999 { 1000 hp_sdc_transaction tq_init; 1001 uint8_t tq_init_seq[5]; 1002 struct semaphore tq_init_sem; 1003 #if defined(__mc68000__) 1004 mm_segment_t fs; 1005 unsigned char i; 1006 #endif 1007 1008 if (hp_sdc_disabled) { 1009 printk(KERN_WARNING PREFIX "HP SDC driver disabled by no_hpsdc=1.\n"); 1010 return -ENODEV; 1011 } 1012 1013 hp_sdc.dev = NULL; 1014 hp_sdc.dev_err = 0; 1015 #if defined(__hppa__) 1016 if (register_parisc_driver(&hp_sdc_driver)) { 1017 printk(KERN_WARNING PREFIX "Error registering SDC with system bus tree.\n"); 1018 return -ENODEV; 1019 } 1020 #elif defined(__mc68000__) 1021 if (!MACH_IS_HP300) 1022 return -ENODEV; 1023 1024 hp_sdc.irq = 1; 1025 hp_sdc.nmi = 7; 1026 hp_sdc.base_io = (unsigned long) 0xf0428000; 1027 hp_sdc.data_io = (unsigned long) hp_sdc.base_io + 1; 1028 hp_sdc.status_io = (unsigned long) hp_sdc.base_io + 3; 1029 fs = get_fs(); 1030 set_fs(KERNEL_DS); 1031 if (!get_user(i, (unsigned char *)hp_sdc.data_io)) 1032 hp_sdc.dev = (void *)1; 1033 set_fs(fs); 1034 hp_sdc.dev_err = hp_sdc_init(); 1035 #endif 1036 if (hp_sdc.dev == NULL) { 1037 printk(KERN_WARNING PREFIX "No SDC found.\n"); 1038 return hp_sdc.dev_err; 1039 } 1040 1041 sema_init(&tq_init_sem, 0); 1042 1043 tq_init.actidx = 0; 1044 tq_init.idx = 1; 1045 tq_init.endidx = 5; 1046 tq_init.seq = tq_init_seq; 1047 tq_init.act.semaphore = &tq_init_sem; 1048 1049 tq_init_seq[0] = 1050 HP_SDC_ACT_POSTCMD | HP_SDC_ACT_DATAIN | HP_SDC_ACT_SEMAPHORE; 1051 tq_init_seq[1] = HP_SDC_CMD_READ_KCC; 1052 tq_init_seq[2] = 1; 1053 tq_init_seq[3] = 0; 1054 tq_init_seq[4] = 0; 1055 1056 hp_sdc_enqueue_transaction(&tq_init); 1057 1058 down(&tq_init_sem); 1059 up(&tq_init_sem); 1060 1061 if ((tq_init_seq[0] & HP_SDC_ACT_DEAD) == HP_SDC_ACT_DEAD) { 1062 printk(KERN_WARNING PREFIX "Error reading config byte.\n"); 1063 hp_sdc_exit(); 1064 return -ENODEV; 1065 } 1066 hp_sdc.r11 = tq_init_seq[4]; 1067 if (hp_sdc.r11 & HP_SDC_CFG_NEW) { 1068 const char *str; 1069 printk(KERN_INFO PREFIX "New style SDC\n"); 1070 tq_init_seq[1] = HP_SDC_CMD_READ_XTD; 1071 tq_init.actidx = 0; 1072 tq_init.idx = 1; 1073 down(&tq_init_sem); 1074 hp_sdc_enqueue_transaction(&tq_init); 1075 down(&tq_init_sem); 1076 up(&tq_init_sem); 1077 if ((tq_init_seq[0] & HP_SDC_ACT_DEAD) == HP_SDC_ACT_DEAD) { 1078 printk(KERN_WARNING PREFIX "Error reading extended config byte.\n"); 1079 return -ENODEV; 1080 } 1081 hp_sdc.r7e = tq_init_seq[4]; 1082 HP_SDC_XTD_REV_STRINGS(hp_sdc.r7e & HP_SDC_XTD_REV, str) 1083 printk(KERN_INFO PREFIX "Revision: %s\n", str); 1084 if (hp_sdc.r7e & HP_SDC_XTD_BEEPER) 1085 printk(KERN_INFO PREFIX "TI SN76494 beeper present\n"); 1086 if (hp_sdc.r7e & HP_SDC_XTD_BBRTC) 1087 printk(KERN_INFO PREFIX "OKI MSM-58321 BBRTC present\n"); 1088 printk(KERN_INFO PREFIX "Spunking the self test register to force PUP " 1089 "on next firmware reset.\n"); 1090 tq_init_seq[0] = HP_SDC_ACT_PRECMD | 1091 HP_SDC_ACT_DATAOUT | HP_SDC_ACT_SEMAPHORE; 1092 tq_init_seq[1] = HP_SDC_CMD_SET_STR; 1093 tq_init_seq[2] = 1; 1094 tq_init_seq[3] = 0; 1095 tq_init.actidx = 0; 1096 tq_init.idx = 1; 1097 tq_init.endidx = 4; 1098 down(&tq_init_sem); 1099 hp_sdc_enqueue_transaction(&tq_init); 1100 down(&tq_init_sem); 1101 up(&tq_init_sem); 1102 } else 1103 printk(KERN_INFO PREFIX "Old style SDC (1820-%s).\n", 1104 (hp_sdc.r11 & HP_SDC_CFG_REV) ? "3300" : "2564/3087"); 1105 1106 return 0; 1107 } 1108 1109 module_init(hp_sdc_register); 1110 module_exit(hp_sdc_exit); 1111 1112 /* Timing notes: These measurements taken on my 64MHz 7100-LC (715/64) 1113 * cycles cycles-adj time 1114 * between two consecutive mfctl(16)'s: 4 n/a 63ns 1115 * hp_sdc_spin_ibf when idle: 119 115 1.7us 1116 * gsc_writeb status register: 83 79 1.2us 1117 * IBF to clear after sending SET_IM: 6204 6006 93us 1118 * IBF to clear after sending LOAD_RT: 4467 4352 68us 1119 * IBF to clear after sending two LOAD_RTs: 18974 18859 295us 1120 * READ_T1, read status/data, IRQ, call handler: 35564 n/a 556us 1121 * cmd to ~IBF READ_T1 2nd time right after: 5158403 n/a 81ms 1122 * between IRQ received and ~IBF for above: 2578877 n/a 40ms 1123 * 1124 * Performance stats after a run of this module configuring HIL and 1125 * receiving a few mouse events: 1126 * 1127 * status in8 282508 cycles 7128 calls 1128 * status out8 8404 cycles 341 calls 1129 * data out8 1734 cycles 78 calls 1130 * isr 174324 cycles 617 calls (includes take) 1131 * take 1241 cycles 2 calls 1132 * put 1411504 cycles 6937 calls 1133 * task 1655209 cycles 6937 calls (includes put) 1134 * 1135 */ 1136