1 /* 2 * HIL MLC state machine and serio interface driver 3 * 4 * Copyright (c) 2001 Brian S. Julin 5 * All rights reserved. 6 * 7 * Redistribution and use in source and binary forms, with or without 8 * modification, are permitted provided that the following conditions 9 * are met: 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions, and the following disclaimer, 12 * without modification. 13 * 2. The name of the author may not be used to endorse or promote products 14 * derived from this software without specific prior written permission. 15 * 16 * Alternatively, this software may be distributed under the terms of the 17 * GNU General Public License ("GPL"). 18 * 19 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 20 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 21 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 22 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR 23 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 24 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 25 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 26 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 27 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 28 * 29 * References: 30 * HP-HIL Technical Reference Manual. Hewlett Packard Product No. 45918A 31 * 32 * 33 * Driver theory of operation: 34 * 35 * Some access methods and an ISR is defined by the sub-driver 36 * (e.g. hp_sdc_mlc.c). These methods are expected to provide a 37 * few bits of logic in addition to raw access to the HIL MLC, 38 * specifically, the ISR, which is entirely registered by the 39 * sub-driver and invoked directly, must check for record 40 * termination or packet match, at which point a semaphore must 41 * be cleared and then the hil_mlcs_tasklet must be scheduled. 42 * 43 * The hil_mlcs_tasklet processes the state machine for all MLCs 44 * each time it runs, checking each MLC's progress at the current 45 * node in the state machine, and moving the MLC to subsequent nodes 46 * in the state machine when appropriate. It will reschedule 47 * itself if output is pending. (This rescheduling should be replaced 48 * at some point with a sub-driver-specific mechanism.) 49 * 50 * A timer task prods the tasklet once per second to prevent 51 * hangups when attached devices do not return expected data 52 * and to initiate probes of the loop for new devices. 53 */ 54 55 #include <linux/hil_mlc.h> 56 #include <linux/errno.h> 57 #include <linux/kernel.h> 58 #include <linux/module.h> 59 #include <linux/init.h> 60 #include <linux/interrupt.h> 61 #include <linux/slab.h> 62 #include <linux/timer.h> 63 #include <linux/list.h> 64 65 MODULE_AUTHOR("Brian S. Julin <bri@calyx.com>"); 66 MODULE_DESCRIPTION("HIL MLC serio"); 67 MODULE_LICENSE("Dual BSD/GPL"); 68 69 EXPORT_SYMBOL(hil_mlc_register); 70 EXPORT_SYMBOL(hil_mlc_unregister); 71 72 #define PREFIX "HIL MLC: " 73 74 static LIST_HEAD(hil_mlcs); 75 static DEFINE_RWLOCK(hil_mlcs_lock); 76 static struct timer_list hil_mlcs_kicker; 77 static int hil_mlcs_probe; 78 79 static void hil_mlcs_process(unsigned long unused); 80 static DECLARE_TASKLET_DISABLED(hil_mlcs_tasklet, hil_mlcs_process, 0); 81 82 83 /* #define HIL_MLC_DEBUG */ 84 85 /********************** Device info/instance management **********************/ 86 87 static void hil_mlc_clear_di_map(hil_mlc *mlc, int val) 88 { 89 int j; 90 91 for (j = val; j < 7 ; j++) 92 mlc->di_map[j] = -1; 93 } 94 95 static void hil_mlc_clear_di_scratch(hil_mlc *mlc) 96 { 97 memset(&mlc->di_scratch, 0, sizeof(mlc->di_scratch)); 98 } 99 100 static void hil_mlc_copy_di_scratch(hil_mlc *mlc, int idx) 101 { 102 memcpy(&mlc->di[idx], &mlc->di_scratch, sizeof(mlc->di_scratch)); 103 } 104 105 static int hil_mlc_match_di_scratch(hil_mlc *mlc) 106 { 107 int idx; 108 109 for (idx = 0; idx < HIL_MLC_DEVMEM; idx++) { 110 int j, found = 0; 111 112 /* In-use slots are not eligible. */ 113 for (j = 0; j < 7 ; j++) 114 if (mlc->di_map[j] == idx) 115 found++; 116 117 if (found) 118 continue; 119 120 if (!memcmp(mlc->di + idx, &mlc->di_scratch, 121 sizeof(mlc->di_scratch))) 122 break; 123 } 124 return idx >= HIL_MLC_DEVMEM ? -1 : idx; 125 } 126 127 static int hil_mlc_find_free_di(hil_mlc *mlc) 128 { 129 int idx; 130 131 /* TODO: Pick all-zero slots first, failing that, 132 * randomize the slot picked among those eligible. 133 */ 134 for (idx = 0; idx < HIL_MLC_DEVMEM; idx++) { 135 int j, found = 0; 136 137 for (j = 0; j < 7 ; j++) 138 if (mlc->di_map[j] == idx) 139 found++; 140 141 if (!found) 142 break; 143 } 144 145 return idx; /* Note: It is guaranteed at least one above will match */ 146 } 147 148 static inline void hil_mlc_clean_serio_map(hil_mlc *mlc) 149 { 150 int idx; 151 152 for (idx = 0; idx < HIL_MLC_DEVMEM; idx++) { 153 int j, found = 0; 154 155 for (j = 0; j < 7 ; j++) 156 if (mlc->di_map[j] == idx) 157 found++; 158 159 if (!found) 160 mlc->serio_map[idx].di_revmap = -1; 161 } 162 } 163 164 static void hil_mlc_send_polls(hil_mlc *mlc) 165 { 166 int did, i, cnt; 167 struct serio *serio; 168 struct serio_driver *drv; 169 170 i = cnt = 0; 171 did = (mlc->ipacket[0] & HIL_PKT_ADDR_MASK) >> 8; 172 serio = did ? mlc->serio[mlc->di_map[did - 1]] : NULL; 173 drv = (serio != NULL) ? serio->drv : NULL; 174 175 while (mlc->icount < 15 - i) { 176 hil_packet p; 177 178 p = mlc->ipacket[i]; 179 if (did != (p & HIL_PKT_ADDR_MASK) >> 8) { 180 if (drv && drv->interrupt) { 181 drv->interrupt(serio, 0, 0); 182 drv->interrupt(serio, HIL_ERR_INT >> 16, 0); 183 drv->interrupt(serio, HIL_PKT_CMD >> 8, 0); 184 drv->interrupt(serio, HIL_CMD_POL + cnt, 0); 185 } 186 187 did = (p & HIL_PKT_ADDR_MASK) >> 8; 188 serio = did ? mlc->serio[mlc->di_map[did-1]] : NULL; 189 drv = (serio != NULL) ? serio->drv : NULL; 190 cnt = 0; 191 } 192 193 cnt++; 194 i++; 195 196 if (drv && drv->interrupt) { 197 drv->interrupt(serio, (p >> 24), 0); 198 drv->interrupt(serio, (p >> 16) & 0xff, 0); 199 drv->interrupt(serio, (p >> 8) & ~HIL_PKT_ADDR_MASK, 0); 200 drv->interrupt(serio, p & 0xff, 0); 201 } 202 } 203 } 204 205 /*************************** State engine *********************************/ 206 207 #define HILSEN_SCHED 0x000100 /* Schedule the tasklet */ 208 #define HILSEN_BREAK 0x000200 /* Wait until next pass */ 209 #define HILSEN_UP 0x000400 /* relative node#, decrement */ 210 #define HILSEN_DOWN 0x000800 /* relative node#, increment */ 211 #define HILSEN_FOLLOW 0x001000 /* use retval as next node# */ 212 213 #define HILSEN_MASK 0x0000ff 214 #define HILSEN_START 0 215 #define HILSEN_RESTART 1 216 #define HILSEN_DHR 9 217 #define HILSEN_DHR2 10 218 #define HILSEN_IFC 14 219 #define HILSEN_HEAL0 16 220 #define HILSEN_HEAL 18 221 #define HILSEN_ACF 21 222 #define HILSEN_ACF2 22 223 #define HILSEN_DISC0 25 224 #define HILSEN_DISC 27 225 #define HILSEN_MATCH 40 226 #define HILSEN_OPERATE 41 227 #define HILSEN_PROBE 44 228 #define HILSEN_DSR 52 229 #define HILSEN_REPOLL 55 230 #define HILSEN_IFCACF 58 231 #define HILSEN_END 60 232 233 #define HILSEN_NEXT (HILSEN_DOWN | 1) 234 #define HILSEN_SAME (HILSEN_DOWN | 0) 235 #define HILSEN_LAST (HILSEN_UP | 1) 236 237 #define HILSEN_DOZE (HILSEN_SAME | HILSEN_SCHED | HILSEN_BREAK) 238 #define HILSEN_SLEEP (HILSEN_SAME | HILSEN_BREAK) 239 240 static int hilse_match(hil_mlc *mlc, int unused) 241 { 242 int rc; 243 244 rc = hil_mlc_match_di_scratch(mlc); 245 if (rc == -1) { 246 rc = hil_mlc_find_free_di(mlc); 247 if (rc == -1) 248 goto err; 249 250 #ifdef HIL_MLC_DEBUG 251 printk(KERN_DEBUG PREFIX "new in slot %i\n", rc); 252 #endif 253 hil_mlc_copy_di_scratch(mlc, rc); 254 mlc->di_map[mlc->ddi] = rc; 255 mlc->serio_map[rc].di_revmap = mlc->ddi; 256 hil_mlc_clean_serio_map(mlc); 257 serio_rescan(mlc->serio[rc]); 258 return -1; 259 } 260 261 mlc->di_map[mlc->ddi] = rc; 262 #ifdef HIL_MLC_DEBUG 263 printk(KERN_DEBUG PREFIX "same in slot %i\n", rc); 264 #endif 265 mlc->serio_map[rc].di_revmap = mlc->ddi; 266 hil_mlc_clean_serio_map(mlc); 267 return 0; 268 269 err: 270 printk(KERN_ERR PREFIX "Residual device slots exhausted, close some serios!\n"); 271 return 1; 272 } 273 274 /* An LCV used to prevent runaway loops, forces 5 second sleep when reset. */ 275 static int hilse_init_lcv(hil_mlc *mlc, int unused) 276 { 277 struct timeval tv; 278 279 do_gettimeofday(&tv); 280 281 if (mlc->lcv && (tv.tv_sec - mlc->lcv_tv.tv_sec) < 5) 282 return -1; 283 284 mlc->lcv_tv = tv; 285 mlc->lcv = 0; 286 287 return 0; 288 } 289 290 static int hilse_inc_lcv(hil_mlc *mlc, int lim) 291 { 292 return mlc->lcv++ >= lim ? -1 : 0; 293 } 294 295 #if 0 296 static int hilse_set_lcv(hil_mlc *mlc, int val) 297 { 298 mlc->lcv = val; 299 300 return 0; 301 } 302 #endif 303 304 /* Management of the discovered device index (zero based, -1 means no devs) */ 305 static int hilse_set_ddi(hil_mlc *mlc, int val) 306 { 307 mlc->ddi = val; 308 hil_mlc_clear_di_map(mlc, val + 1); 309 310 return 0; 311 } 312 313 static int hilse_dec_ddi(hil_mlc *mlc, int unused) 314 { 315 mlc->ddi--; 316 if (mlc->ddi <= -1) { 317 mlc->ddi = -1; 318 hil_mlc_clear_di_map(mlc, 0); 319 return -1; 320 } 321 hil_mlc_clear_di_map(mlc, mlc->ddi + 1); 322 323 return 0; 324 } 325 326 static int hilse_inc_ddi(hil_mlc *mlc, int unused) 327 { 328 BUG_ON(mlc->ddi >= 6); 329 mlc->ddi++; 330 331 return 0; 332 } 333 334 static int hilse_take_idd(hil_mlc *mlc, int unused) 335 { 336 int i; 337 338 /* Help the state engine: 339 * Is this a real IDD response or just an echo? 340 * 341 * Real IDD response does not start with a command. 342 */ 343 if (mlc->ipacket[0] & HIL_PKT_CMD) 344 goto bail; 345 346 /* Should have the command echoed further down. */ 347 for (i = 1; i < 16; i++) { 348 if (((mlc->ipacket[i] & HIL_PKT_ADDR_MASK) == 349 (mlc->ipacket[0] & HIL_PKT_ADDR_MASK)) && 350 (mlc->ipacket[i] & HIL_PKT_CMD) && 351 ((mlc->ipacket[i] & HIL_PKT_DATA_MASK) == HIL_CMD_IDD)) 352 break; 353 } 354 if (i > 15) 355 goto bail; 356 357 /* And the rest of the packets should still be clear. */ 358 while (++i < 16) 359 if (mlc->ipacket[i]) 360 break; 361 362 if (i < 16) 363 goto bail; 364 365 for (i = 0; i < 16; i++) 366 mlc->di_scratch.idd[i] = 367 mlc->ipacket[i] & HIL_PKT_DATA_MASK; 368 369 /* Next step is to see if RSC supported */ 370 if (mlc->di_scratch.idd[1] & HIL_IDD_HEADER_RSC) 371 return HILSEN_NEXT; 372 373 if (mlc->di_scratch.idd[1] & HIL_IDD_HEADER_EXD) 374 return HILSEN_DOWN | 4; 375 376 return 0; 377 378 bail: 379 mlc->ddi--; 380 381 return -1; /* This should send us off to ACF */ 382 } 383 384 static int hilse_take_rsc(hil_mlc *mlc, int unused) 385 { 386 int i; 387 388 for (i = 0; i < 16; i++) 389 mlc->di_scratch.rsc[i] = 390 mlc->ipacket[i] & HIL_PKT_DATA_MASK; 391 392 /* Next step is to see if EXD supported (IDD has already been read) */ 393 if (mlc->di_scratch.idd[1] & HIL_IDD_HEADER_EXD) 394 return HILSEN_NEXT; 395 396 return 0; 397 } 398 399 static int hilse_take_exd(hil_mlc *mlc, int unused) 400 { 401 int i; 402 403 for (i = 0; i < 16; i++) 404 mlc->di_scratch.exd[i] = 405 mlc->ipacket[i] & HIL_PKT_DATA_MASK; 406 407 /* Next step is to see if RNM supported. */ 408 if (mlc->di_scratch.exd[0] & HIL_EXD_HEADER_RNM) 409 return HILSEN_NEXT; 410 411 return 0; 412 } 413 414 static int hilse_take_rnm(hil_mlc *mlc, int unused) 415 { 416 int i; 417 418 for (i = 0; i < 16; i++) 419 mlc->di_scratch.rnm[i] = 420 mlc->ipacket[i] & HIL_PKT_DATA_MASK; 421 422 printk(KERN_INFO PREFIX "Device name gotten: %16s\n", 423 mlc->di_scratch.rnm); 424 425 return 0; 426 } 427 428 static int hilse_operate(hil_mlc *mlc, int repoll) 429 { 430 431 if (mlc->opercnt == 0) 432 hil_mlcs_probe = 0; 433 mlc->opercnt = 1; 434 435 hil_mlc_send_polls(mlc); 436 437 if (!hil_mlcs_probe) 438 return 0; 439 hil_mlcs_probe = 0; 440 mlc->opercnt = 0; 441 return 1; 442 } 443 444 #define FUNC(funct, funct_arg, zero_rc, neg_rc, pos_rc) \ 445 { HILSE_FUNC, { .func = funct }, funct_arg, zero_rc, neg_rc, pos_rc }, 446 #define OUT(pack) \ 447 { HILSE_OUT, { .packet = pack }, 0, HILSEN_NEXT, HILSEN_DOZE, 0 }, 448 #define CTS \ 449 { HILSE_CTS, { .packet = 0 }, 0, HILSEN_NEXT | HILSEN_SCHED | HILSEN_BREAK, HILSEN_DOZE, 0 }, 450 #define EXPECT(comp, to, got, got_wrong, timed_out) \ 451 { HILSE_EXPECT, { .packet = comp }, to, got, got_wrong, timed_out }, 452 #define EXPECT_LAST(comp, to, got, got_wrong, timed_out) \ 453 { HILSE_EXPECT_LAST, { .packet = comp }, to, got, got_wrong, timed_out }, 454 #define EXPECT_DISC(comp, to, got, got_wrong, timed_out) \ 455 { HILSE_EXPECT_DISC, { .packet = comp }, to, got, got_wrong, timed_out }, 456 #define IN(to, got, got_error, timed_out) \ 457 { HILSE_IN, { .packet = 0 }, to, got, got_error, timed_out }, 458 #define OUT_DISC(pack) \ 459 { HILSE_OUT_DISC, { .packet = pack }, 0, 0, 0, 0 }, 460 #define OUT_LAST(pack) \ 461 { HILSE_OUT_LAST, { .packet = pack }, 0, 0, 0, 0 }, 462 463 static const struct hilse_node hil_mlc_se[HILSEN_END] = { 464 465 /* 0 HILSEN_START */ 466 FUNC(hilse_init_lcv, 0, HILSEN_NEXT, HILSEN_SLEEP, 0) 467 468 /* 1 HILSEN_RESTART */ 469 FUNC(hilse_inc_lcv, 10, HILSEN_NEXT, HILSEN_START, 0) 470 OUT(HIL_CTRL_ONLY) /* Disable APE */ 471 CTS 472 473 #define TEST_PACKET(x) \ 474 (HIL_PKT_CMD | (x << HIL_PKT_ADDR_SHIFT) | x << 4 | x) 475 476 OUT(HIL_DO_ALTER_CTRL | HIL_CTRL_TEST | TEST_PACKET(0x5)) 477 EXPECT(HIL_ERR_INT | TEST_PACKET(0x5), 478 2000, HILSEN_NEXT, HILSEN_RESTART, HILSEN_RESTART) 479 OUT(HIL_DO_ALTER_CTRL | HIL_CTRL_TEST | TEST_PACKET(0xa)) 480 EXPECT(HIL_ERR_INT | TEST_PACKET(0xa), 481 2000, HILSEN_NEXT, HILSEN_RESTART, HILSEN_RESTART) 482 OUT(HIL_CTRL_ONLY | 0) /* Disable test mode */ 483 484 /* 9 HILSEN_DHR */ 485 FUNC(hilse_init_lcv, 0, HILSEN_NEXT, HILSEN_SLEEP, 0) 486 487 /* 10 HILSEN_DHR2 */ 488 FUNC(hilse_inc_lcv, 10, HILSEN_NEXT, HILSEN_START, 0) 489 FUNC(hilse_set_ddi, -1, HILSEN_NEXT, 0, 0) 490 OUT(HIL_PKT_CMD | HIL_CMD_DHR) 491 IN(300000, HILSEN_DHR2, HILSEN_DHR2, HILSEN_NEXT) 492 493 /* 14 HILSEN_IFC */ 494 OUT(HIL_PKT_CMD | HIL_CMD_IFC) 495 EXPECT(HIL_PKT_CMD | HIL_CMD_IFC | HIL_ERR_INT, 496 20000, HILSEN_DISC, HILSEN_DHR2, HILSEN_NEXT ) 497 498 /* If devices are there, they weren't in PUP or other loopback mode. 499 * We're more concerned at this point with restoring operation 500 * to devices than discovering new ones, so we try to salvage 501 * the loop configuration by closing off the loop. 502 */ 503 504 /* 16 HILSEN_HEAL0 */ 505 FUNC(hilse_dec_ddi, 0, HILSEN_NEXT, HILSEN_ACF, 0) 506 FUNC(hilse_inc_ddi, 0, HILSEN_NEXT, 0, 0) 507 508 /* 18 HILSEN_HEAL */ 509 OUT_LAST(HIL_CMD_ELB) 510 EXPECT_LAST(HIL_CMD_ELB | HIL_ERR_INT, 511 20000, HILSEN_REPOLL, HILSEN_DSR, HILSEN_NEXT) 512 FUNC(hilse_dec_ddi, 0, HILSEN_HEAL, HILSEN_NEXT, 0) 513 514 /* 21 HILSEN_ACF */ 515 FUNC(hilse_init_lcv, 0, HILSEN_NEXT, HILSEN_DOZE, 0) 516 517 /* 22 HILSEN_ACF2 */ 518 FUNC(hilse_inc_lcv, 10, HILSEN_NEXT, HILSEN_START, 0) 519 OUT(HIL_PKT_CMD | HIL_CMD_ACF | 1) 520 IN(20000, HILSEN_NEXT, HILSEN_DSR, HILSEN_NEXT) 521 522 /* 25 HILSEN_DISC0 */ 523 OUT_DISC(HIL_PKT_CMD | HIL_CMD_ELB) 524 EXPECT_DISC(HIL_PKT_CMD | HIL_CMD_ELB | HIL_ERR_INT, 525 20000, HILSEN_NEXT, HILSEN_DSR, HILSEN_DSR) 526 527 /* Only enter here if response just received */ 528 /* 27 HILSEN_DISC */ 529 OUT_DISC(HIL_PKT_CMD | HIL_CMD_IDD) 530 EXPECT_DISC(HIL_PKT_CMD | HIL_CMD_IDD | HIL_ERR_INT, 531 20000, HILSEN_NEXT, HILSEN_DSR, HILSEN_START) 532 FUNC(hilse_inc_ddi, 0, HILSEN_NEXT, HILSEN_START, 0) 533 FUNC(hilse_take_idd, 0, HILSEN_MATCH, HILSEN_IFCACF, HILSEN_FOLLOW) 534 OUT_LAST(HIL_PKT_CMD | HIL_CMD_RSC) 535 EXPECT_LAST(HIL_PKT_CMD | HIL_CMD_RSC | HIL_ERR_INT, 536 30000, HILSEN_NEXT, HILSEN_DSR, HILSEN_DSR) 537 FUNC(hilse_take_rsc, 0, HILSEN_MATCH, 0, HILSEN_FOLLOW) 538 OUT_LAST(HIL_PKT_CMD | HIL_CMD_EXD) 539 EXPECT_LAST(HIL_PKT_CMD | HIL_CMD_EXD | HIL_ERR_INT, 540 30000, HILSEN_NEXT, HILSEN_DSR, HILSEN_DSR) 541 FUNC(hilse_take_exd, 0, HILSEN_MATCH, 0, HILSEN_FOLLOW) 542 OUT_LAST(HIL_PKT_CMD | HIL_CMD_RNM) 543 EXPECT_LAST(HIL_PKT_CMD | HIL_CMD_RNM | HIL_ERR_INT, 544 30000, HILSEN_NEXT, HILSEN_DSR, HILSEN_DSR) 545 FUNC(hilse_take_rnm, 0, HILSEN_MATCH, 0, 0) 546 547 /* 40 HILSEN_MATCH */ 548 FUNC(hilse_match, 0, HILSEN_NEXT, HILSEN_NEXT, /* TODO */ 0) 549 550 /* 41 HILSEN_OPERATE */ 551 OUT(HIL_PKT_CMD | HIL_CMD_POL) 552 EXPECT(HIL_PKT_CMD | HIL_CMD_POL | HIL_ERR_INT, 553 20000, HILSEN_NEXT, HILSEN_DSR, HILSEN_NEXT) 554 FUNC(hilse_operate, 0, HILSEN_OPERATE, HILSEN_IFC, HILSEN_NEXT) 555 556 /* 44 HILSEN_PROBE */ 557 OUT_LAST(HIL_PKT_CMD | HIL_CMD_EPT) 558 IN(10000, HILSEN_DISC, HILSEN_DSR, HILSEN_NEXT) 559 OUT_DISC(HIL_PKT_CMD | HIL_CMD_ELB) 560 IN(10000, HILSEN_DISC, HILSEN_DSR, HILSEN_NEXT) 561 OUT(HIL_PKT_CMD | HIL_CMD_ACF | 1) 562 IN(10000, HILSEN_DISC0, HILSEN_DSR, HILSEN_NEXT) 563 OUT_LAST(HIL_PKT_CMD | HIL_CMD_ELB) 564 IN(10000, HILSEN_OPERATE, HILSEN_DSR, HILSEN_DSR) 565 566 /* 52 HILSEN_DSR */ 567 FUNC(hilse_set_ddi, -1, HILSEN_NEXT, 0, 0) 568 OUT(HIL_PKT_CMD | HIL_CMD_DSR) 569 IN(20000, HILSEN_DHR, HILSEN_DHR, HILSEN_IFC) 570 571 /* 55 HILSEN_REPOLL */ 572 OUT(HIL_PKT_CMD | HIL_CMD_RPL) 573 EXPECT(HIL_PKT_CMD | HIL_CMD_RPL | HIL_ERR_INT, 574 20000, HILSEN_NEXT, HILSEN_DSR, HILSEN_NEXT) 575 FUNC(hilse_operate, 1, HILSEN_OPERATE, HILSEN_IFC, HILSEN_PROBE) 576 577 /* 58 HILSEN_IFCACF */ 578 OUT(HIL_PKT_CMD | HIL_CMD_IFC) 579 EXPECT(HIL_PKT_CMD | HIL_CMD_IFC | HIL_ERR_INT, 580 20000, HILSEN_ACF2, HILSEN_DHR2, HILSEN_HEAL) 581 582 /* 60 HILSEN_END */ 583 }; 584 585 static inline void hilse_setup_input(hil_mlc *mlc, const struct hilse_node *node) 586 { 587 588 switch (node->act) { 589 case HILSE_EXPECT_DISC: 590 mlc->imatch = node->object.packet; 591 mlc->imatch |= ((mlc->ddi + 2) << HIL_PKT_ADDR_SHIFT); 592 break; 593 case HILSE_EXPECT_LAST: 594 mlc->imatch = node->object.packet; 595 mlc->imatch |= ((mlc->ddi + 1) << HIL_PKT_ADDR_SHIFT); 596 break; 597 case HILSE_EXPECT: 598 mlc->imatch = node->object.packet; 599 break; 600 case HILSE_IN: 601 mlc->imatch = 0; 602 break; 603 default: 604 BUG(); 605 } 606 mlc->istarted = 1; 607 mlc->intimeout = node->arg; 608 do_gettimeofday(&(mlc->instart)); 609 mlc->icount = 15; 610 memset(mlc->ipacket, 0, 16 * sizeof(hil_packet)); 611 BUG_ON(down_trylock(&mlc->isem)); 612 } 613 614 #ifdef HIL_MLC_DEBUG 615 static int doze; 616 static int seidx; /* For debug */ 617 #endif 618 619 static int hilse_donode(hil_mlc *mlc) 620 { 621 const struct hilse_node *node; 622 int nextidx = 0; 623 int sched_long = 0; 624 unsigned long flags; 625 626 #ifdef HIL_MLC_DEBUG 627 if (mlc->seidx && mlc->seidx != seidx && 628 mlc->seidx != 41 && mlc->seidx != 42 && mlc->seidx != 43) { 629 printk(KERN_DEBUG PREFIX "z%i \n {%i}", doze, mlc->seidx); 630 doze = 0; 631 } 632 633 seidx = mlc->seidx; 634 #endif 635 node = hil_mlc_se + mlc->seidx; 636 637 switch (node->act) { 638 int rc; 639 hil_packet pack; 640 641 case HILSE_FUNC: 642 BUG_ON(node->object.func == NULL); 643 rc = node->object.func(mlc, node->arg); 644 nextidx = (rc > 0) ? node->ugly : 645 ((rc < 0) ? node->bad : node->good); 646 if (nextidx == HILSEN_FOLLOW) 647 nextidx = rc; 648 break; 649 650 case HILSE_EXPECT_LAST: 651 case HILSE_EXPECT_DISC: 652 case HILSE_EXPECT: 653 case HILSE_IN: 654 /* Already set up from previous HILSE_OUT_* */ 655 write_lock_irqsave(&mlc->lock, flags); 656 rc = mlc->in(mlc, node->arg); 657 if (rc == 2) { 658 nextidx = HILSEN_DOZE; 659 sched_long = 1; 660 write_unlock_irqrestore(&mlc->lock, flags); 661 break; 662 } 663 if (rc == 1) 664 nextidx = node->ugly; 665 else if (rc == 0) 666 nextidx = node->good; 667 else 668 nextidx = node->bad; 669 mlc->istarted = 0; 670 write_unlock_irqrestore(&mlc->lock, flags); 671 break; 672 673 case HILSE_OUT_LAST: 674 write_lock_irqsave(&mlc->lock, flags); 675 pack = node->object.packet; 676 pack |= ((mlc->ddi + 1) << HIL_PKT_ADDR_SHIFT); 677 goto out; 678 679 case HILSE_OUT_DISC: 680 write_lock_irqsave(&mlc->lock, flags); 681 pack = node->object.packet; 682 pack |= ((mlc->ddi + 2) << HIL_PKT_ADDR_SHIFT); 683 goto out; 684 685 case HILSE_OUT: 686 write_lock_irqsave(&mlc->lock, flags); 687 pack = node->object.packet; 688 out: 689 if (!mlc->istarted) { 690 /* Prepare to receive input */ 691 if ((node + 1)->act & HILSE_IN) 692 hilse_setup_input(mlc, node + 1); 693 } 694 695 write_unlock_irqrestore(&mlc->lock, flags); 696 697 if (down_trylock(&mlc->osem)) { 698 nextidx = HILSEN_DOZE; 699 break; 700 } 701 up(&mlc->osem); 702 703 write_lock_irqsave(&mlc->lock, flags); 704 if (!mlc->ostarted) { 705 mlc->ostarted = 1; 706 mlc->opacket = pack; 707 mlc->out(mlc); 708 nextidx = HILSEN_DOZE; 709 write_unlock_irqrestore(&mlc->lock, flags); 710 break; 711 } 712 mlc->ostarted = 0; 713 do_gettimeofday(&(mlc->instart)); 714 write_unlock_irqrestore(&mlc->lock, flags); 715 nextidx = HILSEN_NEXT; 716 break; 717 718 case HILSE_CTS: 719 write_lock_irqsave(&mlc->lock, flags); 720 nextidx = mlc->cts(mlc) ? node->bad : node->good; 721 write_unlock_irqrestore(&mlc->lock, flags); 722 break; 723 724 default: 725 BUG(); 726 } 727 728 #ifdef HIL_MLC_DEBUG 729 if (nextidx == HILSEN_DOZE) 730 doze++; 731 #endif 732 733 while (nextidx & HILSEN_SCHED) { 734 struct timeval tv; 735 736 if (!sched_long) 737 goto sched; 738 739 do_gettimeofday(&tv); 740 tv.tv_usec += USEC_PER_SEC * (tv.tv_sec - mlc->instart.tv_sec); 741 tv.tv_usec -= mlc->instart.tv_usec; 742 if (tv.tv_usec >= mlc->intimeout) goto sched; 743 tv.tv_usec = (mlc->intimeout - tv.tv_usec) * HZ / USEC_PER_SEC; 744 if (!tv.tv_usec) goto sched; 745 mod_timer(&hil_mlcs_kicker, jiffies + tv.tv_usec); 746 break; 747 sched: 748 tasklet_schedule(&hil_mlcs_tasklet); 749 break; 750 } 751 752 if (nextidx & HILSEN_DOWN) 753 mlc->seidx += nextidx & HILSEN_MASK; 754 else if (nextidx & HILSEN_UP) 755 mlc->seidx -= nextidx & HILSEN_MASK; 756 else 757 mlc->seidx = nextidx & HILSEN_MASK; 758 759 if (nextidx & HILSEN_BREAK) 760 return 1; 761 762 return 0; 763 } 764 765 /******************** tasklet context functions **************************/ 766 static void hil_mlcs_process(unsigned long unused) 767 { 768 struct list_head *tmp; 769 770 read_lock(&hil_mlcs_lock); 771 list_for_each(tmp, &hil_mlcs) { 772 struct hil_mlc *mlc = list_entry(tmp, hil_mlc, list); 773 while (hilse_donode(mlc) == 0) { 774 #ifdef HIL_MLC_DEBUG 775 if (mlc->seidx != 41 && 776 mlc->seidx != 42 && 777 mlc->seidx != 43) 778 printk(KERN_DEBUG PREFIX " + "); 779 #endif 780 } 781 } 782 read_unlock(&hil_mlcs_lock); 783 } 784 785 /************************* Keepalive timer task *********************/ 786 787 static void hil_mlcs_timer(unsigned long data) 788 { 789 hil_mlcs_probe = 1; 790 tasklet_schedule(&hil_mlcs_tasklet); 791 /* Re-insert the periodic task. */ 792 if (!timer_pending(&hil_mlcs_kicker)) 793 mod_timer(&hil_mlcs_kicker, jiffies + HZ); 794 } 795 796 /******************** user/kernel context functions **********************/ 797 798 static int hil_mlc_serio_write(struct serio *serio, unsigned char c) 799 { 800 struct hil_mlc_serio_map *map; 801 struct hil_mlc *mlc; 802 struct serio_driver *drv; 803 uint8_t *idx, *last; 804 805 map = serio->port_data; 806 BUG_ON(map == NULL); 807 808 mlc = map->mlc; 809 BUG_ON(mlc == NULL); 810 811 mlc->serio_opacket[map->didx] |= 812 ((hil_packet)c) << (8 * (3 - mlc->serio_oidx[map->didx])); 813 814 if (mlc->serio_oidx[map->didx] >= 3) { 815 /* for now only commands */ 816 if (!(mlc->serio_opacket[map->didx] & HIL_PKT_CMD)) 817 return -EIO; 818 switch (mlc->serio_opacket[map->didx] & HIL_PKT_DATA_MASK) { 819 case HIL_CMD_IDD: 820 idx = mlc->di[map->didx].idd; 821 goto emu; 822 case HIL_CMD_RSC: 823 idx = mlc->di[map->didx].rsc; 824 goto emu; 825 case HIL_CMD_EXD: 826 idx = mlc->di[map->didx].exd; 827 goto emu; 828 case HIL_CMD_RNM: 829 idx = mlc->di[map->didx].rnm; 830 goto emu; 831 default: 832 break; 833 } 834 mlc->serio_oidx[map->didx] = 0; 835 mlc->serio_opacket[map->didx] = 0; 836 } 837 838 mlc->serio_oidx[map->didx]++; 839 return -EIO; 840 emu: 841 drv = serio->drv; 842 BUG_ON(drv == NULL); 843 844 last = idx + 15; 845 while ((last != idx) && (*last == 0)) 846 last--; 847 848 while (idx != last) { 849 drv->interrupt(serio, 0, 0); 850 drv->interrupt(serio, HIL_ERR_INT >> 16, 0); 851 drv->interrupt(serio, 0, 0); 852 drv->interrupt(serio, *idx, 0); 853 idx++; 854 } 855 drv->interrupt(serio, 0, 0); 856 drv->interrupt(serio, HIL_ERR_INT >> 16, 0); 857 drv->interrupt(serio, HIL_PKT_CMD >> 8, 0); 858 drv->interrupt(serio, *idx, 0); 859 860 mlc->serio_oidx[map->didx] = 0; 861 mlc->serio_opacket[map->didx] = 0; 862 863 return 0; 864 } 865 866 static int hil_mlc_serio_open(struct serio *serio) 867 { 868 struct hil_mlc_serio_map *map; 869 struct hil_mlc *mlc; 870 871 if (serio_get_drvdata(serio) != NULL) 872 return -EBUSY; 873 874 map = serio->port_data; 875 BUG_ON(map == NULL); 876 877 mlc = map->mlc; 878 BUG_ON(mlc == NULL); 879 880 return 0; 881 } 882 883 static void hil_mlc_serio_close(struct serio *serio) 884 { 885 struct hil_mlc_serio_map *map; 886 struct hil_mlc *mlc; 887 888 map = serio->port_data; 889 BUG_ON(map == NULL); 890 891 mlc = map->mlc; 892 BUG_ON(mlc == NULL); 893 894 serio_set_drvdata(serio, NULL); 895 serio->drv = NULL; 896 /* TODO wake up interruptable */ 897 } 898 899 static const struct serio_device_id hil_mlc_serio_id = { 900 .type = SERIO_HIL_MLC, 901 .proto = SERIO_HIL, 902 .extra = SERIO_ANY, 903 .id = SERIO_ANY, 904 }; 905 906 int hil_mlc_register(hil_mlc *mlc) 907 { 908 int i; 909 unsigned long flags; 910 911 BUG_ON(mlc == NULL); 912 913 mlc->istarted = 0; 914 mlc->ostarted = 0; 915 916 rwlock_init(&mlc->lock); 917 sema_init(&mlc->osem, 1); 918 919 sema_init(&mlc->isem, 1); 920 mlc->icount = -1; 921 mlc->imatch = 0; 922 923 mlc->opercnt = 0; 924 925 sema_init(&(mlc->csem), 0); 926 927 hil_mlc_clear_di_scratch(mlc); 928 hil_mlc_clear_di_map(mlc, 0); 929 for (i = 0; i < HIL_MLC_DEVMEM; i++) { 930 struct serio *mlc_serio; 931 hil_mlc_copy_di_scratch(mlc, i); 932 mlc_serio = kzalloc(sizeof(*mlc_serio), GFP_KERNEL); 933 mlc->serio[i] = mlc_serio; 934 if (!mlc->serio[i]) { 935 for (; i >= 0; i--) 936 kfree(mlc->serio[i]); 937 return -ENOMEM; 938 } 939 snprintf(mlc_serio->name, sizeof(mlc_serio->name)-1, "HIL_SERIO%d", i); 940 snprintf(mlc_serio->phys, sizeof(mlc_serio->phys)-1, "HIL%d", i); 941 mlc_serio->id = hil_mlc_serio_id; 942 mlc_serio->id.id = i; /* HIL port no. */ 943 mlc_serio->write = hil_mlc_serio_write; 944 mlc_serio->open = hil_mlc_serio_open; 945 mlc_serio->close = hil_mlc_serio_close; 946 mlc_serio->port_data = &(mlc->serio_map[i]); 947 mlc->serio_map[i].mlc = mlc; 948 mlc->serio_map[i].didx = i; 949 mlc->serio_map[i].di_revmap = -1; 950 mlc->serio_opacket[i] = 0; 951 mlc->serio_oidx[i] = 0; 952 serio_register_port(mlc_serio); 953 } 954 955 mlc->tasklet = &hil_mlcs_tasklet; 956 957 write_lock_irqsave(&hil_mlcs_lock, flags); 958 list_add_tail(&mlc->list, &hil_mlcs); 959 mlc->seidx = HILSEN_START; 960 write_unlock_irqrestore(&hil_mlcs_lock, flags); 961 962 tasklet_schedule(&hil_mlcs_tasklet); 963 return 0; 964 } 965 966 int hil_mlc_unregister(hil_mlc *mlc) 967 { 968 struct list_head *tmp; 969 unsigned long flags; 970 int i; 971 972 BUG_ON(mlc == NULL); 973 974 write_lock_irqsave(&hil_mlcs_lock, flags); 975 list_for_each(tmp, &hil_mlcs) 976 if (list_entry(tmp, hil_mlc, list) == mlc) 977 goto found; 978 979 /* not found in list */ 980 write_unlock_irqrestore(&hil_mlcs_lock, flags); 981 tasklet_schedule(&hil_mlcs_tasklet); 982 return -ENODEV; 983 984 found: 985 list_del(tmp); 986 write_unlock_irqrestore(&hil_mlcs_lock, flags); 987 988 for (i = 0; i < HIL_MLC_DEVMEM; i++) { 989 serio_unregister_port(mlc->serio[i]); 990 mlc->serio[i] = NULL; 991 } 992 993 tasklet_schedule(&hil_mlcs_tasklet); 994 return 0; 995 } 996 997 /**************************** Module interface *************************/ 998 999 static int __init hil_mlc_init(void) 1000 { 1001 setup_timer(&hil_mlcs_kicker, &hil_mlcs_timer, 0); 1002 mod_timer(&hil_mlcs_kicker, jiffies + HZ); 1003 1004 tasklet_enable(&hil_mlcs_tasklet); 1005 1006 return 0; 1007 } 1008 1009 static void __exit hil_mlc_exit(void) 1010 { 1011 del_timer_sync(&hil_mlcs_kicker); 1012 tasklet_kill(&hil_mlcs_tasklet); 1013 } 1014 1015 module_init(hil_mlc_init); 1016 module_exit(hil_mlc_exit); 1017