1 // SPDX-License-Identifier: GPL-2.0 or BSD-3-Clause 2 /* 3 * Copyright(c) 2015, 2016 Intel Corporation. 4 */ 5 6 #include <linux/delay.h> 7 #include <linux/pci.h> 8 #include <linux/vmalloc.h> 9 10 #include "hfi.h" 11 12 /* for the given bus number, return the CSR for reading an i2c line */ 13 static inline u32 i2c_in_csr(u32 bus_num) 14 { 15 return bus_num ? ASIC_QSFP2_IN : ASIC_QSFP1_IN; 16 } 17 18 /* for the given bus number, return the CSR for writing an i2c line */ 19 static inline u32 i2c_oe_csr(u32 bus_num) 20 { 21 return bus_num ? ASIC_QSFP2_OE : ASIC_QSFP1_OE; 22 } 23 24 static void hfi1_setsda(void *data, int state) 25 { 26 struct hfi1_i2c_bus *bus = (struct hfi1_i2c_bus *)data; 27 struct hfi1_devdata *dd = bus->controlling_dd; 28 u64 reg; 29 u32 target_oe; 30 31 target_oe = i2c_oe_csr(bus->num); 32 reg = read_csr(dd, target_oe); 33 /* 34 * The OE bit value is inverted and connected to the pin. When 35 * OE is 0 the pin is left to be pulled up, when the OE is 1 36 * the pin is driven low. This matches the "open drain" or "open 37 * collector" convention. 38 */ 39 if (state) 40 reg &= ~QSFP_HFI0_I2CDAT; 41 else 42 reg |= QSFP_HFI0_I2CDAT; 43 write_csr(dd, target_oe, reg); 44 /* do a read to force the write into the chip */ 45 (void)read_csr(dd, target_oe); 46 } 47 48 static void hfi1_setscl(void *data, int state) 49 { 50 struct hfi1_i2c_bus *bus = (struct hfi1_i2c_bus *)data; 51 struct hfi1_devdata *dd = bus->controlling_dd; 52 u64 reg; 53 u32 target_oe; 54 55 target_oe = i2c_oe_csr(bus->num); 56 reg = read_csr(dd, target_oe); 57 /* 58 * The OE bit value is inverted and connected to the pin. When 59 * OE is 0 the pin is left to be pulled up, when the OE is 1 60 * the pin is driven low. This matches the "open drain" or "open 61 * collector" convention. 62 */ 63 if (state) 64 reg &= ~QSFP_HFI0_I2CCLK; 65 else 66 reg |= QSFP_HFI0_I2CCLK; 67 write_csr(dd, target_oe, reg); 68 /* do a read to force the write into the chip */ 69 (void)read_csr(dd, target_oe); 70 } 71 72 static int hfi1_getsda(void *data) 73 { 74 struct hfi1_i2c_bus *bus = (struct hfi1_i2c_bus *)data; 75 u64 reg; 76 u32 target_in; 77 78 hfi1_setsda(data, 1); /* clear OE so we do not pull line down */ 79 udelay(2); /* 1us pull up + 250ns hold */ 80 81 target_in = i2c_in_csr(bus->num); 82 reg = read_csr(bus->controlling_dd, target_in); 83 return !!(reg & QSFP_HFI0_I2CDAT); 84 } 85 86 static int hfi1_getscl(void *data) 87 { 88 struct hfi1_i2c_bus *bus = (struct hfi1_i2c_bus *)data; 89 u64 reg; 90 u32 target_in; 91 92 hfi1_setscl(data, 1); /* clear OE so we do not pull line down */ 93 udelay(2); /* 1us pull up + 250ns hold */ 94 95 target_in = i2c_in_csr(bus->num); 96 reg = read_csr(bus->controlling_dd, target_in); 97 return !!(reg & QSFP_HFI0_I2CCLK); 98 } 99 100 /* 101 * Allocate and initialize the given i2c bus number. 102 * Returns NULL on failure. 103 */ 104 static struct hfi1_i2c_bus *init_i2c_bus(struct hfi1_devdata *dd, 105 struct hfi1_asic_data *ad, int num) 106 { 107 struct hfi1_i2c_bus *bus; 108 int ret; 109 110 bus = kzalloc(sizeof(*bus), GFP_KERNEL); 111 if (!bus) 112 return NULL; 113 114 bus->controlling_dd = dd; 115 bus->num = num; /* our bus number */ 116 117 bus->algo.setsda = hfi1_setsda; 118 bus->algo.setscl = hfi1_setscl; 119 bus->algo.getsda = hfi1_getsda; 120 bus->algo.getscl = hfi1_getscl; 121 bus->algo.udelay = 5; 122 bus->algo.timeout = usecs_to_jiffies(100000); 123 bus->algo.data = bus; 124 125 bus->adapter.owner = THIS_MODULE; 126 bus->adapter.algo_data = &bus->algo; 127 bus->adapter.dev.parent = &dd->pcidev->dev; 128 snprintf(bus->adapter.name, sizeof(bus->adapter.name), 129 "hfi1_i2c%d", num); 130 131 ret = i2c_bit_add_bus(&bus->adapter); 132 if (ret) { 133 dd_dev_info(dd, "%s: unable to add i2c bus %d, err %d\n", 134 __func__, num, ret); 135 kfree(bus); 136 return NULL; 137 } 138 139 return bus; 140 } 141 142 /* 143 * Initialize i2c buses. 144 * Return 0 on success, -errno on error. 145 */ 146 int set_up_i2c(struct hfi1_devdata *dd, struct hfi1_asic_data *ad) 147 { 148 ad->i2c_bus0 = init_i2c_bus(dd, ad, 0); 149 ad->i2c_bus1 = init_i2c_bus(dd, ad, 1); 150 if (!ad->i2c_bus0 || !ad->i2c_bus1) 151 return -ENOMEM; 152 return 0; 153 }; 154 155 static void clean_i2c_bus(struct hfi1_i2c_bus *bus) 156 { 157 if (bus) { 158 i2c_del_adapter(&bus->adapter); 159 kfree(bus); 160 } 161 } 162 163 void clean_up_i2c(struct hfi1_devdata *dd, struct hfi1_asic_data *ad) 164 { 165 if (!ad) 166 return; 167 clean_i2c_bus(ad->i2c_bus0); 168 ad->i2c_bus0 = NULL; 169 clean_i2c_bus(ad->i2c_bus1); 170 ad->i2c_bus1 = NULL; 171 } 172 173 static int i2c_bus_write(struct hfi1_devdata *dd, struct hfi1_i2c_bus *i2c, 174 u8 slave_addr, int offset, int offset_size, 175 u8 *data, u16 len) 176 { 177 int ret; 178 int num_msgs; 179 u8 offset_bytes[2]; 180 struct i2c_msg msgs[2]; 181 182 switch (offset_size) { 183 case 0: 184 num_msgs = 1; 185 msgs[0].addr = slave_addr; 186 msgs[0].flags = 0; 187 msgs[0].len = len; 188 msgs[0].buf = data; 189 break; 190 case 2: 191 offset_bytes[1] = (offset >> 8) & 0xff; 192 fallthrough; 193 case 1: 194 num_msgs = 2; 195 offset_bytes[0] = offset & 0xff; 196 197 msgs[0].addr = slave_addr; 198 msgs[0].flags = 0; 199 msgs[0].len = offset_size; 200 msgs[0].buf = offset_bytes; 201 202 msgs[1].addr = slave_addr; 203 msgs[1].flags = I2C_M_NOSTART; 204 msgs[1].len = len; 205 msgs[1].buf = data; 206 break; 207 default: 208 return -EINVAL; 209 } 210 211 i2c->controlling_dd = dd; 212 ret = i2c_transfer(&i2c->adapter, msgs, num_msgs); 213 if (ret != num_msgs) { 214 dd_dev_err(dd, "%s: bus %d, i2c slave 0x%x, offset 0x%x, len 0x%x; write failed, ret %d\n", 215 __func__, i2c->num, slave_addr, offset, len, ret); 216 return ret < 0 ? ret : -EIO; 217 } 218 return 0; 219 } 220 221 static int i2c_bus_read(struct hfi1_devdata *dd, struct hfi1_i2c_bus *bus, 222 u8 slave_addr, int offset, int offset_size, 223 u8 *data, u16 len) 224 { 225 int ret; 226 int num_msgs; 227 u8 offset_bytes[2]; 228 struct i2c_msg msgs[2]; 229 230 switch (offset_size) { 231 case 0: 232 num_msgs = 1; 233 msgs[0].addr = slave_addr; 234 msgs[0].flags = I2C_M_RD; 235 msgs[0].len = len; 236 msgs[0].buf = data; 237 break; 238 case 2: 239 offset_bytes[1] = (offset >> 8) & 0xff; 240 fallthrough; 241 case 1: 242 num_msgs = 2; 243 offset_bytes[0] = offset & 0xff; 244 245 msgs[0].addr = slave_addr; 246 msgs[0].flags = 0; 247 msgs[0].len = offset_size; 248 msgs[0].buf = offset_bytes; 249 250 msgs[1].addr = slave_addr; 251 msgs[1].flags = I2C_M_RD; 252 msgs[1].len = len; 253 msgs[1].buf = data; 254 break; 255 default: 256 return -EINVAL; 257 } 258 259 bus->controlling_dd = dd; 260 ret = i2c_transfer(&bus->adapter, msgs, num_msgs); 261 if (ret != num_msgs) { 262 dd_dev_err(dd, "%s: bus %d, i2c slave 0x%x, offset 0x%x, len 0x%x; read failed, ret %d\n", 263 __func__, bus->num, slave_addr, offset, len, ret); 264 return ret < 0 ? ret : -EIO; 265 } 266 return 0; 267 } 268 269 /* 270 * Raw i2c write. No set-up or lock checking. 271 * 272 * Return 0 on success, -errno on error. 273 */ 274 static int __i2c_write(struct hfi1_pportdata *ppd, u32 target, int i2c_addr, 275 int offset, void *bp, int len) 276 { 277 struct hfi1_devdata *dd = ppd->dd; 278 struct hfi1_i2c_bus *bus; 279 u8 slave_addr; 280 int offset_size; 281 282 bus = target ? dd->asic_data->i2c_bus1 : dd->asic_data->i2c_bus0; 283 slave_addr = (i2c_addr & 0xff) >> 1; /* convert to 7-bit addr */ 284 offset_size = (i2c_addr >> 8) & 0x3; 285 return i2c_bus_write(dd, bus, slave_addr, offset, offset_size, bp, len); 286 } 287 288 /* 289 * Caller must hold the i2c chain resource. 290 * 291 * Return number of bytes written, or -errno. 292 */ 293 int i2c_write(struct hfi1_pportdata *ppd, u32 target, int i2c_addr, int offset, 294 void *bp, int len) 295 { 296 int ret; 297 298 if (!check_chip_resource(ppd->dd, i2c_target(target), __func__)) 299 return -EACCES; 300 301 ret = __i2c_write(ppd, target, i2c_addr, offset, bp, len); 302 if (ret) 303 return ret; 304 305 return len; 306 } 307 308 /* 309 * Raw i2c read. No set-up or lock checking. 310 * 311 * Return 0 on success, -errno on error. 312 */ 313 static int __i2c_read(struct hfi1_pportdata *ppd, u32 target, int i2c_addr, 314 int offset, void *bp, int len) 315 { 316 struct hfi1_devdata *dd = ppd->dd; 317 struct hfi1_i2c_bus *bus; 318 u8 slave_addr; 319 int offset_size; 320 321 bus = target ? dd->asic_data->i2c_bus1 : dd->asic_data->i2c_bus0; 322 slave_addr = (i2c_addr & 0xff) >> 1; /* convert to 7-bit addr */ 323 offset_size = (i2c_addr >> 8) & 0x3; 324 return i2c_bus_read(dd, bus, slave_addr, offset, offset_size, bp, len); 325 } 326 327 /* 328 * Caller must hold the i2c chain resource. 329 * 330 * Return number of bytes read, or -errno. 331 */ 332 int i2c_read(struct hfi1_pportdata *ppd, u32 target, int i2c_addr, int offset, 333 void *bp, int len) 334 { 335 int ret; 336 337 if (!check_chip_resource(ppd->dd, i2c_target(target), __func__)) 338 return -EACCES; 339 340 ret = __i2c_read(ppd, target, i2c_addr, offset, bp, len); 341 if (ret) 342 return ret; 343 344 return len; 345 } 346 347 /* 348 * Write page n, offset m of QSFP memory as defined by SFF 8636 349 * by writing @addr = ((256 * n) + m) 350 * 351 * Caller must hold the i2c chain resource. 352 * 353 * Return number of bytes written or -errno. 354 */ 355 int qsfp_write(struct hfi1_pportdata *ppd, u32 target, int addr, void *bp, 356 int len) 357 { 358 int count = 0; 359 int offset; 360 int nwrite; 361 int ret = 0; 362 u8 page; 363 364 if (!check_chip_resource(ppd->dd, i2c_target(target), __func__)) 365 return -EACCES; 366 367 while (count < len) { 368 /* 369 * Set the qsfp page based on a zero-based address 370 * and a page size of QSFP_PAGESIZE bytes. 371 */ 372 page = (u8)(addr / QSFP_PAGESIZE); 373 374 ret = __i2c_write(ppd, target, QSFP_DEV | QSFP_OFFSET_SIZE, 375 QSFP_PAGE_SELECT_BYTE_OFFS, &page, 1); 376 /* QSFPs require a 5-10msec delay after write operations */ 377 mdelay(5); 378 if (ret) { 379 hfi1_dev_porterr(ppd->dd, ppd->port, 380 "QSFP chain %d can't write QSFP_PAGE_SELECT_BYTE: %d\n", 381 target, ret); 382 break; 383 } 384 385 offset = addr % QSFP_PAGESIZE; 386 nwrite = len - count; 387 /* truncate write to boundary if crossing boundary */ 388 if (((addr % QSFP_RW_BOUNDARY) + nwrite) > QSFP_RW_BOUNDARY) 389 nwrite = QSFP_RW_BOUNDARY - (addr % QSFP_RW_BOUNDARY); 390 391 ret = __i2c_write(ppd, target, QSFP_DEV | QSFP_OFFSET_SIZE, 392 offset, bp + count, nwrite); 393 /* QSFPs require a 5-10msec delay after write operations */ 394 mdelay(5); 395 if (ret) /* stop on error */ 396 break; 397 398 count += nwrite; 399 addr += nwrite; 400 } 401 402 if (ret < 0) 403 return ret; 404 return count; 405 } 406 407 /* 408 * Perform a stand-alone single QSFP write. Acquire the resource, do the 409 * write, then release the resource. 410 */ 411 int one_qsfp_write(struct hfi1_pportdata *ppd, u32 target, int addr, void *bp, 412 int len) 413 { 414 struct hfi1_devdata *dd = ppd->dd; 415 u32 resource = qsfp_resource(dd); 416 int ret; 417 418 ret = acquire_chip_resource(dd, resource, QSFP_WAIT); 419 if (ret) 420 return ret; 421 ret = qsfp_write(ppd, target, addr, bp, len); 422 release_chip_resource(dd, resource); 423 424 return ret; 425 } 426 427 /* 428 * Access page n, offset m of QSFP memory as defined by SFF 8636 429 * by reading @addr = ((256 * n) + m) 430 * 431 * Caller must hold the i2c chain resource. 432 * 433 * Return the number of bytes read or -errno. 434 */ 435 int qsfp_read(struct hfi1_pportdata *ppd, u32 target, int addr, void *bp, 436 int len) 437 { 438 int count = 0; 439 int offset; 440 int nread; 441 int ret = 0; 442 u8 page; 443 444 if (!check_chip_resource(ppd->dd, i2c_target(target), __func__)) 445 return -EACCES; 446 447 while (count < len) { 448 /* 449 * Set the qsfp page based on a zero-based address 450 * and a page size of QSFP_PAGESIZE bytes. 451 */ 452 page = (u8)(addr / QSFP_PAGESIZE); 453 ret = __i2c_write(ppd, target, QSFP_DEV | QSFP_OFFSET_SIZE, 454 QSFP_PAGE_SELECT_BYTE_OFFS, &page, 1); 455 /* QSFPs require a 5-10msec delay after write operations */ 456 mdelay(5); 457 if (ret) { 458 hfi1_dev_porterr(ppd->dd, ppd->port, 459 "QSFP chain %d can't write QSFP_PAGE_SELECT_BYTE: %d\n", 460 target, ret); 461 break; 462 } 463 464 offset = addr % QSFP_PAGESIZE; 465 nread = len - count; 466 /* truncate read to boundary if crossing boundary */ 467 if (((addr % QSFP_RW_BOUNDARY) + nread) > QSFP_RW_BOUNDARY) 468 nread = QSFP_RW_BOUNDARY - (addr % QSFP_RW_BOUNDARY); 469 470 ret = __i2c_read(ppd, target, QSFP_DEV | QSFP_OFFSET_SIZE, 471 offset, bp + count, nread); 472 if (ret) /* stop on error */ 473 break; 474 475 count += nread; 476 addr += nread; 477 } 478 479 if (ret < 0) 480 return ret; 481 return count; 482 } 483 484 /* 485 * Perform a stand-alone single QSFP read. Acquire the resource, do the 486 * read, then release the resource. 487 */ 488 int one_qsfp_read(struct hfi1_pportdata *ppd, u32 target, int addr, void *bp, 489 int len) 490 { 491 struct hfi1_devdata *dd = ppd->dd; 492 u32 resource = qsfp_resource(dd); 493 int ret; 494 495 ret = acquire_chip_resource(dd, resource, QSFP_WAIT); 496 if (ret) 497 return ret; 498 ret = qsfp_read(ppd, target, addr, bp, len); 499 release_chip_resource(dd, resource); 500 501 return ret; 502 } 503 504 /* 505 * This function caches the QSFP memory range in 128 byte chunks. 506 * As an example, the next byte after address 255 is byte 128 from 507 * upper page 01H (if existing) rather than byte 0 from lower page 00H. 508 * Access page n, offset m of QSFP memory as defined by SFF 8636 509 * in the cache by reading byte ((128 * n) + m) 510 * The calls to qsfp_{read,write} in this function correctly handle the 511 * address map difference between this mapping and the mapping implemented 512 * by those functions 513 * 514 * The caller must be holding the QSFP i2c chain resource. 515 */ 516 int refresh_qsfp_cache(struct hfi1_pportdata *ppd, struct qsfp_data *cp) 517 { 518 u32 target = ppd->dd->hfi1_id; 519 int ret; 520 unsigned long flags; 521 u8 *cache = &cp->cache[0]; 522 523 /* ensure sane contents on invalid reads, for cable swaps */ 524 memset(cache, 0, (QSFP_MAX_NUM_PAGES * 128)); 525 spin_lock_irqsave(&ppd->qsfp_info.qsfp_lock, flags); 526 ppd->qsfp_info.cache_valid = 0; 527 spin_unlock_irqrestore(&ppd->qsfp_info.qsfp_lock, flags); 528 529 if (!qsfp_mod_present(ppd)) { 530 ret = -ENODEV; 531 goto bail; 532 } 533 534 ret = qsfp_read(ppd, target, 0, cache, QSFP_PAGESIZE); 535 if (ret != QSFP_PAGESIZE) { 536 dd_dev_info(ppd->dd, 537 "%s: Page 0 read failed, expected %d, got %d\n", 538 __func__, QSFP_PAGESIZE, ret); 539 goto bail; 540 } 541 542 /* Is paging enabled? */ 543 if (!(cache[2] & 4)) { 544 /* Paging enabled, page 03 required */ 545 if ((cache[195] & 0xC0) == 0xC0) { 546 /* all */ 547 ret = qsfp_read(ppd, target, 384, cache + 256, 128); 548 if (ret <= 0 || ret != 128) { 549 dd_dev_info(ppd->dd, "%s failed\n", __func__); 550 goto bail; 551 } 552 ret = qsfp_read(ppd, target, 640, cache + 384, 128); 553 if (ret <= 0 || ret != 128) { 554 dd_dev_info(ppd->dd, "%s failed\n", __func__); 555 goto bail; 556 } 557 ret = qsfp_read(ppd, target, 896, cache + 512, 128); 558 if (ret <= 0 || ret != 128) { 559 dd_dev_info(ppd->dd, "%s failed\n", __func__); 560 goto bail; 561 } 562 } else if ((cache[195] & 0x80) == 0x80) { 563 /* only page 2 and 3 */ 564 ret = qsfp_read(ppd, target, 640, cache + 384, 128); 565 if (ret <= 0 || ret != 128) { 566 dd_dev_info(ppd->dd, "%s failed\n", __func__); 567 goto bail; 568 } 569 ret = qsfp_read(ppd, target, 896, cache + 512, 128); 570 if (ret <= 0 || ret != 128) { 571 dd_dev_info(ppd->dd, "%s failed\n", __func__); 572 goto bail; 573 } 574 } else if ((cache[195] & 0x40) == 0x40) { 575 /* only page 1 and 3 */ 576 ret = qsfp_read(ppd, target, 384, cache + 256, 128); 577 if (ret <= 0 || ret != 128) { 578 dd_dev_info(ppd->dd, "%s failed\n", __func__); 579 goto bail; 580 } 581 ret = qsfp_read(ppd, target, 896, cache + 512, 128); 582 if (ret <= 0 || ret != 128) { 583 dd_dev_info(ppd->dd, "%s failed\n", __func__); 584 goto bail; 585 } 586 } else { 587 /* only page 3 */ 588 ret = qsfp_read(ppd, target, 896, cache + 512, 128); 589 if (ret <= 0 || ret != 128) { 590 dd_dev_info(ppd->dd, "%s failed\n", __func__); 591 goto bail; 592 } 593 } 594 } 595 596 spin_lock_irqsave(&ppd->qsfp_info.qsfp_lock, flags); 597 ppd->qsfp_info.cache_valid = 1; 598 ppd->qsfp_info.cache_refresh_required = 0; 599 spin_unlock_irqrestore(&ppd->qsfp_info.qsfp_lock, flags); 600 601 return 0; 602 603 bail: 604 memset(cache, 0, (QSFP_MAX_NUM_PAGES * 128)); 605 return ret; 606 } 607 608 const char * const hfi1_qsfp_devtech[16] = { 609 "850nm VCSEL", "1310nm VCSEL", "1550nm VCSEL", "1310nm FP", 610 "1310nm DFB", "1550nm DFB", "1310nm EML", "1550nm EML", 611 "Cu Misc", "1490nm DFB", "Cu NoEq", "Cu Eq", 612 "Undef", "Cu Active BothEq", "Cu FarEq", "Cu NearEq" 613 }; 614 615 #define QSFP_DUMP_CHUNK 16 /* Holds longest string */ 616 #define QSFP_DEFAULT_HDR_CNT 224 617 618 #define QSFP_PWR(pbyte) (((pbyte) >> 6) & 3) 619 #define QSFP_HIGH_PWR(pbyte) ((pbyte) & 3) 620 /* For use with QSFP_HIGH_PWR macro */ 621 #define QSFP_HIGH_PWR_UNUSED 0 /* Bits [1:0] = 00 implies low power module */ 622 623 /* 624 * Takes power class byte [Page 00 Byte 129] in SFF 8636 625 * Returns power class as integer (1 through 7, per SFF 8636 rev 2.4) 626 */ 627 int get_qsfp_power_class(u8 power_byte) 628 { 629 if (QSFP_HIGH_PWR(power_byte) == QSFP_HIGH_PWR_UNUSED) 630 /* power classes count from 1, their bit encodings from 0 */ 631 return (QSFP_PWR(power_byte) + 1); 632 /* 633 * 00 in the high power classes stands for unused, bringing 634 * balance to the off-by-1 offset above, we add 4 here to 635 * account for the difference between the low and high power 636 * groups 637 */ 638 return (QSFP_HIGH_PWR(power_byte) + 4); 639 } 640 641 int qsfp_mod_present(struct hfi1_pportdata *ppd) 642 { 643 struct hfi1_devdata *dd = ppd->dd; 644 u64 reg; 645 646 reg = read_csr(dd, dd->hfi1_id ? ASIC_QSFP2_IN : ASIC_QSFP1_IN); 647 return !(reg & QSFP_HFI0_MODPRST_N); 648 } 649 650 /* 651 * This function maps QSFP memory addresses in 128 byte chunks in the following 652 * fashion per the CableInfo SMA query definition in the IBA 1.3 spec/OPA Gen 1 653 * spec 654 * For addr 000-127, lower page 00h 655 * For addr 128-255, upper page 00h 656 * For addr 256-383, upper page 01h 657 * For addr 384-511, upper page 02h 658 * For addr 512-639, upper page 03h 659 * 660 * For addresses beyond this range, it returns the invalid range of data buffer 661 * set to 0. 662 * For upper pages that are optional, if they are not valid, returns the 663 * particular range of bytes in the data buffer set to 0. 664 */ 665 int get_cable_info(struct hfi1_devdata *dd, u32 port_num, u32 addr, u32 len, 666 u8 *data) 667 { 668 struct hfi1_pportdata *ppd; 669 u32 excess_len = len; 670 int ret = 0, offset = 0; 671 672 if (port_num > dd->num_pports || port_num < 1) { 673 dd_dev_info(dd, "%s: Invalid port number %d\n", 674 __func__, port_num); 675 ret = -EINVAL; 676 goto set_zeroes; 677 } 678 679 ppd = dd->pport + (port_num - 1); 680 if (!qsfp_mod_present(ppd)) { 681 ret = -ENODEV; 682 goto set_zeroes; 683 } 684 685 if (!ppd->qsfp_info.cache_valid) { 686 ret = -EINVAL; 687 goto set_zeroes; 688 } 689 690 if (addr >= (QSFP_MAX_NUM_PAGES * 128)) { 691 ret = -ERANGE; 692 goto set_zeroes; 693 } 694 695 if ((addr + len) > (QSFP_MAX_NUM_PAGES * 128)) { 696 excess_len = (addr + len) - (QSFP_MAX_NUM_PAGES * 128); 697 memcpy(data, &ppd->qsfp_info.cache[addr], (len - excess_len)); 698 data += (len - excess_len); 699 goto set_zeroes; 700 } 701 702 memcpy(data, &ppd->qsfp_info.cache[addr], len); 703 704 if (addr <= QSFP_MONITOR_VAL_END && 705 (addr + len) >= QSFP_MONITOR_VAL_START) { 706 /* Overlap with the dynamic channel monitor range */ 707 if (addr < QSFP_MONITOR_VAL_START) { 708 if (addr + len <= QSFP_MONITOR_VAL_END) 709 len = addr + len - QSFP_MONITOR_VAL_START; 710 else 711 len = QSFP_MONITOR_RANGE; 712 offset = QSFP_MONITOR_VAL_START - addr; 713 addr = QSFP_MONITOR_VAL_START; 714 } else if (addr == QSFP_MONITOR_VAL_START) { 715 offset = 0; 716 if (addr + len > QSFP_MONITOR_VAL_END) 717 len = QSFP_MONITOR_RANGE; 718 } else { 719 offset = 0; 720 if (addr + len > QSFP_MONITOR_VAL_END) 721 len = QSFP_MONITOR_VAL_END - addr + 1; 722 } 723 /* Refresh the values of the dynamic monitors from the cable */ 724 ret = one_qsfp_read(ppd, dd->hfi1_id, addr, data + offset, len); 725 if (ret != len) { 726 ret = -EAGAIN; 727 goto set_zeroes; 728 } 729 } 730 731 return 0; 732 733 set_zeroes: 734 memset(data, 0, excess_len); 735 return ret; 736 } 737 738 static const char *pwr_codes[8] = {"N/AW", 739 "1.5W", 740 "2.0W", 741 "2.5W", 742 "3.5W", 743 "4.0W", 744 "4.5W", 745 "5.0W" 746 }; 747 748 int qsfp_dump(struct hfi1_pportdata *ppd, char *buf, int len) 749 { 750 u8 *cache = &ppd->qsfp_info.cache[0]; 751 u8 bin_buff[QSFP_DUMP_CHUNK]; 752 char lenstr[6]; 753 int sofar; 754 int bidx = 0; 755 u8 *atten = &cache[QSFP_ATTEN_OFFS]; 756 u8 *vendor_oui = &cache[QSFP_VOUI_OFFS]; 757 u8 power_byte = 0; 758 759 sofar = 0; 760 lenstr[0] = ' '; 761 lenstr[1] = '\0'; 762 763 if (ppd->qsfp_info.cache_valid) { 764 if (QSFP_IS_CU(cache[QSFP_MOD_TECH_OFFS])) 765 snprintf(lenstr, sizeof(lenstr), "%dM ", 766 cache[QSFP_MOD_LEN_OFFS]); 767 768 power_byte = cache[QSFP_MOD_PWR_OFFS]; 769 sofar += scnprintf(buf + sofar, len - sofar, "PWR:%.3sW\n", 770 pwr_codes[get_qsfp_power_class(power_byte)]); 771 772 sofar += scnprintf(buf + sofar, len - sofar, "TECH:%s%s\n", 773 lenstr, 774 hfi1_qsfp_devtech[(cache[QSFP_MOD_TECH_OFFS]) >> 4]); 775 776 sofar += scnprintf(buf + sofar, len - sofar, "Vendor:%.*s\n", 777 QSFP_VEND_LEN, &cache[QSFP_VEND_OFFS]); 778 779 sofar += scnprintf(buf + sofar, len - sofar, "OUI:%06X\n", 780 QSFP_OUI(vendor_oui)); 781 782 sofar += scnprintf(buf + sofar, len - sofar, "Part#:%.*s\n", 783 QSFP_PN_LEN, &cache[QSFP_PN_OFFS]); 784 785 sofar += scnprintf(buf + sofar, len - sofar, "Rev:%.*s\n", 786 QSFP_REV_LEN, &cache[QSFP_REV_OFFS]); 787 788 if (QSFP_IS_CU(cache[QSFP_MOD_TECH_OFFS])) 789 sofar += scnprintf(buf + sofar, len - sofar, 790 "Atten:%d, %d\n", 791 QSFP_ATTEN_SDR(atten), 792 QSFP_ATTEN_DDR(atten)); 793 794 sofar += scnprintf(buf + sofar, len - sofar, "Serial:%.*s\n", 795 QSFP_SN_LEN, &cache[QSFP_SN_OFFS]); 796 797 sofar += scnprintf(buf + sofar, len - sofar, "Date:%.*s\n", 798 QSFP_DATE_LEN, &cache[QSFP_DATE_OFFS]); 799 800 sofar += scnprintf(buf + sofar, len - sofar, "Lot:%.*s\n", 801 QSFP_LOT_LEN, &cache[QSFP_LOT_OFFS]); 802 803 while (bidx < QSFP_DEFAULT_HDR_CNT) { 804 int iidx; 805 806 memcpy(bin_buff, &cache[bidx], QSFP_DUMP_CHUNK); 807 for (iidx = 0; iidx < QSFP_DUMP_CHUNK; ++iidx) { 808 sofar += scnprintf(buf + sofar, len - sofar, 809 " %02X", bin_buff[iidx]); 810 } 811 sofar += scnprintf(buf + sofar, len - sofar, "\n"); 812 bidx += QSFP_DUMP_CHUNK; 813 } 814 } 815 return sofar; 816 } 817