1 /* SPDX-License-Identifier: GPL-2.0-only */ 2 /* 3 * Copyright (C) 2012 Invensense, Inc. 4 */ 5 6 #ifndef INV_MPU_IIO_H_ 7 #define INV_MPU_IIO_H_ 8 9 #include <linux/i2c.h> 10 #include <linux/i2c-mux.h> 11 #include <linux/mutex.h> 12 #include <linux/platform_data/invensense_mpu6050.h> 13 #include <linux/regmap.h> 14 15 #include <linux/iio/buffer.h> 16 #include <linux/iio/common/inv_sensors_timestamp.h> 17 #include <linux/iio/iio.h> 18 #include <linux/iio/kfifo_buf.h> 19 #include <linux/iio/trigger.h> 20 #include <linux/iio/triggered_buffer.h> 21 #include <linux/iio/trigger_consumer.h> 22 #include <linux/iio/sysfs.h> 23 24 /** 25 * struct inv_mpu6050_reg_map - Notable registers. 26 * @sample_rate_div: Divider applied to gyro output rate. 27 * @lpf: Configures internal low pass filter. 28 * @accel_lpf: Configures accelerometer low pass filter. 29 * @user_ctrl: Enables/resets the FIFO. 30 * @fifo_en: Determines which data will appear in FIFO. 31 * @gyro_config: gyro config register. 32 * @accl_config: accel config register 33 * @fifo_count_h: Upper byte of FIFO count. 34 * @fifo_r_w: FIFO register. 35 * @raw_gyro: Address of first gyro register. 36 * @raw_accl: Address of first accel register. 37 * @temperature: temperature register 38 * @int_enable: Interrupt enable register. 39 * @int_status: Interrupt status register. 40 * @pwr_mgmt_1: Controls chip's power state and clock source. 41 * @pwr_mgmt_2: Controls power state of individual sensors. 42 * @int_pin_cfg; Controls interrupt pin configuration. 43 * @accl_offset: Controls the accelerometer calibration offset. 44 * @gyro_offset: Controls the gyroscope calibration offset. 45 * @i2c_if: Controls the i2c interface 46 */ 47 struct inv_mpu6050_reg_map { 48 u8 sample_rate_div; 49 u8 lpf; 50 u8 accel_lpf; 51 u8 user_ctrl; 52 u8 fifo_en; 53 u8 gyro_config; 54 u8 accl_config; 55 u8 fifo_count_h; 56 u8 fifo_r_w; 57 u8 raw_gyro; 58 u8 raw_accl; 59 u8 temperature; 60 u8 int_enable; 61 u8 int_status; 62 u8 pwr_mgmt_1; 63 u8 pwr_mgmt_2; 64 u8 int_pin_cfg; 65 u8 accl_offset; 66 u8 gyro_offset; 67 u8 i2c_if; 68 }; 69 70 /*device enum */ 71 enum inv_devices { 72 INV_MPU6050, 73 INV_MPU6500, 74 INV_MPU6515, 75 INV_MPU6880, 76 INV_MPU6000, 77 INV_MPU9150, 78 INV_MPU9250, 79 INV_MPU9255, 80 INV_ICM20608, 81 INV_ICM20608D, 82 INV_ICM20609, 83 INV_ICM20689, 84 INV_ICM20600, 85 INV_ICM20602, 86 INV_ICM20690, 87 INV_IAM20680, 88 INV_NUM_PARTS 89 }; 90 91 /* chip sensors mask: accelerometer, gyroscope, temperature, magnetometer */ 92 #define INV_MPU6050_SENSOR_ACCL BIT(0) 93 #define INV_MPU6050_SENSOR_GYRO BIT(1) 94 #define INV_MPU6050_SENSOR_TEMP BIT(2) 95 #define INV_MPU6050_SENSOR_MAGN BIT(3) 96 97 /** 98 * struct inv_mpu6050_chip_config - Cached chip configuration data. 99 * @clk: selected chip clock 100 * @fsr: Full scale range. 101 * @lpf: Digital low pass filter frequency. 102 * @accl_fs: accel full scale range. 103 * @accl_en: accel engine enabled 104 * @gyro_en: gyro engine enabled 105 * @temp_en: temperature sensor enabled 106 * @magn_en: magn engine (i2c master) enabled 107 * @accl_fifo_enable: enable accel data output 108 * @gyro_fifo_enable: enable gyro data output 109 * @temp_fifo_enable: enable temp data output 110 * @magn_fifo_enable: enable magn data output 111 * @divider: chip sample rate divider (sample rate divider - 1) 112 */ 113 struct inv_mpu6050_chip_config { 114 unsigned int clk:3; 115 unsigned int fsr:2; 116 unsigned int lpf:3; 117 unsigned int accl_fs:2; 118 unsigned int accl_en:1; 119 unsigned int gyro_en:1; 120 unsigned int temp_en:1; 121 unsigned int magn_en:1; 122 unsigned int accl_fifo_enable:1; 123 unsigned int gyro_fifo_enable:1; 124 unsigned int temp_fifo_enable:1; 125 unsigned int magn_fifo_enable:1; 126 u8 divider; 127 u8 user_ctrl; 128 }; 129 130 /* 131 * Maximum of 6 + 6 + 2 + 7 (for MPU9x50) = 21 round up to 24 and plus 8. 132 * May be less if fewer channels are enabled, as long as the timestamp 133 * remains 8 byte aligned 134 */ 135 #define INV_MPU6050_OUTPUT_DATA_SIZE 32 136 137 /** 138 * struct inv_mpu6050_hw - Other important hardware information. 139 * @whoami: Self identification byte from WHO_AM_I register 140 * @name: name of the chip. 141 * @reg: register map of the chip. 142 * @config: configuration of the chip. 143 * @fifo_size: size of the FIFO in bytes. 144 * @temp: offset and scale to apply to raw temperature. 145 */ 146 struct inv_mpu6050_hw { 147 u8 whoami; 148 u8 *name; 149 const struct inv_mpu6050_reg_map *reg; 150 const struct inv_mpu6050_chip_config *config; 151 size_t fifo_size; 152 struct { 153 int offset; 154 int scale; 155 } temp; 156 struct { 157 unsigned int accel; 158 unsigned int gyro; 159 } startup_time; 160 }; 161 162 /* 163 * struct inv_mpu6050_state - Driver state variables. 164 * @lock: Chip access lock. 165 * @trig: IIO trigger. 166 * @chip_config: Cached attribute information. 167 * @reg: Map of important registers. 168 * @hw: Other hardware-specific information. 169 * @chip_type: chip type. 170 * @plat_data: platform data (deprecated in favor of @orientation). 171 * @orientation: sensor chip orientation relative to main hardware. 172 * @map regmap pointer. 173 * @irq interrupt number. 174 * @irq_mask the int_pin_cfg mask to configure interrupt type. 175 * @timestamp: timestamping module 176 * @vdd_supply: VDD voltage regulator for the chip. 177 * @vddio_supply I/O voltage regulator for the chip. 178 * @magn_disabled: magnetometer disabled for backward compatibility reason. 179 * @magn_raw_to_gauss: coefficient to convert mag raw value to Gauss. 180 * @magn_orient: magnetometer sensor chip orientation if available. 181 * @suspended_sensors: sensors mask of sensors turned off for suspend 182 * @data: read buffer used for bulk reads. 183 */ 184 struct inv_mpu6050_state { 185 struct mutex lock; 186 struct iio_trigger *trig; 187 struct inv_mpu6050_chip_config chip_config; 188 const struct inv_mpu6050_reg_map *reg; 189 const struct inv_mpu6050_hw *hw; 190 enum inv_devices chip_type; 191 struct i2c_mux_core *muxc; 192 struct i2c_client *mux_client; 193 struct inv_mpu6050_platform_data plat_data; 194 struct iio_mount_matrix orientation; 195 struct regmap *map; 196 int irq; 197 u8 irq_mask; 198 unsigned skip_samples; 199 struct inv_sensors_timestamp timestamp; 200 struct regulator *vdd_supply; 201 struct regulator *vddio_supply; 202 bool magn_disabled; 203 s32 magn_raw_to_gauss[3]; 204 struct iio_mount_matrix magn_orient; 205 unsigned int suspended_sensors; 206 bool level_shifter; 207 u8 *data; 208 }; 209 210 /*register and associated bit definition*/ 211 #define INV_MPU6050_REG_ACCEL_OFFSET 0x06 212 #define INV_MPU6050_REG_GYRO_OFFSET 0x13 213 214 #define INV_MPU6050_REG_SAMPLE_RATE_DIV 0x19 215 #define INV_MPU6050_REG_CONFIG 0x1A 216 #define INV_MPU6050_REG_GYRO_CONFIG 0x1B 217 #define INV_MPU6050_REG_ACCEL_CONFIG 0x1C 218 219 #define INV_MPU6050_REG_FIFO_EN 0x23 220 #define INV_MPU6050_BIT_SLAVE_0 0x01 221 #define INV_MPU6050_BIT_SLAVE_1 0x02 222 #define INV_MPU6050_BIT_SLAVE_2 0x04 223 #define INV_MPU6050_BIT_ACCEL_OUT 0x08 224 #define INV_MPU6050_BITS_GYRO_OUT 0x70 225 #define INV_MPU6050_BIT_TEMP_OUT 0x80 226 227 #define INV_MPU6050_REG_I2C_MST_CTRL 0x24 228 #define INV_MPU6050_BITS_I2C_MST_CLK_400KHZ 0x0D 229 #define INV_MPU6050_BIT_I2C_MST_P_NSR 0x10 230 #define INV_MPU6050_BIT_SLV3_FIFO_EN 0x20 231 #define INV_MPU6050_BIT_WAIT_FOR_ES 0x40 232 #define INV_MPU6050_BIT_MULT_MST_EN 0x80 233 234 /* control I2C slaves from 0 to 3 */ 235 #define INV_MPU6050_REG_I2C_SLV_ADDR(_x) (0x25 + 3 * (_x)) 236 #define INV_MPU6050_BIT_I2C_SLV_RNW 0x80 237 238 #define INV_MPU6050_REG_I2C_SLV_REG(_x) (0x26 + 3 * (_x)) 239 240 #define INV_MPU6050_REG_I2C_SLV_CTRL(_x) (0x27 + 3 * (_x)) 241 #define INV_MPU6050_BIT_SLV_GRP 0x10 242 #define INV_MPU6050_BIT_SLV_REG_DIS 0x20 243 #define INV_MPU6050_BIT_SLV_BYTE_SW 0x40 244 #define INV_MPU6050_BIT_SLV_EN 0x80 245 246 /* I2C master delay register */ 247 #define INV_MPU6050_REG_I2C_SLV4_CTRL 0x34 248 #define INV_MPU6050_BITS_I2C_MST_DLY(_x) ((_x) & 0x1F) 249 250 #define INV_MPU6050_REG_I2C_MST_STATUS 0x36 251 #define INV_MPU6050_BIT_I2C_SLV0_NACK 0x01 252 #define INV_MPU6050_BIT_I2C_SLV1_NACK 0x02 253 #define INV_MPU6050_BIT_I2C_SLV2_NACK 0x04 254 #define INV_MPU6050_BIT_I2C_SLV3_NACK 0x08 255 256 #define INV_MPU6050_REG_INT_ENABLE 0x38 257 #define INV_MPU6050_BIT_DATA_RDY_EN 0x01 258 #define INV_MPU6050_BIT_DMP_INT_EN 0x02 259 260 #define INV_MPU6050_REG_RAW_ACCEL 0x3B 261 #define INV_MPU6050_REG_TEMPERATURE 0x41 262 #define INV_MPU6050_REG_RAW_GYRO 0x43 263 264 #define INV_MPU6050_REG_INT_STATUS 0x3A 265 #define INV_MPU6050_BIT_FIFO_OVERFLOW_INT 0x10 266 #define INV_MPU6050_BIT_RAW_DATA_RDY_INT 0x01 267 268 #define INV_MPU6050_REG_EXT_SENS_DATA 0x49 269 270 /* I2C slaves data output from 0 to 3 */ 271 #define INV_MPU6050_REG_I2C_SLV_DO(_x) (0x63 + (_x)) 272 273 #define INV_MPU6050_REG_I2C_MST_DELAY_CTRL 0x67 274 #define INV_MPU6050_BIT_I2C_SLV0_DLY_EN 0x01 275 #define INV_MPU6050_BIT_I2C_SLV1_DLY_EN 0x02 276 #define INV_MPU6050_BIT_I2C_SLV2_DLY_EN 0x04 277 #define INV_MPU6050_BIT_I2C_SLV3_DLY_EN 0x08 278 #define INV_MPU6050_BIT_DELAY_ES_SHADOW 0x80 279 280 #define INV_MPU6050_REG_SIGNAL_PATH_RESET 0x68 281 #define INV_MPU6050_BIT_TEMP_RST BIT(0) 282 #define INV_MPU6050_BIT_ACCEL_RST BIT(1) 283 #define INV_MPU6050_BIT_GYRO_RST BIT(2) 284 285 #define INV_MPU6050_REG_USER_CTRL 0x6A 286 #define INV_MPU6050_BIT_SIG_COND_RST 0x01 287 #define INV_MPU6050_BIT_FIFO_RST 0x04 288 #define INV_MPU6050_BIT_DMP_RST 0x08 289 #define INV_MPU6050_BIT_I2C_MST_EN 0x20 290 #define INV_MPU6050_BIT_FIFO_EN 0x40 291 #define INV_MPU6050_BIT_DMP_EN 0x80 292 #define INV_MPU6050_BIT_I2C_IF_DIS 0x10 293 294 #define INV_MPU6050_REG_PWR_MGMT_1 0x6B 295 #define INV_MPU6050_BIT_H_RESET 0x80 296 #define INV_MPU6050_BIT_SLEEP 0x40 297 #define INV_MPU6050_BIT_TEMP_DIS 0x08 298 #define INV_MPU6050_BIT_CLK_MASK 0x7 299 300 #define INV_MPU6050_REG_PWR_MGMT_2 0x6C 301 #define INV_MPU6050_BIT_PWR_ACCL_STBY 0x38 302 #define INV_MPU6050_BIT_PWR_GYRO_STBY 0x07 303 304 /* ICM20602 register */ 305 #define INV_ICM20602_REG_I2C_IF 0x70 306 #define INV_ICM20602_BIT_I2C_IF_DIS 0x40 307 308 #define INV_MPU6050_REG_FIFO_COUNT_H 0x72 309 #define INV_MPU6050_REG_FIFO_R_W 0x74 310 311 #define INV_MPU6050_BYTES_PER_3AXIS_SENSOR 6 312 #define INV_MPU6050_FIFO_COUNT_BYTE 2 313 314 /* MPU9X50 9-axis magnetometer */ 315 #define INV_MPU9X50_BYTES_MAGN 7 316 317 /* FIFO temperature sample size */ 318 #define INV_MPU6050_BYTES_PER_TEMP_SENSOR 2 319 320 /* mpu6500 registers */ 321 #define INV_MPU6500_REG_ACCEL_CONFIG_2 0x1D 322 #define INV_ICM20689_BITS_FIFO_SIZE_MAX 0xC0 323 #define INV_MPU6500_REG_ACCEL_OFFSET 0x77 324 325 /* delay time in milliseconds */ 326 #define INV_MPU6050_POWER_UP_TIME 100 327 #define INV_MPU6050_TEMP_UP_TIME 100 328 #define INV_MPU6050_ACCEL_STARTUP_TIME 20 329 #define INV_MPU6050_GYRO_STARTUP_TIME 60 330 #define INV_MPU6050_GYRO_DOWN_TIME 150 331 #define INV_MPU6050_SUSPEND_DELAY_MS 2000 332 333 #define INV_MPU6500_GYRO_STARTUP_TIME 70 334 #define INV_MPU6500_ACCEL_STARTUP_TIME 30 335 336 #define INV_ICM20602_GYRO_STARTUP_TIME 100 337 #define INV_ICM20602_ACCEL_STARTUP_TIME 20 338 339 #define INV_ICM20690_GYRO_STARTUP_TIME 80 340 #define INV_ICM20690_ACCEL_STARTUP_TIME 10 341 342 343 /* delay time in microseconds */ 344 #define INV_MPU6050_REG_UP_TIME_MIN 5000 345 #define INV_MPU6050_REG_UP_TIME_MAX 10000 346 347 #define INV_MPU6050_TEMP_OFFSET 12420 348 #define INV_MPU6050_TEMP_SCALE 2941176 349 #define INV_MPU6050_MAX_GYRO_FS_PARAM 3 350 #define INV_MPU6050_MAX_ACCL_FS_PARAM 3 351 #define INV_MPU6050_THREE_AXIS 3 352 #define INV_MPU6050_GYRO_CONFIG_FSR_SHIFT 3 353 #define INV_ICM20690_GYRO_CONFIG_FSR_SHIFT 2 354 #define INV_MPU6050_ACCL_CONFIG_FSR_SHIFT 3 355 356 #define INV_MPU6500_TEMP_OFFSET 7011 357 #define INV_MPU6500_TEMP_SCALE 2995178 358 359 #define INV_ICM20608_TEMP_OFFSET 8170 360 #define INV_ICM20608_TEMP_SCALE 3059976 361 362 #define INV_MPU6050_REG_INT_PIN_CFG 0x37 363 #define INV_MPU6050_ACTIVE_HIGH 0x00 364 #define INV_MPU6050_ACTIVE_LOW 0x80 365 /* enable level triggering */ 366 #define INV_MPU6050_LATCH_INT_EN 0x20 367 #define INV_MPU6050_BIT_BYPASS_EN 0x2 368 369 /* Allowed timestamp period jitter in percent */ 370 #define INV_MPU6050_TS_PERIOD_JITTER 4 371 372 /* init parameters */ 373 #define INV_MPU6050_MAX_FIFO_RATE 1000 374 #define INV_MPU6050_MIN_FIFO_RATE 4 375 376 /* chip internal frequency: 1KHz */ 377 #define INV_MPU6050_INTERNAL_FREQ_HZ 1000 378 /* return the frequency divider (chip sample rate divider + 1) */ 379 #define INV_MPU6050_FREQ_DIVIDER(st) \ 380 ((st)->chip_config.divider + 1) 381 /* chip sample rate divider to fifo rate */ 382 #define INV_MPU6050_FIFO_RATE_TO_DIVIDER(fifo_rate) \ 383 ((INV_MPU6050_INTERNAL_FREQ_HZ / (fifo_rate)) - 1) 384 #define INV_MPU6050_DIVIDER_TO_FIFO_RATE(divider) \ 385 (INV_MPU6050_INTERNAL_FREQ_HZ / ((divider) + 1)) 386 387 #define INV_MPU6050_REG_WHOAMI 117 388 389 #define INV_MPU6000_WHOAMI_VALUE 0x68 390 #define INV_MPU6050_WHOAMI_VALUE 0x68 391 #define INV_MPU6500_WHOAMI_VALUE 0x70 392 #define INV_MPU6880_WHOAMI_VALUE 0x78 393 #define INV_MPU9150_WHOAMI_VALUE 0x68 394 #define INV_MPU9250_WHOAMI_VALUE 0x71 395 #define INV_MPU9255_WHOAMI_VALUE 0x73 396 #define INV_MPU6515_WHOAMI_VALUE 0x74 397 #define INV_ICM20608_WHOAMI_VALUE 0xAF 398 #define INV_ICM20608D_WHOAMI_VALUE 0xAE 399 #define INV_ICM20609_WHOAMI_VALUE 0xA6 400 #define INV_ICM20689_WHOAMI_VALUE 0x98 401 #define INV_ICM20600_WHOAMI_VALUE 0x11 402 #define INV_ICM20602_WHOAMI_VALUE 0x12 403 #define INV_ICM20690_WHOAMI_VALUE 0x20 404 #define INV_IAM20680_WHOAMI_VALUE 0xA9 405 406 /* scan element definition for generic MPU6xxx devices */ 407 enum inv_mpu6050_scan { 408 INV_MPU6050_SCAN_ACCL_X, 409 INV_MPU6050_SCAN_ACCL_Y, 410 INV_MPU6050_SCAN_ACCL_Z, 411 INV_MPU6050_SCAN_TEMP, 412 INV_MPU6050_SCAN_GYRO_X, 413 INV_MPU6050_SCAN_GYRO_Y, 414 INV_MPU6050_SCAN_GYRO_Z, 415 INV_MPU6050_SCAN_TIMESTAMP, 416 417 INV_MPU9X50_SCAN_MAGN_X = INV_MPU6050_SCAN_GYRO_Z + 1, 418 INV_MPU9X50_SCAN_MAGN_Y, 419 INV_MPU9X50_SCAN_MAGN_Z, 420 INV_MPU9X50_SCAN_TIMESTAMP, 421 }; 422 423 enum inv_mpu6050_filter_e { 424 INV_MPU6050_FILTER_NOLPF2 = 0, 425 INV_MPU6050_FILTER_200HZ, 426 INV_MPU6050_FILTER_100HZ, 427 INV_MPU6050_FILTER_45HZ, 428 INV_MPU6050_FILTER_20HZ, 429 INV_MPU6050_FILTER_10HZ, 430 INV_MPU6050_FILTER_5HZ, 431 INV_MPU6050_FILTER_NOLPF, 432 NUM_MPU6050_FILTER 433 }; 434 435 /* IIO attribute address */ 436 enum INV_MPU6050_IIO_ATTR_ADDR { 437 ATTR_GYRO_MATRIX, 438 ATTR_ACCL_MATRIX, 439 }; 440 441 enum inv_mpu6050_accl_fs_e { 442 INV_MPU6050_FS_02G = 0, 443 INV_MPU6050_FS_04G, 444 INV_MPU6050_FS_08G, 445 INV_MPU6050_FS_16G, 446 NUM_ACCL_FSR 447 }; 448 449 enum inv_mpu6050_fsr_e { 450 INV_MPU6050_FSR_250DPS = 0, 451 INV_MPU6050_FSR_500DPS, 452 INV_MPU6050_FSR_1000DPS, 453 INV_MPU6050_FSR_2000DPS, 454 NUM_MPU6050_FSR 455 }; 456 457 enum inv_mpu6050_clock_sel_e { 458 INV_CLK_INTERNAL = 0, 459 INV_CLK_PLL, 460 NUM_CLK 461 }; 462 463 irqreturn_t inv_mpu6050_read_fifo(int irq, void *p); 464 int inv_mpu6050_probe_trigger(struct iio_dev *indio_dev, int irq_type); 465 int inv_mpu6050_prepare_fifo(struct inv_mpu6050_state *st, bool enable); 466 int inv_mpu6050_switch_engine(struct inv_mpu6050_state *st, bool en, 467 unsigned int mask); 468 int inv_mpu_acpi_create_mux_client(struct i2c_client *client); 469 void inv_mpu_acpi_delete_mux_client(struct i2c_client *client); 470 int inv_mpu_core_probe(struct regmap *regmap, int irq, const char *name, 471 int (*inv_mpu_bus_setup)(struct iio_dev *), int chip_type); 472 extern const struct dev_pm_ops inv_mpu_pmops; 473 474 #endif 475