1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Texas Instruments TSC2046 SPI ADC driver 4 * 5 * Copyright (c) 2021 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix 6 */ 7 8 #include <linux/bitfield.h> 9 #include <linux/delay.h> 10 #include <linux/module.h> 11 #include <linux/regulator/consumer.h> 12 #include <linux/spi/spi.h> 13 #include <linux/units.h> 14 15 #include <asm/unaligned.h> 16 17 #include <linux/iio/buffer.h> 18 #include <linux/iio/trigger_consumer.h> 19 #include <linux/iio/triggered_buffer.h> 20 #include <linux/iio/trigger.h> 21 22 /* 23 * The PENIRQ of TSC2046 controller is implemented as level shifter attached to 24 * the X+ line. If voltage of the X+ line reaches a specific level the IRQ will 25 * be activated or deactivated. 26 * To make this kind of IRQ reusable as trigger following additions were 27 * implemented: 28 * - rate limiting: 29 * For typical touchscreen use case, we need to trigger about each 10ms. 30 * - hrtimer: 31 * Continue triggering at least once after the IRQ was deactivated. Then 32 * deactivate this trigger to stop sampling in order to reduce power 33 * consumption. 34 */ 35 36 #define TI_TSC2046_NAME "tsc2046" 37 38 /* This driver doesn't aim at the peak continuous sample rate */ 39 #define TI_TSC2046_MAX_SAMPLE_RATE 125000 40 #define TI_TSC2046_SAMPLE_BITS \ 41 BITS_PER_TYPE(struct tsc2046_adc_atom) 42 #define TI_TSC2046_MAX_CLK_FREQ \ 43 (TI_TSC2046_MAX_SAMPLE_RATE * TI_TSC2046_SAMPLE_BITS) 44 45 #define TI_TSC2046_SAMPLE_INTERVAL_US 10000 46 47 #define TI_TSC2046_START BIT(7) 48 #define TI_TSC2046_ADDR GENMASK(6, 4) 49 #define TI_TSC2046_ADDR_TEMP1 7 50 #define TI_TSC2046_ADDR_AUX 6 51 #define TI_TSC2046_ADDR_X 5 52 #define TI_TSC2046_ADDR_Z2 4 53 #define TI_TSC2046_ADDR_Z1 3 54 #define TI_TSC2046_ADDR_VBAT 2 55 #define TI_TSC2046_ADDR_Y 1 56 #define TI_TSC2046_ADDR_TEMP0 0 57 58 /* 59 * The mode bit sets the resolution of the ADC. With this bit low, the next 60 * conversion has 12-bit resolution, whereas with this bit high, the next 61 * conversion has 8-bit resolution. This driver is optimized for 12-bit mode. 62 * So, for this driver, this bit should stay zero. 63 */ 64 #define TI_TSC2046_8BIT_MODE BIT(3) 65 66 /* 67 * SER/DFR - The SER/DFR bit controls the reference mode, either single-ended 68 * (high) or differential (low). 69 */ 70 #define TI_TSC2046_SER BIT(2) 71 72 /* 73 * If VREF_ON and ADC_ON are both zero, then the chip operates in 74 * auto-wake/suspend mode. In most case this bits should stay zero. 75 */ 76 #define TI_TSC2046_PD1_VREF_ON BIT(1) 77 #define TI_TSC2046_PD0_ADC_ON BIT(0) 78 79 /* 80 * All supported devices can do 8 or 12bit resolution. This driver 81 * supports only 12bit mode, here we have a 16bit data transfer, where 82 * the MSB and the 3 LSB are 0. 83 */ 84 #define TI_TSC2046_DATA_12BIT GENMASK(14, 3) 85 86 #define TI_TSC2046_MAX_CHAN 8 87 #define TI_TSC2046_MIN_POLL_CNT 3 88 #define TI_TSC2046_EXT_POLL_CNT 3 89 #define TI_TSC2046_POLL_CNT \ 90 (TI_TSC2046_MIN_POLL_CNT + TI_TSC2046_EXT_POLL_CNT) 91 #define TI_TSC2046_INT_VREF 2500 92 93 /* Represents a HW sample */ 94 struct tsc2046_adc_atom { 95 /* 96 * Command transmitted to the controller. This field is empty on the RX 97 * buffer. 98 */ 99 u8 cmd; 100 /* 101 * Data received from the controller. This field is empty for the TX 102 * buffer 103 */ 104 __be16 data; 105 } __packed; 106 107 /* Layout of atomic buffers within big buffer */ 108 struct tsc2046_adc_group_layout { 109 /* Group offset within the SPI RX buffer */ 110 unsigned int offset; 111 /* 112 * Amount of tsc2046_adc_atom structs within the same command gathered 113 * within same group. 114 */ 115 unsigned int count; 116 /* 117 * Settling samples (tsc2046_adc_atom structs) which should be skipped 118 * before good samples will start. 119 */ 120 unsigned int skip; 121 }; 122 123 struct tsc2046_adc_dcfg { 124 const struct iio_chan_spec *channels; 125 unsigned int num_channels; 126 }; 127 128 struct tsc2046_adc_ch_cfg { 129 unsigned int settling_time_us; 130 unsigned int oversampling_ratio; 131 }; 132 133 enum tsc2046_state { 134 TSC2046_STATE_SHUTDOWN, 135 TSC2046_STATE_STANDBY, 136 TSC2046_STATE_POLL, 137 TSC2046_STATE_POLL_IRQ_DISABLE, 138 TSC2046_STATE_ENABLE_IRQ, 139 }; 140 141 struct tsc2046_adc_priv { 142 struct spi_device *spi; 143 const struct tsc2046_adc_dcfg *dcfg; 144 struct regulator *vref_reg; 145 146 struct iio_trigger *trig; 147 struct hrtimer trig_timer; 148 enum tsc2046_state state; 149 int poll_cnt; 150 spinlock_t state_lock; 151 152 struct spi_transfer xfer; 153 struct spi_message msg; 154 155 struct { 156 /* Scan data for each channel */ 157 u16 data[TI_TSC2046_MAX_CHAN]; 158 /* Timestamp */ 159 s64 ts __aligned(8); 160 } scan_buf; 161 162 /* 163 * Lock to protect the layout and the SPI transfer buffer. 164 * tsc2046_adc_group_layout can be changed within update_scan_mode(), 165 * in this case the l[] and tx/rx buffer will be out of sync to each 166 * other. 167 */ 168 struct mutex slock; 169 struct tsc2046_adc_group_layout l[TI_TSC2046_MAX_CHAN]; 170 struct tsc2046_adc_atom *rx; 171 struct tsc2046_adc_atom *tx; 172 173 unsigned int count; 174 unsigned int groups; 175 u32 effective_speed_hz; 176 u32 scan_interval_us; 177 u32 time_per_scan_us; 178 u32 time_per_bit_ns; 179 unsigned int vref_mv; 180 181 struct tsc2046_adc_ch_cfg ch_cfg[TI_TSC2046_MAX_CHAN]; 182 }; 183 184 #define TI_TSC2046_V_CHAN(index, bits, name) \ 185 { \ 186 .type = IIO_VOLTAGE, \ 187 .indexed = 1, \ 188 .channel = index, \ 189 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ 190 .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ 191 .datasheet_name = "#name", \ 192 .scan_index = index, \ 193 .scan_type = { \ 194 .sign = 'u', \ 195 .realbits = bits, \ 196 .storagebits = 16, \ 197 .endianness = IIO_CPU, \ 198 }, \ 199 } 200 201 #define DECLARE_TI_TSC2046_8_CHANNELS(name, bits) \ 202 const struct iio_chan_spec name ## _channels[] = { \ 203 TI_TSC2046_V_CHAN(0, bits, TEMP0), \ 204 TI_TSC2046_V_CHAN(1, bits, Y), \ 205 TI_TSC2046_V_CHAN(2, bits, VBAT), \ 206 TI_TSC2046_V_CHAN(3, bits, Z1), \ 207 TI_TSC2046_V_CHAN(4, bits, Z2), \ 208 TI_TSC2046_V_CHAN(5, bits, X), \ 209 TI_TSC2046_V_CHAN(6, bits, AUX), \ 210 TI_TSC2046_V_CHAN(7, bits, TEMP1), \ 211 IIO_CHAN_SOFT_TIMESTAMP(8), \ 212 } 213 214 static DECLARE_TI_TSC2046_8_CHANNELS(tsc2046_adc, 12); 215 216 static const struct tsc2046_adc_dcfg tsc2046_adc_dcfg_tsc2046e = { 217 .channels = tsc2046_adc_channels, 218 .num_channels = ARRAY_SIZE(tsc2046_adc_channels), 219 }; 220 221 /* 222 * Convert time to a number of samples which can be transferred within this 223 * time. 224 */ 225 static unsigned int tsc2046_adc_time_to_count(struct tsc2046_adc_priv *priv, 226 unsigned long time) 227 { 228 unsigned int bit_count, sample_count; 229 230 bit_count = DIV_ROUND_UP(time * NSEC_PER_USEC, priv->time_per_bit_ns); 231 sample_count = DIV_ROUND_UP(bit_count, TI_TSC2046_SAMPLE_BITS); 232 233 dev_dbg(&priv->spi->dev, "Effective speed %u, time per bit: %u, count bits: %u, count samples: %u\n", 234 priv->effective_speed_hz, priv->time_per_bit_ns, 235 bit_count, sample_count); 236 237 return sample_count; 238 } 239 240 static u8 tsc2046_adc_get_cmd(struct tsc2046_adc_priv *priv, int ch_idx, 241 bool keep_power) 242 { 243 u32 pd; 244 245 /* 246 * if PD bits are 0, controller will automatically disable ADC, VREF and 247 * enable IRQ. 248 */ 249 if (keep_power) 250 pd = TI_TSC2046_PD0_ADC_ON; 251 else 252 pd = 0; 253 254 switch (ch_idx) { 255 case TI_TSC2046_ADDR_TEMP1: 256 case TI_TSC2046_ADDR_AUX: 257 case TI_TSC2046_ADDR_VBAT: 258 case TI_TSC2046_ADDR_TEMP0: 259 pd |= TI_TSC2046_SER; 260 if (!priv->vref_reg) 261 pd |= TI_TSC2046_PD1_VREF_ON; 262 } 263 264 return TI_TSC2046_START | FIELD_PREP(TI_TSC2046_ADDR, ch_idx) | pd; 265 } 266 267 static u16 tsc2046_adc_get_value(struct tsc2046_adc_atom *buf) 268 { 269 return FIELD_GET(TI_TSC2046_DATA_12BIT, get_unaligned_be16(&buf->data)); 270 } 271 272 static int tsc2046_adc_read_one(struct tsc2046_adc_priv *priv, int ch_idx, 273 u32 *effective_speed_hz) 274 { 275 struct tsc2046_adc_ch_cfg *ch = &priv->ch_cfg[ch_idx]; 276 struct tsc2046_adc_atom *rx_buf, *tx_buf; 277 unsigned int val, val_normalized = 0; 278 int ret, i, count_skip = 0, max_count; 279 struct spi_transfer xfer; 280 struct spi_message msg; 281 u8 cmd; 282 283 if (!effective_speed_hz) { 284 count_skip = tsc2046_adc_time_to_count(priv, ch->settling_time_us); 285 max_count = count_skip + ch->oversampling_ratio; 286 } else { 287 max_count = 1; 288 } 289 290 if (sizeof(*tx_buf) * max_count > PAGE_SIZE) 291 return -ENOSPC; 292 293 tx_buf = kcalloc(max_count, sizeof(*tx_buf), GFP_KERNEL); 294 if (!tx_buf) 295 return -ENOMEM; 296 297 rx_buf = kcalloc(max_count, sizeof(*rx_buf), GFP_KERNEL); 298 if (!rx_buf) { 299 ret = -ENOMEM; 300 goto free_tx; 301 } 302 303 /* 304 * Do not enable automatic power down on working samples. Otherwise the 305 * plates will never be completely charged. 306 */ 307 cmd = tsc2046_adc_get_cmd(priv, ch_idx, true); 308 309 for (i = 0; i < max_count - 1; i++) 310 tx_buf[i].cmd = cmd; 311 312 /* automatically power down on last sample */ 313 tx_buf[i].cmd = tsc2046_adc_get_cmd(priv, ch_idx, false); 314 315 memset(&xfer, 0, sizeof(xfer)); 316 xfer.tx_buf = tx_buf; 317 xfer.rx_buf = rx_buf; 318 xfer.len = sizeof(*tx_buf) * max_count; 319 spi_message_init_with_transfers(&msg, &xfer, 1); 320 321 /* 322 * We aren't using spi_write_then_read() because we need to be able 323 * to get hold of the effective_speed_hz from the xfer 324 */ 325 ret = spi_sync(priv->spi, &msg); 326 if (ret) { 327 dev_err_ratelimited(&priv->spi->dev, "SPI transfer failed %pe\n", 328 ERR_PTR(ret)); 329 goto free_bufs; 330 } 331 332 if (effective_speed_hz) 333 *effective_speed_hz = xfer.effective_speed_hz; 334 335 for (i = 0; i < max_count - count_skip; i++) { 336 val = tsc2046_adc_get_value(&rx_buf[count_skip + i]); 337 val_normalized += val; 338 } 339 340 ret = DIV_ROUND_UP(val_normalized, max_count - count_skip); 341 342 free_bufs: 343 kfree(rx_buf); 344 free_tx: 345 kfree(tx_buf); 346 347 return ret; 348 } 349 350 static size_t tsc2046_adc_group_set_layout(struct tsc2046_adc_priv *priv, 351 unsigned int group, 352 unsigned int ch_idx) 353 { 354 struct tsc2046_adc_ch_cfg *ch = &priv->ch_cfg[ch_idx]; 355 struct tsc2046_adc_group_layout *cur; 356 unsigned int max_count, count_skip; 357 unsigned int offset = 0; 358 359 if (group) 360 offset = priv->l[group - 1].offset + priv->l[group - 1].count; 361 362 count_skip = tsc2046_adc_time_to_count(priv, ch->settling_time_us); 363 max_count = count_skip + ch->oversampling_ratio; 364 365 cur = &priv->l[group]; 366 cur->offset = offset; 367 cur->count = max_count; 368 cur->skip = count_skip; 369 370 return sizeof(*priv->tx) * max_count; 371 } 372 373 static void tsc2046_adc_group_set_cmd(struct tsc2046_adc_priv *priv, 374 unsigned int group, int ch_idx) 375 { 376 struct tsc2046_adc_group_layout *l = &priv->l[group]; 377 unsigned int i; 378 u8 cmd; 379 380 /* 381 * Do not enable automatic power down on working samples. Otherwise the 382 * plates will never be completely charged. 383 */ 384 cmd = tsc2046_adc_get_cmd(priv, ch_idx, true); 385 386 for (i = 0; i < l->count - 1; i++) 387 priv->tx[l->offset + i].cmd = cmd; 388 389 /* automatically power down on last sample */ 390 priv->tx[l->offset + i].cmd = tsc2046_adc_get_cmd(priv, ch_idx, false); 391 } 392 393 static u16 tsc2046_adc_get_val(struct tsc2046_adc_priv *priv, int group) 394 { 395 struct tsc2046_adc_group_layout *l; 396 unsigned int val, val_normalized = 0; 397 int valid_count, i; 398 399 l = &priv->l[group]; 400 valid_count = l->count - l->skip; 401 402 for (i = 0; i < valid_count; i++) { 403 val = tsc2046_adc_get_value(&priv->rx[l->offset + l->skip + i]); 404 val_normalized += val; 405 } 406 407 return DIV_ROUND_UP(val_normalized, valid_count); 408 } 409 410 static int tsc2046_adc_scan(struct iio_dev *indio_dev) 411 { 412 struct tsc2046_adc_priv *priv = iio_priv(indio_dev); 413 struct device *dev = &priv->spi->dev; 414 int group; 415 int ret; 416 417 ret = spi_sync(priv->spi, &priv->msg); 418 if (ret < 0) { 419 dev_err_ratelimited(dev, "SPI transfer failed: %pe\n", ERR_PTR(ret)); 420 return ret; 421 } 422 423 for (group = 0; group < priv->groups; group++) 424 priv->scan_buf.data[group] = tsc2046_adc_get_val(priv, group); 425 426 ret = iio_push_to_buffers_with_timestamp(indio_dev, &priv->scan_buf, 427 iio_get_time_ns(indio_dev)); 428 /* If the consumer is kfifo, we may get a EBUSY here - ignore it. */ 429 if (ret < 0 && ret != -EBUSY) { 430 dev_err_ratelimited(dev, "Failed to push scan buffer %pe\n", 431 ERR_PTR(ret)); 432 433 return ret; 434 } 435 436 return 0; 437 } 438 439 static irqreturn_t tsc2046_adc_trigger_handler(int irq, void *p) 440 { 441 struct iio_poll_func *pf = p; 442 struct iio_dev *indio_dev = pf->indio_dev; 443 struct tsc2046_adc_priv *priv = iio_priv(indio_dev); 444 445 mutex_lock(&priv->slock); 446 tsc2046_adc_scan(indio_dev); 447 mutex_unlock(&priv->slock); 448 449 iio_trigger_notify_done(indio_dev->trig); 450 451 return IRQ_HANDLED; 452 } 453 454 static int tsc2046_adc_read_raw(struct iio_dev *indio_dev, 455 struct iio_chan_spec const *chan, 456 int *val, int *val2, long m) 457 { 458 struct tsc2046_adc_priv *priv = iio_priv(indio_dev); 459 int ret; 460 461 switch (m) { 462 case IIO_CHAN_INFO_RAW: 463 ret = tsc2046_adc_read_one(priv, chan->channel, NULL); 464 if (ret < 0) 465 return ret; 466 467 *val = ret; 468 469 return IIO_VAL_INT; 470 case IIO_CHAN_INFO_SCALE: 471 /* 472 * Note: the TSC2046 has internal voltage divider on the VBAT 473 * line. This divider can be influenced by external divider. 474 * So, it is better to use external voltage-divider driver 475 * instead, which is calculating complete chain. 476 */ 477 *val = priv->vref_mv; 478 *val2 = chan->scan_type.realbits; 479 return IIO_VAL_FRACTIONAL_LOG2; 480 } 481 482 return -EINVAL; 483 } 484 485 static int tsc2046_adc_update_scan_mode(struct iio_dev *indio_dev, 486 const unsigned long *active_scan_mask) 487 { 488 struct tsc2046_adc_priv *priv = iio_priv(indio_dev); 489 unsigned int ch_idx, group = 0; 490 size_t size; 491 492 mutex_lock(&priv->slock); 493 494 size = 0; 495 for_each_set_bit(ch_idx, active_scan_mask, ARRAY_SIZE(priv->l)) { 496 size += tsc2046_adc_group_set_layout(priv, group, ch_idx); 497 tsc2046_adc_group_set_cmd(priv, group, ch_idx); 498 group++; 499 } 500 501 priv->groups = group; 502 priv->xfer.len = size; 503 priv->time_per_scan_us = size * 8 * priv->time_per_bit_ns / NSEC_PER_USEC; 504 505 if (priv->scan_interval_us < priv->time_per_scan_us) 506 dev_warn(&priv->spi->dev, "The scan interval (%d) is less then calculated scan time (%d)\n", 507 priv->scan_interval_us, priv->time_per_scan_us); 508 509 mutex_unlock(&priv->slock); 510 511 return 0; 512 } 513 514 static const struct iio_info tsc2046_adc_info = { 515 .read_raw = tsc2046_adc_read_raw, 516 .update_scan_mode = tsc2046_adc_update_scan_mode, 517 }; 518 519 static enum hrtimer_restart tsc2046_adc_timer(struct hrtimer *hrtimer) 520 { 521 struct tsc2046_adc_priv *priv = container_of(hrtimer, 522 struct tsc2046_adc_priv, 523 trig_timer); 524 unsigned long flags; 525 526 /* 527 * This state machine should address following challenges : 528 * - the interrupt source is based on level shifter attached to the X 529 * channel of ADC. It will change the state every time we switch 530 * between channels. So, we need to disable IRQ if we do 531 * iio_trigger_poll(). 532 * - we should do iio_trigger_poll() at some reduced sample rate 533 * - we should still trigger for some amount of time after last 534 * interrupt with enabled IRQ was processed. 535 */ 536 537 spin_lock_irqsave(&priv->state_lock, flags); 538 switch (priv->state) { 539 case TSC2046_STATE_ENABLE_IRQ: 540 if (priv->poll_cnt < TI_TSC2046_POLL_CNT) { 541 priv->poll_cnt++; 542 hrtimer_start(&priv->trig_timer, 543 ns_to_ktime(priv->scan_interval_us * 544 NSEC_PER_USEC), 545 HRTIMER_MODE_REL_SOFT); 546 547 if (priv->poll_cnt >= TI_TSC2046_MIN_POLL_CNT) { 548 priv->state = TSC2046_STATE_POLL_IRQ_DISABLE; 549 enable_irq(priv->spi->irq); 550 } else { 551 priv->state = TSC2046_STATE_POLL; 552 } 553 } else { 554 priv->state = TSC2046_STATE_STANDBY; 555 enable_irq(priv->spi->irq); 556 } 557 break; 558 case TSC2046_STATE_POLL_IRQ_DISABLE: 559 disable_irq_nosync(priv->spi->irq); 560 fallthrough; 561 case TSC2046_STATE_POLL: 562 priv->state = TSC2046_STATE_ENABLE_IRQ; 563 /* iio_trigger_poll() starts hrtimer */ 564 iio_trigger_poll(priv->trig); 565 break; 566 case TSC2046_STATE_SHUTDOWN: 567 break; 568 case TSC2046_STATE_STANDBY: 569 fallthrough; 570 default: 571 dev_warn(&priv->spi->dev, "Got unexpected state: %i\n", 572 priv->state); 573 break; 574 } 575 spin_unlock_irqrestore(&priv->state_lock, flags); 576 577 return HRTIMER_NORESTART; 578 } 579 580 static irqreturn_t tsc2046_adc_irq(int irq, void *dev_id) 581 { 582 struct iio_dev *indio_dev = dev_id; 583 struct tsc2046_adc_priv *priv = iio_priv(indio_dev); 584 unsigned long flags; 585 586 hrtimer_try_to_cancel(&priv->trig_timer); 587 588 spin_lock_irqsave(&priv->state_lock, flags); 589 if (priv->state != TSC2046_STATE_SHUTDOWN) { 590 priv->state = TSC2046_STATE_ENABLE_IRQ; 591 priv->poll_cnt = 0; 592 593 /* iio_trigger_poll() starts hrtimer */ 594 disable_irq_nosync(priv->spi->irq); 595 iio_trigger_poll(priv->trig); 596 } 597 spin_unlock_irqrestore(&priv->state_lock, flags); 598 599 return IRQ_HANDLED; 600 } 601 602 static void tsc2046_adc_reenable_trigger(struct iio_trigger *trig) 603 { 604 struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig); 605 struct tsc2046_adc_priv *priv = iio_priv(indio_dev); 606 ktime_t tim; 607 608 /* 609 * We can sample it as fast as we can, but usually we do not need so 610 * many samples. Reduce the sample rate for default (touchscreen) use 611 * case. 612 */ 613 tim = ns_to_ktime((priv->scan_interval_us - priv->time_per_scan_us) * 614 NSEC_PER_USEC); 615 hrtimer_start(&priv->trig_timer, tim, HRTIMER_MODE_REL_SOFT); 616 } 617 618 static int tsc2046_adc_set_trigger_state(struct iio_trigger *trig, bool enable) 619 { 620 struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig); 621 struct tsc2046_adc_priv *priv = iio_priv(indio_dev); 622 unsigned long flags; 623 624 if (enable) { 625 spin_lock_irqsave(&priv->state_lock, flags); 626 if (priv->state == TSC2046_STATE_SHUTDOWN) { 627 priv->state = TSC2046_STATE_STANDBY; 628 enable_irq(priv->spi->irq); 629 } 630 spin_unlock_irqrestore(&priv->state_lock, flags); 631 } else { 632 spin_lock_irqsave(&priv->state_lock, flags); 633 634 if (priv->state == TSC2046_STATE_STANDBY || 635 priv->state == TSC2046_STATE_POLL_IRQ_DISABLE) 636 disable_irq_nosync(priv->spi->irq); 637 638 priv->state = TSC2046_STATE_SHUTDOWN; 639 spin_unlock_irqrestore(&priv->state_lock, flags); 640 641 hrtimer_cancel(&priv->trig_timer); 642 } 643 644 return 0; 645 } 646 647 static const struct iio_trigger_ops tsc2046_adc_trigger_ops = { 648 .set_trigger_state = tsc2046_adc_set_trigger_state, 649 .reenable = tsc2046_adc_reenable_trigger, 650 }; 651 652 static int tsc2046_adc_setup_spi_msg(struct tsc2046_adc_priv *priv) 653 { 654 unsigned int ch_idx; 655 size_t size; 656 int ret; 657 658 /* 659 * Make dummy read to set initial power state and get real SPI clock 660 * freq. It seems to be not important which channel is used for this 661 * case. 662 */ 663 ret = tsc2046_adc_read_one(priv, TI_TSC2046_ADDR_TEMP0, 664 &priv->effective_speed_hz); 665 if (ret < 0) 666 return ret; 667 668 /* 669 * In case SPI controller do not report effective_speed_hz, use 670 * configure value and hope it will match. 671 */ 672 if (!priv->effective_speed_hz) 673 priv->effective_speed_hz = priv->spi->max_speed_hz; 674 675 676 priv->scan_interval_us = TI_TSC2046_SAMPLE_INTERVAL_US; 677 priv->time_per_bit_ns = DIV_ROUND_UP(NSEC_PER_SEC, 678 priv->effective_speed_hz); 679 680 /* 681 * Calculate and allocate maximal size buffer if all channels are 682 * enabled. 683 */ 684 size = 0; 685 for (ch_idx = 0; ch_idx < ARRAY_SIZE(priv->l); ch_idx++) 686 size += tsc2046_adc_group_set_layout(priv, ch_idx, ch_idx); 687 688 if (size > PAGE_SIZE) { 689 dev_err(&priv->spi->dev, 690 "Calculated scan buffer is too big. Try to reduce spi-max-frequency, settling-time-us or oversampling-ratio\n"); 691 return -ENOSPC; 692 } 693 694 priv->tx = devm_kzalloc(&priv->spi->dev, size, GFP_KERNEL); 695 if (!priv->tx) 696 return -ENOMEM; 697 698 priv->rx = devm_kzalloc(&priv->spi->dev, size, GFP_KERNEL); 699 if (!priv->rx) 700 return -ENOMEM; 701 702 priv->xfer.tx_buf = priv->tx; 703 priv->xfer.rx_buf = priv->rx; 704 priv->xfer.len = size; 705 spi_message_init_with_transfers(&priv->msg, &priv->xfer, 1); 706 707 return 0; 708 } 709 710 static void tsc2046_adc_parse_fwnode(struct tsc2046_adc_priv *priv) 711 { 712 struct fwnode_handle *child; 713 struct device *dev = &priv->spi->dev; 714 unsigned int i; 715 716 for (i = 0; i < ARRAY_SIZE(priv->ch_cfg); i++) { 717 priv->ch_cfg[i].settling_time_us = 1; 718 priv->ch_cfg[i].oversampling_ratio = 1; 719 } 720 721 device_for_each_child_node(dev, child) { 722 u32 stl, overs, reg; 723 int ret; 724 725 ret = fwnode_property_read_u32(child, "reg", ®); 726 if (ret) { 727 dev_err(dev, "invalid reg on %pfw, err: %pe\n", child, 728 ERR_PTR(ret)); 729 continue; 730 } 731 732 if (reg >= ARRAY_SIZE(priv->ch_cfg)) { 733 dev_err(dev, "%pfw: Unsupported reg value: %i, max supported is: %zu.\n", 734 child, reg, ARRAY_SIZE(priv->ch_cfg)); 735 continue; 736 } 737 738 ret = fwnode_property_read_u32(child, "settling-time-us", &stl); 739 if (!ret) 740 priv->ch_cfg[reg].settling_time_us = stl; 741 742 ret = fwnode_property_read_u32(child, "oversampling-ratio", 743 &overs); 744 if (!ret) 745 priv->ch_cfg[reg].oversampling_ratio = overs; 746 } 747 } 748 749 static void tsc2046_adc_regulator_disable(void *data) 750 { 751 struct tsc2046_adc_priv *priv = data; 752 753 regulator_disable(priv->vref_reg); 754 } 755 756 static int tsc2046_adc_configure_regulator(struct tsc2046_adc_priv *priv) 757 { 758 struct device *dev = &priv->spi->dev; 759 int ret; 760 761 priv->vref_reg = devm_regulator_get_optional(dev, "vref"); 762 if (IS_ERR(priv->vref_reg)) { 763 /* If regulator exists but can't be get, return an error */ 764 if (PTR_ERR(priv->vref_reg) != -ENODEV) 765 return PTR_ERR(priv->vref_reg); 766 priv->vref_reg = NULL; 767 } 768 if (!priv->vref_reg) { 769 /* Use internal reference */ 770 priv->vref_mv = TI_TSC2046_INT_VREF; 771 return 0; 772 } 773 774 ret = regulator_enable(priv->vref_reg); 775 if (ret) 776 return ret; 777 778 ret = devm_add_action_or_reset(dev, tsc2046_adc_regulator_disable, 779 priv); 780 if (ret) 781 return ret; 782 783 ret = regulator_get_voltage(priv->vref_reg); 784 if (ret < 0) 785 return ret; 786 787 priv->vref_mv = ret / MILLI; 788 789 return 0; 790 } 791 792 static int tsc2046_adc_probe(struct spi_device *spi) 793 { 794 const struct tsc2046_adc_dcfg *dcfg; 795 struct device *dev = &spi->dev; 796 struct tsc2046_adc_priv *priv; 797 struct iio_dev *indio_dev; 798 struct iio_trigger *trig; 799 int ret; 800 801 if (spi->max_speed_hz > TI_TSC2046_MAX_CLK_FREQ) { 802 dev_err(dev, "SPI max_speed_hz is too high: %d Hz. Max supported freq is %zu Hz\n", 803 spi->max_speed_hz, TI_TSC2046_MAX_CLK_FREQ); 804 return -EINVAL; 805 } 806 807 dcfg = spi_get_device_match_data(spi); 808 if (!dcfg) 809 return -EINVAL; 810 811 spi->bits_per_word = 8; 812 spi->mode &= ~SPI_MODE_X_MASK; 813 spi->mode |= SPI_MODE_0; 814 ret = spi_setup(spi); 815 if (ret < 0) 816 return dev_err_probe(dev, ret, "Error in SPI setup\n"); 817 818 indio_dev = devm_iio_device_alloc(dev, sizeof(*priv)); 819 if (!indio_dev) 820 return -ENOMEM; 821 822 priv = iio_priv(indio_dev); 823 priv->dcfg = dcfg; 824 825 priv->spi = spi; 826 827 indio_dev->name = TI_TSC2046_NAME; 828 indio_dev->modes = INDIO_DIRECT_MODE; 829 indio_dev->channels = dcfg->channels; 830 indio_dev->num_channels = dcfg->num_channels; 831 indio_dev->info = &tsc2046_adc_info; 832 833 ret = tsc2046_adc_configure_regulator(priv); 834 if (ret) 835 return ret; 836 837 tsc2046_adc_parse_fwnode(priv); 838 839 ret = tsc2046_adc_setup_spi_msg(priv); 840 if (ret) 841 return ret; 842 843 mutex_init(&priv->slock); 844 845 ret = devm_request_irq(dev, spi->irq, &tsc2046_adc_irq, 846 IRQF_NO_AUTOEN, indio_dev->name, indio_dev); 847 if (ret) 848 return ret; 849 850 trig = devm_iio_trigger_alloc(dev, "touchscreen-%s", indio_dev->name); 851 if (!trig) 852 return -ENOMEM; 853 854 priv->trig = trig; 855 iio_trigger_set_drvdata(trig, indio_dev); 856 trig->ops = &tsc2046_adc_trigger_ops; 857 858 spin_lock_init(&priv->state_lock); 859 priv->state = TSC2046_STATE_SHUTDOWN; 860 hrtimer_init(&priv->trig_timer, CLOCK_MONOTONIC, 861 HRTIMER_MODE_REL_SOFT); 862 priv->trig_timer.function = tsc2046_adc_timer; 863 864 ret = devm_iio_trigger_register(dev, trig); 865 if (ret) { 866 dev_err(dev, "failed to register trigger\n"); 867 return ret; 868 } 869 870 ret = devm_iio_triggered_buffer_setup(dev, indio_dev, NULL, 871 &tsc2046_adc_trigger_handler, NULL); 872 if (ret) { 873 dev_err(dev, "Failed to setup triggered buffer\n"); 874 return ret; 875 } 876 877 /* set default trigger */ 878 indio_dev->trig = iio_trigger_get(priv->trig); 879 880 return devm_iio_device_register(dev, indio_dev); 881 } 882 883 static const struct of_device_id ads7950_of_table[] = { 884 { .compatible = "ti,tsc2046e-adc", .data = &tsc2046_adc_dcfg_tsc2046e }, 885 { } 886 }; 887 MODULE_DEVICE_TABLE(of, ads7950_of_table); 888 889 static const struct spi_device_id tsc2046_adc_spi_ids[] = { 890 { "tsc2046e-adc", (unsigned long)&tsc2046_adc_dcfg_tsc2046e }, 891 { } 892 }; 893 MODULE_DEVICE_TABLE(spi, tsc2046_adc_spi_ids); 894 895 static struct spi_driver tsc2046_adc_driver = { 896 .driver = { 897 .name = "tsc2046", 898 .of_match_table = ads7950_of_table, 899 }, 900 .id_table = tsc2046_adc_spi_ids, 901 .probe = tsc2046_adc_probe, 902 }; 903 module_spi_driver(tsc2046_adc_driver); 904 905 MODULE_AUTHOR("Oleksij Rempel <kernel@pengutronix.de>"); 906 MODULE_DESCRIPTION("TI TSC2046 ADC"); 907 MODULE_LICENSE("GPL v2"); 908