1 /* 2 * P2WI (Push-Pull Two Wire Interface) bus driver. 3 * 4 * Author: Boris BREZILLON <boris.brezillon@free-electrons.com> 5 * 6 * This file is licensed under the terms of the GNU General Public License 7 * version 2. This program is licensed "as is" without any warranty of any 8 * kind, whether express or implied. 9 * 10 * The P2WI controller looks like an SMBus controller which only supports byte 11 * data transfers. But, it differs from standard SMBus protocol on several 12 * aspects: 13 * - it supports only one slave device, and thus drop the address field 14 * - it adds a parity bit every 8bits of data 15 * - only one read access is required to read a byte (instead of a write 16 * followed by a read access in standard SMBus protocol) 17 * - there's no Ack bit after each byte transfer 18 * 19 * This means this bus cannot be used to interface with standard SMBus 20 * devices (the only known device to support this interface is the AXP221 21 * PMIC). 22 * 23 */ 24 #include <linux/clk.h> 25 #include <linux/i2c.h> 26 #include <linux/io.h> 27 #include <linux/interrupt.h> 28 #include <linux/module.h> 29 #include <linux/of.h> 30 #include <linux/platform_device.h> 31 #include <linux/reset.h> 32 33 34 /* P2WI registers */ 35 #define P2WI_CTRL 0x0 36 #define P2WI_CCR 0x4 37 #define P2WI_INTE 0x8 38 #define P2WI_INTS 0xc 39 #define P2WI_DADDR0 0x10 40 #define P2WI_DADDR1 0x14 41 #define P2WI_DLEN 0x18 42 #define P2WI_DATA0 0x1c 43 #define P2WI_DATA1 0x20 44 #define P2WI_LCR 0x24 45 #define P2WI_PMCR 0x28 46 47 /* CTRL fields */ 48 #define P2WI_CTRL_START_TRANS BIT(7) 49 #define P2WI_CTRL_ABORT_TRANS BIT(6) 50 #define P2WI_CTRL_GLOBAL_INT_ENB BIT(1) 51 #define P2WI_CTRL_SOFT_RST BIT(0) 52 53 /* CLK CTRL fields */ 54 #define P2WI_CCR_SDA_OUT_DELAY(v) (((v) & 0x7) << 8) 55 #define P2WI_CCR_MAX_CLK_DIV 0xff 56 #define P2WI_CCR_CLK_DIV(v) ((v) & P2WI_CCR_MAX_CLK_DIV) 57 58 /* STATUS fields */ 59 #define P2WI_INTS_TRANS_ERR_ID(v) (((v) >> 8) & 0xff) 60 #define P2WI_INTS_LOAD_BSY BIT(2) 61 #define P2WI_INTS_TRANS_ERR BIT(1) 62 #define P2WI_INTS_TRANS_OVER BIT(0) 63 64 /* DATA LENGTH fields*/ 65 #define P2WI_DLEN_READ BIT(4) 66 #define P2WI_DLEN_DATA_LENGTH(v) ((v - 1) & 0x7) 67 68 /* LINE CTRL fields*/ 69 #define P2WI_LCR_SCL_STATE BIT(5) 70 #define P2WI_LCR_SDA_STATE BIT(4) 71 #define P2WI_LCR_SCL_CTL BIT(3) 72 #define P2WI_LCR_SCL_CTL_EN BIT(2) 73 #define P2WI_LCR_SDA_CTL BIT(1) 74 #define P2WI_LCR_SDA_CTL_EN BIT(0) 75 76 /* PMU MODE CTRL fields */ 77 #define P2WI_PMCR_PMU_INIT_SEND BIT(31) 78 #define P2WI_PMCR_PMU_INIT_DATA(v) (((v) & 0xff) << 16) 79 #define P2WI_PMCR_PMU_MODE_REG(v) (((v) & 0xff) << 8) 80 #define P2WI_PMCR_PMU_DEV_ADDR(v) ((v) & 0xff) 81 82 #define P2WI_MAX_FREQ 6000000 83 84 struct p2wi { 85 struct i2c_adapter adapter; 86 struct completion complete; 87 unsigned int status; 88 void __iomem *regs; 89 struct clk *clk; 90 struct reset_control *rstc; 91 int slave_addr; 92 }; 93 94 static irqreturn_t p2wi_interrupt(int irq, void *dev_id) 95 { 96 struct p2wi *p2wi = dev_id; 97 unsigned long status; 98 99 status = readl(p2wi->regs + P2WI_INTS); 100 p2wi->status = status; 101 102 /* Clear interrupts */ 103 status &= (P2WI_INTS_LOAD_BSY | P2WI_INTS_TRANS_ERR | 104 P2WI_INTS_TRANS_OVER); 105 writel(status, p2wi->regs + P2WI_INTS); 106 107 complete(&p2wi->complete); 108 109 return IRQ_HANDLED; 110 } 111 112 static u32 p2wi_functionality(struct i2c_adapter *adap) 113 { 114 return I2C_FUNC_SMBUS_BYTE_DATA; 115 } 116 117 static int p2wi_smbus_xfer(struct i2c_adapter *adap, u16 addr, 118 unsigned short flags, char read_write, 119 u8 command, int size, union i2c_smbus_data *data) 120 { 121 struct p2wi *p2wi = i2c_get_adapdata(adap); 122 unsigned long dlen = P2WI_DLEN_DATA_LENGTH(1); 123 124 if (p2wi->slave_addr >= 0 && addr != p2wi->slave_addr) { 125 dev_err(&adap->dev, "invalid P2WI address\n"); 126 return -EINVAL; 127 } 128 129 if (!data) 130 return -EINVAL; 131 132 writel(command, p2wi->regs + P2WI_DADDR0); 133 134 if (read_write == I2C_SMBUS_READ) 135 dlen |= P2WI_DLEN_READ; 136 else 137 writel(data->byte, p2wi->regs + P2WI_DATA0); 138 139 writel(dlen, p2wi->regs + P2WI_DLEN); 140 141 if (readl(p2wi->regs + P2WI_CTRL) & P2WI_CTRL_START_TRANS) { 142 dev_err(&adap->dev, "P2WI bus busy\n"); 143 return -EBUSY; 144 } 145 146 reinit_completion(&p2wi->complete); 147 148 writel(P2WI_INTS_LOAD_BSY | P2WI_INTS_TRANS_ERR | P2WI_INTS_TRANS_OVER, 149 p2wi->regs + P2WI_INTE); 150 151 writel(P2WI_CTRL_START_TRANS | P2WI_CTRL_GLOBAL_INT_ENB, 152 p2wi->regs + P2WI_CTRL); 153 154 wait_for_completion(&p2wi->complete); 155 156 if (p2wi->status & P2WI_INTS_LOAD_BSY) { 157 dev_err(&adap->dev, "P2WI bus busy\n"); 158 return -EBUSY; 159 } 160 161 if (p2wi->status & P2WI_INTS_TRANS_ERR) { 162 dev_err(&adap->dev, "P2WI bus xfer error\n"); 163 return -ENXIO; 164 } 165 166 if (read_write == I2C_SMBUS_READ) 167 data->byte = readl(p2wi->regs + P2WI_DATA0); 168 169 return 0; 170 } 171 172 static const struct i2c_algorithm p2wi_algo = { 173 .smbus_xfer = p2wi_smbus_xfer, 174 .functionality = p2wi_functionality, 175 }; 176 177 static const struct of_device_id p2wi_of_match_table[] = { 178 { .compatible = "allwinner,sun6i-a31-p2wi" }, 179 {} 180 }; 181 MODULE_DEVICE_TABLE(of, p2wi_of_match_table); 182 183 static int p2wi_probe(struct platform_device *pdev) 184 { 185 struct device *dev = &pdev->dev; 186 struct device_node *np = dev->of_node; 187 struct device_node *childnp; 188 unsigned long parent_clk_freq; 189 u32 clk_freq = I2C_MAX_STANDARD_MODE_FREQ; 190 struct p2wi *p2wi; 191 u32 slave_addr; 192 int clk_div; 193 int irq; 194 int ret; 195 196 of_property_read_u32(np, "clock-frequency", &clk_freq); 197 if (clk_freq > P2WI_MAX_FREQ) { 198 dev_err(dev, 199 "required clock-frequency (%u Hz) is too high (max = 6MHz)", 200 clk_freq); 201 return -EINVAL; 202 } 203 204 if (clk_freq == 0) { 205 dev_err(dev, "clock-frequency is set to 0 in DT\n"); 206 return -EINVAL; 207 } 208 209 if (of_get_child_count(np) > 1) { 210 dev_err(dev, "P2WI only supports one slave device\n"); 211 return -EINVAL; 212 } 213 214 p2wi = devm_kzalloc(dev, sizeof(struct p2wi), GFP_KERNEL); 215 if (!p2wi) 216 return -ENOMEM; 217 218 p2wi->slave_addr = -1; 219 220 /* 221 * Authorize a p2wi node without any children to be able to use an 222 * i2c-dev from userpace. 223 * In this case the slave_addr is set to -1 and won't be checked when 224 * launching a P2WI transfer. 225 */ 226 childnp = of_get_next_available_child(np, NULL); 227 if (childnp) { 228 ret = of_property_read_u32(childnp, "reg", &slave_addr); 229 if (ret) { 230 dev_err(dev, "invalid slave address on node %pOF\n", 231 childnp); 232 return -EINVAL; 233 } 234 235 p2wi->slave_addr = slave_addr; 236 } 237 238 p2wi->regs = devm_platform_ioremap_resource(pdev, 0); 239 if (IS_ERR(p2wi->regs)) 240 return PTR_ERR(p2wi->regs); 241 242 strscpy(p2wi->adapter.name, pdev->name, sizeof(p2wi->adapter.name)); 243 irq = platform_get_irq(pdev, 0); 244 if (irq < 0) 245 return irq; 246 247 p2wi->clk = devm_clk_get_enabled(dev, NULL); 248 if (IS_ERR(p2wi->clk)) { 249 ret = PTR_ERR(p2wi->clk); 250 dev_err(dev, "failed to enable clk: %d\n", ret); 251 return ret; 252 } 253 254 parent_clk_freq = clk_get_rate(p2wi->clk); 255 256 p2wi->rstc = devm_reset_control_get_exclusive(dev, NULL); 257 if (IS_ERR(p2wi->rstc)) { 258 dev_err(dev, "failed to retrieve reset controller: %pe\n", 259 p2wi->rstc); 260 return PTR_ERR(p2wi->rstc); 261 } 262 263 ret = reset_control_deassert(p2wi->rstc); 264 if (ret) { 265 dev_err(dev, "failed to deassert reset line: %d\n", ret); 266 return ret; 267 } 268 269 init_completion(&p2wi->complete); 270 p2wi->adapter.dev.parent = dev; 271 p2wi->adapter.algo = &p2wi_algo; 272 p2wi->adapter.owner = THIS_MODULE; 273 p2wi->adapter.dev.of_node = pdev->dev.of_node; 274 platform_set_drvdata(pdev, p2wi); 275 i2c_set_adapdata(&p2wi->adapter, p2wi); 276 277 ret = devm_request_irq(dev, irq, p2wi_interrupt, 0, pdev->name, p2wi); 278 if (ret) { 279 dev_err(dev, "can't register interrupt handler irq%d: %d\n", 280 irq, ret); 281 goto err_reset_assert; 282 } 283 284 writel(P2WI_CTRL_SOFT_RST, p2wi->regs + P2WI_CTRL); 285 286 clk_div = parent_clk_freq / clk_freq; 287 if (!clk_div) { 288 dev_warn(dev, 289 "clock-frequency is too high, setting it to %lu Hz\n", 290 parent_clk_freq); 291 clk_div = 1; 292 } else if (clk_div > P2WI_CCR_MAX_CLK_DIV) { 293 dev_warn(dev, 294 "clock-frequency is too low, setting it to %lu Hz\n", 295 parent_clk_freq / P2WI_CCR_MAX_CLK_DIV); 296 clk_div = P2WI_CCR_MAX_CLK_DIV; 297 } 298 299 writel(P2WI_CCR_SDA_OUT_DELAY(1) | P2WI_CCR_CLK_DIV(clk_div), 300 p2wi->regs + P2WI_CCR); 301 302 ret = i2c_add_adapter(&p2wi->adapter); 303 if (!ret) 304 return 0; 305 306 err_reset_assert: 307 reset_control_assert(p2wi->rstc); 308 309 return ret; 310 } 311 312 static void p2wi_remove(struct platform_device *dev) 313 { 314 struct p2wi *p2wi = platform_get_drvdata(dev); 315 316 reset_control_assert(p2wi->rstc); 317 i2c_del_adapter(&p2wi->adapter); 318 } 319 320 static struct platform_driver p2wi_driver = { 321 .probe = p2wi_probe, 322 .remove_new = p2wi_remove, 323 .driver = { 324 .name = "i2c-sunxi-p2wi", 325 .of_match_table = p2wi_of_match_table, 326 }, 327 }; 328 module_platform_driver(p2wi_driver); 329 330 MODULE_AUTHOR("Boris BREZILLON <boris.brezillon@free-electrons.com>"); 331 MODULE_DESCRIPTION("Allwinner P2WI driver"); 332 MODULE_LICENSE("GPL v2"); 333