1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Driver for the Renesas R-Car I2C unit 4 * 5 * Copyright (C) 2014-19 Wolfram Sang <wsa@sang-engineering.com> 6 * Copyright (C) 2011-2019 Renesas Electronics Corporation 7 * 8 * Copyright (C) 2012-14 Renesas Solutions Corp. 9 * Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> 10 * 11 * This file is based on the drivers/i2c/busses/i2c-sh7760.c 12 * (c) 2005-2008 MSC Vertriebsges.m.b.H, Manuel Lauss <mlau@msc-ge.com> 13 */ 14 #include <linux/bitops.h> 15 #include <linux/clk.h> 16 #include <linux/delay.h> 17 #include <linux/dmaengine.h> 18 #include <linux/dma-mapping.h> 19 #include <linux/err.h> 20 #include <linux/interrupt.h> 21 #include <linux/io.h> 22 #include <linux/iopoll.h> 23 #include <linux/i2c.h> 24 #include <linux/i2c-smbus.h> 25 #include <linux/kernel.h> 26 #include <linux/module.h> 27 #include <linux/of.h> 28 #include <linux/platform_device.h> 29 #include <linux/pm_runtime.h> 30 #include <linux/reset.h> 31 #include <linux/slab.h> 32 33 /* register offsets */ 34 #define ICSCR 0x00 /* slave ctrl */ 35 #define ICMCR 0x04 /* master ctrl */ 36 #define ICSSR 0x08 /* slave status */ 37 #define ICMSR 0x0C /* master status */ 38 #define ICSIER 0x10 /* slave irq enable */ 39 #define ICMIER 0x14 /* master irq enable */ 40 #define ICCCR 0x18 /* clock dividers */ 41 #define ICSAR 0x1C /* slave address */ 42 #define ICMAR 0x20 /* master address */ 43 #define ICRXTX 0x24 /* data port */ 44 #define ICCCR2 0x28 /* Clock control 2 */ 45 #define ICMPR 0x2C /* SCL mask control */ 46 #define ICHPR 0x30 /* SCL HIGH control */ 47 #define ICLPR 0x34 /* SCL LOW control */ 48 #define ICFBSCR 0x38 /* first bit setup cycle (Gen3) */ 49 #define ICDMAER 0x3c /* DMA enable (Gen3) */ 50 51 /* ICSCR */ 52 #define SDBS BIT(3) /* slave data buffer select */ 53 #define SIE BIT(2) /* slave interface enable */ 54 #define GCAE BIT(1) /* general call address enable */ 55 #define FNA BIT(0) /* forced non acknowledgment */ 56 57 /* ICMCR */ 58 #define MDBS BIT(7) /* non-fifo mode switch */ 59 #define FSCL BIT(6) /* override SCL pin */ 60 #define FSDA BIT(5) /* override SDA pin */ 61 #define OBPC BIT(4) /* override pins */ 62 #define MIE BIT(3) /* master if enable */ 63 #define TSBE BIT(2) 64 #define FSB BIT(1) /* force stop bit */ 65 #define ESG BIT(0) /* enable start bit gen */ 66 67 /* ICSSR (also for ICSIER) */ 68 #define GCAR BIT(6) /* general call received */ 69 #define STM BIT(5) /* slave transmit mode */ 70 #define SSR BIT(4) /* stop received */ 71 #define SDE BIT(3) /* slave data empty */ 72 #define SDT BIT(2) /* slave data transmitted */ 73 #define SDR BIT(1) /* slave data received */ 74 #define SAR BIT(0) /* slave addr received */ 75 76 /* ICMSR (also for ICMIE) */ 77 #define MNR BIT(6) /* nack received */ 78 #define MAL BIT(5) /* arbitration lost */ 79 #define MST BIT(4) /* sent a stop */ 80 #define MDE BIT(3) 81 #define MDT BIT(2) 82 #define MDR BIT(1) 83 #define MAT BIT(0) /* slave addr xfer done */ 84 85 /* ICDMAER */ 86 #define RSDMAE BIT(3) /* DMA Slave Received Enable */ 87 #define TSDMAE BIT(2) /* DMA Slave Transmitted Enable */ 88 #define RMDMAE BIT(1) /* DMA Master Received Enable */ 89 #define TMDMAE BIT(0) /* DMA Master Transmitted Enable */ 90 91 /* ICCCR2 */ 92 #define FMPE BIT(7) /* Fast Mode Plus Enable */ 93 #define CDFD BIT(2) /* CDF Disable */ 94 #define HLSE BIT(1) /* HIGH/LOW Separate Control Enable */ 95 #define SME BIT(0) /* SCL Mask Enable */ 96 97 /* ICFBSCR */ 98 #define TCYC17 0x0f /* 17*Tcyc delay 1st bit between SDA and SCL */ 99 100 #define RCAR_MIN_DMA_LEN 8 101 102 /* SCL low/high ratio 5:4 to meet all I2C timing specs (incl safety margin) */ 103 #define RCAR_SCLD_RATIO 5 104 #define RCAR_SCHD_RATIO 4 105 /* 106 * SMD should be smaller than SCLD/SCHD and is always around 20 in the docs. 107 * Thus, we simply use 20 which works for low and high speeds. 108 */ 109 #define RCAR_DEFAULT_SMD 20 110 111 #define RCAR_BUS_PHASE_START (MDBS | MIE | ESG) 112 #define RCAR_BUS_PHASE_DATA (MDBS | MIE) 113 #define RCAR_BUS_PHASE_STOP (MDBS | MIE | FSB) 114 115 #define RCAR_IRQ_SEND (MNR | MAL | MST | MAT | MDE) 116 #define RCAR_IRQ_RECV (MNR | MAL | MST | MAT | MDR) 117 #define RCAR_IRQ_STOP (MST) 118 119 #define ID_LAST_MSG BIT(0) 120 #define ID_REP_AFTER_RD BIT(1) 121 #define ID_DONE BIT(2) 122 #define ID_ARBLOST BIT(3) 123 #define ID_NACK BIT(4) 124 #define ID_EPROTO BIT(5) 125 /* persistent flags */ 126 #define ID_P_FMPLUS BIT(27) 127 #define ID_P_NOT_ATOMIC BIT(28) 128 #define ID_P_HOST_NOTIFY BIT(29) 129 #define ID_P_NO_RXDMA BIT(30) /* HW forbids RXDMA sometimes */ 130 #define ID_P_PM_BLOCKED BIT(31) 131 #define ID_P_MASK GENMASK(31, 27) 132 133 enum rcar_i2c_type { 134 I2C_RCAR_GEN1, 135 I2C_RCAR_GEN2, 136 I2C_RCAR_GEN3, 137 I2C_RCAR_GEN4, 138 }; 139 140 struct rcar_i2c_priv { 141 u32 flags; 142 void __iomem *io; 143 struct i2c_adapter adap; 144 struct i2c_msg *msg; 145 int msgs_left; 146 struct clk *clk; 147 148 wait_queue_head_t wait; 149 150 int pos; 151 u32 icccr; 152 u16 schd; 153 u16 scld; 154 u8 smd; 155 u8 recovery_icmcr; /* protected by adapter lock */ 156 enum rcar_i2c_type devtype; 157 struct i2c_client *slave; 158 159 struct resource *res; 160 struct dma_chan *dma_tx; 161 struct dma_chan *dma_rx; 162 struct scatterlist sg; 163 enum dma_data_direction dma_direction; 164 165 struct reset_control *rstc; 166 int irq; 167 168 struct i2c_client *host_notify_client; 169 }; 170 171 #define rcar_i2c_priv_to_dev(p) ((p)->adap.dev.parent) 172 #define rcar_i2c_is_recv(p) ((p)->msg->flags & I2C_M_RD) 173 174 static void rcar_i2c_write(struct rcar_i2c_priv *priv, int reg, u32 val) 175 { 176 writel(val, priv->io + reg); 177 } 178 179 static u32 rcar_i2c_read(struct rcar_i2c_priv *priv, int reg) 180 { 181 return readl(priv->io + reg); 182 } 183 184 static void rcar_i2c_clear_irq(struct rcar_i2c_priv *priv, u32 val) 185 { 186 writel(~val & 0x7f, priv->io + ICMSR); 187 } 188 189 static int rcar_i2c_get_scl(struct i2c_adapter *adap) 190 { 191 struct rcar_i2c_priv *priv = i2c_get_adapdata(adap); 192 193 return !!(rcar_i2c_read(priv, ICMCR) & FSCL); 194 } 195 196 static void rcar_i2c_set_scl(struct i2c_adapter *adap, int val) 197 { 198 struct rcar_i2c_priv *priv = i2c_get_adapdata(adap); 199 200 if (val) 201 priv->recovery_icmcr |= FSCL; 202 else 203 priv->recovery_icmcr &= ~FSCL; 204 205 rcar_i2c_write(priv, ICMCR, priv->recovery_icmcr); 206 } 207 208 static void rcar_i2c_set_sda(struct i2c_adapter *adap, int val) 209 { 210 struct rcar_i2c_priv *priv = i2c_get_adapdata(adap); 211 212 if (val) 213 priv->recovery_icmcr |= FSDA; 214 else 215 priv->recovery_icmcr &= ~FSDA; 216 217 rcar_i2c_write(priv, ICMCR, priv->recovery_icmcr); 218 } 219 220 static int rcar_i2c_get_bus_free(struct i2c_adapter *adap) 221 { 222 struct rcar_i2c_priv *priv = i2c_get_adapdata(adap); 223 224 return !(rcar_i2c_read(priv, ICMCR) & FSDA); 225 } 226 227 static struct i2c_bus_recovery_info rcar_i2c_bri = { 228 .get_scl = rcar_i2c_get_scl, 229 .set_scl = rcar_i2c_set_scl, 230 .set_sda = rcar_i2c_set_sda, 231 .get_bus_free = rcar_i2c_get_bus_free, 232 .recover_bus = i2c_generic_scl_recovery, 233 }; 234 235 static void rcar_i2c_init(struct rcar_i2c_priv *priv) 236 { 237 /* reset master mode */ 238 rcar_i2c_write(priv, ICMIER, 0); 239 rcar_i2c_write(priv, ICMCR, MDBS); 240 rcar_i2c_write(priv, ICMSR, 0); 241 /* start clock */ 242 if (priv->devtype < I2C_RCAR_GEN3) { 243 rcar_i2c_write(priv, ICCCR, priv->icccr); 244 } else { 245 u32 icccr2 = CDFD | HLSE | SME; 246 247 if (priv->flags & ID_P_FMPLUS) 248 icccr2 |= FMPE; 249 250 rcar_i2c_write(priv, ICCCR2, icccr2); 251 rcar_i2c_write(priv, ICCCR, priv->icccr); 252 rcar_i2c_write(priv, ICMPR, priv->smd); 253 rcar_i2c_write(priv, ICHPR, priv->schd); 254 rcar_i2c_write(priv, ICLPR, priv->scld); 255 rcar_i2c_write(priv, ICFBSCR, TCYC17); 256 } 257 } 258 259 static void rcar_i2c_reset_slave(struct rcar_i2c_priv *priv) 260 { 261 rcar_i2c_write(priv, ICSIER, 0); 262 rcar_i2c_write(priv, ICSSR, 0); 263 rcar_i2c_write(priv, ICSCR, SDBS); 264 rcar_i2c_write(priv, ICSAR, 0); /* Gen2: must be 0 if not using slave */ 265 } 266 267 static int rcar_i2c_bus_barrier(struct rcar_i2c_priv *priv) 268 { 269 int ret; 270 u32 val; 271 272 ret = readl_poll_timeout(priv->io + ICMCR, val, !(val & FSDA), 10, 273 priv->adap.timeout); 274 if (ret) { 275 /* Waiting did not help, try to recover */ 276 priv->recovery_icmcr = MDBS | OBPC | FSDA | FSCL; 277 ret = i2c_recover_bus(&priv->adap); 278 } 279 280 return ret; 281 } 282 283 static int rcar_i2c_clock_calculate(struct rcar_i2c_priv *priv) 284 { 285 u32 cdf, round, ick, sum, scl, cdf_width; 286 unsigned long rate; 287 struct device *dev = rcar_i2c_priv_to_dev(priv); 288 struct i2c_timings t = { 289 .bus_freq_hz = I2C_MAX_STANDARD_MODE_FREQ, 290 .scl_fall_ns = 35, 291 .scl_rise_ns = 200, 292 .scl_int_delay_ns = 50, 293 }; 294 295 /* Fall back to previously used values if not supplied */ 296 i2c_parse_fw_timings(dev, &t, false); 297 priv->smd = RCAR_DEFAULT_SMD; 298 299 /* 300 * calculate SCL clock 301 * see 302 * ICCCR (and ICCCR2 for Gen3+) 303 * 304 * ick = clkp / (1 + CDF) 305 * SCL = ick / (20 + SCGD * 8 + F[(ticf + tr + intd) * ick]) 306 * 307 * for Gen3+: 308 * SCL = clkp / (8 + SMD * 2 + SCLD + SCHD +F[(ticf + tr + intd) * clkp]) 309 * 310 * ick : I2C internal clock < 20 MHz 311 * ticf : I2C SCL falling time 312 * tr : I2C SCL rising time 313 * intd : LSI internal delay 314 * clkp : peripheral_clk 315 * F[] : integer up-valuation 316 */ 317 rate = clk_get_rate(priv->clk); 318 cdf = rate / 20000000; 319 cdf_width = (priv->devtype == I2C_RCAR_GEN1) ? 2 : 3; 320 if (cdf >= 1U << cdf_width) 321 goto err_no_val; 322 323 if (t.bus_freq_hz > I2C_MAX_FAST_MODE_FREQ && priv->devtype >= I2C_RCAR_GEN4) 324 priv->flags |= ID_P_FMPLUS; 325 else 326 priv->flags &= ~ID_P_FMPLUS; 327 328 /* On Gen3+, we use cdf only for the filters, not as a SCL divider */ 329 ick = rate / (priv->devtype < I2C_RCAR_GEN3 ? (cdf + 1) : 1); 330 331 /* 332 * It is impossible to calculate a large scale number on u32. Separate it. 333 * 334 * F[(ticf + tr + intd) * ick] with sum = (ticf + tr + intd) 335 * = F[sum * ick / 1000000000] 336 * = F[(ick / 1000000) * sum / 1000] 337 */ 338 sum = t.scl_fall_ns + t.scl_rise_ns + t.scl_int_delay_ns; 339 round = DIV_ROUND_CLOSEST(ick, 1000000); 340 round = DIV_ROUND_CLOSEST(round * sum, 1000); 341 342 if (priv->devtype < I2C_RCAR_GEN3) { 343 u32 scgd; 344 /* 345 * SCL = ick / (20 + 8 * SCGD + F[(ticf + tr + intd) * ick]) 346 * 20 + 8 * SCGD + F[...] = ick / SCL 347 * SCGD = ((ick / SCL) - 20 - F[...]) / 8 348 * Result (= SCL) should be less than bus_speed for hardware safety 349 */ 350 scgd = DIV_ROUND_UP(ick, t.bus_freq_hz ?: 1); 351 scgd = DIV_ROUND_UP(scgd - 20 - round, 8); 352 scl = ick / (20 + 8 * scgd + round); 353 354 if (scgd > 0x3f) 355 goto err_no_val; 356 357 dev_dbg(dev, "clk %u/%u(%lu), round %u, CDF: %u, SCGD: %u\n", 358 scl, t.bus_freq_hz, rate, round, cdf, scgd); 359 360 priv->icccr = scgd << cdf_width | cdf; 361 } else { 362 u32 x, sum_ratio = RCAR_SCHD_RATIO + RCAR_SCLD_RATIO; 363 /* 364 * SCLD/SCHD ratio and SMD default value are explained above 365 * where they are defined. With these definitions, we can compute 366 * x as a base value for the SCLD/SCHD ratio: 367 * 368 * SCL = clkp / (8 + 2 * SMD + SCLD + SCHD + F[(ticf + tr + intd) * clkp]) 369 * SCL = clkp / (8 + 2 * SMD + RCAR_SCLD_RATIO * x 370 * + RCAR_SCHD_RATIO * x + F[...]) 371 * 372 * with: sum_ratio = RCAR_SCLD_RATIO + RCAR_SCHD_RATIO 373 * 374 * SCL = clkp / (8 + 2 * smd + sum_ratio * x + F[...]) 375 * 8 + 2 * smd + sum_ratio * x + F[...] = clkp / SCL 376 * x = ((clkp / SCL) - 8 - 2 * smd - F[...]) / sum_ratio 377 */ 378 x = DIV_ROUND_UP(rate, t.bus_freq_hz ?: 1); 379 x = DIV_ROUND_UP(x - 8 - 2 * priv->smd - round, sum_ratio); 380 scl = rate / (8 + 2 * priv->smd + sum_ratio * x + round); 381 382 if (x == 0 || x * RCAR_SCLD_RATIO > 0xffff) 383 goto err_no_val; 384 385 priv->icccr = cdf; 386 priv->schd = RCAR_SCHD_RATIO * x; 387 priv->scld = RCAR_SCLD_RATIO * x; 388 if (priv->smd >= priv->schd) 389 priv->smd = priv->schd - 1; 390 391 dev_dbg(dev, "clk %u/%u(%lu), round %u, CDF: %u SCHD %u SCLD %u SMD %u\n", 392 scl, t.bus_freq_hz, rate, round, cdf, priv->schd, priv->scld, priv->smd); 393 } 394 395 return 0; 396 397 err_no_val: 398 dev_err(dev, "it is impossible to calculate best SCL\n"); 399 return -EINVAL; 400 } 401 402 /* 403 * We don't have a test case but the HW engineers say that the write order of 404 * ICMSR and ICMCR depends on whether we issue START or REP_START. So, ICMSR 405 * handling is outside of this function. First messages clear ICMSR before this 406 * function, interrupt handlers clear the relevant bits after this function. 407 */ 408 static void rcar_i2c_prepare_msg(struct rcar_i2c_priv *priv) 409 { 410 int read = !!rcar_i2c_is_recv(priv); 411 bool rep_start = !(priv->flags & ID_REP_AFTER_RD); 412 413 priv->pos = 0; 414 priv->flags &= ID_P_MASK; 415 416 if (priv->msgs_left == 1) 417 priv->flags |= ID_LAST_MSG; 418 419 rcar_i2c_write(priv, ICMAR, i2c_8bit_addr_from_msg(priv->msg)); 420 if (priv->flags & ID_P_NOT_ATOMIC) 421 rcar_i2c_write(priv, ICMIER, read ? RCAR_IRQ_RECV : RCAR_IRQ_SEND); 422 423 if (rep_start) 424 rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_START); 425 } 426 427 static void rcar_i2c_first_msg(struct rcar_i2c_priv *priv, 428 struct i2c_msg *msgs, int num) 429 { 430 priv->msg = msgs; 431 priv->msgs_left = num; 432 rcar_i2c_write(priv, ICMSR, 0); /* must be before preparing msg */ 433 rcar_i2c_prepare_msg(priv); 434 } 435 436 static void rcar_i2c_next_msg(struct rcar_i2c_priv *priv) 437 { 438 priv->msg++; 439 priv->msgs_left--; 440 rcar_i2c_prepare_msg(priv); 441 /* ICMSR handling must come afterwards in the irq handler */ 442 } 443 444 static void rcar_i2c_cleanup_dma(struct rcar_i2c_priv *priv, bool terminate) 445 { 446 struct dma_chan *chan = priv->dma_direction == DMA_FROM_DEVICE 447 ? priv->dma_rx : priv->dma_tx; 448 449 /* only allowed from thread context! */ 450 if (terminate) 451 dmaengine_terminate_sync(chan); 452 453 dma_unmap_single(chan->device->dev, sg_dma_address(&priv->sg), 454 sg_dma_len(&priv->sg), priv->dma_direction); 455 456 /* Gen3+ can only do one RXDMA per transfer and we just completed it */ 457 if (priv->devtype >= I2C_RCAR_GEN3 && 458 priv->dma_direction == DMA_FROM_DEVICE) 459 priv->flags |= ID_P_NO_RXDMA; 460 461 priv->dma_direction = DMA_NONE; 462 463 /* Disable DMA Master Received/Transmitted, must be last! */ 464 rcar_i2c_write(priv, ICDMAER, 0); 465 } 466 467 static void rcar_i2c_dma_callback(void *data) 468 { 469 struct rcar_i2c_priv *priv = data; 470 471 priv->pos += sg_dma_len(&priv->sg); 472 473 rcar_i2c_cleanup_dma(priv, false); 474 } 475 476 static bool rcar_i2c_dma(struct rcar_i2c_priv *priv) 477 { 478 struct device *dev = rcar_i2c_priv_to_dev(priv); 479 struct i2c_msg *msg = priv->msg; 480 bool read = msg->flags & I2C_M_RD; 481 enum dma_data_direction dir = read ? DMA_FROM_DEVICE : DMA_TO_DEVICE; 482 struct dma_chan *chan = read ? priv->dma_rx : priv->dma_tx; 483 struct dma_async_tx_descriptor *txdesc; 484 dma_addr_t dma_addr; 485 dma_cookie_t cookie; 486 unsigned char *buf; 487 int len; 488 489 /* Do various checks to see if DMA is feasible at all */ 490 if (!(priv->flags & ID_P_NOT_ATOMIC) || IS_ERR(chan) || msg->len < RCAR_MIN_DMA_LEN || 491 !(msg->flags & I2C_M_DMA_SAFE) || (read && priv->flags & ID_P_NO_RXDMA)) 492 return false; 493 494 if (read) { 495 /* 496 * The last two bytes needs to be fetched using PIO in 497 * order for the STOP phase to work. 498 */ 499 buf = priv->msg->buf; 500 len = priv->msg->len - 2; 501 } else { 502 /* 503 * First byte in message was sent using PIO. 504 */ 505 buf = priv->msg->buf + 1; 506 len = priv->msg->len - 1; 507 } 508 509 dma_addr = dma_map_single(chan->device->dev, buf, len, dir); 510 if (dma_mapping_error(chan->device->dev, dma_addr)) { 511 dev_dbg(dev, "dma map failed, using PIO\n"); 512 return false; 513 } 514 515 sg_dma_len(&priv->sg) = len; 516 sg_dma_address(&priv->sg) = dma_addr; 517 518 priv->dma_direction = dir; 519 520 txdesc = dmaengine_prep_slave_sg(chan, &priv->sg, 1, 521 read ? DMA_DEV_TO_MEM : DMA_MEM_TO_DEV, 522 DMA_PREP_INTERRUPT | DMA_CTRL_ACK); 523 if (!txdesc) { 524 dev_dbg(dev, "dma prep slave sg failed, using PIO\n"); 525 rcar_i2c_cleanup_dma(priv, false); 526 return false; 527 } 528 529 txdesc->callback = rcar_i2c_dma_callback; 530 txdesc->callback_param = priv; 531 532 cookie = dmaengine_submit(txdesc); 533 if (dma_submit_error(cookie)) { 534 dev_dbg(dev, "submitting dma failed, using PIO\n"); 535 rcar_i2c_cleanup_dma(priv, false); 536 return false; 537 } 538 539 /* Enable DMA Master Received/Transmitted */ 540 if (read) 541 rcar_i2c_write(priv, ICDMAER, RMDMAE); 542 else 543 rcar_i2c_write(priv, ICDMAER, TMDMAE); 544 545 dma_async_issue_pending(chan); 546 return true; 547 } 548 549 static void rcar_i2c_irq_send(struct rcar_i2c_priv *priv, u32 msr) 550 { 551 struct i2c_msg *msg = priv->msg; 552 u32 irqs_to_clear = MDE; 553 554 /* FIXME: sometimes, unknown interrupt happened. Do nothing */ 555 if (WARN(!(msr & MDE), "spurious irq")) 556 return; 557 558 if (msr & MAT) 559 irqs_to_clear |= MAT; 560 561 /* Check if DMA can be enabled and take over */ 562 if (priv->pos == 1 && rcar_i2c_dma(priv)) 563 return; 564 565 if (priv->pos < msg->len) { 566 /* 567 * Prepare next data to ICRXTX register. 568 * This data will go to _SHIFT_ register. 569 * 570 * * 571 * [ICRXTX] -> [SHIFT] -> [I2C bus] 572 */ 573 rcar_i2c_write(priv, ICRXTX, msg->buf[priv->pos]); 574 priv->pos++; 575 } else { 576 /* 577 * The last data was pushed to ICRXTX on _PREV_ empty irq. 578 * It is on _SHIFT_ register, and will sent to I2C bus. 579 * 580 * * 581 * [ICRXTX] -> [SHIFT] -> [I2C bus] 582 */ 583 584 if (priv->flags & ID_LAST_MSG) 585 /* 586 * If current msg is the _LAST_ msg, 587 * prepare stop condition here. 588 * ID_DONE will be set on STOP irq. 589 */ 590 rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_STOP); 591 else 592 rcar_i2c_next_msg(priv); 593 } 594 595 rcar_i2c_clear_irq(priv, irqs_to_clear); 596 } 597 598 static void rcar_i2c_irq_recv(struct rcar_i2c_priv *priv, u32 msr) 599 { 600 struct i2c_msg *msg = priv->msg; 601 bool recv_len_init = priv->pos == 0 && msg->flags & I2C_M_RECV_LEN; 602 u32 irqs_to_clear = MDR; 603 604 /* FIXME: sometimes, unknown interrupt happened. Do nothing */ 605 if (!(msr & MDR)) 606 return; 607 608 if (msr & MAT) { 609 irqs_to_clear |= MAT; 610 /* 611 * Address transfer phase finished, but no data at this point. 612 * Try to use DMA to receive data. 613 */ 614 rcar_i2c_dma(priv); 615 } else if (priv->pos < msg->len) { 616 /* get received data */ 617 u8 data = rcar_i2c_read(priv, ICRXTX); 618 619 msg->buf[priv->pos] = data; 620 if (recv_len_init) { 621 if (data == 0 || data > I2C_SMBUS_BLOCK_MAX) { 622 priv->flags |= ID_DONE | ID_EPROTO; 623 return; 624 } 625 msg->len += msg->buf[0]; 626 /* Enough data for DMA? */ 627 if (rcar_i2c_dma(priv)) 628 return; 629 /* new length after RECV_LEN now properly initialized */ 630 recv_len_init = false; 631 } 632 priv->pos++; 633 } 634 635 /* 636 * If next received data is the _LAST_ and we are not waiting for a new 637 * length because of RECV_LEN, then go to a new phase. 638 */ 639 if (priv->pos + 1 == msg->len && !recv_len_init) { 640 if (priv->flags & ID_LAST_MSG) { 641 rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_STOP); 642 } else { 643 rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_START); 644 priv->flags |= ID_REP_AFTER_RD; 645 } 646 } 647 648 if (priv->pos == msg->len && !(priv->flags & ID_LAST_MSG)) 649 rcar_i2c_next_msg(priv); 650 651 rcar_i2c_clear_irq(priv, irqs_to_clear); 652 } 653 654 static bool rcar_i2c_slave_irq(struct rcar_i2c_priv *priv) 655 { 656 u32 ssr_raw, ssr_filtered; 657 u8 value; 658 659 ssr_raw = rcar_i2c_read(priv, ICSSR) & 0xff; 660 ssr_filtered = ssr_raw & rcar_i2c_read(priv, ICSIER); 661 662 if (!ssr_filtered) 663 return false; 664 665 /* address detected */ 666 if (ssr_filtered & SAR) { 667 /* read or write request */ 668 if (ssr_raw & STM) { 669 i2c_slave_event(priv->slave, I2C_SLAVE_READ_REQUESTED, &value); 670 rcar_i2c_write(priv, ICRXTX, value); 671 rcar_i2c_write(priv, ICSIER, SDE | SSR | SAR); 672 } else { 673 i2c_slave_event(priv->slave, I2C_SLAVE_WRITE_REQUESTED, &value); 674 rcar_i2c_read(priv, ICRXTX); /* dummy read */ 675 rcar_i2c_write(priv, ICSIER, SDR | SSR | SAR); 676 } 677 678 /* Clear SSR, too, because of old STOPs to other clients than us */ 679 rcar_i2c_write(priv, ICSSR, ~(SAR | SSR) & 0xff); 680 } 681 682 /* master sent stop */ 683 if (ssr_filtered & SSR) { 684 i2c_slave_event(priv->slave, I2C_SLAVE_STOP, &value); 685 rcar_i2c_write(priv, ICSCR, SIE | SDBS); /* clear our NACK */ 686 rcar_i2c_write(priv, ICSIER, SAR); 687 rcar_i2c_write(priv, ICSSR, ~SSR & 0xff); 688 } 689 690 /* master wants to write to us */ 691 if (ssr_filtered & SDR) { 692 int ret; 693 694 value = rcar_i2c_read(priv, ICRXTX); 695 ret = i2c_slave_event(priv->slave, I2C_SLAVE_WRITE_RECEIVED, &value); 696 /* Send NACK in case of error */ 697 rcar_i2c_write(priv, ICSCR, SIE | SDBS | (ret < 0 ? FNA : 0)); 698 rcar_i2c_write(priv, ICSSR, ~SDR & 0xff); 699 } 700 701 /* master wants to read from us */ 702 if (ssr_filtered & SDE) { 703 i2c_slave_event(priv->slave, I2C_SLAVE_READ_PROCESSED, &value); 704 rcar_i2c_write(priv, ICRXTX, value); 705 rcar_i2c_write(priv, ICSSR, ~SDE & 0xff); 706 } 707 708 return true; 709 } 710 711 /* 712 * This driver has a lock-free design because there are IP cores (at least 713 * R-Car Gen2) which have an inherent race condition in their hardware design. 714 * There, we need to switch to RCAR_BUS_PHASE_DATA as soon as possible after 715 * the interrupt was generated, otherwise an unwanted repeated message gets 716 * generated. It turned out that taking a spinlock at the beginning of the ISR 717 * was already causing repeated messages. Thus, this driver was converted to 718 * the now lockless behaviour. Please keep this in mind when hacking the driver. 719 * R-Car Gen3 seems to have this fixed but earlier versions than R-Car Gen2 are 720 * likely affected. Therefore, we have different interrupt handler entries. 721 */ 722 static irqreturn_t rcar_i2c_irq(int irq, struct rcar_i2c_priv *priv, u32 msr) 723 { 724 if (!msr) { 725 if (rcar_i2c_slave_irq(priv)) 726 return IRQ_HANDLED; 727 728 return IRQ_NONE; 729 } 730 731 /* Arbitration lost */ 732 if (msr & MAL) { 733 priv->flags |= ID_DONE | ID_ARBLOST; 734 goto out; 735 } 736 737 /* Nack */ 738 if (msr & MNR) { 739 /* HW automatically sends STOP after received NACK */ 740 if (priv->flags & ID_P_NOT_ATOMIC) 741 rcar_i2c_write(priv, ICMIER, RCAR_IRQ_STOP); 742 priv->flags |= ID_NACK; 743 goto out; 744 } 745 746 /* Stop */ 747 if (msr & MST) { 748 priv->msgs_left--; /* The last message also made it */ 749 priv->flags |= ID_DONE; 750 goto out; 751 } 752 753 if (rcar_i2c_is_recv(priv)) 754 rcar_i2c_irq_recv(priv, msr); 755 else 756 rcar_i2c_irq_send(priv, msr); 757 758 out: 759 if (priv->flags & ID_DONE) { 760 rcar_i2c_write(priv, ICMIER, 0); 761 rcar_i2c_write(priv, ICMSR, 0); 762 if (priv->flags & ID_P_NOT_ATOMIC) 763 wake_up(&priv->wait); 764 } 765 766 return IRQ_HANDLED; 767 } 768 769 static irqreturn_t rcar_i2c_gen2_irq(int irq, void *ptr) 770 { 771 struct rcar_i2c_priv *priv = ptr; 772 u32 msr; 773 774 /* Clear START or STOP immediately, except for REPSTART after read */ 775 if (likely(!(priv->flags & ID_REP_AFTER_RD))) 776 rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_DATA); 777 778 /* Only handle interrupts that are currently enabled */ 779 msr = rcar_i2c_read(priv, ICMSR); 780 if (priv->flags & ID_P_NOT_ATOMIC) 781 msr &= rcar_i2c_read(priv, ICMIER); 782 783 return rcar_i2c_irq(irq, priv, msr); 784 } 785 786 static irqreturn_t rcar_i2c_gen3_irq(int irq, void *ptr) 787 { 788 struct rcar_i2c_priv *priv = ptr; 789 u32 msr; 790 791 /* Only handle interrupts that are currently enabled */ 792 msr = rcar_i2c_read(priv, ICMSR); 793 if (priv->flags & ID_P_NOT_ATOMIC) 794 msr &= rcar_i2c_read(priv, ICMIER); 795 796 /* 797 * Clear START or STOP immediately, except for REPSTART after read or 798 * if a spurious interrupt was detected. 799 */ 800 if (likely(!(priv->flags & ID_REP_AFTER_RD) && msr)) 801 rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_DATA); 802 803 return rcar_i2c_irq(irq, priv, msr); 804 } 805 806 static struct dma_chan *rcar_i2c_request_dma_chan(struct device *dev, 807 enum dma_transfer_direction dir, 808 dma_addr_t port_addr) 809 { 810 struct dma_chan *chan; 811 struct dma_slave_config cfg; 812 char *chan_name = dir == DMA_MEM_TO_DEV ? "tx" : "rx"; 813 int ret; 814 815 chan = dma_request_chan(dev, chan_name); 816 if (IS_ERR(chan)) { 817 dev_dbg(dev, "request_channel failed for %s (%ld)\n", 818 chan_name, PTR_ERR(chan)); 819 return chan; 820 } 821 822 memset(&cfg, 0, sizeof(cfg)); 823 cfg.direction = dir; 824 if (dir == DMA_MEM_TO_DEV) { 825 cfg.dst_addr = port_addr; 826 cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; 827 } else { 828 cfg.src_addr = port_addr; 829 cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; 830 } 831 832 ret = dmaengine_slave_config(chan, &cfg); 833 if (ret) { 834 dev_dbg(dev, "slave_config failed for %s (%d)\n", 835 chan_name, ret); 836 dma_release_channel(chan); 837 return ERR_PTR(ret); 838 } 839 840 dev_dbg(dev, "got DMA channel for %s\n", chan_name); 841 return chan; 842 } 843 844 static void rcar_i2c_request_dma(struct rcar_i2c_priv *priv, 845 struct i2c_msg *msg) 846 { 847 struct device *dev = rcar_i2c_priv_to_dev(priv); 848 bool read; 849 struct dma_chan *chan; 850 enum dma_transfer_direction dir; 851 852 read = msg->flags & I2C_M_RD; 853 854 chan = read ? priv->dma_rx : priv->dma_tx; 855 if (PTR_ERR(chan) != -EPROBE_DEFER) 856 return; 857 858 dir = read ? DMA_DEV_TO_MEM : DMA_MEM_TO_DEV; 859 chan = rcar_i2c_request_dma_chan(dev, dir, priv->res->start + ICRXTX); 860 861 if (read) 862 priv->dma_rx = chan; 863 else 864 priv->dma_tx = chan; 865 } 866 867 static void rcar_i2c_release_dma(struct rcar_i2c_priv *priv) 868 { 869 if (!IS_ERR(priv->dma_tx)) { 870 dma_release_channel(priv->dma_tx); 871 priv->dma_tx = ERR_PTR(-EPROBE_DEFER); 872 } 873 874 if (!IS_ERR(priv->dma_rx)) { 875 dma_release_channel(priv->dma_rx); 876 priv->dma_rx = ERR_PTR(-EPROBE_DEFER); 877 } 878 } 879 880 /* I2C is a special case, we need to poll the status of a reset */ 881 static int rcar_i2c_do_reset(struct rcar_i2c_priv *priv) 882 { 883 int ret; 884 885 /* Don't reset if a slave instance is currently running */ 886 if (priv->slave) 887 return -EISCONN; 888 889 ret = reset_control_reset(priv->rstc); 890 if (ret) 891 return ret; 892 893 return read_poll_timeout_atomic(reset_control_status, ret, ret == 0, 1, 894 100, false, priv->rstc); 895 } 896 897 static int rcar_i2c_master_xfer(struct i2c_adapter *adap, 898 struct i2c_msg *msgs, 899 int num) 900 { 901 struct rcar_i2c_priv *priv = i2c_get_adapdata(adap); 902 struct device *dev = rcar_i2c_priv_to_dev(priv); 903 int i, ret; 904 long time_left; 905 906 priv->flags |= ID_P_NOT_ATOMIC; 907 908 pm_runtime_get_sync(dev); 909 910 /* Check bus state before init otherwise bus busy info will be lost */ 911 ret = rcar_i2c_bus_barrier(priv); 912 if (ret < 0) 913 goto out; 914 915 /* Gen3+ needs a reset. That also allows RXDMA once */ 916 if (priv->devtype >= I2C_RCAR_GEN3) { 917 ret = rcar_i2c_do_reset(priv); 918 if (ret) 919 goto out; 920 priv->flags &= ~ID_P_NO_RXDMA; 921 } 922 923 rcar_i2c_init(priv); 924 925 for (i = 0; i < num; i++) 926 rcar_i2c_request_dma(priv, msgs + i); 927 928 rcar_i2c_first_msg(priv, msgs, num); 929 930 time_left = wait_event_timeout(priv->wait, priv->flags & ID_DONE, 931 num * adap->timeout); 932 933 /* cleanup DMA if it couldn't complete properly due to an error */ 934 if (priv->dma_direction != DMA_NONE) 935 rcar_i2c_cleanup_dma(priv, true); 936 937 if (!time_left) { 938 rcar_i2c_init(priv); 939 ret = -ETIMEDOUT; 940 } else if (priv->flags & ID_NACK) { 941 ret = -ENXIO; 942 } else if (priv->flags & ID_ARBLOST) { 943 ret = -EAGAIN; 944 } else if (priv->flags & ID_EPROTO) { 945 ret = -EPROTO; 946 } else { 947 ret = num - priv->msgs_left; /* The number of transfer */ 948 } 949 out: 950 pm_runtime_put(dev); 951 952 if (ret < 0 && ret != -ENXIO) 953 dev_err(dev, "error %d : %x\n", ret, priv->flags); 954 955 return ret; 956 } 957 958 static int rcar_i2c_master_xfer_atomic(struct i2c_adapter *adap, 959 struct i2c_msg *msgs, 960 int num) 961 { 962 struct rcar_i2c_priv *priv = i2c_get_adapdata(adap); 963 struct device *dev = rcar_i2c_priv_to_dev(priv); 964 unsigned long j; 965 bool time_left; 966 int ret; 967 968 priv->flags &= ~ID_P_NOT_ATOMIC; 969 970 pm_runtime_get_sync(dev); 971 972 /* Check bus state before init otherwise bus busy info will be lost */ 973 ret = rcar_i2c_bus_barrier(priv); 974 if (ret < 0) 975 goto out; 976 977 rcar_i2c_init(priv); 978 rcar_i2c_first_msg(priv, msgs, num); 979 980 j = jiffies + num * adap->timeout; 981 do { 982 u32 msr = rcar_i2c_read(priv, ICMSR); 983 984 msr &= (rcar_i2c_is_recv(priv) ? RCAR_IRQ_RECV : RCAR_IRQ_SEND) | RCAR_IRQ_STOP; 985 986 if (msr) { 987 if (priv->devtype < I2C_RCAR_GEN3) 988 rcar_i2c_gen2_irq(0, priv); 989 else 990 rcar_i2c_gen3_irq(0, priv); 991 } 992 993 time_left = time_before_eq(jiffies, j); 994 } while (!(priv->flags & ID_DONE) && time_left); 995 996 if (!time_left) { 997 rcar_i2c_init(priv); 998 ret = -ETIMEDOUT; 999 } else if (priv->flags & ID_NACK) { 1000 ret = -ENXIO; 1001 } else if (priv->flags & ID_ARBLOST) { 1002 ret = -EAGAIN; 1003 } else if (priv->flags & ID_EPROTO) { 1004 ret = -EPROTO; 1005 } else { 1006 ret = num - priv->msgs_left; /* The number of transfer */ 1007 } 1008 out: 1009 pm_runtime_put(dev); 1010 1011 if (ret < 0 && ret != -ENXIO) 1012 dev_err(dev, "error %d : %x\n", ret, priv->flags); 1013 1014 return ret; 1015 } 1016 1017 static int rcar_reg_slave(struct i2c_client *slave) 1018 { 1019 struct rcar_i2c_priv *priv = i2c_get_adapdata(slave->adapter); 1020 1021 if (priv->slave) 1022 return -EBUSY; 1023 1024 if (slave->flags & I2C_CLIENT_TEN) 1025 return -EAFNOSUPPORT; 1026 1027 /* Keep device active for slave address detection logic */ 1028 pm_runtime_get_sync(rcar_i2c_priv_to_dev(priv)); 1029 1030 priv->slave = slave; 1031 rcar_i2c_write(priv, ICSAR, slave->addr); 1032 rcar_i2c_write(priv, ICSSR, 0); 1033 rcar_i2c_write(priv, ICSIER, SAR); 1034 rcar_i2c_write(priv, ICSCR, SIE | SDBS); 1035 1036 return 0; 1037 } 1038 1039 static int rcar_unreg_slave(struct i2c_client *slave) 1040 { 1041 struct rcar_i2c_priv *priv = i2c_get_adapdata(slave->adapter); 1042 1043 WARN_ON(!priv->slave); 1044 1045 /* ensure no irq is running before clearing ptr */ 1046 disable_irq(priv->irq); 1047 rcar_i2c_reset_slave(priv); 1048 enable_irq(priv->irq); 1049 1050 priv->slave = NULL; 1051 1052 pm_runtime_put(rcar_i2c_priv_to_dev(priv)); 1053 1054 return 0; 1055 } 1056 1057 static u32 rcar_i2c_func(struct i2c_adapter *adap) 1058 { 1059 struct rcar_i2c_priv *priv = i2c_get_adapdata(adap); 1060 1061 /* 1062 * This HW can't do: 1063 * I2C_SMBUS_QUICK (setting FSB during START didn't work) 1064 * I2C_M_NOSTART (automatically sends address after START) 1065 * I2C_M_IGNORE_NAK (automatically sends STOP after NAK) 1066 */ 1067 u32 func = I2C_FUNC_I2C | I2C_FUNC_SLAVE | 1068 (I2C_FUNC_SMBUS_EMUL_ALL & ~I2C_FUNC_SMBUS_QUICK); 1069 1070 if (priv->flags & ID_P_HOST_NOTIFY) 1071 func |= I2C_FUNC_SMBUS_HOST_NOTIFY; 1072 1073 return func; 1074 } 1075 1076 static const struct i2c_algorithm rcar_i2c_algo = { 1077 .master_xfer = rcar_i2c_master_xfer, 1078 .master_xfer_atomic = rcar_i2c_master_xfer_atomic, 1079 .functionality = rcar_i2c_func, 1080 .reg_slave = rcar_reg_slave, 1081 .unreg_slave = rcar_unreg_slave, 1082 }; 1083 1084 static const struct i2c_adapter_quirks rcar_i2c_quirks = { 1085 .flags = I2C_AQ_NO_ZERO_LEN, 1086 }; 1087 1088 static const struct of_device_id rcar_i2c_dt_ids[] = { 1089 { .compatible = "renesas,i2c-r8a7778", .data = (void *)I2C_RCAR_GEN1 }, 1090 { .compatible = "renesas,i2c-r8a7779", .data = (void *)I2C_RCAR_GEN1 }, 1091 { .compatible = "renesas,i2c-r8a7790", .data = (void *)I2C_RCAR_GEN2 }, 1092 { .compatible = "renesas,i2c-r8a7791", .data = (void *)I2C_RCAR_GEN2 }, 1093 { .compatible = "renesas,i2c-r8a7792", .data = (void *)I2C_RCAR_GEN2 }, 1094 { .compatible = "renesas,i2c-r8a7793", .data = (void *)I2C_RCAR_GEN2 }, 1095 { .compatible = "renesas,i2c-r8a7794", .data = (void *)I2C_RCAR_GEN2 }, 1096 { .compatible = "renesas,i2c-r8a7795", .data = (void *)I2C_RCAR_GEN3 }, 1097 { .compatible = "renesas,i2c-r8a7796", .data = (void *)I2C_RCAR_GEN3 }, 1098 /* S4 has no FM+ bit */ 1099 { .compatible = "renesas,i2c-r8a779f0", .data = (void *)I2C_RCAR_GEN3 }, 1100 { .compatible = "renesas,rcar-gen1-i2c", .data = (void *)I2C_RCAR_GEN1 }, 1101 { .compatible = "renesas,rcar-gen2-i2c", .data = (void *)I2C_RCAR_GEN2 }, 1102 { .compatible = "renesas,rcar-gen3-i2c", .data = (void *)I2C_RCAR_GEN3 }, 1103 { .compatible = "renesas,rcar-gen4-i2c", .data = (void *)I2C_RCAR_GEN4 }, 1104 {}, 1105 }; 1106 MODULE_DEVICE_TABLE(of, rcar_i2c_dt_ids); 1107 1108 static int rcar_i2c_probe(struct platform_device *pdev) 1109 { 1110 struct rcar_i2c_priv *priv; 1111 struct i2c_adapter *adap; 1112 struct device *dev = &pdev->dev; 1113 unsigned long irqflags = 0; 1114 irqreturn_t (*irqhandler)(int irq, void *ptr) = rcar_i2c_gen3_irq; 1115 int ret; 1116 1117 /* Otherwise logic will break because some bytes must always use PIO */ 1118 BUILD_BUG_ON_MSG(RCAR_MIN_DMA_LEN < 3, "Invalid min DMA length"); 1119 1120 priv = devm_kzalloc(dev, sizeof(struct rcar_i2c_priv), GFP_KERNEL); 1121 if (!priv) 1122 return -ENOMEM; 1123 1124 priv->clk = devm_clk_get(dev, NULL); 1125 if (IS_ERR(priv->clk)) { 1126 dev_err(dev, "cannot get clock\n"); 1127 return PTR_ERR(priv->clk); 1128 } 1129 1130 priv->io = devm_platform_get_and_ioremap_resource(pdev, 0, &priv->res); 1131 if (IS_ERR(priv->io)) 1132 return PTR_ERR(priv->io); 1133 1134 priv->devtype = (enum rcar_i2c_type)of_device_get_match_data(dev); 1135 init_waitqueue_head(&priv->wait); 1136 1137 adap = &priv->adap; 1138 adap->nr = pdev->id; 1139 adap->algo = &rcar_i2c_algo; 1140 adap->class = I2C_CLASS_DEPRECATED; 1141 adap->retries = 3; 1142 adap->dev.parent = dev; 1143 adap->dev.of_node = dev->of_node; 1144 adap->bus_recovery_info = &rcar_i2c_bri; 1145 adap->quirks = &rcar_i2c_quirks; 1146 i2c_set_adapdata(adap, priv); 1147 strscpy(adap->name, pdev->name, sizeof(adap->name)); 1148 1149 /* Init DMA */ 1150 sg_init_table(&priv->sg, 1); 1151 priv->dma_direction = DMA_NONE; 1152 priv->dma_rx = priv->dma_tx = ERR_PTR(-EPROBE_DEFER); 1153 1154 /* Activate device for clock calculation */ 1155 pm_runtime_enable(dev); 1156 pm_runtime_get_sync(dev); 1157 ret = rcar_i2c_clock_calculate(priv); 1158 if (ret < 0) { 1159 pm_runtime_put(dev); 1160 goto out_pm_disable; 1161 } 1162 1163 /* Bring hardware to known state */ 1164 rcar_i2c_init(priv); 1165 rcar_i2c_reset_slave(priv); 1166 1167 /* Stay always active when multi-master to keep arbitration working */ 1168 if (of_property_read_bool(dev->of_node, "multi-master")) 1169 priv->flags |= ID_P_PM_BLOCKED; 1170 else 1171 pm_runtime_put(dev); 1172 1173 if (of_property_read_bool(dev->of_node, "smbus")) 1174 priv->flags |= ID_P_HOST_NOTIFY; 1175 1176 if (priv->devtype < I2C_RCAR_GEN3) { 1177 irqflags |= IRQF_NO_THREAD; 1178 irqhandler = rcar_i2c_gen2_irq; 1179 } else { 1180 /* R-Car Gen3+ needs a reset before every transfer */ 1181 priv->rstc = devm_reset_control_get_exclusive(&pdev->dev, NULL); 1182 if (IS_ERR(priv->rstc)) { 1183 ret = PTR_ERR(priv->rstc); 1184 goto out_pm_put; 1185 } 1186 1187 ret = reset_control_status(priv->rstc); 1188 if (ret < 0) 1189 goto out_pm_put; 1190 1191 /* hard reset disturbs HostNotify local target, so disable it */ 1192 priv->flags &= ~ID_P_HOST_NOTIFY; 1193 } 1194 1195 ret = platform_get_irq(pdev, 0); 1196 if (ret < 0) 1197 goto out_pm_put; 1198 priv->irq = ret; 1199 ret = devm_request_irq(dev, priv->irq, irqhandler, irqflags, dev_name(dev), priv); 1200 if (ret < 0) { 1201 dev_err(dev, "cannot get irq %d\n", priv->irq); 1202 goto out_pm_put; 1203 } 1204 1205 platform_set_drvdata(pdev, priv); 1206 1207 ret = i2c_add_numbered_adapter(adap); 1208 if (ret < 0) 1209 goto out_pm_put; 1210 1211 if (priv->flags & ID_P_HOST_NOTIFY) { 1212 priv->host_notify_client = i2c_new_slave_host_notify_device(adap); 1213 if (IS_ERR(priv->host_notify_client)) { 1214 ret = PTR_ERR(priv->host_notify_client); 1215 goto out_del_device; 1216 } 1217 } 1218 1219 dev_info(dev, "probed\n"); 1220 1221 return 0; 1222 1223 out_del_device: 1224 i2c_del_adapter(&priv->adap); 1225 out_pm_put: 1226 if (priv->flags & ID_P_PM_BLOCKED) 1227 pm_runtime_put(dev); 1228 out_pm_disable: 1229 pm_runtime_disable(dev); 1230 return ret; 1231 } 1232 1233 static void rcar_i2c_remove(struct platform_device *pdev) 1234 { 1235 struct rcar_i2c_priv *priv = platform_get_drvdata(pdev); 1236 struct device *dev = &pdev->dev; 1237 1238 if (priv->host_notify_client) 1239 i2c_free_slave_host_notify_device(priv->host_notify_client); 1240 i2c_del_adapter(&priv->adap); 1241 rcar_i2c_release_dma(priv); 1242 if (priv->flags & ID_P_PM_BLOCKED) 1243 pm_runtime_put(dev); 1244 pm_runtime_disable(dev); 1245 } 1246 1247 static int rcar_i2c_suspend(struct device *dev) 1248 { 1249 struct rcar_i2c_priv *priv = dev_get_drvdata(dev); 1250 1251 i2c_mark_adapter_suspended(&priv->adap); 1252 return 0; 1253 } 1254 1255 static int rcar_i2c_resume(struct device *dev) 1256 { 1257 struct rcar_i2c_priv *priv = dev_get_drvdata(dev); 1258 1259 i2c_mark_adapter_resumed(&priv->adap); 1260 return 0; 1261 } 1262 1263 static const struct dev_pm_ops rcar_i2c_pm_ops = { 1264 NOIRQ_SYSTEM_SLEEP_PM_OPS(rcar_i2c_suspend, rcar_i2c_resume) 1265 }; 1266 1267 static struct platform_driver rcar_i2c_driver = { 1268 .driver = { 1269 .name = "i2c-rcar", 1270 .of_match_table = rcar_i2c_dt_ids, 1271 .pm = pm_sleep_ptr(&rcar_i2c_pm_ops), 1272 }, 1273 .probe = rcar_i2c_probe, 1274 .remove = rcar_i2c_remove, 1275 }; 1276 1277 module_platform_driver(rcar_i2c_driver); 1278 1279 MODULE_LICENSE("GPL v2"); 1280 MODULE_DESCRIPTION("Renesas R-Car I2C bus driver"); 1281 MODULE_AUTHOR("Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>"); 1282