1 /* 2 * I2C adapter for the IMG Serial Control Bus (SCB) IP block. 3 * 4 * Copyright (C) 2009, 2010, 2012, 2014 Imagination Technologies Ltd. 5 * 6 * This program is free software; you can redistribute it and/or modify 7 * it under the terms of the GNU General Public License version 2 as 8 * published by the Free Software Foundation. 9 * 10 * There are three ways that this I2C controller can be driven: 11 * 12 * - Raw control of the SDA and SCK signals. 13 * 14 * This corresponds to MODE_RAW, which takes control of the signals 15 * directly for a certain number of clock cycles (the INT_TIMING 16 * interrupt can be used for timing). 17 * 18 * - Atomic commands. A low level I2C symbol (such as generate 19 * start/stop/ack/nack bit, generate byte, receive byte, and receive 20 * ACK) is given to the hardware, with detection of completion by bits 21 * in the LINESTAT register. 22 * 23 * This mode of operation is used by MODE_ATOMIC, which uses an I2C 24 * state machine in the interrupt handler to compose/react to I2C 25 * transactions using atomic mode commands, and also by MODE_SEQUENCE, 26 * which emits a simple fixed sequence of atomic mode commands. 27 * 28 * Due to software control, the use of atomic commands usually results 29 * in suboptimal use of the bus, with gaps between the I2C symbols while 30 * the driver decides what to do next. 31 * 32 * - Automatic mode. A bus address, and whether to read/write is 33 * specified, and the hardware takes care of the I2C state machine, 34 * using a FIFO to send/receive bytes of data to an I2C slave. The 35 * driver just has to keep the FIFO drained or filled in response to the 36 * appropriate FIFO interrupts. 37 * 38 * This corresponds to MODE_AUTOMATIC, which manages the FIFOs and deals 39 * with control of repeated start bits between I2C messages. 40 * 41 * Use of automatic mode and the FIFO can make much more efficient use 42 * of the bus compared to individual atomic commands, with potentially 43 * no wasted time between I2C symbols or I2C messages. 44 * 45 * In most cases MODE_AUTOMATIC is used, however if any of the messages in 46 * a transaction are zero byte writes (e.g. used by i2cdetect for probing 47 * the bus), MODE_ATOMIC must be used since automatic mode is normally 48 * started by the writing of data into the FIFO. 49 * 50 * The other modes are used in specific circumstances where MODE_ATOMIC and 51 * MODE_AUTOMATIC aren't appropriate. MODE_RAW is used to implement a bus 52 * recovery routine. MODE_SEQUENCE is used to reset the bus and make sure 53 * it is in a sane state. 54 * 55 * Notice that the driver implements a timer-based timeout mechanism. 56 * The reason for this mechanism is to reduce the number of interrupts 57 * received in automatic mode. 58 * 59 * The driver would get a slave event and transaction done interrupts for 60 * each atomic mode command that gets completed. However, these events are 61 * not needed in automatic mode, becase those atomic mode commands are 62 * managed automatically by the hardware. 63 * 64 * In practice, normal I2C transactions will be complete well before you 65 * get the timer interrupt, as the timer is re-scheduled during FIFO 66 * maintenance and disabled after the transaction is complete. 67 * 68 * In this way normal automatic mode operation isn't impacted by 69 * unnecessary interrupts, but the exceptional abort condition can still be 70 * detected (with a slight delay). 71 */ 72 73 #include <linux/bitops.h> 74 #include <linux/clk.h> 75 #include <linux/completion.h> 76 #include <linux/err.h> 77 #include <linux/i2c.h> 78 #include <linux/init.h> 79 #include <linux/interrupt.h> 80 #include <linux/io.h> 81 #include <linux/kernel.h> 82 #include <linux/module.h> 83 #include <linux/of_platform.h> 84 #include <linux/platform_device.h> 85 #include <linux/slab.h> 86 #include <linux/timer.h> 87 88 /* Register offsets */ 89 90 #define SCB_STATUS_REG 0x00 91 #define SCB_OVERRIDE_REG 0x04 92 #define SCB_READ_ADDR_REG 0x08 93 #define SCB_READ_COUNT_REG 0x0c 94 #define SCB_WRITE_ADDR_REG 0x10 95 #define SCB_READ_DATA_REG 0x14 96 #define SCB_WRITE_DATA_REG 0x18 97 #define SCB_FIFO_STATUS_REG 0x1c 98 #define SCB_CONTROL_SOFT_RESET 0x1f 99 #define SCB_CLK_SET_REG 0x3c 100 #define SCB_INT_STATUS_REG 0x40 101 #define SCB_INT_CLEAR_REG 0x44 102 #define SCB_INT_MASK_REG 0x48 103 #define SCB_CONTROL_REG 0x4c 104 #define SCB_TIME_TPL_REG 0x50 105 #define SCB_TIME_TPH_REG 0x54 106 #define SCB_TIME_TP2S_REG 0x58 107 #define SCB_TIME_TBI_REG 0x60 108 #define SCB_TIME_TSL_REG 0x64 109 #define SCB_TIME_TDL_REG 0x68 110 #define SCB_TIME_TSDL_REG 0x6c 111 #define SCB_TIME_TSDH_REG 0x70 112 #define SCB_READ_XADDR_REG 0x74 113 #define SCB_WRITE_XADDR_REG 0x78 114 #define SCB_WRITE_COUNT_REG 0x7c 115 #define SCB_CORE_REV_REG 0x80 116 #define SCB_TIME_TCKH_REG 0x84 117 #define SCB_TIME_TCKL_REG 0x88 118 #define SCB_FIFO_FLUSH_REG 0x8c 119 #define SCB_READ_FIFO_REG 0x94 120 #define SCB_CLEAR_REG 0x98 121 122 /* SCB_CONTROL_REG bits */ 123 124 #define SCB_CONTROL_CLK_ENABLE 0x1e0 125 #define SCB_CONTROL_TRANSACTION_HALT 0x200 126 127 #define FIFO_READ_FULL BIT(0) 128 #define FIFO_READ_EMPTY BIT(1) 129 #define FIFO_WRITE_FULL BIT(2) 130 #define FIFO_WRITE_EMPTY BIT(3) 131 132 /* SCB_CLK_SET_REG bits */ 133 #define SCB_FILT_DISABLE BIT(31) 134 #define SCB_FILT_BYPASS BIT(30) 135 #define SCB_FILT_INC_MASK 0x7f 136 #define SCB_FILT_INC_SHIFT 16 137 #define SCB_INC_MASK 0x7f 138 #define SCB_INC_SHIFT 8 139 140 /* SCB_INT_*_REG bits */ 141 142 #define INT_BUS_INACTIVE BIT(0) 143 #define INT_UNEXPECTED_START BIT(1) 144 #define INT_SCLK_LOW_TIMEOUT BIT(2) 145 #define INT_SDAT_LOW_TIMEOUT BIT(3) 146 #define INT_WRITE_ACK_ERR BIT(4) 147 #define INT_ADDR_ACK_ERR BIT(5) 148 #define INT_FIFO_FULL BIT(9) 149 #define INT_FIFO_FILLING BIT(10) 150 #define INT_FIFO_EMPTY BIT(11) 151 #define INT_FIFO_EMPTYING BIT(12) 152 #define INT_TRANSACTION_DONE BIT(15) 153 #define INT_SLAVE_EVENT BIT(16) 154 #define INT_TIMING BIT(18) 155 156 #define INT_FIFO_FULL_FILLING (INT_FIFO_FULL | INT_FIFO_FILLING) 157 #define INT_FIFO_EMPTY_EMPTYING (INT_FIFO_EMPTY | INT_FIFO_EMPTYING) 158 159 /* Level interrupts need clearing after handling instead of before */ 160 #define INT_LEVEL 0x01e00 161 162 /* Don't allow any interrupts while the clock may be off */ 163 #define INT_ENABLE_MASK_INACTIVE 0x00000 164 165 /* Interrupt masks for the different driver modes */ 166 167 #define INT_ENABLE_MASK_RAW INT_TIMING 168 169 #define INT_ENABLE_MASK_ATOMIC (INT_TRANSACTION_DONE | \ 170 INT_SLAVE_EVENT | \ 171 INT_ADDR_ACK_ERR | \ 172 INT_WRITE_ACK_ERR) 173 174 #define INT_ENABLE_MASK_AUTOMATIC (INT_SCLK_LOW_TIMEOUT | \ 175 INT_ADDR_ACK_ERR | \ 176 INT_WRITE_ACK_ERR | \ 177 INT_FIFO_FULL | \ 178 INT_FIFO_FILLING | \ 179 INT_FIFO_EMPTY | \ 180 INT_FIFO_EMPTYING) 181 182 #define INT_ENABLE_MASK_WAITSTOP (INT_SLAVE_EVENT | \ 183 INT_ADDR_ACK_ERR | \ 184 INT_WRITE_ACK_ERR) 185 186 /* SCB_STATUS_REG fields */ 187 188 #define LINESTAT_SCLK_LINE_STATUS BIT(0) 189 #define LINESTAT_SCLK_EN BIT(1) 190 #define LINESTAT_SDAT_LINE_STATUS BIT(2) 191 #define LINESTAT_SDAT_EN BIT(3) 192 #define LINESTAT_DET_START_STATUS BIT(4) 193 #define LINESTAT_DET_STOP_STATUS BIT(5) 194 #define LINESTAT_DET_ACK_STATUS BIT(6) 195 #define LINESTAT_DET_NACK_STATUS BIT(7) 196 #define LINESTAT_BUS_IDLE BIT(8) 197 #define LINESTAT_T_DONE_STATUS BIT(9) 198 #define LINESTAT_SCLK_OUT_STATUS BIT(10) 199 #define LINESTAT_SDAT_OUT_STATUS BIT(11) 200 #define LINESTAT_GEN_LINE_MASK_STATUS BIT(12) 201 #define LINESTAT_START_BIT_DET BIT(13) 202 #define LINESTAT_STOP_BIT_DET BIT(14) 203 #define LINESTAT_ACK_DET BIT(15) 204 #define LINESTAT_NACK_DET BIT(16) 205 #define LINESTAT_INPUT_HELD_V BIT(17) 206 #define LINESTAT_ABORT_DET BIT(18) 207 #define LINESTAT_ACK_OR_NACK_DET (LINESTAT_ACK_DET | LINESTAT_NACK_DET) 208 #define LINESTAT_INPUT_DATA 0xff000000 209 #define LINESTAT_INPUT_DATA_SHIFT 24 210 211 #define LINESTAT_CLEAR_SHIFT 13 212 #define LINESTAT_LATCHED (0x3f << LINESTAT_CLEAR_SHIFT) 213 214 /* SCB_OVERRIDE_REG fields */ 215 216 #define OVERRIDE_SCLK_OVR BIT(0) 217 #define OVERRIDE_SCLKEN_OVR BIT(1) 218 #define OVERRIDE_SDAT_OVR BIT(2) 219 #define OVERRIDE_SDATEN_OVR BIT(3) 220 #define OVERRIDE_MASTER BIT(9) 221 #define OVERRIDE_LINE_OVR_EN BIT(10) 222 #define OVERRIDE_DIRECT BIT(11) 223 #define OVERRIDE_CMD_SHIFT 4 224 #define OVERRIDE_CMD_MASK 0x1f 225 #define OVERRIDE_DATA_SHIFT 24 226 227 #define OVERRIDE_SCLK_DOWN (OVERRIDE_LINE_OVR_EN | \ 228 OVERRIDE_SCLKEN_OVR) 229 #define OVERRIDE_SCLK_UP (OVERRIDE_LINE_OVR_EN | \ 230 OVERRIDE_SCLKEN_OVR | \ 231 OVERRIDE_SCLK_OVR) 232 #define OVERRIDE_SDAT_DOWN (OVERRIDE_LINE_OVR_EN | \ 233 OVERRIDE_SDATEN_OVR) 234 #define OVERRIDE_SDAT_UP (OVERRIDE_LINE_OVR_EN | \ 235 OVERRIDE_SDATEN_OVR | \ 236 OVERRIDE_SDAT_OVR) 237 238 /* OVERRIDE_CMD values */ 239 240 #define CMD_PAUSE 0x00 241 #define CMD_GEN_DATA 0x01 242 #define CMD_GEN_START 0x02 243 #define CMD_GEN_STOP 0x03 244 #define CMD_GEN_ACK 0x04 245 #define CMD_GEN_NACK 0x05 246 #define CMD_RET_DATA 0x08 247 #define CMD_RET_ACK 0x09 248 249 /* Fixed timing values */ 250 251 #define TIMEOUT_TBI 0x0 252 #define TIMEOUT_TSL 0xffff 253 #define TIMEOUT_TDL 0x0 254 255 /* Transaction timeout */ 256 257 #define IMG_I2C_TIMEOUT (msecs_to_jiffies(1000)) 258 259 /* 260 * Worst incs are 1 (innacurate) and 16*256 (irregular). 261 * So a sensible inc is the logarithmic mean: 64 (2^6), which is 262 * in the middle of the valid range (0-127). 263 */ 264 #define SCB_OPT_INC 64 265 266 /* Setup the clock enable filtering for 25 ns */ 267 #define SCB_FILT_GLITCH 25 268 269 /* 270 * Bits to return from interrupt handler functions for different modes. 271 * This delays completion until we've finished with the registers, so that the 272 * function waiting for completion can safely disable the clock to save power. 273 */ 274 #define ISR_COMPLETE_M BIT(31) 275 #define ISR_FATAL_M BIT(30) 276 #define ISR_WAITSTOP BIT(29) 277 #define ISR_STATUS_M 0x0000ffff /* contains +ve errno */ 278 #define ISR_COMPLETE(err) (ISR_COMPLETE_M | (ISR_STATUS_M & (err))) 279 #define ISR_FATAL(err) (ISR_COMPLETE(err) | ISR_FATAL_M) 280 281 #define REL_SOC_IP_SCB_2_2_1 0x00020201 282 283 enum img_i2c_mode { 284 MODE_INACTIVE, 285 MODE_RAW, 286 MODE_ATOMIC, 287 MODE_AUTOMATIC, 288 MODE_SEQUENCE, 289 MODE_FATAL, 290 MODE_WAITSTOP, 291 MODE_SUSPEND, 292 }; 293 294 /* Timing parameters for i2c modes (in ns) */ 295 struct img_i2c_timings { 296 const char *name; 297 unsigned int max_bitrate; 298 unsigned int tckh, tckl, tsdh, tsdl; 299 unsigned int tp2s, tpl, tph; 300 }; 301 302 /* The timings array must be ordered from slower to faster */ 303 static struct img_i2c_timings timings[] = { 304 /* Standard mode */ 305 { 306 .name = "standard", 307 .max_bitrate = 100000, 308 .tckh = 4000, 309 .tckl = 4700, 310 .tsdh = 4700, 311 .tsdl = 8700, 312 .tp2s = 4700, 313 .tpl = 4700, 314 .tph = 4000, 315 }, 316 /* Fast mode */ 317 { 318 .name = "fast", 319 .max_bitrate = 400000, 320 .tckh = 600, 321 .tckl = 1300, 322 .tsdh = 600, 323 .tsdl = 1200, 324 .tp2s = 1300, 325 .tpl = 600, 326 .tph = 600, 327 }, 328 }; 329 330 /* Reset dance */ 331 static u8 img_i2c_reset_seq[] = { CMD_GEN_START, 332 CMD_GEN_DATA, 0xff, 333 CMD_RET_ACK, 334 CMD_GEN_START, 335 CMD_GEN_STOP, 336 0 }; 337 /* Just issue a stop (after an abort condition) */ 338 static u8 img_i2c_stop_seq[] = { CMD_GEN_STOP, 339 0 }; 340 341 /* We're interested in different interrupts depending on the mode */ 342 static unsigned int img_i2c_int_enable_by_mode[] = { 343 [MODE_INACTIVE] = INT_ENABLE_MASK_INACTIVE, 344 [MODE_RAW] = INT_ENABLE_MASK_RAW, 345 [MODE_ATOMIC] = INT_ENABLE_MASK_ATOMIC, 346 [MODE_AUTOMATIC] = INT_ENABLE_MASK_AUTOMATIC, 347 [MODE_SEQUENCE] = INT_ENABLE_MASK_ATOMIC, 348 [MODE_FATAL] = 0, 349 [MODE_WAITSTOP] = INT_ENABLE_MASK_WAITSTOP, 350 [MODE_SUSPEND] = 0, 351 }; 352 353 /* Atomic command names */ 354 static const char * const img_i2c_atomic_cmd_names[] = { 355 [CMD_PAUSE] = "PAUSE", 356 [CMD_GEN_DATA] = "GEN_DATA", 357 [CMD_GEN_START] = "GEN_START", 358 [CMD_GEN_STOP] = "GEN_STOP", 359 [CMD_GEN_ACK] = "GEN_ACK", 360 [CMD_GEN_NACK] = "GEN_NACK", 361 [CMD_RET_DATA] = "RET_DATA", 362 [CMD_RET_ACK] = "RET_ACK", 363 }; 364 365 struct img_i2c { 366 struct i2c_adapter adap; 367 368 void __iomem *base; 369 370 /* 371 * The scb core clock is used to get the input frequency, and to disable 372 * it after every set of transactions to save some power. 373 */ 374 struct clk *scb_clk, *sys_clk; 375 unsigned int bitrate; 376 bool need_wr_rd_fence; 377 378 /* state */ 379 struct completion msg_complete; 380 spinlock_t lock; /* lock before doing anything with the state */ 381 struct i2c_msg msg; 382 383 /* After the last transaction, wait for a stop bit */ 384 bool last_msg; 385 int msg_status; 386 387 enum img_i2c_mode mode; 388 u32 int_enable; /* depends on mode */ 389 u32 line_status; /* line status over command */ 390 391 /* 392 * To avoid slave event interrupts in automatic mode, use a timer to 393 * poll the abort condition if we don't get an interrupt for too long. 394 */ 395 struct timer_list check_timer; 396 bool t_halt; 397 398 /* atomic mode state */ 399 bool at_t_done; 400 bool at_slave_event; 401 int at_cur_cmd; 402 u8 at_cur_data; 403 404 /* Sequence: either reset or stop. See img_i2c_sequence. */ 405 u8 *seq; 406 407 /* raw mode */ 408 unsigned int raw_timeout; 409 }; 410 411 static void img_i2c_writel(struct img_i2c *i2c, u32 offset, u32 value) 412 { 413 writel(value, i2c->base + offset); 414 } 415 416 static u32 img_i2c_readl(struct img_i2c *i2c, u32 offset) 417 { 418 return readl(i2c->base + offset); 419 } 420 421 /* 422 * The code to read from the master read fifo, and write to the master 423 * write fifo, checks a bit in an SCB register before every byte to 424 * ensure that the fifo is not full (write fifo) or empty (read fifo). 425 * Due to clock domain crossing inside the SCB block the updated value 426 * of this bit is only visible after 2 cycles. 427 * 428 * The scb_wr_rd_fence() function does 2 dummy writes (to the read-only 429 * revision register), and it's called after reading from or writing to the 430 * fifos to ensure that subsequent reads of the fifo status bits do not read 431 * stale values. 432 */ 433 static void img_i2c_wr_rd_fence(struct img_i2c *i2c) 434 { 435 if (i2c->need_wr_rd_fence) { 436 img_i2c_writel(i2c, SCB_CORE_REV_REG, 0); 437 img_i2c_writel(i2c, SCB_CORE_REV_REG, 0); 438 } 439 } 440 441 static void img_i2c_switch_mode(struct img_i2c *i2c, enum img_i2c_mode mode) 442 { 443 i2c->mode = mode; 444 i2c->int_enable = img_i2c_int_enable_by_mode[mode]; 445 i2c->line_status = 0; 446 } 447 448 static void img_i2c_raw_op(struct img_i2c *i2c) 449 { 450 i2c->raw_timeout = 0; 451 img_i2c_writel(i2c, SCB_OVERRIDE_REG, 452 OVERRIDE_SCLKEN_OVR | 453 OVERRIDE_SDATEN_OVR | 454 OVERRIDE_MASTER | 455 OVERRIDE_LINE_OVR_EN | 456 OVERRIDE_DIRECT | 457 ((i2c->at_cur_cmd & OVERRIDE_CMD_MASK) << OVERRIDE_CMD_SHIFT) | 458 (i2c->at_cur_data << OVERRIDE_DATA_SHIFT)); 459 } 460 461 static const char *img_i2c_atomic_op_name(unsigned int cmd) 462 { 463 if (unlikely(cmd >= ARRAY_SIZE(img_i2c_atomic_cmd_names))) 464 return "UNKNOWN"; 465 return img_i2c_atomic_cmd_names[cmd]; 466 } 467 468 /* Send a single atomic mode command to the hardware */ 469 static void img_i2c_atomic_op(struct img_i2c *i2c, int cmd, u8 data) 470 { 471 i2c->at_cur_cmd = cmd; 472 i2c->at_cur_data = data; 473 474 /* work around lack of data setup time when generating data */ 475 if (cmd == CMD_GEN_DATA && i2c->mode == MODE_ATOMIC) { 476 u32 line_status = img_i2c_readl(i2c, SCB_STATUS_REG); 477 478 if (line_status & LINESTAT_SDAT_LINE_STATUS && !(data & 0x80)) { 479 /* hold the data line down for a moment */ 480 img_i2c_switch_mode(i2c, MODE_RAW); 481 img_i2c_raw_op(i2c); 482 return; 483 } 484 } 485 486 dev_dbg(i2c->adap.dev.parent, 487 "atomic cmd=%s (%d) data=%#x\n", 488 img_i2c_atomic_op_name(cmd), cmd, data); 489 i2c->at_t_done = (cmd == CMD_RET_DATA || cmd == CMD_RET_ACK); 490 i2c->at_slave_event = false; 491 i2c->line_status = 0; 492 493 img_i2c_writel(i2c, SCB_OVERRIDE_REG, 494 ((cmd & OVERRIDE_CMD_MASK) << OVERRIDE_CMD_SHIFT) | 495 OVERRIDE_MASTER | 496 OVERRIDE_DIRECT | 497 (data << OVERRIDE_DATA_SHIFT)); 498 } 499 500 /* Start a transaction in atomic mode */ 501 static void img_i2c_atomic_start(struct img_i2c *i2c) 502 { 503 img_i2c_switch_mode(i2c, MODE_ATOMIC); 504 img_i2c_writel(i2c, SCB_INT_MASK_REG, i2c->int_enable); 505 img_i2c_atomic_op(i2c, CMD_GEN_START, 0x00); 506 } 507 508 static void img_i2c_soft_reset(struct img_i2c *i2c) 509 { 510 i2c->t_halt = false; 511 img_i2c_writel(i2c, SCB_CONTROL_REG, 0); 512 img_i2c_writel(i2c, SCB_CONTROL_REG, 513 SCB_CONTROL_CLK_ENABLE | SCB_CONTROL_SOFT_RESET); 514 } 515 516 /* enable or release transaction halt for control of repeated starts */ 517 static void img_i2c_transaction_halt(struct img_i2c *i2c, bool t_halt) 518 { 519 u32 val; 520 521 if (i2c->t_halt == t_halt) 522 return; 523 i2c->t_halt = t_halt; 524 val = img_i2c_readl(i2c, SCB_CONTROL_REG); 525 if (t_halt) 526 val |= SCB_CONTROL_TRANSACTION_HALT; 527 else 528 val &= ~SCB_CONTROL_TRANSACTION_HALT; 529 img_i2c_writel(i2c, SCB_CONTROL_REG, val); 530 } 531 532 /* Drain data from the FIFO into the buffer (automatic mode) */ 533 static void img_i2c_read_fifo(struct img_i2c *i2c) 534 { 535 while (i2c->msg.len) { 536 u32 fifo_status; 537 u8 data; 538 539 fifo_status = img_i2c_readl(i2c, SCB_FIFO_STATUS_REG); 540 if (fifo_status & FIFO_READ_EMPTY) 541 break; 542 543 data = img_i2c_readl(i2c, SCB_READ_DATA_REG); 544 *i2c->msg.buf = data; 545 546 img_i2c_writel(i2c, SCB_READ_FIFO_REG, 0xff); 547 img_i2c_wr_rd_fence(i2c); 548 i2c->msg.len--; 549 i2c->msg.buf++; 550 } 551 } 552 553 /* Fill the FIFO with data from the buffer (automatic mode) */ 554 static void img_i2c_write_fifo(struct img_i2c *i2c) 555 { 556 while (i2c->msg.len) { 557 u32 fifo_status; 558 559 fifo_status = img_i2c_readl(i2c, SCB_FIFO_STATUS_REG); 560 if (fifo_status & FIFO_WRITE_FULL) 561 break; 562 563 img_i2c_writel(i2c, SCB_WRITE_DATA_REG, *i2c->msg.buf); 564 img_i2c_wr_rd_fence(i2c); 565 i2c->msg.len--; 566 i2c->msg.buf++; 567 } 568 569 /* Disable fifo emptying interrupt if nothing more to write */ 570 if (!i2c->msg.len) 571 i2c->int_enable &= ~INT_FIFO_EMPTYING; 572 } 573 574 /* Start a read transaction in automatic mode */ 575 static void img_i2c_read(struct img_i2c *i2c) 576 { 577 img_i2c_switch_mode(i2c, MODE_AUTOMATIC); 578 if (!i2c->last_msg) 579 i2c->int_enable |= INT_SLAVE_EVENT; 580 581 img_i2c_writel(i2c, SCB_INT_MASK_REG, i2c->int_enable); 582 img_i2c_writel(i2c, SCB_READ_ADDR_REG, i2c->msg.addr); 583 img_i2c_writel(i2c, SCB_READ_COUNT_REG, i2c->msg.len); 584 585 img_i2c_transaction_halt(i2c, false); 586 mod_timer(&i2c->check_timer, jiffies + msecs_to_jiffies(1)); 587 } 588 589 /* Start a write transaction in automatic mode */ 590 static void img_i2c_write(struct img_i2c *i2c) 591 { 592 img_i2c_switch_mode(i2c, MODE_AUTOMATIC); 593 if (!i2c->last_msg) 594 i2c->int_enable |= INT_SLAVE_EVENT; 595 596 img_i2c_writel(i2c, SCB_WRITE_ADDR_REG, i2c->msg.addr); 597 img_i2c_writel(i2c, SCB_WRITE_COUNT_REG, i2c->msg.len); 598 599 img_i2c_transaction_halt(i2c, false); 600 mod_timer(&i2c->check_timer, jiffies + msecs_to_jiffies(1)); 601 img_i2c_write_fifo(i2c); 602 603 /* img_i2c_write_fifo() may modify int_enable */ 604 img_i2c_writel(i2c, SCB_INT_MASK_REG, i2c->int_enable); 605 } 606 607 /* 608 * Indicate that the transaction is complete. This is called from the 609 * ISR to wake up the waiting thread, after which the ISR must not 610 * access any more SCB registers. 611 */ 612 static void img_i2c_complete_transaction(struct img_i2c *i2c, int status) 613 { 614 img_i2c_switch_mode(i2c, MODE_INACTIVE); 615 if (status) { 616 i2c->msg_status = status; 617 img_i2c_transaction_halt(i2c, false); 618 } 619 complete(&i2c->msg_complete); 620 } 621 622 static unsigned int img_i2c_raw_atomic_delay_handler(struct img_i2c *i2c, 623 u32 int_status, u32 line_status) 624 { 625 /* Stay in raw mode for this, so we don't just loop infinitely */ 626 img_i2c_atomic_op(i2c, i2c->at_cur_cmd, i2c->at_cur_data); 627 img_i2c_switch_mode(i2c, MODE_ATOMIC); 628 return 0; 629 } 630 631 static unsigned int img_i2c_raw(struct img_i2c *i2c, u32 int_status, 632 u32 line_status) 633 { 634 if (int_status & INT_TIMING) { 635 if (i2c->raw_timeout == 0) 636 return img_i2c_raw_atomic_delay_handler(i2c, 637 int_status, line_status); 638 --i2c->raw_timeout; 639 } 640 return 0; 641 } 642 643 static unsigned int img_i2c_sequence(struct img_i2c *i2c, u32 int_status) 644 { 645 static const unsigned int continue_bits[] = { 646 [CMD_GEN_START] = LINESTAT_START_BIT_DET, 647 [CMD_GEN_DATA] = LINESTAT_INPUT_HELD_V, 648 [CMD_RET_ACK] = LINESTAT_ACK_DET | LINESTAT_NACK_DET, 649 [CMD_RET_DATA] = LINESTAT_INPUT_HELD_V, 650 [CMD_GEN_STOP] = LINESTAT_STOP_BIT_DET, 651 }; 652 int next_cmd = -1; 653 u8 next_data = 0x00; 654 655 if (int_status & INT_SLAVE_EVENT) 656 i2c->at_slave_event = true; 657 if (int_status & INT_TRANSACTION_DONE) 658 i2c->at_t_done = true; 659 660 if (!i2c->at_slave_event || !i2c->at_t_done) 661 return 0; 662 663 /* wait if no continue bits are set */ 664 if (i2c->at_cur_cmd >= 0 && 665 i2c->at_cur_cmd < ARRAY_SIZE(continue_bits)) { 666 unsigned int cont_bits = continue_bits[i2c->at_cur_cmd]; 667 668 if (cont_bits) { 669 cont_bits |= LINESTAT_ABORT_DET; 670 if (!(i2c->line_status & cont_bits)) 671 return 0; 672 } 673 } 674 675 /* follow the sequence of commands in i2c->seq */ 676 next_cmd = *i2c->seq; 677 /* stop on a nil */ 678 if (!next_cmd) { 679 img_i2c_writel(i2c, SCB_OVERRIDE_REG, 0); 680 return ISR_COMPLETE(0); 681 } 682 /* when generating data, the next byte is the data */ 683 if (next_cmd == CMD_GEN_DATA) { 684 ++i2c->seq; 685 next_data = *i2c->seq; 686 } 687 ++i2c->seq; 688 img_i2c_atomic_op(i2c, next_cmd, next_data); 689 690 return 0; 691 } 692 693 static void img_i2c_reset_start(struct img_i2c *i2c) 694 { 695 /* Initiate the magic dance */ 696 img_i2c_switch_mode(i2c, MODE_SEQUENCE); 697 img_i2c_writel(i2c, SCB_INT_MASK_REG, i2c->int_enable); 698 i2c->seq = img_i2c_reset_seq; 699 i2c->at_slave_event = true; 700 i2c->at_t_done = true; 701 i2c->at_cur_cmd = -1; 702 703 /* img_i2c_reset_seq isn't empty so the following won't fail */ 704 img_i2c_sequence(i2c, 0); 705 } 706 707 static void img_i2c_stop_start(struct img_i2c *i2c) 708 { 709 /* Initiate a stop bit sequence */ 710 img_i2c_switch_mode(i2c, MODE_SEQUENCE); 711 img_i2c_writel(i2c, SCB_INT_MASK_REG, i2c->int_enable); 712 i2c->seq = img_i2c_stop_seq; 713 i2c->at_slave_event = true; 714 i2c->at_t_done = true; 715 i2c->at_cur_cmd = -1; 716 717 /* img_i2c_stop_seq isn't empty so the following won't fail */ 718 img_i2c_sequence(i2c, 0); 719 } 720 721 static unsigned int img_i2c_atomic(struct img_i2c *i2c, 722 u32 int_status, 723 u32 line_status) 724 { 725 int next_cmd = -1; 726 u8 next_data = 0x00; 727 728 if (int_status & INT_SLAVE_EVENT) 729 i2c->at_slave_event = true; 730 if (int_status & INT_TRANSACTION_DONE) 731 i2c->at_t_done = true; 732 733 if (!i2c->at_slave_event || !i2c->at_t_done) 734 goto next_atomic_cmd; 735 if (i2c->line_status & LINESTAT_ABORT_DET) { 736 dev_dbg(i2c->adap.dev.parent, "abort condition detected\n"); 737 next_cmd = CMD_GEN_STOP; 738 i2c->msg_status = -EIO; 739 goto next_atomic_cmd; 740 } 741 742 /* i2c->at_cur_cmd may have completed */ 743 switch (i2c->at_cur_cmd) { 744 case CMD_GEN_START: 745 next_cmd = CMD_GEN_DATA; 746 next_data = (i2c->msg.addr << 1); 747 if (i2c->msg.flags & I2C_M_RD) 748 next_data |= 0x1; 749 break; 750 case CMD_GEN_DATA: 751 if (i2c->line_status & LINESTAT_INPUT_HELD_V) 752 next_cmd = CMD_RET_ACK; 753 break; 754 case CMD_RET_ACK: 755 if (i2c->line_status & LINESTAT_ACK_DET) { 756 if (i2c->msg.len == 0) { 757 next_cmd = CMD_GEN_STOP; 758 } else if (i2c->msg.flags & I2C_M_RD) { 759 next_cmd = CMD_RET_DATA; 760 } else { 761 next_cmd = CMD_GEN_DATA; 762 next_data = *i2c->msg.buf; 763 --i2c->msg.len; 764 ++i2c->msg.buf; 765 } 766 } else if (i2c->line_status & LINESTAT_NACK_DET) { 767 i2c->msg_status = -EIO; 768 next_cmd = CMD_GEN_STOP; 769 } 770 break; 771 case CMD_RET_DATA: 772 if (i2c->line_status & LINESTAT_INPUT_HELD_V) { 773 *i2c->msg.buf = (i2c->line_status & 774 LINESTAT_INPUT_DATA) 775 >> LINESTAT_INPUT_DATA_SHIFT; 776 --i2c->msg.len; 777 ++i2c->msg.buf; 778 if (i2c->msg.len) 779 next_cmd = CMD_GEN_ACK; 780 else 781 next_cmd = CMD_GEN_NACK; 782 } 783 break; 784 case CMD_GEN_ACK: 785 if (i2c->line_status & LINESTAT_ACK_DET) { 786 next_cmd = CMD_RET_DATA; 787 } else { 788 i2c->msg_status = -EIO; 789 next_cmd = CMD_GEN_STOP; 790 } 791 break; 792 case CMD_GEN_NACK: 793 next_cmd = CMD_GEN_STOP; 794 break; 795 case CMD_GEN_STOP: 796 img_i2c_writel(i2c, SCB_OVERRIDE_REG, 0); 797 return ISR_COMPLETE(0); 798 default: 799 dev_err(i2c->adap.dev.parent, "bad atomic command %d\n", 800 i2c->at_cur_cmd); 801 i2c->msg_status = -EIO; 802 next_cmd = CMD_GEN_STOP; 803 break; 804 } 805 806 next_atomic_cmd: 807 if (next_cmd != -1) { 808 /* don't actually stop unless we're the last transaction */ 809 if (next_cmd == CMD_GEN_STOP && !i2c->msg_status && 810 !i2c->last_msg) 811 return ISR_COMPLETE(0); 812 img_i2c_atomic_op(i2c, next_cmd, next_data); 813 } 814 return 0; 815 } 816 817 /* 818 * Timer function to check if something has gone wrong in automatic mode (so we 819 * don't have to handle so many interrupts just to catch an exception). 820 */ 821 static void img_i2c_check_timer(unsigned long arg) 822 { 823 struct img_i2c *i2c = (struct img_i2c *)arg; 824 unsigned long flags; 825 unsigned int line_status; 826 827 spin_lock_irqsave(&i2c->lock, flags); 828 line_status = img_i2c_readl(i2c, SCB_STATUS_REG); 829 830 /* check for an abort condition */ 831 if (line_status & LINESTAT_ABORT_DET) { 832 dev_dbg(i2c->adap.dev.parent, 833 "abort condition detected by check timer\n"); 834 /* enable slave event interrupt mask to trigger irq */ 835 img_i2c_writel(i2c, SCB_INT_MASK_REG, 836 i2c->int_enable | INT_SLAVE_EVENT); 837 } 838 839 spin_unlock_irqrestore(&i2c->lock, flags); 840 } 841 842 static unsigned int img_i2c_auto(struct img_i2c *i2c, 843 unsigned int int_status, 844 unsigned int line_status) 845 { 846 if (int_status & (INT_WRITE_ACK_ERR | INT_ADDR_ACK_ERR)) 847 return ISR_COMPLETE(EIO); 848 849 if (line_status & LINESTAT_ABORT_DET) { 850 dev_dbg(i2c->adap.dev.parent, "abort condition detected\n"); 851 /* empty the read fifo */ 852 if ((i2c->msg.flags & I2C_M_RD) && 853 (int_status & INT_FIFO_FULL_FILLING)) 854 img_i2c_read_fifo(i2c); 855 /* use atomic mode and try to force a stop bit */ 856 i2c->msg_status = -EIO; 857 img_i2c_stop_start(i2c); 858 return 0; 859 } 860 861 /* Enable transaction halt on start bit */ 862 if (!i2c->last_msg && i2c->line_status & LINESTAT_START_BIT_DET) { 863 img_i2c_transaction_halt(i2c, true); 864 /* we're no longer interested in the slave event */ 865 i2c->int_enable &= ~INT_SLAVE_EVENT; 866 } 867 868 mod_timer(&i2c->check_timer, jiffies + msecs_to_jiffies(1)); 869 870 if (i2c->msg.flags & I2C_M_RD) { 871 if (int_status & INT_FIFO_FULL_FILLING) { 872 img_i2c_read_fifo(i2c); 873 if (i2c->msg.len == 0) 874 return ISR_WAITSTOP; 875 } 876 } else { 877 if (int_status & INT_FIFO_EMPTY_EMPTYING) { 878 /* 879 * The write fifo empty indicates that we're in the 880 * last byte so it's safe to start a new write 881 * transaction without losing any bytes from the 882 * previous one. 883 * see 2.3.7 Repeated Start Transactions. 884 */ 885 if ((int_status & INT_FIFO_EMPTY) && 886 i2c->msg.len == 0) 887 return ISR_WAITSTOP; 888 img_i2c_write_fifo(i2c); 889 } 890 } 891 892 return 0; 893 } 894 895 static irqreturn_t img_i2c_isr(int irq, void *dev_id) 896 { 897 struct img_i2c *i2c = (struct img_i2c *)dev_id; 898 u32 int_status, line_status; 899 /* We handle transaction completion AFTER accessing registers */ 900 unsigned int hret; 901 902 /* Read interrupt status register. */ 903 int_status = img_i2c_readl(i2c, SCB_INT_STATUS_REG); 904 /* Clear detected interrupts. */ 905 img_i2c_writel(i2c, SCB_INT_CLEAR_REG, int_status); 906 907 /* 908 * Read line status and clear it until it actually is clear. We have 909 * to be careful not to lose any line status bits that get latched. 910 */ 911 line_status = img_i2c_readl(i2c, SCB_STATUS_REG); 912 if (line_status & LINESTAT_LATCHED) { 913 img_i2c_writel(i2c, SCB_CLEAR_REG, 914 (line_status & LINESTAT_LATCHED) 915 >> LINESTAT_CLEAR_SHIFT); 916 img_i2c_wr_rd_fence(i2c); 917 } 918 919 spin_lock(&i2c->lock); 920 921 /* Keep track of line status bits received */ 922 i2c->line_status &= ~LINESTAT_INPUT_DATA; 923 i2c->line_status |= line_status; 924 925 /* 926 * Certain interrupts indicate that sclk low timeout is not 927 * a problem. If any of these are set, just continue. 928 */ 929 if ((int_status & INT_SCLK_LOW_TIMEOUT) && 930 !(int_status & (INT_SLAVE_EVENT | 931 INT_FIFO_EMPTY | 932 INT_FIFO_FULL))) { 933 dev_crit(i2c->adap.dev.parent, 934 "fatal: clock low timeout occurred %s addr 0x%02x\n", 935 (i2c->msg.flags & I2C_M_RD) ? "reading" : "writing", 936 i2c->msg.addr); 937 hret = ISR_FATAL(EIO); 938 goto out; 939 } 940 941 if (i2c->mode == MODE_ATOMIC) 942 hret = img_i2c_atomic(i2c, int_status, line_status); 943 else if (i2c->mode == MODE_AUTOMATIC) 944 hret = img_i2c_auto(i2c, int_status, line_status); 945 else if (i2c->mode == MODE_SEQUENCE) 946 hret = img_i2c_sequence(i2c, int_status); 947 else if (i2c->mode == MODE_WAITSTOP && (int_status & INT_SLAVE_EVENT) && 948 (line_status & LINESTAT_STOP_BIT_DET)) 949 hret = ISR_COMPLETE(0); 950 else if (i2c->mode == MODE_RAW) 951 hret = img_i2c_raw(i2c, int_status, line_status); 952 else 953 hret = 0; 954 955 /* Clear detected level interrupts. */ 956 img_i2c_writel(i2c, SCB_INT_CLEAR_REG, int_status & INT_LEVEL); 957 958 out: 959 if (hret & ISR_WAITSTOP) { 960 /* 961 * Only wait for stop on last message. 962 * Also we may already have detected the stop bit. 963 */ 964 if (!i2c->last_msg || i2c->line_status & LINESTAT_STOP_BIT_DET) 965 hret = ISR_COMPLETE(0); 966 else 967 img_i2c_switch_mode(i2c, MODE_WAITSTOP); 968 } 969 970 /* now we've finished using regs, handle transaction completion */ 971 if (hret & ISR_COMPLETE_M) { 972 int status = -(hret & ISR_STATUS_M); 973 974 img_i2c_complete_transaction(i2c, status); 975 if (hret & ISR_FATAL_M) 976 img_i2c_switch_mode(i2c, MODE_FATAL); 977 } 978 979 /* Enable interrupts (int_enable may be altered by changing mode) */ 980 img_i2c_writel(i2c, SCB_INT_MASK_REG, i2c->int_enable); 981 982 spin_unlock(&i2c->lock); 983 984 return IRQ_HANDLED; 985 } 986 987 /* Force a bus reset sequence and wait for it to complete */ 988 static int img_i2c_reset_bus(struct img_i2c *i2c) 989 { 990 unsigned long flags; 991 int ret; 992 993 spin_lock_irqsave(&i2c->lock, flags); 994 reinit_completion(&i2c->msg_complete); 995 img_i2c_reset_start(i2c); 996 spin_unlock_irqrestore(&i2c->lock, flags); 997 998 ret = wait_for_completion_timeout(&i2c->msg_complete, IMG_I2C_TIMEOUT); 999 if (ret == 0) 1000 return -ETIMEDOUT; 1001 return 0; 1002 } 1003 1004 static int img_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, 1005 int num) 1006 { 1007 struct img_i2c *i2c = i2c_get_adapdata(adap); 1008 bool atomic = false; 1009 int i, ret; 1010 1011 if (i2c->mode == MODE_SUSPEND) { 1012 WARN(1, "refusing to service transaction in suspended state\n"); 1013 return -EIO; 1014 } 1015 1016 if (i2c->mode == MODE_FATAL) 1017 return -EIO; 1018 1019 for (i = 0; i < num; i++) { 1020 if (likely(msgs[i].len)) 1021 continue; 1022 /* 1023 * 0 byte reads are not possible because the slave could try 1024 * and pull the data line low, preventing a stop bit. 1025 */ 1026 if (unlikely(msgs[i].flags & I2C_M_RD)) 1027 return -EIO; 1028 /* 1029 * 0 byte writes are possible and used for probing, but we 1030 * cannot do them in automatic mode, so use atomic mode 1031 * instead. 1032 */ 1033 atomic = true; 1034 } 1035 1036 ret = clk_prepare_enable(i2c->scb_clk); 1037 if (ret) 1038 return ret; 1039 1040 for (i = 0; i < num; i++) { 1041 struct i2c_msg *msg = &msgs[i]; 1042 unsigned long flags; 1043 1044 spin_lock_irqsave(&i2c->lock, flags); 1045 1046 /* 1047 * Make a copy of the message struct. We mustn't modify the 1048 * original or we'll confuse drivers and i2c-dev. 1049 */ 1050 i2c->msg = *msg; 1051 i2c->msg_status = 0; 1052 1053 /* 1054 * After the last message we must have waited for a stop bit. 1055 * Not waiting can cause problems when the clock is disabled 1056 * before the stop bit is sent, and the linux I2C interface 1057 * requires separate transfers not to joined with repeated 1058 * start. 1059 */ 1060 i2c->last_msg = (i == num - 1); 1061 reinit_completion(&i2c->msg_complete); 1062 1063 if (atomic) 1064 img_i2c_atomic_start(i2c); 1065 else if (msg->flags & I2C_M_RD) 1066 img_i2c_read(i2c); 1067 else 1068 img_i2c_write(i2c); 1069 spin_unlock_irqrestore(&i2c->lock, flags); 1070 1071 ret = wait_for_completion_timeout(&i2c->msg_complete, 1072 IMG_I2C_TIMEOUT); 1073 del_timer_sync(&i2c->check_timer); 1074 1075 if (ret == 0) { 1076 dev_err(adap->dev.parent, "i2c transfer timed out\n"); 1077 i2c->msg_status = -ETIMEDOUT; 1078 break; 1079 } 1080 1081 if (i2c->msg_status) 1082 break; 1083 } 1084 1085 clk_disable_unprepare(i2c->scb_clk); 1086 1087 return i2c->msg_status ? i2c->msg_status : num; 1088 } 1089 1090 static u32 img_i2c_func(struct i2c_adapter *adap) 1091 { 1092 return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL; 1093 } 1094 1095 static const struct i2c_algorithm img_i2c_algo = { 1096 .master_xfer = img_i2c_xfer, 1097 .functionality = img_i2c_func, 1098 }; 1099 1100 static int img_i2c_init(struct img_i2c *i2c) 1101 { 1102 unsigned int clk_khz, bitrate_khz, clk_period, tckh, tckl, tsdh; 1103 unsigned int i, ret, data, prescale, inc, int_bitrate, filt; 1104 struct img_i2c_timings timing; 1105 u32 rev; 1106 1107 ret = clk_prepare_enable(i2c->scb_clk); 1108 if (ret) 1109 return ret; 1110 1111 rev = img_i2c_readl(i2c, SCB_CORE_REV_REG); 1112 if ((rev & 0x00ffffff) < 0x00020200) { 1113 dev_info(i2c->adap.dev.parent, 1114 "Unknown hardware revision (%d.%d.%d.%d)\n", 1115 (rev >> 24) & 0xff, (rev >> 16) & 0xff, 1116 (rev >> 8) & 0xff, rev & 0xff); 1117 clk_disable_unprepare(i2c->scb_clk); 1118 return -EINVAL; 1119 } 1120 1121 if (rev == REL_SOC_IP_SCB_2_2_1) { 1122 i2c->need_wr_rd_fence = true; 1123 dev_info(i2c->adap.dev.parent, "fence quirk enabled"); 1124 } 1125 1126 bitrate_khz = i2c->bitrate / 1000; 1127 clk_khz = clk_get_rate(i2c->scb_clk) / 1000; 1128 1129 /* Determine what mode we're in from the bitrate */ 1130 timing = timings[0]; 1131 for (i = 0; i < ARRAY_SIZE(timings); i++) { 1132 if (i2c->bitrate <= timings[i].max_bitrate) { 1133 timing = timings[i]; 1134 break; 1135 } 1136 } 1137 1138 /* Find the prescale that would give us that inc (approx delay = 0) */ 1139 prescale = SCB_OPT_INC * clk_khz / (256 * 16 * bitrate_khz); 1140 prescale = clamp_t(unsigned int, prescale, 1, 8); 1141 clk_khz /= prescale; 1142 1143 /* Setup the clock increment value */ 1144 inc = (256 * 16 * bitrate_khz) / clk_khz; 1145 1146 /* 1147 * The clock generation logic allows to filter glitches on the bus. 1148 * This filter is able to remove bus glitches shorter than 50ns. 1149 * If the clock enable rate is greater than 20 MHz, no filtering 1150 * is required, so we need to disable it. 1151 * If it's between the 20-40 MHz range, there's no need to divide 1152 * the clock to get a filter. 1153 */ 1154 if (clk_khz < 20000) { 1155 filt = SCB_FILT_DISABLE; 1156 } else if (clk_khz < 40000) { 1157 filt = SCB_FILT_BYPASS; 1158 } else { 1159 /* Calculate filter clock */ 1160 filt = (64000 / ((clk_khz / 1000) * SCB_FILT_GLITCH)); 1161 1162 /* Scale up if needed */ 1163 if (64000 % ((clk_khz / 1000) * SCB_FILT_GLITCH)) 1164 inc++; 1165 1166 if (filt > SCB_FILT_INC_MASK) 1167 filt = SCB_FILT_INC_MASK; 1168 1169 filt = (filt & SCB_FILT_INC_MASK) << SCB_FILT_INC_SHIFT; 1170 } 1171 data = filt | ((inc & SCB_INC_MASK) << SCB_INC_SHIFT) | (prescale - 1); 1172 img_i2c_writel(i2c, SCB_CLK_SET_REG, data); 1173 1174 /* Obtain the clock period of the fx16 clock in ns */ 1175 clk_period = (256 * 1000000) / (clk_khz * inc); 1176 1177 /* Calculate the bitrate in terms of internal clock pulses */ 1178 int_bitrate = 1000000 / (bitrate_khz * clk_period); 1179 if ((1000000 % (bitrate_khz * clk_period)) >= 1180 ((bitrate_khz * clk_period) / 2)) 1181 int_bitrate++; 1182 1183 /* Setup TCKH value */ 1184 tckh = timing.tckh / clk_period; 1185 if (timing.tckh % clk_period) 1186 tckh++; 1187 1188 if (tckh > 0) 1189 data = tckh - 1; 1190 else 1191 data = 0; 1192 1193 img_i2c_writel(i2c, SCB_TIME_TCKH_REG, data); 1194 1195 /* Setup TCKL value */ 1196 tckl = int_bitrate - tckh; 1197 1198 if (tckl > 0) 1199 data = tckl - 1; 1200 else 1201 data = 0; 1202 1203 img_i2c_writel(i2c, SCB_TIME_TCKL_REG, data); 1204 1205 /* Setup TSDH value */ 1206 tsdh = timing.tsdh / clk_period; 1207 if (timing.tsdh % clk_period) 1208 tsdh++; 1209 1210 if (tsdh > 1) 1211 data = tsdh - 1; 1212 else 1213 data = 0x01; 1214 img_i2c_writel(i2c, SCB_TIME_TSDH_REG, data); 1215 1216 /* This value is used later */ 1217 tsdh = data; 1218 1219 /* Setup TPL value */ 1220 data = timing.tpl / clk_period; 1221 if (data > 0) 1222 --data; 1223 img_i2c_writel(i2c, SCB_TIME_TPL_REG, data); 1224 1225 /* Setup TPH value */ 1226 data = timing.tph / clk_period; 1227 if (data > 0) 1228 --data; 1229 img_i2c_writel(i2c, SCB_TIME_TPH_REG, data); 1230 1231 /* Setup TSDL value to TPL + TSDH + 2 */ 1232 img_i2c_writel(i2c, SCB_TIME_TSDL_REG, data + tsdh + 2); 1233 1234 /* Setup TP2S value */ 1235 data = timing.tp2s / clk_period; 1236 if (data > 0) 1237 --data; 1238 img_i2c_writel(i2c, SCB_TIME_TP2S_REG, data); 1239 1240 img_i2c_writel(i2c, SCB_TIME_TBI_REG, TIMEOUT_TBI); 1241 img_i2c_writel(i2c, SCB_TIME_TSL_REG, TIMEOUT_TSL); 1242 img_i2c_writel(i2c, SCB_TIME_TDL_REG, TIMEOUT_TDL); 1243 1244 /* Take module out of soft reset and enable clocks */ 1245 img_i2c_soft_reset(i2c); 1246 1247 /* Disable all interrupts */ 1248 img_i2c_writel(i2c, SCB_INT_MASK_REG, 0); 1249 1250 /* Clear all interrupts */ 1251 img_i2c_writel(i2c, SCB_INT_CLEAR_REG, ~0); 1252 1253 /* Clear the scb_line_status events */ 1254 img_i2c_writel(i2c, SCB_CLEAR_REG, ~0); 1255 1256 /* Enable interrupts */ 1257 img_i2c_writel(i2c, SCB_INT_MASK_REG, i2c->int_enable); 1258 1259 /* Perform a synchronous sequence to reset the bus */ 1260 ret = img_i2c_reset_bus(i2c); 1261 1262 clk_disable_unprepare(i2c->scb_clk); 1263 1264 return ret; 1265 } 1266 1267 static int img_i2c_probe(struct platform_device *pdev) 1268 { 1269 struct device_node *node = pdev->dev.of_node; 1270 struct img_i2c *i2c; 1271 struct resource *res; 1272 int irq, ret; 1273 u32 val; 1274 1275 i2c = devm_kzalloc(&pdev->dev, sizeof(struct img_i2c), GFP_KERNEL); 1276 if (!i2c) 1277 return -ENOMEM; 1278 1279 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 1280 i2c->base = devm_ioremap_resource(&pdev->dev, res); 1281 if (IS_ERR(i2c->base)) 1282 return PTR_ERR(i2c->base); 1283 1284 irq = platform_get_irq(pdev, 0); 1285 if (irq < 0) { 1286 dev_err(&pdev->dev, "can't get irq number\n"); 1287 return irq; 1288 } 1289 1290 i2c->sys_clk = devm_clk_get(&pdev->dev, "sys"); 1291 if (IS_ERR(i2c->sys_clk)) { 1292 dev_err(&pdev->dev, "can't get system clock\n"); 1293 return PTR_ERR(i2c->sys_clk); 1294 } 1295 1296 i2c->scb_clk = devm_clk_get(&pdev->dev, "scb"); 1297 if (IS_ERR(i2c->scb_clk)) { 1298 dev_err(&pdev->dev, "can't get core clock\n"); 1299 return PTR_ERR(i2c->scb_clk); 1300 } 1301 1302 ret = devm_request_irq(&pdev->dev, irq, img_i2c_isr, 0, 1303 pdev->name, i2c); 1304 if (ret) { 1305 dev_err(&pdev->dev, "can't request irq %d\n", irq); 1306 return ret; 1307 } 1308 1309 /* Set up the exception check timer */ 1310 init_timer(&i2c->check_timer); 1311 i2c->check_timer.function = img_i2c_check_timer; 1312 i2c->check_timer.data = (unsigned long)i2c; 1313 1314 i2c->bitrate = timings[0].max_bitrate; 1315 if (!of_property_read_u32(node, "clock-frequency", &val)) 1316 i2c->bitrate = val; 1317 1318 i2c_set_adapdata(&i2c->adap, i2c); 1319 i2c->adap.dev.parent = &pdev->dev; 1320 i2c->adap.dev.of_node = node; 1321 i2c->adap.owner = THIS_MODULE; 1322 i2c->adap.algo = &img_i2c_algo; 1323 i2c->adap.retries = 5; 1324 i2c->adap.nr = pdev->id; 1325 snprintf(i2c->adap.name, sizeof(i2c->adap.name), "IMG SCB I2C"); 1326 1327 img_i2c_switch_mode(i2c, MODE_INACTIVE); 1328 spin_lock_init(&i2c->lock); 1329 init_completion(&i2c->msg_complete); 1330 1331 platform_set_drvdata(pdev, i2c); 1332 1333 ret = clk_prepare_enable(i2c->sys_clk); 1334 if (ret) 1335 return ret; 1336 1337 ret = img_i2c_init(i2c); 1338 if (ret) 1339 goto disable_clk; 1340 1341 ret = i2c_add_numbered_adapter(&i2c->adap); 1342 if (ret < 0) { 1343 dev_err(&pdev->dev, "failed to add adapter\n"); 1344 goto disable_clk; 1345 } 1346 1347 return 0; 1348 1349 disable_clk: 1350 clk_disable_unprepare(i2c->sys_clk); 1351 return ret; 1352 } 1353 1354 static int img_i2c_remove(struct platform_device *dev) 1355 { 1356 struct img_i2c *i2c = platform_get_drvdata(dev); 1357 1358 i2c_del_adapter(&i2c->adap); 1359 clk_disable_unprepare(i2c->sys_clk); 1360 1361 return 0; 1362 } 1363 1364 #ifdef CONFIG_PM_SLEEP 1365 static int img_i2c_suspend(struct device *dev) 1366 { 1367 struct img_i2c *i2c = dev_get_drvdata(dev); 1368 1369 img_i2c_switch_mode(i2c, MODE_SUSPEND); 1370 1371 clk_disable_unprepare(i2c->sys_clk); 1372 1373 return 0; 1374 } 1375 1376 static int img_i2c_resume(struct device *dev) 1377 { 1378 struct img_i2c *i2c = dev_get_drvdata(dev); 1379 int ret; 1380 1381 ret = clk_prepare_enable(i2c->sys_clk); 1382 if (ret) 1383 return ret; 1384 1385 img_i2c_init(i2c); 1386 1387 return 0; 1388 } 1389 #endif /* CONFIG_PM_SLEEP */ 1390 1391 static SIMPLE_DEV_PM_OPS(img_i2c_pm, img_i2c_suspend, img_i2c_resume); 1392 1393 static const struct of_device_id img_scb_i2c_match[] = { 1394 { .compatible = "img,scb-i2c" }, 1395 { } 1396 }; 1397 MODULE_DEVICE_TABLE(of, img_scb_i2c_match); 1398 1399 static struct platform_driver img_scb_i2c_driver = { 1400 .driver = { 1401 .name = "img-i2c-scb", 1402 .of_match_table = img_scb_i2c_match, 1403 .pm = &img_i2c_pm, 1404 }, 1405 .probe = img_i2c_probe, 1406 .remove = img_i2c_remove, 1407 }; 1408 module_platform_driver(img_scb_i2c_driver); 1409 1410 MODULE_AUTHOR("James Hogan <james.hogan@imgtec.com>"); 1411 MODULE_DESCRIPTION("IMG host I2C driver"); 1412 MODULE_LICENSE("GPL v2"); 1413