1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * I2C bus driver for the Cadence I2C controller. 4 * 5 * Copyright (C) 2009 - 2014 Xilinx, Inc. 6 */ 7 8 #include <linux/clk.h> 9 #include <linux/delay.h> 10 #include <linux/i2c.h> 11 #include <linux/interrupt.h> 12 #include <linux/io.h> 13 #include <linux/iopoll.h> 14 #include <linux/module.h> 15 #include <linux/platform_device.h> 16 #include <linux/of.h> 17 #include <linux/pm_runtime.h> 18 #include <linux/pinctrl/consumer.h> 19 #include <linux/reset.h> 20 21 /* Register offsets for the I2C device. */ 22 #define CDNS_I2C_CR_OFFSET 0x00 /* Control Register, RW */ 23 #define CDNS_I2C_SR_OFFSET 0x04 /* Status Register, RO */ 24 #define CDNS_I2C_ADDR_OFFSET 0x08 /* I2C Address Register, RW */ 25 #define CDNS_I2C_DATA_OFFSET 0x0C /* I2C Data Register, RW */ 26 #define CDNS_I2C_ISR_OFFSET 0x10 /* IRQ Status Register, RW */ 27 #define CDNS_I2C_XFER_SIZE_OFFSET 0x14 /* Transfer Size Register, RW */ 28 #define CDNS_I2C_TIME_OUT_OFFSET 0x1C /* Time Out Register, RW */ 29 #define CDNS_I2C_IMR_OFFSET 0x20 /* IRQ Mask Register, RO */ 30 #define CDNS_I2C_IER_OFFSET 0x24 /* IRQ Enable Register, WO */ 31 #define CDNS_I2C_IDR_OFFSET 0x28 /* IRQ Disable Register, WO */ 32 33 /* Control Register Bit mask definitions */ 34 #define CDNS_I2C_CR_HOLD BIT(4) /* Hold Bus bit */ 35 #define CDNS_I2C_CR_ACK_EN BIT(3) 36 #define CDNS_I2C_CR_NEA BIT(2) 37 #define CDNS_I2C_CR_MS BIT(1) 38 /* Read or Write Master transfer 0 = Transmitter, 1 = Receiver */ 39 #define CDNS_I2C_CR_RW BIT(0) 40 /* 1 = Auto init FIFO to zeroes */ 41 #define CDNS_I2C_CR_CLR_FIFO BIT(6) 42 #define CDNS_I2C_CR_DIVA_SHIFT 14 43 #define CDNS_I2C_CR_DIVA_MASK (3 << CDNS_I2C_CR_DIVA_SHIFT) 44 #define CDNS_I2C_CR_DIVB_SHIFT 8 45 #define CDNS_I2C_CR_DIVB_MASK (0x3f << CDNS_I2C_CR_DIVB_SHIFT) 46 47 #define CDNS_I2C_CR_MASTER_EN_MASK (CDNS_I2C_CR_NEA | \ 48 CDNS_I2C_CR_ACK_EN | \ 49 CDNS_I2C_CR_MS) 50 51 #define CDNS_I2C_CR_SLAVE_EN_MASK ~CDNS_I2C_CR_MASTER_EN_MASK 52 53 /* Status Register Bit mask definitions */ 54 #define CDNS_I2C_SR_BA BIT(8) 55 #define CDNS_I2C_SR_TXDV BIT(6) 56 #define CDNS_I2C_SR_RXDV BIT(5) 57 #define CDNS_I2C_SR_RXRW BIT(3) 58 59 /* 60 * I2C Address Register Bit mask definitions 61 * Normal addressing mode uses [6:0] bits. Extended addressing mode uses [9:0] 62 * bits. A write access to this register always initiates a transfer if the I2C 63 * is in master mode. 64 */ 65 #define CDNS_I2C_ADDR_MASK 0x000003FF /* I2C Address Mask */ 66 67 /* 68 * I2C Interrupt Registers Bit mask definitions 69 * All the four interrupt registers (Status/Mask/Enable/Disable) have the same 70 * bit definitions. 71 */ 72 #define CDNS_I2C_IXR_ARB_LOST BIT(9) 73 #define CDNS_I2C_IXR_RX_UNF BIT(7) 74 #define CDNS_I2C_IXR_TX_OVF BIT(6) 75 #define CDNS_I2C_IXR_RX_OVF BIT(5) 76 #define CDNS_I2C_IXR_SLV_RDY BIT(4) 77 #define CDNS_I2C_IXR_TO BIT(3) 78 #define CDNS_I2C_IXR_NACK BIT(2) 79 #define CDNS_I2C_IXR_DATA BIT(1) 80 #define CDNS_I2C_IXR_COMP BIT(0) 81 82 #define CDNS_I2C_IXR_ALL_INTR_MASK (CDNS_I2C_IXR_ARB_LOST | \ 83 CDNS_I2C_IXR_RX_UNF | \ 84 CDNS_I2C_IXR_TX_OVF | \ 85 CDNS_I2C_IXR_RX_OVF | \ 86 CDNS_I2C_IXR_SLV_RDY | \ 87 CDNS_I2C_IXR_TO | \ 88 CDNS_I2C_IXR_NACK | \ 89 CDNS_I2C_IXR_DATA | \ 90 CDNS_I2C_IXR_COMP) 91 92 #define CDNS_I2C_IXR_ERR_INTR_MASK (CDNS_I2C_IXR_ARB_LOST | \ 93 CDNS_I2C_IXR_RX_UNF | \ 94 CDNS_I2C_IXR_TX_OVF | \ 95 CDNS_I2C_IXR_RX_OVF | \ 96 CDNS_I2C_IXR_NACK) 97 98 #define CDNS_I2C_ENABLED_INTR_MASK (CDNS_I2C_IXR_ARB_LOST | \ 99 CDNS_I2C_IXR_RX_UNF | \ 100 CDNS_I2C_IXR_TX_OVF | \ 101 CDNS_I2C_IXR_RX_OVF | \ 102 CDNS_I2C_IXR_NACK | \ 103 CDNS_I2C_IXR_DATA | \ 104 CDNS_I2C_IXR_COMP) 105 106 #define CDNS_I2C_IXR_SLAVE_INTR_MASK (CDNS_I2C_IXR_RX_UNF | \ 107 CDNS_I2C_IXR_TX_OVF | \ 108 CDNS_I2C_IXR_RX_OVF | \ 109 CDNS_I2C_IXR_TO | \ 110 CDNS_I2C_IXR_NACK | \ 111 CDNS_I2C_IXR_DATA | \ 112 CDNS_I2C_IXR_COMP) 113 114 #define CDNS_I2C_TIMEOUT msecs_to_jiffies(1000) 115 /* timeout for pm runtime autosuspend */ 116 #define CNDS_I2C_PM_TIMEOUT 1000 /* ms */ 117 118 #define CDNS_I2C_FIFO_DEPTH_DEFAULT 16 119 #define CDNS_I2C_MAX_TRANSFER_SIZE 255 120 /* Transfer size in multiples of data interrupt depth */ 121 #define CDNS_I2C_TRANSFER_SIZE(max) ((max) - 3) 122 123 #define DRIVER_NAME "cdns-i2c" 124 125 #define CDNS_I2C_DIVA_MAX 4 126 #define CDNS_I2C_DIVB_MAX 64 127 128 #define CDNS_I2C_TIMEOUT_MAX 0xFF 129 130 #define CDNS_I2C_BROKEN_HOLD_BIT BIT(0) 131 #define CDNS_I2C_POLL_US 100000 132 #define CDNS_I2C_TIMEOUT_US 500000 133 134 #define cdns_i2c_readreg(offset) readl_relaxed(id->membase + offset) 135 #define cdns_i2c_writereg(val, offset) writel_relaxed(val, id->membase + offset) 136 137 #if IS_ENABLED(CONFIG_I2C_SLAVE) 138 /** 139 * enum cdns_i2c_mode - I2C Controller current operating mode 140 * 141 * @CDNS_I2C_MODE_SLAVE: I2C controller operating in slave mode 142 * @CDNS_I2C_MODE_MASTER: I2C Controller operating in master mode 143 */ 144 enum cdns_i2c_mode { 145 CDNS_I2C_MODE_SLAVE, 146 CDNS_I2C_MODE_MASTER, 147 }; 148 149 /** 150 * enum cdns_i2c_slave_state - Slave state when I2C is operating in slave mode 151 * 152 * @CDNS_I2C_SLAVE_STATE_IDLE: I2C slave idle 153 * @CDNS_I2C_SLAVE_STATE_SEND: I2C slave sending data to master 154 * @CDNS_I2C_SLAVE_STATE_RECV: I2C slave receiving data from master 155 */ 156 enum cdns_i2c_slave_state { 157 CDNS_I2C_SLAVE_STATE_IDLE, 158 CDNS_I2C_SLAVE_STATE_SEND, 159 CDNS_I2C_SLAVE_STATE_RECV, 160 }; 161 #endif 162 163 /** 164 * struct cdns_i2c - I2C device private data structure 165 * 166 * @dev: Pointer to device structure 167 * @membase: Base address of the I2C device 168 * @adap: I2C adapter instance 169 * @p_msg: Message pointer 170 * @err_status: Error status in Interrupt Status Register 171 * @xfer_done: Transfer complete status 172 * @p_send_buf: Pointer to transmit buffer 173 * @p_recv_buf: Pointer to receive buffer 174 * @send_count: Number of bytes still expected to send 175 * @recv_count: Number of bytes still expected to receive 176 * @curr_recv_count: Number of bytes to be received in current transfer 177 * @input_clk: Input clock to I2C controller 178 * @i2c_clk: Maximum I2C clock speed 179 * @bus_hold_flag: Flag used in repeated start for clearing HOLD bit 180 * @clk: Pointer to struct clk 181 * @clk_rate_change_nb: Notifier block for clock rate changes 182 * @reset: Reset control for the device 183 * @quirks: flag for broken hold bit usage in r1p10 184 * @ctrl_reg: Cached value of the control register. 185 * @rinfo: I2C GPIO recovery information 186 * @ctrl_reg_diva_divb: value of fields DIV_A and DIV_B from CR register 187 * @slave: Registered slave instance. 188 * @dev_mode: I2C operating role(master/slave). 189 * @slave_state: I2C Slave state(idle/read/write). 190 * @fifo_depth: The depth of the transfer FIFO 191 * @transfer_size: The maximum number of bytes in one transfer 192 */ 193 struct cdns_i2c { 194 struct device *dev; 195 void __iomem *membase; 196 struct i2c_adapter adap; 197 struct i2c_msg *p_msg; 198 int err_status; 199 struct completion xfer_done; 200 unsigned char *p_send_buf; 201 unsigned char *p_recv_buf; 202 unsigned int send_count; 203 unsigned int recv_count; 204 unsigned int curr_recv_count; 205 unsigned long input_clk; 206 unsigned int i2c_clk; 207 unsigned int bus_hold_flag; 208 struct clk *clk; 209 struct notifier_block clk_rate_change_nb; 210 struct reset_control *reset; 211 u32 quirks; 212 u32 ctrl_reg; 213 struct i2c_bus_recovery_info rinfo; 214 #if IS_ENABLED(CONFIG_I2C_SLAVE) 215 u16 ctrl_reg_diva_divb; 216 struct i2c_client *slave; 217 enum cdns_i2c_mode dev_mode; 218 enum cdns_i2c_slave_state slave_state; 219 #endif 220 u32 fifo_depth; 221 unsigned int transfer_size; 222 }; 223 224 struct cdns_platform_data { 225 u32 quirks; 226 }; 227 228 #define to_cdns_i2c(_nb) container_of(_nb, struct cdns_i2c, \ 229 clk_rate_change_nb) 230 231 /** 232 * cdns_i2c_clear_bus_hold - Clear bus hold bit 233 * @id: Pointer to driver data struct 234 * 235 * Helper to clear the controller's bus hold bit. 236 */ 237 static void cdns_i2c_clear_bus_hold(struct cdns_i2c *id) 238 { 239 u32 reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET); 240 if (reg & CDNS_I2C_CR_HOLD) 241 cdns_i2c_writereg(reg & ~CDNS_I2C_CR_HOLD, CDNS_I2C_CR_OFFSET); 242 } 243 244 static inline bool cdns_is_holdquirk(struct cdns_i2c *id, bool hold_wrkaround) 245 { 246 return (hold_wrkaround && 247 (id->curr_recv_count == id->fifo_depth + 1)); 248 } 249 250 #if IS_ENABLED(CONFIG_I2C_SLAVE) 251 static void cdns_i2c_set_mode(enum cdns_i2c_mode mode, struct cdns_i2c *id) 252 { 253 /* Disable all interrupts */ 254 cdns_i2c_writereg(CDNS_I2C_IXR_ALL_INTR_MASK, CDNS_I2C_IDR_OFFSET); 255 256 /* Clear FIFO and transfer size */ 257 cdns_i2c_writereg(CDNS_I2C_CR_CLR_FIFO, CDNS_I2C_CR_OFFSET); 258 259 /* Update device mode and state */ 260 id->dev_mode = mode; 261 id->slave_state = CDNS_I2C_SLAVE_STATE_IDLE; 262 263 switch (mode) { 264 case CDNS_I2C_MODE_MASTER: 265 /* Enable i2c master */ 266 cdns_i2c_writereg(id->ctrl_reg_diva_divb | 267 CDNS_I2C_CR_MASTER_EN_MASK, 268 CDNS_I2C_CR_OFFSET); 269 /* 270 * This delay is needed to give the IP some time to switch to 271 * the master mode. With lower values(like 110 us) i2cdetect 272 * will not detect any slave and without this delay, the IP will 273 * trigger a timeout interrupt. 274 */ 275 usleep_range(115, 125); 276 break; 277 case CDNS_I2C_MODE_SLAVE: 278 /* Enable i2c slave */ 279 cdns_i2c_writereg(id->ctrl_reg_diva_divb & 280 CDNS_I2C_CR_SLAVE_EN_MASK, 281 CDNS_I2C_CR_OFFSET); 282 283 /* Setting slave address */ 284 cdns_i2c_writereg(id->slave->addr & CDNS_I2C_ADDR_MASK, 285 CDNS_I2C_ADDR_OFFSET); 286 287 /* Enable slave send/receive interrupts */ 288 cdns_i2c_writereg(CDNS_I2C_IXR_SLAVE_INTR_MASK, 289 CDNS_I2C_IER_OFFSET); 290 break; 291 } 292 } 293 294 static void cdns_i2c_slave_rcv_data(struct cdns_i2c *id) 295 { 296 u8 bytes; 297 unsigned char data; 298 299 /* Prepare backend for data reception */ 300 if (id->slave_state == CDNS_I2C_SLAVE_STATE_IDLE) { 301 id->slave_state = CDNS_I2C_SLAVE_STATE_RECV; 302 i2c_slave_event(id->slave, I2C_SLAVE_WRITE_REQUESTED, NULL); 303 } 304 305 /* Fetch number of bytes to receive */ 306 bytes = cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET); 307 308 /* Read data and send to backend */ 309 while (bytes--) { 310 data = cdns_i2c_readreg(CDNS_I2C_DATA_OFFSET); 311 i2c_slave_event(id->slave, I2C_SLAVE_WRITE_RECEIVED, &data); 312 } 313 } 314 315 static void cdns_i2c_slave_send_data(struct cdns_i2c *id) 316 { 317 u8 data; 318 319 /* Prepare backend for data transmission */ 320 if (id->slave_state == CDNS_I2C_SLAVE_STATE_IDLE) { 321 id->slave_state = CDNS_I2C_SLAVE_STATE_SEND; 322 i2c_slave_event(id->slave, I2C_SLAVE_READ_REQUESTED, &data); 323 } else { 324 i2c_slave_event(id->slave, I2C_SLAVE_READ_PROCESSED, &data); 325 } 326 327 /* Send data over bus */ 328 cdns_i2c_writereg(data, CDNS_I2C_DATA_OFFSET); 329 } 330 331 /** 332 * cdns_i2c_slave_isr - Interrupt handler for the I2C device in slave role 333 * @ptr: Pointer to I2C device private data 334 * 335 * This function handles the data interrupt and transfer complete interrupt of 336 * the I2C device in slave role. 337 * 338 * Return: IRQ_HANDLED always 339 */ 340 static irqreturn_t cdns_i2c_slave_isr(void *ptr) 341 { 342 struct cdns_i2c *id = ptr; 343 unsigned int isr_status, i2c_status; 344 345 /* Fetch the interrupt status */ 346 isr_status = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET); 347 cdns_i2c_writereg(isr_status, CDNS_I2C_ISR_OFFSET); 348 349 /* Ignore masked interrupts */ 350 isr_status &= ~cdns_i2c_readreg(CDNS_I2C_IMR_OFFSET); 351 352 /* Fetch transfer mode (send/receive) */ 353 i2c_status = cdns_i2c_readreg(CDNS_I2C_SR_OFFSET); 354 355 /* Handle data send/receive */ 356 if (i2c_status & CDNS_I2C_SR_RXRW) { 357 /* Send data to master */ 358 if (isr_status & CDNS_I2C_IXR_DATA) 359 cdns_i2c_slave_send_data(id); 360 361 if (isr_status & CDNS_I2C_IXR_COMP) { 362 id->slave_state = CDNS_I2C_SLAVE_STATE_IDLE; 363 i2c_slave_event(id->slave, I2C_SLAVE_STOP, NULL); 364 } 365 } else { 366 /* Receive data from master */ 367 if (isr_status & CDNS_I2C_IXR_DATA) 368 cdns_i2c_slave_rcv_data(id); 369 370 if (isr_status & CDNS_I2C_IXR_COMP) { 371 cdns_i2c_slave_rcv_data(id); 372 id->slave_state = CDNS_I2C_SLAVE_STATE_IDLE; 373 i2c_slave_event(id->slave, I2C_SLAVE_STOP, NULL); 374 } 375 } 376 377 /* Master indicated xfer stop or fifo underflow/overflow */ 378 if (isr_status & (CDNS_I2C_IXR_NACK | CDNS_I2C_IXR_RX_OVF | 379 CDNS_I2C_IXR_RX_UNF | CDNS_I2C_IXR_TX_OVF)) { 380 id->slave_state = CDNS_I2C_SLAVE_STATE_IDLE; 381 i2c_slave_event(id->slave, I2C_SLAVE_STOP, NULL); 382 cdns_i2c_writereg(CDNS_I2C_CR_CLR_FIFO, CDNS_I2C_CR_OFFSET); 383 } 384 385 return IRQ_HANDLED; 386 } 387 #endif 388 389 /** 390 * cdns_i2c_master_isr - Interrupt handler for the I2C device in master role 391 * @ptr: Pointer to I2C device private data 392 * 393 * This function handles the data interrupt, transfer complete interrupt and 394 * the error interrupts of the I2C device in master role. 395 * 396 * Return: IRQ_HANDLED always 397 */ 398 static irqreturn_t cdns_i2c_master_isr(void *ptr) 399 { 400 unsigned int isr_status, avail_bytes; 401 unsigned int bytes_to_send; 402 bool updatetx; 403 struct cdns_i2c *id = ptr; 404 /* Signal completion only after everything is updated */ 405 int done_flag = 0; 406 irqreturn_t status = IRQ_NONE; 407 408 isr_status = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET); 409 cdns_i2c_writereg(isr_status, CDNS_I2C_ISR_OFFSET); 410 id->err_status = 0; 411 412 /* Handling nack and arbitration lost interrupt */ 413 if (isr_status & (CDNS_I2C_IXR_NACK | CDNS_I2C_IXR_ARB_LOST)) { 414 done_flag = 1; 415 status = IRQ_HANDLED; 416 } 417 418 /* 419 * Check if transfer size register needs to be updated again for a 420 * large data receive operation. 421 */ 422 updatetx = id->recv_count > id->curr_recv_count; 423 424 /* When receiving, handle data interrupt and completion interrupt */ 425 if (id->p_recv_buf && 426 ((isr_status & CDNS_I2C_IXR_COMP) || 427 (isr_status & CDNS_I2C_IXR_DATA))) { 428 /* Read data if receive data valid is set */ 429 while (cdns_i2c_readreg(CDNS_I2C_SR_OFFSET) & 430 CDNS_I2C_SR_RXDV) { 431 if (id->recv_count > 0) { 432 *(id->p_recv_buf)++ = 433 cdns_i2c_readreg(CDNS_I2C_DATA_OFFSET); 434 id->recv_count--; 435 id->curr_recv_count--; 436 437 /* 438 * Clear hold bit that was set for FIFO control 439 * if RX data left is less than or equal to 440 * FIFO DEPTH unless repeated start is selected 441 */ 442 if (id->recv_count <= id->fifo_depth && 443 !id->bus_hold_flag) 444 cdns_i2c_clear_bus_hold(id); 445 446 } else { 447 dev_err(id->adap.dev.parent, 448 "xfer_size reg rollover. xfer aborted!\n"); 449 id->err_status |= CDNS_I2C_IXR_TO; 450 break; 451 } 452 453 if (cdns_is_holdquirk(id, updatetx)) 454 break; 455 } 456 457 /* 458 * The controller sends NACK to the slave when transfer size 459 * register reaches zero without considering the HOLD bit. 460 * This workaround is implemented for large data transfers to 461 * maintain transfer size non-zero while performing a large 462 * receive operation. 463 */ 464 if (cdns_is_holdquirk(id, updatetx)) { 465 /* wait while fifo is full */ 466 while (cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET) != 467 (id->curr_recv_count - id->fifo_depth)) 468 ; 469 470 /* 471 * Check number of bytes to be received against maximum 472 * transfer size and update register accordingly. 473 */ 474 if (((int)(id->recv_count) - id->fifo_depth) > 475 id->transfer_size) { 476 cdns_i2c_writereg(id->transfer_size, 477 CDNS_I2C_XFER_SIZE_OFFSET); 478 id->curr_recv_count = id->transfer_size + 479 id->fifo_depth; 480 } else { 481 cdns_i2c_writereg(id->recv_count - 482 id->fifo_depth, 483 CDNS_I2C_XFER_SIZE_OFFSET); 484 id->curr_recv_count = id->recv_count; 485 } 486 } 487 488 /* Clear hold (if not repeated start) and signal completion */ 489 if ((isr_status & CDNS_I2C_IXR_COMP) && !id->recv_count) { 490 if (!id->bus_hold_flag) 491 cdns_i2c_clear_bus_hold(id); 492 done_flag = 1; 493 } 494 495 status = IRQ_HANDLED; 496 } 497 498 /* When sending, handle transfer complete interrupt */ 499 if ((isr_status & CDNS_I2C_IXR_COMP) && !id->p_recv_buf) { 500 /* 501 * If there is more data to be sent, calculate the 502 * space available in FIFO and fill with that many bytes. 503 */ 504 if (id->send_count) { 505 avail_bytes = id->fifo_depth - 506 cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET); 507 if (id->send_count > avail_bytes) 508 bytes_to_send = avail_bytes; 509 else 510 bytes_to_send = id->send_count; 511 512 while (bytes_to_send--) { 513 cdns_i2c_writereg( 514 (*(id->p_send_buf)++), 515 CDNS_I2C_DATA_OFFSET); 516 id->send_count--; 517 } 518 } else { 519 /* 520 * Signal the completion of transaction and 521 * clear the hold bus bit if there are no 522 * further messages to be processed. 523 */ 524 done_flag = 1; 525 } 526 if (!id->send_count && !id->bus_hold_flag) 527 cdns_i2c_clear_bus_hold(id); 528 529 status = IRQ_HANDLED; 530 } 531 532 /* Update the status for errors */ 533 id->err_status |= isr_status & CDNS_I2C_IXR_ERR_INTR_MASK; 534 if (id->err_status) 535 status = IRQ_HANDLED; 536 537 if (done_flag) 538 complete(&id->xfer_done); 539 540 return status; 541 } 542 543 /** 544 * cdns_i2c_isr - Interrupt handler for the I2C device 545 * @irq: irq number for the I2C device 546 * @ptr: void pointer to cdns_i2c structure 547 * 548 * This function passes the control to slave/master based on current role of 549 * i2c controller. 550 * 551 * Return: IRQ_HANDLED always 552 */ 553 static irqreturn_t cdns_i2c_isr(int irq, void *ptr) 554 { 555 #if IS_ENABLED(CONFIG_I2C_SLAVE) 556 struct cdns_i2c *id = ptr; 557 558 if (id->dev_mode == CDNS_I2C_MODE_SLAVE) 559 return cdns_i2c_slave_isr(ptr); 560 #endif 561 return cdns_i2c_master_isr(ptr); 562 } 563 564 /** 565 * cdns_i2c_mrecv - Prepare and start a master receive operation 566 * @id: pointer to the i2c device structure 567 */ 568 static void cdns_i2c_mrecv(struct cdns_i2c *id) 569 { 570 unsigned int ctrl_reg; 571 unsigned int isr_status; 572 unsigned long flags; 573 bool hold_clear = false; 574 bool irq_save = false; 575 576 u32 addr; 577 578 id->p_recv_buf = id->p_msg->buf; 579 id->recv_count = id->p_msg->len; 580 581 /* Put the controller in master receive mode and clear the FIFO */ 582 ctrl_reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET); 583 ctrl_reg |= CDNS_I2C_CR_RW | CDNS_I2C_CR_CLR_FIFO; 584 585 /* 586 * Receive up to I2C_SMBUS_BLOCK_MAX data bytes, plus one message length 587 * byte, plus one checksum byte if PEC is enabled. p_msg->len will be 2 if 588 * PEC is enabled, otherwise 1. 589 */ 590 if (id->p_msg->flags & I2C_M_RECV_LEN) 591 id->recv_count = I2C_SMBUS_BLOCK_MAX + id->p_msg->len; 592 593 id->curr_recv_count = id->recv_count; 594 595 /* 596 * Check for the message size against FIFO depth and set the 597 * 'hold bus' bit if it is greater than FIFO depth. 598 */ 599 if (id->recv_count > id->fifo_depth) 600 ctrl_reg |= CDNS_I2C_CR_HOLD; 601 602 cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET); 603 604 /* Clear the interrupts in interrupt status register */ 605 isr_status = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET); 606 cdns_i2c_writereg(isr_status, CDNS_I2C_ISR_OFFSET); 607 608 /* 609 * The no. of bytes to receive is checked against the limit of 610 * max transfer size. Set transfer size register with no of bytes 611 * receive if it is less than transfer size and transfer size if 612 * it is more. Enable the interrupts. 613 */ 614 if (id->recv_count > id->transfer_size) { 615 cdns_i2c_writereg(id->transfer_size, 616 CDNS_I2C_XFER_SIZE_OFFSET); 617 id->curr_recv_count = id->transfer_size; 618 } else { 619 cdns_i2c_writereg(id->recv_count, CDNS_I2C_XFER_SIZE_OFFSET); 620 } 621 622 /* Determine hold_clear based on number of bytes to receive and hold flag */ 623 if (!id->bus_hold_flag && id->recv_count <= id->fifo_depth) { 624 if (ctrl_reg & CDNS_I2C_CR_HOLD) { 625 hold_clear = true; 626 if (id->quirks & CDNS_I2C_BROKEN_HOLD_BIT) 627 irq_save = true; 628 } 629 } 630 631 addr = id->p_msg->addr; 632 addr &= CDNS_I2C_ADDR_MASK; 633 634 if (hold_clear) { 635 ctrl_reg &= ~CDNS_I2C_CR_HOLD; 636 /* 637 * In case of Xilinx Zynq SOC, clear the HOLD bit before transfer size 638 * register reaches '0'. This is an IP bug which causes transfer size 639 * register overflow to 0xFF. To satisfy this timing requirement, 640 * disable the interrupts on current processor core between register 641 * writes to slave address register and control register. 642 */ 643 if (irq_save) 644 local_irq_save(flags); 645 646 cdns_i2c_writereg(addr, CDNS_I2C_ADDR_OFFSET); 647 cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET); 648 /* Read it back to avoid bufferring and make sure write happens */ 649 cdns_i2c_readreg(CDNS_I2C_CR_OFFSET); 650 651 if (irq_save) 652 local_irq_restore(flags); 653 } else { 654 cdns_i2c_writereg(addr, CDNS_I2C_ADDR_OFFSET); 655 } 656 657 cdns_i2c_writereg(CDNS_I2C_ENABLED_INTR_MASK, CDNS_I2C_IER_OFFSET); 658 } 659 660 /** 661 * cdns_i2c_msend - Prepare and start a master send operation 662 * @id: pointer to the i2c device 663 */ 664 static void cdns_i2c_msend(struct cdns_i2c *id) 665 { 666 unsigned int avail_bytes; 667 unsigned int bytes_to_send; 668 unsigned int ctrl_reg; 669 unsigned int isr_status; 670 671 id->p_recv_buf = NULL; 672 id->p_send_buf = id->p_msg->buf; 673 id->send_count = id->p_msg->len; 674 675 /* Set the controller in Master transmit mode and clear the FIFO. */ 676 ctrl_reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET); 677 ctrl_reg &= ~CDNS_I2C_CR_RW; 678 ctrl_reg |= CDNS_I2C_CR_CLR_FIFO; 679 680 /* 681 * Check for the message size against FIFO depth and set the 682 * 'hold bus' bit if it is greater than FIFO depth. 683 */ 684 if (id->send_count > id->fifo_depth) 685 ctrl_reg |= CDNS_I2C_CR_HOLD; 686 cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET); 687 688 /* Clear the interrupts in interrupt status register. */ 689 isr_status = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET); 690 cdns_i2c_writereg(isr_status, CDNS_I2C_ISR_OFFSET); 691 692 /* 693 * Calculate the space available in FIFO. Check the message length 694 * against the space available, and fill the FIFO accordingly. 695 * Enable the interrupts. 696 */ 697 avail_bytes = id->fifo_depth - 698 cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET); 699 700 if (id->send_count > avail_bytes) 701 bytes_to_send = avail_bytes; 702 else 703 bytes_to_send = id->send_count; 704 705 while (bytes_to_send--) { 706 cdns_i2c_writereg((*(id->p_send_buf)++), CDNS_I2C_DATA_OFFSET); 707 id->send_count--; 708 } 709 710 /* 711 * Clear the bus hold flag if there is no more data 712 * and if it is the last message. 713 */ 714 if (!id->bus_hold_flag && !id->send_count) 715 cdns_i2c_clear_bus_hold(id); 716 /* Set the slave address in address register - triggers operation. */ 717 cdns_i2c_writereg(id->p_msg->addr & CDNS_I2C_ADDR_MASK, 718 CDNS_I2C_ADDR_OFFSET); 719 720 cdns_i2c_writereg(CDNS_I2C_ENABLED_INTR_MASK, CDNS_I2C_IER_OFFSET); 721 } 722 723 /** 724 * cdns_i2c_master_reset - Reset the interface 725 * @adap: pointer to the i2c adapter driver instance 726 * 727 * This function cleanup the fifos, clear the hold bit and status 728 * and disable the interrupts. 729 */ 730 static void cdns_i2c_master_reset(struct i2c_adapter *adap) 731 { 732 struct cdns_i2c *id = adap->algo_data; 733 u32 regval; 734 735 /* Disable the interrupts */ 736 cdns_i2c_writereg(CDNS_I2C_IXR_ALL_INTR_MASK, CDNS_I2C_IDR_OFFSET); 737 /* Clear the hold bit and fifos */ 738 regval = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET); 739 regval &= ~CDNS_I2C_CR_HOLD; 740 regval |= CDNS_I2C_CR_CLR_FIFO; 741 cdns_i2c_writereg(regval, CDNS_I2C_CR_OFFSET); 742 /* Update the transfercount register to zero */ 743 cdns_i2c_writereg(0, CDNS_I2C_XFER_SIZE_OFFSET); 744 /* Clear the interrupt status register */ 745 regval = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET); 746 cdns_i2c_writereg(regval, CDNS_I2C_ISR_OFFSET); 747 /* Clear the status register */ 748 regval = cdns_i2c_readreg(CDNS_I2C_SR_OFFSET); 749 cdns_i2c_writereg(regval, CDNS_I2C_SR_OFFSET); 750 } 751 752 static int cdns_i2c_process_msg(struct cdns_i2c *id, struct i2c_msg *msg, 753 struct i2c_adapter *adap) 754 { 755 unsigned long time_left, msg_timeout; 756 u32 reg; 757 758 id->p_msg = msg; 759 id->err_status = 0; 760 reinit_completion(&id->xfer_done); 761 762 /* Check for the TEN Bit mode on each msg */ 763 reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET); 764 if (msg->flags & I2C_M_TEN) { 765 if (reg & CDNS_I2C_CR_NEA) 766 cdns_i2c_writereg(reg & ~CDNS_I2C_CR_NEA, 767 CDNS_I2C_CR_OFFSET); 768 } else { 769 if (!(reg & CDNS_I2C_CR_NEA)) 770 cdns_i2c_writereg(reg | CDNS_I2C_CR_NEA, 771 CDNS_I2C_CR_OFFSET); 772 } 773 774 /* Check for the R/W flag on each msg */ 775 if (msg->flags & I2C_M_RD) 776 cdns_i2c_mrecv(id); 777 else 778 cdns_i2c_msend(id); 779 780 /* Minimal time to execute this message */ 781 msg_timeout = msecs_to_jiffies((1000 * msg->len * BITS_PER_BYTE) / id->i2c_clk); 782 /* Plus some wiggle room */ 783 msg_timeout += msecs_to_jiffies(500); 784 785 if (msg_timeout < adap->timeout) 786 msg_timeout = adap->timeout; 787 788 /* Wait for the signal of completion */ 789 time_left = wait_for_completion_timeout(&id->xfer_done, msg_timeout); 790 if (time_left == 0) { 791 cdns_i2c_master_reset(adap); 792 dev_err(id->adap.dev.parent, 793 "timeout waiting on completion\n"); 794 return -ETIMEDOUT; 795 } 796 797 cdns_i2c_writereg(CDNS_I2C_IXR_ALL_INTR_MASK, 798 CDNS_I2C_IDR_OFFSET); 799 800 /* If it is bus arbitration error, try again */ 801 if (id->err_status & CDNS_I2C_IXR_ARB_LOST) 802 return -EAGAIN; 803 804 if (msg->flags & I2C_M_RECV_LEN) 805 msg->len += min_t(unsigned int, msg->buf[0], I2C_SMBUS_BLOCK_MAX); 806 807 return 0; 808 } 809 810 /** 811 * cdns_i2c_master_xfer - The main i2c transfer function 812 * @adap: pointer to the i2c adapter driver instance 813 * @msgs: pointer to the i2c message structure 814 * @num: the number of messages to transfer 815 * 816 * Initiates the send/recv activity based on the transfer message received. 817 * 818 * Return: number of msgs processed on success, negative error otherwise 819 */ 820 static int cdns_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, 821 int num) 822 { 823 int ret, count; 824 u32 reg; 825 struct cdns_i2c *id = adap->algo_data; 826 bool hold_quirk; 827 #if IS_ENABLED(CONFIG_I2C_SLAVE) 828 bool change_role = false; 829 #endif 830 831 ret = pm_runtime_resume_and_get(id->dev); 832 if (ret < 0) 833 return ret; 834 835 #if IS_ENABLED(CONFIG_I2C_SLAVE) 836 /* Check i2c operating mode and switch if possible */ 837 if (id->dev_mode == CDNS_I2C_MODE_SLAVE) { 838 if (id->slave_state != CDNS_I2C_SLAVE_STATE_IDLE) { 839 ret = -EAGAIN; 840 goto out; 841 } 842 843 /* Set mode to master */ 844 cdns_i2c_set_mode(CDNS_I2C_MODE_MASTER, id); 845 846 /* Mark flag to change role once xfer is completed */ 847 change_role = true; 848 } 849 #endif 850 851 /* Check if the bus is free */ 852 853 ret = readl_relaxed_poll_timeout(id->membase + CDNS_I2C_SR_OFFSET, 854 reg, 855 !(reg & CDNS_I2C_SR_BA), 856 CDNS_I2C_POLL_US, CDNS_I2C_TIMEOUT_US); 857 if (ret) { 858 ret = -EAGAIN; 859 if (id->adap.bus_recovery_info) 860 i2c_recover_bus(adap); 861 goto out; 862 } 863 864 hold_quirk = !!(id->quirks & CDNS_I2C_BROKEN_HOLD_BIT); 865 /* 866 * Set the flag to one when multiple messages are to be 867 * processed with a repeated start. 868 */ 869 if (num > 1) { 870 /* 871 * This controller does not give completion interrupt after a 872 * master receive message if HOLD bit is set (repeated start), 873 * resulting in SW timeout. Hence, if a receive message is 874 * followed by any other message, an error is returned 875 * indicating that this sequence is not supported. 876 */ 877 for (count = 0; (count < num - 1 && hold_quirk); count++) { 878 if (msgs[count].flags & I2C_M_RD) { 879 dev_warn(adap->dev.parent, 880 "Can't do repeated start after a receive message\n"); 881 ret = -EOPNOTSUPP; 882 goto out; 883 } 884 } 885 id->bus_hold_flag = 1; 886 reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET); 887 reg |= CDNS_I2C_CR_HOLD; 888 cdns_i2c_writereg(reg, CDNS_I2C_CR_OFFSET); 889 } else { 890 id->bus_hold_flag = 0; 891 } 892 893 /* Process the msg one by one */ 894 for (count = 0; count < num; count++, msgs++) { 895 if (count == (num - 1)) 896 id->bus_hold_flag = 0; 897 898 ret = cdns_i2c_process_msg(id, msgs, adap); 899 if (ret) 900 goto out; 901 902 /* Report the other error interrupts to application */ 903 if (id->err_status) { 904 cdns_i2c_master_reset(adap); 905 906 if (id->err_status & CDNS_I2C_IXR_NACK) { 907 ret = -ENXIO; 908 goto out; 909 } 910 ret = -EIO; 911 goto out; 912 } 913 } 914 915 ret = num; 916 917 out: 918 919 #if IS_ENABLED(CONFIG_I2C_SLAVE) 920 /* Switch i2c mode to slave */ 921 if (change_role) 922 cdns_i2c_set_mode(CDNS_I2C_MODE_SLAVE, id); 923 #endif 924 925 pm_runtime_mark_last_busy(id->dev); 926 pm_runtime_put_autosuspend(id->dev); 927 return ret; 928 } 929 930 /** 931 * cdns_i2c_func - Returns the supported features of the I2C driver 932 * @adap: pointer to the i2c adapter structure 933 * 934 * Return: 32 bit value, each bit corresponding to a feature 935 */ 936 static u32 cdns_i2c_func(struct i2c_adapter *adap) 937 { 938 u32 func = I2C_FUNC_I2C | I2C_FUNC_10BIT_ADDR | 939 (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK) | 940 I2C_FUNC_SMBUS_BLOCK_DATA; 941 942 #if IS_ENABLED(CONFIG_I2C_SLAVE) 943 func |= I2C_FUNC_SLAVE; 944 #endif 945 946 return func; 947 } 948 949 #if IS_ENABLED(CONFIG_I2C_SLAVE) 950 static int cdns_reg_slave(struct i2c_client *slave) 951 { 952 int ret; 953 struct cdns_i2c *id = container_of(slave->adapter, struct cdns_i2c, 954 adap); 955 956 if (id->slave) 957 return -EBUSY; 958 959 if (slave->flags & I2C_CLIENT_TEN) 960 return -EAFNOSUPPORT; 961 962 ret = pm_runtime_resume_and_get(id->dev); 963 if (ret < 0) 964 return ret; 965 966 /* Store slave information */ 967 id->slave = slave; 968 969 /* Enable I2C slave */ 970 cdns_i2c_set_mode(CDNS_I2C_MODE_SLAVE, id); 971 972 return 0; 973 } 974 975 static int cdns_unreg_slave(struct i2c_client *slave) 976 { 977 struct cdns_i2c *id = container_of(slave->adapter, struct cdns_i2c, 978 adap); 979 980 pm_runtime_put(id->dev); 981 982 /* Remove slave information */ 983 id->slave = NULL; 984 985 /* Enable I2C master */ 986 cdns_i2c_set_mode(CDNS_I2C_MODE_MASTER, id); 987 988 return 0; 989 } 990 #endif 991 992 static const struct i2c_algorithm cdns_i2c_algo = { 993 .master_xfer = cdns_i2c_master_xfer, 994 .functionality = cdns_i2c_func, 995 #if IS_ENABLED(CONFIG_I2C_SLAVE) 996 .reg_slave = cdns_reg_slave, 997 .unreg_slave = cdns_unreg_slave, 998 #endif 999 }; 1000 1001 /** 1002 * cdns_i2c_calc_divs - Calculate clock dividers 1003 * @f: I2C clock frequency 1004 * @input_clk: Input clock frequency 1005 * @a: First divider (return value) 1006 * @b: Second divider (return value) 1007 * 1008 * f is used as input and output variable. As input it is used as target I2C 1009 * frequency. On function exit f holds the actually resulting I2C frequency. 1010 * 1011 * Return: 0 on success, negative errno otherwise. 1012 */ 1013 static int cdns_i2c_calc_divs(unsigned long *f, unsigned long input_clk, 1014 unsigned int *a, unsigned int *b) 1015 { 1016 unsigned long fscl = *f, best_fscl = *f, actual_fscl, temp; 1017 unsigned int div_a, div_b, calc_div_a = 0, calc_div_b = 0; 1018 unsigned int last_error, current_error; 1019 1020 /* calculate (divisor_a+1) x (divisor_b+1) */ 1021 temp = input_clk / (22 * fscl); 1022 1023 /* 1024 * If the calculated value is negative or 0, the fscl input is out of 1025 * range. Return error. 1026 */ 1027 if (!temp || (temp > (CDNS_I2C_DIVA_MAX * CDNS_I2C_DIVB_MAX))) 1028 return -EINVAL; 1029 1030 last_error = -1; 1031 for (div_a = 0; div_a < CDNS_I2C_DIVA_MAX; div_a++) { 1032 div_b = DIV_ROUND_UP(input_clk, 22 * fscl * (div_a + 1)); 1033 1034 if ((div_b < 1) || (div_b > CDNS_I2C_DIVB_MAX)) 1035 continue; 1036 div_b--; 1037 1038 actual_fscl = input_clk / (22 * (div_a + 1) * (div_b + 1)); 1039 1040 if (actual_fscl > fscl) 1041 continue; 1042 1043 current_error = fscl - actual_fscl; 1044 1045 if (last_error > current_error) { 1046 calc_div_a = div_a; 1047 calc_div_b = div_b; 1048 best_fscl = actual_fscl; 1049 last_error = current_error; 1050 } 1051 } 1052 1053 *a = calc_div_a; 1054 *b = calc_div_b; 1055 *f = best_fscl; 1056 1057 return 0; 1058 } 1059 1060 /** 1061 * cdns_i2c_setclk - This function sets the serial clock rate for the I2C device 1062 * @clk_in: I2C clock input frequency in Hz 1063 * @id: Pointer to the I2C device structure 1064 * 1065 * The device must be idle rather than busy transferring data before setting 1066 * these device options. 1067 * The data rate is set by values in the control register. 1068 * The formula for determining the correct register values is 1069 * Fscl = Fpclk/(22 x (divisor_a+1) x (divisor_b+1)) 1070 * See the hardware data sheet for a full explanation of setting the serial 1071 * clock rate. The clock can not be faster than the input clock divide by 22. 1072 * The two most common clock rates are 100KHz and 400KHz. 1073 * 1074 * Return: 0 on success, negative error otherwise 1075 */ 1076 static int cdns_i2c_setclk(unsigned long clk_in, struct cdns_i2c *id) 1077 { 1078 unsigned int div_a, div_b; 1079 unsigned int ctrl_reg; 1080 int ret = 0; 1081 unsigned long fscl = id->i2c_clk; 1082 1083 ret = cdns_i2c_calc_divs(&fscl, clk_in, &div_a, &div_b); 1084 if (ret) 1085 return ret; 1086 1087 ctrl_reg = id->ctrl_reg; 1088 ctrl_reg &= ~(CDNS_I2C_CR_DIVA_MASK | CDNS_I2C_CR_DIVB_MASK); 1089 ctrl_reg |= ((div_a << CDNS_I2C_CR_DIVA_SHIFT) | 1090 (div_b << CDNS_I2C_CR_DIVB_SHIFT)); 1091 id->ctrl_reg = ctrl_reg; 1092 cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET); 1093 #if IS_ENABLED(CONFIG_I2C_SLAVE) 1094 id->ctrl_reg_diva_divb = ctrl_reg & (CDNS_I2C_CR_DIVA_MASK | 1095 CDNS_I2C_CR_DIVB_MASK); 1096 #endif 1097 return 0; 1098 } 1099 1100 /** 1101 * cdns_i2c_clk_notifier_cb - Clock rate change callback 1102 * @nb: Pointer to notifier block 1103 * @event: Notification reason 1104 * @data: Pointer to notification data object 1105 * 1106 * This function is called when the cdns_i2c input clock frequency changes. 1107 * The callback checks whether a valid bus frequency can be generated after the 1108 * change. If so, the change is acknowledged, otherwise the change is aborted. 1109 * New dividers are written to the HW in the pre- or post change notification 1110 * depending on the scaling direction. 1111 * 1112 * Return: NOTIFY_STOP if the rate change should be aborted, NOTIFY_OK 1113 * to acknowledge the change, NOTIFY_DONE if the notification is 1114 * considered irrelevant. 1115 */ 1116 static int cdns_i2c_clk_notifier_cb(struct notifier_block *nb, unsigned long 1117 event, void *data) 1118 { 1119 struct clk_notifier_data *ndata = data; 1120 struct cdns_i2c *id = to_cdns_i2c(nb); 1121 1122 if (pm_runtime_suspended(id->dev)) 1123 return NOTIFY_OK; 1124 1125 switch (event) { 1126 case PRE_RATE_CHANGE: 1127 { 1128 unsigned long input_clk = ndata->new_rate; 1129 unsigned long fscl = id->i2c_clk; 1130 unsigned int div_a, div_b; 1131 int ret; 1132 1133 ret = cdns_i2c_calc_divs(&fscl, input_clk, &div_a, &div_b); 1134 if (ret) { 1135 dev_warn(id->adap.dev.parent, 1136 "clock rate change rejected\n"); 1137 return NOTIFY_STOP; 1138 } 1139 1140 /* scale up */ 1141 if (ndata->new_rate > ndata->old_rate) 1142 cdns_i2c_setclk(ndata->new_rate, id); 1143 1144 return NOTIFY_OK; 1145 } 1146 case POST_RATE_CHANGE: 1147 id->input_clk = ndata->new_rate; 1148 /* scale down */ 1149 if (ndata->new_rate < ndata->old_rate) 1150 cdns_i2c_setclk(ndata->new_rate, id); 1151 return NOTIFY_OK; 1152 case ABORT_RATE_CHANGE: 1153 /* scale up */ 1154 if (ndata->new_rate > ndata->old_rate) 1155 cdns_i2c_setclk(ndata->old_rate, id); 1156 return NOTIFY_OK; 1157 default: 1158 return NOTIFY_DONE; 1159 } 1160 } 1161 1162 /** 1163 * cdns_i2c_runtime_suspend - Runtime suspend method for the driver 1164 * @dev: Address of the platform_device structure 1165 * 1166 * Put the driver into low power mode. 1167 * 1168 * Return: 0 always 1169 */ 1170 static int __maybe_unused cdns_i2c_runtime_suspend(struct device *dev) 1171 { 1172 struct cdns_i2c *xi2c = dev_get_drvdata(dev); 1173 1174 clk_disable(xi2c->clk); 1175 1176 return 0; 1177 } 1178 1179 static int __maybe_unused cdns_i2c_suspend(struct device *dev) 1180 { 1181 struct cdns_i2c *xi2c = dev_get_drvdata(dev); 1182 1183 i2c_mark_adapter_suspended(&xi2c->adap); 1184 1185 if (!pm_runtime_status_suspended(dev)) 1186 return cdns_i2c_runtime_suspend(dev); 1187 1188 return 0; 1189 } 1190 1191 /** 1192 * cdns_i2c_init - Controller initialisation 1193 * @id: Device private data structure 1194 * 1195 * Initialise the i2c controller. 1196 * 1197 */ 1198 static void cdns_i2c_init(struct cdns_i2c *id) 1199 { 1200 cdns_i2c_writereg(id->ctrl_reg, CDNS_I2C_CR_OFFSET); 1201 /* 1202 * Cadence I2C controller has a bug wherein it generates 1203 * invalid read transaction after HW timeout in master receiver mode. 1204 * HW timeout is not used by this driver and the interrupt is disabled. 1205 * But the feature itself cannot be disabled. Hence maximum value 1206 * is written to this register to reduce the chances of error. 1207 */ 1208 cdns_i2c_writereg(CDNS_I2C_TIMEOUT_MAX, CDNS_I2C_TIME_OUT_OFFSET); 1209 } 1210 1211 /** 1212 * cdns_i2c_runtime_resume - Runtime resume 1213 * @dev: Address of the platform_device structure 1214 * 1215 * Runtime resume callback. 1216 * 1217 * Return: 0 on success and error value on error 1218 */ 1219 static int __maybe_unused cdns_i2c_runtime_resume(struct device *dev) 1220 { 1221 struct cdns_i2c *xi2c = dev_get_drvdata(dev); 1222 int ret; 1223 1224 ret = clk_enable(xi2c->clk); 1225 if (ret) { 1226 dev_err(dev, "Cannot enable clock.\n"); 1227 return ret; 1228 } 1229 cdns_i2c_init(xi2c); 1230 1231 return 0; 1232 } 1233 1234 static int __maybe_unused cdns_i2c_resume(struct device *dev) 1235 { 1236 struct cdns_i2c *xi2c = dev_get_drvdata(dev); 1237 int err; 1238 1239 err = cdns_i2c_runtime_resume(dev); 1240 if (err) 1241 return err; 1242 1243 if (pm_runtime_status_suspended(dev)) { 1244 err = cdns_i2c_runtime_suspend(dev); 1245 if (err) 1246 return err; 1247 } 1248 1249 i2c_mark_adapter_resumed(&xi2c->adap); 1250 1251 return 0; 1252 } 1253 1254 static const struct dev_pm_ops cdns_i2c_dev_pm_ops = { 1255 SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(cdns_i2c_suspend, cdns_i2c_resume) 1256 SET_RUNTIME_PM_OPS(cdns_i2c_runtime_suspend, 1257 cdns_i2c_runtime_resume, NULL) 1258 }; 1259 1260 static const struct cdns_platform_data r1p10_i2c_def = { 1261 .quirks = CDNS_I2C_BROKEN_HOLD_BIT, 1262 }; 1263 1264 static const struct of_device_id cdns_i2c_of_match[] = { 1265 { .compatible = "cdns,i2c-r1p10", .data = &r1p10_i2c_def }, 1266 { .compatible = "cdns,i2c-r1p14",}, 1267 { /* end of table */ } 1268 }; 1269 MODULE_DEVICE_TABLE(of, cdns_i2c_of_match); 1270 1271 /** 1272 * cdns_i2c_detect_transfer_size - Detect the maximum transfer size supported 1273 * @id: Device private data structure 1274 * 1275 * Detect the maximum transfer size that is supported by this instance of the 1276 * Cadence I2C controller. 1277 */ 1278 static void cdns_i2c_detect_transfer_size(struct cdns_i2c *id) 1279 { 1280 u32 val; 1281 1282 /* 1283 * Writing to the transfer size register is only possible if these two bits 1284 * are set in the control register. 1285 */ 1286 cdns_i2c_writereg(CDNS_I2C_CR_MS | CDNS_I2C_CR_RW, CDNS_I2C_CR_OFFSET); 1287 1288 /* 1289 * The number of writable bits of the transfer size register can be between 1290 * 4 and 8. This is a controlled through a synthesis parameter of the IP 1291 * core and can vary from instance to instance. The unused MSBs always read 1292 * back as 0. Writing 0xff and then reading the value back will report the 1293 * maximum supported transfer size. 1294 */ 1295 cdns_i2c_writereg(CDNS_I2C_MAX_TRANSFER_SIZE, CDNS_I2C_XFER_SIZE_OFFSET); 1296 val = cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET); 1297 id->transfer_size = CDNS_I2C_TRANSFER_SIZE(val); 1298 cdns_i2c_writereg(0, CDNS_I2C_XFER_SIZE_OFFSET); 1299 cdns_i2c_writereg(0, CDNS_I2C_CR_OFFSET); 1300 } 1301 1302 /** 1303 * cdns_i2c_probe - Platform registration call 1304 * @pdev: Handle to the platform device structure 1305 * 1306 * This function does all the memory allocation and registration for the i2c 1307 * device. User can modify the address mode to 10 bit address mode using the 1308 * ioctl call with option I2C_TENBIT. 1309 * 1310 * Return: 0 on success, negative error otherwise 1311 */ 1312 static int cdns_i2c_probe(struct platform_device *pdev) 1313 { 1314 struct resource *r_mem; 1315 struct cdns_i2c *id; 1316 int ret, irq; 1317 const struct of_device_id *match; 1318 1319 id = devm_kzalloc(&pdev->dev, sizeof(*id), GFP_KERNEL); 1320 if (!id) 1321 return -ENOMEM; 1322 1323 id->dev = &pdev->dev; 1324 platform_set_drvdata(pdev, id); 1325 1326 match = of_match_node(cdns_i2c_of_match, pdev->dev.of_node); 1327 if (match && match->data) { 1328 const struct cdns_platform_data *data = match->data; 1329 id->quirks = data->quirks; 1330 } 1331 1332 id->rinfo.pinctrl = devm_pinctrl_get(&pdev->dev); 1333 if (IS_ERR(id->rinfo.pinctrl)) { 1334 int err = PTR_ERR(id->rinfo.pinctrl); 1335 1336 dev_info(&pdev->dev, "can't get pinctrl, bus recovery not supported\n"); 1337 if (err != -ENODEV) 1338 return err; 1339 } else { 1340 id->adap.bus_recovery_info = &id->rinfo; 1341 } 1342 1343 id->membase = devm_platform_get_and_ioremap_resource(pdev, 0, &r_mem); 1344 if (IS_ERR(id->membase)) 1345 return PTR_ERR(id->membase); 1346 1347 irq = platform_get_irq(pdev, 0); 1348 if (irq < 0) 1349 return irq; 1350 1351 id->adap.owner = THIS_MODULE; 1352 id->adap.dev.of_node = pdev->dev.of_node; 1353 id->adap.algo = &cdns_i2c_algo; 1354 id->adap.timeout = CDNS_I2C_TIMEOUT; 1355 id->adap.retries = 3; /* Default retry value. */ 1356 id->adap.algo_data = id; 1357 id->adap.dev.parent = &pdev->dev; 1358 init_completion(&id->xfer_done); 1359 snprintf(id->adap.name, sizeof(id->adap.name), 1360 "Cadence I2C at %08lx", (unsigned long)r_mem->start); 1361 1362 id->clk = devm_clk_get(&pdev->dev, NULL); 1363 if (IS_ERR(id->clk)) 1364 return dev_err_probe(&pdev->dev, PTR_ERR(id->clk), 1365 "input clock not found.\n"); 1366 1367 id->reset = devm_reset_control_get_optional_shared(&pdev->dev, NULL); 1368 if (IS_ERR(id->reset)) 1369 return dev_err_probe(&pdev->dev, PTR_ERR(id->reset), 1370 "Failed to request reset.\n"); 1371 1372 ret = clk_prepare_enable(id->clk); 1373 if (ret) 1374 dev_err(&pdev->dev, "Unable to enable clock.\n"); 1375 1376 ret = reset_control_deassert(id->reset); 1377 if (ret) { 1378 dev_err_probe(&pdev->dev, ret, 1379 "Failed to de-assert reset.\n"); 1380 goto err_clk_dis; 1381 } 1382 1383 pm_runtime_set_autosuspend_delay(id->dev, CNDS_I2C_PM_TIMEOUT); 1384 pm_runtime_use_autosuspend(id->dev); 1385 pm_runtime_set_active(id->dev); 1386 pm_runtime_enable(id->dev); 1387 1388 id->clk_rate_change_nb.notifier_call = cdns_i2c_clk_notifier_cb; 1389 if (clk_notifier_register(id->clk, &id->clk_rate_change_nb)) 1390 dev_warn(&pdev->dev, "Unable to register clock notifier.\n"); 1391 id->input_clk = clk_get_rate(id->clk); 1392 1393 ret = of_property_read_u32(pdev->dev.of_node, "clock-frequency", 1394 &id->i2c_clk); 1395 if (ret || (id->i2c_clk > I2C_MAX_FAST_MODE_FREQ)) 1396 id->i2c_clk = I2C_MAX_STANDARD_MODE_FREQ; 1397 1398 #if IS_ENABLED(CONFIG_I2C_SLAVE) 1399 /* Set initial mode to master */ 1400 id->dev_mode = CDNS_I2C_MODE_MASTER; 1401 id->slave_state = CDNS_I2C_SLAVE_STATE_IDLE; 1402 #endif 1403 id->ctrl_reg = CDNS_I2C_CR_ACK_EN | CDNS_I2C_CR_NEA | CDNS_I2C_CR_MS; 1404 1405 id->fifo_depth = CDNS_I2C_FIFO_DEPTH_DEFAULT; 1406 of_property_read_u32(pdev->dev.of_node, "fifo-depth", &id->fifo_depth); 1407 1408 cdns_i2c_detect_transfer_size(id); 1409 1410 ret = cdns_i2c_setclk(id->input_clk, id); 1411 if (ret) { 1412 dev_err(&pdev->dev, "invalid SCL clock: %u Hz\n", id->i2c_clk); 1413 ret = -EINVAL; 1414 goto err_clk_notifier_unregister; 1415 } 1416 1417 ret = devm_request_irq(&pdev->dev, irq, cdns_i2c_isr, 0, 1418 DRIVER_NAME, id); 1419 if (ret) { 1420 dev_err(&pdev->dev, "cannot get irq %d\n", irq); 1421 goto err_clk_notifier_unregister; 1422 } 1423 cdns_i2c_init(id); 1424 1425 ret = i2c_add_adapter(&id->adap); 1426 if (ret < 0) 1427 goto err_clk_notifier_unregister; 1428 1429 dev_info(&pdev->dev, "%u kHz mmio %08lx irq %d\n", 1430 id->i2c_clk / 1000, (unsigned long)r_mem->start, irq); 1431 1432 return 0; 1433 1434 err_clk_notifier_unregister: 1435 clk_notifier_unregister(id->clk, &id->clk_rate_change_nb); 1436 reset_control_assert(id->reset); 1437 err_clk_dis: 1438 clk_disable_unprepare(id->clk); 1439 pm_runtime_disable(&pdev->dev); 1440 pm_runtime_set_suspended(&pdev->dev); 1441 return ret; 1442 } 1443 1444 /** 1445 * cdns_i2c_remove - Unregister the device after releasing the resources 1446 * @pdev: Handle to the platform device structure 1447 * 1448 * This function frees all the resources allocated to the device. 1449 * 1450 * Return: 0 always 1451 */ 1452 static void cdns_i2c_remove(struct platform_device *pdev) 1453 { 1454 struct cdns_i2c *id = platform_get_drvdata(pdev); 1455 1456 pm_runtime_disable(&pdev->dev); 1457 pm_runtime_set_suspended(&pdev->dev); 1458 pm_runtime_dont_use_autosuspend(&pdev->dev); 1459 1460 i2c_del_adapter(&id->adap); 1461 clk_notifier_unregister(id->clk, &id->clk_rate_change_nb); 1462 reset_control_assert(id->reset); 1463 clk_disable_unprepare(id->clk); 1464 } 1465 1466 static struct platform_driver cdns_i2c_drv = { 1467 .driver = { 1468 .name = DRIVER_NAME, 1469 .of_match_table = cdns_i2c_of_match, 1470 .pm = &cdns_i2c_dev_pm_ops, 1471 }, 1472 .probe = cdns_i2c_probe, 1473 .remove_new = cdns_i2c_remove, 1474 }; 1475 1476 module_platform_driver(cdns_i2c_drv); 1477 1478 MODULE_AUTHOR("Xilinx Inc."); 1479 MODULE_DESCRIPTION("Cadence I2C bus driver"); 1480 MODULE_LICENSE("GPL"); 1481