1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * Driver for Jedec 5118 compliant temperature sensors 4 * 5 * Derived from https://github.com/Steve-Tech/SPD5118-DKMS 6 * Originally from T/2 driver at https://t2sde.org/packages/linux 7 * Copyright (c) 2023 René Rebe, ExactCODE GmbH; Germany. 8 * 9 * Copyright (c) 2024 Guenter Roeck 10 * 11 * Inspired by ee1004.c and jc42.c. 12 * 13 * SPD5118 compliant temperature sensors are typically used on DDR5 14 * memory modules. 15 */ 16 17 #include <linux/bitops.h> 18 #include <linux/bits.h> 19 #include <linux/err.h> 20 #include <linux/i2c.h> 21 #include <linux/hwmon.h> 22 #include <linux/module.h> 23 #include <linux/mutex.h> 24 #include <linux/nvmem-provider.h> 25 #include <linux/pm.h> 26 #include <linux/regmap.h> 27 #include <linux/units.h> 28 29 /* Addresses to scan */ 30 static const unsigned short normal_i2c[] = { 31 0x50, 0x51, 0x52, 0x53, 0x54, 0x55, 0x56, 0x57, I2C_CLIENT_END }; 32 33 /* SPD5118 registers. */ 34 #define SPD5118_REG_TYPE 0x00 /* MR0:MR1 */ 35 #define SPD5118_REG_REVISION 0x02 /* MR2 */ 36 #define SPD5118_REG_VENDOR 0x03 /* MR3:MR4 */ 37 #define SPD5118_REG_CAPABILITY 0x05 /* MR5 */ 38 #define SPD5118_REG_I2C_LEGACY_MODE 0x0B /* MR11 */ 39 #define SPD5118_REG_TEMP_CLR 0x13 /* MR19 */ 40 #define SPD5118_REG_ERROR_CLR 0x14 /* MR20 */ 41 #define SPD5118_REG_TEMP_CONFIG 0x1A /* MR26 */ 42 #define SPD5118_REG_TEMP_MAX 0x1c /* MR28:MR29 */ 43 #define SPD5118_REG_TEMP_MIN 0x1e /* MR30:MR31 */ 44 #define SPD5118_REG_TEMP_CRIT 0x20 /* MR32:MR33 */ 45 #define SPD5118_REG_TEMP_LCRIT 0x22 /* MR34:MR35 */ 46 #define SPD5118_REG_TEMP 0x31 /* MR49:MR50 */ 47 #define SPD5118_REG_TEMP_STATUS 0x33 /* MR51 */ 48 49 #define SPD5118_TEMP_STATUS_HIGH BIT(0) 50 #define SPD5118_TEMP_STATUS_LOW BIT(1) 51 #define SPD5118_TEMP_STATUS_CRIT BIT(2) 52 #define SPD5118_TEMP_STATUS_LCRIT BIT(3) 53 54 #define SPD5118_CAP_TS_SUPPORT BIT(1) /* temperature sensor support */ 55 56 #define SPD5118_TS_DISABLE BIT(0) /* temperature sensor disable */ 57 58 #define SPD5118_LEGACY_MODE_ADDR BIT(3) 59 #define SPD5118_LEGACY_PAGE_MASK GENMASK(2, 0) 60 #define SPD5118_LEGACY_MODE_MASK (SPD5118_LEGACY_MODE_ADDR | SPD5118_LEGACY_PAGE_MASK) 61 62 #define SPD5118_NUM_PAGES 8 63 #define SPD5118_PAGE_SIZE 128 64 #define SPD5118_PAGE_SHIFT 7 65 #define SPD5118_PAGE_MASK GENMASK(6, 0) 66 #define SPD5118_EEPROM_BASE 0x80 67 #define SPD5118_EEPROM_SIZE (SPD5118_PAGE_SIZE * SPD5118_NUM_PAGES) 68 69 /* Temperature unit in millicelsius */ 70 #define SPD5118_TEMP_UNIT (MILLIDEGREE_PER_DEGREE / 4) 71 /* Representable temperature range in millicelsius */ 72 #define SPD5118_TEMP_RANGE_MIN -256000 73 #define SPD5118_TEMP_RANGE_MAX 255750 74 75 struct spd5118_data { 76 struct regmap *regmap; 77 struct mutex nvmem_lock; 78 }; 79 80 /* hwmon */ 81 82 static int spd5118_temp_from_reg(u16 reg) 83 { 84 int temp = sign_extend32(reg >> 2, 10); 85 86 return temp * SPD5118_TEMP_UNIT; 87 } 88 89 static u16 spd5118_temp_to_reg(long temp) 90 { 91 temp = clamp_val(temp, SPD5118_TEMP_RANGE_MIN, SPD5118_TEMP_RANGE_MAX); 92 return (DIV_ROUND_CLOSEST(temp, SPD5118_TEMP_UNIT) & 0x7ff) << 2; 93 } 94 95 static int spd5118_read_temp(struct regmap *regmap, u32 attr, long *val) 96 { 97 int reg, err; 98 u8 regval[2]; 99 u16 temp; 100 101 switch (attr) { 102 case hwmon_temp_input: 103 reg = SPD5118_REG_TEMP; 104 break; 105 case hwmon_temp_max: 106 reg = SPD5118_REG_TEMP_MAX; 107 break; 108 case hwmon_temp_min: 109 reg = SPD5118_REG_TEMP_MIN; 110 break; 111 case hwmon_temp_crit: 112 reg = SPD5118_REG_TEMP_CRIT; 113 break; 114 case hwmon_temp_lcrit: 115 reg = SPD5118_REG_TEMP_LCRIT; 116 break; 117 default: 118 return -EOPNOTSUPP; 119 } 120 121 err = regmap_bulk_read(regmap, reg, regval, 2); 122 if (err) 123 return err; 124 125 temp = (regval[1] << 8) | regval[0]; 126 127 *val = spd5118_temp_from_reg(temp); 128 return 0; 129 } 130 131 static int spd5118_read_alarm(struct regmap *regmap, u32 attr, long *val) 132 { 133 unsigned int mask, regval; 134 int err; 135 136 switch (attr) { 137 case hwmon_temp_max_alarm: 138 mask = SPD5118_TEMP_STATUS_HIGH; 139 break; 140 case hwmon_temp_min_alarm: 141 mask = SPD5118_TEMP_STATUS_LOW; 142 break; 143 case hwmon_temp_crit_alarm: 144 mask = SPD5118_TEMP_STATUS_CRIT; 145 break; 146 case hwmon_temp_lcrit_alarm: 147 mask = SPD5118_TEMP_STATUS_LCRIT; 148 break; 149 default: 150 return -EOPNOTSUPP; 151 } 152 153 err = regmap_read(regmap, SPD5118_REG_TEMP_STATUS, ®val); 154 if (err < 0) 155 return err; 156 *val = !!(regval & mask); 157 if (*val) 158 return regmap_write(regmap, SPD5118_REG_TEMP_CLR, mask); 159 return 0; 160 } 161 162 static int spd5118_read_enable(struct regmap *regmap, long *val) 163 { 164 u32 regval; 165 int err; 166 167 err = regmap_read(regmap, SPD5118_REG_TEMP_CONFIG, ®val); 168 if (err < 0) 169 return err; 170 *val = !(regval & SPD5118_TS_DISABLE); 171 return 0; 172 } 173 174 static int spd5118_read(struct device *dev, enum hwmon_sensor_types type, 175 u32 attr, int channel, long *val) 176 { 177 struct regmap *regmap = dev_get_drvdata(dev); 178 179 if (type != hwmon_temp) 180 return -EOPNOTSUPP; 181 182 switch (attr) { 183 case hwmon_temp_input: 184 case hwmon_temp_max: 185 case hwmon_temp_min: 186 case hwmon_temp_crit: 187 case hwmon_temp_lcrit: 188 return spd5118_read_temp(regmap, attr, val); 189 case hwmon_temp_max_alarm: 190 case hwmon_temp_min_alarm: 191 case hwmon_temp_crit_alarm: 192 case hwmon_temp_lcrit_alarm: 193 return spd5118_read_alarm(regmap, attr, val); 194 case hwmon_temp_enable: 195 return spd5118_read_enable(regmap, val); 196 default: 197 return -EOPNOTSUPP; 198 } 199 } 200 201 static int spd5118_write_temp(struct regmap *regmap, u32 attr, long val) 202 { 203 u8 regval[2]; 204 u16 temp; 205 int reg; 206 207 switch (attr) { 208 case hwmon_temp_max: 209 reg = SPD5118_REG_TEMP_MAX; 210 break; 211 case hwmon_temp_min: 212 reg = SPD5118_REG_TEMP_MIN; 213 break; 214 case hwmon_temp_crit: 215 reg = SPD5118_REG_TEMP_CRIT; 216 break; 217 case hwmon_temp_lcrit: 218 reg = SPD5118_REG_TEMP_LCRIT; 219 break; 220 default: 221 return -EOPNOTSUPP; 222 } 223 224 temp = spd5118_temp_to_reg(val); 225 regval[0] = temp & 0xff; 226 regval[1] = temp >> 8; 227 228 return regmap_bulk_write(regmap, reg, regval, 2); 229 } 230 231 static int spd5118_write_enable(struct regmap *regmap, long val) 232 { 233 if (val && val != 1) 234 return -EINVAL; 235 236 return regmap_update_bits(regmap, SPD5118_REG_TEMP_CONFIG, 237 SPD5118_TS_DISABLE, 238 val ? 0 : SPD5118_TS_DISABLE); 239 } 240 241 static int spd5118_temp_write(struct regmap *regmap, u32 attr, long val) 242 { 243 switch (attr) { 244 case hwmon_temp_max: 245 case hwmon_temp_min: 246 case hwmon_temp_crit: 247 case hwmon_temp_lcrit: 248 return spd5118_write_temp(regmap, attr, val); 249 case hwmon_temp_enable: 250 return spd5118_write_enable(regmap, val); 251 default: 252 return -EOPNOTSUPP; 253 } 254 } 255 256 static int spd5118_write(struct device *dev, enum hwmon_sensor_types type, 257 u32 attr, int channel, long val) 258 { 259 struct regmap *regmap = dev_get_drvdata(dev); 260 261 switch (type) { 262 case hwmon_temp: 263 return spd5118_temp_write(regmap, attr, val); 264 default: 265 return -EOPNOTSUPP; 266 } 267 } 268 269 static umode_t spd5118_is_visible(const void *_data, enum hwmon_sensor_types type, 270 u32 attr, int channel) 271 { 272 if (type != hwmon_temp) 273 return 0; 274 275 switch (attr) { 276 case hwmon_temp_input: 277 return 0444; 278 case hwmon_temp_min: 279 case hwmon_temp_max: 280 case hwmon_temp_lcrit: 281 case hwmon_temp_crit: 282 case hwmon_temp_enable: 283 return 0644; 284 case hwmon_temp_min_alarm: 285 case hwmon_temp_max_alarm: 286 case hwmon_temp_crit_alarm: 287 case hwmon_temp_lcrit_alarm: 288 return 0444; 289 default: 290 return 0; 291 } 292 } 293 294 /* 295 * Bank and vendor id are 8-bit fields with seven data bits and odd parity. 296 * Vendor IDs 0 and 0x7f are invalid. 297 * See Jedec standard JEP106BJ for details and a list of assigned vendor IDs. 298 */ 299 static bool spd5118_vendor_valid(u8 bank, u8 id) 300 { 301 if (parity8(bank) == 0 || parity8(id) == 0) 302 return false; 303 304 id &= 0x7f; 305 return id && id != 0x7f; 306 } 307 308 /* Return 0 if detection is successful, -ENODEV otherwise */ 309 static int spd5118_detect(struct i2c_client *client, struct i2c_board_info *info) 310 { 311 struct i2c_adapter *adapter = client->adapter; 312 int regval; 313 314 if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA | 315 I2C_FUNC_SMBUS_WORD_DATA)) 316 return -ENODEV; 317 318 regval = i2c_smbus_read_word_swapped(client, SPD5118_REG_TYPE); 319 if (regval != 0x5118) 320 return -ENODEV; 321 322 regval = i2c_smbus_read_word_data(client, SPD5118_REG_VENDOR); 323 if (regval < 0 || !spd5118_vendor_valid(regval & 0xff, regval >> 8)) 324 return -ENODEV; 325 326 regval = i2c_smbus_read_byte_data(client, SPD5118_REG_CAPABILITY); 327 if (regval < 0) 328 return -ENODEV; 329 if (!(regval & SPD5118_CAP_TS_SUPPORT) || (regval & 0xfc)) 330 return -ENODEV; 331 332 regval = i2c_smbus_read_byte_data(client, SPD5118_REG_TEMP_CLR); 333 if (regval) 334 return -ENODEV; 335 regval = i2c_smbus_read_byte_data(client, SPD5118_REG_ERROR_CLR); 336 if (regval) 337 return -ENODEV; 338 339 regval = i2c_smbus_read_byte_data(client, SPD5118_REG_REVISION); 340 if (regval < 0 || (regval & 0xc1)) 341 return -ENODEV; 342 343 regval = i2c_smbus_read_byte_data(client, SPD5118_REG_TEMP_CONFIG); 344 if (regval < 0) 345 return -ENODEV; 346 if (regval & ~SPD5118_TS_DISABLE) 347 return -ENODEV; 348 349 strscpy(info->type, "spd5118", I2C_NAME_SIZE); 350 return 0; 351 } 352 353 static const struct hwmon_channel_info *spd5118_info[] = { 354 HWMON_CHANNEL_INFO(chip, 355 HWMON_C_REGISTER_TZ), 356 HWMON_CHANNEL_INFO(temp, 357 HWMON_T_INPUT | 358 HWMON_T_LCRIT | HWMON_T_LCRIT_ALARM | 359 HWMON_T_MIN | HWMON_T_MIN_ALARM | 360 HWMON_T_MAX | HWMON_T_MAX_ALARM | 361 HWMON_T_CRIT | HWMON_T_CRIT_ALARM | 362 HWMON_T_ENABLE), 363 NULL 364 }; 365 366 static const struct hwmon_ops spd5118_hwmon_ops = { 367 .is_visible = spd5118_is_visible, 368 .read = spd5118_read, 369 .write = spd5118_write, 370 }; 371 372 static const struct hwmon_chip_info spd5118_chip_info = { 373 .ops = &spd5118_hwmon_ops, 374 .info = spd5118_info, 375 }; 376 377 /* nvmem */ 378 379 static ssize_t spd5118_nvmem_read_page(struct regmap *regmap, char *buf, 380 unsigned int offset, size_t count) 381 { 382 int addr = (offset >> SPD5118_PAGE_SHIFT) * 0x100 + SPD5118_EEPROM_BASE; 383 int err; 384 385 offset &= SPD5118_PAGE_MASK; 386 387 /* Can't cross page boundaries */ 388 if (offset + count > SPD5118_PAGE_SIZE) 389 count = SPD5118_PAGE_SIZE - offset; 390 391 err = regmap_bulk_read(regmap, addr + offset, buf, count); 392 if (err) 393 return err; 394 395 return count; 396 } 397 398 static int spd5118_nvmem_read(void *priv, unsigned int off, void *val, size_t count) 399 { 400 struct spd5118_data *data = priv; 401 char *buf = val; 402 int ret; 403 404 if (unlikely(!count)) 405 return count; 406 407 if (off + count > SPD5118_EEPROM_SIZE) 408 return -EINVAL; 409 410 mutex_lock(&data->nvmem_lock); 411 412 while (count) { 413 ret = spd5118_nvmem_read_page(data->regmap, buf, off, count); 414 if (ret < 0) { 415 mutex_unlock(&data->nvmem_lock); 416 return ret; 417 } 418 buf += ret; 419 off += ret; 420 count -= ret; 421 } 422 mutex_unlock(&data->nvmem_lock); 423 return 0; 424 } 425 426 static int spd5118_nvmem_init(struct device *dev, struct spd5118_data *data) 427 { 428 struct nvmem_config nvmem_config = { 429 .type = NVMEM_TYPE_EEPROM, 430 .name = dev_name(dev), 431 .id = NVMEM_DEVID_NONE, 432 .dev = dev, 433 .base_dev = dev, 434 .read_only = true, 435 .root_only = false, 436 .owner = THIS_MODULE, 437 .compat = true, 438 .reg_read = spd5118_nvmem_read, 439 .priv = data, 440 .stride = 1, 441 .word_size = 1, 442 .size = SPD5118_EEPROM_SIZE, 443 }; 444 struct nvmem_device *nvmem; 445 446 nvmem = devm_nvmem_register(dev, &nvmem_config); 447 return PTR_ERR_OR_ZERO(nvmem); 448 } 449 450 /* regmap */ 451 452 static bool spd5118_writeable_reg(struct device *dev, unsigned int reg) 453 { 454 switch (reg) { 455 case SPD5118_REG_I2C_LEGACY_MODE: 456 case SPD5118_REG_TEMP_CLR: 457 case SPD5118_REG_TEMP_CONFIG: 458 case SPD5118_REG_TEMP_MAX: 459 case SPD5118_REG_TEMP_MAX + 1: 460 case SPD5118_REG_TEMP_MIN: 461 case SPD5118_REG_TEMP_MIN + 1: 462 case SPD5118_REG_TEMP_CRIT: 463 case SPD5118_REG_TEMP_CRIT + 1: 464 case SPD5118_REG_TEMP_LCRIT: 465 case SPD5118_REG_TEMP_LCRIT + 1: 466 return true; 467 default: 468 return false; 469 } 470 } 471 472 static bool spd5118_volatile_reg(struct device *dev, unsigned int reg) 473 { 474 switch (reg) { 475 case SPD5118_REG_TEMP_CLR: 476 case SPD5118_REG_ERROR_CLR: 477 case SPD5118_REG_TEMP: 478 case SPD5118_REG_TEMP + 1: 479 case SPD5118_REG_TEMP_STATUS: 480 return true; 481 default: 482 return false; 483 } 484 } 485 486 static const struct regmap_range_cfg spd5118_regmap_range_cfg[] = { 487 { 488 .selector_reg = SPD5118_REG_I2C_LEGACY_MODE, 489 .selector_mask = SPD5118_LEGACY_PAGE_MASK, 490 .selector_shift = 0, 491 .window_start = 0, 492 .window_len = 0x100, 493 .range_min = 0, 494 .range_max = 0x7ff, 495 }, 496 }; 497 498 static const struct regmap_config spd5118_regmap_config = { 499 .reg_bits = 8, 500 .val_bits = 8, 501 .max_register = 0x7ff, 502 .writeable_reg = spd5118_writeable_reg, 503 .volatile_reg = spd5118_volatile_reg, 504 .cache_type = REGCACHE_MAPLE, 505 506 .ranges = spd5118_regmap_range_cfg, 507 .num_ranges = ARRAY_SIZE(spd5118_regmap_range_cfg), 508 }; 509 510 static int spd5118_init(struct i2c_client *client) 511 { 512 struct i2c_adapter *adapter = client->adapter; 513 int err, regval, mode; 514 515 if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA | 516 I2C_FUNC_SMBUS_WORD_DATA)) 517 return -ENODEV; 518 519 regval = i2c_smbus_read_word_swapped(client, SPD5118_REG_TYPE); 520 if (regval < 0 || (regval && regval != 0x5118)) 521 return -ENODEV; 522 523 /* 524 * If the device type registers return 0, it is possible that the chip 525 * has a non-zero page selected and takes the specification literally, 526 * i.e. disables access to volatile registers besides the page register 527 * if the page is not 0. Try to identify such chips. 528 */ 529 if (!regval) { 530 /* Vendor ID registers must also be 0 */ 531 regval = i2c_smbus_read_word_data(client, SPD5118_REG_VENDOR); 532 if (regval) 533 return -ENODEV; 534 535 /* The selected page in MR11 must not be 0 */ 536 mode = i2c_smbus_read_byte_data(client, SPD5118_REG_I2C_LEGACY_MODE); 537 if (mode < 0 || (mode & ~SPD5118_LEGACY_MODE_MASK) || 538 !(mode & SPD5118_LEGACY_PAGE_MASK)) 539 return -ENODEV; 540 541 err = i2c_smbus_write_byte_data(client, SPD5118_REG_I2C_LEGACY_MODE, 542 mode & SPD5118_LEGACY_MODE_ADDR); 543 if (err) 544 return -ENODEV; 545 546 /* 547 * If the device type registers are still bad after selecting 548 * page 0, this is not a SPD5118 device. Restore original 549 * legacy mode register value and abort. 550 */ 551 regval = i2c_smbus_read_word_swapped(client, SPD5118_REG_TYPE); 552 if (regval != 0x5118) { 553 i2c_smbus_write_byte_data(client, SPD5118_REG_I2C_LEGACY_MODE, mode); 554 return -ENODEV; 555 } 556 } 557 558 /* We are reasonably sure that this is really a SPD5118 hub controller */ 559 return 0; 560 } 561 562 static int spd5118_probe(struct i2c_client *client) 563 { 564 struct device *dev = &client->dev; 565 unsigned int regval, revision, vendor, bank; 566 struct spd5118_data *data; 567 struct device *hwmon_dev; 568 struct regmap *regmap; 569 int err; 570 571 err = spd5118_init(client); 572 if (err) 573 return err; 574 575 data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL); 576 if (!data) 577 return -ENOMEM; 578 579 regmap = devm_regmap_init_i2c(client, &spd5118_regmap_config); 580 if (IS_ERR(regmap)) 581 return dev_err_probe(dev, PTR_ERR(regmap), "regmap init failed\n"); 582 583 err = regmap_read(regmap, SPD5118_REG_CAPABILITY, ®val); 584 if (err) 585 return err; 586 if (!(regval & SPD5118_CAP_TS_SUPPORT)) 587 return -ENODEV; 588 589 err = regmap_read(regmap, SPD5118_REG_REVISION, &revision); 590 if (err) 591 return err; 592 593 err = regmap_read(regmap, SPD5118_REG_VENDOR, &bank); 594 if (err) 595 return err; 596 err = regmap_read(regmap, SPD5118_REG_VENDOR + 1, &vendor); 597 if (err) 598 return err; 599 if (!spd5118_vendor_valid(bank, vendor)) 600 return -ENODEV; 601 602 data->regmap = regmap; 603 mutex_init(&data->nvmem_lock); 604 dev_set_drvdata(dev, data); 605 606 err = spd5118_nvmem_init(dev, data); 607 /* Ignore if NVMEM support is disabled */ 608 if (err && err != -EOPNOTSUPP) { 609 dev_err_probe(dev, err, "failed to register nvmem\n"); 610 return err; 611 } 612 613 hwmon_dev = devm_hwmon_device_register_with_info(dev, "spd5118", 614 regmap, &spd5118_chip_info, 615 NULL); 616 if (IS_ERR(hwmon_dev)) 617 return PTR_ERR(hwmon_dev); 618 619 /* 620 * From JESD300-5B 621 * MR2 bits [5:4]: Major revision, 1..4 622 * MR2 bits [3:1]: Minor revision, 0..8? Probably a typo, assume 1..8 623 */ 624 dev_info(dev, "DDR5 temperature sensor: vendor 0x%02x:0x%02x revision %d.%d\n", 625 bank & 0x7f, vendor, ((revision >> 4) & 0x03) + 1, ((revision >> 1) & 0x07) + 1); 626 627 return 0; 628 } 629 630 static int spd5118_suspend(struct device *dev) 631 { 632 struct spd5118_data *data = dev_get_drvdata(dev); 633 struct regmap *regmap = data->regmap; 634 u32 regval; 635 int err; 636 637 /* 638 * Make sure the configuration register in the regmap cache is current 639 * before bypassing it. 640 */ 641 err = regmap_read(regmap, SPD5118_REG_TEMP_CONFIG, ®val); 642 if (err < 0) 643 return err; 644 645 regcache_cache_bypass(regmap, true); 646 regmap_update_bits(regmap, SPD5118_REG_TEMP_CONFIG, SPD5118_TS_DISABLE, 647 SPD5118_TS_DISABLE); 648 regcache_cache_bypass(regmap, false); 649 650 regcache_cache_only(regmap, true); 651 regcache_mark_dirty(regmap); 652 653 return 0; 654 } 655 656 static int spd5118_resume(struct device *dev) 657 { 658 struct spd5118_data *data = dev_get_drvdata(dev); 659 struct regmap *regmap = data->regmap; 660 661 regcache_cache_only(regmap, false); 662 return regcache_sync(regmap); 663 } 664 665 static DEFINE_SIMPLE_DEV_PM_OPS(spd5118_pm_ops, spd5118_suspend, spd5118_resume); 666 667 static const struct i2c_device_id spd5118_id[] = { 668 { "spd5118" }, 669 { } 670 }; 671 MODULE_DEVICE_TABLE(i2c, spd5118_id); 672 673 static const struct of_device_id spd5118_of_ids[] = { 674 { .compatible = "jedec,spd5118", }, 675 { } 676 }; 677 MODULE_DEVICE_TABLE(of, spd5118_of_ids); 678 679 static struct i2c_driver spd5118_driver = { 680 .class = I2C_CLASS_HWMON, 681 .driver = { 682 .name = "spd5118", 683 .of_match_table = spd5118_of_ids, 684 .pm = pm_sleep_ptr(&spd5118_pm_ops), 685 }, 686 .probe = spd5118_probe, 687 .id_table = spd5118_id, 688 .detect = IS_ENABLED(CONFIG_SENSORS_SPD5118_DETECT) ? spd5118_detect : NULL, 689 .address_list = IS_ENABLED(CONFIG_SENSORS_SPD5118_DETECT) ? normal_i2c : NULL, 690 }; 691 692 module_i2c_driver(spd5118_driver); 693 694 MODULE_AUTHOR("René Rebe <rene@exactcode.de>"); 695 MODULE_AUTHOR("Guenter Roeck <linux@roeck-us.net>"); 696 MODULE_DESCRIPTION("SPD 5118 driver"); 697 MODULE_LICENSE("GPL"); 698