1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Copyright (C) 2020 MaxLinear, Inc. 4 * 5 * This driver is a hardware monitoring driver for PVT controller 6 * (MR75203) which is used to configure & control Moortec embedded 7 * analog IP to enable multiple embedded temperature sensor(TS), 8 * voltage monitor(VM) & process detector(PD) modules. 9 */ 10 #include <linux/bits.h> 11 #include <linux/clk.h> 12 #include <linux/debugfs.h> 13 #include <linux/hwmon.h> 14 #include <linux/kstrtox.h> 15 #include <linux/module.h> 16 #include <linux/mod_devicetable.h> 17 #include <linux/mutex.h> 18 #include <linux/platform_device.h> 19 #include <linux/property.h> 20 #include <linux/regmap.h> 21 #include <linux/reset.h> 22 #include <linux/slab.h> 23 #include <linux/units.h> 24 25 /* PVT Common register */ 26 #define PVT_IP_CONFIG 0x04 27 #define TS_NUM_MSK GENMASK(4, 0) 28 #define TS_NUM_SFT 0 29 #define PD_NUM_MSK GENMASK(12, 8) 30 #define PD_NUM_SFT 8 31 #define VM_NUM_MSK GENMASK(20, 16) 32 #define VM_NUM_SFT 16 33 #define CH_NUM_MSK GENMASK(31, 24) 34 #define CH_NUM_SFT 24 35 36 #define VM_NUM_MAX (VM_NUM_MSK >> VM_NUM_SFT) 37 38 /* Macro Common Register */ 39 #define CLK_SYNTH 0x00 40 #define CLK_SYNTH_LO_SFT 0 41 #define CLK_SYNTH_HI_SFT 8 42 #define CLK_SYNTH_HOLD_SFT 16 43 #define CLK_SYNTH_EN BIT(24) 44 #define CLK_SYS_CYCLES_MAX 514 45 #define CLK_SYS_CYCLES_MIN 2 46 47 #define SDIF_DISABLE 0x04 48 49 #define SDIF_STAT 0x08 50 #define SDIF_BUSY BIT(0) 51 #define SDIF_LOCK BIT(1) 52 53 #define SDIF_W 0x0c 54 #define SDIF_PROG BIT(31) 55 #define SDIF_WRN_W BIT(27) 56 #define SDIF_WRN_R 0x00 57 #define SDIF_ADDR_SFT 24 58 59 #define SDIF_HALT 0x10 60 #define SDIF_CTRL 0x14 61 #define SDIF_SMPL_CTRL 0x20 62 63 /* TS & PD Individual Macro Register */ 64 #define COM_REG_SIZE 0x40 65 66 #define SDIF_DONE(n) (COM_REG_SIZE + 0x14 + 0x40 * (n)) 67 #define SDIF_SMPL_DONE BIT(0) 68 69 #define SDIF_DATA(n) (COM_REG_SIZE + 0x18 + 0x40 * (n)) 70 #define SAMPLE_DATA_MSK GENMASK(15, 0) 71 72 #define HILO_RESET(n) (COM_REG_SIZE + 0x2c + 0x40 * (n)) 73 74 /* VM Individual Macro Register */ 75 #define VM_COM_REG_SIZE 0x200 76 #define VM_SDIF_DONE(vm) (VM_COM_REG_SIZE + 0x34 + 0x200 * (vm)) 77 #define VM_SDIF_DATA(vm, ch) \ 78 (VM_COM_REG_SIZE + 0x40 + 0x200 * (vm) + 0x4 * (ch)) 79 80 /* SDA Slave Register */ 81 #define IP_CTRL 0x00 82 #define IP_RST_REL BIT(1) 83 #define IP_RUN_CONT BIT(3) 84 #define IP_AUTO BIT(8) 85 #define IP_VM_MODE BIT(10) 86 87 #define IP_CFG 0x01 88 #define CFG0_MODE_2 BIT(0) 89 #define CFG0_PARALLEL_OUT 0 90 #define CFG0_12_BIT 0 91 #define CFG1_VOL_MEAS_MODE 0 92 #define CFG1_PARALLEL_OUT 0 93 #define CFG1_14_BIT 0 94 95 #define IP_DATA 0x03 96 97 #define IP_POLL 0x04 98 #define VM_CH_INIT BIT(20) 99 #define VM_CH_REQ BIT(21) 100 101 #define IP_TMR 0x05 102 #define POWER_DELAY_CYCLE_256 0x100 103 #define POWER_DELAY_CYCLE_64 0x40 104 105 #define PVT_POLL_DELAY_US 20 106 #define PVT_POLL_TIMEOUT_US 20000 107 #define PVT_CONV_BITS 10 108 #define PVT_N_CONST 90 109 #define PVT_R_CONST 245805 110 111 #define PVT_TEMP_MIN_mC -40000 112 #define PVT_TEMP_MAX_mC 125000 113 114 /* Temperature coefficients for series 5 */ 115 #define PVT_SERIES5_H_CONST 200000 116 #define PVT_SERIES5_G_CONST 60000 117 #define PVT_SERIES5_J_CONST -100 118 #define PVT_SERIES5_CAL5_CONST 4094 119 120 /* Temperature coefficients for series 6 */ 121 #define PVT_SERIES6_H_CONST 249400 122 #define PVT_SERIES6_G_CONST 57400 123 #define PVT_SERIES6_J_CONST 0 124 #define PVT_SERIES6_CAL5_CONST 4096 125 126 #define TEMPERATURE_SENSOR_SERIES_5 5 127 #define TEMPERATURE_SENSOR_SERIES_6 6 128 129 #define PRE_SCALER_X1 1 130 #define PRE_SCALER_X2 2 131 132 /** 133 * struct voltage_device - VM single input parameters. 134 * @vm_map: Map channel number to VM index. 135 * @ch_map: Map channel number to channel index. 136 * @pre_scaler: Pre scaler value (1 or 2) used to normalize the voltage output 137 * result. 138 * 139 * The structure provides mapping between channel-number (0..N-1) to VM-index 140 * (0..num_vm-1) and channel-index (0..ch_num-1) where N = num_vm * ch_num. 141 * It also provides normalization factor for the VM equation. 142 */ 143 struct voltage_device { 144 u32 vm_map; 145 u32 ch_map; 146 u32 pre_scaler; 147 }; 148 149 /** 150 * struct voltage_channels - VM channel count. 151 * @total: Total number of channels in all VMs. 152 * @max: Maximum number of channels among all VMs. 153 * 154 * The structure provides channel count information across all VMs. 155 */ 156 struct voltage_channels { 157 u32 total; 158 u8 max; 159 }; 160 161 struct temp_coeff { 162 u32 h; 163 u32 g; 164 u32 cal5; 165 s32 j; 166 }; 167 168 struct pvt_device { 169 struct regmap *c_map; 170 struct regmap *t_map; 171 struct regmap *p_map; 172 struct regmap *v_map; 173 struct clk *clk; 174 struct reset_control *rst; 175 struct dentry *dbgfs_dir; 176 struct voltage_device *vd; 177 struct voltage_channels vm_channels; 178 struct temp_coeff ts_coeff; 179 u32 t_num; 180 u32 p_num; 181 u32 v_num; 182 u32 ip_freq; 183 }; 184 185 static ssize_t pvt_ts_coeff_j_read(struct file *file, char __user *user_buf, 186 size_t count, loff_t *ppos) 187 { 188 struct pvt_device *pvt = file->private_data; 189 unsigned int len; 190 char buf[13]; 191 192 len = scnprintf(buf, sizeof(buf), "%d\n", pvt->ts_coeff.j); 193 194 return simple_read_from_buffer(user_buf, count, ppos, buf, len); 195 } 196 197 static ssize_t pvt_ts_coeff_j_write(struct file *file, 198 const char __user *user_buf, 199 size_t count, loff_t *ppos) 200 { 201 struct pvt_device *pvt = file->private_data; 202 int ret; 203 204 ret = kstrtos32_from_user(user_buf, count, 0, &pvt->ts_coeff.j); 205 if (ret) 206 return ret; 207 208 return count; 209 } 210 211 static const struct file_operations pvt_ts_coeff_j_fops = { 212 .read = pvt_ts_coeff_j_read, 213 .write = pvt_ts_coeff_j_write, 214 .open = simple_open, 215 .owner = THIS_MODULE, 216 .llseek = default_llseek, 217 }; 218 219 static void devm_pvt_ts_dbgfs_remove(void *data) 220 { 221 struct pvt_device *pvt = (struct pvt_device *)data; 222 223 debugfs_remove_recursive(pvt->dbgfs_dir); 224 pvt->dbgfs_dir = NULL; 225 } 226 227 static int pvt_ts_dbgfs_create(struct pvt_device *pvt, struct device *dev) 228 { 229 pvt->dbgfs_dir = debugfs_create_dir(dev_name(dev), NULL); 230 231 debugfs_create_u32("ts_coeff_h", 0644, pvt->dbgfs_dir, 232 &pvt->ts_coeff.h); 233 debugfs_create_u32("ts_coeff_g", 0644, pvt->dbgfs_dir, 234 &pvt->ts_coeff.g); 235 debugfs_create_u32("ts_coeff_cal5", 0644, pvt->dbgfs_dir, 236 &pvt->ts_coeff.cal5); 237 debugfs_create_file("ts_coeff_j", 0644, pvt->dbgfs_dir, pvt, 238 &pvt_ts_coeff_j_fops); 239 240 return devm_add_action_or_reset(dev, devm_pvt_ts_dbgfs_remove, pvt); 241 } 242 243 static umode_t pvt_is_visible(const void *data, enum hwmon_sensor_types type, 244 u32 attr, int channel) 245 { 246 switch (type) { 247 case hwmon_temp: 248 if (attr == hwmon_temp_input) 249 return 0444; 250 break; 251 case hwmon_in: 252 if (attr == hwmon_in_input) 253 return 0444; 254 break; 255 default: 256 break; 257 } 258 return 0; 259 } 260 261 static long pvt_calc_temp(struct pvt_device *pvt, u32 nbs) 262 { 263 /* 264 * Convert the register value to degrees centigrade temperature: 265 * T = G + H * (n / cal5 - 0.5) + J * F 266 */ 267 struct temp_coeff *ts_coeff = &pvt->ts_coeff; 268 269 s64 tmp = ts_coeff->g + 270 div_s64(ts_coeff->h * (s64)nbs, ts_coeff->cal5) - 271 ts_coeff->h / 2 + 272 div_s64(ts_coeff->j * (s64)pvt->ip_freq, HZ_PER_MHZ); 273 274 return clamp_val(tmp, PVT_TEMP_MIN_mC, PVT_TEMP_MAX_mC); 275 } 276 277 static int pvt_read_temp(struct device *dev, u32 attr, int channel, long *val) 278 { 279 struct pvt_device *pvt = dev_get_drvdata(dev); 280 struct regmap *t_map = pvt->t_map; 281 u32 stat, nbs; 282 int ret; 283 284 switch (attr) { 285 case hwmon_temp_input: 286 ret = regmap_read_poll_timeout(t_map, SDIF_DONE(channel), 287 stat, stat & SDIF_SMPL_DONE, 288 PVT_POLL_DELAY_US, 289 PVT_POLL_TIMEOUT_US); 290 if (ret) 291 return ret; 292 293 ret = regmap_read(t_map, SDIF_DATA(channel), &nbs); 294 if (ret < 0) 295 return ret; 296 297 nbs &= SAMPLE_DATA_MSK; 298 299 /* 300 * Convert the register value to 301 * degrees centigrade temperature 302 */ 303 *val = pvt_calc_temp(pvt, nbs); 304 305 return 0; 306 default: 307 return -EOPNOTSUPP; 308 } 309 } 310 311 static int pvt_read_in(struct device *dev, u32 attr, int channel, long *val) 312 { 313 struct pvt_device *pvt = dev_get_drvdata(dev); 314 struct regmap *v_map = pvt->v_map; 315 u32 n, stat, pre_scaler; 316 u8 vm_idx, ch_idx; 317 int ret; 318 319 if (channel >= pvt->vm_channels.total) 320 return -EINVAL; 321 322 vm_idx = pvt->vd[channel].vm_map; 323 ch_idx = pvt->vd[channel].ch_map; 324 325 switch (attr) { 326 case hwmon_in_input: 327 ret = regmap_read_poll_timeout(v_map, VM_SDIF_DONE(vm_idx), 328 stat, stat & SDIF_SMPL_DONE, 329 PVT_POLL_DELAY_US, 330 PVT_POLL_TIMEOUT_US); 331 if (ret) 332 return ret; 333 334 ret = regmap_read(v_map, VM_SDIF_DATA(vm_idx, ch_idx), &n); 335 if (ret < 0) 336 return ret; 337 338 n &= SAMPLE_DATA_MSK; 339 pre_scaler = pvt->vd[channel].pre_scaler; 340 /* 341 * Convert the N bitstream count into voltage. 342 * To support negative voltage calculation for 64bit machines 343 * n must be cast to long, since n and *val differ both in 344 * signedness and in size. 345 * Division is used instead of right shift, because for signed 346 * numbers, the sign bit is used to fill the vacated bit 347 * positions, and if the number is negative, 1 is used. 348 * BIT(x) may not be used instead of (1 << x) because it's 349 * unsigned. 350 */ 351 *val = pre_scaler * (PVT_N_CONST * (long)n - PVT_R_CONST) / 352 (1 << PVT_CONV_BITS); 353 354 return 0; 355 default: 356 return -EOPNOTSUPP; 357 } 358 } 359 360 static int pvt_read(struct device *dev, enum hwmon_sensor_types type, 361 u32 attr, int channel, long *val) 362 { 363 switch (type) { 364 case hwmon_temp: 365 return pvt_read_temp(dev, attr, channel, val); 366 case hwmon_in: 367 return pvt_read_in(dev, attr, channel, val); 368 default: 369 return -EOPNOTSUPP; 370 } 371 } 372 373 static struct hwmon_channel_info pvt_temp = { 374 .type = hwmon_temp, 375 }; 376 377 static struct hwmon_channel_info pvt_in = { 378 .type = hwmon_in, 379 }; 380 381 static const struct hwmon_ops pvt_hwmon_ops = { 382 .is_visible = pvt_is_visible, 383 .read = pvt_read, 384 }; 385 386 static struct hwmon_chip_info pvt_chip_info = { 387 .ops = &pvt_hwmon_ops, 388 }; 389 390 static int pvt_init(struct pvt_device *pvt) 391 { 392 u16 sys_freq, key, middle, low = 4, high = 8; 393 struct regmap *t_map = pvt->t_map; 394 struct regmap *p_map = pvt->p_map; 395 struct regmap *v_map = pvt->v_map; 396 u32 t_num = pvt->t_num; 397 u32 p_num = pvt->p_num; 398 u32 v_num = pvt->v_num; 399 u32 clk_synth, val; 400 int ret; 401 402 sys_freq = clk_get_rate(pvt->clk) / HZ_PER_MHZ; 403 while (high >= low) { 404 middle = (low + high + 1) / 2; 405 key = DIV_ROUND_CLOSEST(sys_freq, middle); 406 if (key > CLK_SYS_CYCLES_MAX) { 407 low = middle + 1; 408 continue; 409 } else if (key < CLK_SYS_CYCLES_MIN) { 410 high = middle - 1; 411 continue; 412 } else { 413 break; 414 } 415 } 416 417 /* 418 * The system supports 'clk_sys' to 'clk_ip' frequency ratios 419 * from 2:1 to 512:1 420 */ 421 key = clamp_val(key, CLK_SYS_CYCLES_MIN, CLK_SYS_CYCLES_MAX) - 2; 422 423 clk_synth = ((key + 1) >> 1) << CLK_SYNTH_LO_SFT | 424 (key >> 1) << CLK_SYNTH_HI_SFT | 425 (key >> 1) << CLK_SYNTH_HOLD_SFT | CLK_SYNTH_EN; 426 427 pvt->ip_freq = clk_get_rate(pvt->clk) / (key + 2); 428 429 if (t_num) { 430 ret = regmap_write(t_map, SDIF_SMPL_CTRL, 0x0); 431 if (ret < 0) 432 return ret; 433 434 ret = regmap_write(t_map, SDIF_HALT, 0x0); 435 if (ret < 0) 436 return ret; 437 438 ret = regmap_write(t_map, CLK_SYNTH, clk_synth); 439 if (ret < 0) 440 return ret; 441 442 ret = regmap_write(t_map, SDIF_DISABLE, 0x0); 443 if (ret < 0) 444 return ret; 445 446 ret = regmap_read_poll_timeout(t_map, SDIF_STAT, 447 val, !(val & SDIF_BUSY), 448 PVT_POLL_DELAY_US, 449 PVT_POLL_TIMEOUT_US); 450 if (ret) 451 return ret; 452 453 val = CFG0_MODE_2 | CFG0_PARALLEL_OUT | CFG0_12_BIT | 454 IP_CFG << SDIF_ADDR_SFT | SDIF_WRN_W | SDIF_PROG; 455 ret = regmap_write(t_map, SDIF_W, val); 456 if (ret < 0) 457 return ret; 458 459 ret = regmap_read_poll_timeout(t_map, SDIF_STAT, 460 val, !(val & SDIF_BUSY), 461 PVT_POLL_DELAY_US, 462 PVT_POLL_TIMEOUT_US); 463 if (ret) 464 return ret; 465 466 val = POWER_DELAY_CYCLE_256 | IP_TMR << SDIF_ADDR_SFT | 467 SDIF_WRN_W | SDIF_PROG; 468 ret = regmap_write(t_map, SDIF_W, val); 469 if (ret < 0) 470 return ret; 471 472 ret = regmap_read_poll_timeout(t_map, SDIF_STAT, 473 val, !(val & SDIF_BUSY), 474 PVT_POLL_DELAY_US, 475 PVT_POLL_TIMEOUT_US); 476 if (ret) 477 return ret; 478 479 val = IP_RST_REL | IP_RUN_CONT | IP_AUTO | 480 IP_CTRL << SDIF_ADDR_SFT | 481 SDIF_WRN_W | SDIF_PROG; 482 ret = regmap_write(t_map, SDIF_W, val); 483 if (ret < 0) 484 return ret; 485 } 486 487 if (p_num) { 488 ret = regmap_write(p_map, SDIF_HALT, 0x0); 489 if (ret < 0) 490 return ret; 491 492 ret = regmap_write(p_map, SDIF_DISABLE, BIT(p_num) - 1); 493 if (ret < 0) 494 return ret; 495 496 ret = regmap_write(p_map, CLK_SYNTH, clk_synth); 497 if (ret < 0) 498 return ret; 499 } 500 501 if (v_num) { 502 ret = regmap_write(v_map, SDIF_SMPL_CTRL, 0x0); 503 if (ret < 0) 504 return ret; 505 506 ret = regmap_write(v_map, SDIF_HALT, 0x0); 507 if (ret < 0) 508 return ret; 509 510 ret = regmap_write(v_map, CLK_SYNTH, clk_synth); 511 if (ret < 0) 512 return ret; 513 514 ret = regmap_write(v_map, SDIF_DISABLE, 0x0); 515 if (ret < 0) 516 return ret; 517 518 ret = regmap_read_poll_timeout(v_map, SDIF_STAT, 519 val, !(val & SDIF_BUSY), 520 PVT_POLL_DELAY_US, 521 PVT_POLL_TIMEOUT_US); 522 if (ret) 523 return ret; 524 525 val = (BIT(pvt->vm_channels.max) - 1) | VM_CH_INIT | 526 IP_POLL << SDIF_ADDR_SFT | SDIF_WRN_W | SDIF_PROG; 527 ret = regmap_write(v_map, SDIF_W, val); 528 if (ret < 0) 529 return ret; 530 531 ret = regmap_read_poll_timeout(v_map, SDIF_STAT, 532 val, !(val & SDIF_BUSY), 533 PVT_POLL_DELAY_US, 534 PVT_POLL_TIMEOUT_US); 535 if (ret) 536 return ret; 537 538 val = CFG1_VOL_MEAS_MODE | CFG1_PARALLEL_OUT | 539 CFG1_14_BIT | IP_CFG << SDIF_ADDR_SFT | 540 SDIF_WRN_W | SDIF_PROG; 541 ret = regmap_write(v_map, SDIF_W, val); 542 if (ret < 0) 543 return ret; 544 545 ret = regmap_read_poll_timeout(v_map, SDIF_STAT, 546 val, !(val & SDIF_BUSY), 547 PVT_POLL_DELAY_US, 548 PVT_POLL_TIMEOUT_US); 549 if (ret) 550 return ret; 551 552 val = POWER_DELAY_CYCLE_64 | IP_TMR << SDIF_ADDR_SFT | 553 SDIF_WRN_W | SDIF_PROG; 554 ret = regmap_write(v_map, SDIF_W, val); 555 if (ret < 0) 556 return ret; 557 558 ret = regmap_read_poll_timeout(v_map, SDIF_STAT, 559 val, !(val & SDIF_BUSY), 560 PVT_POLL_DELAY_US, 561 PVT_POLL_TIMEOUT_US); 562 if (ret) 563 return ret; 564 565 val = IP_RST_REL | IP_RUN_CONT | IP_AUTO | IP_VM_MODE | 566 IP_CTRL << SDIF_ADDR_SFT | 567 SDIF_WRN_W | SDIF_PROG; 568 ret = regmap_write(v_map, SDIF_W, val); 569 if (ret < 0) 570 return ret; 571 } 572 573 return 0; 574 } 575 576 static struct regmap_config pvt_regmap_config = { 577 .reg_bits = 32, 578 .reg_stride = 4, 579 .val_bits = 32, 580 }; 581 582 static int pvt_get_regmap(struct platform_device *pdev, char *reg_name, 583 struct pvt_device *pvt) 584 { 585 struct device *dev = &pdev->dev; 586 struct regmap **reg_map; 587 void __iomem *io_base; 588 589 if (!strcmp(reg_name, "common")) 590 reg_map = &pvt->c_map; 591 else if (!strcmp(reg_name, "ts")) 592 reg_map = &pvt->t_map; 593 else if (!strcmp(reg_name, "pd")) 594 reg_map = &pvt->p_map; 595 else if (!strcmp(reg_name, "vm")) 596 reg_map = &pvt->v_map; 597 else 598 return -EINVAL; 599 600 io_base = devm_platform_ioremap_resource_byname(pdev, reg_name); 601 if (IS_ERR(io_base)) 602 return PTR_ERR(io_base); 603 604 pvt_regmap_config.name = reg_name; 605 *reg_map = devm_regmap_init_mmio(dev, io_base, &pvt_regmap_config); 606 if (IS_ERR(*reg_map)) { 607 dev_err(dev, "failed to init register map\n"); 608 return PTR_ERR(*reg_map); 609 } 610 611 return 0; 612 } 613 614 static void pvt_reset_control_assert(void *data) 615 { 616 struct pvt_device *pvt = data; 617 618 reset_control_assert(pvt->rst); 619 } 620 621 static int pvt_reset_control_deassert(struct device *dev, struct pvt_device *pvt) 622 { 623 int ret; 624 625 ret = reset_control_deassert(pvt->rst); 626 if (ret) 627 return ret; 628 629 return devm_add_action_or_reset(dev, pvt_reset_control_assert, pvt); 630 } 631 632 static int pvt_get_active_channel(struct device *dev, struct pvt_device *pvt, 633 u32 vm_num, u32 ch_num, u8 *vm_idx) 634 { 635 u8 vm_active_ch[VM_NUM_MAX]; 636 int ret, i, j, k; 637 638 ret = device_property_read_u8_array(dev, "moortec,vm-active-channels", 639 vm_active_ch, vm_num); 640 if (ret) { 641 /* 642 * Incase "moortec,vm-active-channels" property is not defined, 643 * we assume each VM sensor has all of its channels active. 644 */ 645 memset(vm_active_ch, ch_num, vm_num); 646 pvt->vm_channels.max = ch_num; 647 pvt->vm_channels.total = ch_num * vm_num; 648 } else { 649 for (i = 0; i < vm_num; i++) { 650 if (vm_active_ch[i] > ch_num) { 651 dev_err(dev, "invalid active channels: %u\n", 652 vm_active_ch[i]); 653 return -EINVAL; 654 } 655 656 pvt->vm_channels.total += vm_active_ch[i]; 657 658 if (vm_active_ch[i] > pvt->vm_channels.max) 659 pvt->vm_channels.max = vm_active_ch[i]; 660 } 661 } 662 663 /* 664 * Map between the channel-number to VM-index and channel-index. 665 * Example - 3 VMs, "moortec,vm_active_ch" = <5 2 4>: 666 * vm_map = [0 0 0 0 0 1 1 2 2 2 2] 667 * ch_map = [0 1 2 3 4 0 1 0 1 2 3] 668 */ 669 pvt->vd = devm_kcalloc(dev, pvt->vm_channels.total, sizeof(*pvt->vd), 670 GFP_KERNEL); 671 if (!pvt->vd) 672 return -ENOMEM; 673 674 k = 0; 675 for (i = 0; i < vm_num; i++) { 676 for (j = 0; j < vm_active_ch[i]; j++) { 677 pvt->vd[k].vm_map = vm_idx[i]; 678 pvt->vd[k].ch_map = j; 679 k++; 680 } 681 } 682 683 return 0; 684 } 685 686 static int pvt_get_pre_scaler(struct device *dev, struct pvt_device *pvt) 687 { 688 u8 *pre_scaler_ch_list; 689 int i, ret, num_ch; 690 u32 channel; 691 692 /* Set default pre-scaler value to be 1. */ 693 for (i = 0; i < pvt->vm_channels.total; i++) 694 pvt->vd[i].pre_scaler = PRE_SCALER_X1; 695 696 /* Get number of channels configured in "moortec,vm-pre-scaler-x2". */ 697 num_ch = device_property_count_u8(dev, "moortec,vm-pre-scaler-x2"); 698 if (num_ch <= 0) 699 return 0; 700 701 pre_scaler_ch_list = kcalloc(num_ch, sizeof(*pre_scaler_ch_list), 702 GFP_KERNEL); 703 if (!pre_scaler_ch_list) 704 return -ENOMEM; 705 706 /* Get list of all channels that have pre-scaler of 2. */ 707 ret = device_property_read_u8_array(dev, "moortec,vm-pre-scaler-x2", 708 pre_scaler_ch_list, num_ch); 709 if (ret) 710 goto out; 711 712 for (i = 0; i < num_ch; i++) { 713 channel = pre_scaler_ch_list[i]; 714 pvt->vd[channel].pre_scaler = PRE_SCALER_X2; 715 } 716 717 out: 718 kfree(pre_scaler_ch_list); 719 720 return ret; 721 } 722 723 static int pvt_set_temp_coeff(struct device *dev, struct pvt_device *pvt) 724 { 725 struct temp_coeff *ts_coeff = &pvt->ts_coeff; 726 u32 series; 727 int ret; 728 729 /* Incase ts-series property is not defined, use default 5. */ 730 ret = device_property_read_u32(dev, "moortec,ts-series", &series); 731 if (ret) 732 series = TEMPERATURE_SENSOR_SERIES_5; 733 734 switch (series) { 735 case TEMPERATURE_SENSOR_SERIES_5: 736 ts_coeff->h = PVT_SERIES5_H_CONST; 737 ts_coeff->g = PVT_SERIES5_G_CONST; 738 ts_coeff->j = PVT_SERIES5_J_CONST; 739 ts_coeff->cal5 = PVT_SERIES5_CAL5_CONST; 740 break; 741 case TEMPERATURE_SENSOR_SERIES_6: 742 ts_coeff->h = PVT_SERIES6_H_CONST; 743 ts_coeff->g = PVT_SERIES6_G_CONST; 744 ts_coeff->j = PVT_SERIES6_J_CONST; 745 ts_coeff->cal5 = PVT_SERIES6_CAL5_CONST; 746 break; 747 default: 748 dev_err(dev, "invalid temperature sensor series (%u)\n", 749 series); 750 return -EINVAL; 751 } 752 753 dev_dbg(dev, "temperature sensor series = %u\n", series); 754 755 /* Override ts-coeff-h/g/j/cal5 if they are defined. */ 756 device_property_read_u32(dev, "moortec,ts-coeff-h", &ts_coeff->h); 757 device_property_read_u32(dev, "moortec,ts-coeff-g", &ts_coeff->g); 758 device_property_read_u32(dev, "moortec,ts-coeff-j", &ts_coeff->j); 759 device_property_read_u32(dev, "moortec,ts-coeff-cal5", &ts_coeff->cal5); 760 761 dev_dbg(dev, "ts-coeff: h = %u, g = %u, j = %d, cal5 = %u\n", 762 ts_coeff->h, ts_coeff->g, ts_coeff->j, ts_coeff->cal5); 763 764 return 0; 765 } 766 767 static int mr75203_probe(struct platform_device *pdev) 768 { 769 u32 ts_num, vm_num, pd_num, ch_num, val, index, i; 770 const struct hwmon_channel_info **pvt_info; 771 struct device *dev = &pdev->dev; 772 u32 *temp_config, *in_config; 773 struct device *hwmon_dev; 774 struct pvt_device *pvt; 775 int ret; 776 777 pvt = devm_kzalloc(dev, sizeof(*pvt), GFP_KERNEL); 778 if (!pvt) 779 return -ENOMEM; 780 781 ret = pvt_get_regmap(pdev, "common", pvt); 782 if (ret) 783 return ret; 784 785 pvt->clk = devm_clk_get_enabled(dev, NULL); 786 if (IS_ERR(pvt->clk)) 787 return dev_err_probe(dev, PTR_ERR(pvt->clk), "failed to get clock\n"); 788 789 pvt->rst = devm_reset_control_get_optional_exclusive(dev, NULL); 790 if (IS_ERR(pvt->rst)) 791 return dev_err_probe(dev, PTR_ERR(pvt->rst), 792 "failed to get reset control\n"); 793 794 if (pvt->rst) { 795 ret = pvt_reset_control_deassert(dev, pvt); 796 if (ret) 797 return dev_err_probe(dev, ret, 798 "cannot deassert reset control\n"); 799 } 800 801 ret = regmap_read(pvt->c_map, PVT_IP_CONFIG, &val); 802 if (ret < 0) 803 return ret; 804 805 ts_num = (val & TS_NUM_MSK) >> TS_NUM_SFT; 806 pd_num = (val & PD_NUM_MSK) >> PD_NUM_SFT; 807 vm_num = (val & VM_NUM_MSK) >> VM_NUM_SFT; 808 ch_num = (val & CH_NUM_MSK) >> CH_NUM_SFT; 809 pvt->t_num = ts_num; 810 pvt->p_num = pd_num; 811 pvt->v_num = vm_num; 812 val = 0; 813 if (ts_num) 814 val++; 815 if (vm_num) 816 val++; 817 if (!val) 818 return -ENODEV; 819 820 pvt_info = devm_kcalloc(dev, val + 2, sizeof(*pvt_info), GFP_KERNEL); 821 if (!pvt_info) 822 return -ENOMEM; 823 pvt_info[0] = HWMON_CHANNEL_INFO(chip, HWMON_C_REGISTER_TZ); 824 index = 1; 825 826 if (ts_num) { 827 ret = pvt_get_regmap(pdev, "ts", pvt); 828 if (ret) 829 return ret; 830 831 ret = pvt_set_temp_coeff(dev, pvt); 832 if (ret) 833 return ret; 834 835 temp_config = devm_kcalloc(dev, ts_num + 1, 836 sizeof(*temp_config), GFP_KERNEL); 837 if (!temp_config) 838 return -ENOMEM; 839 840 memset32(temp_config, HWMON_T_INPUT, ts_num); 841 pvt_temp.config = temp_config; 842 pvt_info[index++] = &pvt_temp; 843 844 pvt_ts_dbgfs_create(pvt, dev); 845 } 846 847 if (pd_num) { 848 ret = pvt_get_regmap(pdev, "pd", pvt); 849 if (ret) 850 return ret; 851 } 852 853 if (vm_num) { 854 u8 vm_idx[VM_NUM_MAX]; 855 856 ret = pvt_get_regmap(pdev, "vm", pvt); 857 if (ret) 858 return ret; 859 860 ret = device_property_read_u8_array(dev, "intel,vm-map", vm_idx, 861 vm_num); 862 if (ret) { 863 /* 864 * Incase intel,vm-map property is not defined, we 865 * assume incremental channel numbers. 866 */ 867 for (i = 0; i < vm_num; i++) 868 vm_idx[i] = i; 869 } else { 870 for (i = 0; i < vm_num; i++) 871 if (vm_idx[i] >= vm_num || vm_idx[i] == 0xff) { 872 pvt->v_num = i; 873 vm_num = i; 874 break; 875 } 876 } 877 878 ret = pvt_get_active_channel(dev, pvt, vm_num, ch_num, vm_idx); 879 if (ret) 880 return ret; 881 882 ret = pvt_get_pre_scaler(dev, pvt); 883 if (ret) 884 return ret; 885 886 in_config = devm_kcalloc(dev, pvt->vm_channels.total + 1, 887 sizeof(*in_config), GFP_KERNEL); 888 if (!in_config) 889 return -ENOMEM; 890 891 memset32(in_config, HWMON_I_INPUT, pvt->vm_channels.total); 892 in_config[pvt->vm_channels.total] = 0; 893 pvt_in.config = in_config; 894 895 pvt_info[index++] = &pvt_in; 896 } 897 898 ret = pvt_init(pvt); 899 if (ret) { 900 dev_err(dev, "failed to init pvt: %d\n", ret); 901 return ret; 902 } 903 904 pvt_chip_info.info = pvt_info; 905 hwmon_dev = devm_hwmon_device_register_with_info(dev, "pvt", 906 pvt, 907 &pvt_chip_info, 908 NULL); 909 910 return PTR_ERR_OR_ZERO(hwmon_dev); 911 } 912 913 static const struct of_device_id moortec_pvt_of_match[] = { 914 { .compatible = "moortec,mr75203" }, 915 { } 916 }; 917 MODULE_DEVICE_TABLE(of, moortec_pvt_of_match); 918 919 static struct platform_driver moortec_pvt_driver = { 920 .driver = { 921 .name = "moortec-pvt", 922 .of_match_table = moortec_pvt_of_match, 923 }, 924 .probe = mr75203_probe, 925 }; 926 module_platform_driver(moortec_pvt_driver); 927 928 MODULE_DESCRIPTION("Moortec Semiconductor MR75203 PVT Controller driver"); 929 MODULE_LICENSE("GPL v2"); 930