1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * HID driver for Nintendo Switch Joy-Cons and Pro Controllers 4 * 5 * Copyright (c) 2019-2021 Daniel J. Ogorchock <djogorchock@gmail.com> 6 * Portions Copyright (c) 2020 Nadia Holmquist Pedersen <nadia@nhp.sh> 7 * Copyright (c) 2022 Emily Strickland <linux@emily.st> 8 * Copyright (c) 2023 Ryan McClelland <rymcclel@gmail.com> 9 * 10 * The following resources/projects were referenced for this driver: 11 * https://github.com/dekuNukem/Nintendo_Switch_Reverse_Engineering 12 * https://gitlab.com/pjranki/joycon-linux-kernel (Peter Rankin) 13 * https://github.com/FrotBot/SwitchProConLinuxUSB 14 * https://github.com/MTCKC/ProconXInput 15 * https://github.com/Davidobot/BetterJoyForCemu 16 * hid-wiimote kernel hid driver 17 * hid-logitech-hidpp driver 18 * hid-sony driver 19 * 20 * This driver supports the Nintendo Switch Joy-Cons and Pro Controllers. The 21 * Pro Controllers can either be used over USB or Bluetooth. 22 * 23 * This driver also incorporates support for Nintendo Switch Online controllers 24 * for the NES, SNES, Sega Genesis, and N64. 25 * 26 * The driver will retrieve the factory calibration info from the controllers, 27 * so little to no user calibration should be required. 28 * 29 */ 30 31 #include "hid-ids.h" 32 #include <asm/unaligned.h> 33 #include <linux/delay.h> 34 #include <linux/device.h> 35 #include <linux/kernel.h> 36 #include <linux/hid.h> 37 #include <linux/idr.h> 38 #include <linux/input.h> 39 #include <linux/jiffies.h> 40 #include <linux/leds.h> 41 #include <linux/module.h> 42 #include <linux/power_supply.h> 43 #include <linux/spinlock.h> 44 45 /* 46 * Reference the url below for the following HID report defines: 47 * https://github.com/dekuNukem/Nintendo_Switch_Reverse_Engineering 48 */ 49 50 /* Output Reports */ 51 #define JC_OUTPUT_RUMBLE_AND_SUBCMD 0x01 52 #define JC_OUTPUT_FW_UPDATE_PKT 0x03 53 #define JC_OUTPUT_RUMBLE_ONLY 0x10 54 #define JC_OUTPUT_MCU_DATA 0x11 55 #define JC_OUTPUT_USB_CMD 0x80 56 57 /* Subcommand IDs */ 58 #define JC_SUBCMD_STATE 0x00 59 #define JC_SUBCMD_MANUAL_BT_PAIRING 0x01 60 #define JC_SUBCMD_REQ_DEV_INFO 0x02 61 #define JC_SUBCMD_SET_REPORT_MODE 0x03 62 #define JC_SUBCMD_TRIGGERS_ELAPSED 0x04 63 #define JC_SUBCMD_GET_PAGE_LIST_STATE 0x05 64 #define JC_SUBCMD_SET_HCI_STATE 0x06 65 #define JC_SUBCMD_RESET_PAIRING_INFO 0x07 66 #define JC_SUBCMD_LOW_POWER_MODE 0x08 67 #define JC_SUBCMD_SPI_FLASH_READ 0x10 68 #define JC_SUBCMD_SPI_FLASH_WRITE 0x11 69 #define JC_SUBCMD_RESET_MCU 0x20 70 #define JC_SUBCMD_SET_MCU_CONFIG 0x21 71 #define JC_SUBCMD_SET_MCU_STATE 0x22 72 #define JC_SUBCMD_SET_PLAYER_LIGHTS 0x30 73 #define JC_SUBCMD_GET_PLAYER_LIGHTS 0x31 74 #define JC_SUBCMD_SET_HOME_LIGHT 0x38 75 #define JC_SUBCMD_ENABLE_IMU 0x40 76 #define JC_SUBCMD_SET_IMU_SENSITIVITY 0x41 77 #define JC_SUBCMD_WRITE_IMU_REG 0x42 78 #define JC_SUBCMD_READ_IMU_REG 0x43 79 #define JC_SUBCMD_ENABLE_VIBRATION 0x48 80 #define JC_SUBCMD_GET_REGULATED_VOLTAGE 0x50 81 82 /* Input Reports */ 83 #define JC_INPUT_BUTTON_EVENT 0x3F 84 #define JC_INPUT_SUBCMD_REPLY 0x21 85 #define JC_INPUT_IMU_DATA 0x30 86 #define JC_INPUT_MCU_DATA 0x31 87 #define JC_INPUT_USB_RESPONSE 0x81 88 89 /* Feature Reports */ 90 #define JC_FEATURE_LAST_SUBCMD 0x02 91 #define JC_FEATURE_OTA_FW_UPGRADE 0x70 92 #define JC_FEATURE_SETUP_MEM_READ 0x71 93 #define JC_FEATURE_MEM_READ 0x72 94 #define JC_FEATURE_ERASE_MEM_SECTOR 0x73 95 #define JC_FEATURE_MEM_WRITE 0x74 96 #define JC_FEATURE_LAUNCH 0x75 97 98 /* USB Commands */ 99 #define JC_USB_CMD_CONN_STATUS 0x01 100 #define JC_USB_CMD_HANDSHAKE 0x02 101 #define JC_USB_CMD_BAUDRATE_3M 0x03 102 #define JC_USB_CMD_NO_TIMEOUT 0x04 103 #define JC_USB_CMD_EN_TIMEOUT 0x05 104 #define JC_USB_RESET 0x06 105 #define JC_USB_PRE_HANDSHAKE 0x91 106 #define JC_USB_SEND_UART 0x92 107 108 /* Magic value denoting presence of user calibration */ 109 #define JC_CAL_USR_MAGIC_0 0xB2 110 #define JC_CAL_USR_MAGIC_1 0xA1 111 #define JC_CAL_USR_MAGIC_SIZE 2 112 113 /* SPI storage addresses of user calibration data */ 114 #define JC_CAL_USR_LEFT_MAGIC_ADDR 0x8010 115 #define JC_CAL_USR_LEFT_DATA_ADDR 0x8012 116 #define JC_CAL_USR_LEFT_DATA_END 0x801A 117 #define JC_CAL_USR_RIGHT_MAGIC_ADDR 0x801B 118 #define JC_CAL_USR_RIGHT_DATA_ADDR 0x801D 119 #define JC_CAL_STICK_DATA_SIZE \ 120 (JC_CAL_USR_LEFT_DATA_END - JC_CAL_USR_LEFT_DATA_ADDR + 1) 121 122 /* SPI storage addresses of factory calibration data */ 123 #define JC_CAL_FCT_DATA_LEFT_ADDR 0x603d 124 #define JC_CAL_FCT_DATA_RIGHT_ADDR 0x6046 125 126 /* SPI storage addresses of IMU factory calibration data */ 127 #define JC_IMU_CAL_FCT_DATA_ADDR 0x6020 128 #define JC_IMU_CAL_FCT_DATA_END 0x6037 129 #define JC_IMU_CAL_DATA_SIZE \ 130 (JC_IMU_CAL_FCT_DATA_END - JC_IMU_CAL_FCT_DATA_ADDR + 1) 131 /* SPI storage addresses of IMU user calibration data */ 132 #define JC_IMU_CAL_USR_MAGIC_ADDR 0x8026 133 #define JC_IMU_CAL_USR_DATA_ADDR 0x8028 134 135 /* The raw analog joystick values will be mapped in terms of this magnitude */ 136 #define JC_MAX_STICK_MAG 32767 137 #define JC_STICK_FUZZ 250 138 #define JC_STICK_FLAT 500 139 140 /* Hat values for pro controller's d-pad */ 141 #define JC_MAX_DPAD_MAG 1 142 #define JC_DPAD_FUZZ 0 143 #define JC_DPAD_FLAT 0 144 145 /* Under most circumstances IMU reports are pushed every 15ms; use as default */ 146 #define JC_IMU_DFLT_AVG_DELTA_MS 15 147 /* How many samples to sum before calculating average IMU report delta */ 148 #define JC_IMU_SAMPLES_PER_DELTA_AVG 300 149 /* Controls how many dropped IMU packets at once trigger a warning message */ 150 #define JC_IMU_DROPPED_PKT_WARNING 3 151 152 /* 153 * The controller's accelerometer has a sensor resolution of 16bits and is 154 * configured with a range of +-8000 milliGs. Therefore, the resolution can be 155 * calculated thus: (2^16-1)/(8000 * 2) = 4.096 digits per milliG 156 * Resolution per G (rather than per millliG): 4.096 * 1000 = 4096 digits per G 157 * Alternatively: 1/4096 = .0002441 Gs per digit 158 */ 159 #define JC_IMU_MAX_ACCEL_MAG 32767 160 #define JC_IMU_ACCEL_RES_PER_G 4096 161 #define JC_IMU_ACCEL_FUZZ 10 162 #define JC_IMU_ACCEL_FLAT 0 163 164 /* 165 * The controller's gyroscope has a sensor resolution of 16bits and is 166 * configured with a range of +-2000 degrees/second. 167 * Digits per dps: (2^16 -1)/(2000*2) = 16.38375 168 * dps per digit: 16.38375E-1 = .0610 169 * 170 * STMicro recommends in the datasheet to add 15% to the dps/digit. This allows 171 * the full sensitivity range to be saturated without clipping. This yields more 172 * accurate results, so it's the technique this driver uses. 173 * dps per digit (corrected): .0610 * 1.15 = .0702 174 * digits per dps (corrected): .0702E-1 = 14.247 175 * 176 * Now, 14.247 truncating to 14 loses a lot of precision, so we rescale the 177 * min/max range by 1000. 178 */ 179 #define JC_IMU_PREC_RANGE_SCALE 1000 180 /* Note: change mag and res_per_dps if prec_range_scale is ever altered */ 181 #define JC_IMU_MAX_GYRO_MAG 32767000 /* (2^16-1)*1000 */ 182 #define JC_IMU_GYRO_RES_PER_DPS 14247 /* (14.247*1000) */ 183 #define JC_IMU_GYRO_FUZZ 10 184 #define JC_IMU_GYRO_FLAT 0 185 186 /* frequency/amplitude tables for rumble */ 187 struct joycon_rumble_freq_data { 188 u16 high; 189 u8 low; 190 u16 freq; /* Hz*/ 191 }; 192 193 struct joycon_rumble_amp_data { 194 u8 high; 195 u16 low; 196 u16 amp; 197 }; 198 199 #if IS_ENABLED(CONFIG_NINTENDO_FF) 200 /* 201 * These tables are from 202 * https://github.com/dekuNukem/Nintendo_Switch_Reverse_Engineering/blob/master/rumble_data_table.md 203 */ 204 static const struct joycon_rumble_freq_data joycon_rumble_frequencies[] = { 205 /* high, low, freq */ 206 { 0x0000, 0x01, 41 }, { 0x0000, 0x02, 42 }, { 0x0000, 0x03, 43 }, 207 { 0x0000, 0x04, 44 }, { 0x0000, 0x05, 45 }, { 0x0000, 0x06, 46 }, 208 { 0x0000, 0x07, 47 }, { 0x0000, 0x08, 48 }, { 0x0000, 0x09, 49 }, 209 { 0x0000, 0x0A, 50 }, { 0x0000, 0x0B, 51 }, { 0x0000, 0x0C, 52 }, 210 { 0x0000, 0x0D, 53 }, { 0x0000, 0x0E, 54 }, { 0x0000, 0x0F, 55 }, 211 { 0x0000, 0x10, 57 }, { 0x0000, 0x11, 58 }, { 0x0000, 0x12, 59 }, 212 { 0x0000, 0x13, 60 }, { 0x0000, 0x14, 62 }, { 0x0000, 0x15, 63 }, 213 { 0x0000, 0x16, 64 }, { 0x0000, 0x17, 66 }, { 0x0000, 0x18, 67 }, 214 { 0x0000, 0x19, 69 }, { 0x0000, 0x1A, 70 }, { 0x0000, 0x1B, 72 }, 215 { 0x0000, 0x1C, 73 }, { 0x0000, 0x1D, 75 }, { 0x0000, 0x1e, 77 }, 216 { 0x0000, 0x1f, 78 }, { 0x0000, 0x20, 80 }, { 0x0400, 0x21, 82 }, 217 { 0x0800, 0x22, 84 }, { 0x0c00, 0x23, 85 }, { 0x1000, 0x24, 87 }, 218 { 0x1400, 0x25, 89 }, { 0x1800, 0x26, 91 }, { 0x1c00, 0x27, 93 }, 219 { 0x2000, 0x28, 95 }, { 0x2400, 0x29, 97 }, { 0x2800, 0x2a, 99 }, 220 { 0x2c00, 0x2b, 102 }, { 0x3000, 0x2c, 104 }, { 0x3400, 0x2d, 106 }, 221 { 0x3800, 0x2e, 108 }, { 0x3c00, 0x2f, 111 }, { 0x4000, 0x30, 113 }, 222 { 0x4400, 0x31, 116 }, { 0x4800, 0x32, 118 }, { 0x4c00, 0x33, 121 }, 223 { 0x5000, 0x34, 123 }, { 0x5400, 0x35, 126 }, { 0x5800, 0x36, 129 }, 224 { 0x5c00, 0x37, 132 }, { 0x6000, 0x38, 135 }, { 0x6400, 0x39, 137 }, 225 { 0x6800, 0x3a, 141 }, { 0x6c00, 0x3b, 144 }, { 0x7000, 0x3c, 147 }, 226 { 0x7400, 0x3d, 150 }, { 0x7800, 0x3e, 153 }, { 0x7c00, 0x3f, 157 }, 227 { 0x8000, 0x40, 160 }, { 0x8400, 0x41, 164 }, { 0x8800, 0x42, 167 }, 228 { 0x8c00, 0x43, 171 }, { 0x9000, 0x44, 174 }, { 0x9400, 0x45, 178 }, 229 { 0x9800, 0x46, 182 }, { 0x9c00, 0x47, 186 }, { 0xa000, 0x48, 190 }, 230 { 0xa400, 0x49, 194 }, { 0xa800, 0x4a, 199 }, { 0xac00, 0x4b, 203 }, 231 { 0xb000, 0x4c, 207 }, { 0xb400, 0x4d, 212 }, { 0xb800, 0x4e, 217 }, 232 { 0xbc00, 0x4f, 221 }, { 0xc000, 0x50, 226 }, { 0xc400, 0x51, 231 }, 233 { 0xc800, 0x52, 236 }, { 0xcc00, 0x53, 241 }, { 0xd000, 0x54, 247 }, 234 { 0xd400, 0x55, 252 }, { 0xd800, 0x56, 258 }, { 0xdc00, 0x57, 263 }, 235 { 0xe000, 0x58, 269 }, { 0xe400, 0x59, 275 }, { 0xe800, 0x5a, 281 }, 236 { 0xec00, 0x5b, 287 }, { 0xf000, 0x5c, 293 }, { 0xf400, 0x5d, 300 }, 237 { 0xf800, 0x5e, 306 }, { 0xfc00, 0x5f, 313 }, { 0x0001, 0x60, 320 }, 238 { 0x0401, 0x61, 327 }, { 0x0801, 0x62, 334 }, { 0x0c01, 0x63, 341 }, 239 { 0x1001, 0x64, 349 }, { 0x1401, 0x65, 357 }, { 0x1801, 0x66, 364 }, 240 { 0x1c01, 0x67, 372 }, { 0x2001, 0x68, 381 }, { 0x2401, 0x69, 389 }, 241 { 0x2801, 0x6a, 397 }, { 0x2c01, 0x6b, 406 }, { 0x3001, 0x6c, 415 }, 242 { 0x3401, 0x6d, 424 }, { 0x3801, 0x6e, 433 }, { 0x3c01, 0x6f, 443 }, 243 { 0x4001, 0x70, 453 }, { 0x4401, 0x71, 462 }, { 0x4801, 0x72, 473 }, 244 { 0x4c01, 0x73, 483 }, { 0x5001, 0x74, 494 }, { 0x5401, 0x75, 504 }, 245 { 0x5801, 0x76, 515 }, { 0x5c01, 0x77, 527 }, { 0x6001, 0x78, 538 }, 246 { 0x6401, 0x79, 550 }, { 0x6801, 0x7a, 562 }, { 0x6c01, 0x7b, 574 }, 247 { 0x7001, 0x7c, 587 }, { 0x7401, 0x7d, 600 }, { 0x7801, 0x7e, 613 }, 248 { 0x7c01, 0x7f, 626 }, { 0x8001, 0x00, 640 }, { 0x8401, 0x00, 654 }, 249 { 0x8801, 0x00, 668 }, { 0x8c01, 0x00, 683 }, { 0x9001, 0x00, 698 }, 250 { 0x9401, 0x00, 713 }, { 0x9801, 0x00, 729 }, { 0x9c01, 0x00, 745 }, 251 { 0xa001, 0x00, 761 }, { 0xa401, 0x00, 778 }, { 0xa801, 0x00, 795 }, 252 { 0xac01, 0x00, 812 }, { 0xb001, 0x00, 830 }, { 0xb401, 0x00, 848 }, 253 { 0xb801, 0x00, 867 }, { 0xbc01, 0x00, 886 }, { 0xc001, 0x00, 905 }, 254 { 0xc401, 0x00, 925 }, { 0xc801, 0x00, 945 }, { 0xcc01, 0x00, 966 }, 255 { 0xd001, 0x00, 987 }, { 0xd401, 0x00, 1009 }, { 0xd801, 0x00, 1031 }, 256 { 0xdc01, 0x00, 1053 }, { 0xe001, 0x00, 1076 }, { 0xe401, 0x00, 1100 }, 257 { 0xe801, 0x00, 1124 }, { 0xec01, 0x00, 1149 }, { 0xf001, 0x00, 1174 }, 258 { 0xf401, 0x00, 1199 }, { 0xf801, 0x00, 1226 }, { 0xfc01, 0x00, 1253 } 259 }; 260 261 #define joycon_max_rumble_amp (1003) 262 static const struct joycon_rumble_amp_data joycon_rumble_amplitudes[] = { 263 /* high, low, amp */ 264 { 0x00, 0x0040, 0 }, 265 { 0x02, 0x8040, 10 }, { 0x04, 0x0041, 12 }, { 0x06, 0x8041, 14 }, 266 { 0x08, 0x0042, 17 }, { 0x0a, 0x8042, 20 }, { 0x0c, 0x0043, 24 }, 267 { 0x0e, 0x8043, 28 }, { 0x10, 0x0044, 33 }, { 0x12, 0x8044, 40 }, 268 { 0x14, 0x0045, 47 }, { 0x16, 0x8045, 56 }, { 0x18, 0x0046, 67 }, 269 { 0x1a, 0x8046, 80 }, { 0x1c, 0x0047, 95 }, { 0x1e, 0x8047, 112 }, 270 { 0x20, 0x0048, 117 }, { 0x22, 0x8048, 123 }, { 0x24, 0x0049, 128 }, 271 { 0x26, 0x8049, 134 }, { 0x28, 0x004a, 140 }, { 0x2a, 0x804a, 146 }, 272 { 0x2c, 0x004b, 152 }, { 0x2e, 0x804b, 159 }, { 0x30, 0x004c, 166 }, 273 { 0x32, 0x804c, 173 }, { 0x34, 0x004d, 181 }, { 0x36, 0x804d, 189 }, 274 { 0x38, 0x004e, 198 }, { 0x3a, 0x804e, 206 }, { 0x3c, 0x004f, 215 }, 275 { 0x3e, 0x804f, 225 }, { 0x40, 0x0050, 230 }, { 0x42, 0x8050, 235 }, 276 { 0x44, 0x0051, 240 }, { 0x46, 0x8051, 245 }, { 0x48, 0x0052, 251 }, 277 { 0x4a, 0x8052, 256 }, { 0x4c, 0x0053, 262 }, { 0x4e, 0x8053, 268 }, 278 { 0x50, 0x0054, 273 }, { 0x52, 0x8054, 279 }, { 0x54, 0x0055, 286 }, 279 { 0x56, 0x8055, 292 }, { 0x58, 0x0056, 298 }, { 0x5a, 0x8056, 305 }, 280 { 0x5c, 0x0057, 311 }, { 0x5e, 0x8057, 318 }, { 0x60, 0x0058, 325 }, 281 { 0x62, 0x8058, 332 }, { 0x64, 0x0059, 340 }, { 0x66, 0x8059, 347 }, 282 { 0x68, 0x005a, 355 }, { 0x6a, 0x805a, 362 }, { 0x6c, 0x005b, 370 }, 283 { 0x6e, 0x805b, 378 }, { 0x70, 0x005c, 387 }, { 0x72, 0x805c, 395 }, 284 { 0x74, 0x005d, 404 }, { 0x76, 0x805d, 413 }, { 0x78, 0x005e, 422 }, 285 { 0x7a, 0x805e, 431 }, { 0x7c, 0x005f, 440 }, { 0x7e, 0x805f, 450 }, 286 { 0x80, 0x0060, 460 }, { 0x82, 0x8060, 470 }, { 0x84, 0x0061, 480 }, 287 { 0x86, 0x8061, 491 }, { 0x88, 0x0062, 501 }, { 0x8a, 0x8062, 512 }, 288 { 0x8c, 0x0063, 524 }, { 0x8e, 0x8063, 535 }, { 0x90, 0x0064, 547 }, 289 { 0x92, 0x8064, 559 }, { 0x94, 0x0065, 571 }, { 0x96, 0x8065, 584 }, 290 { 0x98, 0x0066, 596 }, { 0x9a, 0x8066, 609 }, { 0x9c, 0x0067, 623 }, 291 { 0x9e, 0x8067, 636 }, { 0xa0, 0x0068, 650 }, { 0xa2, 0x8068, 665 }, 292 { 0xa4, 0x0069, 679 }, { 0xa6, 0x8069, 694 }, { 0xa8, 0x006a, 709 }, 293 { 0xaa, 0x806a, 725 }, { 0xac, 0x006b, 741 }, { 0xae, 0x806b, 757 }, 294 { 0xb0, 0x006c, 773 }, { 0xb2, 0x806c, 790 }, { 0xb4, 0x006d, 808 }, 295 { 0xb6, 0x806d, 825 }, { 0xb8, 0x006e, 843 }, { 0xba, 0x806e, 862 }, 296 { 0xbc, 0x006f, 881 }, { 0xbe, 0x806f, 900 }, { 0xc0, 0x0070, 920 }, 297 { 0xc2, 0x8070, 940 }, { 0xc4, 0x0071, 960 }, { 0xc6, 0x8071, 981 }, 298 { 0xc8, 0x0072, joycon_max_rumble_amp } 299 }; 300 static const u16 JC_RUMBLE_DFLT_LOW_FREQ = 160; 301 static const u16 JC_RUMBLE_DFLT_HIGH_FREQ = 320; 302 static const unsigned short JC_RUMBLE_ZERO_AMP_PKT_CNT = 5; 303 #endif /* IS_ENABLED(CONFIG_NINTENDO_FF) */ 304 static const u16 JC_RUMBLE_PERIOD_MS = 50; 305 306 /* States for controller state machine */ 307 enum joycon_ctlr_state { 308 JOYCON_CTLR_STATE_INIT, 309 JOYCON_CTLR_STATE_READ, 310 JOYCON_CTLR_STATE_REMOVED, 311 }; 312 313 /* Controller type received as part of device info */ 314 enum joycon_ctlr_type { 315 JOYCON_CTLR_TYPE_JCL = 0x01, 316 JOYCON_CTLR_TYPE_JCR = 0x02, 317 JOYCON_CTLR_TYPE_PRO = 0x03, 318 JOYCON_CTLR_TYPE_NESL = 0x09, 319 JOYCON_CTLR_TYPE_NESR = 0x0A, 320 JOYCON_CTLR_TYPE_SNES = 0x0B, 321 JOYCON_CTLR_TYPE_GEN = 0x0D, 322 JOYCON_CTLR_TYPE_N64 = 0x0C, 323 }; 324 325 struct joycon_stick_cal { 326 s32 max; 327 s32 min; 328 s32 center; 329 }; 330 331 struct joycon_imu_cal { 332 s16 offset[3]; 333 s16 scale[3]; 334 }; 335 336 /* 337 * All the controller's button values are stored in a u32. 338 * They can be accessed with bitwise ANDs. 339 */ 340 #define JC_BTN_Y BIT(0) 341 #define JC_BTN_X BIT(1) 342 #define JC_BTN_B BIT(2) 343 #define JC_BTN_A BIT(3) 344 #define JC_BTN_SR_R BIT(4) 345 #define JC_BTN_SL_R BIT(5) 346 #define JC_BTN_R BIT(6) 347 #define JC_BTN_ZR BIT(7) 348 #define JC_BTN_MINUS BIT(8) 349 #define JC_BTN_PLUS BIT(9) 350 #define JC_BTN_RSTICK BIT(10) 351 #define JC_BTN_LSTICK BIT(11) 352 #define JC_BTN_HOME BIT(12) 353 #define JC_BTN_CAP BIT(13) /* capture button */ 354 #define JC_BTN_DOWN BIT(16) 355 #define JC_BTN_UP BIT(17) 356 #define JC_BTN_RIGHT BIT(18) 357 #define JC_BTN_LEFT BIT(19) 358 #define JC_BTN_SR_L BIT(20) 359 #define JC_BTN_SL_L BIT(21) 360 #define JC_BTN_L BIT(22) 361 #define JC_BTN_ZL BIT(23) 362 363 struct joycon_ctlr_button_mapping { 364 u32 code; 365 u32 bit; 366 }; 367 368 /* 369 * D-pad is configured as buttons for the left Joy-Con only! 370 */ 371 static const struct joycon_ctlr_button_mapping left_joycon_button_mappings[] = { 372 { BTN_TL, JC_BTN_L, }, 373 { BTN_TL2, JC_BTN_ZL, }, 374 { BTN_SELECT, JC_BTN_MINUS, }, 375 { BTN_THUMBL, JC_BTN_LSTICK, }, 376 { BTN_DPAD_UP, JC_BTN_UP, }, 377 { BTN_DPAD_DOWN, JC_BTN_DOWN, }, 378 { BTN_DPAD_LEFT, JC_BTN_LEFT, }, 379 { BTN_DPAD_RIGHT, JC_BTN_RIGHT, }, 380 { BTN_Z, JC_BTN_CAP, }, 381 { /* sentinel */ }, 382 }; 383 384 /* 385 * The unused *right*-side triggers become the SL/SR triggers for the *left* 386 * Joy-Con, if and only if we're not using a charging grip. 387 */ 388 static const struct joycon_ctlr_button_mapping left_joycon_s_button_mappings[] = { 389 { BTN_TR, JC_BTN_SL_L, }, 390 { BTN_TR2, JC_BTN_SR_L, }, 391 { /* sentinel */ }, 392 }; 393 394 static const struct joycon_ctlr_button_mapping right_joycon_button_mappings[] = { 395 { BTN_EAST, JC_BTN_A, }, 396 { BTN_SOUTH, JC_BTN_B, }, 397 { BTN_NORTH, JC_BTN_X, }, 398 { BTN_WEST, JC_BTN_Y, }, 399 { BTN_TR, JC_BTN_R, }, 400 { BTN_TR2, JC_BTN_ZR, }, 401 { BTN_START, JC_BTN_PLUS, }, 402 { BTN_THUMBR, JC_BTN_RSTICK, }, 403 { BTN_MODE, JC_BTN_HOME, }, 404 { /* sentinel */ }, 405 }; 406 407 /* 408 * The unused *left*-side triggers become the SL/SR triggers for the *right* 409 * Joy-Con, if and only if we're not using a charging grip. 410 */ 411 static const struct joycon_ctlr_button_mapping right_joycon_s_button_mappings[] = { 412 { BTN_TL, JC_BTN_SL_R, }, 413 { BTN_TL2, JC_BTN_SR_R, }, 414 { /* sentinel */ }, 415 }; 416 417 static const struct joycon_ctlr_button_mapping procon_button_mappings[] = { 418 { BTN_EAST, JC_BTN_A, }, 419 { BTN_SOUTH, JC_BTN_B, }, 420 { BTN_NORTH, JC_BTN_X, }, 421 { BTN_WEST, JC_BTN_Y, }, 422 { BTN_TL, JC_BTN_L, }, 423 { BTN_TR, JC_BTN_R, }, 424 { BTN_TL2, JC_BTN_ZL, }, 425 { BTN_TR2, JC_BTN_ZR, }, 426 { BTN_SELECT, JC_BTN_MINUS, }, 427 { BTN_START, JC_BTN_PLUS, }, 428 { BTN_THUMBL, JC_BTN_LSTICK, }, 429 { BTN_THUMBR, JC_BTN_RSTICK, }, 430 { BTN_MODE, JC_BTN_HOME, }, 431 { BTN_Z, JC_BTN_CAP, }, 432 { /* sentinel */ }, 433 }; 434 435 static const struct joycon_ctlr_button_mapping nescon_button_mappings[] = { 436 { BTN_SOUTH, JC_BTN_A, }, 437 { BTN_EAST, JC_BTN_B, }, 438 { BTN_TL, JC_BTN_L, }, 439 { BTN_TR, JC_BTN_R, }, 440 { BTN_SELECT, JC_BTN_MINUS, }, 441 { BTN_START, JC_BTN_PLUS, }, 442 { /* sentinel */ }, 443 }; 444 445 static const struct joycon_ctlr_button_mapping snescon_button_mappings[] = { 446 { BTN_EAST, JC_BTN_A, }, 447 { BTN_SOUTH, JC_BTN_B, }, 448 { BTN_NORTH, JC_BTN_X, }, 449 { BTN_WEST, JC_BTN_Y, }, 450 { BTN_TL, JC_BTN_L, }, 451 { BTN_TR, JC_BTN_R, }, 452 { BTN_TL2, JC_BTN_ZL, }, 453 { BTN_TR2, JC_BTN_ZR, }, 454 { BTN_SELECT, JC_BTN_MINUS, }, 455 { BTN_START, JC_BTN_PLUS, }, 456 { /* sentinel */ }, 457 }; 458 459 /* 460 * "A", "B", and "C" are mapped positionally, rather than by label (e.g., "A" 461 * gets assigned to BTN_EAST instead of BTN_A). 462 */ 463 static const struct joycon_ctlr_button_mapping gencon_button_mappings[] = { 464 { BTN_SOUTH, JC_BTN_A, }, 465 { BTN_EAST, JC_BTN_B, }, 466 { BTN_WEST, JC_BTN_R, }, 467 { BTN_SELECT, JC_BTN_ZR, }, 468 { BTN_START, JC_BTN_PLUS, }, 469 { BTN_MODE, JC_BTN_HOME, }, 470 { BTN_Z, JC_BTN_CAP, }, 471 { /* sentinel */ }, 472 }; 473 474 /* 475 * N64's C buttons get assigned to d-pad directions and registered as buttons. 476 */ 477 static const struct joycon_ctlr_button_mapping n64con_button_mappings[] = { 478 { BTN_A, JC_BTN_A, }, 479 { BTN_B, JC_BTN_B, }, 480 { BTN_TL2, JC_BTN_ZL, }, /* Z */ 481 { BTN_TL, JC_BTN_L, }, 482 { BTN_TR, JC_BTN_R, }, 483 { BTN_TR2, JC_BTN_LSTICK, }, /* ZR */ 484 { BTN_START, JC_BTN_PLUS, }, 485 { BTN_SELECT, JC_BTN_Y, }, /* C UP */ 486 { BTN_X, JC_BTN_ZR, }, /* C DOWN */ 487 { BTN_Y, JC_BTN_X, }, /* C LEFT */ 488 { BTN_C, JC_BTN_MINUS, }, /* C RIGHT */ 489 { BTN_MODE, JC_BTN_HOME, }, 490 { BTN_Z, JC_BTN_CAP, }, 491 { /* sentinel */ }, 492 }; 493 494 enum joycon_msg_type { 495 JOYCON_MSG_TYPE_NONE, 496 JOYCON_MSG_TYPE_USB, 497 JOYCON_MSG_TYPE_SUBCMD, 498 }; 499 500 struct joycon_rumble_output { 501 u8 output_id; 502 u8 packet_num; 503 u8 rumble_data[8]; 504 } __packed; 505 506 struct joycon_subcmd_request { 507 u8 output_id; /* must be 0x01 for subcommand, 0x10 for rumble only */ 508 u8 packet_num; /* incremented every send */ 509 u8 rumble_data[8]; 510 u8 subcmd_id; 511 u8 data[]; /* length depends on the subcommand */ 512 } __packed; 513 514 struct joycon_subcmd_reply { 515 u8 ack; /* MSB 1 for ACK, 0 for NACK */ 516 u8 id; /* id of requested subcmd */ 517 u8 data[]; /* will be at most 35 bytes */ 518 } __packed; 519 520 struct joycon_imu_data { 521 s16 accel_x; 522 s16 accel_y; 523 s16 accel_z; 524 s16 gyro_x; 525 s16 gyro_y; 526 s16 gyro_z; 527 } __packed; 528 529 struct joycon_input_report { 530 u8 id; 531 u8 timer; 532 u8 bat_con; /* battery and connection info */ 533 u8 button_status[3]; 534 u8 left_stick[3]; 535 u8 right_stick[3]; 536 u8 vibrator_report; 537 538 union { 539 struct joycon_subcmd_reply subcmd_reply; 540 /* IMU input reports contain 3 samples */ 541 u8 imu_raw_bytes[sizeof(struct joycon_imu_data) * 3]; 542 }; 543 } __packed; 544 545 #define JC_MAX_RESP_SIZE (sizeof(struct joycon_input_report) + 35) 546 #define JC_RUMBLE_DATA_SIZE 8 547 #define JC_RUMBLE_QUEUE_SIZE 8 548 549 static const char * const joycon_player_led_names[] = { 550 LED_FUNCTION_PLAYER1, 551 LED_FUNCTION_PLAYER2, 552 LED_FUNCTION_PLAYER3, 553 LED_FUNCTION_PLAYER4, 554 }; 555 #define JC_NUM_LEDS ARRAY_SIZE(joycon_player_led_names) 556 #define JC_NUM_LED_PATTERNS 8 557 /* Taken from https://www.nintendo.com/my/support/qa/detail/33822 */ 558 static const enum led_brightness joycon_player_led_patterns[JC_NUM_LED_PATTERNS][JC_NUM_LEDS] = { 559 { 1, 0, 0, 0 }, 560 { 1, 1, 0, 0 }, 561 { 1, 1, 1, 0 }, 562 { 1, 1, 1, 1 }, 563 { 1, 0, 0, 1 }, 564 { 1, 0, 1, 0 }, 565 { 1, 0, 1, 1 }, 566 { 0, 1, 1, 0 }, 567 }; 568 569 /* Each physical controller is associated with a joycon_ctlr struct */ 570 struct joycon_ctlr { 571 struct hid_device *hdev; 572 struct input_dev *input; 573 u32 player_id; 574 struct led_classdev leds[JC_NUM_LEDS]; /* player leds */ 575 struct led_classdev home_led; 576 enum joycon_ctlr_state ctlr_state; 577 spinlock_t lock; 578 u8 mac_addr[6]; 579 char *mac_addr_str; 580 enum joycon_ctlr_type ctlr_type; 581 582 /* The following members are used for synchronous sends/receives */ 583 enum joycon_msg_type msg_type; 584 u8 subcmd_num; 585 struct mutex output_mutex; 586 u8 input_buf[JC_MAX_RESP_SIZE]; 587 wait_queue_head_t wait; 588 bool received_resp; 589 u8 usb_ack_match; 590 u8 subcmd_ack_match; 591 bool received_input_report; 592 unsigned int last_input_report_msecs; 593 unsigned int last_subcmd_sent_msecs; 594 unsigned int consecutive_valid_report_deltas; 595 596 /* factory calibration data */ 597 struct joycon_stick_cal left_stick_cal_x; 598 struct joycon_stick_cal left_stick_cal_y; 599 struct joycon_stick_cal right_stick_cal_x; 600 struct joycon_stick_cal right_stick_cal_y; 601 602 struct joycon_imu_cal accel_cal; 603 struct joycon_imu_cal gyro_cal; 604 605 /* prevents needlessly recalculating these divisors every sample */ 606 s32 imu_cal_accel_divisor[3]; 607 s32 imu_cal_gyro_divisor[3]; 608 609 /* power supply data */ 610 struct power_supply *battery; 611 struct power_supply_desc battery_desc; 612 u8 battery_capacity; 613 bool battery_charging; 614 bool host_powered; 615 616 /* rumble */ 617 u8 rumble_data[JC_RUMBLE_QUEUE_SIZE][JC_RUMBLE_DATA_SIZE]; 618 int rumble_queue_head; 619 int rumble_queue_tail; 620 struct workqueue_struct *rumble_queue; 621 struct work_struct rumble_worker; 622 unsigned int rumble_msecs; 623 u16 rumble_ll_freq; 624 u16 rumble_lh_freq; 625 u16 rumble_rl_freq; 626 u16 rumble_rh_freq; 627 unsigned short rumble_zero_countdown; 628 629 /* imu */ 630 struct input_dev *imu_input; 631 bool imu_first_packet_received; /* helps in initiating timestamp */ 632 unsigned int imu_timestamp_us; /* timestamp we report to userspace */ 633 unsigned int imu_last_pkt_ms; /* used to calc imu report delta */ 634 /* the following are used to track the average imu report time delta */ 635 unsigned int imu_delta_samples_count; 636 unsigned int imu_delta_samples_sum; 637 unsigned int imu_avg_delta_ms; 638 }; 639 640 /* Helper macros for checking controller type */ 641 #define jc_type_is_joycon(ctlr) \ 642 (ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_JOYCONL || \ 643 ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_JOYCONR || \ 644 ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_CHRGGRIP) 645 #define jc_type_is_procon(ctlr) \ 646 (ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_PROCON) 647 #define jc_type_is_chrggrip(ctlr) \ 648 (ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_CHRGGRIP) 649 650 /* Does this controller have inputs associated with left joycon? */ 651 #define jc_type_has_left(ctlr) \ 652 (ctlr->ctlr_type == JOYCON_CTLR_TYPE_JCL || \ 653 ctlr->ctlr_type == JOYCON_CTLR_TYPE_PRO || \ 654 ctlr->ctlr_type == JOYCON_CTLR_TYPE_N64) 655 656 /* Does this controller have inputs associated with right joycon? */ 657 #define jc_type_has_right(ctlr) \ 658 (ctlr->ctlr_type == JOYCON_CTLR_TYPE_JCR || \ 659 ctlr->ctlr_type == JOYCON_CTLR_TYPE_PRO) 660 661 /* 662 * Controller device helpers 663 * 664 * These look at the device ID known to the HID subsystem to identify a device, 665 * but take caution: some NSO devices lie about themselves (NES Joy-Cons and 666 * Sega Genesis controller). See type helpers below. 667 * 668 * These helpers are most useful early during the HID probe or in conjunction 669 * with the capability helpers below. 670 */ 671 static inline bool joycon_device_is_chrggrip(struct joycon_ctlr *ctlr) 672 { 673 return ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_CHRGGRIP; 674 } 675 676 /* 677 * Controller type helpers 678 * 679 * These are slightly different than the device-ID-based helpers above. They are 680 * generally more reliable, since they can distinguish between, e.g., Genesis 681 * versus SNES, or NES Joy-Cons versus regular Switch Joy-Cons. They're most 682 * useful for reporting available inputs. For other kinds of distinctions, see 683 * the capability helpers below. 684 * 685 * They have two major drawbacks: (1) they're not available until after we set 686 * the reporting method and then request the device info; (2) they can't 687 * distinguish all controllers (like the Charging Grip from the Pro controller.) 688 */ 689 static inline bool joycon_type_is_left_joycon(struct joycon_ctlr *ctlr) 690 { 691 return ctlr->ctlr_type == JOYCON_CTLR_TYPE_JCL; 692 } 693 694 static inline bool joycon_type_is_right_joycon(struct joycon_ctlr *ctlr) 695 { 696 return ctlr->ctlr_type == JOYCON_CTLR_TYPE_JCR; 697 } 698 699 static inline bool joycon_type_is_procon(struct joycon_ctlr *ctlr) 700 { 701 return ctlr->ctlr_type == JOYCON_CTLR_TYPE_PRO; 702 } 703 704 static inline bool joycon_type_is_snescon(struct joycon_ctlr *ctlr) 705 { 706 return ctlr->ctlr_type == JOYCON_CTLR_TYPE_SNES; 707 } 708 709 static inline bool joycon_type_is_gencon(struct joycon_ctlr *ctlr) 710 { 711 return ctlr->ctlr_type == JOYCON_CTLR_TYPE_GEN; 712 } 713 714 static inline bool joycon_type_is_n64con(struct joycon_ctlr *ctlr) 715 { 716 return ctlr->ctlr_type == JOYCON_CTLR_TYPE_N64; 717 } 718 719 static inline bool joycon_type_is_left_nescon(struct joycon_ctlr *ctlr) 720 { 721 return ctlr->ctlr_type == JOYCON_CTLR_TYPE_NESL; 722 } 723 724 static inline bool joycon_type_is_right_nescon(struct joycon_ctlr *ctlr) 725 { 726 return ctlr->ctlr_type == JOYCON_CTLR_TYPE_NESR; 727 } 728 729 static inline bool joycon_type_is_any_joycon(struct joycon_ctlr *ctlr) 730 { 731 return joycon_type_is_left_joycon(ctlr) || 732 joycon_type_is_right_joycon(ctlr) || 733 joycon_device_is_chrggrip(ctlr); 734 } 735 736 static inline bool joycon_type_is_any_nescon(struct joycon_ctlr *ctlr) 737 { 738 return joycon_type_is_left_nescon(ctlr) || 739 joycon_type_is_right_nescon(ctlr); 740 } 741 742 /* 743 * Controller capability helpers 744 * 745 * These helpers combine the use of the helpers above to detect certain 746 * capabilities during initialization. They are always accurate but (since they 747 * use type helpers) cannot be used early in the HID probe. 748 */ 749 static inline bool joycon_has_imu(struct joycon_ctlr *ctlr) 750 { 751 return joycon_device_is_chrggrip(ctlr) || 752 joycon_type_is_any_joycon(ctlr) || 753 joycon_type_is_procon(ctlr); 754 } 755 756 static inline bool joycon_has_joysticks(struct joycon_ctlr *ctlr) 757 { 758 return joycon_device_is_chrggrip(ctlr) || 759 joycon_type_is_any_joycon(ctlr) || 760 joycon_type_is_procon(ctlr) || 761 joycon_type_is_n64con(ctlr); 762 } 763 764 static inline bool joycon_has_rumble(struct joycon_ctlr *ctlr) 765 { 766 return joycon_device_is_chrggrip(ctlr) || 767 joycon_type_is_any_joycon(ctlr) || 768 joycon_type_is_procon(ctlr) || 769 joycon_type_is_n64con(ctlr); 770 } 771 772 static inline bool joycon_using_usb(struct joycon_ctlr *ctlr) 773 { 774 return ctlr->hdev->bus == BUS_USB; 775 } 776 777 static int __joycon_hid_send(struct hid_device *hdev, u8 *data, size_t len) 778 { 779 u8 *buf; 780 int ret; 781 782 buf = kmemdup(data, len, GFP_KERNEL); 783 if (!buf) 784 return -ENOMEM; 785 ret = hid_hw_output_report(hdev, buf, len); 786 kfree(buf); 787 if (ret < 0) 788 hid_dbg(hdev, "Failed to send output report ret=%d\n", ret); 789 return ret; 790 } 791 792 static void joycon_wait_for_input_report(struct joycon_ctlr *ctlr) 793 { 794 int ret; 795 796 /* 797 * If we are in the proper reporting mode, wait for an input 798 * report prior to sending the subcommand. This improves 799 * reliability considerably. 800 */ 801 if (ctlr->ctlr_state == JOYCON_CTLR_STATE_READ) { 802 unsigned long flags; 803 804 spin_lock_irqsave(&ctlr->lock, flags); 805 ctlr->received_input_report = false; 806 spin_unlock_irqrestore(&ctlr->lock, flags); 807 ret = wait_event_timeout(ctlr->wait, 808 ctlr->received_input_report, 809 HZ / 4); 810 /* We will still proceed, even with a timeout here */ 811 if (!ret) 812 hid_warn(ctlr->hdev, 813 "timeout waiting for input report\n"); 814 } 815 } 816 817 /* 818 * Sending subcommands and/or rumble data at too high a rate can cause bluetooth 819 * controller disconnections. 820 */ 821 #define JC_INPUT_REPORT_MIN_DELTA 8 822 #define JC_INPUT_REPORT_MAX_DELTA 17 823 #define JC_SUBCMD_TX_OFFSET_MS 4 824 #define JC_SUBCMD_VALID_DELTA_REQ 3 825 #define JC_SUBCMD_RATE_MAX_ATTEMPTS 500 826 #define JC_SUBCMD_RATE_LIMITER_USB_MS 20 827 #define JC_SUBCMD_RATE_LIMITER_BT_MS 60 828 #define JC_SUBCMD_RATE_LIMITER_MS(ctlr) ((ctlr)->hdev->bus == BUS_USB ? JC_SUBCMD_RATE_LIMITER_USB_MS : JC_SUBCMD_RATE_LIMITER_BT_MS) 829 static void joycon_enforce_subcmd_rate(struct joycon_ctlr *ctlr) 830 { 831 unsigned int current_ms; 832 unsigned long subcmd_delta; 833 int consecutive_valid_deltas = 0; 834 int attempts = 0; 835 unsigned long flags; 836 837 if (unlikely(ctlr->ctlr_state != JOYCON_CTLR_STATE_READ)) 838 return; 839 840 do { 841 joycon_wait_for_input_report(ctlr); 842 current_ms = jiffies_to_msecs(jiffies); 843 subcmd_delta = current_ms - ctlr->last_subcmd_sent_msecs; 844 845 spin_lock_irqsave(&ctlr->lock, flags); 846 consecutive_valid_deltas = ctlr->consecutive_valid_report_deltas; 847 spin_unlock_irqrestore(&ctlr->lock, flags); 848 849 attempts++; 850 } while ((consecutive_valid_deltas < JC_SUBCMD_VALID_DELTA_REQ || 851 subcmd_delta < JC_SUBCMD_RATE_LIMITER_MS(ctlr)) && 852 ctlr->ctlr_state == JOYCON_CTLR_STATE_READ && 853 attempts < JC_SUBCMD_RATE_MAX_ATTEMPTS); 854 855 if (attempts >= JC_SUBCMD_RATE_MAX_ATTEMPTS) { 856 hid_warn(ctlr->hdev, "%s: exceeded max attempts", __func__); 857 return; 858 } 859 860 ctlr->last_subcmd_sent_msecs = current_ms; 861 862 /* 863 * Wait a short time after receiving an input report before 864 * transmitting. This should reduce odds of a TX coinciding with an RX. 865 * Minimizing concurrent BT traffic with the controller seems to lower 866 * the rate of disconnections. 867 */ 868 msleep(JC_SUBCMD_TX_OFFSET_MS); 869 } 870 871 static int joycon_hid_send_sync(struct joycon_ctlr *ctlr, u8 *data, size_t len, 872 u32 timeout) 873 { 874 int ret; 875 int tries = 2; 876 877 /* 878 * The controller occasionally seems to drop subcommands. In testing, 879 * doing one retry after a timeout appears to always work. 880 */ 881 while (tries--) { 882 joycon_enforce_subcmd_rate(ctlr); 883 884 ret = __joycon_hid_send(ctlr->hdev, data, len); 885 if (ret < 0) { 886 memset(ctlr->input_buf, 0, JC_MAX_RESP_SIZE); 887 return ret; 888 } 889 890 ret = wait_event_timeout(ctlr->wait, ctlr->received_resp, 891 timeout); 892 if (!ret) { 893 hid_dbg(ctlr->hdev, 894 "synchronous send/receive timed out\n"); 895 if (tries) { 896 hid_dbg(ctlr->hdev, 897 "retrying sync send after timeout\n"); 898 } 899 memset(ctlr->input_buf, 0, JC_MAX_RESP_SIZE); 900 ret = -ETIMEDOUT; 901 } else { 902 ret = 0; 903 break; 904 } 905 } 906 907 ctlr->received_resp = false; 908 return ret; 909 } 910 911 static int joycon_send_usb(struct joycon_ctlr *ctlr, u8 cmd, u32 timeout) 912 { 913 int ret; 914 u8 buf[2] = {JC_OUTPUT_USB_CMD}; 915 916 buf[1] = cmd; 917 ctlr->usb_ack_match = cmd; 918 ctlr->msg_type = JOYCON_MSG_TYPE_USB; 919 ret = joycon_hid_send_sync(ctlr, buf, sizeof(buf), timeout); 920 if (ret) 921 hid_dbg(ctlr->hdev, "send usb command failed; ret=%d\n", ret); 922 return ret; 923 } 924 925 static int joycon_send_subcmd(struct joycon_ctlr *ctlr, 926 struct joycon_subcmd_request *subcmd, 927 size_t data_len, u32 timeout) 928 { 929 int ret; 930 unsigned long flags; 931 932 spin_lock_irqsave(&ctlr->lock, flags); 933 /* 934 * If the controller has been removed, just return ENODEV so the LED 935 * subsystem doesn't print invalid errors on removal. 936 */ 937 if (ctlr->ctlr_state == JOYCON_CTLR_STATE_REMOVED) { 938 spin_unlock_irqrestore(&ctlr->lock, flags); 939 return -ENODEV; 940 } 941 memcpy(subcmd->rumble_data, ctlr->rumble_data[ctlr->rumble_queue_tail], 942 JC_RUMBLE_DATA_SIZE); 943 spin_unlock_irqrestore(&ctlr->lock, flags); 944 945 subcmd->output_id = JC_OUTPUT_RUMBLE_AND_SUBCMD; 946 subcmd->packet_num = ctlr->subcmd_num; 947 if (++ctlr->subcmd_num > 0xF) 948 ctlr->subcmd_num = 0; 949 ctlr->subcmd_ack_match = subcmd->subcmd_id; 950 ctlr->msg_type = JOYCON_MSG_TYPE_SUBCMD; 951 952 ret = joycon_hid_send_sync(ctlr, (u8 *)subcmd, 953 sizeof(*subcmd) + data_len, timeout); 954 if (ret < 0) 955 hid_dbg(ctlr->hdev, "send subcommand failed; ret=%d\n", ret); 956 else 957 ret = 0; 958 return ret; 959 } 960 961 /* Supply nibbles for flash and on. Ones correspond to active */ 962 static int joycon_set_player_leds(struct joycon_ctlr *ctlr, u8 flash, u8 on) 963 { 964 struct joycon_subcmd_request *req; 965 u8 buffer[sizeof(*req) + 1] = { 0 }; 966 967 req = (struct joycon_subcmd_request *)buffer; 968 req->subcmd_id = JC_SUBCMD_SET_PLAYER_LIGHTS; 969 req->data[0] = (flash << 4) | on; 970 971 hid_dbg(ctlr->hdev, "setting player leds\n"); 972 return joycon_send_subcmd(ctlr, req, 1, HZ/4); 973 } 974 975 static int joycon_set_home_led(struct joycon_ctlr *ctlr, enum led_brightness brightness) 976 { 977 struct joycon_subcmd_request *req; 978 u8 buffer[sizeof(*req) + 5] = { 0 }; 979 u8 *data; 980 981 req = (struct joycon_subcmd_request *)buffer; 982 req->subcmd_id = JC_SUBCMD_SET_HOME_LIGHT; 983 data = req->data; 984 data[0] = 0x01; 985 data[1] = brightness << 4; 986 data[2] = brightness | (brightness << 4); 987 data[3] = 0x11; 988 data[4] = 0x11; 989 990 hid_dbg(ctlr->hdev, "setting home led brightness\n"); 991 return joycon_send_subcmd(ctlr, req, 5, HZ/4); 992 } 993 994 static int joycon_request_spi_flash_read(struct joycon_ctlr *ctlr, 995 u32 start_addr, u8 size, u8 **reply) 996 { 997 struct joycon_subcmd_request *req; 998 struct joycon_input_report *report; 999 u8 buffer[sizeof(*req) + 5] = { 0 }; 1000 u8 *data; 1001 int ret; 1002 1003 if (!reply) 1004 return -EINVAL; 1005 1006 req = (struct joycon_subcmd_request *)buffer; 1007 req->subcmd_id = JC_SUBCMD_SPI_FLASH_READ; 1008 data = req->data; 1009 put_unaligned_le32(start_addr, data); 1010 data[4] = size; 1011 1012 hid_dbg(ctlr->hdev, "requesting SPI flash data\n"); 1013 ret = joycon_send_subcmd(ctlr, req, 5, HZ); 1014 if (ret) { 1015 hid_err(ctlr->hdev, "failed reading SPI flash; ret=%d\n", ret); 1016 } else { 1017 report = (struct joycon_input_report *)ctlr->input_buf; 1018 /* The read data starts at the 6th byte */ 1019 *reply = &report->subcmd_reply.data[5]; 1020 } 1021 return ret; 1022 } 1023 1024 /* 1025 * User calibration's presence is denoted with a magic byte preceding it. 1026 * returns 0 if magic val is present, 1 if not present, < 0 on error 1027 */ 1028 static int joycon_check_for_cal_magic(struct joycon_ctlr *ctlr, u32 flash_addr) 1029 { 1030 int ret; 1031 u8 *reply; 1032 1033 ret = joycon_request_spi_flash_read(ctlr, flash_addr, 1034 JC_CAL_USR_MAGIC_SIZE, &reply); 1035 if (ret) 1036 return ret; 1037 1038 return reply[0] != JC_CAL_USR_MAGIC_0 || reply[1] != JC_CAL_USR_MAGIC_1; 1039 } 1040 1041 static int joycon_read_stick_calibration(struct joycon_ctlr *ctlr, u16 cal_addr, 1042 struct joycon_stick_cal *cal_x, 1043 struct joycon_stick_cal *cal_y, 1044 bool left_stick) 1045 { 1046 s32 x_max_above; 1047 s32 x_min_below; 1048 s32 y_max_above; 1049 s32 y_min_below; 1050 u8 *raw_cal; 1051 int ret; 1052 1053 ret = joycon_request_spi_flash_read(ctlr, cal_addr, 1054 JC_CAL_STICK_DATA_SIZE, &raw_cal); 1055 if (ret) 1056 return ret; 1057 1058 /* stick calibration parsing: note the order differs based on stick */ 1059 if (left_stick) { 1060 x_max_above = hid_field_extract(ctlr->hdev, (raw_cal + 0), 0, 1061 12); 1062 y_max_above = hid_field_extract(ctlr->hdev, (raw_cal + 1), 4, 1063 12); 1064 cal_x->center = hid_field_extract(ctlr->hdev, (raw_cal + 3), 0, 1065 12); 1066 cal_y->center = hid_field_extract(ctlr->hdev, (raw_cal + 4), 4, 1067 12); 1068 x_min_below = hid_field_extract(ctlr->hdev, (raw_cal + 6), 0, 1069 12); 1070 y_min_below = hid_field_extract(ctlr->hdev, (raw_cal + 7), 4, 1071 12); 1072 } else { 1073 cal_x->center = hid_field_extract(ctlr->hdev, (raw_cal + 0), 0, 1074 12); 1075 cal_y->center = hid_field_extract(ctlr->hdev, (raw_cal + 1), 4, 1076 12); 1077 x_min_below = hid_field_extract(ctlr->hdev, (raw_cal + 3), 0, 1078 12); 1079 y_min_below = hid_field_extract(ctlr->hdev, (raw_cal + 4), 4, 1080 12); 1081 x_max_above = hid_field_extract(ctlr->hdev, (raw_cal + 6), 0, 1082 12); 1083 y_max_above = hid_field_extract(ctlr->hdev, (raw_cal + 7), 4, 1084 12); 1085 } 1086 1087 cal_x->max = cal_x->center + x_max_above; 1088 cal_x->min = cal_x->center - x_min_below; 1089 cal_y->max = cal_y->center + y_max_above; 1090 cal_y->min = cal_y->center - y_min_below; 1091 1092 /* check if calibration values are plausible */ 1093 if (cal_x->min >= cal_x->center || cal_x->center >= cal_x->max || 1094 cal_y->min >= cal_y->center || cal_y->center >= cal_y->max) 1095 ret = -EINVAL; 1096 1097 return ret; 1098 } 1099 1100 static const u16 DFLT_STICK_CAL_CEN = 2000; 1101 static const u16 DFLT_STICK_CAL_MAX = 3500; 1102 static const u16 DFLT_STICK_CAL_MIN = 500; 1103 static void joycon_use_default_calibration(struct hid_device *hdev, 1104 struct joycon_stick_cal *cal_x, 1105 struct joycon_stick_cal *cal_y, 1106 const char *stick, int ret) 1107 { 1108 hid_warn(hdev, 1109 "Failed to read %s stick cal, using defaults; e=%d\n", 1110 stick, ret); 1111 1112 cal_x->center = cal_y->center = DFLT_STICK_CAL_CEN; 1113 cal_x->max = cal_y->max = DFLT_STICK_CAL_MAX; 1114 cal_x->min = cal_y->min = DFLT_STICK_CAL_MIN; 1115 } 1116 1117 static int joycon_request_calibration(struct joycon_ctlr *ctlr) 1118 { 1119 u16 left_stick_addr = JC_CAL_FCT_DATA_LEFT_ADDR; 1120 u16 right_stick_addr = JC_CAL_FCT_DATA_RIGHT_ADDR; 1121 int ret; 1122 1123 hid_dbg(ctlr->hdev, "requesting cal data\n"); 1124 1125 /* check if user stick calibrations are present */ 1126 if (!joycon_check_for_cal_magic(ctlr, JC_CAL_USR_LEFT_MAGIC_ADDR)) { 1127 left_stick_addr = JC_CAL_USR_LEFT_DATA_ADDR; 1128 hid_info(ctlr->hdev, "using user cal for left stick\n"); 1129 } else { 1130 hid_info(ctlr->hdev, "using factory cal for left stick\n"); 1131 } 1132 if (!joycon_check_for_cal_magic(ctlr, JC_CAL_USR_RIGHT_MAGIC_ADDR)) { 1133 right_stick_addr = JC_CAL_USR_RIGHT_DATA_ADDR; 1134 hid_info(ctlr->hdev, "using user cal for right stick\n"); 1135 } else { 1136 hid_info(ctlr->hdev, "using factory cal for right stick\n"); 1137 } 1138 1139 /* read the left stick calibration data */ 1140 ret = joycon_read_stick_calibration(ctlr, left_stick_addr, 1141 &ctlr->left_stick_cal_x, 1142 &ctlr->left_stick_cal_y, 1143 true); 1144 1145 if (ret) 1146 joycon_use_default_calibration(ctlr->hdev, 1147 &ctlr->left_stick_cal_x, 1148 &ctlr->left_stick_cal_y, 1149 "left", ret); 1150 1151 /* read the right stick calibration data */ 1152 ret = joycon_read_stick_calibration(ctlr, right_stick_addr, 1153 &ctlr->right_stick_cal_x, 1154 &ctlr->right_stick_cal_y, 1155 false); 1156 1157 if (ret) 1158 joycon_use_default_calibration(ctlr->hdev, 1159 &ctlr->right_stick_cal_x, 1160 &ctlr->right_stick_cal_y, 1161 "right", ret); 1162 1163 hid_dbg(ctlr->hdev, "calibration:\n" 1164 "l_x_c=%d l_x_max=%d l_x_min=%d\n" 1165 "l_y_c=%d l_y_max=%d l_y_min=%d\n" 1166 "r_x_c=%d r_x_max=%d r_x_min=%d\n" 1167 "r_y_c=%d r_y_max=%d r_y_min=%d\n", 1168 ctlr->left_stick_cal_x.center, 1169 ctlr->left_stick_cal_x.max, 1170 ctlr->left_stick_cal_x.min, 1171 ctlr->left_stick_cal_y.center, 1172 ctlr->left_stick_cal_y.max, 1173 ctlr->left_stick_cal_y.min, 1174 ctlr->right_stick_cal_x.center, 1175 ctlr->right_stick_cal_x.max, 1176 ctlr->right_stick_cal_x.min, 1177 ctlr->right_stick_cal_y.center, 1178 ctlr->right_stick_cal_y.max, 1179 ctlr->right_stick_cal_y.min); 1180 1181 return 0; 1182 } 1183 1184 /* 1185 * These divisors are calculated once rather than for each sample. They are only 1186 * dependent on the IMU calibration values. They are used when processing the 1187 * IMU input reports. 1188 */ 1189 static void joycon_calc_imu_cal_divisors(struct joycon_ctlr *ctlr) 1190 { 1191 int i, divz = 0; 1192 1193 for (i = 0; i < 3; i++) { 1194 ctlr->imu_cal_accel_divisor[i] = ctlr->accel_cal.scale[i] - 1195 ctlr->accel_cal.offset[i]; 1196 ctlr->imu_cal_gyro_divisor[i] = ctlr->gyro_cal.scale[i] - 1197 ctlr->gyro_cal.offset[i]; 1198 1199 if (ctlr->imu_cal_accel_divisor[i] == 0) { 1200 ctlr->imu_cal_accel_divisor[i] = 1; 1201 divz++; 1202 } 1203 1204 if (ctlr->imu_cal_gyro_divisor[i] == 0) { 1205 ctlr->imu_cal_gyro_divisor[i] = 1; 1206 divz++; 1207 } 1208 } 1209 1210 if (divz) 1211 hid_warn(ctlr->hdev, "inaccurate IMU divisors (%d)\n", divz); 1212 } 1213 1214 static const s16 DFLT_ACCEL_OFFSET /*= 0*/; 1215 static const s16 DFLT_ACCEL_SCALE = 16384; 1216 static const s16 DFLT_GYRO_OFFSET /*= 0*/; 1217 static const s16 DFLT_GYRO_SCALE = 13371; 1218 static int joycon_request_imu_calibration(struct joycon_ctlr *ctlr) 1219 { 1220 u16 imu_cal_addr = JC_IMU_CAL_FCT_DATA_ADDR; 1221 u8 *raw_cal; 1222 int ret; 1223 int i; 1224 1225 /* check if user calibration exists */ 1226 if (!joycon_check_for_cal_magic(ctlr, JC_IMU_CAL_USR_MAGIC_ADDR)) { 1227 imu_cal_addr = JC_IMU_CAL_USR_DATA_ADDR; 1228 hid_info(ctlr->hdev, "using user cal for IMU\n"); 1229 } else { 1230 hid_info(ctlr->hdev, "using factory cal for IMU\n"); 1231 } 1232 1233 /* request IMU calibration data */ 1234 hid_dbg(ctlr->hdev, "requesting IMU cal data\n"); 1235 ret = joycon_request_spi_flash_read(ctlr, imu_cal_addr, 1236 JC_IMU_CAL_DATA_SIZE, &raw_cal); 1237 if (ret) { 1238 hid_warn(ctlr->hdev, 1239 "Failed to read IMU cal, using defaults; ret=%d\n", 1240 ret); 1241 1242 for (i = 0; i < 3; i++) { 1243 ctlr->accel_cal.offset[i] = DFLT_ACCEL_OFFSET; 1244 ctlr->accel_cal.scale[i] = DFLT_ACCEL_SCALE; 1245 ctlr->gyro_cal.offset[i] = DFLT_GYRO_OFFSET; 1246 ctlr->gyro_cal.scale[i] = DFLT_GYRO_SCALE; 1247 } 1248 joycon_calc_imu_cal_divisors(ctlr); 1249 return ret; 1250 } 1251 1252 /* IMU calibration parsing */ 1253 for (i = 0; i < 3; i++) { 1254 int j = i * 2; 1255 1256 ctlr->accel_cal.offset[i] = get_unaligned_le16(raw_cal + j); 1257 ctlr->accel_cal.scale[i] = get_unaligned_le16(raw_cal + j + 6); 1258 ctlr->gyro_cal.offset[i] = get_unaligned_le16(raw_cal + j + 12); 1259 ctlr->gyro_cal.scale[i] = get_unaligned_le16(raw_cal + j + 18); 1260 } 1261 1262 joycon_calc_imu_cal_divisors(ctlr); 1263 1264 hid_dbg(ctlr->hdev, "IMU calibration:\n" 1265 "a_o[0]=%d a_o[1]=%d a_o[2]=%d\n" 1266 "a_s[0]=%d a_s[1]=%d a_s[2]=%d\n" 1267 "g_o[0]=%d g_o[1]=%d g_o[2]=%d\n" 1268 "g_s[0]=%d g_s[1]=%d g_s[2]=%d\n", 1269 ctlr->accel_cal.offset[0], 1270 ctlr->accel_cal.offset[1], 1271 ctlr->accel_cal.offset[2], 1272 ctlr->accel_cal.scale[0], 1273 ctlr->accel_cal.scale[1], 1274 ctlr->accel_cal.scale[2], 1275 ctlr->gyro_cal.offset[0], 1276 ctlr->gyro_cal.offset[1], 1277 ctlr->gyro_cal.offset[2], 1278 ctlr->gyro_cal.scale[0], 1279 ctlr->gyro_cal.scale[1], 1280 ctlr->gyro_cal.scale[2]); 1281 1282 return 0; 1283 } 1284 1285 static int joycon_set_report_mode(struct joycon_ctlr *ctlr) 1286 { 1287 struct joycon_subcmd_request *req; 1288 u8 buffer[sizeof(*req) + 1] = { 0 }; 1289 1290 req = (struct joycon_subcmd_request *)buffer; 1291 req->subcmd_id = JC_SUBCMD_SET_REPORT_MODE; 1292 req->data[0] = 0x30; /* standard, full report mode */ 1293 1294 hid_dbg(ctlr->hdev, "setting controller report mode\n"); 1295 return joycon_send_subcmd(ctlr, req, 1, HZ); 1296 } 1297 1298 static int joycon_enable_rumble(struct joycon_ctlr *ctlr) 1299 { 1300 struct joycon_subcmd_request *req; 1301 u8 buffer[sizeof(*req) + 1] = { 0 }; 1302 1303 req = (struct joycon_subcmd_request *)buffer; 1304 req->subcmd_id = JC_SUBCMD_ENABLE_VIBRATION; 1305 req->data[0] = 0x01; /* note: 0x00 would disable */ 1306 1307 hid_dbg(ctlr->hdev, "enabling rumble\n"); 1308 return joycon_send_subcmd(ctlr, req, 1, HZ/4); 1309 } 1310 1311 static int joycon_enable_imu(struct joycon_ctlr *ctlr) 1312 { 1313 struct joycon_subcmd_request *req; 1314 u8 buffer[sizeof(*req) + 1] = { 0 }; 1315 1316 req = (struct joycon_subcmd_request *)buffer; 1317 req->subcmd_id = JC_SUBCMD_ENABLE_IMU; 1318 req->data[0] = 0x01; /* note: 0x00 would disable */ 1319 1320 hid_dbg(ctlr->hdev, "enabling IMU\n"); 1321 return joycon_send_subcmd(ctlr, req, 1, HZ); 1322 } 1323 1324 static s32 joycon_map_stick_val(struct joycon_stick_cal *cal, s32 val) 1325 { 1326 s32 center = cal->center; 1327 s32 min = cal->min; 1328 s32 max = cal->max; 1329 s32 new_val; 1330 1331 if (val > center) { 1332 new_val = (val - center) * JC_MAX_STICK_MAG; 1333 new_val /= (max - center); 1334 } else { 1335 new_val = (center - val) * -JC_MAX_STICK_MAG; 1336 new_val /= (center - min); 1337 } 1338 new_val = clamp(new_val, (s32)-JC_MAX_STICK_MAG, (s32)JC_MAX_STICK_MAG); 1339 return new_val; 1340 } 1341 1342 static void joycon_input_report_parse_imu_data(struct joycon_ctlr *ctlr, 1343 struct joycon_input_report *rep, 1344 struct joycon_imu_data *imu_data) 1345 { 1346 u8 *raw = rep->imu_raw_bytes; 1347 int i; 1348 1349 for (i = 0; i < 3; i++) { 1350 struct joycon_imu_data *data = &imu_data[i]; 1351 1352 data->accel_x = get_unaligned_le16(raw + 0); 1353 data->accel_y = get_unaligned_le16(raw + 2); 1354 data->accel_z = get_unaligned_le16(raw + 4); 1355 data->gyro_x = get_unaligned_le16(raw + 6); 1356 data->gyro_y = get_unaligned_le16(raw + 8); 1357 data->gyro_z = get_unaligned_le16(raw + 10); 1358 /* point to next imu sample */ 1359 raw += sizeof(struct joycon_imu_data); 1360 } 1361 } 1362 1363 static void joycon_parse_imu_report(struct joycon_ctlr *ctlr, 1364 struct joycon_input_report *rep) 1365 { 1366 struct joycon_imu_data imu_data[3] = {0}; /* 3 reports per packet */ 1367 struct input_dev *idev = ctlr->imu_input; 1368 unsigned int msecs = jiffies_to_msecs(jiffies); 1369 unsigned int last_msecs = ctlr->imu_last_pkt_ms; 1370 int i; 1371 int value[6]; 1372 1373 joycon_input_report_parse_imu_data(ctlr, rep, imu_data); 1374 1375 /* 1376 * There are complexities surrounding how we determine the timestamps we 1377 * associate with the samples we pass to userspace. The IMU input 1378 * reports do not provide us with a good timestamp. There's a quickly 1379 * incrementing 8-bit counter per input report, but it is not very 1380 * useful for this purpose (it is not entirely clear what rate it 1381 * increments at or if it varies based on packet push rate - more on 1382 * the push rate below...). 1383 * 1384 * The reverse engineering work done on the joy-cons and pro controllers 1385 * by the community seems to indicate the following: 1386 * - The controller samples the IMU every 1.35ms. It then does some of 1387 * its own processing, probably averaging the samples out. 1388 * - Each imu input report contains 3 IMU samples, (usually 5ms apart). 1389 * - In the standard reporting mode (which this driver uses exclusively) 1390 * input reports are pushed from the controller as follows: 1391 * * joy-con (bluetooth): every 15 ms 1392 * * joy-cons (in charging grip via USB): every 15 ms 1393 * * pro controller (USB): every 15 ms 1394 * * pro controller (bluetooth): every 8 ms (this is the wildcard) 1395 * 1396 * Further complicating matters is that some bluetooth stacks are known 1397 * to alter the controller's packet rate by hardcoding the bluetooth 1398 * SSR for the switch controllers (android's stack currently sets the 1399 * SSR to 11ms for both the joy-cons and pro controllers). 1400 * 1401 * In my own testing, I've discovered that my pro controller either 1402 * reports IMU sample batches every 11ms or every 15ms. This rate is 1403 * stable after connecting. It isn't 100% clear what determines this 1404 * rate. Importantly, even when sending every 11ms, none of the samples 1405 * are duplicates. This seems to indicate that the time deltas between 1406 * reported samples can vary based on the input report rate. 1407 * 1408 * The solution employed in this driver is to keep track of the average 1409 * time delta between IMU input reports. In testing, this value has 1410 * proven to be stable, staying at 15ms or 11ms, though other hardware 1411 * configurations and bluetooth stacks could potentially see other rates 1412 * (hopefully this will become more clear as more people use the 1413 * driver). 1414 * 1415 * Keeping track of the average report delta allows us to submit our 1416 * timestamps to userspace based on that. Each report contains 3 1417 * samples, so the IMU sampling rate should be avg_time_delta/3. We can 1418 * also use this average to detect events where we have dropped a 1419 * packet. The userspace timestamp for the samples will be adjusted 1420 * accordingly to prevent unwanted behvaior. 1421 */ 1422 if (!ctlr->imu_first_packet_received) { 1423 ctlr->imu_timestamp_us = 0; 1424 ctlr->imu_delta_samples_count = 0; 1425 ctlr->imu_delta_samples_sum = 0; 1426 ctlr->imu_avg_delta_ms = JC_IMU_DFLT_AVG_DELTA_MS; 1427 ctlr->imu_first_packet_received = true; 1428 } else { 1429 unsigned int delta = msecs - last_msecs; 1430 unsigned int dropped_pkts; 1431 unsigned int dropped_threshold; 1432 1433 /* avg imu report delta housekeeping */ 1434 ctlr->imu_delta_samples_sum += delta; 1435 ctlr->imu_delta_samples_count++; 1436 if (ctlr->imu_delta_samples_count >= 1437 JC_IMU_SAMPLES_PER_DELTA_AVG) { 1438 ctlr->imu_avg_delta_ms = ctlr->imu_delta_samples_sum / 1439 ctlr->imu_delta_samples_count; 1440 ctlr->imu_delta_samples_count = 0; 1441 ctlr->imu_delta_samples_sum = 0; 1442 } 1443 1444 /* don't ever want divide by zero shenanigans */ 1445 if (ctlr->imu_avg_delta_ms == 0) { 1446 ctlr->imu_avg_delta_ms = 1; 1447 hid_warn(ctlr->hdev, "calculated avg imu delta of 0\n"); 1448 } 1449 1450 /* useful for debugging IMU sample rate */ 1451 hid_dbg(ctlr->hdev, 1452 "imu_report: ms=%u last_ms=%u delta=%u avg_delta=%u\n", 1453 msecs, last_msecs, delta, ctlr->imu_avg_delta_ms); 1454 1455 /* check if any packets have been dropped */ 1456 dropped_threshold = ctlr->imu_avg_delta_ms * 3 / 2; 1457 dropped_pkts = (delta - min(delta, dropped_threshold)) / 1458 ctlr->imu_avg_delta_ms; 1459 ctlr->imu_timestamp_us += 1000 * ctlr->imu_avg_delta_ms; 1460 if (dropped_pkts > JC_IMU_DROPPED_PKT_WARNING) { 1461 hid_warn(ctlr->hdev, 1462 "compensating for %u dropped IMU reports\n", 1463 dropped_pkts); 1464 hid_warn(ctlr->hdev, 1465 "delta=%u avg_delta=%u\n", 1466 delta, ctlr->imu_avg_delta_ms); 1467 } 1468 } 1469 ctlr->imu_last_pkt_ms = msecs; 1470 1471 /* Each IMU input report contains three samples */ 1472 for (i = 0; i < 3; i++) { 1473 input_event(idev, EV_MSC, MSC_TIMESTAMP, 1474 ctlr->imu_timestamp_us); 1475 1476 /* 1477 * These calculations (which use the controller's calibration 1478 * settings to improve the final values) are based on those 1479 * found in the community's reverse-engineering repo (linked at 1480 * top of driver). For hid-nintendo, we make sure that the final 1481 * value given to userspace is always in terms of the axis 1482 * resolution we provided. 1483 * 1484 * Currently only the gyro calculations subtract the calibration 1485 * offsets from the raw value itself. In testing, doing the same 1486 * for the accelerometer raw values decreased accuracy. 1487 * 1488 * Note that the gyro values are multiplied by the 1489 * precision-saving scaling factor to prevent large inaccuracies 1490 * due to truncation of the resolution value which would 1491 * otherwise occur. To prevent overflow (without resorting to 64 1492 * bit integer math), the mult_frac macro is used. 1493 */ 1494 value[0] = mult_frac((JC_IMU_PREC_RANGE_SCALE * 1495 (imu_data[i].gyro_x - 1496 ctlr->gyro_cal.offset[0])), 1497 ctlr->gyro_cal.scale[0], 1498 ctlr->imu_cal_gyro_divisor[0]); 1499 value[1] = mult_frac((JC_IMU_PREC_RANGE_SCALE * 1500 (imu_data[i].gyro_y - 1501 ctlr->gyro_cal.offset[1])), 1502 ctlr->gyro_cal.scale[1], 1503 ctlr->imu_cal_gyro_divisor[1]); 1504 value[2] = mult_frac((JC_IMU_PREC_RANGE_SCALE * 1505 (imu_data[i].gyro_z - 1506 ctlr->gyro_cal.offset[2])), 1507 ctlr->gyro_cal.scale[2], 1508 ctlr->imu_cal_gyro_divisor[2]); 1509 1510 value[3] = ((s32)imu_data[i].accel_x * 1511 ctlr->accel_cal.scale[0]) / 1512 ctlr->imu_cal_accel_divisor[0]; 1513 value[4] = ((s32)imu_data[i].accel_y * 1514 ctlr->accel_cal.scale[1]) / 1515 ctlr->imu_cal_accel_divisor[1]; 1516 value[5] = ((s32)imu_data[i].accel_z * 1517 ctlr->accel_cal.scale[2]) / 1518 ctlr->imu_cal_accel_divisor[2]; 1519 1520 hid_dbg(ctlr->hdev, "raw_gyro: g_x=%d g_y=%d g_z=%d\n", 1521 imu_data[i].gyro_x, imu_data[i].gyro_y, 1522 imu_data[i].gyro_z); 1523 hid_dbg(ctlr->hdev, "raw_accel: a_x=%d a_y=%d a_z=%d\n", 1524 imu_data[i].accel_x, imu_data[i].accel_y, 1525 imu_data[i].accel_z); 1526 1527 /* 1528 * The right joy-con has 2 axes negated, Y and Z. This is due to 1529 * the orientation of the IMU in the controller. We negate those 1530 * axes' values in order to be consistent with the left joy-con 1531 * and the pro controller: 1532 * X: positive is pointing toward the triggers 1533 * Y: positive is pointing to the left 1534 * Z: positive is pointing up (out of the buttons/sticks) 1535 * The axes follow the right-hand rule. 1536 */ 1537 if (jc_type_is_joycon(ctlr) && jc_type_has_right(ctlr)) { 1538 int j; 1539 1540 /* negate all but x axis */ 1541 for (j = 1; j < 6; ++j) { 1542 if (j == 3) 1543 continue; 1544 value[j] *= -1; 1545 } 1546 } 1547 1548 input_report_abs(idev, ABS_RX, value[0]); 1549 input_report_abs(idev, ABS_RY, value[1]); 1550 input_report_abs(idev, ABS_RZ, value[2]); 1551 input_report_abs(idev, ABS_X, value[3]); 1552 input_report_abs(idev, ABS_Y, value[4]); 1553 input_report_abs(idev, ABS_Z, value[5]); 1554 input_sync(idev); 1555 /* convert to micros and divide by 3 (3 samples per report). */ 1556 ctlr->imu_timestamp_us += ctlr->imu_avg_delta_ms * 1000 / 3; 1557 } 1558 } 1559 1560 static void joycon_handle_rumble_report(struct joycon_ctlr *ctlr, struct joycon_input_report *rep) 1561 { 1562 unsigned long flags; 1563 unsigned long msecs = jiffies_to_msecs(jiffies); 1564 1565 spin_lock_irqsave(&ctlr->lock, flags); 1566 if (IS_ENABLED(CONFIG_NINTENDO_FF) && rep->vibrator_report && 1567 ctlr->ctlr_state != JOYCON_CTLR_STATE_REMOVED && 1568 (msecs - ctlr->rumble_msecs) >= JC_RUMBLE_PERIOD_MS && 1569 (ctlr->rumble_queue_head != ctlr->rumble_queue_tail || 1570 ctlr->rumble_zero_countdown > 0)) { 1571 /* 1572 * When this value reaches 0, we know we've sent multiple 1573 * packets to the controller instructing it to disable rumble. 1574 * We can safely stop sending periodic rumble packets until the 1575 * next ff effect. 1576 */ 1577 if (ctlr->rumble_zero_countdown > 0) 1578 ctlr->rumble_zero_countdown--; 1579 queue_work(ctlr->rumble_queue, &ctlr->rumble_worker); 1580 } 1581 1582 spin_unlock_irqrestore(&ctlr->lock, flags); 1583 } 1584 1585 static void joycon_parse_battery_status(struct joycon_ctlr *ctlr, struct joycon_input_report *rep) 1586 { 1587 u8 tmp; 1588 unsigned long flags; 1589 1590 spin_lock_irqsave(&ctlr->lock, flags); 1591 1592 tmp = rep->bat_con; 1593 ctlr->host_powered = tmp & BIT(0); 1594 ctlr->battery_charging = tmp & BIT(4); 1595 tmp = tmp >> 5; 1596 1597 switch (tmp) { 1598 case 0: /* empty */ 1599 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_CRITICAL; 1600 break; 1601 case 1: /* low */ 1602 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_LOW; 1603 break; 1604 case 2: /* medium */ 1605 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_NORMAL; 1606 break; 1607 case 3: /* high */ 1608 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_HIGH; 1609 break; 1610 case 4: /* full */ 1611 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_FULL; 1612 break; 1613 default: 1614 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_UNKNOWN; 1615 hid_warn(ctlr->hdev, "Invalid battery status\n"); 1616 break; 1617 } 1618 1619 spin_unlock_irqrestore(&ctlr->lock, flags); 1620 } 1621 1622 static void joycon_report_left_stick(struct joycon_ctlr *ctlr, 1623 struct joycon_input_report *rep) 1624 { 1625 u16 raw_x; 1626 u16 raw_y; 1627 s32 x; 1628 s32 y; 1629 1630 raw_x = hid_field_extract(ctlr->hdev, rep->left_stick, 0, 12); 1631 raw_y = hid_field_extract(ctlr->hdev, rep->left_stick + 1, 4, 12); 1632 1633 x = joycon_map_stick_val(&ctlr->left_stick_cal_x, raw_x); 1634 y = -joycon_map_stick_val(&ctlr->left_stick_cal_y, raw_y); 1635 1636 input_report_abs(ctlr->input, ABS_X, x); 1637 input_report_abs(ctlr->input, ABS_Y, y); 1638 } 1639 1640 static void joycon_report_right_stick(struct joycon_ctlr *ctlr, 1641 struct joycon_input_report *rep) 1642 { 1643 u16 raw_x; 1644 u16 raw_y; 1645 s32 x; 1646 s32 y; 1647 1648 raw_x = hid_field_extract(ctlr->hdev, rep->right_stick, 0, 12); 1649 raw_y = hid_field_extract(ctlr->hdev, rep->right_stick + 1, 4, 12); 1650 1651 x = joycon_map_stick_val(&ctlr->right_stick_cal_x, raw_x); 1652 y = -joycon_map_stick_val(&ctlr->right_stick_cal_y, raw_y); 1653 1654 input_report_abs(ctlr->input, ABS_RX, x); 1655 input_report_abs(ctlr->input, ABS_RY, y); 1656 } 1657 1658 static void joycon_report_dpad(struct joycon_ctlr *ctlr, 1659 struct joycon_input_report *rep) 1660 { 1661 int hatx = 0; 1662 int haty = 0; 1663 u32 btns = hid_field_extract(ctlr->hdev, rep->button_status, 0, 24); 1664 1665 if (btns & JC_BTN_LEFT) 1666 hatx = -1; 1667 else if (btns & JC_BTN_RIGHT) 1668 hatx = 1; 1669 1670 if (btns & JC_BTN_UP) 1671 haty = -1; 1672 else if (btns & JC_BTN_DOWN) 1673 haty = 1; 1674 1675 input_report_abs(ctlr->input, ABS_HAT0X, hatx); 1676 input_report_abs(ctlr->input, ABS_HAT0Y, haty); 1677 } 1678 1679 static void joycon_report_buttons(struct joycon_ctlr *ctlr, 1680 struct joycon_input_report *rep, 1681 const struct joycon_ctlr_button_mapping button_mappings[]) 1682 { 1683 const struct joycon_ctlr_button_mapping *button; 1684 u32 status = hid_field_extract(ctlr->hdev, rep->button_status, 0, 24); 1685 1686 for (button = button_mappings; button->code; button++) 1687 input_report_key(ctlr->input, button->code, status & button->bit); 1688 } 1689 1690 static void joycon_parse_report(struct joycon_ctlr *ctlr, 1691 struct joycon_input_report *rep) 1692 { 1693 unsigned long flags; 1694 unsigned long msecs = jiffies_to_msecs(jiffies); 1695 unsigned long report_delta_ms = msecs - ctlr->last_input_report_msecs; 1696 1697 if (joycon_has_rumble(ctlr)) 1698 joycon_handle_rumble_report(ctlr, rep); 1699 1700 joycon_parse_battery_status(ctlr, rep); 1701 1702 if (joycon_type_is_left_joycon(ctlr)) { 1703 joycon_report_left_stick(ctlr, rep); 1704 joycon_report_buttons(ctlr, rep, left_joycon_button_mappings); 1705 if (!joycon_device_is_chrggrip(ctlr)) 1706 joycon_report_buttons(ctlr, rep, left_joycon_s_button_mappings); 1707 } else if (joycon_type_is_right_joycon(ctlr)) { 1708 joycon_report_right_stick(ctlr, rep); 1709 joycon_report_buttons(ctlr, rep, right_joycon_button_mappings); 1710 if (!joycon_device_is_chrggrip(ctlr)) 1711 joycon_report_buttons(ctlr, rep, right_joycon_s_button_mappings); 1712 } else if (joycon_type_is_procon(ctlr)) { 1713 joycon_report_left_stick(ctlr, rep); 1714 joycon_report_right_stick(ctlr, rep); 1715 joycon_report_dpad(ctlr, rep); 1716 joycon_report_buttons(ctlr, rep, procon_button_mappings); 1717 } else if (joycon_type_is_any_nescon(ctlr)) { 1718 joycon_report_dpad(ctlr, rep); 1719 joycon_report_buttons(ctlr, rep, nescon_button_mappings); 1720 } else if (joycon_type_is_snescon(ctlr)) { 1721 joycon_report_dpad(ctlr, rep); 1722 joycon_report_buttons(ctlr, rep, snescon_button_mappings); 1723 } else if (joycon_type_is_gencon(ctlr)) { 1724 joycon_report_dpad(ctlr, rep); 1725 joycon_report_buttons(ctlr, rep, gencon_button_mappings); 1726 } else if (joycon_type_is_n64con(ctlr)) { 1727 joycon_report_left_stick(ctlr, rep); 1728 joycon_report_dpad(ctlr, rep); 1729 joycon_report_buttons(ctlr, rep, n64con_button_mappings); 1730 } 1731 1732 input_sync(ctlr->input); 1733 1734 spin_lock_irqsave(&ctlr->lock, flags); 1735 ctlr->last_input_report_msecs = msecs; 1736 /* 1737 * Was this input report a reasonable time delta compared to the prior 1738 * report? We use this information to decide when a safe time is to send 1739 * rumble packets or subcommand packets. 1740 */ 1741 if (report_delta_ms >= JC_INPUT_REPORT_MIN_DELTA && 1742 report_delta_ms <= JC_INPUT_REPORT_MAX_DELTA) { 1743 if (ctlr->consecutive_valid_report_deltas < JC_SUBCMD_VALID_DELTA_REQ) 1744 ctlr->consecutive_valid_report_deltas++; 1745 } else { 1746 ctlr->consecutive_valid_report_deltas = 0; 1747 } 1748 /* 1749 * Our consecutive valid report tracking is only relevant for 1750 * bluetooth-connected controllers. For USB devices, we're beholden to 1751 * USB's underlying polling rate anyway. Always set to the consecutive 1752 * delta requirement. 1753 */ 1754 if (ctlr->hdev->bus == BUS_USB) 1755 ctlr->consecutive_valid_report_deltas = JC_SUBCMD_VALID_DELTA_REQ; 1756 1757 spin_unlock_irqrestore(&ctlr->lock, flags); 1758 1759 /* 1760 * Immediately after receiving a report is the most reliable time to 1761 * send a subcommand to the controller. Wake any subcommand senders 1762 * waiting for a report. 1763 */ 1764 if (unlikely(mutex_is_locked(&ctlr->output_mutex))) { 1765 spin_lock_irqsave(&ctlr->lock, flags); 1766 ctlr->received_input_report = true; 1767 spin_unlock_irqrestore(&ctlr->lock, flags); 1768 wake_up(&ctlr->wait); 1769 } 1770 1771 /* parse IMU data if present */ 1772 if ((rep->id == JC_INPUT_IMU_DATA) && joycon_has_imu(ctlr)) 1773 joycon_parse_imu_report(ctlr, rep); 1774 } 1775 1776 static int joycon_send_rumble_data(struct joycon_ctlr *ctlr) 1777 { 1778 int ret; 1779 unsigned long flags; 1780 struct joycon_rumble_output rumble_output = { 0 }; 1781 1782 spin_lock_irqsave(&ctlr->lock, flags); 1783 /* 1784 * If the controller has been removed, just return ENODEV so the LED 1785 * subsystem doesn't print invalid errors on removal. 1786 */ 1787 if (ctlr->ctlr_state == JOYCON_CTLR_STATE_REMOVED) { 1788 spin_unlock_irqrestore(&ctlr->lock, flags); 1789 return -ENODEV; 1790 } 1791 memcpy(rumble_output.rumble_data, 1792 ctlr->rumble_data[ctlr->rumble_queue_tail], 1793 JC_RUMBLE_DATA_SIZE); 1794 spin_unlock_irqrestore(&ctlr->lock, flags); 1795 1796 rumble_output.output_id = JC_OUTPUT_RUMBLE_ONLY; 1797 rumble_output.packet_num = ctlr->subcmd_num; 1798 if (++ctlr->subcmd_num > 0xF) 1799 ctlr->subcmd_num = 0; 1800 1801 joycon_enforce_subcmd_rate(ctlr); 1802 1803 ret = __joycon_hid_send(ctlr->hdev, (u8 *)&rumble_output, 1804 sizeof(rumble_output)); 1805 return ret; 1806 } 1807 1808 static void joycon_rumble_worker(struct work_struct *work) 1809 { 1810 struct joycon_ctlr *ctlr = container_of(work, struct joycon_ctlr, 1811 rumble_worker); 1812 unsigned long flags; 1813 bool again = true; 1814 int ret; 1815 1816 while (again) { 1817 mutex_lock(&ctlr->output_mutex); 1818 ret = joycon_send_rumble_data(ctlr); 1819 mutex_unlock(&ctlr->output_mutex); 1820 1821 /* -ENODEV means the controller was just unplugged */ 1822 spin_lock_irqsave(&ctlr->lock, flags); 1823 if (ret < 0 && ret != -ENODEV && 1824 ctlr->ctlr_state != JOYCON_CTLR_STATE_REMOVED) 1825 hid_warn(ctlr->hdev, "Failed to set rumble; e=%d", ret); 1826 1827 ctlr->rumble_msecs = jiffies_to_msecs(jiffies); 1828 if (ctlr->rumble_queue_tail != ctlr->rumble_queue_head) { 1829 if (++ctlr->rumble_queue_tail >= JC_RUMBLE_QUEUE_SIZE) 1830 ctlr->rumble_queue_tail = 0; 1831 } else { 1832 again = false; 1833 } 1834 spin_unlock_irqrestore(&ctlr->lock, flags); 1835 } 1836 } 1837 1838 #if IS_ENABLED(CONFIG_NINTENDO_FF) 1839 static struct joycon_rumble_freq_data joycon_find_rumble_freq(u16 freq) 1840 { 1841 const size_t length = ARRAY_SIZE(joycon_rumble_frequencies); 1842 const struct joycon_rumble_freq_data *data = joycon_rumble_frequencies; 1843 int i = 0; 1844 1845 if (freq > data[0].freq) { 1846 for (i = 1; i < length - 1; i++) { 1847 if (freq > data[i - 1].freq && freq <= data[i].freq) 1848 break; 1849 } 1850 } 1851 1852 return data[i]; 1853 } 1854 1855 static struct joycon_rumble_amp_data joycon_find_rumble_amp(u16 amp) 1856 { 1857 const size_t length = ARRAY_SIZE(joycon_rumble_amplitudes); 1858 const struct joycon_rumble_amp_data *data = joycon_rumble_amplitudes; 1859 int i = 0; 1860 1861 if (amp > data[0].amp) { 1862 for (i = 1; i < length - 1; i++) { 1863 if (amp > data[i - 1].amp && amp <= data[i].amp) 1864 break; 1865 } 1866 } 1867 1868 return data[i]; 1869 } 1870 1871 static void joycon_encode_rumble(u8 *data, u16 freq_low, u16 freq_high, u16 amp) 1872 { 1873 struct joycon_rumble_freq_data freq_data_low; 1874 struct joycon_rumble_freq_data freq_data_high; 1875 struct joycon_rumble_amp_data amp_data; 1876 1877 freq_data_low = joycon_find_rumble_freq(freq_low); 1878 freq_data_high = joycon_find_rumble_freq(freq_high); 1879 amp_data = joycon_find_rumble_amp(amp); 1880 1881 data[0] = (freq_data_high.high >> 8) & 0xFF; 1882 data[1] = (freq_data_high.high & 0xFF) + amp_data.high; 1883 data[2] = freq_data_low.low + ((amp_data.low >> 8) & 0xFF); 1884 data[3] = amp_data.low & 0xFF; 1885 } 1886 1887 static const u16 JOYCON_MAX_RUMBLE_HIGH_FREQ = 1253; 1888 static const u16 JOYCON_MIN_RUMBLE_HIGH_FREQ = 82; 1889 static const u16 JOYCON_MAX_RUMBLE_LOW_FREQ = 626; 1890 static const u16 JOYCON_MIN_RUMBLE_LOW_FREQ = 41; 1891 1892 static void joycon_clamp_rumble_freqs(struct joycon_ctlr *ctlr) 1893 { 1894 unsigned long flags; 1895 1896 spin_lock_irqsave(&ctlr->lock, flags); 1897 ctlr->rumble_ll_freq = clamp(ctlr->rumble_ll_freq, 1898 JOYCON_MIN_RUMBLE_LOW_FREQ, 1899 JOYCON_MAX_RUMBLE_LOW_FREQ); 1900 ctlr->rumble_lh_freq = clamp(ctlr->rumble_lh_freq, 1901 JOYCON_MIN_RUMBLE_HIGH_FREQ, 1902 JOYCON_MAX_RUMBLE_HIGH_FREQ); 1903 ctlr->rumble_rl_freq = clamp(ctlr->rumble_rl_freq, 1904 JOYCON_MIN_RUMBLE_LOW_FREQ, 1905 JOYCON_MAX_RUMBLE_LOW_FREQ); 1906 ctlr->rumble_rh_freq = clamp(ctlr->rumble_rh_freq, 1907 JOYCON_MIN_RUMBLE_HIGH_FREQ, 1908 JOYCON_MAX_RUMBLE_HIGH_FREQ); 1909 spin_unlock_irqrestore(&ctlr->lock, flags); 1910 } 1911 1912 static int joycon_set_rumble(struct joycon_ctlr *ctlr, u16 amp_r, u16 amp_l, 1913 bool schedule_now) 1914 { 1915 u8 data[JC_RUMBLE_DATA_SIZE]; 1916 u16 amp; 1917 u16 freq_r_low; 1918 u16 freq_r_high; 1919 u16 freq_l_low; 1920 u16 freq_l_high; 1921 unsigned long flags; 1922 int next_rq_head; 1923 1924 spin_lock_irqsave(&ctlr->lock, flags); 1925 freq_r_low = ctlr->rumble_rl_freq; 1926 freq_r_high = ctlr->rumble_rh_freq; 1927 freq_l_low = ctlr->rumble_ll_freq; 1928 freq_l_high = ctlr->rumble_lh_freq; 1929 /* limit number of silent rumble packets to reduce traffic */ 1930 if (amp_l != 0 || amp_r != 0) 1931 ctlr->rumble_zero_countdown = JC_RUMBLE_ZERO_AMP_PKT_CNT; 1932 spin_unlock_irqrestore(&ctlr->lock, flags); 1933 1934 /* right joy-con */ 1935 amp = amp_r * (u32)joycon_max_rumble_amp / 65535; 1936 joycon_encode_rumble(data + 4, freq_r_low, freq_r_high, amp); 1937 1938 /* left joy-con */ 1939 amp = amp_l * (u32)joycon_max_rumble_amp / 65535; 1940 joycon_encode_rumble(data, freq_l_low, freq_l_high, amp); 1941 1942 spin_lock_irqsave(&ctlr->lock, flags); 1943 1944 next_rq_head = ctlr->rumble_queue_head + 1; 1945 if (next_rq_head >= JC_RUMBLE_QUEUE_SIZE) 1946 next_rq_head = 0; 1947 1948 /* Did we overrun the circular buffer? 1949 * If so, be sure we keep the latest intended rumble state. 1950 */ 1951 if (next_rq_head == ctlr->rumble_queue_tail) { 1952 hid_dbg(ctlr->hdev, "rumble queue is full"); 1953 /* overwrite the prior value at the end of the circular buf */ 1954 next_rq_head = ctlr->rumble_queue_head; 1955 } 1956 1957 ctlr->rumble_queue_head = next_rq_head; 1958 memcpy(ctlr->rumble_data[ctlr->rumble_queue_head], data, 1959 JC_RUMBLE_DATA_SIZE); 1960 1961 /* don't wait for the periodic send (reduces latency) */ 1962 if (schedule_now && ctlr->ctlr_state != JOYCON_CTLR_STATE_REMOVED) 1963 queue_work(ctlr->rumble_queue, &ctlr->rumble_worker); 1964 1965 spin_unlock_irqrestore(&ctlr->lock, flags); 1966 1967 return 0; 1968 } 1969 1970 static int joycon_play_effect(struct input_dev *dev, void *data, 1971 struct ff_effect *effect) 1972 { 1973 struct joycon_ctlr *ctlr = input_get_drvdata(dev); 1974 1975 if (effect->type != FF_RUMBLE) 1976 return 0; 1977 1978 return joycon_set_rumble(ctlr, 1979 effect->u.rumble.weak_magnitude, 1980 effect->u.rumble.strong_magnitude, 1981 true); 1982 } 1983 #endif /* IS_ENABLED(CONFIG_NINTENDO_FF) */ 1984 1985 static void joycon_config_left_stick(struct input_dev *idev) 1986 { 1987 input_set_abs_params(idev, 1988 ABS_X, 1989 -JC_MAX_STICK_MAG, 1990 JC_MAX_STICK_MAG, 1991 JC_STICK_FUZZ, 1992 JC_STICK_FLAT); 1993 input_set_abs_params(idev, 1994 ABS_Y, 1995 -JC_MAX_STICK_MAG, 1996 JC_MAX_STICK_MAG, 1997 JC_STICK_FUZZ, 1998 JC_STICK_FLAT); 1999 } 2000 2001 static void joycon_config_right_stick(struct input_dev *idev) 2002 { 2003 input_set_abs_params(idev, 2004 ABS_RX, 2005 -JC_MAX_STICK_MAG, 2006 JC_MAX_STICK_MAG, 2007 JC_STICK_FUZZ, 2008 JC_STICK_FLAT); 2009 input_set_abs_params(idev, 2010 ABS_RY, 2011 -JC_MAX_STICK_MAG, 2012 JC_MAX_STICK_MAG, 2013 JC_STICK_FUZZ, 2014 JC_STICK_FLAT); 2015 } 2016 2017 static void joycon_config_dpad(struct input_dev *idev) 2018 { 2019 input_set_abs_params(idev, 2020 ABS_HAT0X, 2021 -JC_MAX_DPAD_MAG, 2022 JC_MAX_DPAD_MAG, 2023 JC_DPAD_FUZZ, 2024 JC_DPAD_FLAT); 2025 input_set_abs_params(idev, 2026 ABS_HAT0Y, 2027 -JC_MAX_DPAD_MAG, 2028 JC_MAX_DPAD_MAG, 2029 JC_DPAD_FUZZ, 2030 JC_DPAD_FLAT); 2031 } 2032 2033 static void joycon_config_buttons(struct input_dev *idev, 2034 const struct joycon_ctlr_button_mapping button_mappings[]) 2035 { 2036 const struct joycon_ctlr_button_mapping *button; 2037 2038 for (button = button_mappings; button->code; button++) 2039 input_set_capability(idev, EV_KEY, button->code); 2040 } 2041 2042 static void joycon_config_rumble(struct joycon_ctlr *ctlr) 2043 { 2044 #if IS_ENABLED(CONFIG_NINTENDO_FF) 2045 /* set up rumble */ 2046 input_set_capability(ctlr->input, EV_FF, FF_RUMBLE); 2047 input_ff_create_memless(ctlr->input, NULL, joycon_play_effect); 2048 ctlr->rumble_ll_freq = JC_RUMBLE_DFLT_LOW_FREQ; 2049 ctlr->rumble_lh_freq = JC_RUMBLE_DFLT_HIGH_FREQ; 2050 ctlr->rumble_rl_freq = JC_RUMBLE_DFLT_LOW_FREQ; 2051 ctlr->rumble_rh_freq = JC_RUMBLE_DFLT_HIGH_FREQ; 2052 joycon_clamp_rumble_freqs(ctlr); 2053 joycon_set_rumble(ctlr, 0, 0, false); 2054 ctlr->rumble_msecs = jiffies_to_msecs(jiffies); 2055 #endif 2056 } 2057 2058 static int joycon_imu_input_create(struct joycon_ctlr *ctlr) 2059 { 2060 struct hid_device *hdev; 2061 const char *imu_name; 2062 int ret; 2063 2064 hdev = ctlr->hdev; 2065 2066 /* configure the imu input device */ 2067 ctlr->imu_input = devm_input_allocate_device(&hdev->dev); 2068 if (!ctlr->imu_input) 2069 return -ENOMEM; 2070 2071 ctlr->imu_input->id.bustype = hdev->bus; 2072 ctlr->imu_input->id.vendor = hdev->vendor; 2073 ctlr->imu_input->id.product = hdev->product; 2074 ctlr->imu_input->id.version = hdev->version; 2075 ctlr->imu_input->uniq = ctlr->mac_addr_str; 2076 ctlr->imu_input->phys = hdev->phys; 2077 2078 imu_name = devm_kasprintf(&hdev->dev, GFP_KERNEL, "%s (IMU)", ctlr->input->name); 2079 if (!imu_name) 2080 return -ENOMEM; 2081 2082 ctlr->imu_input->name = imu_name; 2083 2084 input_set_drvdata(ctlr->imu_input, ctlr); 2085 2086 /* configure imu axes */ 2087 input_set_abs_params(ctlr->imu_input, ABS_X, 2088 -JC_IMU_MAX_ACCEL_MAG, JC_IMU_MAX_ACCEL_MAG, 2089 JC_IMU_ACCEL_FUZZ, JC_IMU_ACCEL_FLAT); 2090 input_set_abs_params(ctlr->imu_input, ABS_Y, 2091 -JC_IMU_MAX_ACCEL_MAG, JC_IMU_MAX_ACCEL_MAG, 2092 JC_IMU_ACCEL_FUZZ, JC_IMU_ACCEL_FLAT); 2093 input_set_abs_params(ctlr->imu_input, ABS_Z, 2094 -JC_IMU_MAX_ACCEL_MAG, JC_IMU_MAX_ACCEL_MAG, 2095 JC_IMU_ACCEL_FUZZ, JC_IMU_ACCEL_FLAT); 2096 input_abs_set_res(ctlr->imu_input, ABS_X, JC_IMU_ACCEL_RES_PER_G); 2097 input_abs_set_res(ctlr->imu_input, ABS_Y, JC_IMU_ACCEL_RES_PER_G); 2098 input_abs_set_res(ctlr->imu_input, ABS_Z, JC_IMU_ACCEL_RES_PER_G); 2099 2100 input_set_abs_params(ctlr->imu_input, ABS_RX, 2101 -JC_IMU_MAX_GYRO_MAG, JC_IMU_MAX_GYRO_MAG, 2102 JC_IMU_GYRO_FUZZ, JC_IMU_GYRO_FLAT); 2103 input_set_abs_params(ctlr->imu_input, ABS_RY, 2104 -JC_IMU_MAX_GYRO_MAG, JC_IMU_MAX_GYRO_MAG, 2105 JC_IMU_GYRO_FUZZ, JC_IMU_GYRO_FLAT); 2106 input_set_abs_params(ctlr->imu_input, ABS_RZ, 2107 -JC_IMU_MAX_GYRO_MAG, JC_IMU_MAX_GYRO_MAG, 2108 JC_IMU_GYRO_FUZZ, JC_IMU_GYRO_FLAT); 2109 2110 input_abs_set_res(ctlr->imu_input, ABS_RX, JC_IMU_GYRO_RES_PER_DPS); 2111 input_abs_set_res(ctlr->imu_input, ABS_RY, JC_IMU_GYRO_RES_PER_DPS); 2112 input_abs_set_res(ctlr->imu_input, ABS_RZ, JC_IMU_GYRO_RES_PER_DPS); 2113 2114 __set_bit(EV_MSC, ctlr->imu_input->evbit); 2115 __set_bit(MSC_TIMESTAMP, ctlr->imu_input->mscbit); 2116 __set_bit(INPUT_PROP_ACCELEROMETER, ctlr->imu_input->propbit); 2117 2118 ret = input_register_device(ctlr->imu_input); 2119 if (ret) 2120 return ret; 2121 2122 return 0; 2123 } 2124 2125 static int joycon_input_create(struct joycon_ctlr *ctlr) 2126 { 2127 struct hid_device *hdev; 2128 int ret; 2129 2130 hdev = ctlr->hdev; 2131 2132 ctlr->input = devm_input_allocate_device(&hdev->dev); 2133 if (!ctlr->input) 2134 return -ENOMEM; 2135 ctlr->input->id.bustype = hdev->bus; 2136 ctlr->input->id.vendor = hdev->vendor; 2137 ctlr->input->id.product = hdev->product; 2138 ctlr->input->id.version = hdev->version; 2139 ctlr->input->uniq = ctlr->mac_addr_str; 2140 ctlr->input->name = hdev->name; 2141 ctlr->input->phys = hdev->phys; 2142 input_set_drvdata(ctlr->input, ctlr); 2143 2144 ret = input_register_device(ctlr->input); 2145 if (ret) 2146 return ret; 2147 2148 if (joycon_type_is_right_joycon(ctlr)) { 2149 joycon_config_right_stick(ctlr->input); 2150 joycon_config_buttons(ctlr->input, right_joycon_button_mappings); 2151 if (!joycon_device_is_chrggrip(ctlr)) 2152 joycon_config_buttons(ctlr->input, right_joycon_s_button_mappings); 2153 } else if (joycon_type_is_left_joycon(ctlr)) { 2154 joycon_config_left_stick(ctlr->input); 2155 joycon_config_buttons(ctlr->input, left_joycon_button_mappings); 2156 if (!joycon_device_is_chrggrip(ctlr)) 2157 joycon_config_buttons(ctlr->input, left_joycon_s_button_mappings); 2158 } else if (joycon_type_is_procon(ctlr)) { 2159 joycon_config_left_stick(ctlr->input); 2160 joycon_config_right_stick(ctlr->input); 2161 joycon_config_dpad(ctlr->input); 2162 joycon_config_buttons(ctlr->input, procon_button_mappings); 2163 } else if (joycon_type_is_any_nescon(ctlr)) { 2164 joycon_config_dpad(ctlr->input); 2165 joycon_config_buttons(ctlr->input, nescon_button_mappings); 2166 } else if (joycon_type_is_snescon(ctlr)) { 2167 joycon_config_dpad(ctlr->input); 2168 joycon_config_buttons(ctlr->input, snescon_button_mappings); 2169 } else if (joycon_type_is_gencon(ctlr)) { 2170 joycon_config_dpad(ctlr->input); 2171 joycon_config_buttons(ctlr->input, gencon_button_mappings); 2172 } else if (joycon_type_is_n64con(ctlr)) { 2173 joycon_config_dpad(ctlr->input); 2174 joycon_config_left_stick(ctlr->input); 2175 joycon_config_buttons(ctlr->input, n64con_button_mappings); 2176 } 2177 2178 if (joycon_has_imu(ctlr)) { 2179 ret = joycon_imu_input_create(ctlr); 2180 if (ret) 2181 return ret; 2182 } 2183 2184 if (joycon_has_rumble(ctlr)) 2185 joycon_config_rumble(ctlr); 2186 2187 return 0; 2188 } 2189 2190 /* Because the subcommand sets all the leds at once, the brightness argument is ignored */ 2191 static int joycon_player_led_brightness_set(struct led_classdev *led, 2192 enum led_brightness brightness) 2193 { 2194 struct device *dev = led->dev->parent; 2195 struct hid_device *hdev = to_hid_device(dev); 2196 struct joycon_ctlr *ctlr; 2197 int val = 0; 2198 int i; 2199 int ret; 2200 2201 ctlr = hid_get_drvdata(hdev); 2202 if (!ctlr) { 2203 hid_err(hdev, "No controller data\n"); 2204 return -ENODEV; 2205 } 2206 2207 for (i = 0; i < JC_NUM_LEDS; i++) 2208 val |= ctlr->leds[i].brightness << i; 2209 2210 mutex_lock(&ctlr->output_mutex); 2211 ret = joycon_set_player_leds(ctlr, 0, val); 2212 mutex_unlock(&ctlr->output_mutex); 2213 2214 return ret; 2215 } 2216 2217 static int joycon_home_led_brightness_set(struct led_classdev *led, 2218 enum led_brightness brightness) 2219 { 2220 struct device *dev = led->dev->parent; 2221 struct hid_device *hdev = to_hid_device(dev); 2222 struct joycon_ctlr *ctlr; 2223 int ret; 2224 2225 ctlr = hid_get_drvdata(hdev); 2226 if (!ctlr) { 2227 hid_err(hdev, "No controller data\n"); 2228 return -ENODEV; 2229 } 2230 mutex_lock(&ctlr->output_mutex); 2231 ret = joycon_set_home_led(ctlr, brightness); 2232 mutex_unlock(&ctlr->output_mutex); 2233 return ret; 2234 } 2235 2236 static DEFINE_IDA(nintendo_player_id_allocator); 2237 2238 static int joycon_leds_create(struct joycon_ctlr *ctlr) 2239 { 2240 struct hid_device *hdev = ctlr->hdev; 2241 struct device *dev = &hdev->dev; 2242 const char *d_name = dev_name(dev); 2243 struct led_classdev *led; 2244 int led_val = 0; 2245 char *name; 2246 int ret; 2247 int i; 2248 int player_led_pattern; 2249 2250 /* configure the player LEDs */ 2251 ctlr->player_id = U32_MAX; 2252 ret = ida_alloc(&nintendo_player_id_allocator, GFP_KERNEL); 2253 if (ret < 0) { 2254 hid_warn(hdev, "Failed to allocate player ID, skipping; ret=%d\n", ret); 2255 goto home_led; 2256 } 2257 ctlr->player_id = ret; 2258 player_led_pattern = ret % JC_NUM_LED_PATTERNS; 2259 hid_info(ctlr->hdev, "assigned player %d led pattern", player_led_pattern + 1); 2260 2261 for (i = 0; i < JC_NUM_LEDS; i++) { 2262 name = devm_kasprintf(dev, GFP_KERNEL, "%s:%s:%s", 2263 d_name, 2264 "green", 2265 joycon_player_led_names[i]); 2266 if (!name) 2267 return -ENOMEM; 2268 2269 led = &ctlr->leds[i]; 2270 led->name = name; 2271 led->brightness = joycon_player_led_patterns[player_led_pattern][i]; 2272 led->max_brightness = 1; 2273 led->brightness_set_blocking = 2274 joycon_player_led_brightness_set; 2275 led->flags = LED_CORE_SUSPENDRESUME | LED_HW_PLUGGABLE; 2276 2277 led_val |= joycon_player_led_patterns[player_led_pattern][i] << i; 2278 } 2279 mutex_lock(&ctlr->output_mutex); 2280 ret = joycon_set_player_leds(ctlr, 0, led_val); 2281 mutex_unlock(&ctlr->output_mutex); 2282 if (ret) { 2283 hid_warn(hdev, "Failed to set players LEDs, skipping registration; ret=%d\n", ret); 2284 goto home_led; 2285 } 2286 2287 for (i = 0; i < JC_NUM_LEDS; i++) { 2288 led = &ctlr->leds[i]; 2289 ret = devm_led_classdev_register(&hdev->dev, led); 2290 if (ret) { 2291 hid_err(hdev, "Failed to register player %d LED; ret=%d\n", i + 1, ret); 2292 return ret; 2293 } 2294 } 2295 2296 home_led: 2297 /* configure the home LED */ 2298 if (jc_type_has_right(ctlr)) { 2299 name = devm_kasprintf(dev, GFP_KERNEL, "%s:%s:%s", 2300 d_name, 2301 "blue", 2302 LED_FUNCTION_PLAYER5); 2303 if (!name) 2304 return -ENOMEM; 2305 2306 led = &ctlr->home_led; 2307 led->name = name; 2308 led->brightness = 0; 2309 led->max_brightness = 0xF; 2310 led->brightness_set_blocking = joycon_home_led_brightness_set; 2311 led->flags = LED_CORE_SUSPENDRESUME | LED_HW_PLUGGABLE; 2312 2313 /* Set the home LED to 0 as default state */ 2314 mutex_lock(&ctlr->output_mutex); 2315 ret = joycon_set_home_led(ctlr, 0); 2316 mutex_unlock(&ctlr->output_mutex); 2317 if (ret) { 2318 hid_warn(hdev, "Failed to set home LED, skipping registration; ret=%d\n", ret); 2319 return 0; 2320 } 2321 2322 ret = devm_led_classdev_register(&hdev->dev, led); 2323 if (ret) { 2324 hid_err(hdev, "Failed to register home LED; ret=%d\n", ret); 2325 return ret; 2326 } 2327 } 2328 2329 return 0; 2330 } 2331 2332 static int joycon_battery_get_property(struct power_supply *supply, 2333 enum power_supply_property prop, 2334 union power_supply_propval *val) 2335 { 2336 struct joycon_ctlr *ctlr = power_supply_get_drvdata(supply); 2337 unsigned long flags; 2338 int ret = 0; 2339 u8 capacity; 2340 bool charging; 2341 bool powered; 2342 2343 spin_lock_irqsave(&ctlr->lock, flags); 2344 capacity = ctlr->battery_capacity; 2345 charging = ctlr->battery_charging; 2346 powered = ctlr->host_powered; 2347 spin_unlock_irqrestore(&ctlr->lock, flags); 2348 2349 switch (prop) { 2350 case POWER_SUPPLY_PROP_PRESENT: 2351 val->intval = 1; 2352 break; 2353 case POWER_SUPPLY_PROP_SCOPE: 2354 val->intval = POWER_SUPPLY_SCOPE_DEVICE; 2355 break; 2356 case POWER_SUPPLY_PROP_CAPACITY_LEVEL: 2357 val->intval = capacity; 2358 break; 2359 case POWER_SUPPLY_PROP_STATUS: 2360 if (charging) 2361 val->intval = POWER_SUPPLY_STATUS_CHARGING; 2362 else if (capacity == POWER_SUPPLY_CAPACITY_LEVEL_FULL && 2363 powered) 2364 val->intval = POWER_SUPPLY_STATUS_FULL; 2365 else 2366 val->intval = POWER_SUPPLY_STATUS_DISCHARGING; 2367 break; 2368 default: 2369 ret = -EINVAL; 2370 break; 2371 } 2372 return ret; 2373 } 2374 2375 static enum power_supply_property joycon_battery_props[] = { 2376 POWER_SUPPLY_PROP_PRESENT, 2377 POWER_SUPPLY_PROP_CAPACITY_LEVEL, 2378 POWER_SUPPLY_PROP_SCOPE, 2379 POWER_SUPPLY_PROP_STATUS, 2380 }; 2381 2382 static int joycon_power_supply_create(struct joycon_ctlr *ctlr) 2383 { 2384 struct hid_device *hdev = ctlr->hdev; 2385 struct power_supply_config supply_config = { .drv_data = ctlr, }; 2386 const char * const name_fmt = "nintendo_switch_controller_battery_%s"; 2387 int ret = 0; 2388 2389 /* Set initially to unknown before receiving first input report */ 2390 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_UNKNOWN; 2391 2392 /* Configure the battery's description */ 2393 ctlr->battery_desc.properties = joycon_battery_props; 2394 ctlr->battery_desc.num_properties = 2395 ARRAY_SIZE(joycon_battery_props); 2396 ctlr->battery_desc.get_property = joycon_battery_get_property; 2397 ctlr->battery_desc.type = POWER_SUPPLY_TYPE_BATTERY; 2398 ctlr->battery_desc.use_for_apm = 0; 2399 ctlr->battery_desc.name = devm_kasprintf(&hdev->dev, GFP_KERNEL, 2400 name_fmt, 2401 dev_name(&hdev->dev)); 2402 if (!ctlr->battery_desc.name) 2403 return -ENOMEM; 2404 2405 ctlr->battery = devm_power_supply_register(&hdev->dev, 2406 &ctlr->battery_desc, 2407 &supply_config); 2408 if (IS_ERR(ctlr->battery)) { 2409 ret = PTR_ERR(ctlr->battery); 2410 hid_err(hdev, "Failed to register battery; ret=%d\n", ret); 2411 return ret; 2412 } 2413 2414 return power_supply_powers(ctlr->battery, &hdev->dev); 2415 } 2416 2417 static int joycon_read_info(struct joycon_ctlr *ctlr) 2418 { 2419 int ret; 2420 int i; 2421 int j; 2422 struct joycon_subcmd_request req = { 0 }; 2423 struct joycon_input_report *report; 2424 2425 req.subcmd_id = JC_SUBCMD_REQ_DEV_INFO; 2426 ret = joycon_send_subcmd(ctlr, &req, 0, HZ); 2427 if (ret) { 2428 hid_err(ctlr->hdev, "Failed to get joycon info; ret=%d\n", ret); 2429 return ret; 2430 } 2431 2432 report = (struct joycon_input_report *)ctlr->input_buf; 2433 2434 for (i = 4, j = 0; j < 6; i++, j++) 2435 ctlr->mac_addr[j] = report->subcmd_reply.data[i]; 2436 2437 ctlr->mac_addr_str = devm_kasprintf(&ctlr->hdev->dev, GFP_KERNEL, 2438 "%02X:%02X:%02X:%02X:%02X:%02X", 2439 ctlr->mac_addr[0], 2440 ctlr->mac_addr[1], 2441 ctlr->mac_addr[2], 2442 ctlr->mac_addr[3], 2443 ctlr->mac_addr[4], 2444 ctlr->mac_addr[5]); 2445 if (!ctlr->mac_addr_str) 2446 return -ENOMEM; 2447 hid_info(ctlr->hdev, "controller MAC = %s\n", ctlr->mac_addr_str); 2448 2449 /* 2450 * Retrieve the type so we can distinguish the controller type 2451 * Unfortantly the hdev->product can't always be used due to a ?bug? 2452 * with the NSO Genesis controller. Over USB, it will report the 2453 * PID as 0x201E, but over bluetooth it will report the PID as 0x2017 2454 * which is the same as the NSO SNES controller. This is different from 2455 * the rest of the controllers which will report the same PID over USB 2456 * and bluetooth. 2457 */ 2458 ctlr->ctlr_type = report->subcmd_reply.data[2]; 2459 hid_dbg(ctlr->hdev, "controller type = 0x%02X\n", ctlr->ctlr_type); 2460 2461 return 0; 2462 } 2463 2464 static int joycon_init(struct hid_device *hdev) 2465 { 2466 struct joycon_ctlr *ctlr = hid_get_drvdata(hdev); 2467 int ret = 0; 2468 2469 mutex_lock(&ctlr->output_mutex); 2470 /* if handshake command fails, assume ble pro controller */ 2471 if (joycon_using_usb(ctlr) && !joycon_send_usb(ctlr, JC_USB_CMD_HANDSHAKE, HZ)) { 2472 hid_dbg(hdev, "detected USB controller\n"); 2473 /* set baudrate for improved latency */ 2474 ret = joycon_send_usb(ctlr, JC_USB_CMD_BAUDRATE_3M, HZ); 2475 if (ret) { 2476 /* 2477 * We can function with the default baudrate. 2478 * Provide a warning, and continue on. 2479 */ 2480 hid_warn(hdev, "Failed to set baudrate (ret=%d), continuing anyway\n", ret); 2481 } 2482 /* handshake */ 2483 ret = joycon_send_usb(ctlr, JC_USB_CMD_HANDSHAKE, HZ); 2484 if (ret) { 2485 hid_err(hdev, "Failed handshake; ret=%d\n", ret); 2486 goto out_unlock; 2487 } 2488 /* 2489 * Set no timeout (to keep controller in USB mode). 2490 * This doesn't send a response, so ignore the timeout. 2491 */ 2492 joycon_send_usb(ctlr, JC_USB_CMD_NO_TIMEOUT, HZ/10); 2493 } else if (jc_type_is_chrggrip(ctlr)) { 2494 hid_err(hdev, "Failed charging grip handshake\n"); 2495 ret = -ETIMEDOUT; 2496 goto out_unlock; 2497 } 2498 2499 /* needed to retrieve the controller type */ 2500 ret = joycon_read_info(ctlr); 2501 if (ret) { 2502 hid_err(hdev, "Failed to retrieve controller info; ret=%d\n", 2503 ret); 2504 goto out_unlock; 2505 } 2506 2507 if (joycon_has_joysticks(ctlr)) { 2508 /* get controller calibration data, and parse it */ 2509 ret = joycon_request_calibration(ctlr); 2510 if (ret) { 2511 /* 2512 * We can function with default calibration, but it may be 2513 * inaccurate. Provide a warning, and continue on. 2514 */ 2515 hid_warn(hdev, "Analog stick positions may be inaccurate\n"); 2516 } 2517 } 2518 2519 if (joycon_has_imu(ctlr)) { 2520 /* get IMU calibration data, and parse it */ 2521 ret = joycon_request_imu_calibration(ctlr); 2522 if (ret) { 2523 /* 2524 * We can function with default calibration, but it may be 2525 * inaccurate. Provide a warning, and continue on. 2526 */ 2527 hid_warn(hdev, "Unable to read IMU calibration data\n"); 2528 } 2529 2530 /* Enable the IMU */ 2531 ret = joycon_enable_imu(ctlr); 2532 if (ret) { 2533 hid_err(hdev, "Failed to enable the IMU; ret=%d\n", ret); 2534 goto out_unlock; 2535 } 2536 } 2537 2538 /* Set the reporting mode to 0x30, which is the full report mode */ 2539 ret = joycon_set_report_mode(ctlr); 2540 if (ret) { 2541 hid_err(hdev, "Failed to set report mode; ret=%d\n", ret); 2542 goto out_unlock; 2543 } 2544 2545 if (joycon_has_rumble(ctlr)) { 2546 /* Enable rumble */ 2547 ret = joycon_enable_rumble(ctlr); 2548 if (ret) { 2549 hid_err(hdev, "Failed to enable rumble; ret=%d\n", ret); 2550 goto out_unlock; 2551 } 2552 } 2553 2554 out_unlock: 2555 mutex_unlock(&ctlr->output_mutex); 2556 return ret; 2557 } 2558 2559 /* Common handler for parsing inputs */ 2560 static int joycon_ctlr_read_handler(struct joycon_ctlr *ctlr, u8 *data, 2561 int size) 2562 { 2563 if (data[0] == JC_INPUT_SUBCMD_REPLY || data[0] == JC_INPUT_IMU_DATA || 2564 data[0] == JC_INPUT_MCU_DATA) { 2565 if (size >= 12) /* make sure it contains the input report */ 2566 joycon_parse_report(ctlr, 2567 (struct joycon_input_report *)data); 2568 } 2569 2570 return 0; 2571 } 2572 2573 static int joycon_ctlr_handle_event(struct joycon_ctlr *ctlr, u8 *data, 2574 int size) 2575 { 2576 int ret = 0; 2577 bool match = false; 2578 struct joycon_input_report *report; 2579 2580 if (unlikely(mutex_is_locked(&ctlr->output_mutex)) && 2581 ctlr->msg_type != JOYCON_MSG_TYPE_NONE) { 2582 switch (ctlr->msg_type) { 2583 case JOYCON_MSG_TYPE_USB: 2584 if (size < 2) 2585 break; 2586 if (data[0] == JC_INPUT_USB_RESPONSE && 2587 data[1] == ctlr->usb_ack_match) 2588 match = true; 2589 break; 2590 case JOYCON_MSG_TYPE_SUBCMD: 2591 if (size < sizeof(struct joycon_input_report) || 2592 data[0] != JC_INPUT_SUBCMD_REPLY) 2593 break; 2594 report = (struct joycon_input_report *)data; 2595 if (report->subcmd_reply.id == ctlr->subcmd_ack_match) 2596 match = true; 2597 break; 2598 default: 2599 break; 2600 } 2601 2602 if (match) { 2603 memcpy(ctlr->input_buf, data, 2604 min(size, (int)JC_MAX_RESP_SIZE)); 2605 ctlr->msg_type = JOYCON_MSG_TYPE_NONE; 2606 ctlr->received_resp = true; 2607 wake_up(&ctlr->wait); 2608 2609 /* This message has been handled */ 2610 return 1; 2611 } 2612 } 2613 2614 if (ctlr->ctlr_state == JOYCON_CTLR_STATE_READ) 2615 ret = joycon_ctlr_read_handler(ctlr, data, size); 2616 2617 return ret; 2618 } 2619 2620 static int nintendo_hid_event(struct hid_device *hdev, 2621 struct hid_report *report, u8 *raw_data, int size) 2622 { 2623 struct joycon_ctlr *ctlr = hid_get_drvdata(hdev); 2624 2625 if (size < 1) 2626 return -EINVAL; 2627 2628 return joycon_ctlr_handle_event(ctlr, raw_data, size); 2629 } 2630 2631 static int nintendo_hid_probe(struct hid_device *hdev, 2632 const struct hid_device_id *id) 2633 { 2634 int ret; 2635 struct joycon_ctlr *ctlr; 2636 2637 hid_dbg(hdev, "probe - start\n"); 2638 2639 ctlr = devm_kzalloc(&hdev->dev, sizeof(*ctlr), GFP_KERNEL); 2640 if (!ctlr) { 2641 ret = -ENOMEM; 2642 goto err; 2643 } 2644 2645 ctlr->hdev = hdev; 2646 ctlr->ctlr_state = JOYCON_CTLR_STATE_INIT; 2647 ctlr->rumble_queue_head = 0; 2648 ctlr->rumble_queue_tail = 0; 2649 hid_set_drvdata(hdev, ctlr); 2650 mutex_init(&ctlr->output_mutex); 2651 init_waitqueue_head(&ctlr->wait); 2652 spin_lock_init(&ctlr->lock); 2653 ctlr->rumble_queue = alloc_workqueue("hid-nintendo-rumble_wq", 2654 WQ_FREEZABLE | WQ_MEM_RECLAIM, 0); 2655 if (!ctlr->rumble_queue) { 2656 ret = -ENOMEM; 2657 goto err; 2658 } 2659 INIT_WORK(&ctlr->rumble_worker, joycon_rumble_worker); 2660 2661 ret = hid_parse(hdev); 2662 if (ret) { 2663 hid_err(hdev, "HID parse failed\n"); 2664 goto err_wq; 2665 } 2666 2667 /* 2668 * Patch the hw version of pro controller/joycons, so applications can 2669 * distinguish between the default HID mappings and the mappings defined 2670 * by the Linux game controller spec. This is important for the SDL2 2671 * library, which has a game controller database, which uses device ids 2672 * in combination with version as a key. 2673 */ 2674 hdev->version |= 0x8000; 2675 2676 ret = hid_hw_start(hdev, HID_CONNECT_HIDRAW); 2677 if (ret) { 2678 hid_err(hdev, "HW start failed\n"); 2679 goto err_wq; 2680 } 2681 2682 ret = hid_hw_open(hdev); 2683 if (ret) { 2684 hid_err(hdev, "cannot start hardware I/O\n"); 2685 goto err_stop; 2686 } 2687 2688 hid_device_io_start(hdev); 2689 2690 ret = joycon_init(hdev); 2691 if (ret) { 2692 hid_err(hdev, "Failed to initialize controller; ret=%d\n", ret); 2693 goto err_close; 2694 } 2695 2696 /* Initialize the leds */ 2697 ret = joycon_leds_create(ctlr); 2698 if (ret) { 2699 hid_err(hdev, "Failed to create leds; ret=%d\n", ret); 2700 goto err_close; 2701 } 2702 2703 /* Initialize the battery power supply */ 2704 ret = joycon_power_supply_create(ctlr); 2705 if (ret) { 2706 hid_err(hdev, "Failed to create power_supply; ret=%d\n", ret); 2707 goto err_ida; 2708 } 2709 2710 ret = joycon_input_create(ctlr); 2711 if (ret) { 2712 hid_err(hdev, "Failed to create input device; ret=%d\n", ret); 2713 goto err_ida; 2714 } 2715 2716 ctlr->ctlr_state = JOYCON_CTLR_STATE_READ; 2717 2718 hid_dbg(hdev, "probe - success\n"); 2719 return 0; 2720 2721 err_ida: 2722 ida_free(&nintendo_player_id_allocator, ctlr->player_id); 2723 err_close: 2724 hid_hw_close(hdev); 2725 err_stop: 2726 hid_hw_stop(hdev); 2727 err_wq: 2728 destroy_workqueue(ctlr->rumble_queue); 2729 err: 2730 hid_err(hdev, "probe - fail = %d\n", ret); 2731 return ret; 2732 } 2733 2734 static void nintendo_hid_remove(struct hid_device *hdev) 2735 { 2736 struct joycon_ctlr *ctlr = hid_get_drvdata(hdev); 2737 unsigned long flags; 2738 2739 hid_dbg(hdev, "remove\n"); 2740 2741 /* Prevent further attempts at sending subcommands. */ 2742 spin_lock_irqsave(&ctlr->lock, flags); 2743 ctlr->ctlr_state = JOYCON_CTLR_STATE_REMOVED; 2744 spin_unlock_irqrestore(&ctlr->lock, flags); 2745 2746 destroy_workqueue(ctlr->rumble_queue); 2747 ida_free(&nintendo_player_id_allocator, ctlr->player_id); 2748 2749 hid_hw_close(hdev); 2750 hid_hw_stop(hdev); 2751 } 2752 2753 #ifdef CONFIG_PM 2754 2755 static int nintendo_hid_resume(struct hid_device *hdev) 2756 { 2757 int ret = joycon_init(hdev); 2758 2759 if (ret) 2760 hid_err(hdev, "Failed to restore controller after resume"); 2761 2762 return ret; 2763 } 2764 2765 #endif 2766 2767 static const struct hid_device_id nintendo_hid_devices[] = { 2768 { HID_USB_DEVICE(USB_VENDOR_ID_NINTENDO, 2769 USB_DEVICE_ID_NINTENDO_PROCON) }, 2770 { HID_USB_DEVICE(USB_VENDOR_ID_NINTENDO, 2771 USB_DEVICE_ID_NINTENDO_SNESCON) }, 2772 { HID_USB_DEVICE(USB_VENDOR_ID_NINTENDO, 2773 USB_DEVICE_ID_NINTENDO_GENCON) }, 2774 { HID_USB_DEVICE(USB_VENDOR_ID_NINTENDO, 2775 USB_DEVICE_ID_NINTENDO_N64CON) }, 2776 { HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_NINTENDO, 2777 USB_DEVICE_ID_NINTENDO_PROCON) }, 2778 { HID_USB_DEVICE(USB_VENDOR_ID_NINTENDO, 2779 USB_DEVICE_ID_NINTENDO_CHRGGRIP) }, 2780 { HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_NINTENDO, 2781 USB_DEVICE_ID_NINTENDO_JOYCONL) }, 2782 { HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_NINTENDO, 2783 USB_DEVICE_ID_NINTENDO_JOYCONR) }, 2784 { HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_NINTENDO, 2785 USB_DEVICE_ID_NINTENDO_SNESCON) }, 2786 { HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_NINTENDO, 2787 USB_DEVICE_ID_NINTENDO_GENCON) }, 2788 { HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_NINTENDO, 2789 USB_DEVICE_ID_NINTENDO_N64CON) }, 2790 { } 2791 }; 2792 MODULE_DEVICE_TABLE(hid, nintendo_hid_devices); 2793 2794 static struct hid_driver nintendo_hid_driver = { 2795 .name = "nintendo", 2796 .id_table = nintendo_hid_devices, 2797 .probe = nintendo_hid_probe, 2798 .remove = nintendo_hid_remove, 2799 .raw_event = nintendo_hid_event, 2800 2801 #ifdef CONFIG_PM 2802 .resume = nintendo_hid_resume, 2803 #endif 2804 }; 2805 static int __init nintendo_init(void) 2806 { 2807 return hid_register_driver(&nintendo_hid_driver); 2808 } 2809 2810 static void __exit nintendo_exit(void) 2811 { 2812 hid_unregister_driver(&nintendo_hid_driver); 2813 ida_destroy(&nintendo_player_id_allocator); 2814 } 2815 2816 module_init(nintendo_init); 2817 module_exit(nintendo_exit); 2818 2819 MODULE_LICENSE("GPL"); 2820 MODULE_AUTHOR("Ryan McClelland <rymcclel@gmail.com>"); 2821 MODULE_AUTHOR("Emily Strickland <linux@emily.st>"); 2822 MODULE_AUTHOR("Daniel J. Ogorchock <djogorchock@gmail.com>"); 2823 MODULE_DESCRIPTION("Driver for Nintendo Switch Controllers"); 2824