1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Copyright © 2019-2020 Intel Corporation 4 */ 5 6 #include <linux/clk.h> 7 #include <linux/delay.h> 8 #include <linux/of_graph.h> 9 #include <linux/mfd/syscon.h> 10 #include <linux/platform_device.h> 11 #include <linux/regmap.h> 12 13 #include <drm/drm_atomic_helper.h> 14 #include <drm/drm_bridge.h> 15 #include <drm/drm_bridge_connector.h> 16 #include <drm/drm_mipi_dsi.h> 17 #include <drm/drm_simple_kms_helper.h> 18 #include <drm/drm_print.h> 19 #include <drm/drm_probe_helper.h> 20 21 #include "kmb_dsi.h" 22 #include "kmb_regs.h" 23 24 static struct mipi_dsi_host *dsi_host; 25 static struct mipi_dsi_device *dsi_device; 26 static struct drm_bridge *adv_bridge; 27 28 /* Default setting is 1080p, 4 lanes */ 29 #define IMG_HEIGHT_LINES 1080 30 #define IMG_WIDTH_PX 1920 31 #define MIPI_TX_ACTIVE_LANES 4 32 33 static struct mipi_tx_frame_section_cfg mipi_tx_frame0_sect_cfg = { 34 .width_pixels = IMG_WIDTH_PX, 35 .height_lines = IMG_HEIGHT_LINES, 36 .data_type = DSI_LP_DT_PPS_RGB888_24B, 37 .data_mode = MIPI_DATA_MODE1, 38 .dma_packed = 0 39 }; 40 41 static struct mipi_tx_frame_cfg mipitx_frame0_cfg = { 42 .sections[0] = &mipi_tx_frame0_sect_cfg, 43 .sections[1] = NULL, 44 .sections[2] = NULL, 45 .sections[3] = NULL, 46 .vsync_width = 5, 47 .v_backporch = 36, 48 .v_frontporch = 4, 49 .hsync_width = 44, 50 .h_backporch = 148, 51 .h_frontporch = 88 52 }; 53 54 static const struct mipi_tx_dsi_cfg mipitx_dsi_cfg = { 55 .hfp_blank_en = 0, 56 .eotp_en = 0, 57 .lpm_last_vfp_line = 0, 58 .lpm_first_vsa_line = 0, 59 .sync_pulse_eventn = DSI_VIDEO_MODE_NO_BURST_EVENT, 60 .hfp_blanking = SEND_BLANK_PACKET, 61 .hbp_blanking = SEND_BLANK_PACKET, 62 .hsa_blanking = SEND_BLANK_PACKET, 63 .v_blanking = SEND_BLANK_PACKET, 64 }; 65 66 static struct mipi_ctrl_cfg mipi_tx_init_cfg = { 67 .active_lanes = MIPI_TX_ACTIVE_LANES, 68 .lane_rate_mbps = MIPI_TX_LANE_DATA_RATE_MBPS, 69 .ref_clk_khz = MIPI_TX_REF_CLK_KHZ, 70 .cfg_clk_khz = MIPI_TX_CFG_CLK_KHZ, 71 .tx_ctrl_cfg = { 72 .frames[0] = &mipitx_frame0_cfg, 73 .frames[1] = NULL, 74 .frames[2] = NULL, 75 .frames[3] = NULL, 76 .tx_dsi_cfg = &mipitx_dsi_cfg, 77 .line_sync_pkt_en = 0, 78 .line_counter_active = 0, 79 .frame_counter_active = 0, 80 .tx_always_use_hact = 1, 81 .tx_hact_wait_stop = 1, 82 } 83 }; 84 85 struct mipi_hs_freq_range_cfg { 86 u16 default_bit_rate_mbps; 87 u8 hsfreqrange_code; 88 }; 89 90 struct vco_params { 91 u32 freq; 92 u32 range; 93 u32 divider; 94 }; 95 96 static const struct vco_params vco_table[] = { 97 {52, 0x3f, 8}, 98 {80, 0x39, 8}, 99 {105, 0x2f, 4}, 100 {160, 0x29, 4}, 101 {210, 0x1f, 2}, 102 {320, 0x19, 2}, 103 {420, 0x0f, 1}, 104 {630, 0x09, 1}, 105 {1100, 0x03, 1}, 106 {0xffff, 0x01, 1}, 107 }; 108 109 static const struct mipi_hs_freq_range_cfg 110 mipi_hs_freq_range[MIPI_DPHY_DEFAULT_BIT_RATES] = { 111 {.default_bit_rate_mbps = 80, .hsfreqrange_code = 0x00}, 112 {.default_bit_rate_mbps = 90, .hsfreqrange_code = 0x10}, 113 {.default_bit_rate_mbps = 100, .hsfreqrange_code = 0x20}, 114 {.default_bit_rate_mbps = 110, .hsfreqrange_code = 0x30}, 115 {.default_bit_rate_mbps = 120, .hsfreqrange_code = 0x01}, 116 {.default_bit_rate_mbps = 130, .hsfreqrange_code = 0x11}, 117 {.default_bit_rate_mbps = 140, .hsfreqrange_code = 0x21}, 118 {.default_bit_rate_mbps = 150, .hsfreqrange_code = 0x31}, 119 {.default_bit_rate_mbps = 160, .hsfreqrange_code = 0x02}, 120 {.default_bit_rate_mbps = 170, .hsfreqrange_code = 0x12}, 121 {.default_bit_rate_mbps = 180, .hsfreqrange_code = 0x22}, 122 {.default_bit_rate_mbps = 190, .hsfreqrange_code = 0x32}, 123 {.default_bit_rate_mbps = 205, .hsfreqrange_code = 0x03}, 124 {.default_bit_rate_mbps = 220, .hsfreqrange_code = 0x13}, 125 {.default_bit_rate_mbps = 235, .hsfreqrange_code = 0x23}, 126 {.default_bit_rate_mbps = 250, .hsfreqrange_code = 0x33}, 127 {.default_bit_rate_mbps = 275, .hsfreqrange_code = 0x04}, 128 {.default_bit_rate_mbps = 300, .hsfreqrange_code = 0x14}, 129 {.default_bit_rate_mbps = 325, .hsfreqrange_code = 0x25}, 130 {.default_bit_rate_mbps = 350, .hsfreqrange_code = 0x35}, 131 {.default_bit_rate_mbps = 400, .hsfreqrange_code = 0x05}, 132 {.default_bit_rate_mbps = 450, .hsfreqrange_code = 0x16}, 133 {.default_bit_rate_mbps = 500, .hsfreqrange_code = 0x26}, 134 {.default_bit_rate_mbps = 550, .hsfreqrange_code = 0x37}, 135 {.default_bit_rate_mbps = 600, .hsfreqrange_code = 0x07}, 136 {.default_bit_rate_mbps = 650, .hsfreqrange_code = 0x18}, 137 {.default_bit_rate_mbps = 700, .hsfreqrange_code = 0x28}, 138 {.default_bit_rate_mbps = 750, .hsfreqrange_code = 0x39}, 139 {.default_bit_rate_mbps = 800, .hsfreqrange_code = 0x09}, 140 {.default_bit_rate_mbps = 850, .hsfreqrange_code = 0x19}, 141 {.default_bit_rate_mbps = 900, .hsfreqrange_code = 0x29}, 142 {.default_bit_rate_mbps = 1000, .hsfreqrange_code = 0x0A}, 143 {.default_bit_rate_mbps = 1050, .hsfreqrange_code = 0x1A}, 144 {.default_bit_rate_mbps = 1100, .hsfreqrange_code = 0x2A}, 145 {.default_bit_rate_mbps = 1150, .hsfreqrange_code = 0x3B}, 146 {.default_bit_rate_mbps = 1200, .hsfreqrange_code = 0x0B}, 147 {.default_bit_rate_mbps = 1250, .hsfreqrange_code = 0x1B}, 148 {.default_bit_rate_mbps = 1300, .hsfreqrange_code = 0x2B}, 149 {.default_bit_rate_mbps = 1350, .hsfreqrange_code = 0x3C}, 150 {.default_bit_rate_mbps = 1400, .hsfreqrange_code = 0x0C}, 151 {.default_bit_rate_mbps = 1450, .hsfreqrange_code = 0x1C}, 152 {.default_bit_rate_mbps = 1500, .hsfreqrange_code = 0x2C}, 153 {.default_bit_rate_mbps = 1550, .hsfreqrange_code = 0x3D}, 154 {.default_bit_rate_mbps = 1600, .hsfreqrange_code = 0x0D}, 155 {.default_bit_rate_mbps = 1650, .hsfreqrange_code = 0x1D}, 156 {.default_bit_rate_mbps = 1700, .hsfreqrange_code = 0x2E}, 157 {.default_bit_rate_mbps = 1750, .hsfreqrange_code = 0x3E}, 158 {.default_bit_rate_mbps = 1800, .hsfreqrange_code = 0x0E}, 159 {.default_bit_rate_mbps = 1850, .hsfreqrange_code = 0x1E}, 160 {.default_bit_rate_mbps = 1900, .hsfreqrange_code = 0x2F}, 161 {.default_bit_rate_mbps = 1950, .hsfreqrange_code = 0x3F}, 162 {.default_bit_rate_mbps = 2000, .hsfreqrange_code = 0x0F}, 163 {.default_bit_rate_mbps = 2050, .hsfreqrange_code = 0x40}, 164 {.default_bit_rate_mbps = 2100, .hsfreqrange_code = 0x41}, 165 {.default_bit_rate_mbps = 2150, .hsfreqrange_code = 0x42}, 166 {.default_bit_rate_mbps = 2200, .hsfreqrange_code = 0x43}, 167 {.default_bit_rate_mbps = 2250, .hsfreqrange_code = 0x44}, 168 {.default_bit_rate_mbps = 2300, .hsfreqrange_code = 0x45}, 169 {.default_bit_rate_mbps = 2350, .hsfreqrange_code = 0x46}, 170 {.default_bit_rate_mbps = 2400, .hsfreqrange_code = 0x47}, 171 {.default_bit_rate_mbps = 2450, .hsfreqrange_code = 0x48}, 172 {.default_bit_rate_mbps = 2500, .hsfreqrange_code = 0x49} 173 }; 174 175 static void kmb_dsi_clk_disable(struct kmb_dsi *kmb_dsi) 176 { 177 clk_disable_unprepare(kmb_dsi->clk_mipi); 178 clk_disable_unprepare(kmb_dsi->clk_mipi_ecfg); 179 clk_disable_unprepare(kmb_dsi->clk_mipi_cfg); 180 } 181 182 void kmb_dsi_host_unregister(struct kmb_dsi *kmb_dsi) 183 { 184 kmb_dsi_clk_disable(kmb_dsi); 185 mipi_dsi_host_unregister(kmb_dsi->host); 186 } 187 188 /* 189 * This DSI can only be paired with bridges that do config through i2c 190 * which is ADV 7535 in the KMB EVM 191 */ 192 static ssize_t kmb_dsi_host_transfer(struct mipi_dsi_host *host, 193 const struct mipi_dsi_msg *msg) 194 { 195 return 0; 196 } 197 198 static int kmb_dsi_host_attach(struct mipi_dsi_host *host, 199 struct mipi_dsi_device *dev) 200 { 201 return 0; 202 } 203 204 static int kmb_dsi_host_detach(struct mipi_dsi_host *host, 205 struct mipi_dsi_device *dev) 206 { 207 return 0; 208 } 209 210 static const struct mipi_dsi_host_ops kmb_dsi_host_ops = { 211 .attach = kmb_dsi_host_attach, 212 .detach = kmb_dsi_host_detach, 213 .transfer = kmb_dsi_host_transfer, 214 }; 215 216 int kmb_dsi_host_bridge_init(struct device *dev) 217 { 218 struct device_node *encoder_node, *dsi_out; 219 220 /* Create and register MIPI DSI host */ 221 if (!dsi_host) { 222 dsi_host = kzalloc(sizeof(*dsi_host), GFP_KERNEL); 223 if (!dsi_host) 224 return -ENOMEM; 225 226 dsi_host->ops = &kmb_dsi_host_ops; 227 228 if (!dsi_device) { 229 dsi_device = kzalloc(sizeof(*dsi_device), GFP_KERNEL); 230 if (!dsi_device) { 231 kfree(dsi_host); 232 return -ENOMEM; 233 } 234 } 235 236 dsi_host->dev = dev; 237 mipi_dsi_host_register(dsi_host); 238 } 239 240 /* Find ADV7535 node and initialize it */ 241 dsi_out = of_graph_get_endpoint_by_regs(dev->of_node, 0, 1); 242 if (!dsi_out) { 243 DRM_ERROR("Failed to get dsi_out node info from DT\n"); 244 return -EINVAL; 245 } 246 encoder_node = of_graph_get_remote_port_parent(dsi_out); 247 if (!encoder_node) { 248 of_node_put(dsi_out); 249 DRM_ERROR("Failed to get bridge info from DT\n"); 250 return -EINVAL; 251 } 252 /* Locate drm bridge from the hdmi encoder DT node */ 253 adv_bridge = of_drm_find_bridge(encoder_node); 254 of_node_put(dsi_out); 255 of_node_put(encoder_node); 256 if (!adv_bridge) { 257 DRM_DEBUG("Wait for external bridge driver DT\n"); 258 return -EPROBE_DEFER; 259 } 260 261 return 0; 262 } 263 264 static u32 mipi_get_datatype_params(u32 data_type, u32 data_mode, 265 struct mipi_data_type_params *params) 266 { 267 struct mipi_data_type_params data_type_param; 268 269 switch (data_type) { 270 case DSI_LP_DT_PPS_YCBCR420_12B: 271 data_type_param.size_constraint_pixels = 2; 272 data_type_param.size_constraint_bytes = 3; 273 switch (data_mode) { 274 /* Case 0 not supported according to MDK */ 275 case 1: 276 case 2: 277 case 3: 278 data_type_param.pixels_per_pclk = 2; 279 data_type_param.bits_per_pclk = 24; 280 break; 281 default: 282 DRM_ERROR("DSI: Invalid data_mode %d\n", data_mode); 283 return -EINVAL; 284 } 285 break; 286 case DSI_LP_DT_PPS_YCBCR422_16B: 287 data_type_param.size_constraint_pixels = 2; 288 data_type_param.size_constraint_bytes = 4; 289 switch (data_mode) { 290 /* Case 0 and 1 not supported according 291 * to MDK 292 */ 293 case 2: 294 data_type_param.pixels_per_pclk = 1; 295 data_type_param.bits_per_pclk = 16; 296 break; 297 case 3: 298 data_type_param.pixels_per_pclk = 2; 299 data_type_param.bits_per_pclk = 32; 300 break; 301 default: 302 DRM_ERROR("DSI: Invalid data_mode %d\n", data_mode); 303 return -EINVAL; 304 } 305 break; 306 case DSI_LP_DT_LPPS_YCBCR422_20B: 307 case DSI_LP_DT_PPS_YCBCR422_24B: 308 data_type_param.size_constraint_pixels = 2; 309 data_type_param.size_constraint_bytes = 6; 310 switch (data_mode) { 311 /* Case 0 not supported according to MDK */ 312 case 1: 313 case 2: 314 case 3: 315 data_type_param.pixels_per_pclk = 1; 316 data_type_param.bits_per_pclk = 24; 317 break; 318 default: 319 DRM_ERROR("DSI: Invalid data_mode %d\n", data_mode); 320 return -EINVAL; 321 } 322 break; 323 case DSI_LP_DT_PPS_RGB565_16B: 324 data_type_param.size_constraint_pixels = 1; 325 data_type_param.size_constraint_bytes = 2; 326 switch (data_mode) { 327 case 0: 328 case 1: 329 data_type_param.pixels_per_pclk = 1; 330 data_type_param.bits_per_pclk = 16; 331 break; 332 case 2: 333 case 3: 334 data_type_param.pixels_per_pclk = 2; 335 data_type_param.bits_per_pclk = 32; 336 break; 337 default: 338 DRM_ERROR("DSI: Invalid data_mode %d\n", data_mode); 339 return -EINVAL; 340 } 341 break; 342 case DSI_LP_DT_PPS_RGB666_18B: 343 data_type_param.size_constraint_pixels = 4; 344 data_type_param.size_constraint_bytes = 9; 345 data_type_param.bits_per_pclk = 18; 346 data_type_param.pixels_per_pclk = 1; 347 break; 348 case DSI_LP_DT_LPPS_RGB666_18B: 349 case DSI_LP_DT_PPS_RGB888_24B: 350 data_type_param.size_constraint_pixels = 1; 351 data_type_param.size_constraint_bytes = 3; 352 data_type_param.bits_per_pclk = 24; 353 data_type_param.pixels_per_pclk = 1; 354 break; 355 case DSI_LP_DT_PPS_RGB101010_30B: 356 data_type_param.size_constraint_pixels = 4; 357 data_type_param.size_constraint_bytes = 15; 358 data_type_param.bits_per_pclk = 30; 359 data_type_param.pixels_per_pclk = 1; 360 break; 361 default: 362 DRM_ERROR("DSI: Invalid data_type %d\n", data_type); 363 return -EINVAL; 364 } 365 366 *params = data_type_param; 367 return 0; 368 } 369 370 static u32 compute_wc(u32 width_px, u8 size_constr_p, u8 size_constr_b) 371 { 372 /* Calculate the word count for each long packet */ 373 return (((width_px / size_constr_p) * size_constr_b) & 0xffff); 374 } 375 376 static u32 compute_unpacked_bytes(u32 wc, u8 bits_per_pclk) 377 { 378 /* Number of PCLK cycles needed to transfer a line 379 * with each PCLK cycle, 4 Bytes are sent through the PPL module 380 */ 381 return ((wc * 8) / bits_per_pclk) * 4; 382 } 383 384 static u32 mipi_tx_fg_section_cfg_regs(struct kmb_dsi *kmb_dsi, 385 u8 frame_id, u8 section, 386 u32 height_lines, u32 unpacked_bytes, 387 struct mipi_tx_frame_sect_phcfg *ph_cfg) 388 { 389 u32 cfg = 0; 390 u32 ctrl_no = MIPI_CTRL6; 391 u32 reg_adr; 392 393 /* Frame section packet header */ 394 /* Word count bits [15:0] */ 395 cfg = (ph_cfg->wc & MIPI_TX_SECT_WC_MASK) << 0; 396 397 /* Data type (bits [21:16]) */ 398 cfg |= ((ph_cfg->data_type & MIPI_TX_SECT_DT_MASK) 399 << MIPI_TX_SECT_DT_SHIFT); 400 401 /* Virtual channel (bits [23:22]) */ 402 cfg |= ((ph_cfg->vchannel & MIPI_TX_SECT_VC_MASK) 403 << MIPI_TX_SECT_VC_SHIFT); 404 405 /* Data mode (bits [24:25]) */ 406 cfg |= ((ph_cfg->data_mode & MIPI_TX_SECT_DM_MASK) 407 << MIPI_TX_SECT_DM_SHIFT); 408 if (ph_cfg->dma_packed) 409 cfg |= MIPI_TX_SECT_DMA_PACKED; 410 411 dev_dbg(kmb_dsi->dev, 412 "ctrl=%d frame_id=%d section=%d cfg=%x packed=%d\n", 413 ctrl_no, frame_id, section, cfg, ph_cfg->dma_packed); 414 kmb_write_mipi(kmb_dsi, 415 (MIPI_TXm_HS_FGn_SECTo_PH(ctrl_no, frame_id, section)), 416 cfg); 417 418 /* Unpacked bytes */ 419 420 /* There are 4 frame generators and each fg has 4 sections 421 * There are 2 registers for unpacked bytes (# bytes each 422 * section occupies in memory) 423 * REG_UNPACKED_BYTES0: [15:0]-BYTES0, [31:16]-BYTES1 424 * REG_UNPACKED_BYTES1: [15:0]-BYTES2, [31:16]-BYTES3 425 */ 426 reg_adr = 427 MIPI_TXm_HS_FGn_SECT_UNPACKED_BYTES0(ctrl_no, 428 frame_id) + (section / 2) * 4; 429 kmb_write_bits_mipi(kmb_dsi, reg_adr, (section % 2) * 16, 16, 430 unpacked_bytes); 431 dev_dbg(kmb_dsi->dev, 432 "unpacked_bytes = %d, wordcount = %d\n", unpacked_bytes, 433 ph_cfg->wc); 434 435 /* Line config */ 436 reg_adr = MIPI_TXm_HS_FGn_SECTo_LINE_CFG(ctrl_no, frame_id, section); 437 kmb_write_mipi(kmb_dsi, reg_adr, height_lines); 438 return 0; 439 } 440 441 static u32 mipi_tx_fg_section_cfg(struct kmb_dsi *kmb_dsi, 442 u8 frame_id, u8 section, 443 struct mipi_tx_frame_section_cfg *frame_scfg, 444 u32 *bits_per_pclk, u32 *wc) 445 { 446 u32 ret = 0; 447 u32 unpacked_bytes; 448 struct mipi_data_type_params data_type_parameters; 449 struct mipi_tx_frame_sect_phcfg ph_cfg; 450 451 ret = mipi_get_datatype_params(frame_scfg->data_type, 452 frame_scfg->data_mode, 453 &data_type_parameters); 454 if (ret) 455 return ret; 456 457 /* Packet width has to be a multiple of the minimum packet width 458 * (in pixels) set for each data type 459 */ 460 if (frame_scfg->width_pixels % 461 data_type_parameters.size_constraint_pixels != 0) 462 return -EINVAL; 463 464 *wc = compute_wc(frame_scfg->width_pixels, 465 data_type_parameters.size_constraint_pixels, 466 data_type_parameters.size_constraint_bytes); 467 unpacked_bytes = compute_unpacked_bytes(*wc, 468 data_type_parameters.bits_per_pclk); 469 ph_cfg.wc = *wc; 470 ph_cfg.data_mode = frame_scfg->data_mode; 471 ph_cfg.data_type = frame_scfg->data_type; 472 ph_cfg.dma_packed = frame_scfg->dma_packed; 473 ph_cfg.vchannel = frame_id; 474 475 mipi_tx_fg_section_cfg_regs(kmb_dsi, frame_id, section, 476 frame_scfg->height_lines, 477 unpacked_bytes, &ph_cfg); 478 479 /* Caller needs bits_per_clk for additional caluclations */ 480 *bits_per_pclk = data_type_parameters.bits_per_pclk; 481 482 return 0; 483 } 484 485 static void mipi_tx_fg_cfg_regs(struct kmb_dsi *kmb_dsi, u8 frame_gen, 486 struct mipi_tx_frame_timing_cfg *fg_cfg) 487 { 488 u32 sysclk; 489 u32 ppl_llp_ratio; 490 u32 ctrl_no = MIPI_CTRL6, reg_adr, val, offset; 491 492 /* 500 Mhz system clock minus 50 to account for the difference in 493 * MIPI clock speed in RTL tests 494 */ 495 sysclk = kmb_dsi->sys_clk_mhz - 50; 496 497 /* PPL-Pixel Packing Layer, LLP-Low Level Protocol 498 * Frame genartor timing parameters are clocked on the system clock, 499 * whereas as the equivalent parameters in the LLP blocks are clocked 500 * on LLP Tx clock from the D-PHY - BYTE clock 501 */ 502 503 /* Multiply by 1000 to maintain precision */ 504 ppl_llp_ratio = ((fg_cfg->bpp / 8) * sysclk * 1000) / 505 ((fg_cfg->lane_rate_mbps / 8) * fg_cfg->active_lanes); 506 507 dev_dbg(kmb_dsi->dev, "ppl_llp_ratio=%d\n", ppl_llp_ratio); 508 dev_dbg(kmb_dsi->dev, "bpp=%d sysclk=%d lane-rate=%d active-lanes=%d\n", 509 fg_cfg->bpp, sysclk, fg_cfg->lane_rate_mbps, 510 fg_cfg->active_lanes); 511 512 /* Frame generator number of lines */ 513 reg_adr = MIPI_TXm_HS_FGn_NUM_LINES(ctrl_no, frame_gen); 514 kmb_write_mipi(kmb_dsi, reg_adr, fg_cfg->v_active); 515 516 /* vsync width 517 * There are 2 registers for vsync width (VSA in lines for 518 * channels 0-3) 519 * REG_VSYNC_WIDTH0: [15:0]-VSA for channel0, [31:16]-VSA for channel1 520 * REG_VSYNC_WIDTH1: [15:0]-VSA for channel2, [31:16]-VSA for channel3 521 */ 522 offset = (frame_gen % 2) * 16; 523 reg_adr = MIPI_TXm_HS_VSYNC_WIDTHn(ctrl_no, frame_gen / 2); 524 kmb_write_bits_mipi(kmb_dsi, reg_adr, offset, 16, fg_cfg->vsync_width); 525 526 /* vertical backporch (vbp) */ 527 reg_adr = MIPI_TXm_HS_V_BACKPORCHESn(ctrl_no, frame_gen / 2); 528 kmb_write_bits_mipi(kmb_dsi, reg_adr, offset, 16, fg_cfg->v_backporch); 529 530 /* vertical frontporch (vfp) */ 531 reg_adr = MIPI_TXm_HS_V_FRONTPORCHESn(ctrl_no, frame_gen / 2); 532 kmb_write_bits_mipi(kmb_dsi, reg_adr, offset, 16, fg_cfg->v_frontporch); 533 534 /* vertical active (vactive) */ 535 reg_adr = MIPI_TXm_HS_V_ACTIVEn(ctrl_no, frame_gen / 2); 536 kmb_write_bits_mipi(kmb_dsi, reg_adr, offset, 16, fg_cfg->v_active); 537 538 /* hsync width */ 539 reg_adr = MIPI_TXm_HS_HSYNC_WIDTHn(ctrl_no, frame_gen); 540 kmb_write_mipi(kmb_dsi, reg_adr, 541 (fg_cfg->hsync_width * ppl_llp_ratio) / 1000); 542 543 /* horizontal backporch (hbp) */ 544 reg_adr = MIPI_TXm_HS_H_BACKPORCHn(ctrl_no, frame_gen); 545 kmb_write_mipi(kmb_dsi, reg_adr, 546 (fg_cfg->h_backporch * ppl_llp_ratio) / 1000); 547 548 /* horizontal frontporch (hfp) */ 549 reg_adr = MIPI_TXm_HS_H_FRONTPORCHn(ctrl_no, frame_gen); 550 kmb_write_mipi(kmb_dsi, reg_adr, 551 (fg_cfg->h_frontporch * ppl_llp_ratio) / 1000); 552 553 /* horizontal active (ha) */ 554 reg_adr = MIPI_TXm_HS_H_ACTIVEn(ctrl_no, frame_gen); 555 556 /* convert h_active which is wc in bytes to cycles */ 557 val = (fg_cfg->h_active * sysclk * 1000) / 558 ((fg_cfg->lane_rate_mbps / 8) * fg_cfg->active_lanes); 559 val /= 1000; 560 kmb_write_mipi(kmb_dsi, reg_adr, val); 561 562 /* llp hsync width */ 563 reg_adr = MIPI_TXm_HS_LLP_HSYNC_WIDTHn(ctrl_no, frame_gen); 564 kmb_write_mipi(kmb_dsi, reg_adr, fg_cfg->hsync_width * (fg_cfg->bpp / 8)); 565 566 /* llp h backporch */ 567 reg_adr = MIPI_TXm_HS_LLP_H_BACKPORCHn(ctrl_no, frame_gen); 568 kmb_write_mipi(kmb_dsi, reg_adr, fg_cfg->h_backporch * (fg_cfg->bpp / 8)); 569 570 /* llp h frontporch */ 571 reg_adr = MIPI_TXm_HS_LLP_H_FRONTPORCHn(ctrl_no, frame_gen); 572 kmb_write_mipi(kmb_dsi, reg_adr, 573 fg_cfg->h_frontporch * (fg_cfg->bpp / 8)); 574 } 575 576 static void mipi_tx_fg_cfg(struct kmb_dsi *kmb_dsi, u8 frame_gen, 577 u8 active_lanes, u32 bpp, u32 wc, 578 u32 lane_rate_mbps, struct mipi_tx_frame_cfg *fg_cfg) 579 { 580 u32 i, fg_num_lines = 0; 581 struct mipi_tx_frame_timing_cfg fg_t_cfg; 582 583 /* Calculate the total frame generator number of 584 * lines based on it's active sections 585 */ 586 for (i = 0; i < MIPI_TX_FRAME_GEN_SECTIONS; i++) { 587 if (fg_cfg->sections[i]) 588 fg_num_lines += fg_cfg->sections[i]->height_lines; 589 } 590 591 fg_t_cfg.bpp = bpp; 592 fg_t_cfg.lane_rate_mbps = lane_rate_mbps; 593 fg_t_cfg.hsync_width = fg_cfg->hsync_width; 594 fg_t_cfg.h_backporch = fg_cfg->h_backporch; 595 fg_t_cfg.h_frontporch = fg_cfg->h_frontporch; 596 fg_t_cfg.h_active = wc; 597 fg_t_cfg.vsync_width = fg_cfg->vsync_width; 598 fg_t_cfg.v_backporch = fg_cfg->v_backporch; 599 fg_t_cfg.v_frontporch = fg_cfg->v_frontporch; 600 fg_t_cfg.v_active = fg_num_lines; 601 fg_t_cfg.active_lanes = active_lanes; 602 603 /* Apply frame generator timing setting */ 604 mipi_tx_fg_cfg_regs(kmb_dsi, frame_gen, &fg_t_cfg); 605 } 606 607 static void mipi_tx_multichannel_fifo_cfg(struct kmb_dsi *kmb_dsi, 608 u8 active_lanes, u8 vchannel_id) 609 { 610 u32 fifo_size, fifo_rthreshold; 611 u32 ctrl_no = MIPI_CTRL6; 612 613 /* Clear all mc fifo channel sizes and thresholds */ 614 kmb_write_mipi(kmb_dsi, MIPI_TX_HS_MC_FIFO_CTRL_EN, 0); 615 kmb_write_mipi(kmb_dsi, MIPI_TX_HS_MC_FIFO_CHAN_ALLOC0, 0); 616 kmb_write_mipi(kmb_dsi, MIPI_TX_HS_MC_FIFO_CHAN_ALLOC1, 0); 617 kmb_write_mipi(kmb_dsi, MIPI_TX_HS_MC_FIFO_RTHRESHOLD0, 0); 618 kmb_write_mipi(kmb_dsi, MIPI_TX_HS_MC_FIFO_RTHRESHOLD1, 0); 619 620 fifo_size = ((active_lanes > MIPI_D_LANES_PER_DPHY) ? 621 MIPI_CTRL_4LANE_MAX_MC_FIFO_LOC : 622 MIPI_CTRL_2LANE_MAX_MC_FIFO_LOC) - 1; 623 624 /* MC fifo size for virtual channels 0-3 625 * REG_MC_FIFO_CHAN_ALLOC0: [8:0]-channel0, [24:16]-channel1 626 * REG_MC_FIFO_CHAN_ALLOC1: [8:0]-2, [24:16]-channel3 627 */ 628 SET_MC_FIFO_CHAN_ALLOC(kmb_dsi, ctrl_no, vchannel_id, fifo_size); 629 630 /* Set threshold to half the fifo size, actual size=size*16 */ 631 fifo_rthreshold = ((fifo_size) * 8) & BIT_MASK_16; 632 SET_MC_FIFO_RTHRESHOLD(kmb_dsi, ctrl_no, vchannel_id, fifo_rthreshold); 633 634 /* Enable the MC FIFO channel corresponding to the Virtual Channel */ 635 kmb_set_bit_mipi(kmb_dsi, MIPI_TXm_HS_MC_FIFO_CTRL_EN(ctrl_no), 636 vchannel_id); 637 } 638 639 static void mipi_tx_ctrl_cfg(struct kmb_dsi *kmb_dsi, u8 fg_id, 640 struct mipi_ctrl_cfg *ctrl_cfg) 641 { 642 u32 sync_cfg = 0, ctrl = 0, fg_en; 643 u32 ctrl_no = MIPI_CTRL6; 644 645 /* MIPI_TX_HS_SYNC_CFG */ 646 if (ctrl_cfg->tx_ctrl_cfg.line_sync_pkt_en) 647 sync_cfg |= LINE_SYNC_PKT_ENABLE; 648 if (ctrl_cfg->tx_ctrl_cfg.frame_counter_active) 649 sync_cfg |= FRAME_COUNTER_ACTIVE; 650 if (ctrl_cfg->tx_ctrl_cfg.line_counter_active) 651 sync_cfg |= LINE_COUNTER_ACTIVE; 652 if (ctrl_cfg->tx_ctrl_cfg.tx_dsi_cfg->v_blanking) 653 sync_cfg |= DSI_V_BLANKING; 654 if (ctrl_cfg->tx_ctrl_cfg.tx_dsi_cfg->hsa_blanking) 655 sync_cfg |= DSI_HSA_BLANKING; 656 if (ctrl_cfg->tx_ctrl_cfg.tx_dsi_cfg->hbp_blanking) 657 sync_cfg |= DSI_HBP_BLANKING; 658 if (ctrl_cfg->tx_ctrl_cfg.tx_dsi_cfg->hfp_blanking) 659 sync_cfg |= DSI_HFP_BLANKING; 660 if (ctrl_cfg->tx_ctrl_cfg.tx_dsi_cfg->sync_pulse_eventn) 661 sync_cfg |= DSI_SYNC_PULSE_EVENTN; 662 if (ctrl_cfg->tx_ctrl_cfg.tx_dsi_cfg->lpm_first_vsa_line) 663 sync_cfg |= DSI_LPM_FIRST_VSA_LINE; 664 if (ctrl_cfg->tx_ctrl_cfg.tx_dsi_cfg->lpm_last_vfp_line) 665 sync_cfg |= DSI_LPM_LAST_VFP_LINE; 666 667 /* Enable frame generator */ 668 fg_en = 1 << fg_id; 669 sync_cfg |= FRAME_GEN_EN(fg_en); 670 671 if (ctrl_cfg->tx_ctrl_cfg.tx_always_use_hact) 672 sync_cfg |= ALWAYS_USE_HACT(fg_en); 673 if (ctrl_cfg->tx_ctrl_cfg.tx_hact_wait_stop) 674 sync_cfg |= HACT_WAIT_STOP(fg_en); 675 676 dev_dbg(kmb_dsi->dev, "sync_cfg=%d fg_en=%d\n", sync_cfg, fg_en); 677 678 /* MIPI_TX_HS_CTRL */ 679 680 /* type:DSI, source:LCD */ 681 ctrl = HS_CTRL_EN | TX_SOURCE; 682 ctrl |= LCD_VC(fg_id); 683 ctrl |= ACTIVE_LANES(ctrl_cfg->active_lanes - 1); 684 if (ctrl_cfg->tx_ctrl_cfg.tx_dsi_cfg->eotp_en) 685 ctrl |= DSI_EOTP_EN; 686 if (ctrl_cfg->tx_ctrl_cfg.tx_dsi_cfg->hfp_blank_en) 687 ctrl |= DSI_CMD_HFP_EN; 688 689 /*67 ns stop time */ 690 ctrl |= HSEXIT_CNT(0x43); 691 692 kmb_write_mipi(kmb_dsi, MIPI_TXm_HS_SYNC_CFG(ctrl_no), sync_cfg); 693 kmb_write_mipi(kmb_dsi, MIPI_TXm_HS_CTRL(ctrl_no), ctrl); 694 } 695 696 static u32 mipi_tx_init_cntrl(struct kmb_dsi *kmb_dsi, 697 struct mipi_ctrl_cfg *ctrl_cfg) 698 { 699 u32 ret = 0; 700 u8 active_vchannels = 0; 701 u8 frame_id, sect; 702 u32 bits_per_pclk = 0; 703 u32 word_count = 0; 704 struct mipi_tx_frame_cfg *frame; 705 706 /* This is the order to initialize MIPI TX: 707 * 1. set frame section parameters 708 * 2. set frame specific parameters 709 * 3. connect lcd to mipi 710 * 4. multi channel fifo cfg 711 * 5. set mipitxcctrlcfg 712 */ 713 714 for (frame_id = 0; frame_id < 4; frame_id++) { 715 frame = ctrl_cfg->tx_ctrl_cfg.frames[frame_id]; 716 717 /* Find valid frame, assume only one valid frame */ 718 if (!frame) 719 continue; 720 721 /* Frame Section configuration */ 722 /* TODO - assume there is only one valid section in a frame, 723 * so bits_per_pclk and word_count are only set once 724 */ 725 for (sect = 0; sect < MIPI_CTRL_VIRTUAL_CHANNELS; sect++) { 726 if (!frame->sections[sect]) 727 continue; 728 729 ret = mipi_tx_fg_section_cfg(kmb_dsi, frame_id, sect, 730 frame->sections[sect], 731 &bits_per_pclk, 732 &word_count); 733 if (ret) 734 return ret; 735 } 736 737 /* Set frame specific parameters */ 738 mipi_tx_fg_cfg(kmb_dsi, frame_id, ctrl_cfg->active_lanes, 739 bits_per_pclk, word_count, 740 ctrl_cfg->lane_rate_mbps, frame); 741 742 active_vchannels++; 743 744 /* Stop iterating as only one virtual channel 745 * shall be used for LCD connection 746 */ 747 break; 748 } 749 750 if (active_vchannels == 0) 751 return -EINVAL; 752 /* Multi-Channel FIFO Configuration */ 753 mipi_tx_multichannel_fifo_cfg(kmb_dsi, ctrl_cfg->active_lanes, frame_id); 754 755 /* Frame Generator Enable */ 756 mipi_tx_ctrl_cfg(kmb_dsi, frame_id, ctrl_cfg); 757 758 return ret; 759 } 760 761 static void test_mode_send(struct kmb_dsi *kmb_dsi, u32 dphy_no, 762 u32 test_code, u32 test_data) 763 { 764 /* Steps to send test code: 765 * - set testclk HIGH 766 * - set testdin with test code 767 * - set testen HIGH 768 * - set testclk LOW 769 * - set testen LOW 770 */ 771 772 /* Set testclk high */ 773 SET_DPHY_TEST_CTRL1_CLK(kmb_dsi, dphy_no); 774 775 /* Set testdin */ 776 SET_TEST_DIN0_3(kmb_dsi, dphy_no, test_code); 777 778 /* Set testen high */ 779 SET_DPHY_TEST_CTRL1_EN(kmb_dsi, dphy_no); 780 781 /* Set testclk low */ 782 CLR_DPHY_TEST_CTRL1_CLK(kmb_dsi, dphy_no); 783 784 /* Set testen low */ 785 CLR_DPHY_TEST_CTRL1_EN(kmb_dsi, dphy_no); 786 787 if (test_code) { 788 /* Steps to send test data: 789 * - set testen LOW 790 * - set testclk LOW 791 * - set testdin with data 792 * - set testclk HIGH 793 */ 794 795 /* Set testen low */ 796 CLR_DPHY_TEST_CTRL1_EN(kmb_dsi, dphy_no); 797 798 /* Set testclk low */ 799 CLR_DPHY_TEST_CTRL1_CLK(kmb_dsi, dphy_no); 800 801 /* Set data in testdin */ 802 kmb_write_mipi(kmb_dsi, 803 DPHY_TEST_DIN0_3 + ((dphy_no / 0x4) * 0x4), 804 test_data << ((dphy_no % 4) * 8)); 805 806 /* Set testclk high */ 807 SET_DPHY_TEST_CTRL1_CLK(kmb_dsi, dphy_no); 808 } 809 } 810 811 static inline void 812 set_test_mode_src_osc_freq_target_low_bits(struct kmb_dsi *kmb_dsi, 813 u32 dphy_no, 814 u32 freq) 815 { 816 /* Typical rise/fall time=166, refer Table 1207 databook, 817 * sr_osc_freq_target[7:0] 818 */ 819 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_SLEW_RATE_DDL_CYCLES, 820 (freq & 0x7f)); 821 } 822 823 static inline void 824 set_test_mode_src_osc_freq_target_hi_bits(struct kmb_dsi *kmb_dsi, 825 u32 dphy_no, 826 u32 freq) 827 { 828 u32 data; 829 830 /* Flag this as high nibble */ 831 data = ((freq >> 6) & 0x1f) | (1 << 7); 832 833 /* Typical rise/fall time=166, refer Table 1207 databook, 834 * sr_osc_freq_target[11:7] 835 */ 836 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_SLEW_RATE_DDL_CYCLES, data); 837 } 838 839 static void mipi_tx_get_vco_params(struct vco_params *vco) 840 { 841 int i; 842 843 for (i = 0; i < ARRAY_SIZE(vco_table); i++) { 844 if (vco->freq < vco_table[i].freq) { 845 *vco = vco_table[i]; 846 return; 847 } 848 } 849 850 WARN_ONCE(1, "Invalid vco freq = %u for PLL setup\n", vco->freq); 851 } 852 853 static void mipi_tx_pll_setup(struct kmb_dsi *kmb_dsi, u32 dphy_no, 854 u32 ref_clk_mhz, u32 target_freq_mhz) 855 { 856 u32 best_n = 0, best_m = 0; 857 u32 n = 0, m = 0, div = 0, delta, freq = 0, t_freq; 858 u32 best_freq_delta = 3000; 859 860 /* pll_ref_clk: - valid range: 2~64 MHz; Typically 24 MHz 861 * Fvco: - valid range: 320~1250 MHz (Gen3 D-PHY) 862 * Fout: - valid range: 40~1250 MHz (Gen3 D-PHY) 863 * n: - valid range [0 15] 864 * N: - N = n + 1 865 * -valid range: [1 16] 866 * -conditions: - (pll_ref_clk / N) >= 2 MHz 867 * -(pll_ref_clk / N) <= 8 MHz 868 * m: valid range [62 623] 869 * M: - M = m + 2 870 * -valid range [64 625] 871 * -Fvco = (M/N) * pll_ref_clk 872 */ 873 struct vco_params vco_p = { 874 .range = 0, 875 .divider = 1, 876 }; 877 878 vco_p.freq = target_freq_mhz; 879 mipi_tx_get_vco_params(&vco_p); 880 881 /* Search pll n parameter */ 882 for (n = PLL_N_MIN; n <= PLL_N_MAX; n++) { 883 /* Calculate the pll input frequency division ratio 884 * multiply by 1000 for precision - 885 * no floating point, add n for rounding 886 */ 887 div = ((ref_clk_mhz * 1000) + n) / (n + 1); 888 889 /* Found a valid n parameter */ 890 if ((div < 2000 || div > 8000)) 891 continue; 892 893 /* Search pll m parameter */ 894 for (m = PLL_M_MIN; m <= PLL_M_MAX; m++) { 895 /* Calculate the Fvco(DPHY PLL output frequency) 896 * using the current n,m params 897 */ 898 freq = div * (m + 2); 899 freq /= 1000; 900 901 /* Trim the potential pll freq to max supported */ 902 if (freq > PLL_FVCO_MAX) 903 continue; 904 905 delta = abs(freq - target_freq_mhz); 906 907 /* Select the best (closest to target pll freq) 908 * n,m parameters so far 909 */ 910 if (delta < best_freq_delta) { 911 best_n = n; 912 best_m = m; 913 best_freq_delta = delta; 914 } 915 } 916 } 917 918 /* Program vco_cntrl parameter 919 * PLL_VCO_Control[5:0] = pll_vco_cntrl_ovr, 920 * PLL_VCO_Control[6] = pll_vco_cntrl_ovr_en 921 */ 922 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_PLL_VCO_CTRL, (vco_p.range 923 | (1 << 6))); 924 925 /* Program m, n pll parameters */ 926 dev_dbg(kmb_dsi->dev, "m = %d n = %d\n", best_m, best_n); 927 928 /* PLL_Input_Divider_Ratio[3:0] = pll_n_ovr */ 929 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_PLL_INPUT_DIVIDER, 930 (best_n & 0x0f)); 931 932 /* m - low nibble PLL_Loop_Divider_Ratio[4:0] 933 * pll_m_ovr[4:0] 934 */ 935 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_PLL_FEEDBACK_DIVIDER, 936 (best_m & 0x1f)); 937 938 /* m - high nibble PLL_Loop_Divider_Ratio[4:0] 939 * pll_m_ovr[9:5] 940 */ 941 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_PLL_FEEDBACK_DIVIDER, 942 ((best_m >> 5) & 0x1f) | PLL_FEEDBACK_DIVIDER_HIGH); 943 944 /* Enable overwrite of n,m parameters :pll_n_ovr_en, pll_m_ovr_en */ 945 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_PLL_OUTPUT_CLK_SEL, 946 (PLL_N_OVR_EN | PLL_M_OVR_EN)); 947 948 /* Program Charge-Pump parameters */ 949 950 /* pll_prop_cntrl-fixed values for prop_cntrl from DPHY doc */ 951 t_freq = target_freq_mhz * vco_p.divider; 952 test_mode_send(kmb_dsi, dphy_no, 953 TEST_CODE_PLL_PROPORTIONAL_CHARGE_PUMP_CTRL, 954 ((t_freq > 1150) ? 0x0C : 0x0B)); 955 956 /* pll_int_cntrl-fixed value for int_cntrl from DPHY doc */ 957 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_PLL_INTEGRAL_CHARGE_PUMP_CTRL, 958 0x00); 959 960 /* pll_gmp_cntrl-fixed value for gmp_cntrl from DPHY doci */ 961 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_PLL_GMP_CTRL, 0x10); 962 963 /* pll_cpbias_cntrl-fixed value for cpbias_cntrl from DPHY doc */ 964 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_PLL_CHARGE_PUMP_BIAS, 0x10); 965 966 /* pll_th1 -Lock Detector Phase error threshold, 967 * document gives fixed value 968 */ 969 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_PLL_PHASE_ERR_CTRL, 0x02); 970 971 /* PLL Lock Configuration */ 972 973 /* pll_th2 - Lock Filter length, document gives fixed value */ 974 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_PLL_LOCK_FILTER, 0x60); 975 976 /* pll_th3- PLL Unlocking filter, document gives fixed value */ 977 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_PLL_UNLOCK_FILTER, 0x03); 978 979 /* pll_lock_sel-PLL Lock Detector Selection, 980 * document gives fixed value 981 */ 982 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_PLL_LOCK_DETECTOR, 0x02); 983 } 984 985 static void set_slewrate_gt_1500(struct kmb_dsi *kmb_dsi, u32 dphy_no) 986 { 987 u32 test_code = 0, test_data = 0; 988 /* Bypass slew rate calibration algorithm 989 * bits[1:0} srcal_en_ovr_en, srcal_en_ovr 990 */ 991 test_code = TEST_CODE_SLEW_RATE_OVERRIDE_CTRL; 992 test_data = 0x02; 993 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 994 995 /* Disable slew rate calibration */ 996 test_code = TEST_CODE_SLEW_RATE_DDL_LOOP_CTRL; 997 test_data = 0x00; 998 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 999 } 1000 1001 static void set_slewrate_gt_1000(struct kmb_dsi *kmb_dsi, u32 dphy_no) 1002 { 1003 u32 test_code = 0, test_data = 0; 1004 1005 /* BitRate: > 1 Gbps && <= 1.5 Gbps: - slew rate control ON 1006 * typical rise/fall times: 166 ps 1007 */ 1008 1009 /* Do not bypass slew rate calibration algorithm 1010 * bits[1:0}=srcal_en_ovr_en, srcal_en_ovr, bit[6]=sr_range 1011 */ 1012 test_code = TEST_CODE_SLEW_RATE_OVERRIDE_CTRL; 1013 test_data = (0x03 | (1 << 6)); 1014 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1015 1016 /* Enable slew rate calibration */ 1017 test_code = TEST_CODE_SLEW_RATE_DDL_LOOP_CTRL; 1018 test_data = 0x01; 1019 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1020 1021 /* Set sr_osc_freq_target[6:0] low nibble 1022 * typical rise/fall time=166, refer Table 1207 databook 1023 */ 1024 test_code = TEST_CODE_SLEW_RATE_DDL_CYCLES; 1025 test_data = (0x72f & 0x7f); 1026 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1027 1028 /* Set sr_osc_freq_target[11:7] high nibble 1029 * Typical rise/fall time=166, refer Table 1207 databook 1030 */ 1031 test_code = TEST_CODE_SLEW_RATE_DDL_CYCLES; 1032 test_data = ((0x72f >> 6) & 0x1f) | (1 << 7); 1033 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1034 } 1035 1036 static void set_slewrate_lt_1000(struct kmb_dsi *kmb_dsi, u32 dphy_no) 1037 { 1038 u32 test_code = 0, test_data = 0; 1039 1040 /* lane_rate_mbps <= 1000 Mbps 1041 * BitRate: <= 1 Gbps: 1042 * - slew rate control ON 1043 * - typical rise/fall times: 225 ps 1044 */ 1045 1046 /* Do not bypass slew rate calibration algorithm */ 1047 test_code = TEST_CODE_SLEW_RATE_OVERRIDE_CTRL; 1048 test_data = (0x03 | (1 << 6)); 1049 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1050 1051 /* Enable slew rate calibration */ 1052 test_code = TEST_CODE_SLEW_RATE_DDL_LOOP_CTRL; 1053 test_data = 0x01; 1054 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1055 1056 /* Typical rise/fall time=255, refer Table 1207 databook */ 1057 test_code = TEST_CODE_SLEW_RATE_DDL_CYCLES; 1058 test_data = (0x523 & 0x7f); 1059 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1060 1061 /* Set sr_osc_freq_target[11:7] high nibble */ 1062 test_code = TEST_CODE_SLEW_RATE_DDL_CYCLES; 1063 test_data = ((0x523 >> 6) & 0x1f) | (1 << 7); 1064 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1065 } 1066 1067 static void setup_pll(struct kmb_dsi *kmb_dsi, u32 dphy_no, 1068 struct mipi_ctrl_cfg *cfg) 1069 { 1070 u32 test_code = 0, test_data = 0; 1071 1072 /* Set PLL regulator in bypass */ 1073 test_code = TEST_CODE_PLL_ANALOG_PROG; 1074 test_data = 0x01; 1075 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1076 1077 /* PLL Parameters Setup */ 1078 mipi_tx_pll_setup(kmb_dsi, dphy_no, cfg->ref_clk_khz / 1000, 1079 cfg->lane_rate_mbps / 2); 1080 1081 /* Set clksel */ 1082 kmb_write_bits_mipi(kmb_dsi, DPHY_INIT_CTRL1, PLL_CLKSEL_0, 2, 0x01); 1083 1084 /* Set pll_shadow_control */ 1085 kmb_set_bit_mipi(kmb_dsi, DPHY_INIT_CTRL1, PLL_SHADOW_CTRL); 1086 } 1087 1088 static void set_lane_data_rate(struct kmb_dsi *kmb_dsi, u32 dphy_no, 1089 struct mipi_ctrl_cfg *cfg) 1090 { 1091 u32 i, test_code = 0, test_data = 0; 1092 1093 for (i = 0; i < MIPI_DPHY_DEFAULT_BIT_RATES; i++) { 1094 if (mipi_hs_freq_range[i].default_bit_rate_mbps < 1095 cfg->lane_rate_mbps) 1096 continue; 1097 1098 /* Send the test code and data */ 1099 /* bit[6:0] = hsfreqrange_ovr bit[7] = hsfreqrange_ovr_en */ 1100 test_code = TEST_CODE_HS_FREQ_RANGE_CFG; 1101 test_data = (mipi_hs_freq_range[i].hsfreqrange_code & 0x7f) | 1102 (1 << 7); 1103 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1104 break; 1105 } 1106 } 1107 1108 static void dphy_init_sequence(struct kmb_dsi *kmb_dsi, 1109 struct mipi_ctrl_cfg *cfg, u32 dphy_no, 1110 int active_lanes, enum dphy_mode mode) 1111 { 1112 u32 test_code = 0, test_data = 0, val; 1113 1114 /* Set D-PHY in shutdown mode */ 1115 /* Assert RSTZ signal */ 1116 CLR_DPHY_INIT_CTRL0(kmb_dsi, dphy_no, RESETZ); 1117 1118 /* Assert SHUTDOWNZ signal */ 1119 CLR_DPHY_INIT_CTRL0(kmb_dsi, dphy_no, SHUTDOWNZ); 1120 val = kmb_read_mipi(kmb_dsi, DPHY_INIT_CTRL0); 1121 1122 /* Init D-PHY_n 1123 * Pulse testclear signal to make sure the d-phy configuration 1124 * starts from a clean base 1125 */ 1126 CLR_DPHY_TEST_CTRL0(kmb_dsi, dphy_no); 1127 ndelay(15); 1128 SET_DPHY_TEST_CTRL0(kmb_dsi, dphy_no); 1129 ndelay(15); 1130 CLR_DPHY_TEST_CTRL0(kmb_dsi, dphy_no); 1131 ndelay(15); 1132 1133 /* Set mastermacro bit - Master or slave mode */ 1134 test_code = TEST_CODE_MULTIPLE_PHY_CTRL; 1135 1136 /* DPHY has its own clock lane enabled (master) */ 1137 if (mode == MIPI_DPHY_MASTER) 1138 test_data = 0x01; 1139 else 1140 test_data = 0x00; 1141 1142 /* Send the test code and data */ 1143 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1144 1145 /* Set the lane data rate */ 1146 set_lane_data_rate(kmb_dsi, dphy_no, cfg); 1147 1148 /* High-Speed Tx Slew Rate Calibration 1149 * BitRate: > 1.5 Gbps && <= 2.5 Gbps: slew rate control OFF 1150 */ 1151 if (cfg->lane_rate_mbps > 1500) 1152 set_slewrate_gt_1500(kmb_dsi, dphy_no); 1153 else if (cfg->lane_rate_mbps > 1000) 1154 set_slewrate_gt_1000(kmb_dsi, dphy_no); 1155 else 1156 set_slewrate_lt_1000(kmb_dsi, dphy_no); 1157 1158 /* Set cfgclkfreqrange */ 1159 val = (((cfg->cfg_clk_khz / 1000) - 17) * 4) & 0x3f; 1160 SET_DPHY_FREQ_CTRL0_3(kmb_dsi, dphy_no, val); 1161 1162 /* Enable config clk for the corresponding d-phy */ 1163 kmb_set_bit_mipi(kmb_dsi, DPHY_CFG_CLK_EN, dphy_no); 1164 1165 /* PLL setup */ 1166 if (mode == MIPI_DPHY_MASTER) 1167 setup_pll(kmb_dsi, dphy_no, cfg); 1168 1169 /* Send NORMAL OPERATION test code */ 1170 test_code = 0x0; 1171 test_data = 0x0; 1172 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1173 1174 /* Configure BASEDIR for data lanes 1175 * NOTE: basedir only applies to LANE_0 of each D-PHY. 1176 * The other lanes keep their direction based on the D-PHY type, 1177 * either Rx or Tx. 1178 * bits[5:0] - BaseDir: 1 = Rx 1179 * bits[9:6] - BaseDir: 0 = Tx 1180 */ 1181 kmb_write_bits_mipi(kmb_dsi, DPHY_INIT_CTRL2, 0, 9, 0x03f); 1182 ndelay(15); 1183 1184 /* Enable CLOCK LANE 1185 * Clock lane should be enabled regardless of the direction 1186 * set for the D-PHY (Rx/Tx) 1187 */ 1188 kmb_set_bit_mipi(kmb_dsi, DPHY_INIT_CTRL2, 12 + dphy_no); 1189 1190 /* Enable DATA LANES */ 1191 kmb_write_bits_mipi(kmb_dsi, DPHY_ENABLE, dphy_no * 2, 2, 1192 ((1 << active_lanes) - 1)); 1193 1194 ndelay(15); 1195 1196 /* Take D-PHY out of shutdown mode */ 1197 /* Deassert SHUTDOWNZ signal */ 1198 SET_DPHY_INIT_CTRL0(kmb_dsi, dphy_no, SHUTDOWNZ); 1199 ndelay(15); 1200 1201 /* Deassert RSTZ signal */ 1202 SET_DPHY_INIT_CTRL0(kmb_dsi, dphy_no, RESETZ); 1203 } 1204 1205 static void dphy_wait_fsm(struct kmb_dsi *kmb_dsi, u32 dphy_no, 1206 enum dphy_tx_fsm fsm_state) 1207 { 1208 enum dphy_tx_fsm val = DPHY_TX_POWERDWN; 1209 int i = 0; 1210 int status = 1; 1211 1212 do { 1213 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_FSM_CONTROL, 0x80); 1214 1215 val = GET_TEST_DOUT4_7(kmb_dsi, dphy_no); 1216 i++; 1217 if (i > TIMEOUT) { 1218 status = 0; 1219 break; 1220 } 1221 } while (val != fsm_state); 1222 1223 dev_dbg(kmb_dsi->dev, "%s: dphy %d val = %x", __func__, dphy_no, val); 1224 dev_dbg(kmb_dsi->dev, "* DPHY %d WAIT_FSM %s *", 1225 dphy_no, status ? "SUCCESS" : "FAILED"); 1226 } 1227 1228 static void wait_init_done(struct kmb_dsi *kmb_dsi, u32 dphy_no, 1229 u32 active_lanes) 1230 { 1231 u32 stopstatedata = 0; 1232 u32 data_lanes = (1 << active_lanes) - 1; 1233 int i = 0; 1234 int status = 1; 1235 1236 do { 1237 stopstatedata = GET_STOPSTATE_DATA(kmb_dsi, dphy_no) 1238 & data_lanes; 1239 1240 /* TODO-need to add a time out and return failure */ 1241 i++; 1242 1243 if (i > TIMEOUT) { 1244 status = 0; 1245 dev_dbg(kmb_dsi->dev, 1246 "! WAIT_INIT_DONE: TIMING OUT!(err_stat=%d)", 1247 kmb_read_mipi(kmb_dsi, MIPI_DPHY_ERR_STAT6_7)); 1248 break; 1249 } 1250 } while (stopstatedata != data_lanes); 1251 1252 dev_dbg(kmb_dsi->dev, "* DPHY %d INIT - %s *", 1253 dphy_no, status ? "SUCCESS" : "FAILED"); 1254 } 1255 1256 static void wait_pll_lock(struct kmb_dsi *kmb_dsi, u32 dphy_no) 1257 { 1258 int i = 0; 1259 int status = 1; 1260 1261 do { 1262 /* TODO-need to add a time out and return failure */ 1263 i++; 1264 if (i > TIMEOUT) { 1265 status = 0; 1266 dev_dbg(kmb_dsi->dev, "%s: timing out", __func__); 1267 break; 1268 } 1269 } while (!GET_PLL_LOCK(kmb_dsi, dphy_no)); 1270 1271 dev_dbg(kmb_dsi->dev, "* PLL Locked for DPHY %d - %s *", 1272 dphy_no, status ? "SUCCESS" : "FAILED"); 1273 } 1274 1275 static u32 mipi_tx_init_dphy(struct kmb_dsi *kmb_dsi, 1276 struct mipi_ctrl_cfg *cfg) 1277 { 1278 u32 dphy_no = MIPI_DPHY6; 1279 1280 /* Multiple D-PHYs needed */ 1281 if (cfg->active_lanes > MIPI_DPHY_D_LANES) { 1282 /* 1283 *Initialization for Tx aggregation mode is done according to 1284 *a. start init PHY1 1285 *b. poll for PHY1 FSM state LOCK 1286 * b1. reg addr 0x03[3:0] - state_main[3:0] == 5 (LOCK) 1287 *c. poll for PHY1 calibrations done : 1288 * c1. termination calibration lower section: addr 0x22[5] 1289 * - rescal_done 1290 * c2. slewrate calibration (if data rate < = 1500 Mbps): 1291 * addr 0xA7[3:2] - srcal_done, sr_finished 1292 *d. start init PHY0 1293 *e. poll for PHY0 stopstate 1294 *f. poll for PHY1 stopstate 1295 */ 1296 /* PHY #N+1 ('slave') */ 1297 1298 dphy_init_sequence(kmb_dsi, cfg, dphy_no + 1, 1299 (cfg->active_lanes - MIPI_DPHY_D_LANES), 1300 MIPI_DPHY_SLAVE); 1301 dphy_wait_fsm(kmb_dsi, dphy_no + 1, DPHY_TX_LOCK); 1302 1303 /* PHY #N master */ 1304 dphy_init_sequence(kmb_dsi, cfg, dphy_no, MIPI_DPHY_D_LANES, 1305 MIPI_DPHY_MASTER); 1306 1307 /* Wait for DPHY init to complete */ 1308 wait_init_done(kmb_dsi, dphy_no, MIPI_DPHY_D_LANES); 1309 wait_init_done(kmb_dsi, dphy_no + 1, 1310 cfg->active_lanes - MIPI_DPHY_D_LANES); 1311 wait_pll_lock(kmb_dsi, dphy_no); 1312 wait_pll_lock(kmb_dsi, dphy_no + 1); 1313 dphy_wait_fsm(kmb_dsi, dphy_no, DPHY_TX_IDLE); 1314 } else { /* Single DPHY */ 1315 dphy_init_sequence(kmb_dsi, cfg, dphy_no, cfg->active_lanes, 1316 MIPI_DPHY_MASTER); 1317 dphy_wait_fsm(kmb_dsi, dphy_no, DPHY_TX_IDLE); 1318 wait_init_done(kmb_dsi, dphy_no, cfg->active_lanes); 1319 wait_pll_lock(kmb_dsi, dphy_no); 1320 } 1321 1322 return 0; 1323 } 1324 1325 static void connect_lcd_to_mipi(struct kmb_dsi *kmb_dsi) 1326 { 1327 struct regmap *msscam; 1328 1329 msscam = syscon_regmap_lookup_by_compatible("intel,keembay-msscam"); 1330 if (IS_ERR(msscam)) { 1331 dev_dbg(kmb_dsi->dev, "failed to get msscam syscon"); 1332 return; 1333 } 1334 1335 /* DISABLE MIPI->CIF CONNECTION */ 1336 regmap_write(msscam, MSS_MIPI_CIF_CFG, 0); 1337 1338 /* ENABLE LCD->MIPI CONNECTION */ 1339 regmap_write(msscam, MSS_LCD_MIPI_CFG, 1); 1340 /* DISABLE LCD->CIF LOOPBACK */ 1341 regmap_write(msscam, MSS_LOOPBACK_CFG, 1); 1342 } 1343 1344 int kmb_dsi_mode_set(struct kmb_dsi *kmb_dsi, struct drm_display_mode *mode, 1345 int sys_clk_mhz) 1346 { 1347 u64 data_rate; 1348 1349 kmb_dsi->sys_clk_mhz = sys_clk_mhz; 1350 mipi_tx_init_cfg.active_lanes = MIPI_TX_ACTIVE_LANES; 1351 1352 mipi_tx_frame0_sect_cfg.width_pixels = mode->crtc_hdisplay; 1353 mipi_tx_frame0_sect_cfg.height_lines = mode->crtc_vdisplay; 1354 mipitx_frame0_cfg.vsync_width = 1355 mode->crtc_vsync_end - mode->crtc_vsync_start; 1356 mipitx_frame0_cfg.v_backporch = 1357 mode->crtc_vtotal - mode->crtc_vsync_end; 1358 mipitx_frame0_cfg.v_frontporch = 1359 mode->crtc_vsync_start - mode->crtc_vdisplay; 1360 mipitx_frame0_cfg.hsync_width = 1361 mode->crtc_hsync_end - mode->crtc_hsync_start; 1362 mipitx_frame0_cfg.h_backporch = 1363 mode->crtc_htotal - mode->crtc_hsync_end; 1364 mipitx_frame0_cfg.h_frontporch = 1365 mode->crtc_hsync_start - mode->crtc_hdisplay; 1366 1367 /* Lane rate = (vtotal*htotal*fps*bpp)/4 / 1000000 1368 * to convert to Mbps 1369 */ 1370 data_rate = ((((u32)mode->crtc_vtotal * (u32)mode->crtc_htotal) * 1371 (u32)(drm_mode_vrefresh(mode)) * 1372 MIPI_TX_BPP) / mipi_tx_init_cfg.active_lanes) / 1000000; 1373 1374 dev_dbg(kmb_dsi->dev, "data_rate=%u active_lanes=%d\n", 1375 (u32)data_rate, mipi_tx_init_cfg.active_lanes); 1376 1377 /* When late rate < 800, modeset fails with 4 lanes, 1378 * so switch to 2 lanes 1379 */ 1380 if (data_rate < 800) { 1381 mipi_tx_init_cfg.active_lanes = 2; 1382 mipi_tx_init_cfg.lane_rate_mbps = data_rate * 2; 1383 } else { 1384 mipi_tx_init_cfg.lane_rate_mbps = data_rate; 1385 } 1386 1387 kmb_write_mipi(kmb_dsi, DPHY_ENABLE, 0); 1388 kmb_write_mipi(kmb_dsi, DPHY_INIT_CTRL0, 0); 1389 kmb_write_mipi(kmb_dsi, DPHY_INIT_CTRL1, 0); 1390 kmb_write_mipi(kmb_dsi, DPHY_INIT_CTRL2, 0); 1391 1392 /* Initialize mipi controller */ 1393 mipi_tx_init_cntrl(kmb_dsi, &mipi_tx_init_cfg); 1394 1395 /* Dphy initialization */ 1396 mipi_tx_init_dphy(kmb_dsi, &mipi_tx_init_cfg); 1397 1398 connect_lcd_to_mipi(kmb_dsi); 1399 dev_info(kmb_dsi->dev, "mipi hw initialized"); 1400 1401 return 0; 1402 } 1403 1404 struct kmb_dsi *kmb_dsi_init(struct platform_device *pdev) 1405 { 1406 struct kmb_dsi *kmb_dsi; 1407 struct device *dev = get_device(&pdev->dev); 1408 1409 kmb_dsi = devm_kzalloc(dev, sizeof(*kmb_dsi), GFP_KERNEL); 1410 if (!kmb_dsi) { 1411 dev_err(dev, "failed to allocate kmb_dsi\n"); 1412 return ERR_PTR(-ENOMEM); 1413 } 1414 1415 kmb_dsi->host = dsi_host; 1416 kmb_dsi->host->ops = &kmb_dsi_host_ops; 1417 1418 dsi_device->host = kmb_dsi->host; 1419 kmb_dsi->device = dsi_device; 1420 1421 return kmb_dsi; 1422 } 1423 1424 int kmb_dsi_encoder_init(struct drm_device *dev, struct kmb_dsi *kmb_dsi) 1425 { 1426 struct drm_encoder *encoder; 1427 struct drm_connector *connector; 1428 int ret = 0; 1429 1430 encoder = &kmb_dsi->base; 1431 encoder->possible_crtcs = 1; 1432 encoder->possible_clones = 0; 1433 1434 ret = drm_simple_encoder_init(dev, encoder, DRM_MODE_ENCODER_DSI); 1435 if (ret) { 1436 dev_err(kmb_dsi->dev, "Failed to init encoder %d\n", ret); 1437 return ret; 1438 } 1439 1440 /* Link drm_bridge to encoder */ 1441 ret = drm_bridge_attach(encoder, adv_bridge, NULL, 1442 DRM_BRIDGE_ATTACH_NO_CONNECTOR); 1443 if (ret) { 1444 DRM_ERROR("failed to attach bridge to MIPI\n"); 1445 drm_encoder_cleanup(encoder); 1446 return ret; 1447 } 1448 drm_info(dev, "Bridge attached : SUCCESS"); 1449 connector = drm_bridge_connector_init(dev, encoder); 1450 if (IS_ERR(connector)) { 1451 DRM_ERROR("Unable to create bridge connector"); 1452 drm_encoder_cleanup(encoder); 1453 return PTR_ERR(connector); 1454 } 1455 drm_connector_attach_encoder(connector, encoder); 1456 return 0; 1457 } 1458 1459 int kmb_dsi_map_mmio(struct kmb_dsi *kmb_dsi) 1460 { 1461 struct resource *res; 1462 struct device *dev = kmb_dsi->dev; 1463 1464 res = platform_get_resource_byname(kmb_dsi->pdev, IORESOURCE_MEM, 1465 "mipi"); 1466 if (!res) { 1467 dev_err(dev, "failed to get resource for mipi"); 1468 return -ENOMEM; 1469 } 1470 kmb_dsi->mipi_mmio = devm_ioremap_resource(dev, res); 1471 if (IS_ERR(kmb_dsi->mipi_mmio)) { 1472 dev_err(dev, "failed to ioremap mipi registers"); 1473 return PTR_ERR(kmb_dsi->mipi_mmio); 1474 } 1475 return 0; 1476 } 1477 1478 static int kmb_dsi_clk_enable(struct kmb_dsi *kmb_dsi) 1479 { 1480 int ret; 1481 struct device *dev = kmb_dsi->dev; 1482 1483 ret = clk_prepare_enable(kmb_dsi->clk_mipi); 1484 if (ret) { 1485 dev_err(dev, "Failed to enable MIPI clock: %d\n", ret); 1486 return ret; 1487 } 1488 1489 ret = clk_prepare_enable(kmb_dsi->clk_mipi_ecfg); 1490 if (ret) { 1491 dev_err(dev, "Failed to enable MIPI_ECFG clock: %d\n", ret); 1492 return ret; 1493 } 1494 1495 ret = clk_prepare_enable(kmb_dsi->clk_mipi_cfg); 1496 if (ret) { 1497 dev_err(dev, "Failed to enable MIPI_CFG clock: %d\n", ret); 1498 return ret; 1499 } 1500 1501 dev_info(dev, "SUCCESS : enabled MIPI clocks\n"); 1502 return 0; 1503 } 1504 1505 int kmb_dsi_clk_init(struct kmb_dsi *kmb_dsi) 1506 { 1507 struct device *dev = kmb_dsi->dev; 1508 unsigned long clk; 1509 1510 kmb_dsi->clk_mipi = devm_clk_get(dev, "clk_mipi"); 1511 if (IS_ERR(kmb_dsi->clk_mipi)) { 1512 dev_err(dev, "devm_clk_get() failed clk_mipi\n"); 1513 return PTR_ERR(kmb_dsi->clk_mipi); 1514 } 1515 1516 kmb_dsi->clk_mipi_ecfg = devm_clk_get(dev, "clk_mipi_ecfg"); 1517 if (IS_ERR(kmb_dsi->clk_mipi_ecfg)) { 1518 dev_err(dev, "devm_clk_get() failed clk_mipi_ecfg\n"); 1519 return PTR_ERR(kmb_dsi->clk_mipi_ecfg); 1520 } 1521 1522 kmb_dsi->clk_mipi_cfg = devm_clk_get(dev, "clk_mipi_cfg"); 1523 if (IS_ERR(kmb_dsi->clk_mipi_cfg)) { 1524 dev_err(dev, "devm_clk_get() failed clk_mipi_cfg\n"); 1525 return PTR_ERR(kmb_dsi->clk_mipi_cfg); 1526 } 1527 /* Set MIPI clock to 24 Mhz */ 1528 clk_set_rate(kmb_dsi->clk_mipi, KMB_MIPI_DEFAULT_CLK); 1529 if (clk_get_rate(kmb_dsi->clk_mipi) != KMB_MIPI_DEFAULT_CLK) { 1530 dev_err(dev, "failed to set to clk_mipi to %d\n", 1531 KMB_MIPI_DEFAULT_CLK); 1532 return -1; 1533 } 1534 dev_dbg(dev, "clk_mipi = %ld\n", clk_get_rate(kmb_dsi->clk_mipi)); 1535 1536 clk = clk_get_rate(kmb_dsi->clk_mipi_ecfg); 1537 if (clk != KMB_MIPI_DEFAULT_CFG_CLK) { 1538 /* Set MIPI_ECFG clock to 24 Mhz */ 1539 clk_set_rate(kmb_dsi->clk_mipi_ecfg, KMB_MIPI_DEFAULT_CFG_CLK); 1540 clk = clk_get_rate(kmb_dsi->clk_mipi_ecfg); 1541 if (clk != KMB_MIPI_DEFAULT_CFG_CLK) { 1542 dev_err(dev, "failed to set to clk_mipi_ecfg to %d\n", 1543 KMB_MIPI_DEFAULT_CFG_CLK); 1544 return -1; 1545 } 1546 } 1547 1548 clk = clk_get_rate(kmb_dsi->clk_mipi_cfg); 1549 if (clk != KMB_MIPI_DEFAULT_CFG_CLK) { 1550 /* Set MIPI_CFG clock to 24 Mhz */ 1551 clk_set_rate(kmb_dsi->clk_mipi_cfg, 24000000); 1552 clk = clk_get_rate(kmb_dsi->clk_mipi_cfg); 1553 if (clk != KMB_MIPI_DEFAULT_CFG_CLK) { 1554 dev_err(dev, "failed to set clk_mipi_cfg to %d\n", 1555 KMB_MIPI_DEFAULT_CFG_CLK); 1556 return -1; 1557 } 1558 } 1559 1560 return kmb_dsi_clk_enable(kmb_dsi); 1561 } 1562