1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * TC358767/TC358867/TC9595 DSI/DPI-to-DPI/(e)DP bridge driver 4 * 5 * The TC358767/TC358867/TC9595 can operate in multiple modes. 6 * All modes are supported -- DPI->(e)DP / DSI->DPI / DSI->(e)DP . 7 * 8 * Copyright (C) 2016 CogentEmbedded Inc 9 * Author: Andrey Gusakov <andrey.gusakov@cogentembedded.com> 10 * 11 * Copyright (C) 2016 Pengutronix, Philipp Zabel <p.zabel@pengutronix.de> 12 * 13 * Copyright (C) 2016 Zodiac Inflight Innovations 14 * 15 * Initially based on: drivers/gpu/drm/i2c/tda998x_drv.c 16 * 17 * Copyright (C) 2012 Texas Instruments 18 * Author: Rob Clark <robdclark@gmail.com> 19 */ 20 21 #include <linux/bitfield.h> 22 #include <linux/clk.h> 23 #include <linux/device.h> 24 #include <linux/gpio/consumer.h> 25 #include <linux/i2c.h> 26 #include <linux/kernel.h> 27 #include <linux/media-bus-format.h> 28 #include <linux/module.h> 29 #include <linux/regmap.h> 30 #include <linux/slab.h> 31 32 #include <drm/display/drm_dp_helper.h> 33 #include <drm/drm_atomic_helper.h> 34 #include <drm/drm_bridge.h> 35 #include <drm/drm_edid.h> 36 #include <drm/drm_mipi_dsi.h> 37 #include <drm/drm_of.h> 38 #include <drm/drm_panel.h> 39 #include <drm/drm_print.h> 40 #include <drm/drm_probe_helper.h> 41 42 /* Registers */ 43 44 /* DSI D-PHY Layer registers */ 45 #define D0W_DPHYCONTTX 0x0004 46 #define CLW_DPHYCONTTX 0x0020 47 #define D0W_DPHYCONTRX 0x0024 48 #define D1W_DPHYCONTRX 0x0028 49 #define D2W_DPHYCONTRX 0x002c 50 #define D3W_DPHYCONTRX 0x0030 51 #define COM_DPHYCONTRX 0x0038 52 #define CLW_CNTRL 0x0040 53 #define D0W_CNTRL 0x0044 54 #define D1W_CNTRL 0x0048 55 #define D2W_CNTRL 0x004c 56 #define D3W_CNTRL 0x0050 57 #define TESTMODE_CNTRL 0x0054 58 59 /* PPI layer registers */ 60 #define PPI_STARTPPI 0x0104 /* START control bit */ 61 #define PPI_BUSYPPI 0x0108 /* PPI busy status */ 62 #define PPI_LPTXTIMECNT 0x0114 /* LPTX timing signal */ 63 #define LPX_PERIOD 3 64 #define PPI_LANEENABLE 0x0134 65 #define PPI_TX_RX_TA 0x013c 66 #define TTA_GET 0x40000 67 #define TTA_SURE 6 68 #define PPI_D0S_ATMR 0x0144 69 #define PPI_D1S_ATMR 0x0148 70 #define PPI_D0S_CLRSIPOCOUNT 0x0164 /* Assertion timer for Lane 0 */ 71 #define PPI_D1S_CLRSIPOCOUNT 0x0168 /* Assertion timer for Lane 1 */ 72 #define PPI_D2S_CLRSIPOCOUNT 0x016c /* Assertion timer for Lane 2 */ 73 #define PPI_D3S_CLRSIPOCOUNT 0x0170 /* Assertion timer for Lane 3 */ 74 #define PPI_START_FUNCTION BIT(0) 75 76 /* DSI layer registers */ 77 #define DSI_STARTDSI 0x0204 /* START control bit of DSI-TX */ 78 #define DSI_BUSYDSI 0x0208 /* DSI busy status */ 79 #define DSI_LANEENABLE 0x0210 /* Enables each lane */ 80 #define DSI_RX_START BIT(0) 81 82 /* Lane enable PPI and DSI register bits */ 83 #define LANEENABLE_CLEN BIT(0) 84 #define LANEENABLE_L0EN BIT(1) 85 #define LANEENABLE_L1EN BIT(2) 86 #define LANEENABLE_L2EN BIT(1) 87 #define LANEENABLE_L3EN BIT(2) 88 89 #define DSI_LANESTATUS0 0x0214 /* DSI lane status 0 */ 90 #define DSI_LANESTATUS1 0x0218 /* DSI lane status 1 */ 91 #define DSI_INTSTATUS 0x0220 /* Interrupt Status */ 92 #define DSI_INTMASK 0x0224 /* Interrupt Mask */ 93 #define DSI_INTCLR 0x0228 /* Interrupt Clear */ 94 #define DSI_LPTXTO 0x0230 /* LPTX Time Out Counter */ 95 96 /* DSI General Registers */ 97 #define DSIERRCNT 0x0300 /* DSI Error Count Register */ 98 99 /* DSI Application Layer Registers */ 100 #define APLCTRL 0x0400 /* Application layer Control Register */ 101 #define RDPKTLN 0x0404 /* DSI Read packet Length Register */ 102 103 /* Display Parallel Input Interface */ 104 #define DPIPXLFMT 0x0440 105 #define VS_POL_ACTIVE_LOW (1 << 10) 106 #define HS_POL_ACTIVE_LOW (1 << 9) 107 #define DE_POL_ACTIVE_HIGH (0 << 8) 108 #define SUB_CFG_TYPE_CONFIG1 (0 << 2) /* LSB aligned */ 109 #define SUB_CFG_TYPE_CONFIG2 (1 << 2) /* Loosely Packed */ 110 #define SUB_CFG_TYPE_CONFIG3 (2 << 2) /* LSB aligned 8-bit */ 111 #define DPI_BPP_RGB888 (0 << 0) 112 #define DPI_BPP_RGB666 (1 << 0) 113 #define DPI_BPP_RGB565 (2 << 0) 114 115 /* Display Parallel Output Interface */ 116 #define POCTRL 0x0448 117 #define POCTRL_S2P BIT(7) 118 #define POCTRL_PCLK_POL BIT(3) 119 #define POCTRL_VS_POL BIT(2) 120 #define POCTRL_HS_POL BIT(1) 121 #define POCTRL_DE_POL BIT(0) 122 123 /* Video Path */ 124 #define VPCTRL0 0x0450 125 #define VSDELAY GENMASK(31, 20) 126 #define OPXLFMT_RGB666 (0 << 8) 127 #define OPXLFMT_RGB888 (1 << 8) 128 #define FRMSYNC_DISABLED (0 << 4) /* Video Timing Gen Disabled */ 129 #define FRMSYNC_ENABLED (1 << 4) /* Video Timing Gen Enabled */ 130 #define MSF_DISABLED (0 << 0) /* Magic Square FRC disabled */ 131 #define MSF_ENABLED (1 << 0) /* Magic Square FRC enabled */ 132 #define HTIM01 0x0454 133 #define HPW GENMASK(8, 0) 134 #define HBPR GENMASK(24, 16) 135 #define HTIM02 0x0458 136 #define HDISPR GENMASK(10, 0) 137 #define HFPR GENMASK(24, 16) 138 #define VTIM01 0x045c 139 #define VSPR GENMASK(7, 0) 140 #define VBPR GENMASK(23, 16) 141 #define VTIM02 0x0460 142 #define VFPR GENMASK(23, 16) 143 #define VDISPR GENMASK(10, 0) 144 #define VFUEN0 0x0464 145 #define VFUEN BIT(0) /* Video Frame Timing Upload */ 146 147 /* System */ 148 #define TC_IDREG 0x0500 /* Chip ID and Revision ID */ 149 #define SYSBOOT 0x0504 /* System BootStrap Status Register */ 150 #define SYSSTAT 0x0508 /* System Status Register */ 151 #define SYSRSTENB 0x050c /* System Reset/Enable Register */ 152 #define ENBI2C (1 << 0) 153 #define ENBLCD0 (1 << 2) 154 #define ENBBM (1 << 3) 155 #define ENBDSIRX (1 << 4) 156 #define ENBREG (1 << 5) 157 #define ENBHDCP (1 << 8) 158 #define SYSCTRL 0x0510 /* System Control Register */ 159 #define DP0_AUDSRC_NO_INPUT (0 << 3) 160 #define DP0_AUDSRC_I2S_RX (1 << 3) 161 #define DP0_VIDSRC_NO_INPUT (0 << 0) 162 #define DP0_VIDSRC_DSI_RX (1 << 0) 163 #define DP0_VIDSRC_DPI_RX (2 << 0) 164 #define DP0_VIDSRC_COLOR_BAR (3 << 0) 165 #define GPIOM 0x0540 /* GPIO Mode Control Register */ 166 #define GPIOC 0x0544 /* GPIO Direction Control Register */ 167 #define GPIOO 0x0548 /* GPIO Output Register */ 168 #define GPIOI 0x054c /* GPIO Input Register */ 169 #define INTCTL_G 0x0560 /* General Interrupts Control Register */ 170 #define INTSTS_G 0x0564 /* General Interrupts Status Register */ 171 172 #define INT_SYSERR BIT(16) 173 #define INT_GPIO_H(x) (1 << (x == 0 ? 2 : 10)) 174 #define INT_GPIO_LC(x) (1 << (x == 0 ? 3 : 11)) 175 176 #define TEST_INT_C 0x0570 /* Test Interrupts Control Register */ 177 #define TEST_INT_S 0x0574 /* Test Interrupts Status Register */ 178 179 #define INT_GP0_LCNT 0x0584 /* Interrupt GPIO0 Low Count Value Register */ 180 #define INT_GP1_LCNT 0x0588 /* Interrupt GPIO1 Low Count Value Register */ 181 182 /* Control */ 183 #define DP0CTL 0x0600 184 #define VID_MN_GEN BIT(6) /* Auto-generate M/N values */ 185 #define EF_EN BIT(5) /* Enable Enhanced Framing */ 186 #define VID_EN BIT(1) /* Video transmission enable */ 187 #define DP_EN BIT(0) /* Enable DPTX function */ 188 189 /* Clocks */ 190 #define DP0_VIDMNGEN0 0x0610 /* DP0 Video Force M Value Register */ 191 #define DP0_VIDMNGEN1 0x0614 /* DP0 Video Force N Value Register */ 192 #define DP0_VMNGENSTATUS 0x0618 /* DP0 Video Current M Value Register */ 193 #define DP0_AUDMNGEN0 0x0628 /* DP0 Audio Force M Value Register */ 194 #define DP0_AUDMNGEN1 0x062c /* DP0 Audio Force N Value Register */ 195 #define DP0_AMNGENSTATUS 0x0630 /* DP0 Audio Current M Value Register */ 196 197 /* Main Channel */ 198 #define DP0_SECSAMPLE 0x0640 199 #define DP0_VIDSYNCDELAY 0x0644 200 #define VID_SYNC_DLY GENMASK(15, 0) 201 #define THRESH_DLY GENMASK(31, 16) 202 203 #define DP0_TOTALVAL 0x0648 204 #define H_TOTAL GENMASK(15, 0) 205 #define V_TOTAL GENMASK(31, 16) 206 #define DP0_STARTVAL 0x064c 207 #define H_START GENMASK(15, 0) 208 #define V_START GENMASK(31, 16) 209 #define DP0_ACTIVEVAL 0x0650 210 #define H_ACT GENMASK(15, 0) 211 #define V_ACT GENMASK(31, 16) 212 213 #define DP0_SYNCVAL 0x0654 214 #define VS_WIDTH GENMASK(30, 16) 215 #define HS_WIDTH GENMASK(14, 0) 216 #define SYNCVAL_HS_POL_ACTIVE_LOW (1 << 15) 217 #define SYNCVAL_VS_POL_ACTIVE_LOW (1 << 31) 218 #define DP0_MISC 0x0658 219 #define TU_SIZE_RECOMMENDED (63) /* LSCLK cycles per TU */ 220 #define MAX_TU_SYMBOL GENMASK(28, 23) 221 #define TU_SIZE GENMASK(21, 16) 222 #define BPC_6 (0 << 5) 223 #define BPC_8 (1 << 5) 224 225 /* AUX channel */ 226 #define DP0_AUXCFG0 0x0660 227 #define DP0_AUXCFG0_BSIZE GENMASK(11, 8) 228 #define DP0_AUXCFG0_ADDR_ONLY BIT(4) 229 #define DP0_AUXCFG1 0x0664 230 #define AUX_RX_FILTER_EN BIT(16) 231 232 #define DP0_AUXADDR 0x0668 233 #define DP0_AUXWDATA(i) (0x066c + (i) * 4) 234 #define DP0_AUXRDATA(i) (0x067c + (i) * 4) 235 #define DP0_AUXSTATUS 0x068c 236 #define AUX_BYTES GENMASK(15, 8) 237 #define AUX_STATUS GENMASK(7, 4) 238 #define AUX_TIMEOUT BIT(1) 239 #define AUX_BUSY BIT(0) 240 #define DP0_AUXI2CADR 0x0698 241 242 /* Link Training */ 243 #define DP0_SRCCTRL 0x06a0 244 #define DP0_SRCCTRL_SCRMBLDIS BIT(13) 245 #define DP0_SRCCTRL_EN810B BIT(12) 246 #define DP0_SRCCTRL_NOTP (0 << 8) 247 #define DP0_SRCCTRL_TP1 (1 << 8) 248 #define DP0_SRCCTRL_TP2 (2 << 8) 249 #define DP0_SRCCTRL_LANESKEW BIT(7) 250 #define DP0_SRCCTRL_SSCG BIT(3) 251 #define DP0_SRCCTRL_LANES_1 (0 << 2) 252 #define DP0_SRCCTRL_LANES_2 (1 << 2) 253 #define DP0_SRCCTRL_BW27 (1 << 1) 254 #define DP0_SRCCTRL_BW162 (0 << 1) 255 #define DP0_SRCCTRL_AUTOCORRECT BIT(0) 256 #define DP0_LTSTAT 0x06d0 257 #define LT_LOOPDONE BIT(13) 258 #define LT_STATUS_MASK (0x1f << 8) 259 #define LT_CHANNEL1_EQ_BITS (DP_CHANNEL_EQ_BITS << 4) 260 #define LT_INTERLANE_ALIGN_DONE BIT(3) 261 #define LT_CHANNEL0_EQ_BITS (DP_CHANNEL_EQ_BITS) 262 #define DP0_SNKLTCHGREQ 0x06d4 263 #define DP0_LTLOOPCTRL 0x06d8 264 #define DP0_SNKLTCTRL 0x06e4 265 #define DP0_TPATDAT0 0x06e8 /* DP0 Test Pattern bits 29 to 0 */ 266 #define DP0_TPATDAT1 0x06ec /* DP0 Test Pattern bits 59 to 30 */ 267 #define DP0_TPATDAT2 0x06f0 /* DP0 Test Pattern bits 89 to 60 */ 268 #define DP0_TPATDAT3 0x06f4 /* DP0 Test Pattern bits 119 to 90 */ 269 270 #define AUDCFG0 0x0700 /* DP0 Audio Config0 Register */ 271 #define AUDCFG1 0x0704 /* DP0 Audio Config1 Register */ 272 #define AUDIFDATA0 0x0708 /* DP0 Audio Info Frame Bytes 3 to 0 */ 273 #define AUDIFDATA1 0x070c /* DP0 Audio Info Frame Bytes 7 to 4 */ 274 #define AUDIFDATA2 0x0710 /* DP0 Audio Info Frame Bytes 11 to 8 */ 275 #define AUDIFDATA3 0x0714 /* DP0 Audio Info Frame Bytes 15 to 12 */ 276 #define AUDIFDATA4 0x0718 /* DP0 Audio Info Frame Bytes 19 to 16 */ 277 #define AUDIFDATA5 0x071c /* DP0 Audio Info Frame Bytes 23 to 20 */ 278 #define AUDIFDATA6 0x0720 /* DP0 Audio Info Frame Bytes 27 to 24 */ 279 280 #define DP1_SRCCTRL 0x07a0 /* DP1 Control Register */ 281 282 /* PHY */ 283 #define DP_PHY_CTRL 0x0800 284 #define DP_PHY_RST BIT(28) /* DP PHY Global Soft Reset */ 285 #define BGREN BIT(25) /* AUX PHY BGR Enable */ 286 #define PWR_SW_EN BIT(24) /* PHY Power Switch Enable */ 287 #define PHY_M1_RST BIT(12) /* Reset PHY1 Main Channel */ 288 #define PHY_RDY BIT(16) /* PHY Main Channels Ready */ 289 #define PHY_M0_RST BIT(8) /* Reset PHY0 Main Channel */ 290 #define PHY_2LANE BIT(2) /* PHY Enable 2 lanes */ 291 #define PHY_A0_EN BIT(1) /* PHY Aux Channel0 Enable */ 292 #define PHY_M0_EN BIT(0) /* PHY Main Channel0 Enable */ 293 #define DP_PHY_CFG_WR 0x0810 /* DP PHY Configuration Test Write Register */ 294 #define DP_PHY_CFG_RD 0x0814 /* DP PHY Configuration Test Read Register */ 295 #define DP0_AUX_PHY_CTRL 0x0820 /* DP0 AUX PHY Control Register */ 296 #define DP0_MAIN_PHY_DBG 0x0840 /* DP0 Main PHY Test Debug Register */ 297 298 /* I2S */ 299 #define I2SCFG 0x0880 /* I2S Audio Config 0 Register */ 300 #define I2SCH0STAT0 0x0888 /* I2S Audio Channel 0 Status Bytes 3 to 0 */ 301 #define I2SCH0STAT1 0x088c /* I2S Audio Channel 0 Status Bytes 7 to 4 */ 302 #define I2SCH0STAT2 0x0890 /* I2S Audio Channel 0 Status Bytes 11 to 8 */ 303 #define I2SCH0STAT3 0x0894 /* I2S Audio Channel 0 Status Bytes 15 to 12 */ 304 #define I2SCH0STAT4 0x0898 /* I2S Audio Channel 0 Status Bytes 19 to 16 */ 305 #define I2SCH0STAT5 0x089c /* I2S Audio Channel 0 Status Bytes 23 to 20 */ 306 #define I2SCH1STAT0 0x08a0 /* I2S Audio Channel 1 Status Bytes 3 to 0 */ 307 #define I2SCH1STAT1 0x08a4 /* I2S Audio Channel 1 Status Bytes 7 to 4 */ 308 #define I2SCH1STAT2 0x08a8 /* I2S Audio Channel 1 Status Bytes 11 to 8 */ 309 #define I2SCH1STAT3 0x08ac /* I2S Audio Channel 1 Status Bytes 15 to 12 */ 310 #define I2SCH1STAT4 0x08b0 /* I2S Audio Channel 1 Status Bytes 19 to 16 */ 311 #define I2SCH1STAT5 0x08b4 /* I2S Audio Channel 1 Status Bytes 23 to 20 */ 312 313 /* PLL */ 314 #define DP0_PLLCTRL 0x0900 315 #define DP1_PLLCTRL 0x0904 /* not defined in DS */ 316 #define PXL_PLLCTRL 0x0908 317 #define PLLUPDATE BIT(2) 318 #define PLLBYP BIT(1) 319 #define PLLEN BIT(0) 320 #define PXL_PLLPARAM 0x0914 321 #define IN_SEL_REFCLK (0 << 14) 322 #define SYS_PLLPARAM 0x0918 323 #define REF_FREQ_38M4 (0 << 8) /* 38.4 MHz */ 324 #define REF_FREQ_19M2 (1 << 8) /* 19.2 MHz */ 325 #define REF_FREQ_26M (2 << 8) /* 26 MHz */ 326 #define REF_FREQ_13M (3 << 8) /* 13 MHz */ 327 #define SYSCLK_SEL_LSCLK (0 << 4) 328 #define LSCLK_DIV_1 (0 << 0) 329 #define LSCLK_DIV_2 (1 << 0) 330 331 /* Test & Debug */ 332 #define TSTCTL 0x0a00 333 #define COLOR_R GENMASK(31, 24) 334 #define COLOR_G GENMASK(23, 16) 335 #define COLOR_B GENMASK(15, 8) 336 #define ENI2CFILTER BIT(4) 337 #define COLOR_BAR_MODE GENMASK(1, 0) 338 #define COLOR_BAR_MODE_BARS 2 339 #define PLL_DBG 0x0a04 340 341 static bool tc_test_pattern; 342 module_param_named(test, tc_test_pattern, bool, 0644); 343 344 struct tc_edp_link { 345 u8 dpcd[DP_RECEIVER_CAP_SIZE]; 346 unsigned int rate; 347 u8 num_lanes; 348 u8 assr; 349 bool scrambler_dis; 350 bool spread; 351 }; 352 353 struct tc_data { 354 struct device *dev; 355 struct regmap *regmap; 356 struct drm_dp_aux aux; 357 358 struct drm_bridge bridge; 359 struct drm_bridge *panel_bridge; 360 struct drm_connector connector; 361 362 struct mipi_dsi_device *dsi; 363 364 /* link settings */ 365 struct tc_edp_link link; 366 367 /* current mode */ 368 struct drm_display_mode mode; 369 370 u32 rev; 371 u8 assr; 372 373 struct gpio_desc *sd_gpio; 374 struct gpio_desc *reset_gpio; 375 struct clk *refclk; 376 377 /* do we have IRQ */ 378 bool have_irq; 379 380 /* Input connector type, DSI and not DPI. */ 381 bool input_connector_dsi; 382 383 /* HPD pin number (0 or 1) or -ENODEV */ 384 int hpd_pin; 385 }; 386 387 static inline struct tc_data *aux_to_tc(struct drm_dp_aux *a) 388 { 389 return container_of(a, struct tc_data, aux); 390 } 391 392 static inline struct tc_data *bridge_to_tc(struct drm_bridge *b) 393 { 394 return container_of(b, struct tc_data, bridge); 395 } 396 397 static inline struct tc_data *connector_to_tc(struct drm_connector *c) 398 { 399 return container_of(c, struct tc_data, connector); 400 } 401 402 static inline int tc_poll_timeout(struct tc_data *tc, unsigned int addr, 403 unsigned int cond_mask, 404 unsigned int cond_value, 405 unsigned long sleep_us, u64 timeout_us) 406 { 407 unsigned int val; 408 409 return regmap_read_poll_timeout(tc->regmap, addr, val, 410 (val & cond_mask) == cond_value, 411 sleep_us, timeout_us); 412 } 413 414 static int tc_aux_wait_busy(struct tc_data *tc) 415 { 416 return tc_poll_timeout(tc, DP0_AUXSTATUS, AUX_BUSY, 0, 100, 100000); 417 } 418 419 static int tc_aux_write_data(struct tc_data *tc, const void *data, 420 size_t size) 421 { 422 u32 auxwdata[DP_AUX_MAX_PAYLOAD_BYTES / sizeof(u32)] = { 0 }; 423 int ret, count = ALIGN(size, sizeof(u32)); 424 425 memcpy(auxwdata, data, size); 426 427 ret = regmap_raw_write(tc->regmap, DP0_AUXWDATA(0), auxwdata, count); 428 if (ret) 429 return ret; 430 431 return size; 432 } 433 434 static int tc_aux_read_data(struct tc_data *tc, void *data, size_t size) 435 { 436 u32 auxrdata[DP_AUX_MAX_PAYLOAD_BYTES / sizeof(u32)]; 437 int ret, count = ALIGN(size, sizeof(u32)); 438 439 ret = regmap_raw_read(tc->regmap, DP0_AUXRDATA(0), auxrdata, count); 440 if (ret) 441 return ret; 442 443 memcpy(data, auxrdata, size); 444 445 return size; 446 } 447 448 static u32 tc_auxcfg0(struct drm_dp_aux_msg *msg, size_t size) 449 { 450 u32 auxcfg0 = msg->request; 451 452 if (size) 453 auxcfg0 |= FIELD_PREP(DP0_AUXCFG0_BSIZE, size - 1); 454 else 455 auxcfg0 |= DP0_AUXCFG0_ADDR_ONLY; 456 457 return auxcfg0; 458 } 459 460 static ssize_t tc_aux_transfer(struct drm_dp_aux *aux, 461 struct drm_dp_aux_msg *msg) 462 { 463 struct tc_data *tc = aux_to_tc(aux); 464 size_t size = min_t(size_t, DP_AUX_MAX_PAYLOAD_BYTES - 1, msg->size); 465 u8 request = msg->request & ~DP_AUX_I2C_MOT; 466 u32 auxstatus; 467 int ret; 468 469 ret = tc_aux_wait_busy(tc); 470 if (ret) 471 return ret; 472 473 switch (request) { 474 case DP_AUX_NATIVE_READ: 475 case DP_AUX_I2C_READ: 476 break; 477 case DP_AUX_NATIVE_WRITE: 478 case DP_AUX_I2C_WRITE: 479 if (size) { 480 ret = tc_aux_write_data(tc, msg->buffer, size); 481 if (ret < 0) 482 return ret; 483 } 484 break; 485 default: 486 return -EINVAL; 487 } 488 489 /* Store address */ 490 ret = regmap_write(tc->regmap, DP0_AUXADDR, msg->address); 491 if (ret) 492 return ret; 493 /* Start transfer */ 494 ret = regmap_write(tc->regmap, DP0_AUXCFG0, tc_auxcfg0(msg, size)); 495 if (ret) 496 return ret; 497 498 ret = tc_aux_wait_busy(tc); 499 if (ret) 500 return ret; 501 502 ret = regmap_read(tc->regmap, DP0_AUXSTATUS, &auxstatus); 503 if (ret) 504 return ret; 505 506 if (auxstatus & AUX_TIMEOUT) 507 return -ETIMEDOUT; 508 /* 509 * For some reason address-only DP_AUX_I2C_WRITE (MOT), still 510 * reports 1 byte transferred in its status. To deal we that 511 * we ignore aux_bytes field if we know that this was an 512 * address-only transfer 513 */ 514 if (size) 515 size = FIELD_GET(AUX_BYTES, auxstatus); 516 msg->reply = FIELD_GET(AUX_STATUS, auxstatus); 517 518 switch (request) { 519 case DP_AUX_NATIVE_READ: 520 case DP_AUX_I2C_READ: 521 if (size) 522 return tc_aux_read_data(tc, msg->buffer, size); 523 break; 524 } 525 526 return size; 527 } 528 529 static const char * const training_pattern1_errors[] = { 530 "No errors", 531 "Aux write error", 532 "Aux read error", 533 "Max voltage reached error", 534 "Loop counter expired error", 535 "res", "res", "res" 536 }; 537 538 static const char * const training_pattern2_errors[] = { 539 "No errors", 540 "Aux write error", 541 "Aux read error", 542 "Clock recovery failed error", 543 "Loop counter expired error", 544 "res", "res", "res" 545 }; 546 547 static u32 tc_srcctrl(struct tc_data *tc) 548 { 549 /* 550 * No training pattern, skew lane 1 data by two LSCLK cycles with 551 * respect to lane 0 data, AutoCorrect Mode = 0 552 */ 553 u32 reg = DP0_SRCCTRL_NOTP | DP0_SRCCTRL_LANESKEW | DP0_SRCCTRL_EN810B; 554 555 if (tc->link.scrambler_dis) 556 reg |= DP0_SRCCTRL_SCRMBLDIS; /* Scrambler Disabled */ 557 if (tc->link.spread) 558 reg |= DP0_SRCCTRL_SSCG; /* Spread Spectrum Enable */ 559 if (tc->link.num_lanes == 2) 560 reg |= DP0_SRCCTRL_LANES_2; /* Two Main Channel Lanes */ 561 if (tc->link.rate != 162000) 562 reg |= DP0_SRCCTRL_BW27; /* 2.7 Gbps link */ 563 return reg; 564 } 565 566 static int tc_pllupdate(struct tc_data *tc, unsigned int pllctrl) 567 { 568 int ret; 569 570 ret = regmap_write(tc->regmap, pllctrl, PLLUPDATE | PLLEN); 571 if (ret) 572 return ret; 573 574 /* Wait for PLL to lock: up to 7.5 ms, depending on refclk */ 575 usleep_range(15000, 20000); 576 577 return 0; 578 } 579 580 static int tc_pxl_pll_en(struct tc_data *tc, u32 refclk, u32 pixelclock) 581 { 582 int ret; 583 int i_pre, best_pre = 1; 584 int i_post, best_post = 1; 585 int div, best_div = 1; 586 int mul, best_mul = 1; 587 int delta, best_delta; 588 int ext_div[] = {1, 2, 3, 5, 7}; 589 int clk_min, clk_max; 590 int best_pixelclock = 0; 591 int vco_hi = 0; 592 u32 pxl_pllparam; 593 594 /* 595 * refclk * mul / (ext_pre_div * pre_div) should be in range: 596 * - DPI ..... 0 to 100 MHz 597 * - (e)DP ... 150 to 650 MHz 598 */ 599 if (tc->bridge.type == DRM_MODE_CONNECTOR_DPI) { 600 clk_min = 0; 601 clk_max = 100000000; 602 } else { 603 clk_min = 150000000; 604 clk_max = 650000000; 605 } 606 607 dev_dbg(tc->dev, "PLL: requested %d pixelclock, ref %d\n", pixelclock, 608 refclk); 609 best_delta = pixelclock; 610 /* Loop over all possible ext_divs, skipping invalid configurations */ 611 for (i_pre = 0; i_pre < ARRAY_SIZE(ext_div); i_pre++) { 612 /* 613 * refclk / ext_pre_div should be in the 1 to 200 MHz range. 614 * We don't allow any refclk > 200 MHz, only check lower bounds. 615 */ 616 if (refclk / ext_div[i_pre] < 1000000) 617 continue; 618 for (i_post = 0; i_post < ARRAY_SIZE(ext_div); i_post++) { 619 for (div = 1; div <= 16; div++) { 620 u32 clk, iclk; 621 u64 tmp; 622 623 /* PCLK PLL input unit clock ... 6..40 MHz */ 624 iclk = refclk / (div * ext_div[i_pre]); 625 if (iclk < 6000000 || iclk > 40000000) 626 continue; 627 628 tmp = pixelclock * ext_div[i_pre] * 629 ext_div[i_post] * div; 630 do_div(tmp, refclk); 631 mul = tmp; 632 633 /* Check limits */ 634 if ((mul < 1) || (mul > 128)) 635 continue; 636 637 clk = (refclk / ext_div[i_pre] / div) * mul; 638 if ((clk > clk_max) || (clk < clk_min)) 639 continue; 640 641 clk = clk / ext_div[i_post]; 642 delta = clk - pixelclock; 643 644 if (abs(delta) < abs(best_delta)) { 645 best_pre = i_pre; 646 best_post = i_post; 647 best_div = div; 648 best_mul = mul; 649 best_delta = delta; 650 best_pixelclock = clk; 651 } 652 } 653 } 654 } 655 if (best_pixelclock == 0) { 656 dev_err(tc->dev, "Failed to calc clock for %d pixelclock\n", 657 pixelclock); 658 return -EINVAL; 659 } 660 661 dev_dbg(tc->dev, "PLL: got %d, delta %d\n", best_pixelclock, 662 best_delta); 663 dev_dbg(tc->dev, "PLL: %d / %d / %d * %d / %d\n", refclk, 664 ext_div[best_pre], best_div, best_mul, ext_div[best_post]); 665 666 /* if VCO >= 300 MHz */ 667 if (refclk / ext_div[best_pre] / best_div * best_mul >= 300000000) 668 vco_hi = 1; 669 /* see DS */ 670 if (best_div == 16) 671 best_div = 0; 672 if (best_mul == 128) 673 best_mul = 0; 674 675 /* Power up PLL and switch to bypass */ 676 ret = regmap_write(tc->regmap, PXL_PLLCTRL, PLLBYP | PLLEN); 677 if (ret) 678 return ret; 679 680 pxl_pllparam = vco_hi << 24; /* For PLL VCO >= 300 MHz = 1 */ 681 pxl_pllparam |= ext_div[best_pre] << 20; /* External Pre-divider */ 682 pxl_pllparam |= ext_div[best_post] << 16; /* External Post-divider */ 683 pxl_pllparam |= IN_SEL_REFCLK; /* Use RefClk as PLL input */ 684 pxl_pllparam |= best_div << 8; /* Divider for PLL RefClk */ 685 pxl_pllparam |= best_mul; /* Multiplier for PLL */ 686 687 ret = regmap_write(tc->regmap, PXL_PLLPARAM, pxl_pllparam); 688 if (ret) 689 return ret; 690 691 /* Force PLL parameter update and disable bypass */ 692 return tc_pllupdate(tc, PXL_PLLCTRL); 693 } 694 695 static int tc_pxl_pll_dis(struct tc_data *tc) 696 { 697 /* Enable PLL bypass, power down PLL */ 698 return regmap_write(tc->regmap, PXL_PLLCTRL, PLLBYP); 699 } 700 701 static int tc_stream_clock_calc(struct tc_data *tc) 702 { 703 /* 704 * If the Stream clock and Link Symbol clock are 705 * asynchronous with each other, the value of M changes over 706 * time. This way of generating link clock and stream 707 * clock is called Asynchronous Clock mode. The value M 708 * must change while the value N stays constant. The 709 * value of N in this Asynchronous Clock mode must be set 710 * to 2^15 or 32,768. 711 * 712 * LSCLK = 1/10 of high speed link clock 713 * 714 * f_STRMCLK = M/N * f_LSCLK 715 * M/N = f_STRMCLK / f_LSCLK 716 * 717 */ 718 return regmap_write(tc->regmap, DP0_VIDMNGEN1, 32768); 719 } 720 721 static int tc_set_syspllparam(struct tc_data *tc) 722 { 723 unsigned long rate; 724 u32 pllparam = SYSCLK_SEL_LSCLK | LSCLK_DIV_2; 725 726 rate = clk_get_rate(tc->refclk); 727 switch (rate) { 728 case 38400000: 729 pllparam |= REF_FREQ_38M4; 730 break; 731 case 26000000: 732 pllparam |= REF_FREQ_26M; 733 break; 734 case 19200000: 735 pllparam |= REF_FREQ_19M2; 736 break; 737 case 13000000: 738 pllparam |= REF_FREQ_13M; 739 break; 740 default: 741 dev_err(tc->dev, "Invalid refclk rate: %lu Hz\n", rate); 742 return -EINVAL; 743 } 744 745 return regmap_write(tc->regmap, SYS_PLLPARAM, pllparam); 746 } 747 748 static int tc_aux_link_setup(struct tc_data *tc) 749 { 750 int ret; 751 u32 dp0_auxcfg1; 752 753 /* Setup DP-PHY / PLL */ 754 ret = tc_set_syspllparam(tc); 755 if (ret) 756 goto err; 757 758 ret = regmap_write(tc->regmap, DP_PHY_CTRL, 759 BGREN | PWR_SW_EN | PHY_A0_EN); 760 if (ret) 761 goto err; 762 /* 763 * Initially PLLs are in bypass. Force PLL parameter update, 764 * disable PLL bypass, enable PLL 765 */ 766 ret = tc_pllupdate(tc, DP0_PLLCTRL); 767 if (ret) 768 goto err; 769 770 ret = tc_pllupdate(tc, DP1_PLLCTRL); 771 if (ret) 772 goto err; 773 774 ret = tc_poll_timeout(tc, DP_PHY_CTRL, PHY_RDY, PHY_RDY, 100, 100000); 775 if (ret == -ETIMEDOUT) { 776 dev_err(tc->dev, "Timeout waiting for PHY to become ready"); 777 return ret; 778 } else if (ret) { 779 goto err; 780 } 781 782 /* Setup AUX link */ 783 dp0_auxcfg1 = AUX_RX_FILTER_EN; 784 dp0_auxcfg1 |= 0x06 << 8; /* Aux Bit Period Calculator Threshold */ 785 dp0_auxcfg1 |= 0x3f << 0; /* Aux Response Timeout Timer */ 786 787 ret = regmap_write(tc->regmap, DP0_AUXCFG1, dp0_auxcfg1); 788 if (ret) 789 goto err; 790 791 /* Register DP AUX channel */ 792 tc->aux.name = "TC358767 AUX i2c adapter"; 793 tc->aux.dev = tc->dev; 794 tc->aux.transfer = tc_aux_transfer; 795 drm_dp_aux_init(&tc->aux); 796 797 return 0; 798 err: 799 dev_err(tc->dev, "tc_aux_link_setup failed: %d\n", ret); 800 return ret; 801 } 802 803 static int tc_get_display_props(struct tc_data *tc) 804 { 805 u8 revision, num_lanes; 806 unsigned int rate; 807 int ret; 808 u8 reg; 809 810 /* Read DP Rx Link Capability */ 811 ret = drm_dp_dpcd_read(&tc->aux, DP_DPCD_REV, tc->link.dpcd, 812 DP_RECEIVER_CAP_SIZE); 813 if (ret < 0) 814 goto err_dpcd_read; 815 816 revision = tc->link.dpcd[DP_DPCD_REV]; 817 rate = drm_dp_max_link_rate(tc->link.dpcd); 818 num_lanes = drm_dp_max_lane_count(tc->link.dpcd); 819 820 if (rate != 162000 && rate != 270000) { 821 dev_dbg(tc->dev, "Falling to 2.7 Gbps rate\n"); 822 rate = 270000; 823 } 824 825 tc->link.rate = rate; 826 827 if (num_lanes > 2) { 828 dev_dbg(tc->dev, "Falling to 2 lanes\n"); 829 num_lanes = 2; 830 } 831 832 tc->link.num_lanes = num_lanes; 833 834 ret = drm_dp_dpcd_readb(&tc->aux, DP_MAX_DOWNSPREAD, ®); 835 if (ret < 0) 836 goto err_dpcd_read; 837 tc->link.spread = reg & DP_MAX_DOWNSPREAD_0_5; 838 839 ret = drm_dp_dpcd_readb(&tc->aux, DP_MAIN_LINK_CHANNEL_CODING, ®); 840 if (ret < 0) 841 goto err_dpcd_read; 842 843 tc->link.scrambler_dis = false; 844 /* read assr */ 845 ret = drm_dp_dpcd_readb(&tc->aux, DP_EDP_CONFIGURATION_SET, ®); 846 if (ret < 0) 847 goto err_dpcd_read; 848 tc->link.assr = reg & DP_ALTERNATE_SCRAMBLER_RESET_ENABLE; 849 850 dev_dbg(tc->dev, "DPCD rev: %d.%d, rate: %s, lanes: %d, framing: %s\n", 851 revision >> 4, revision & 0x0f, 852 (tc->link.rate == 162000) ? "1.62Gbps" : "2.7Gbps", 853 tc->link.num_lanes, 854 drm_dp_enhanced_frame_cap(tc->link.dpcd) ? 855 "enhanced" : "default"); 856 dev_dbg(tc->dev, "Downspread: %s, scrambler: %s\n", 857 tc->link.spread ? "0.5%" : "0.0%", 858 tc->link.scrambler_dis ? "disabled" : "enabled"); 859 dev_dbg(tc->dev, "Display ASSR: %d, TC358767 ASSR: %d\n", 860 tc->link.assr, tc->assr); 861 862 return 0; 863 864 err_dpcd_read: 865 dev_err(tc->dev, "failed to read DPCD: %d\n", ret); 866 return ret; 867 } 868 869 static int tc_set_common_video_mode(struct tc_data *tc, 870 const struct drm_display_mode *mode) 871 { 872 int left_margin = mode->htotal - mode->hsync_end; 873 int right_margin = mode->hsync_start - mode->hdisplay; 874 int hsync_len = mode->hsync_end - mode->hsync_start; 875 int upper_margin = mode->vtotal - mode->vsync_end; 876 int lower_margin = mode->vsync_start - mode->vdisplay; 877 int vsync_len = mode->vsync_end - mode->vsync_start; 878 int ret; 879 880 dev_dbg(tc->dev, "set mode %dx%d\n", 881 mode->hdisplay, mode->vdisplay); 882 dev_dbg(tc->dev, "H margin %d,%d sync %d\n", 883 left_margin, right_margin, hsync_len); 884 dev_dbg(tc->dev, "V margin %d,%d sync %d\n", 885 upper_margin, lower_margin, vsync_len); 886 dev_dbg(tc->dev, "total: %dx%d\n", mode->htotal, mode->vtotal); 887 888 889 /* 890 * LCD Ctl Frame Size 891 * datasheet is not clear of vsdelay in case of DPI 892 * assume we do not need any delay when DPI is a source of 893 * sync signals 894 */ 895 ret = regmap_write(tc->regmap, VPCTRL0, 896 FIELD_PREP(VSDELAY, right_margin + 10) | 897 OPXLFMT_RGB888 | FRMSYNC_DISABLED | MSF_DISABLED); 898 if (ret) 899 return ret; 900 901 ret = regmap_write(tc->regmap, HTIM01, 902 FIELD_PREP(HBPR, ALIGN(left_margin, 2)) | 903 FIELD_PREP(HPW, ALIGN(hsync_len, 2))); 904 if (ret) 905 return ret; 906 907 ret = regmap_write(tc->regmap, HTIM02, 908 FIELD_PREP(HDISPR, ALIGN(mode->hdisplay, 2)) | 909 FIELD_PREP(HFPR, ALIGN(right_margin, 2))); 910 if (ret) 911 return ret; 912 913 ret = regmap_write(tc->regmap, VTIM01, 914 FIELD_PREP(VBPR, upper_margin) | 915 FIELD_PREP(VSPR, vsync_len)); 916 if (ret) 917 return ret; 918 919 ret = regmap_write(tc->regmap, VTIM02, 920 FIELD_PREP(VFPR, lower_margin) | 921 FIELD_PREP(VDISPR, mode->vdisplay)); 922 if (ret) 923 return ret; 924 925 ret = regmap_write(tc->regmap, VFUEN0, VFUEN); /* update settings */ 926 if (ret) 927 return ret; 928 929 /* Test pattern settings */ 930 ret = regmap_write(tc->regmap, TSTCTL, 931 FIELD_PREP(COLOR_R, 120) | 932 FIELD_PREP(COLOR_G, 20) | 933 FIELD_PREP(COLOR_B, 99) | 934 ENI2CFILTER | 935 FIELD_PREP(COLOR_BAR_MODE, COLOR_BAR_MODE_BARS)); 936 937 return ret; 938 } 939 940 static int tc_set_dpi_video_mode(struct tc_data *tc, 941 const struct drm_display_mode *mode) 942 { 943 u32 value = POCTRL_S2P; 944 945 if (tc->mode.flags & DRM_MODE_FLAG_NHSYNC) 946 value |= POCTRL_HS_POL; 947 948 if (tc->mode.flags & DRM_MODE_FLAG_NVSYNC) 949 value |= POCTRL_VS_POL; 950 951 return regmap_write(tc->regmap, POCTRL, value); 952 } 953 954 static int tc_set_edp_video_mode(struct tc_data *tc, 955 const struct drm_display_mode *mode) 956 { 957 int ret; 958 int vid_sync_dly; 959 int max_tu_symbol; 960 961 int left_margin = mode->htotal - mode->hsync_end; 962 int hsync_len = mode->hsync_end - mode->hsync_start; 963 int upper_margin = mode->vtotal - mode->vsync_end; 964 int vsync_len = mode->vsync_end - mode->vsync_start; 965 u32 dp0_syncval; 966 u32 bits_per_pixel = 24; 967 u32 in_bw, out_bw; 968 u32 dpipxlfmt; 969 970 /* 971 * Recommended maximum number of symbols transferred in a transfer unit: 972 * DIV_ROUND_UP((input active video bandwidth in bytes) * tu_size, 973 * (output active video bandwidth in bytes)) 974 * Must be less than tu_size. 975 */ 976 977 in_bw = mode->clock * bits_per_pixel / 8; 978 out_bw = tc->link.num_lanes * tc->link.rate; 979 max_tu_symbol = DIV_ROUND_UP(in_bw * TU_SIZE_RECOMMENDED, out_bw); 980 981 /* DP Main Stream Attributes */ 982 vid_sync_dly = hsync_len + left_margin + mode->hdisplay; 983 ret = regmap_write(tc->regmap, DP0_VIDSYNCDELAY, 984 FIELD_PREP(THRESH_DLY, max_tu_symbol) | 985 FIELD_PREP(VID_SYNC_DLY, vid_sync_dly)); 986 987 ret = regmap_write(tc->regmap, DP0_TOTALVAL, 988 FIELD_PREP(H_TOTAL, mode->htotal) | 989 FIELD_PREP(V_TOTAL, mode->vtotal)); 990 if (ret) 991 return ret; 992 993 ret = regmap_write(tc->regmap, DP0_STARTVAL, 994 FIELD_PREP(H_START, left_margin + hsync_len) | 995 FIELD_PREP(V_START, upper_margin + vsync_len)); 996 if (ret) 997 return ret; 998 999 ret = regmap_write(tc->regmap, DP0_ACTIVEVAL, 1000 FIELD_PREP(V_ACT, mode->vdisplay) | 1001 FIELD_PREP(H_ACT, mode->hdisplay)); 1002 if (ret) 1003 return ret; 1004 1005 dp0_syncval = FIELD_PREP(VS_WIDTH, vsync_len) | 1006 FIELD_PREP(HS_WIDTH, hsync_len); 1007 1008 if (mode->flags & DRM_MODE_FLAG_NVSYNC) 1009 dp0_syncval |= SYNCVAL_VS_POL_ACTIVE_LOW; 1010 1011 if (mode->flags & DRM_MODE_FLAG_NHSYNC) 1012 dp0_syncval |= SYNCVAL_HS_POL_ACTIVE_LOW; 1013 1014 ret = regmap_write(tc->regmap, DP0_SYNCVAL, dp0_syncval); 1015 if (ret) 1016 return ret; 1017 1018 dpipxlfmt = DE_POL_ACTIVE_HIGH | SUB_CFG_TYPE_CONFIG1 | DPI_BPP_RGB888; 1019 1020 if (mode->flags & DRM_MODE_FLAG_NVSYNC) 1021 dpipxlfmt |= VS_POL_ACTIVE_LOW; 1022 1023 if (mode->flags & DRM_MODE_FLAG_NHSYNC) 1024 dpipxlfmt |= HS_POL_ACTIVE_LOW; 1025 1026 ret = regmap_write(tc->regmap, DPIPXLFMT, dpipxlfmt); 1027 if (ret) 1028 return ret; 1029 1030 ret = regmap_write(tc->regmap, DP0_MISC, 1031 FIELD_PREP(MAX_TU_SYMBOL, max_tu_symbol) | 1032 FIELD_PREP(TU_SIZE, TU_SIZE_RECOMMENDED) | 1033 BPC_8); 1034 return ret; 1035 } 1036 1037 static int tc_wait_link_training(struct tc_data *tc) 1038 { 1039 u32 value; 1040 int ret; 1041 1042 ret = tc_poll_timeout(tc, DP0_LTSTAT, LT_LOOPDONE, 1043 LT_LOOPDONE, 500, 100000); 1044 if (ret) { 1045 dev_err(tc->dev, "Link training timeout waiting for LT_LOOPDONE!\n"); 1046 return ret; 1047 } 1048 1049 ret = regmap_read(tc->regmap, DP0_LTSTAT, &value); 1050 if (ret) 1051 return ret; 1052 1053 return (value >> 8) & 0x7; 1054 } 1055 1056 static int tc_main_link_enable(struct tc_data *tc) 1057 { 1058 struct drm_dp_aux *aux = &tc->aux; 1059 struct device *dev = tc->dev; 1060 u32 dp_phy_ctrl; 1061 u32 value; 1062 int ret; 1063 u8 tmp[DP_LINK_STATUS_SIZE]; 1064 1065 dev_dbg(tc->dev, "link enable\n"); 1066 1067 ret = regmap_read(tc->regmap, DP0CTL, &value); 1068 if (ret) 1069 return ret; 1070 1071 if (WARN_ON(value & DP_EN)) { 1072 ret = regmap_write(tc->regmap, DP0CTL, 0); 1073 if (ret) 1074 return ret; 1075 } 1076 1077 ret = regmap_write(tc->regmap, DP0_SRCCTRL, tc_srcctrl(tc)); 1078 if (ret) 1079 return ret; 1080 /* SSCG and BW27 on DP1 must be set to the same as on DP0 */ 1081 ret = regmap_write(tc->regmap, DP1_SRCCTRL, 1082 (tc->link.spread ? DP0_SRCCTRL_SSCG : 0) | 1083 ((tc->link.rate != 162000) ? DP0_SRCCTRL_BW27 : 0)); 1084 if (ret) 1085 return ret; 1086 1087 ret = tc_set_syspllparam(tc); 1088 if (ret) 1089 return ret; 1090 1091 /* Setup Main Link */ 1092 dp_phy_ctrl = BGREN | PWR_SW_EN | PHY_A0_EN | PHY_M0_EN; 1093 if (tc->link.num_lanes == 2) 1094 dp_phy_ctrl |= PHY_2LANE; 1095 1096 ret = regmap_write(tc->regmap, DP_PHY_CTRL, dp_phy_ctrl); 1097 if (ret) 1098 return ret; 1099 1100 /* PLL setup */ 1101 ret = tc_pllupdate(tc, DP0_PLLCTRL); 1102 if (ret) 1103 return ret; 1104 1105 ret = tc_pllupdate(tc, DP1_PLLCTRL); 1106 if (ret) 1107 return ret; 1108 1109 /* Reset/Enable Main Links */ 1110 dp_phy_ctrl |= DP_PHY_RST | PHY_M1_RST | PHY_M0_RST; 1111 ret = regmap_write(tc->regmap, DP_PHY_CTRL, dp_phy_ctrl); 1112 usleep_range(100, 200); 1113 dp_phy_ctrl &= ~(DP_PHY_RST | PHY_M1_RST | PHY_M0_RST); 1114 ret = regmap_write(tc->regmap, DP_PHY_CTRL, dp_phy_ctrl); 1115 1116 ret = tc_poll_timeout(tc, DP_PHY_CTRL, PHY_RDY, PHY_RDY, 500, 100000); 1117 if (ret) { 1118 dev_err(dev, "timeout waiting for phy become ready"); 1119 return ret; 1120 } 1121 1122 /* Set misc: 8 bits per color */ 1123 ret = regmap_update_bits(tc->regmap, DP0_MISC, BPC_8, BPC_8); 1124 if (ret) 1125 return ret; 1126 1127 /* 1128 * ASSR mode 1129 * on TC358767 side ASSR configured through strap pin 1130 * seems there is no way to change this setting from SW 1131 * 1132 * check is tc configured for same mode 1133 */ 1134 if (tc->assr != tc->link.assr) { 1135 dev_dbg(dev, "Trying to set display to ASSR: %d\n", 1136 tc->assr); 1137 /* try to set ASSR on display side */ 1138 tmp[0] = tc->assr; 1139 ret = drm_dp_dpcd_writeb(aux, DP_EDP_CONFIGURATION_SET, tmp[0]); 1140 if (ret < 0) 1141 goto err_dpcd_read; 1142 /* read back */ 1143 ret = drm_dp_dpcd_readb(aux, DP_EDP_CONFIGURATION_SET, tmp); 1144 if (ret < 0) 1145 goto err_dpcd_read; 1146 1147 if (tmp[0] != tc->assr) { 1148 dev_dbg(dev, "Failed to switch display ASSR to %d, falling back to unscrambled mode\n", 1149 tc->assr); 1150 /* trying with disabled scrambler */ 1151 tc->link.scrambler_dis = true; 1152 } 1153 } 1154 1155 /* Setup Link & DPRx Config for Training */ 1156 tmp[0] = drm_dp_link_rate_to_bw_code(tc->link.rate); 1157 tmp[1] = tc->link.num_lanes; 1158 1159 if (drm_dp_enhanced_frame_cap(tc->link.dpcd)) 1160 tmp[1] |= DP_LANE_COUNT_ENHANCED_FRAME_EN; 1161 1162 ret = drm_dp_dpcd_write(aux, DP_LINK_BW_SET, tmp, 2); 1163 if (ret < 0) 1164 goto err_dpcd_write; 1165 1166 /* DOWNSPREAD_CTRL */ 1167 tmp[0] = tc->link.spread ? DP_SPREAD_AMP_0_5 : 0x00; 1168 /* MAIN_LINK_CHANNEL_CODING_SET */ 1169 tmp[1] = DP_SET_ANSI_8B10B; 1170 ret = drm_dp_dpcd_write(aux, DP_DOWNSPREAD_CTRL, tmp, 2); 1171 if (ret < 0) 1172 goto err_dpcd_write; 1173 1174 /* Reset voltage-swing & pre-emphasis */ 1175 tmp[0] = tmp[1] = DP_TRAIN_VOLTAGE_SWING_LEVEL_0 | 1176 DP_TRAIN_PRE_EMPH_LEVEL_0; 1177 ret = drm_dp_dpcd_write(aux, DP_TRAINING_LANE0_SET, tmp, 2); 1178 if (ret < 0) 1179 goto err_dpcd_write; 1180 1181 /* Clock-Recovery */ 1182 1183 /* Set DPCD 0x102 for Training Pattern 1 */ 1184 ret = regmap_write(tc->regmap, DP0_SNKLTCTRL, 1185 DP_LINK_SCRAMBLING_DISABLE | 1186 DP_TRAINING_PATTERN_1); 1187 if (ret) 1188 return ret; 1189 1190 ret = regmap_write(tc->regmap, DP0_LTLOOPCTRL, 1191 (15 << 28) | /* Defer Iteration Count */ 1192 (15 << 24) | /* Loop Iteration Count */ 1193 (0xd << 0)); /* Loop Timer Delay */ 1194 if (ret) 1195 return ret; 1196 1197 ret = regmap_write(tc->regmap, DP0_SRCCTRL, 1198 tc_srcctrl(tc) | DP0_SRCCTRL_SCRMBLDIS | 1199 DP0_SRCCTRL_AUTOCORRECT | 1200 DP0_SRCCTRL_TP1); 1201 if (ret) 1202 return ret; 1203 1204 /* Enable DP0 to start Link Training */ 1205 ret = regmap_write(tc->regmap, DP0CTL, 1206 (drm_dp_enhanced_frame_cap(tc->link.dpcd) ? 1207 EF_EN : 0) | DP_EN); 1208 if (ret) 1209 return ret; 1210 1211 /* wait */ 1212 1213 ret = tc_wait_link_training(tc); 1214 if (ret < 0) 1215 return ret; 1216 1217 if (ret) { 1218 dev_err(tc->dev, "Link training phase 1 failed: %s\n", 1219 training_pattern1_errors[ret]); 1220 return -ENODEV; 1221 } 1222 1223 /* Channel Equalization */ 1224 1225 /* Set DPCD 0x102 for Training Pattern 2 */ 1226 ret = regmap_write(tc->regmap, DP0_SNKLTCTRL, 1227 DP_LINK_SCRAMBLING_DISABLE | 1228 DP_TRAINING_PATTERN_2); 1229 if (ret) 1230 return ret; 1231 1232 ret = regmap_write(tc->regmap, DP0_SRCCTRL, 1233 tc_srcctrl(tc) | DP0_SRCCTRL_SCRMBLDIS | 1234 DP0_SRCCTRL_AUTOCORRECT | 1235 DP0_SRCCTRL_TP2); 1236 if (ret) 1237 return ret; 1238 1239 /* wait */ 1240 ret = tc_wait_link_training(tc); 1241 if (ret < 0) 1242 return ret; 1243 1244 if (ret) { 1245 dev_err(tc->dev, "Link training phase 2 failed: %s\n", 1246 training_pattern2_errors[ret]); 1247 return -ENODEV; 1248 } 1249 1250 /* 1251 * Toshiba's documentation suggests to first clear DPCD 0x102, then 1252 * clear the training pattern bit in DP0_SRCCTRL. Testing shows 1253 * that the link sometimes drops if those steps are done in that order, 1254 * but if the steps are done in reverse order, the link stays up. 1255 * 1256 * So we do the steps differently than documented here. 1257 */ 1258 1259 /* Clear Training Pattern, set AutoCorrect Mode = 1 */ 1260 ret = regmap_write(tc->regmap, DP0_SRCCTRL, tc_srcctrl(tc) | 1261 DP0_SRCCTRL_AUTOCORRECT); 1262 if (ret) 1263 return ret; 1264 1265 /* Clear DPCD 0x102 */ 1266 /* Note: Can Not use DP0_SNKLTCTRL (0x06E4) short cut */ 1267 tmp[0] = tc->link.scrambler_dis ? DP_LINK_SCRAMBLING_DISABLE : 0x00; 1268 ret = drm_dp_dpcd_writeb(aux, DP_TRAINING_PATTERN_SET, tmp[0]); 1269 if (ret < 0) 1270 goto err_dpcd_write; 1271 1272 /* Check link status */ 1273 ret = drm_dp_dpcd_read_link_status(aux, tmp); 1274 if (ret < 0) 1275 goto err_dpcd_read; 1276 1277 ret = 0; 1278 1279 value = tmp[0] & DP_CHANNEL_EQ_BITS; 1280 1281 if (value != DP_CHANNEL_EQ_BITS) { 1282 dev_err(tc->dev, "Lane 0 failed: %x\n", value); 1283 ret = -ENODEV; 1284 } 1285 1286 if (tc->link.num_lanes == 2) { 1287 value = (tmp[0] >> 4) & DP_CHANNEL_EQ_BITS; 1288 1289 if (value != DP_CHANNEL_EQ_BITS) { 1290 dev_err(tc->dev, "Lane 1 failed: %x\n", value); 1291 ret = -ENODEV; 1292 } 1293 1294 if (!(tmp[2] & DP_INTERLANE_ALIGN_DONE)) { 1295 dev_err(tc->dev, "Interlane align failed\n"); 1296 ret = -ENODEV; 1297 } 1298 } 1299 1300 if (ret) { 1301 dev_err(dev, "0x0202 LANE0_1_STATUS: 0x%02x\n", tmp[0]); 1302 dev_err(dev, "0x0203 LANE2_3_STATUS 0x%02x\n", tmp[1]); 1303 dev_err(dev, "0x0204 LANE_ALIGN_STATUS_UPDATED: 0x%02x\n", tmp[2]); 1304 dev_err(dev, "0x0205 SINK_STATUS: 0x%02x\n", tmp[3]); 1305 dev_err(dev, "0x0206 ADJUST_REQUEST_LANE0_1: 0x%02x\n", tmp[4]); 1306 dev_err(dev, "0x0207 ADJUST_REQUEST_LANE2_3: 0x%02x\n", tmp[5]); 1307 return ret; 1308 } 1309 1310 return 0; 1311 err_dpcd_read: 1312 dev_err(tc->dev, "Failed to read DPCD: %d\n", ret); 1313 return ret; 1314 err_dpcd_write: 1315 dev_err(tc->dev, "Failed to write DPCD: %d\n", ret); 1316 return ret; 1317 } 1318 1319 static int tc_main_link_disable(struct tc_data *tc) 1320 { 1321 int ret; 1322 1323 dev_dbg(tc->dev, "link disable\n"); 1324 1325 ret = regmap_write(tc->regmap, DP0_SRCCTRL, 0); 1326 if (ret) 1327 return ret; 1328 1329 ret = regmap_write(tc->regmap, DP0CTL, 0); 1330 if (ret) 1331 return ret; 1332 1333 return regmap_update_bits(tc->regmap, DP_PHY_CTRL, 1334 PHY_M0_RST | PHY_M1_RST | PHY_M0_EN, 1335 PHY_M0_RST | PHY_M1_RST); 1336 } 1337 1338 static int tc_dsi_rx_enable(struct tc_data *tc) 1339 { 1340 u32 value; 1341 int ret; 1342 1343 regmap_write(tc->regmap, PPI_D0S_CLRSIPOCOUNT, 25); 1344 regmap_write(tc->regmap, PPI_D1S_CLRSIPOCOUNT, 25); 1345 regmap_write(tc->regmap, PPI_D2S_CLRSIPOCOUNT, 25); 1346 regmap_write(tc->regmap, PPI_D3S_CLRSIPOCOUNT, 25); 1347 regmap_write(tc->regmap, PPI_D0S_ATMR, 0); 1348 regmap_write(tc->regmap, PPI_D1S_ATMR, 0); 1349 regmap_write(tc->regmap, PPI_TX_RX_TA, TTA_GET | TTA_SURE); 1350 regmap_write(tc->regmap, PPI_LPTXTIMECNT, LPX_PERIOD); 1351 1352 value = ((LANEENABLE_L0EN << tc->dsi->lanes) - LANEENABLE_L0EN) | 1353 LANEENABLE_CLEN; 1354 regmap_write(tc->regmap, PPI_LANEENABLE, value); 1355 regmap_write(tc->regmap, DSI_LANEENABLE, value); 1356 1357 /* Set input interface */ 1358 value = DP0_AUDSRC_NO_INPUT; 1359 if (tc_test_pattern) 1360 value |= DP0_VIDSRC_COLOR_BAR; 1361 else 1362 value |= DP0_VIDSRC_DSI_RX; 1363 ret = regmap_write(tc->regmap, SYSCTRL, value); 1364 if (ret) 1365 return ret; 1366 1367 usleep_range(120, 150); 1368 1369 regmap_write(tc->regmap, PPI_STARTPPI, PPI_START_FUNCTION); 1370 regmap_write(tc->regmap, DSI_STARTDSI, DSI_RX_START); 1371 1372 return 0; 1373 } 1374 1375 static int tc_dpi_rx_enable(struct tc_data *tc) 1376 { 1377 u32 value; 1378 1379 /* Set input interface */ 1380 value = DP0_AUDSRC_NO_INPUT; 1381 if (tc_test_pattern) 1382 value |= DP0_VIDSRC_COLOR_BAR; 1383 else 1384 value |= DP0_VIDSRC_DPI_RX; 1385 return regmap_write(tc->regmap, SYSCTRL, value); 1386 } 1387 1388 static int tc_dpi_stream_enable(struct tc_data *tc) 1389 { 1390 int ret; 1391 1392 dev_dbg(tc->dev, "enable video stream\n"); 1393 1394 /* Setup PLL */ 1395 ret = tc_set_syspllparam(tc); 1396 if (ret) 1397 return ret; 1398 1399 /* 1400 * Initially PLLs are in bypass. Force PLL parameter update, 1401 * disable PLL bypass, enable PLL 1402 */ 1403 ret = tc_pllupdate(tc, DP0_PLLCTRL); 1404 if (ret) 1405 return ret; 1406 1407 ret = tc_pllupdate(tc, DP1_PLLCTRL); 1408 if (ret) 1409 return ret; 1410 1411 /* Pixel PLL must always be enabled for DPI mode */ 1412 ret = tc_pxl_pll_en(tc, clk_get_rate(tc->refclk), 1413 1000 * tc->mode.clock); 1414 if (ret) 1415 return ret; 1416 1417 ret = tc_set_common_video_mode(tc, &tc->mode); 1418 if (ret) 1419 return ret; 1420 1421 ret = tc_set_dpi_video_mode(tc, &tc->mode); 1422 if (ret) 1423 return ret; 1424 1425 return tc_dsi_rx_enable(tc); 1426 } 1427 1428 static int tc_dpi_stream_disable(struct tc_data *tc) 1429 { 1430 dev_dbg(tc->dev, "disable video stream\n"); 1431 1432 tc_pxl_pll_dis(tc); 1433 1434 return 0; 1435 } 1436 1437 static int tc_edp_stream_enable(struct tc_data *tc) 1438 { 1439 int ret; 1440 u32 value; 1441 1442 dev_dbg(tc->dev, "enable video stream\n"); 1443 1444 /* 1445 * Pixel PLL must be enabled for DSI input mode and test pattern. 1446 * 1447 * Per TC9595XBG datasheet Revision 0.1 2018-12-27 Figure 4.18 1448 * "Clock Mode Selection and Clock Sources", either Pixel PLL 1449 * or DPI_PCLK supplies StrmClk. DPI_PCLK is only available in 1450 * case valid Pixel Clock are supplied to the chip DPI input. 1451 * In case built-in test pattern is desired OR DSI input mode 1452 * is used, DPI_PCLK is not available and thus Pixel PLL must 1453 * be used instead. 1454 */ 1455 if (tc->input_connector_dsi || tc_test_pattern) { 1456 ret = tc_pxl_pll_en(tc, clk_get_rate(tc->refclk), 1457 1000 * tc->mode.clock); 1458 if (ret) 1459 return ret; 1460 } 1461 1462 ret = tc_set_common_video_mode(tc, &tc->mode); 1463 if (ret) 1464 return ret; 1465 1466 ret = tc_set_edp_video_mode(tc, &tc->mode); 1467 if (ret) 1468 return ret; 1469 1470 /* Set M/N */ 1471 ret = tc_stream_clock_calc(tc); 1472 if (ret) 1473 return ret; 1474 1475 value = VID_MN_GEN | DP_EN; 1476 if (drm_dp_enhanced_frame_cap(tc->link.dpcd)) 1477 value |= EF_EN; 1478 ret = regmap_write(tc->regmap, DP0CTL, value); 1479 if (ret) 1480 return ret; 1481 /* 1482 * VID_EN assertion should be delayed by at least N * LSCLK 1483 * cycles from the time VID_MN_GEN is enabled in order to 1484 * generate stable values for VID_M. LSCLK is 270 MHz or 1485 * 162 MHz, VID_N is set to 32768 in tc_stream_clock_calc(), 1486 * so a delay of at least 203 us should suffice. 1487 */ 1488 usleep_range(500, 1000); 1489 value |= VID_EN; 1490 ret = regmap_write(tc->regmap, DP0CTL, value); 1491 if (ret) 1492 return ret; 1493 1494 /* Set input interface */ 1495 if (tc->input_connector_dsi) 1496 return tc_dsi_rx_enable(tc); 1497 else 1498 return tc_dpi_rx_enable(tc); 1499 } 1500 1501 static int tc_edp_stream_disable(struct tc_data *tc) 1502 { 1503 int ret; 1504 1505 dev_dbg(tc->dev, "disable video stream\n"); 1506 1507 ret = regmap_update_bits(tc->regmap, DP0CTL, VID_EN, 0); 1508 if (ret) 1509 return ret; 1510 1511 tc_pxl_pll_dis(tc); 1512 1513 return 0; 1514 } 1515 1516 static void 1517 tc_dpi_bridge_atomic_enable(struct drm_bridge *bridge, 1518 struct drm_bridge_state *old_bridge_state) 1519 1520 { 1521 struct tc_data *tc = bridge_to_tc(bridge); 1522 int ret; 1523 1524 ret = tc_dpi_stream_enable(tc); 1525 if (ret < 0) { 1526 dev_err(tc->dev, "main link stream start error: %d\n", ret); 1527 tc_main_link_disable(tc); 1528 return; 1529 } 1530 } 1531 1532 static void 1533 tc_dpi_bridge_atomic_disable(struct drm_bridge *bridge, 1534 struct drm_bridge_state *old_bridge_state) 1535 { 1536 struct tc_data *tc = bridge_to_tc(bridge); 1537 int ret; 1538 1539 ret = tc_dpi_stream_disable(tc); 1540 if (ret < 0) 1541 dev_err(tc->dev, "main link stream stop error: %d\n", ret); 1542 } 1543 1544 static void 1545 tc_edp_bridge_atomic_enable(struct drm_bridge *bridge, 1546 struct drm_bridge_state *old_bridge_state) 1547 { 1548 struct tc_data *tc = bridge_to_tc(bridge); 1549 int ret; 1550 1551 ret = tc_get_display_props(tc); 1552 if (ret < 0) { 1553 dev_err(tc->dev, "failed to read display props: %d\n", ret); 1554 return; 1555 } 1556 1557 ret = tc_main_link_enable(tc); 1558 if (ret < 0) { 1559 dev_err(tc->dev, "main link enable error: %d\n", ret); 1560 return; 1561 } 1562 1563 ret = tc_edp_stream_enable(tc); 1564 if (ret < 0) { 1565 dev_err(tc->dev, "main link stream start error: %d\n", ret); 1566 tc_main_link_disable(tc); 1567 return; 1568 } 1569 } 1570 1571 static void 1572 tc_edp_bridge_atomic_disable(struct drm_bridge *bridge, 1573 struct drm_bridge_state *old_bridge_state) 1574 { 1575 struct tc_data *tc = bridge_to_tc(bridge); 1576 int ret; 1577 1578 ret = tc_edp_stream_disable(tc); 1579 if (ret < 0) 1580 dev_err(tc->dev, "main link stream stop error: %d\n", ret); 1581 1582 ret = tc_main_link_disable(tc); 1583 if (ret < 0) 1584 dev_err(tc->dev, "main link disable error: %d\n", ret); 1585 } 1586 1587 static int tc_dpi_atomic_check(struct drm_bridge *bridge, 1588 struct drm_bridge_state *bridge_state, 1589 struct drm_crtc_state *crtc_state, 1590 struct drm_connector_state *conn_state) 1591 { 1592 /* DSI->DPI interface clock limitation: upto 100 MHz */ 1593 if (crtc_state->adjusted_mode.clock > 100000) 1594 return -EINVAL; 1595 1596 return 0; 1597 } 1598 1599 static int tc_edp_atomic_check(struct drm_bridge *bridge, 1600 struct drm_bridge_state *bridge_state, 1601 struct drm_crtc_state *crtc_state, 1602 struct drm_connector_state *conn_state) 1603 { 1604 /* DPI->(e)DP interface clock limitation: upto 154 MHz */ 1605 if (crtc_state->adjusted_mode.clock > 154000) 1606 return -EINVAL; 1607 1608 return 0; 1609 } 1610 1611 static enum drm_mode_status 1612 tc_dpi_mode_valid(struct drm_bridge *bridge, 1613 const struct drm_display_info *info, 1614 const struct drm_display_mode *mode) 1615 { 1616 /* DPI interface clock limitation: upto 100 MHz */ 1617 if (mode->clock > 100000) 1618 return MODE_CLOCK_HIGH; 1619 1620 return MODE_OK; 1621 } 1622 1623 static enum drm_mode_status 1624 tc_edp_mode_valid(struct drm_bridge *bridge, 1625 const struct drm_display_info *info, 1626 const struct drm_display_mode *mode) 1627 { 1628 struct tc_data *tc = bridge_to_tc(bridge); 1629 u32 req, avail; 1630 u32 bits_per_pixel = 24; 1631 1632 /* DPI interface clock limitation: upto 154 MHz */ 1633 if (mode->clock > 154000) 1634 return MODE_CLOCK_HIGH; 1635 1636 req = mode->clock * bits_per_pixel / 8; 1637 avail = tc->link.num_lanes * tc->link.rate; 1638 1639 if (req > avail) 1640 return MODE_BAD; 1641 1642 return MODE_OK; 1643 } 1644 1645 static void tc_bridge_mode_set(struct drm_bridge *bridge, 1646 const struct drm_display_mode *mode, 1647 const struct drm_display_mode *adj) 1648 { 1649 struct tc_data *tc = bridge_to_tc(bridge); 1650 1651 drm_mode_copy(&tc->mode, mode); 1652 } 1653 1654 static const struct drm_edid *tc_edid_read(struct drm_bridge *bridge, 1655 struct drm_connector *connector) 1656 { 1657 struct tc_data *tc = bridge_to_tc(bridge); 1658 1659 return drm_edid_read_ddc(connector, &tc->aux.ddc); 1660 } 1661 1662 static int tc_connector_get_modes(struct drm_connector *connector) 1663 { 1664 struct tc_data *tc = connector_to_tc(connector); 1665 int num_modes; 1666 const struct drm_edid *drm_edid; 1667 int ret; 1668 1669 ret = tc_get_display_props(tc); 1670 if (ret < 0) { 1671 dev_err(tc->dev, "failed to read display props: %d\n", ret); 1672 return 0; 1673 } 1674 1675 if (tc->panel_bridge) { 1676 num_modes = drm_bridge_get_modes(tc->panel_bridge, connector); 1677 if (num_modes > 0) 1678 return num_modes; 1679 } 1680 1681 drm_edid = tc_edid_read(&tc->bridge, connector); 1682 drm_edid_connector_update(connector, drm_edid); 1683 num_modes = drm_edid_connector_add_modes(connector); 1684 drm_edid_free(drm_edid); 1685 1686 return num_modes; 1687 } 1688 1689 static const struct drm_connector_helper_funcs tc_connector_helper_funcs = { 1690 .get_modes = tc_connector_get_modes, 1691 }; 1692 1693 static enum drm_connector_status tc_bridge_detect(struct drm_bridge *bridge) 1694 { 1695 struct tc_data *tc = bridge_to_tc(bridge); 1696 bool conn; 1697 u32 val; 1698 int ret; 1699 1700 ret = regmap_read(tc->regmap, GPIOI, &val); 1701 if (ret) 1702 return connector_status_unknown; 1703 1704 conn = val & BIT(tc->hpd_pin); 1705 1706 if (conn) 1707 return connector_status_connected; 1708 else 1709 return connector_status_disconnected; 1710 } 1711 1712 static enum drm_connector_status 1713 tc_connector_detect(struct drm_connector *connector, bool force) 1714 { 1715 struct tc_data *tc = connector_to_tc(connector); 1716 1717 if (tc->hpd_pin >= 0) 1718 return tc_bridge_detect(&tc->bridge); 1719 1720 if (tc->panel_bridge) 1721 return connector_status_connected; 1722 else 1723 return connector_status_unknown; 1724 } 1725 1726 static const struct drm_connector_funcs tc_connector_funcs = { 1727 .detect = tc_connector_detect, 1728 .fill_modes = drm_helper_probe_single_connector_modes, 1729 .destroy = drm_connector_cleanup, 1730 .reset = drm_atomic_helper_connector_reset, 1731 .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, 1732 .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, 1733 }; 1734 1735 static int tc_dpi_bridge_attach(struct drm_bridge *bridge, 1736 enum drm_bridge_attach_flags flags) 1737 { 1738 struct tc_data *tc = bridge_to_tc(bridge); 1739 1740 if (!tc->panel_bridge) 1741 return 0; 1742 1743 return drm_bridge_attach(tc->bridge.encoder, tc->panel_bridge, 1744 &tc->bridge, flags); 1745 } 1746 1747 static int tc_edp_bridge_attach(struct drm_bridge *bridge, 1748 enum drm_bridge_attach_flags flags) 1749 { 1750 u32 bus_format = MEDIA_BUS_FMT_RGB888_1X24; 1751 struct tc_data *tc = bridge_to_tc(bridge); 1752 struct drm_device *drm = bridge->dev; 1753 int ret; 1754 1755 if (tc->panel_bridge) { 1756 /* If a connector is required then this driver shall create it */ 1757 ret = drm_bridge_attach(tc->bridge.encoder, tc->panel_bridge, 1758 &tc->bridge, flags | DRM_BRIDGE_ATTACH_NO_CONNECTOR); 1759 if (ret) 1760 return ret; 1761 } 1762 1763 if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) 1764 return 0; 1765 1766 tc->aux.drm_dev = drm; 1767 ret = drm_dp_aux_register(&tc->aux); 1768 if (ret < 0) 1769 return ret; 1770 1771 /* Create DP/eDP connector */ 1772 drm_connector_helper_add(&tc->connector, &tc_connector_helper_funcs); 1773 ret = drm_connector_init(drm, &tc->connector, &tc_connector_funcs, tc->bridge.type); 1774 if (ret) 1775 goto aux_unregister; 1776 1777 /* Don't poll if don't have HPD connected */ 1778 if (tc->hpd_pin >= 0) { 1779 if (tc->have_irq) 1780 tc->connector.polled = DRM_CONNECTOR_POLL_HPD; 1781 else 1782 tc->connector.polled = DRM_CONNECTOR_POLL_CONNECT | 1783 DRM_CONNECTOR_POLL_DISCONNECT; 1784 } 1785 1786 drm_display_info_set_bus_formats(&tc->connector.display_info, 1787 &bus_format, 1); 1788 tc->connector.display_info.bus_flags = 1789 DRM_BUS_FLAG_DE_HIGH | 1790 DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE | 1791 DRM_BUS_FLAG_SYNC_DRIVE_NEGEDGE; 1792 drm_connector_attach_encoder(&tc->connector, tc->bridge.encoder); 1793 1794 return 0; 1795 aux_unregister: 1796 drm_dp_aux_unregister(&tc->aux); 1797 return ret; 1798 } 1799 1800 static void tc_edp_bridge_detach(struct drm_bridge *bridge) 1801 { 1802 drm_dp_aux_unregister(&bridge_to_tc(bridge)->aux); 1803 } 1804 1805 #define MAX_INPUT_SEL_FORMATS 1 1806 1807 static u32 * 1808 tc_dpi_atomic_get_input_bus_fmts(struct drm_bridge *bridge, 1809 struct drm_bridge_state *bridge_state, 1810 struct drm_crtc_state *crtc_state, 1811 struct drm_connector_state *conn_state, 1812 u32 output_fmt, 1813 unsigned int *num_input_fmts) 1814 { 1815 u32 *input_fmts; 1816 1817 *num_input_fmts = 0; 1818 1819 input_fmts = kcalloc(MAX_INPUT_SEL_FORMATS, sizeof(*input_fmts), 1820 GFP_KERNEL); 1821 if (!input_fmts) 1822 return NULL; 1823 1824 /* This is the DSI-end bus format */ 1825 input_fmts[0] = MEDIA_BUS_FMT_RGB888_1X24; 1826 *num_input_fmts = 1; 1827 1828 return input_fmts; 1829 } 1830 1831 static const struct drm_bridge_funcs tc_dpi_bridge_funcs = { 1832 .attach = tc_dpi_bridge_attach, 1833 .mode_valid = tc_dpi_mode_valid, 1834 .mode_set = tc_bridge_mode_set, 1835 .atomic_check = tc_dpi_atomic_check, 1836 .atomic_enable = tc_dpi_bridge_atomic_enable, 1837 .atomic_disable = tc_dpi_bridge_atomic_disable, 1838 .atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state, 1839 .atomic_destroy_state = drm_atomic_helper_bridge_destroy_state, 1840 .atomic_reset = drm_atomic_helper_bridge_reset, 1841 .atomic_get_input_bus_fmts = tc_dpi_atomic_get_input_bus_fmts, 1842 }; 1843 1844 static const struct drm_bridge_funcs tc_edp_bridge_funcs = { 1845 .attach = tc_edp_bridge_attach, 1846 .detach = tc_edp_bridge_detach, 1847 .mode_valid = tc_edp_mode_valid, 1848 .mode_set = tc_bridge_mode_set, 1849 .atomic_check = tc_edp_atomic_check, 1850 .atomic_enable = tc_edp_bridge_atomic_enable, 1851 .atomic_disable = tc_edp_bridge_atomic_disable, 1852 .detect = tc_bridge_detect, 1853 .edid_read = tc_edid_read, 1854 .atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state, 1855 .atomic_destroy_state = drm_atomic_helper_bridge_destroy_state, 1856 .atomic_reset = drm_atomic_helper_bridge_reset, 1857 }; 1858 1859 static bool tc_readable_reg(struct device *dev, unsigned int reg) 1860 { 1861 switch (reg) { 1862 /* DSI D-PHY Layer */ 1863 case 0x004: 1864 case 0x020: 1865 case 0x024: 1866 case 0x028: 1867 case 0x02c: 1868 case 0x030: 1869 case 0x038: 1870 case 0x040: 1871 case 0x044: 1872 case 0x048: 1873 case 0x04c: 1874 case 0x050: 1875 case 0x054: 1876 /* DSI PPI Layer */ 1877 case PPI_STARTPPI: 1878 case 0x108: 1879 case 0x110: 1880 case PPI_LPTXTIMECNT: 1881 case PPI_LANEENABLE: 1882 case PPI_TX_RX_TA: 1883 case 0x140: 1884 case PPI_D0S_ATMR: 1885 case PPI_D1S_ATMR: 1886 case 0x14c: 1887 case 0x150: 1888 case PPI_D0S_CLRSIPOCOUNT: 1889 case PPI_D1S_CLRSIPOCOUNT: 1890 case PPI_D2S_CLRSIPOCOUNT: 1891 case PPI_D3S_CLRSIPOCOUNT: 1892 case 0x180: 1893 case 0x184: 1894 case 0x188: 1895 case 0x18c: 1896 case 0x190: 1897 case 0x1a0: 1898 case 0x1a4: 1899 case 0x1a8: 1900 case 0x1ac: 1901 case 0x1b0: 1902 case 0x1c0: 1903 case 0x1c4: 1904 case 0x1c8: 1905 case 0x1cc: 1906 case 0x1d0: 1907 case 0x1e0: 1908 case 0x1e4: 1909 case 0x1f0: 1910 case 0x1f4: 1911 /* DSI Protocol Layer */ 1912 case DSI_STARTDSI: 1913 case DSI_BUSYDSI: 1914 case DSI_LANEENABLE: 1915 case DSI_LANESTATUS0: 1916 case DSI_LANESTATUS1: 1917 case DSI_INTSTATUS: 1918 case 0x224: 1919 case 0x228: 1920 case 0x230: 1921 /* DSI General */ 1922 case DSIERRCNT: 1923 /* DSI Application Layer */ 1924 case 0x400: 1925 case 0x404: 1926 /* DPI */ 1927 case DPIPXLFMT: 1928 /* Parallel Output */ 1929 case POCTRL: 1930 /* Video Path0 Configuration */ 1931 case VPCTRL0: 1932 case HTIM01: 1933 case HTIM02: 1934 case VTIM01: 1935 case VTIM02: 1936 case VFUEN0: 1937 /* System */ 1938 case TC_IDREG: 1939 case 0x504: 1940 case SYSSTAT: 1941 case SYSRSTENB: 1942 case SYSCTRL: 1943 /* I2C */ 1944 case 0x520: 1945 /* GPIO */ 1946 case GPIOM: 1947 case GPIOC: 1948 case GPIOO: 1949 case GPIOI: 1950 /* Interrupt */ 1951 case INTCTL_G: 1952 case INTSTS_G: 1953 case 0x570: 1954 case 0x574: 1955 case INT_GP0_LCNT: 1956 case INT_GP1_LCNT: 1957 /* DisplayPort Control */ 1958 case DP0CTL: 1959 /* DisplayPort Clock */ 1960 case DP0_VIDMNGEN0: 1961 case DP0_VIDMNGEN1: 1962 case DP0_VMNGENSTATUS: 1963 case 0x628: 1964 case 0x62c: 1965 case 0x630: 1966 /* DisplayPort Main Channel */ 1967 case DP0_SECSAMPLE: 1968 case DP0_VIDSYNCDELAY: 1969 case DP0_TOTALVAL: 1970 case DP0_STARTVAL: 1971 case DP0_ACTIVEVAL: 1972 case DP0_SYNCVAL: 1973 case DP0_MISC: 1974 /* DisplayPort Aux Channel */ 1975 case DP0_AUXCFG0: 1976 case DP0_AUXCFG1: 1977 case DP0_AUXADDR: 1978 case 0x66c: 1979 case 0x670: 1980 case 0x674: 1981 case 0x678: 1982 case 0x67c: 1983 case 0x680: 1984 case 0x684: 1985 case 0x688: 1986 case DP0_AUXSTATUS: 1987 case DP0_AUXI2CADR: 1988 /* DisplayPort Link Training */ 1989 case DP0_SRCCTRL: 1990 case DP0_LTSTAT: 1991 case DP0_SNKLTCHGREQ: 1992 case DP0_LTLOOPCTRL: 1993 case DP0_SNKLTCTRL: 1994 case 0x6e8: 1995 case 0x6ec: 1996 case 0x6f0: 1997 case 0x6f4: 1998 /* DisplayPort Audio */ 1999 case 0x700: 2000 case 0x704: 2001 case 0x708: 2002 case 0x70c: 2003 case 0x710: 2004 case 0x714: 2005 case 0x718: 2006 case 0x71c: 2007 case 0x720: 2008 /* DisplayPort Source Control */ 2009 case DP1_SRCCTRL: 2010 /* DisplayPort PHY */ 2011 case DP_PHY_CTRL: 2012 case 0x810: 2013 case 0x814: 2014 case 0x820: 2015 case 0x840: 2016 /* I2S */ 2017 case 0x880: 2018 case 0x888: 2019 case 0x88c: 2020 case 0x890: 2021 case 0x894: 2022 case 0x898: 2023 case 0x89c: 2024 case 0x8a0: 2025 case 0x8a4: 2026 case 0x8a8: 2027 case 0x8ac: 2028 case 0x8b0: 2029 case 0x8b4: 2030 /* PLL */ 2031 case DP0_PLLCTRL: 2032 case DP1_PLLCTRL: 2033 case PXL_PLLCTRL: 2034 case PXL_PLLPARAM: 2035 case SYS_PLLPARAM: 2036 /* HDCP */ 2037 case 0x980: 2038 case 0x984: 2039 case 0x988: 2040 case 0x98c: 2041 case 0x990: 2042 case 0x994: 2043 case 0x998: 2044 case 0x99c: 2045 case 0x9a0: 2046 case 0x9a4: 2047 case 0x9a8: 2048 case 0x9ac: 2049 /* Debug */ 2050 case TSTCTL: 2051 case PLL_DBG: 2052 return true; 2053 } 2054 return false; 2055 } 2056 2057 static const struct regmap_range tc_volatile_ranges[] = { 2058 regmap_reg_range(PPI_BUSYPPI, PPI_BUSYPPI), 2059 regmap_reg_range(DSI_BUSYDSI, DSI_BUSYDSI), 2060 regmap_reg_range(DSI_LANESTATUS0, DSI_INTSTATUS), 2061 regmap_reg_range(DSIERRCNT, DSIERRCNT), 2062 regmap_reg_range(VFUEN0, VFUEN0), 2063 regmap_reg_range(SYSSTAT, SYSSTAT), 2064 regmap_reg_range(GPIOI, GPIOI), 2065 regmap_reg_range(INTSTS_G, INTSTS_G), 2066 regmap_reg_range(DP0_VMNGENSTATUS, DP0_VMNGENSTATUS), 2067 regmap_reg_range(DP0_AMNGENSTATUS, DP0_AMNGENSTATUS), 2068 regmap_reg_range(DP0_AUXWDATA(0), DP0_AUXSTATUS), 2069 regmap_reg_range(DP0_LTSTAT, DP0_SNKLTCHGREQ), 2070 regmap_reg_range(DP_PHY_CTRL, DP_PHY_CTRL), 2071 regmap_reg_range(DP0_PLLCTRL, PXL_PLLCTRL), 2072 }; 2073 2074 static const struct regmap_access_table tc_volatile_table = { 2075 .yes_ranges = tc_volatile_ranges, 2076 .n_yes_ranges = ARRAY_SIZE(tc_volatile_ranges), 2077 }; 2078 2079 static const struct regmap_range tc_precious_ranges[] = { 2080 regmap_reg_range(SYSSTAT, SYSSTAT), 2081 }; 2082 2083 static const struct regmap_access_table tc_precious_table = { 2084 .yes_ranges = tc_precious_ranges, 2085 .n_yes_ranges = ARRAY_SIZE(tc_precious_ranges), 2086 }; 2087 2088 static const struct regmap_range tc_non_writeable_ranges[] = { 2089 regmap_reg_range(PPI_BUSYPPI, PPI_BUSYPPI), 2090 regmap_reg_range(DSI_BUSYDSI, DSI_BUSYDSI), 2091 regmap_reg_range(DSI_LANESTATUS0, DSI_INTSTATUS), 2092 regmap_reg_range(TC_IDREG, SYSSTAT), 2093 regmap_reg_range(GPIOI, GPIOI), 2094 regmap_reg_range(DP0_LTSTAT, DP0_SNKLTCHGREQ), 2095 }; 2096 2097 static const struct regmap_access_table tc_writeable_table = { 2098 .no_ranges = tc_non_writeable_ranges, 2099 .n_no_ranges = ARRAY_SIZE(tc_non_writeable_ranges), 2100 }; 2101 2102 static const struct regmap_config tc_regmap_config = { 2103 .name = "tc358767", 2104 .reg_bits = 16, 2105 .val_bits = 32, 2106 .reg_stride = 4, 2107 .max_register = PLL_DBG, 2108 .cache_type = REGCACHE_MAPLE, 2109 .readable_reg = tc_readable_reg, 2110 .volatile_table = &tc_volatile_table, 2111 .precious_table = &tc_precious_table, 2112 .wr_table = &tc_writeable_table, 2113 .reg_format_endian = REGMAP_ENDIAN_BIG, 2114 .val_format_endian = REGMAP_ENDIAN_LITTLE, 2115 }; 2116 2117 static irqreturn_t tc_irq_handler(int irq, void *arg) 2118 { 2119 struct tc_data *tc = arg; 2120 u32 val; 2121 int r; 2122 2123 r = regmap_read(tc->regmap, INTSTS_G, &val); 2124 if (r) 2125 return IRQ_NONE; 2126 2127 if (!val) 2128 return IRQ_NONE; 2129 2130 if (val & INT_SYSERR) { 2131 u32 stat = 0; 2132 2133 regmap_read(tc->regmap, SYSSTAT, &stat); 2134 2135 dev_err(tc->dev, "syserr %x\n", stat); 2136 } 2137 2138 if (tc->hpd_pin >= 0 && tc->bridge.dev) { 2139 /* 2140 * H is triggered when the GPIO goes high. 2141 * 2142 * LC is triggered when the GPIO goes low and stays low for 2143 * the duration of LCNT 2144 */ 2145 bool h = val & INT_GPIO_H(tc->hpd_pin); 2146 bool lc = val & INT_GPIO_LC(tc->hpd_pin); 2147 2148 dev_dbg(tc->dev, "GPIO%d: %s %s\n", tc->hpd_pin, 2149 h ? "H" : "", lc ? "LC" : ""); 2150 2151 if (h || lc) 2152 drm_kms_helper_hotplug_event(tc->bridge.dev); 2153 } 2154 2155 regmap_write(tc->regmap, INTSTS_G, val); 2156 2157 return IRQ_HANDLED; 2158 } 2159 2160 static int tc_mipi_dsi_host_attach(struct tc_data *tc) 2161 { 2162 struct device *dev = tc->dev; 2163 struct device_node *host_node; 2164 struct device_node *endpoint; 2165 struct mipi_dsi_device *dsi; 2166 struct mipi_dsi_host *host; 2167 const struct mipi_dsi_device_info info = { 2168 .type = "tc358767", 2169 .channel = 0, 2170 .node = NULL, 2171 }; 2172 int dsi_lanes, ret; 2173 2174 endpoint = of_graph_get_endpoint_by_regs(dev->of_node, 0, -1); 2175 dsi_lanes = drm_of_get_data_lanes_count(endpoint, 1, 4); 2176 host_node = of_graph_get_remote_port_parent(endpoint); 2177 host = of_find_mipi_dsi_host_by_node(host_node); 2178 of_node_put(host_node); 2179 of_node_put(endpoint); 2180 2181 if (!host) 2182 return -EPROBE_DEFER; 2183 2184 if (dsi_lanes < 0) 2185 return dsi_lanes; 2186 2187 dsi = devm_mipi_dsi_device_register_full(dev, host, &info); 2188 if (IS_ERR(dsi)) 2189 return dev_err_probe(dev, PTR_ERR(dsi), 2190 "failed to create dsi device\n"); 2191 2192 tc->dsi = dsi; 2193 dsi->lanes = dsi_lanes; 2194 dsi->format = MIPI_DSI_FMT_RGB888; 2195 dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST | 2196 MIPI_DSI_MODE_LPM | MIPI_DSI_CLOCK_NON_CONTINUOUS; 2197 2198 ret = devm_mipi_dsi_attach(dev, dsi); 2199 if (ret < 0) { 2200 dev_err(dev, "failed to attach dsi to host: %d\n", ret); 2201 return ret; 2202 } 2203 2204 return 0; 2205 } 2206 2207 static int tc_probe_dpi_bridge_endpoint(struct tc_data *tc) 2208 { 2209 struct device *dev = tc->dev; 2210 struct drm_bridge *bridge; 2211 struct drm_panel *panel; 2212 int ret; 2213 2214 /* port@1 is the DPI input/output port */ 2215 ret = drm_of_find_panel_or_bridge(dev->of_node, 1, 0, &panel, &bridge); 2216 if (ret && ret != -ENODEV) 2217 return ret; 2218 2219 if (panel) { 2220 bridge = devm_drm_panel_bridge_add(dev, panel); 2221 if (IS_ERR(bridge)) 2222 return PTR_ERR(bridge); 2223 } 2224 2225 if (bridge) { 2226 tc->panel_bridge = bridge; 2227 tc->bridge.type = DRM_MODE_CONNECTOR_DPI; 2228 tc->bridge.funcs = &tc_dpi_bridge_funcs; 2229 2230 return 0; 2231 } 2232 2233 return ret; 2234 } 2235 2236 static int tc_probe_edp_bridge_endpoint(struct tc_data *tc) 2237 { 2238 struct device *dev = tc->dev; 2239 struct drm_panel *panel; 2240 int ret; 2241 2242 /* port@2 is the output port */ 2243 ret = drm_of_find_panel_or_bridge(dev->of_node, 2, 0, &panel, NULL); 2244 if (ret && ret != -ENODEV) 2245 return ret; 2246 2247 if (panel) { 2248 struct drm_bridge *panel_bridge; 2249 2250 panel_bridge = devm_drm_panel_bridge_add(dev, panel); 2251 if (IS_ERR(panel_bridge)) 2252 return PTR_ERR(panel_bridge); 2253 2254 tc->panel_bridge = panel_bridge; 2255 tc->bridge.type = DRM_MODE_CONNECTOR_eDP; 2256 } else { 2257 tc->bridge.type = DRM_MODE_CONNECTOR_DisplayPort; 2258 } 2259 2260 tc->bridge.funcs = &tc_edp_bridge_funcs; 2261 if (tc->hpd_pin >= 0) 2262 tc->bridge.ops |= DRM_BRIDGE_OP_DETECT; 2263 tc->bridge.ops |= DRM_BRIDGE_OP_EDID; 2264 2265 return 0; 2266 } 2267 2268 static int tc_probe_bridge_endpoint(struct tc_data *tc) 2269 { 2270 struct device *dev = tc->dev; 2271 struct of_endpoint endpoint; 2272 struct device_node *node = NULL; 2273 const u8 mode_dpi_to_edp = BIT(1) | BIT(2); 2274 const u8 mode_dpi_to_dp = BIT(1); 2275 const u8 mode_dsi_to_edp = BIT(0) | BIT(2); 2276 const u8 mode_dsi_to_dp = BIT(0); 2277 const u8 mode_dsi_to_dpi = BIT(0) | BIT(1); 2278 u8 mode = 0; 2279 2280 /* 2281 * Determine bridge configuration. 2282 * 2283 * Port allocation: 2284 * port@0 - DSI input 2285 * port@1 - DPI input/output 2286 * port@2 - eDP output 2287 * 2288 * Possible connections: 2289 * DPI -> port@1 -> port@2 -> eDP :: [port@0 is not connected] 2290 * DSI -> port@0 -> port@2 -> eDP :: [port@1 is not connected] 2291 * DSI -> port@0 -> port@1 -> DPI :: [port@2 is not connected] 2292 */ 2293 2294 for_each_endpoint_of_node(dev->of_node, node) { 2295 of_graph_parse_endpoint(node, &endpoint); 2296 if (endpoint.port > 2) { 2297 of_node_put(node); 2298 return -EINVAL; 2299 } 2300 mode |= BIT(endpoint.port); 2301 } 2302 2303 if (mode == mode_dpi_to_edp || mode == mode_dpi_to_dp) { 2304 tc->input_connector_dsi = false; 2305 return tc_probe_edp_bridge_endpoint(tc); 2306 } else if (mode == mode_dsi_to_dpi) { 2307 tc->input_connector_dsi = true; 2308 return tc_probe_dpi_bridge_endpoint(tc); 2309 } else if (mode == mode_dsi_to_edp || mode == mode_dsi_to_dp) { 2310 tc->input_connector_dsi = true; 2311 return tc_probe_edp_bridge_endpoint(tc); 2312 } 2313 2314 dev_warn(dev, "Invalid mode (0x%x) is not supported!\n", mode); 2315 2316 return -EINVAL; 2317 } 2318 2319 static int tc_probe(struct i2c_client *client) 2320 { 2321 struct device *dev = &client->dev; 2322 struct tc_data *tc; 2323 int ret; 2324 2325 tc = devm_kzalloc(dev, sizeof(*tc), GFP_KERNEL); 2326 if (!tc) 2327 return -ENOMEM; 2328 2329 tc->dev = dev; 2330 2331 ret = tc_probe_bridge_endpoint(tc); 2332 if (ret) 2333 return ret; 2334 2335 tc->refclk = devm_clk_get_enabled(dev, "ref"); 2336 if (IS_ERR(tc->refclk)) 2337 return dev_err_probe(dev, PTR_ERR(tc->refclk), 2338 "Failed to get and enable the ref clk\n"); 2339 2340 /* tRSTW = 100 cycles , at 13 MHz that is ~7.69 us */ 2341 usleep_range(10, 15); 2342 2343 /* Shut down GPIO is optional */ 2344 tc->sd_gpio = devm_gpiod_get_optional(dev, "shutdown", GPIOD_OUT_HIGH); 2345 if (IS_ERR(tc->sd_gpio)) 2346 return PTR_ERR(tc->sd_gpio); 2347 2348 if (tc->sd_gpio) { 2349 gpiod_set_value_cansleep(tc->sd_gpio, 0); 2350 usleep_range(5000, 10000); 2351 } 2352 2353 /* Reset GPIO is optional */ 2354 tc->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW); 2355 if (IS_ERR(tc->reset_gpio)) 2356 return PTR_ERR(tc->reset_gpio); 2357 2358 if (tc->reset_gpio) { 2359 gpiod_set_value_cansleep(tc->reset_gpio, 1); 2360 usleep_range(5000, 10000); 2361 } 2362 2363 tc->regmap = devm_regmap_init_i2c(client, &tc_regmap_config); 2364 if (IS_ERR(tc->regmap)) { 2365 ret = PTR_ERR(tc->regmap); 2366 dev_err(dev, "Failed to initialize regmap: %d\n", ret); 2367 return ret; 2368 } 2369 2370 ret = of_property_read_u32(dev->of_node, "toshiba,hpd-pin", 2371 &tc->hpd_pin); 2372 if (ret) { 2373 tc->hpd_pin = -ENODEV; 2374 } else { 2375 if (tc->hpd_pin < 0 || tc->hpd_pin > 1) { 2376 dev_err(dev, "failed to parse HPD number\n"); 2377 return -EINVAL; 2378 } 2379 } 2380 2381 if (client->irq > 0) { 2382 /* enable SysErr */ 2383 regmap_write(tc->regmap, INTCTL_G, INT_SYSERR); 2384 2385 ret = devm_request_threaded_irq(dev, client->irq, 2386 NULL, tc_irq_handler, 2387 IRQF_ONESHOT, 2388 "tc358767-irq", tc); 2389 if (ret) { 2390 dev_err(dev, "failed to register dp interrupt\n"); 2391 return ret; 2392 } 2393 2394 tc->have_irq = true; 2395 } 2396 2397 ret = regmap_read(tc->regmap, TC_IDREG, &tc->rev); 2398 if (ret) { 2399 dev_err(tc->dev, "can not read device ID: %d\n", ret); 2400 return ret; 2401 } 2402 2403 if ((tc->rev != 0x6601) && (tc->rev != 0x6603)) { 2404 dev_err(tc->dev, "invalid device ID: 0x%08x\n", tc->rev); 2405 return -EINVAL; 2406 } 2407 2408 tc->assr = (tc->rev == 0x6601); /* Enable ASSR for eDP panels */ 2409 2410 if (!tc->reset_gpio) { 2411 /* 2412 * If the reset pin isn't present, do a software reset. It isn't 2413 * as thorough as the hardware reset, as we can't reset the I2C 2414 * communication block for obvious reasons, but it's getting the 2415 * chip into a defined state. 2416 */ 2417 regmap_update_bits(tc->regmap, SYSRSTENB, 2418 ENBLCD0 | ENBBM | ENBDSIRX | ENBREG | ENBHDCP, 2419 0); 2420 regmap_update_bits(tc->regmap, SYSRSTENB, 2421 ENBLCD0 | ENBBM | ENBDSIRX | ENBREG | ENBHDCP, 2422 ENBLCD0 | ENBBM | ENBDSIRX | ENBREG | ENBHDCP); 2423 usleep_range(5000, 10000); 2424 } 2425 2426 if (tc->hpd_pin >= 0) { 2427 u32 lcnt_reg = tc->hpd_pin == 0 ? INT_GP0_LCNT : INT_GP1_LCNT; 2428 u32 h_lc = INT_GPIO_H(tc->hpd_pin) | INT_GPIO_LC(tc->hpd_pin); 2429 2430 /* Set LCNT to 2ms */ 2431 regmap_write(tc->regmap, lcnt_reg, 2432 clk_get_rate(tc->refclk) * 2 / 1000); 2433 /* We need the "alternate" mode for HPD */ 2434 regmap_write(tc->regmap, GPIOM, BIT(tc->hpd_pin)); 2435 2436 if (tc->have_irq) { 2437 /* enable H & LC */ 2438 regmap_update_bits(tc->regmap, INTCTL_G, h_lc, h_lc); 2439 } 2440 } 2441 2442 if (tc->bridge.type != DRM_MODE_CONNECTOR_DPI) { /* (e)DP output */ 2443 ret = tc_aux_link_setup(tc); 2444 if (ret) 2445 return ret; 2446 } 2447 2448 tc->bridge.of_node = dev->of_node; 2449 drm_bridge_add(&tc->bridge); 2450 2451 i2c_set_clientdata(client, tc); 2452 2453 if (tc->input_connector_dsi) { /* DSI input */ 2454 ret = tc_mipi_dsi_host_attach(tc); 2455 if (ret) { 2456 drm_bridge_remove(&tc->bridge); 2457 return ret; 2458 } 2459 } 2460 2461 return 0; 2462 } 2463 2464 static void tc_remove(struct i2c_client *client) 2465 { 2466 struct tc_data *tc = i2c_get_clientdata(client); 2467 2468 drm_bridge_remove(&tc->bridge); 2469 } 2470 2471 static const struct i2c_device_id tc358767_i2c_ids[] = { 2472 { "tc358767", 0 }, 2473 { } 2474 }; 2475 MODULE_DEVICE_TABLE(i2c, tc358767_i2c_ids); 2476 2477 static const struct of_device_id tc358767_of_ids[] = { 2478 { .compatible = "toshiba,tc358767", }, 2479 { } 2480 }; 2481 MODULE_DEVICE_TABLE(of, tc358767_of_ids); 2482 2483 static struct i2c_driver tc358767_driver = { 2484 .driver = { 2485 .name = "tc358767", 2486 .of_match_table = tc358767_of_ids, 2487 }, 2488 .id_table = tc358767_i2c_ids, 2489 .probe = tc_probe, 2490 .remove = tc_remove, 2491 }; 2492 module_i2c_driver(tc358767_driver); 2493 2494 MODULE_AUTHOR("Andrey Gusakov <andrey.gusakov@cogentembedded.com>"); 2495 MODULE_DESCRIPTION("tc358767 eDP encoder driver"); 2496 MODULE_LICENSE("GPL"); 2497