1 /* 2 * Copyright 2012 Red Hat Inc. 3 * 4 * Permission is hereby granted, free of charge, to any person obtaining a 5 * copy of this software and associated documentation files (the 6 * "Software"), to deal in the Software without restriction, including 7 * without limitation the rights to use, copy, modify, merge, publish, 8 * distribute, sub license, and/or sell copies of the Software, and to 9 * permit persons to whom the Software is furnished to do so, subject to 10 * the following conditions: 11 * 12 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR 13 * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, 14 * FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT SHALL 15 * THE COPYRIGHT HOLDERS, AUTHORS AND/OR ITS SUPPLIERS BE LIABLE FOR ANY CLAIM, 16 * DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR 17 * OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE 18 * USE OR OTHER DEALINGS IN THE SOFTWARE. 19 * 20 * The above copyright notice and this permission notice (including the 21 * next paragraph) shall be included in all copies or substantial portions 22 * of the Software. 23 * 24 */ 25 /* 26 * Authors: Dave Airlie <airlied@redhat.com> 27 */ 28 29 #include <linux/pci.h> 30 31 #include <drm/drm_atomic_helper.h> 32 #include <drm/drm_drv.h> 33 #include <drm/drm_gem.h> 34 #include <drm/drm_managed.h> 35 36 #include "ast_drv.h" 37 38 static bool ast_is_vga_enabled(struct drm_device *dev) 39 { 40 struct ast_device *ast = to_ast_device(dev); 41 u8 ch; 42 43 ch = ast_io_read8(ast, AST_IO_VGAER); 44 45 return !!(ch & 0x01); 46 } 47 48 static void ast_enable_vga(struct drm_device *dev) 49 { 50 struct ast_device *ast = to_ast_device(dev); 51 52 ast_io_write8(ast, AST_IO_VGAER, 0x01); 53 ast_io_write8(ast, AST_IO_VGAMR_W, 0x01); 54 } 55 56 /* 57 * Run this function as part of the HW device cleanup; not 58 * when the DRM device gets released. 59 */ 60 static void ast_enable_mmio_release(void *data) 61 { 62 struct ast_device *ast = data; 63 64 /* enable standard VGA decode */ 65 ast_set_index_reg(ast, AST_IO_VGACRI, 0xa1, 0x04); 66 } 67 68 static int ast_enable_mmio(struct ast_device *ast) 69 { 70 struct drm_device *dev = &ast->base; 71 72 ast_set_index_reg(ast, AST_IO_VGACRI, 0xa1, 0x06); 73 74 return devm_add_action_or_reset(dev->dev, ast_enable_mmio_release, ast); 75 } 76 77 static void ast_open_key(struct ast_device *ast) 78 { 79 ast_set_index_reg(ast, AST_IO_VGACRI, 0x80, 0xA8); 80 } 81 82 static int ast_device_config_init(struct ast_device *ast) 83 { 84 struct drm_device *dev = &ast->base; 85 struct pci_dev *pdev = to_pci_dev(dev->dev); 86 struct device_node *np = dev->dev->of_node; 87 uint32_t scu_rev = 0xffffffff; 88 u32 data; 89 u8 jregd0, jregd1; 90 91 /* 92 * Find configuration mode and read SCU revision 93 */ 94 95 ast->config_mode = ast_use_defaults; 96 97 /* Check if we have device-tree properties */ 98 if (np && !of_property_read_u32(np, "aspeed,scu-revision-id", &data)) { 99 /* We do, disable P2A access */ 100 ast->config_mode = ast_use_dt; 101 scu_rev = data; 102 } else if (pdev->device == PCI_CHIP_AST2000) { // Not all families have a P2A bridge 103 /* 104 * The BMC will set SCU 0x40 D[12] to 1 if the P2 bridge 105 * is disabled. We force using P2A if VGA only mode bit 106 * is set D[7] 107 */ 108 jregd0 = ast_get_index_reg_mask(ast, AST_IO_VGACRI, 0xd0, 0xff); 109 jregd1 = ast_get_index_reg_mask(ast, AST_IO_VGACRI, 0xd1, 0xff); 110 if (!(jregd0 & 0x80) || !(jregd1 & 0x10)) { 111 112 /* 113 * We have a P2A bridge and it is enabled. 114 */ 115 116 /* Patch AST2500/AST2510 */ 117 if ((pdev->revision & 0xf0) == 0x40) { 118 if (!(jregd0 & AST_VRAM_INIT_STATUS_MASK)) 119 ast_patch_ahb_2500(ast); 120 } 121 122 /* Double check that it's actually working */ 123 data = ast_read32(ast, 0xf004); 124 if ((data != 0xffffffff) && (data != 0x00)) { 125 ast->config_mode = ast_use_p2a; 126 127 /* Read SCU7c (silicon revision register) */ 128 ast_write32(ast, 0xf004, 0x1e6e0000); 129 ast_write32(ast, 0xf000, 0x1); 130 scu_rev = ast_read32(ast, 0x1207c); 131 } 132 } 133 } 134 135 switch (ast->config_mode) { 136 case ast_use_defaults: 137 drm_info(dev, "Using default configuration\n"); 138 break; 139 case ast_use_dt: 140 drm_info(dev, "Using device-tree for configuration\n"); 141 break; 142 case ast_use_p2a: 143 drm_info(dev, "Using P2A bridge for configuration\n"); 144 break; 145 } 146 147 /* 148 * Identify chipset 149 */ 150 151 if (pdev->revision >= 0x50) { 152 ast->chip = AST2600; 153 drm_info(dev, "AST 2600 detected\n"); 154 } else if (pdev->revision >= 0x40) { 155 switch (scu_rev & 0x300) { 156 case 0x0100: 157 ast->chip = AST2510; 158 drm_info(dev, "AST 2510 detected\n"); 159 break; 160 default: 161 ast->chip = AST2500; 162 drm_info(dev, "AST 2500 detected\n"); 163 } 164 } else if (pdev->revision >= 0x30) { 165 switch (scu_rev & 0x300) { 166 case 0x0100: 167 ast->chip = AST1400; 168 drm_info(dev, "AST 1400 detected\n"); 169 break; 170 default: 171 ast->chip = AST2400; 172 drm_info(dev, "AST 2400 detected\n"); 173 } 174 } else if (pdev->revision >= 0x20) { 175 switch (scu_rev & 0x300) { 176 case 0x0000: 177 ast->chip = AST1300; 178 drm_info(dev, "AST 1300 detected\n"); 179 break; 180 default: 181 ast->chip = AST2300; 182 drm_info(dev, "AST 2300 detected\n"); 183 break; 184 } 185 } else if (pdev->revision >= 0x10) { 186 switch (scu_rev & 0x0300) { 187 case 0x0200: 188 ast->chip = AST1100; 189 drm_info(dev, "AST 1100 detected\n"); 190 break; 191 case 0x0100: 192 ast->chip = AST2200; 193 drm_info(dev, "AST 2200 detected\n"); 194 break; 195 case 0x0000: 196 ast->chip = AST2150; 197 drm_info(dev, "AST 2150 detected\n"); 198 break; 199 default: 200 ast->chip = AST2100; 201 drm_info(dev, "AST 2100 detected\n"); 202 break; 203 } 204 } else { 205 ast->chip = AST2000; 206 drm_info(dev, "AST 2000 detected\n"); 207 } 208 209 return 0; 210 } 211 212 static void ast_detect_widescreen(struct ast_device *ast) 213 { 214 u8 jreg; 215 216 /* Check if we support wide screen */ 217 switch (AST_GEN(ast)) { 218 case 1: 219 ast->support_wide_screen = false; 220 break; 221 default: 222 jreg = ast_get_index_reg_mask(ast, AST_IO_VGACRI, 0xd0, 0xff); 223 if (!(jreg & 0x80)) 224 ast->support_wide_screen = true; 225 else if (jreg & 0x01) 226 ast->support_wide_screen = true; 227 else { 228 ast->support_wide_screen = false; 229 if (ast->chip == AST1300) 230 ast->support_wide_screen = true; 231 if (ast->chip == AST1400) 232 ast->support_wide_screen = true; 233 if (ast->chip == AST2510) 234 ast->support_wide_screen = true; 235 if (IS_AST_GEN7(ast)) 236 ast->support_wide_screen = true; 237 } 238 break; 239 } 240 } 241 242 static void ast_detect_tx_chip(struct ast_device *ast, bool need_post) 243 { 244 struct drm_device *dev = &ast->base; 245 u8 jreg; 246 247 /* Check 3rd Tx option (digital output afaik) */ 248 ast->tx_chip_types |= AST_TX_NONE_BIT; 249 250 /* 251 * VGACRA3 Enhanced Color Mode Register, check if DVO is already 252 * enabled, in that case, assume we have a SIL164 TMDS transmitter 253 * 254 * Don't make that assumption if we the chip wasn't enabled and 255 * is at power-on reset, otherwise we'll incorrectly "detect" a 256 * SIL164 when there is none. 257 */ 258 if (!need_post) { 259 jreg = ast_get_index_reg_mask(ast, AST_IO_VGACRI, 0xa3, 0xff); 260 if (jreg & 0x80) 261 ast->tx_chip_types = AST_TX_SIL164_BIT; 262 } 263 264 if (IS_AST_GEN4(ast) || IS_AST_GEN5(ast) || IS_AST_GEN6(ast)) { 265 /* 266 * On AST GEN4+, look the configuration set by the SoC in 267 * the SOC scratch register #1 bits 11:8 (interestingly marked 268 * as "reserved" in the spec) 269 */ 270 jreg = ast_get_index_reg_mask(ast, AST_IO_VGACRI, 0xd1, 0xff); 271 switch (jreg) { 272 case 0x04: 273 ast->tx_chip_types = AST_TX_SIL164_BIT; 274 break; 275 case 0x08: 276 ast->dp501_fw_addr = drmm_kzalloc(dev, 32*1024, GFP_KERNEL); 277 if (ast->dp501_fw_addr) { 278 /* backup firmware */ 279 if (ast_backup_fw(dev, ast->dp501_fw_addr, 32*1024)) { 280 drmm_kfree(dev, ast->dp501_fw_addr); 281 ast->dp501_fw_addr = NULL; 282 } 283 } 284 fallthrough; 285 case 0x0c: 286 ast->tx_chip_types = AST_TX_DP501_BIT; 287 } 288 } else if (IS_AST_GEN7(ast)) { 289 if (ast_get_index_reg_mask(ast, AST_IO_VGACRI, 0xD1, TX_TYPE_MASK) == 290 ASTDP_DPMCU_TX) { 291 ast->tx_chip_types = AST_TX_ASTDP_BIT; 292 ast_dp_launch(&ast->base); 293 } 294 } 295 296 /* Print stuff for diagnostic purposes */ 297 if (ast->tx_chip_types & AST_TX_NONE_BIT) 298 drm_info(dev, "Using analog VGA\n"); 299 if (ast->tx_chip_types & AST_TX_SIL164_BIT) 300 drm_info(dev, "Using Sil164 TMDS transmitter\n"); 301 if (ast->tx_chip_types & AST_TX_DP501_BIT) 302 drm_info(dev, "Using DP501 DisplayPort transmitter\n"); 303 if (ast->tx_chip_types & AST_TX_ASTDP_BIT) 304 drm_info(dev, "Using ASPEED DisplayPort transmitter\n"); 305 } 306 307 static int ast_get_dram_info(struct drm_device *dev) 308 { 309 struct device_node *np = dev->dev->of_node; 310 struct ast_device *ast = to_ast_device(dev); 311 uint32_t mcr_cfg, mcr_scu_mpll, mcr_scu_strap; 312 uint32_t denum, num, div, ref_pll, dsel; 313 314 switch (ast->config_mode) { 315 case ast_use_dt: 316 /* 317 * If some properties are missing, use reasonable 318 * defaults for GEN5 319 */ 320 if (of_property_read_u32(np, "aspeed,mcr-configuration", 321 &mcr_cfg)) 322 mcr_cfg = 0x00000577; 323 if (of_property_read_u32(np, "aspeed,mcr-scu-mpll", 324 &mcr_scu_mpll)) 325 mcr_scu_mpll = 0x000050C0; 326 if (of_property_read_u32(np, "aspeed,mcr-scu-strap", 327 &mcr_scu_strap)) 328 mcr_scu_strap = 0; 329 break; 330 case ast_use_p2a: 331 ast_write32(ast, 0xf004, 0x1e6e0000); 332 ast_write32(ast, 0xf000, 0x1); 333 mcr_cfg = ast_read32(ast, 0x10004); 334 mcr_scu_mpll = ast_read32(ast, 0x10120); 335 mcr_scu_strap = ast_read32(ast, 0x10170); 336 break; 337 case ast_use_defaults: 338 default: 339 ast->dram_bus_width = 16; 340 ast->dram_type = AST_DRAM_1Gx16; 341 if (IS_AST_GEN6(ast)) 342 ast->mclk = 800; 343 else 344 ast->mclk = 396; 345 return 0; 346 } 347 348 if (mcr_cfg & 0x40) 349 ast->dram_bus_width = 16; 350 else 351 ast->dram_bus_width = 32; 352 353 if (IS_AST_GEN6(ast)) { 354 switch (mcr_cfg & 0x03) { 355 case 0: 356 ast->dram_type = AST_DRAM_1Gx16; 357 break; 358 default: 359 case 1: 360 ast->dram_type = AST_DRAM_2Gx16; 361 break; 362 case 2: 363 ast->dram_type = AST_DRAM_4Gx16; 364 break; 365 case 3: 366 ast->dram_type = AST_DRAM_8Gx16; 367 break; 368 } 369 } else if (IS_AST_GEN4(ast) || IS_AST_GEN5(ast)) { 370 switch (mcr_cfg & 0x03) { 371 case 0: 372 ast->dram_type = AST_DRAM_512Mx16; 373 break; 374 default: 375 case 1: 376 ast->dram_type = AST_DRAM_1Gx16; 377 break; 378 case 2: 379 ast->dram_type = AST_DRAM_2Gx16; 380 break; 381 case 3: 382 ast->dram_type = AST_DRAM_4Gx16; 383 break; 384 } 385 } else { 386 switch (mcr_cfg & 0x0c) { 387 case 0: 388 case 4: 389 ast->dram_type = AST_DRAM_512Mx16; 390 break; 391 case 8: 392 if (mcr_cfg & 0x40) 393 ast->dram_type = AST_DRAM_1Gx16; 394 else 395 ast->dram_type = AST_DRAM_512Mx32; 396 break; 397 case 0xc: 398 ast->dram_type = AST_DRAM_1Gx32; 399 break; 400 } 401 } 402 403 if (mcr_scu_strap & 0x2000) 404 ref_pll = 14318; 405 else 406 ref_pll = 12000; 407 408 denum = mcr_scu_mpll & 0x1f; 409 num = (mcr_scu_mpll & 0x3fe0) >> 5; 410 dsel = (mcr_scu_mpll & 0xc000) >> 14; 411 switch (dsel) { 412 case 3: 413 div = 0x4; 414 break; 415 case 2: 416 case 1: 417 div = 0x2; 418 break; 419 default: 420 div = 0x1; 421 break; 422 } 423 ast->mclk = ref_pll * (num + 2) / ((denum + 2) * (div * 1000)); 424 return 0; 425 } 426 427 struct ast_device *ast_device_create(const struct drm_driver *drv, 428 struct pci_dev *pdev, 429 unsigned long flags) 430 { 431 struct drm_device *dev; 432 struct ast_device *ast; 433 bool need_post = false; 434 int ret = 0; 435 436 ast = devm_drm_dev_alloc(&pdev->dev, drv, struct ast_device, base); 437 if (IS_ERR(ast)) 438 return ast; 439 dev = &ast->base; 440 441 pci_set_drvdata(pdev, dev); 442 443 ret = drmm_mutex_init(dev, &ast->ioregs_lock); 444 if (ret) 445 return ERR_PTR(ret); 446 447 ast->regs = pcim_iomap(pdev, 1, 0); 448 if (!ast->regs) 449 return ERR_PTR(-EIO); 450 451 /* 452 * After AST2500, MMIO is enabled by default, and it should be adopted 453 * to be compatible with Arm. 454 */ 455 if (pdev->revision >= 0x40) { 456 ast->ioregs = ast->regs + AST_IO_MM_OFFSET; 457 } else if (!(pci_resource_flags(pdev, 2) & IORESOURCE_IO)) { 458 drm_info(dev, "platform has no IO space, trying MMIO\n"); 459 ast->ioregs = ast->regs + AST_IO_MM_OFFSET; 460 } 461 462 /* "map" IO regs if the above hasn't done so already */ 463 if (!ast->ioregs) { 464 ast->ioregs = pcim_iomap(pdev, 2, 0); 465 if (!ast->ioregs) 466 return ERR_PTR(-EIO); 467 } 468 469 if (!ast_is_vga_enabled(dev)) { 470 drm_info(dev, "VGA not enabled on entry, requesting chip POST\n"); 471 need_post = true; 472 } 473 474 /* 475 * If VGA isn't enabled, we need to enable now or subsequent 476 * access to the scratch registers will fail. 477 */ 478 if (need_post) 479 ast_enable_vga(dev); 480 481 /* Enable extended register access */ 482 ast_open_key(ast); 483 ret = ast_enable_mmio(ast); 484 if (ret) 485 return ERR_PTR(ret); 486 487 ret = ast_device_config_init(ast); 488 if (ret) 489 return ERR_PTR(ret); 490 491 ast_detect_widescreen(ast); 492 ast_detect_tx_chip(ast, need_post); 493 494 ret = ast_get_dram_info(dev); 495 if (ret) 496 return ERR_PTR(ret); 497 498 drm_info(dev, "dram MCLK=%u Mhz type=%d bus_width=%d\n", 499 ast->mclk, ast->dram_type, ast->dram_bus_width); 500 501 if (need_post) 502 ast_post_gpu(dev); 503 504 ret = ast_mm_init(ast); 505 if (ret) 506 return ERR_PTR(ret); 507 508 /* map reserved buffer */ 509 ast->dp501_fw_buf = NULL; 510 if (ast->vram_size < pci_resource_len(pdev, 0)) { 511 ast->dp501_fw_buf = pci_iomap_range(pdev, 0, ast->vram_size, 0); 512 if (!ast->dp501_fw_buf) 513 drm_info(dev, "failed to map reserved buffer!\n"); 514 } 515 516 ret = ast_mode_config_init(ast); 517 if (ret) 518 return ERR_PTR(ret); 519 520 return ast; 521 } 522