xref: /linux/drivers/firmware/arm_scmi/driver.c (revision 497e6b37b0099dc415578488287fd84fb74433eb)

// SPDX-License-Identifier: GPL-2.0
/*
 * System Control and Management Interface (SCMI) Message Protocol driver
 *
 * SCMI Message Protocol is used between the System Control Processor(SCP)
 * and the Application Processors(AP). The Message Handling Unit(MHU)
 * provides a mechanism for inter-processor communication between SCP's
 * Cortex M3 and AP.
 *
 * SCP offers control and management of the core/cluster power states,
 * various power domain DVFS including the core/cluster, certain system
 * clocks configuration, thermal sensors and many others.
 *
 * Copyright (C) 2018-2021 ARM Ltd.
 */

#include <linux/bitmap.h>
#include <linux/device.h>
#include <linux/export.h>
#include <linux/idr.h>
#include <linux/io.h>
#include <linux/io-64-nonatomic-hi-lo.h>
#include <linux/kernel.h>
#include <linux/ktime.h>
#include <linux/hashtable.h>
#include <linux/list.h>
#include <linux/module.h>
#include <linux/of_address.h>
#include <linux/of_device.h>
#include <linux/processor.h>
#include <linux/refcount.h>
#include <linux/slab.h>

#include "common.h"
#include "notify.h"

#define CREATE_TRACE_POINTS
#include <trace/events/scmi.h>

enum scmi_error_codes {
	SCMI_SUCCESS = 0,	/* Success */
	SCMI_ERR_SUPPORT = -1,	/* Not supported */
	SCMI_ERR_PARAMS = -2,	/* Invalid Parameters */
	SCMI_ERR_ACCESS = -3,	/* Invalid access/permission denied */
	SCMI_ERR_ENTRY = -4,	/* Not found */
	SCMI_ERR_RANGE = -5,	/* Value out of range */
	SCMI_ERR_BUSY = -6,	/* Device busy */
	SCMI_ERR_COMMS = -7,	/* Communication Error */
	SCMI_ERR_GENERIC = -8,	/* Generic Error */
	SCMI_ERR_HARDWARE = -9,	/* Hardware Error */
	SCMI_ERR_PROTOCOL = -10,/* Protocol Error */
};

/* List of all SCMI devices active in system */
static LIST_HEAD(scmi_list);
/* Protection for the entire list */
static DEFINE_MUTEX(scmi_list_mutex);
/* Track the unique id for the transfers for debug & profiling purpose */
static atomic_t transfer_last_id;

static DEFINE_IDR(scmi_requested_devices);
static DEFINE_MUTEX(scmi_requested_devices_mtx);

/* Track globally the creation of SCMI SystemPower related devices */
static bool scmi_syspower_registered;
/* Protect access to scmi_syspower_registered */
static DEFINE_MUTEX(scmi_syspower_mtx);

struct scmi_requested_dev {
	const struct scmi_device_id *id_table;
	struct list_head node;
};

/**
 * struct scmi_xfers_info - Structure to manage transfer information
 *
 * @xfer_alloc_table: Bitmap table for allocated messages.
 *	Index of this bitmap table is also used for message
 *	sequence identifier.
 * @xfer_lock: Protection for message allocation
 * @max_msg: Maximum number of messages that can be pending
 * @free_xfers: A free list for available to use xfers. It is initialized with
 *		a number of xfers equal to the maximum allowed in-flight
 *		messages.
 * @pending_xfers: An hashtable, indexed by msg_hdr.seq, used to keep all the
 *		   currently in-flight messages.
 */
struct scmi_xfers_info {
	unsigned long *xfer_alloc_table;
	spinlock_t xfer_lock;
	int max_msg;
	struct hlist_head free_xfers;
	DECLARE_HASHTABLE(pending_xfers, SCMI_PENDING_XFERS_HT_ORDER_SZ);
};

/**
 * struct scmi_protocol_instance  - Describe an initialized protocol instance.
 * @handle: Reference to the SCMI handle associated to this protocol instance.
 * @proto: A reference to the protocol descriptor.
 * @gid: A reference for per-protocol devres management.
 * @users: A refcount to track effective users of this protocol.
 * @priv: Reference for optional protocol private data.
 * @ph: An embedded protocol handle that will be passed down to protocol
 *	initialization code to identify this instance.
 *
 * Each protocol is initialized independently once for each SCMI platform in
 * which is defined by DT and implemented by the SCMI server fw.
 */
struct scmi_protocol_instance {
	const struct scmi_handle	*handle;
	const struct scmi_protocol	*proto;
	void				*gid;
	refcount_t			users;
	void				*priv;
	struct scmi_protocol_handle	ph;
};

#define ph_to_pi(h)	container_of(h, struct scmi_protocol_instance, ph)

/**
 * struct scmi_info - Structure representing a SCMI instance
 *
 * @dev: Device pointer
 * @desc: SoC description for this instance
 * @version: SCMI revision information containing protocol version,
 *	implementation version and (sub-)vendor identification.
 * @handle: Instance of SCMI handle to send to clients
 * @tx_minfo: Universal Transmit Message management info
 * @rx_minfo: Universal Receive Message management info
 * @tx_idr: IDR object to map protocol id to Tx channel info pointer
 * @rx_idr: IDR object to map protocol id to Rx channel info pointer
 * @protocols: IDR for protocols' instance descriptors initialized for
 *	       this SCMI instance: populated on protocol's first attempted
 *	       usage.
 * @protocols_mtx: A mutex to protect protocols instances initialization.
 * @protocols_imp: List of protocols implemented, currently maximum of
 *		   scmi_revision_info.num_protocols elements allocated by the
 *		   base protocol
 * @active_protocols: IDR storing device_nodes for protocols actually defined
 *		      in the DT and confirmed as implemented by fw.
 * @atomic_threshold: Optional system wide DT-configured threshold, expressed
 *		      in microseconds, for atomic operations.
 *		      Only SCMI synchronous commands reported by the platform
 *		      to have an execution latency lesser-equal to the threshold
 *		      should be considered for atomic mode operation: such
 *		      decision is finally left up to the SCMI drivers.
 * @notify_priv: Pointer to private data structure specific to notifications.
 * @node: List head
 * @users: Number of users of this instance
 */
struct scmi_info {
	struct device *dev;
	const struct scmi_desc *desc;
	struct scmi_revision_info version;
	struct scmi_handle handle;
	struct scmi_xfers_info tx_minfo;
	struct scmi_xfers_info rx_minfo;
	struct idr tx_idr;
	struct idr rx_idr;
	struct idr protocols;
	/* Ensure mutual exclusive access to protocols instance array */
	struct mutex protocols_mtx;
	u8 *protocols_imp;
	struct idr active_protocols;
	unsigned int atomic_threshold;
	void *notify_priv;
	struct list_head node;
	int users;
};

#define handle_to_scmi_info(h)	container_of(h, struct scmi_info, handle)

static const int scmi_linux_errmap[] = {
	/* better than switch case as long as return value is continuous */
	0,			/* SCMI_SUCCESS */
	-EOPNOTSUPP,		/* SCMI_ERR_SUPPORT */
	-EINVAL,		/* SCMI_ERR_PARAM */
	-EACCES,		/* SCMI_ERR_ACCESS */
	-ENOENT,		/* SCMI_ERR_ENTRY */
	-ERANGE,		/* SCMI_ERR_RANGE */
	-EBUSY,			/* SCMI_ERR_BUSY */
	-ECOMM,			/* SCMI_ERR_COMMS */
	-EIO,			/* SCMI_ERR_GENERIC */
	-EREMOTEIO,		/* SCMI_ERR_HARDWARE */
	-EPROTO,		/* SCMI_ERR_PROTOCOL */
};

static inline int scmi_to_linux_errno(int errno)
{
	int err_idx = -errno;

	if (err_idx >= SCMI_SUCCESS && err_idx < ARRAY_SIZE(scmi_linux_errmap))
		return scmi_linux_errmap[err_idx];
	return -EIO;
}

void scmi_notification_instance_data_set(const struct scmi_handle *handle,
					 void *priv)
{
	struct scmi_info *info = handle_to_scmi_info(handle);

	info->notify_priv = priv;
	/* Ensure updated protocol private date are visible */
	smp_wmb();
}

void *scmi_notification_instance_data_get(const struct scmi_handle *handle)
{
	struct scmi_info *info = handle_to_scmi_info(handle);

	/* Ensure protocols_private_data has been updated */
	smp_rmb();
	return info->notify_priv;
}

/**
 * scmi_xfer_token_set  - Reserve and set new token for the xfer at hand
 *
 * @minfo: Pointer to Tx/Rx Message management info based on channel type
 * @xfer: The xfer to act upon
 *
 * Pick the next unused monotonically increasing token and set it into
 * xfer->hdr.seq: picking a monotonically increasing value avoids immediate
 * reuse of freshly completed or timed-out xfers, thus mitigating the risk
 * of incorrect association of a late and expired xfer with a live in-flight
 * transaction, both happening to re-use the same token identifier.
 *
 * Since platform is NOT required to answer our request in-order we should
 * account for a few rare but possible scenarios:
 *
 *  - exactly 'next_token' may be NOT available so pick xfer_id >= next_token
 *    using find_next_zero_bit() starting from candidate next_token bit
 *
 *  - all tokens ahead upto (MSG_TOKEN_ID_MASK - 1) are used in-flight but we
 *    are plenty of free tokens at start, so try a second pass using
 *    find_next_zero_bit() and starting from 0.
 *
 *  X = used in-flight
 *
 * Normal
 * ------
 *
 *		|- xfer_id picked
 *   -----------+----------------------------------------------------------
 *   | | |X|X|X| | | | | | ... ... ... ... ... ... ... ... ... ... ...|X|X|
 *   ----------------------------------------------------------------------
 *		^
 *		|- next_token
 *
 * Out-of-order pending at start
 * -----------------------------
 *
 *	  |- xfer_id picked, last_token fixed
 *   -----+----------------------------------------------------------------
 *   |X|X| | | | |X|X| ... ... ... ... ... ... ... ... ... ... ... ...|X| |
 *   ----------------------------------------------------------------------
 *    ^
 *    |- next_token
 *
 *
 * Out-of-order pending at end
 * ---------------------------
 *
 *	  |- xfer_id picked, last_token fixed
 *   -----+----------------------------------------------------------------
 *   |X|X| | | | |X|X| ... ... ... ... ... ... ... ... ... ... |X|X|X||X|X|
 *   ----------------------------------------------------------------------
 *								^
 *								|- next_token
 *
 * Context: Assumes to be called with @xfer_lock already acquired.
 *
 * Return: 0 on Success or error
 */
static int scmi_xfer_token_set(struct scmi_xfers_info *minfo,
			       struct scmi_xfer *xfer)
{
	unsigned long xfer_id, next_token;

	/*
	 * Pick a candidate monotonic token in range [0, MSG_TOKEN_MAX - 1]
	 * using the pre-allocated transfer_id as a base.
	 * Note that the global transfer_id is shared across all message types
	 * so there could be holes in the allocated set of monotonic sequence
	 * numbers, but that is going to limit the effectiveness of the
	 * mitigation only in very rare limit conditions.
	 */
	next_token = (xfer->transfer_id & (MSG_TOKEN_MAX - 1));

	/* Pick the next available xfer_id >= next_token */
	xfer_id = find_next_zero_bit(minfo->xfer_alloc_table,
				     MSG_TOKEN_MAX, next_token);
	if (xfer_id == MSG_TOKEN_MAX) {
		/*
		 * After heavily out-of-order responses, there are no free
		 * tokens ahead, but only at start of xfer_alloc_table so
		 * try again from the beginning.
		 */
		xfer_id = find_next_zero_bit(minfo->xfer_alloc_table,
					     MSG_TOKEN_MAX, 0);
		/*
		 * Something is wrong if we got here since there can be a
		 * maximum number of (MSG_TOKEN_MAX - 1) in-flight messages
		 * but we have not found any free token [0, MSG_TOKEN_MAX - 1].
		 */
		if (WARN_ON_ONCE(xfer_id == MSG_TOKEN_MAX))
			return -ENOMEM;
	}

	/* Update +/- last_token accordingly if we skipped some hole */
	if (xfer_id != next_token)
		atomic_add((int)(xfer_id - next_token), &transfer_last_id);

	/* Set in-flight */
	set_bit(xfer_id, minfo->xfer_alloc_table);
	xfer->hdr.seq = (u16)xfer_id;

	return 0;
}

/**
 * scmi_xfer_token_clear  - Release the token
 *
 * @minfo: Pointer to Tx/Rx Message management info based on channel type
 * @xfer: The xfer to act upon
 */
static inline void scmi_xfer_token_clear(struct scmi_xfers_info *minfo,
					 struct scmi_xfer *xfer)
{
	clear_bit(xfer->hdr.seq, minfo->xfer_alloc_table);
}

/**
 * scmi_xfer_get() - Allocate one message
 *
 * @handle: Pointer to SCMI entity handle
 * @minfo: Pointer to Tx/Rx Message management info based on channel type
 * @set_pending: If true a monotonic token is picked and the xfer is added to
 *		 the pending hash table.
 *
 * Helper function which is used by various message functions that are
 * exposed to clients of this driver for allocating a message traffic event.
 *
 * Picks an xfer from the free list @free_xfers (if any available) and, if
 * required, sets a monotonically increasing token and stores the inflight xfer
 * into the @pending_xfers hashtable for later retrieval.
 *
 * The successfully initialized xfer is refcounted.
 *
 * Context: Holds @xfer_lock while manipulating @xfer_alloc_table and
 *	    @free_xfers.
 *
 * Return: 0 if all went fine, else corresponding error.
 */
static struct scmi_xfer *scmi_xfer_get(const struct scmi_handle *handle,
				       struct scmi_xfers_info *minfo,
				       bool set_pending)
{
	int ret;
	unsigned long flags;
	struct scmi_xfer *xfer;

	spin_lock_irqsave(&minfo->xfer_lock, flags);
	if (hlist_empty(&minfo->free_xfers)) {
		spin_unlock_irqrestore(&minfo->xfer_lock, flags);
		return ERR_PTR(-ENOMEM);
	}

	/* grab an xfer from the free_list */
	xfer = hlist_entry(minfo->free_xfers.first, struct scmi_xfer, node);
	hlist_del_init(&xfer->node);

	/*
	 * Allocate transfer_id early so that can be used also as base for
	 * monotonic sequence number generation if needed.
	 */
	xfer->transfer_id = atomic_inc_return(&transfer_last_id);

	if (set_pending) {
		/* Pick and set monotonic token */
		ret = scmi_xfer_token_set(minfo, xfer);
		if (!ret) {
			hash_add(minfo->pending_xfers, &xfer->node,
				 xfer->hdr.seq);
			xfer->pending = true;
		} else {
			dev_err(handle->dev,
				"Failed to get monotonic token %d\n", ret);
			hlist_add_head(&xfer->node, &minfo->free_xfers);
			xfer = ERR_PTR(ret);
		}
	}

	if (!IS_ERR(xfer)) {
		refcount_set(&xfer->users, 1);
		atomic_set(&xfer->busy, SCMI_XFER_FREE);
	}
	spin_unlock_irqrestore(&minfo->xfer_lock, flags);

	return xfer;
}

/**
 * __scmi_xfer_put() - Release a message
 *
 * @minfo: Pointer to Tx/Rx Message management info based on channel type
 * @xfer: message that was reserved by scmi_xfer_get
 *
 * After refcount check, possibly release an xfer, clearing the token slot,
 * removing xfer from @pending_xfers and putting it back into free_xfers.
 *
 * This holds a spinlock to maintain integrity of internal data structures.
 */
static void
__scmi_xfer_put(struct scmi_xfers_info *minfo, struct scmi_xfer *xfer)
{
	unsigned long flags;

	spin_lock_irqsave(&minfo->xfer_lock, flags);
	if (refcount_dec_and_test(&xfer->users)) {
		if (xfer->pending) {
			scmi_xfer_token_clear(minfo, xfer);
			hash_del(&xfer->node);
			xfer->pending = false;
		}
		hlist_add_head(&xfer->node, &minfo->free_xfers);
	}
	spin_unlock_irqrestore(&minfo->xfer_lock, flags);
}

/**
 * scmi_xfer_lookup_unlocked  -  Helper to lookup an xfer_id
 *
 * @minfo: Pointer to Tx/Rx Message management info based on channel type
 * @xfer_id: Token ID to lookup in @pending_xfers
 *
 * Refcounting is untouched.
 *
 * Context: Assumes to be called with @xfer_lock already acquired.
 *
 * Return: A valid xfer on Success or error otherwise
 */
static struct scmi_xfer *
scmi_xfer_lookup_unlocked(struct scmi_xfers_info *minfo, u16 xfer_id)
{
	struct scmi_xfer *xfer = NULL;

	if (test_bit(xfer_id, minfo->xfer_alloc_table))
		xfer = XFER_FIND(minfo->pending_xfers, xfer_id);

	return xfer ?: ERR_PTR(-EINVAL);
}

/**
 * scmi_msg_response_validate  - Validate message type against state of related
 * xfer
 *
 * @cinfo: A reference to the channel descriptor.
 * @msg_type: Message type to check
 * @xfer: A reference to the xfer to validate against @msg_type
 *
 * This function checks if @msg_type is congruent with the current state of
 * a pending @xfer; if an asynchronous delayed response is received before the
 * related synchronous response (Out-of-Order Delayed Response) the missing
 * synchronous response is assumed to be OK and completed, carrying on with the
 * Delayed Response: this is done to address the case in which the underlying
 * SCMI transport can deliver such out-of-order responses.
 *
 * Context: Assumes to be called with xfer->lock already acquired.
 *
 * Return: 0 on Success, error otherwise
 */
static inline int scmi_msg_response_validate(struct scmi_chan_info *cinfo,
					     u8 msg_type,
					     struct scmi_xfer *xfer)
{
	/*
	 * Even if a response was indeed expected on this slot at this point,
	 * a buggy platform could wrongly reply feeding us an unexpected
	 * delayed response we're not prepared to handle: bail-out safely
	 * blaming firmware.
	 */
	if (msg_type == MSG_TYPE_DELAYED_RESP && !xfer->async_done) {
		dev_err(cinfo->dev,
			"Delayed Response for %d not expected! Buggy F/W ?\n",
			xfer->hdr.seq);
		return -EINVAL;
	}

	switch (xfer->state) {
	case SCMI_XFER_SENT_OK:
		if (msg_type == MSG_TYPE_DELAYED_RESP) {
			/*
			 * Delayed Response expected but delivered earlier.
			 * Assume message RESPONSE was OK and skip state.
			 */
			xfer->hdr.status = SCMI_SUCCESS;
			xfer->state = SCMI_XFER_RESP_OK;
			complete(&xfer->done);
			dev_warn(cinfo->dev,
				 "Received valid OoO Delayed Response for %d\n",
				 xfer->hdr.seq);
		}
		break;
	case SCMI_XFER_RESP_OK:
		if (msg_type != MSG_TYPE_DELAYED_RESP)
			return -EINVAL;
		break;
	case SCMI_XFER_DRESP_OK:
		/* No further message expected once in SCMI_XFER_DRESP_OK */
		return -EINVAL;
	}

	return 0;
}

/**
 * scmi_xfer_state_update  - Update xfer state
 *
 * @xfer: A reference to the xfer to update
 * @msg_type: Type of message being processed.
 *
 * Note that this message is assumed to have been already successfully validated
 * by @scmi_msg_response_validate(), so here we just update the state.
 *
 * Context: Assumes to be called on an xfer exclusively acquired using the
 *	    busy flag.
 */
static inline void scmi_xfer_state_update(struct scmi_xfer *xfer, u8 msg_type)
{
	xfer->hdr.type = msg_type;

	/* Unknown command types were already discarded earlier */
	if (xfer->hdr.type == MSG_TYPE_COMMAND)
		xfer->state = SCMI_XFER_RESP_OK;
	else
		xfer->state = SCMI_XFER_DRESP_OK;
}

static bool scmi_xfer_acquired(struct scmi_xfer *xfer)
{
	int ret;

	ret = atomic_cmpxchg(&xfer->busy, SCMI_XFER_FREE, SCMI_XFER_BUSY);

	return ret == SCMI_XFER_FREE;
}

/**
 * scmi_xfer_command_acquire  -  Helper to lookup and acquire a command xfer
 *
 * @cinfo: A reference to the channel descriptor.
 * @msg_hdr: A message header to use as lookup key
 *
 * When a valid xfer is found for the sequence number embedded in the provided
 * msg_hdr, reference counting is properly updated and exclusive access to this
 * xfer is granted till released with @scmi_xfer_command_release.
 *
 * Return: A valid @xfer on Success or error otherwise.
 */
static inline struct scmi_xfer *
scmi_xfer_command_acquire(struct scmi_chan_info *cinfo, u32 msg_hdr)
{
	int ret;
	unsigned long flags;
	struct scmi_xfer *xfer;
	struct scmi_info *info = handle_to_scmi_info(cinfo->handle);
	struct scmi_xfers_info *minfo = &info->tx_minfo;
	u8 msg_type = MSG_XTRACT_TYPE(msg_hdr);
	u16 xfer_id = MSG_XTRACT_TOKEN(msg_hdr);

	/* Are we even expecting this? */
	spin_lock_irqsave(&minfo->xfer_lock, flags);
	xfer = scmi_xfer_lookup_unlocked(minfo, xfer_id);
	if (IS_ERR(xfer)) {
		dev_err(cinfo->dev,
			"Message for %d type %d is not expected!\n",
			xfer_id, msg_type);
		spin_unlock_irqrestore(&minfo->xfer_lock, flags);
		return xfer;
	}
	refcount_inc(&xfer->users);
	spin_unlock_irqrestore(&minfo->xfer_lock, flags);

	spin_lock_irqsave(&xfer->lock, flags);
	ret = scmi_msg_response_validate(cinfo, msg_type, xfer);
	/*
	 * If a pending xfer was found which was also in a congruent state with
	 * the received message, acquire exclusive access to it setting the busy
	 * flag.
	 * Spins only on the rare limit condition of concurrent reception of
	 * RESP and DRESP for the same xfer.
	 */
	if (!ret) {
		spin_until_cond(scmi_xfer_acquired(xfer));
		scmi_xfer_state_update(xfer, msg_type);
	}
	spin_unlock_irqrestore(&xfer->lock, flags);

	if (ret) {
		dev_err(cinfo->dev,
			"Invalid message type:%d for %d - HDR:0x%X  state:%d\n",
			msg_type, xfer_id, msg_hdr, xfer->state);
		/* On error the refcount incremented above has to be dropped */
		__scmi_xfer_put(minfo, xfer);
		xfer = ERR_PTR(-EINVAL);
	}

	return xfer;
}

static inline void scmi_xfer_command_release(struct scmi_info *info,
					     struct scmi_xfer *xfer)
{
	atomic_set(&xfer->busy, SCMI_XFER_FREE);
	__scmi_xfer_put(&info->tx_minfo, xfer);
}

static inline void scmi_clear_channel(struct scmi_info *info,
				      struct scmi_chan_info *cinfo)
{
	if (info->desc->ops->clear_channel)
		info->desc->ops->clear_channel(cinfo);
}

static inline bool is_polling_required(struct scmi_chan_info *cinfo,
				       struct scmi_info *info)
{
	return cinfo->no_completion_irq || info->desc->force_polling;
}

static inline bool is_transport_polling_capable(struct scmi_info *info)
{
	return info->desc->ops->poll_done ||
		info->desc->sync_cmds_completed_on_ret;
}

static inline bool is_polling_enabled(struct scmi_chan_info *cinfo,
				      struct scmi_info *info)
{
	return is_polling_required(cinfo, info) &&
		is_transport_polling_capable(info);
}

static void scmi_handle_notification(struct scmi_chan_info *cinfo,
				     u32 msg_hdr, void *priv)
{
	struct scmi_xfer *xfer;
	struct device *dev = cinfo->dev;
	struct scmi_info *info = handle_to_scmi_info(cinfo->handle);
	struct scmi_xfers_info *minfo = &info->rx_minfo;
	ktime_t ts;

	ts = ktime_get_boottime();
	xfer = scmi_xfer_get(cinfo->handle, minfo, false);
	if (IS_ERR(xfer)) {
		dev_err(dev, "failed to get free message slot (%ld)\n",
			PTR_ERR(xfer));
		scmi_clear_channel(info, cinfo);
		return;
	}

	unpack_scmi_header(msg_hdr, &xfer->hdr);
	if (priv)
		/* Ensure order between xfer->priv store and following ops */
		smp_store_mb(xfer->priv, priv);
	info->desc->ops->fetch_notification(cinfo, info->desc->max_msg_size,
					    xfer);

	trace_scmi_msg_dump(xfer->hdr.protocol_id, xfer->hdr.id, "NOTI",
			    xfer->hdr.seq, xfer->hdr.status,
			    xfer->rx.buf, xfer->rx.len);

	scmi_notify(cinfo->handle, xfer->hdr.protocol_id,
		    xfer->hdr.id, xfer->rx.buf, xfer->rx.len, ts);

	trace_scmi_rx_done(xfer->transfer_id, xfer->hdr.id,
			   xfer->hdr.protocol_id, xfer->hdr.seq,
			   MSG_TYPE_NOTIFICATION);

	__scmi_xfer_put(minfo, xfer);

	scmi_clear_channel(info, cinfo);
}

static void scmi_handle_response(struct scmi_chan_info *cinfo,
				 u32 msg_hdr, void *priv)
{
	struct scmi_xfer *xfer;
	struct scmi_info *info = handle_to_scmi_info(cinfo->handle);

	xfer = scmi_xfer_command_acquire(cinfo, msg_hdr);
	if (IS_ERR(xfer)) {
		if (MSG_XTRACT_TYPE(msg_hdr) == MSG_TYPE_DELAYED_RESP)
			scmi_clear_channel(info, cinfo);
		return;
	}

	/* rx.len could be shrunk in the sync do_xfer, so reset to maxsz */
	if (xfer->hdr.type == MSG_TYPE_DELAYED_RESP)
		xfer->rx.len = info->desc->max_msg_size;

	if (priv)
		/* Ensure order between xfer->priv store and following ops */
		smp_store_mb(xfer->priv, priv);
	info->desc->ops->fetch_response(cinfo, xfer);

	trace_scmi_msg_dump(xfer->hdr.protocol_id, xfer->hdr.id,
			    xfer->hdr.type == MSG_TYPE_DELAYED_RESP ?
			    "DLYD" : "RESP",
			    xfer->hdr.seq, xfer->hdr.status,
			    xfer->rx.buf, xfer->rx.len);

	trace_scmi_rx_done(xfer->transfer_id, xfer->hdr.id,
			   xfer->hdr.protocol_id, xfer->hdr.seq,
			   xfer->hdr.type);

	if (xfer->hdr.type == MSG_TYPE_DELAYED_RESP) {
		scmi_clear_channel(info, cinfo);
		complete(xfer->async_done);
	} else {
		complete(&xfer->done);
	}

	scmi_xfer_command_release(info, xfer);
}

/**
 * scmi_rx_callback() - callback for receiving messages
 *
 * @cinfo: SCMI channel info
 * @msg_hdr: Message header
 * @priv: Transport specific private data.
 *
 * Processes one received message to appropriate transfer information and
 * signals completion of the transfer.
 *
 * NOTE: This function will be invoked in IRQ context, hence should be
 * as optimal as possible.
 */
void scmi_rx_callback(struct scmi_chan_info *cinfo, u32 msg_hdr, void *priv)
{
	u8 msg_type = MSG_XTRACT_TYPE(msg_hdr);

	switch (msg_type) {
	case MSG_TYPE_NOTIFICATION:
		scmi_handle_notification(cinfo, msg_hdr, priv);
		break;
	case MSG_TYPE_COMMAND:
	case MSG_TYPE_DELAYED_RESP:
		scmi_handle_response(cinfo, msg_hdr, priv);
		break;
	default:
		WARN_ONCE(1, "received unknown msg_type:%d\n", msg_type);
		break;
	}
}

/**
 * xfer_put() - Release a transmit message
 *
 * @ph: Pointer to SCMI protocol handle
 * @xfer: message that was reserved by xfer_get_init
 */
static void xfer_put(const struct scmi_protocol_handle *ph,
		     struct scmi_xfer *xfer)
{
	const struct scmi_protocol_instance *pi = ph_to_pi(ph);
	struct scmi_info *info = handle_to_scmi_info(pi->handle);

	__scmi_xfer_put(&info->tx_minfo, xfer);
}

static bool scmi_xfer_done_no_timeout(struct scmi_chan_info *cinfo,
				      struct scmi_xfer *xfer, ktime_t stop)
{
	struct scmi_info *info = handle_to_scmi_info(cinfo->handle);

	/*
	 * Poll also on xfer->done so that polling can be forcibly terminated
	 * in case of out-of-order receptions of delayed responses
	 */
	return info->desc->ops->poll_done(cinfo, xfer) ||
	       try_wait_for_completion(&xfer->done) ||
	       ktime_after(ktime_get(), stop);
}

/**
 * scmi_wait_for_message_response  - An helper to group all the possible ways of
 * waiting for a synchronous message response.
 *
 * @cinfo: SCMI channel info
 * @xfer: Reference to the transfer being waited for.
 *
 * Chooses waiting strategy (sleep-waiting vs busy-waiting) depending on
 * configuration flags like xfer->hdr.poll_completion.
 *
 * Return: 0 on Success, error otherwise.
 */
static int scmi_wait_for_message_response(struct scmi_chan_info *cinfo,
					  struct scmi_xfer *xfer)
{
	struct scmi_info *info = handle_to_scmi_info(cinfo->handle);
	struct device *dev = info->dev;
	int ret = 0, timeout_ms = info->desc->max_rx_timeout_ms;

	trace_scmi_xfer_response_wait(xfer->transfer_id, xfer->hdr.id,
				      xfer->hdr.protocol_id, xfer->hdr.seq,
				      timeout_ms,
				      xfer->hdr.poll_completion);

	if (xfer->hdr.poll_completion) {
		/*
		 * Real polling is needed only if transport has NOT declared
		 * itself to support synchronous commands replies.
		 */
		if (!info->desc->sync_cmds_completed_on_ret) {
			/*
			 * Poll on xfer using transport provided .poll_done();
			 * assumes no completion interrupt was available.
			 */
			ktime_t stop = ktime_add_ms(ktime_get(), timeout_ms);

			spin_until_cond(scmi_xfer_done_no_timeout(cinfo,
								  xfer, stop));
			if (ktime_after(ktime_get(), stop)) {
				dev_err(dev,
					"timed out in resp(caller: %pS) - polling\n",
					(void *)_RET_IP_);
				ret = -ETIMEDOUT;
			}
		}

		if (!ret) {
			unsigned long flags;

			/*
			 * Do not fetch_response if an out-of-order delayed
			 * response is being processed.
			 */
			spin_lock_irqsave(&xfer->lock, flags);
			if (xfer->state == SCMI_XFER_SENT_OK) {
				info->desc->ops->fetch_response(cinfo, xfer);
				xfer->state = SCMI_XFER_RESP_OK;
			}
			spin_unlock_irqrestore(&xfer->lock, flags);

			/* Trace polled replies. */
			trace_scmi_msg_dump(xfer->hdr.protocol_id, xfer->hdr.id,
					    "RESP",
					    xfer->hdr.seq, xfer->hdr.status,
					    xfer->rx.buf, xfer->rx.len);
		}
	} else {
		/* And we wait for the response. */
		if (!wait_for_completion_timeout(&xfer->done,
						 msecs_to_jiffies(timeout_ms))) {
			dev_err(dev, "timed out in resp(caller: %pS)\n",
				(void *)_RET_IP_);
			ret = -ETIMEDOUT;
		}
	}

	return ret;
}

/**
 * do_xfer() - Do one transfer
 *
 * @ph: Pointer to SCMI protocol handle
 * @xfer: Transfer to initiate and wait for response
 *
 * Return: -ETIMEDOUT in case of no response, if transmit error,
 *	return corresponding error, else if all goes well,
 *	return 0.
 */
static int do_xfer(const struct scmi_protocol_handle *ph,
		   struct scmi_xfer *xfer)
{
	int ret;
	const struct scmi_protocol_instance *pi = ph_to_pi(ph);
	struct scmi_info *info = handle_to_scmi_info(pi->handle);
	struct device *dev = info->dev;
	struct scmi_chan_info *cinfo;

	/* Check for polling request on custom command xfers at first */
	if (xfer->hdr.poll_completion && !is_transport_polling_capable(info)) {
		dev_warn_once(dev,
			      "Polling mode is not supported by transport.\n");
		return -EINVAL;
	}

	cinfo = idr_find(&info->tx_idr, pi->proto->id);
	if (unlikely(!cinfo))
		return -EINVAL;

	/* True ONLY if also supported by transport. */
	if (is_polling_enabled(cinfo, info))
		xfer->hdr.poll_completion = true;

	/*
	 * Initialise protocol id now from protocol handle to avoid it being
	 * overridden by mistake (or malice) by the protocol code mangling with
	 * the scmi_xfer structure prior to this.
	 */
	xfer->hdr.protocol_id = pi->proto->id;
	reinit_completion(&xfer->done);

	trace_scmi_xfer_begin(xfer->transfer_id, xfer->hdr.id,
			      xfer->hdr.protocol_id, xfer->hdr.seq,
			      xfer->hdr.poll_completion);

	xfer->state = SCMI_XFER_SENT_OK;
	/*
	 * Even though spinlocking is not needed here since no race is possible
	 * on xfer->state due to the monotonically increasing tokens allocation,
	 * we must anyway ensure xfer->state initialization is not re-ordered
	 * after the .send_message() to be sure that on the RX path an early
	 * ISR calling scmi_rx_callback() cannot see an old stale xfer->state.
	 */
	smp_mb();

	ret = info->desc->ops->send_message(cinfo, xfer);
	if (ret < 0) {
		dev_dbg(dev, "Failed to send message %d\n", ret);
		return ret;
	}

	trace_scmi_msg_dump(xfer->hdr.protocol_id, xfer->hdr.id, "CMND",
			    xfer->hdr.seq, xfer->hdr.status,
			    xfer->tx.buf, xfer->tx.len);

	ret = scmi_wait_for_message_response(cinfo, xfer);
	if (!ret && xfer->hdr.status)
		ret = scmi_to_linux_errno(xfer->hdr.status);

	if (info->desc->ops->mark_txdone)
		info->desc->ops->mark_txdone(cinfo, ret, xfer);

	trace_scmi_xfer_end(xfer->transfer_id, xfer->hdr.id,
			    xfer->hdr.protocol_id, xfer->hdr.seq, ret);

	return ret;
}

static void reset_rx_to_maxsz(const struct scmi_protocol_handle *ph,
			      struct scmi_xfer *xfer)
{
	const struct scmi_protocol_instance *pi = ph_to_pi(ph);
	struct scmi_info *info = handle_to_scmi_info(pi->handle);

	xfer->rx.len = info->desc->max_msg_size;
}

#define SCMI_MAX_RESPONSE_TIMEOUT	(2 * MSEC_PER_SEC)

/**
 * do_xfer_with_response() - Do one transfer and wait until the delayed
 *	response is received
 *
 * @ph: Pointer to SCMI protocol handle
 * @xfer: Transfer to initiate and wait for response
 *
 * Using asynchronous commands in atomic/polling mode should be avoided since
 * it could cause long busy-waiting here, so ignore polling for the delayed
 * response and WARN if it was requested for this command transaction since
 * upper layers should refrain from issuing such kind of requests.
 *
 * The only other option would have been to refrain from using any asynchronous
 * command even if made available, when an atomic transport is detected, and
 * instead forcibly use the synchronous version (thing that can be easily
 * attained at the protocol layer), but this would also have led to longer
 * stalls of the channel for synchronous commands and possibly timeouts.
 * (in other words there is usually a good reason if a platform provides an
 *  asynchronous version of a command and we should prefer to use it...just not
 *  when using atomic/polling mode)
 *
 * Return: -ETIMEDOUT in case of no delayed response, if transmit error,
 *	return corresponding error, else if all goes well, return 0.
 */
static int do_xfer_with_response(const struct scmi_protocol_handle *ph,
				 struct scmi_xfer *xfer)
{
	int ret, timeout = msecs_to_jiffies(SCMI_MAX_RESPONSE_TIMEOUT);
	DECLARE_COMPLETION_ONSTACK(async_response);

	xfer->async_done = &async_response;

	/*
	 * Delayed responses should not be polled, so an async command should
	 * not have been used when requiring an atomic/poll context; WARN and
	 * perform instead a sleeping wait.
	 * (Note Async + IgnoreDelayedResponses are sent via do_xfer)
	 */
	WARN_ON_ONCE(xfer->hdr.poll_completion);

	ret = do_xfer(ph, xfer);
	if (!ret) {
		if (!wait_for_completion_timeout(xfer->async_done, timeout)) {
			dev_err(ph->dev,
				"timed out in delayed resp(caller: %pS)\n",
				(void *)_RET_IP_);
			ret = -ETIMEDOUT;
		} else if (xfer->hdr.status) {
			ret = scmi_to_linux_errno(xfer->hdr.status);
		}
	}

	xfer->async_done = NULL;
	return ret;
}

/**
 * xfer_get_init() - Allocate and initialise one message for transmit
 *
 * @ph: Pointer to SCMI protocol handle
 * @msg_id: Message identifier
 * @tx_size: transmit message size
 * @rx_size: receive message size
 * @p: pointer to the allocated and initialised message
 *
 * This function allocates the message using @scmi_xfer_get and
 * initialise the header.
 *
 * Return: 0 if all went fine with @p pointing to message, else
 *	corresponding error.
 */
static int xfer_get_init(const struct scmi_protocol_handle *ph,
			 u8 msg_id, size_t tx_size, size_t rx_size,
			 struct scmi_xfer **p)
{
	int ret;
	struct scmi_xfer *xfer;
	const struct scmi_protocol_instance *pi = ph_to_pi(ph);
	struct scmi_info *info = handle_to_scmi_info(pi->handle);
	struct scmi_xfers_info *minfo = &info->tx_minfo;
	struct device *dev = info->dev;

	/* Ensure we have sane transfer sizes */
	if (rx_size > info->desc->max_msg_size ||
	    tx_size > info->desc->max_msg_size)
		return -ERANGE;

	xfer = scmi_xfer_get(pi->handle, minfo, true);
	if (IS_ERR(xfer)) {
		ret = PTR_ERR(xfer);
		dev_err(dev, "failed to get free message slot(%d)\n", ret);
		return ret;
	}

	xfer->tx.len = tx_size;
	xfer->rx.len = rx_size ? : info->desc->max_msg_size;
	xfer->hdr.type = MSG_TYPE_COMMAND;
	xfer->hdr.id = msg_id;
	xfer->hdr.poll_completion = false;

	*p = xfer;

	return 0;
}

/**
 * version_get() - command to get the revision of the SCMI entity
 *
 * @ph: Pointer to SCMI protocol handle
 * @version: Holds returned version of protocol.
 *
 * Updates the SCMI information in the internal data structure.
 *
 * Return: 0 if all went fine, else return appropriate error.
 */
static int version_get(const struct scmi_protocol_handle *ph, u32 *version)
{
	int ret;
	__le32 *rev_info;
	struct scmi_xfer *t;

	ret = xfer_get_init(ph, PROTOCOL_VERSION, 0, sizeof(*version), &t);
	if (ret)
		return ret;

	ret = do_xfer(ph, t);
	if (!ret) {
		rev_info = t->rx.buf;
		*version = le32_to_cpu(*rev_info);
	}

	xfer_put(ph, t);
	return ret;
}

/**
 * scmi_set_protocol_priv  - Set protocol specific data at init time
 *
 * @ph: A reference to the protocol handle.
 * @priv: The private data to set.
 *
 * Return: 0 on Success
 */
static int scmi_set_protocol_priv(const struct scmi_protocol_handle *ph,
				  void *priv)
{
	struct scmi_protocol_instance *pi = ph_to_pi(ph);

	pi->priv = priv;

	return 0;
}

/**
 * scmi_get_protocol_priv  - Set protocol specific data at init time
 *
 * @ph: A reference to the protocol handle.
 *
 * Return: Protocol private data if any was set.
 */
static void *scmi_get_protocol_priv(const struct scmi_protocol_handle *ph)
{
	const struct scmi_protocol_instance *pi = ph_to_pi(ph);

	return pi->priv;
}

static const struct scmi_xfer_ops xfer_ops = {
	.version_get = version_get,
	.xfer_get_init = xfer_get_init,
	.reset_rx_to_maxsz = reset_rx_to_maxsz,
	.do_xfer = do_xfer,
	.do_xfer_with_response = do_xfer_with_response,
	.xfer_put = xfer_put,
};

struct scmi_msg_resp_domain_name_get {
	__le32 flags;
	u8 name[SCMI_MAX_STR_SIZE];
};

/**
 * scmi_common_extended_name_get  - Common helper to get extended resources name
 * @ph: A protocol handle reference.
 * @cmd_id: The specific command ID to use.
 * @res_id: The specific resource ID to use.
 * @name: A pointer to the preallocated area where the retrieved name will be
 *	  stored as a NULL terminated string.
 * @len: The len in bytes of the @name char array.
 *
 * Return: 0 on Succcess
 */
static int scmi_common_extended_name_get(const struct scmi_protocol_handle *ph,
					 u8 cmd_id, u32 res_id, char *name,
					 size_t len)
{
	int ret;
	struct scmi_xfer *t;
	struct scmi_msg_resp_domain_name_get *resp;

	ret = ph->xops->xfer_get_init(ph, cmd_id, sizeof(res_id),
				      sizeof(*resp), &t);
	if (ret)
		goto out;

	put_unaligned_le32(res_id, t->tx.buf);
	resp = t->rx.buf;

	ret = ph->xops->do_xfer(ph, t);
	if (!ret)
		strscpy(name, resp->name, len);

	ph->xops->xfer_put(ph, t);
out:
	if (ret)
		dev_warn(ph->dev,
			 "Failed to get extended name - id:%u (ret:%d). Using %s\n",
			 res_id, ret, name);
	return ret;
}

/**
 * struct scmi_iterator  - Iterator descriptor
 * @msg: A reference to the message TX buffer; filled by @prepare_message with
 *	 a proper custom command payload for each multi-part command request.
 * @resp: A reference to the response RX buffer; used by @update_state and
 *	  @process_response to parse the multi-part replies.
 * @t: A reference to the underlying xfer initialized and used transparently by
 *     the iterator internal routines.
 * @ph: A reference to the associated protocol handle to be used.
 * @ops: A reference to the custom provided iterator operations.
 * @state: The current iterator state; used and updated in turn by the iterators
 *	   internal routines and by the caller-provided @scmi_iterator_ops.
 * @priv: A reference to optional private data as provided by the caller and
 *	  passed back to the @@scmi_iterator_ops.
 */
struct scmi_iterator {
	void *msg;
	void *resp;
	struct scmi_xfer *t;
	const struct scmi_protocol_handle *ph;
	struct scmi_iterator_ops *ops;
	struct scmi_iterator_state state;
	void *priv;
};

static void *scmi_iterator_init(const struct scmi_protocol_handle *ph,
				struct scmi_iterator_ops *ops,
				unsigned int max_resources, u8 msg_id,
				size_t tx_size, void *priv)
{
	int ret;
	struct scmi_iterator *i;

	i = devm_kzalloc(ph->dev, sizeof(*i), GFP_KERNEL);
	if (!i)
		return ERR_PTR(-ENOMEM);

	i->ph = ph;
	i->ops = ops;
	i->priv = priv;

	ret = ph->xops->xfer_get_init(ph, msg_id, tx_size, 0, &i->t);
	if (ret) {
		devm_kfree(ph->dev, i);
		return ERR_PTR(ret);
	}

	i->state.max_resources = max_resources;
	i->msg = i->t->tx.buf;
	i->resp = i->t->rx.buf;

	return i;
}

static int scmi_iterator_run(void *iter)
{
	int ret = -EINVAL;
	struct scmi_iterator_ops *iops;
	const struct scmi_protocol_handle *ph;
	struct scmi_iterator_state *st;
	struct scmi_iterator *i = iter;

	if (!i || !i->ops || !i->ph)
		return ret;

	iops = i->ops;
	ph = i->ph;
	st = &i->state;

	do {
		iops->prepare_message(i->msg, st->desc_index, i->priv);
		ret = ph->xops->do_xfer(ph, i->t);
		if (ret)
			break;

		st->rx_len = i->t->rx.len;
		ret = iops->update_state(st, i->resp, i->priv);
		if (ret)
			break;

		if (st->num_returned > st->max_resources - st->desc_index) {
			dev_err(ph->dev,
				"No. of resources can't exceed %d\n",
				st->max_resources);
			ret = -EINVAL;
			break;
		}

		for (st->loop_idx = 0; st->loop_idx < st->num_returned;
		     st->loop_idx++) {
			ret = iops->process_response(ph, i->resp, st, i->priv);
			if (ret)
				goto out;
		}

		st->desc_index += st->num_returned;
		ph->xops->reset_rx_to_maxsz(ph, i->t);
		/*
		 * check for both returned and remaining to avoid infinite
		 * loop due to buggy firmware
		 */
	} while (st->num_returned && st->num_remaining);

out:
	/* Finalize and destroy iterator */
	ph->xops->xfer_put(ph, i->t);
	devm_kfree(ph->dev, i);

	return ret;
}

struct scmi_msg_get_fc_info {
	__le32 domain;
	__le32 message_id;
};

struct scmi_msg_resp_desc_fc {
	__le32 attr;
#define SUPPORTS_DOORBELL(x)		((x) & BIT(0))
#define DOORBELL_REG_WIDTH(x)		FIELD_GET(GENMASK(2, 1), (x))
	__le32 rate_limit;
	__le32 chan_addr_low;
	__le32 chan_addr_high;
	__le32 chan_size;
	__le32 db_addr_low;
	__le32 db_addr_high;
	__le32 db_set_lmask;
	__le32 db_set_hmask;
	__le32 db_preserve_lmask;
	__le32 db_preserve_hmask;
};

static void
scmi_common_fastchannel_init(const struct scmi_protocol_handle *ph,
			     u8 describe_id, u32 message_id, u32 valid_size,
			     u32 domain, void __iomem **p_addr,
			     struct scmi_fc_db_info **p_db)
{
	int ret;
	u32 flags;
	u64 phys_addr;
	u8 size;
	void __iomem *addr;
	struct scmi_xfer *t;
	struct scmi_fc_db_info *db = NULL;
	struct scmi_msg_get_fc_info *info;
	struct scmi_msg_resp_desc_fc *resp;
	const struct scmi_protocol_instance *pi = ph_to_pi(ph);

	if (!p_addr) {
		ret = -EINVAL;
		goto err_out;
	}

	ret = ph->xops->xfer_get_init(ph, describe_id,
				      sizeof(*info), sizeof(*resp), &t);
	if (ret)
		goto err_out;

	info = t->tx.buf;
	info->domain = cpu_to_le32(domain);
	info->message_id = cpu_to_le32(message_id);

	/*
	 * Bail out on error leaving fc_info addresses zeroed; this includes
	 * the case in which the requested domain/message_id does NOT support
	 * fastchannels at all.
	 */
	ret = ph->xops->do_xfer(ph, t);
	if (ret)
		goto err_xfer;

	resp = t->rx.buf;
	flags = le32_to_cpu(resp->attr);
	size = le32_to_cpu(resp->chan_size);
	if (size != valid_size) {
		ret = -EINVAL;
		goto err_xfer;
	}

	phys_addr = le32_to_cpu(resp->chan_addr_low);
	phys_addr |= (u64)le32_to_cpu(resp->chan_addr_high) << 32;
	addr = devm_ioremap(ph->dev, phys_addr, size);
	if (!addr) {
		ret = -EADDRNOTAVAIL;
		goto err_xfer;
	}

	*p_addr = addr;

	if (p_db && SUPPORTS_DOORBELL(flags)) {
		db = devm_kzalloc(ph->dev, sizeof(*db), GFP_KERNEL);
		if (!db) {
			ret = -ENOMEM;
			goto err_db;
		}

		size = 1 << DOORBELL_REG_WIDTH(flags);
		phys_addr = le32_to_cpu(resp->db_addr_low);
		phys_addr |= (u64)le32_to_cpu(resp->db_addr_high) << 32;
		addr = devm_ioremap(ph->dev, phys_addr, size);
		if (!addr) {
			ret = -EADDRNOTAVAIL;
			goto err_db_mem;
		}

		db->addr = addr;
		db->width = size;
		db->set = le32_to_cpu(resp->db_set_lmask);
		db->set |= (u64)le32_to_cpu(resp->db_set_hmask) << 32;
		db->mask = le32_to_cpu(resp->db_preserve_lmask);
		db->mask |= (u64)le32_to_cpu(resp->db_preserve_hmask) << 32;

		*p_db = db;
	}

	ph->xops->xfer_put(ph, t);

	dev_dbg(ph->dev,
		"Using valid FC for protocol %X [MSG_ID:%u / RES_ID:%u]\n",
		pi->proto->id, message_id, domain);

	return;

err_db_mem:
	devm_kfree(ph->dev, db);

err_db:
	*p_addr = NULL;

err_xfer:
	ph->xops->xfer_put(ph, t);

err_out:
	dev_warn(ph->dev,
		 "Failed to get FC for protocol %X [MSG_ID:%u / RES_ID:%u] - ret:%d. Using regular messaging.\n",
		 pi->proto->id, message_id, domain, ret);
}

#define SCMI_PROTO_FC_RING_DB(w)			\
do {							\
	u##w val = 0;					\
							\
	if (db->mask)					\
		val = ioread##w(db->addr) & db->mask;	\
	iowrite##w((u##w)db->set | val, db->addr);	\
} while (0)

static void scmi_common_fastchannel_db_ring(struct scmi_fc_db_info *db)
{
	if (!db || !db->addr)
		return;

	if (db->width == 1)
		SCMI_PROTO_FC_RING_DB(8);
	else if (db->width == 2)
		SCMI_PROTO_FC_RING_DB(16);
	else if (db->width == 4)
		SCMI_PROTO_FC_RING_DB(32);
	else /* db->width == 8 */
#ifdef CONFIG_64BIT
		SCMI_PROTO_FC_RING_DB(64);
#else
	{
		u64 val = 0;

		if (db->mask)
			val = ioread64_hi_lo(db->addr) & db->mask;
		iowrite64_hi_lo(db->set | val, db->addr);
	}
#endif
}

static const struct scmi_proto_helpers_ops helpers_ops = {
	.extended_name_get = scmi_common_extended_name_get,
	.iter_response_init = scmi_iterator_init,
	.iter_response_run = scmi_iterator_run,
	.fastchannel_init = scmi_common_fastchannel_init,
	.fastchannel_db_ring = scmi_common_fastchannel_db_ring,
};

/**
 * scmi_revision_area_get  - Retrieve version memory area.
 *
 * @ph: A reference to the protocol handle.
 *
 * A helper to grab the version memory area reference during SCMI Base protocol
 * initialization.
 *
 * Return: A reference to the version memory area associated to the SCMI
 *	   instance underlying this protocol handle.
 */
struct scmi_revision_info *
scmi_revision_area_get(const struct scmi_protocol_handle *ph)
{
	const struct scmi_protocol_instance *pi = ph_to_pi(ph);

	return pi->handle->version;
}

/**
 * scmi_alloc_init_protocol_instance  - Allocate and initialize a protocol
 * instance descriptor.
 * @info: The reference to the related SCMI instance.
 * @proto: The protocol descriptor.
 *
 * Allocate a new protocol instance descriptor, using the provided @proto
 * description, against the specified SCMI instance @info, and initialize it;
 * all resources management is handled via a dedicated per-protocol devres
 * group.
 *
 * Context: Assumes to be called with @protocols_mtx already acquired.
 * Return: A reference to a freshly allocated and initialized protocol instance
 *	   or ERR_PTR on failure. On failure the @proto reference is at first
 *	   put using @scmi_protocol_put() before releasing all the devres group.
 */
static struct scmi_protocol_instance *
scmi_alloc_init_protocol_instance(struct scmi_info *info,
				  const struct scmi_protocol *proto)
{
	int ret = -ENOMEM;
	void *gid;
	struct scmi_protocol_instance *pi;
	const struct scmi_handle *handle = &info->handle;

	/* Protocol specific devres group */
	gid = devres_open_group(handle->dev, NULL, GFP_KERNEL);
	if (!gid) {
		scmi_protocol_put(proto->id);
		goto out;
	}

	pi = devm_kzalloc(handle->dev, sizeof(*pi), GFP_KERNEL);
	if (!pi)
		goto clean;

	pi->gid = gid;
	pi->proto = proto;
	pi->handle = handle;
	pi->ph.dev = handle->dev;
	pi->ph.xops = &xfer_ops;
	pi->ph.hops = &helpers_ops;
	pi->ph.set_priv = scmi_set_protocol_priv;
	pi->ph.get_priv = scmi_get_protocol_priv;
	refcount_set(&pi->users, 1);
	/* proto->init is assured NON NULL by scmi_protocol_register */
	ret = pi->proto->instance_init(&pi->ph);
	if (ret)
		goto clean;

	ret = idr_alloc(&info->protocols, pi, proto->id, proto->id + 1,
			GFP_KERNEL);
	if (ret != proto->id)
		goto clean;

	/*
	 * Warn but ignore events registration errors since we do not want
	 * to skip whole protocols if their notifications are messed up.
	 */
	if (pi->proto->events) {
		ret = scmi_register_protocol_events(handle, pi->proto->id,
						    &pi->ph,
						    pi->proto->events);
		if (ret)
			dev_warn(handle->dev,
				 "Protocol:%X - Events Registration Failed - err:%d\n",
				 pi->proto->id, ret);
	}

	devres_close_group(handle->dev, pi->gid);
	dev_dbg(handle->dev, "Initialized protocol: 0x%X\n", pi->proto->id);

	return pi;

clean:
	/* Take care to put the protocol module's owner before releasing all */
	scmi_protocol_put(proto->id);
	devres_release_group(handle->dev, gid);
out:
	return ERR_PTR(ret);
}

/**
 * scmi_get_protocol_instance  - Protocol initialization helper.
 * @handle: A reference to the SCMI platform instance.
 * @protocol_id: The protocol being requested.
 *
 * In case the required protocol has never been requested before for this
 * instance, allocate and initialize all the needed structures while handling
 * resource allocation with a dedicated per-protocol devres subgroup.
 *
 * Return: A reference to an initialized protocol instance or error on failure:
 *	   in particular returns -EPROBE_DEFER when the desired protocol could
 *	   NOT be found.
 */
static struct scmi_protocol_instance * __must_check
scmi_get_protocol_instance(const struct scmi_handle *handle, u8 protocol_id)
{
	struct scmi_protocol_instance *pi;
	struct scmi_info *info = handle_to_scmi_info(handle);

	mutex_lock(&info->protocols_mtx);
	pi = idr_find(&info->protocols, protocol_id);

	if (pi) {
		refcount_inc(&pi->users);
	} else {
		const struct scmi_protocol *proto;

		/* Fails if protocol not registered on bus */
		proto = scmi_protocol_get(protocol_id);
		if (proto)
			pi = scmi_alloc_init_protocol_instance(info, proto);
		else
			pi = ERR_PTR(-EPROBE_DEFER);
	}
	mutex_unlock(&info->protocols_mtx);

	return pi;
}

/**
 * scmi_protocol_acquire  - Protocol acquire
 * @handle: A reference to the SCMI platform instance.
 * @protocol_id: The protocol being requested.
 *
 * Register a new user for the requested protocol on the specified SCMI
 * platform instance, possibly triggering its initialization on first user.
 *
 * Return: 0 if protocol was acquired successfully.
 */
int scmi_protocol_acquire(const struct scmi_handle *handle, u8 protocol_id)
{
	return PTR_ERR_OR_ZERO(scmi_get_protocol_instance(handle, protocol_id));
}

/**
 * scmi_protocol_release  - Protocol de-initialization helper.
 * @handle: A reference to the SCMI platform instance.
 * @protocol_id: The protocol being requested.
 *
 * Remove one user for the specified protocol and triggers de-initialization
 * and resources de-allocation once the last user has gone.
 */
void scmi_protocol_release(const struct scmi_handle *handle, u8 protocol_id)
{
	struct scmi_info *info = handle_to_scmi_info(handle);
	struct scmi_protocol_instance *pi;

	mutex_lock(&info->protocols_mtx);
	pi = idr_find(&info->protocols, protocol_id);
	if (WARN_ON(!pi))
		goto out;

	if (refcount_dec_and_test(&pi->users)) {
		void *gid = pi->gid;

		if (pi->proto->events)
			scmi_deregister_protocol_events(handle, protocol_id);

		if (pi->proto->instance_deinit)
			pi->proto->instance_deinit(&pi->ph);

		idr_remove(&info->protocols, protocol_id);

		scmi_protocol_put(protocol_id);

		devres_release_group(handle->dev, gid);
		dev_dbg(handle->dev, "De-Initialized protocol: 0x%X\n",
			protocol_id);
	}

out:
	mutex_unlock(&info->protocols_mtx);
}

void scmi_setup_protocol_implemented(const struct scmi_protocol_handle *ph,
				     u8 *prot_imp)
{
	const struct scmi_protocol_instance *pi = ph_to_pi(ph);
	struct scmi_info *info = handle_to_scmi_info(pi->handle);

	info->protocols_imp = prot_imp;
}

static bool
scmi_is_protocol_implemented(const struct scmi_handle *handle, u8 prot_id)
{
	int i;
	struct scmi_info *info = handle_to_scmi_info(handle);
	struct scmi_revision_info *rev = handle->version;

	if (!info->protocols_imp)
		return false;

	for (i = 0; i < rev->num_protocols; i++)
		if (info->protocols_imp[i] == prot_id)
			return true;
	return false;
}

struct scmi_protocol_devres {
	const struct scmi_handle *handle;
	u8 protocol_id;
};

static void scmi_devm_release_protocol(struct device *dev, void *res)
{
	struct scmi_protocol_devres *dres = res;

	scmi_protocol_release(dres->handle, dres->protocol_id);
}

static struct scmi_protocol_instance __must_check *
scmi_devres_protocol_instance_get(struct scmi_device *sdev, u8 protocol_id)
{
	struct scmi_protocol_instance *pi;
	struct scmi_protocol_devres *dres;

	dres = devres_alloc(scmi_devm_release_protocol,
			    sizeof(*dres), GFP_KERNEL);
	if (!dres)
		return ERR_PTR(-ENOMEM);

	pi = scmi_get_protocol_instance(sdev->handle, protocol_id);
	if (IS_ERR(pi)) {
		devres_free(dres);
		return pi;
	}

	dres->handle = sdev->handle;
	dres->protocol_id = protocol_id;
	devres_add(&sdev->dev, dres);

	return pi;
}

/**
 * scmi_devm_protocol_get  - Devres managed get protocol operations and handle
 * @sdev: A reference to an scmi_device whose embedded struct device is to
 *	  be used for devres accounting.
 * @protocol_id: The protocol being requested.
 * @ph: A pointer reference used to pass back the associated protocol handle.
 *
 * Get hold of a protocol accounting for its usage, eventually triggering its
 * initialization, and returning the protocol specific operations and related
 * protocol handle which will be used as first argument in most of the
 * protocols operations methods.
 * Being a devres based managed method, protocol hold will be automatically
 * released, and possibly de-initialized on last user, once the SCMI driver
 * owning the scmi_device is unbound from it.
 *
 * Return: A reference to the requested protocol operations or error.
 *	   Must be checked for errors by caller.
 */
static const void __must_check *
scmi_devm_protocol_get(struct scmi_device *sdev, u8 protocol_id,
		       struct scmi_protocol_handle **ph)
{
	struct scmi_protocol_instance *pi;

	if (!ph)
		return ERR_PTR(-EINVAL);

	pi = scmi_devres_protocol_instance_get(sdev, protocol_id);
	if (IS_ERR(pi))
		return pi;

	*ph = &pi->ph;

	return pi->proto->ops;
}

/**
 * scmi_devm_protocol_acquire  - Devres managed helper to get hold of a protocol
 * @sdev: A reference to an scmi_device whose embedded struct device is to
 *	  be used for devres accounting.
 * @protocol_id: The protocol being requested.
 *
 * Get hold of a protocol accounting for its usage, possibly triggering its
 * initialization but without getting access to its protocol specific operations
 * and handle.
 *
 * Being a devres based managed method, protocol hold will be automatically
 * released, and possibly de-initialized on last user, once the SCMI driver
 * owning the scmi_device is unbound from it.
 *
 * Return: 0 on SUCCESS
 */
static int __must_check scmi_devm_protocol_acquire(struct scmi_device *sdev,
						   u8 protocol_id)
{
	struct scmi_protocol_instance *pi;

	pi = scmi_devres_protocol_instance_get(sdev, protocol_id);
	if (IS_ERR(pi))
		return PTR_ERR(pi);

	return 0;
}

static int scmi_devm_protocol_match(struct device *dev, void *res, void *data)
{
	struct scmi_protocol_devres *dres = res;

	if (WARN_ON(!dres || !data))
		return 0;

	return dres->protocol_id == *((u8 *)data);
}

/**
 * scmi_devm_protocol_put  - Devres managed put protocol operations and handle
 * @sdev: A reference to an scmi_device whose embedded struct device is to
 *	  be used for devres accounting.
 * @protocol_id: The protocol being requested.
 *
 * Explicitly release a protocol hold previously obtained calling the above
 * @scmi_devm_protocol_get.
 */
static void scmi_devm_protocol_put(struct scmi_device *sdev, u8 protocol_id)
{
	int ret;

	ret = devres_release(&sdev->dev, scmi_devm_release_protocol,
			     scmi_devm_protocol_match, &protocol_id);
	WARN_ON(ret);
}

/**
 * scmi_is_transport_atomic  - Method to check if underlying transport for an
 * SCMI instance is configured as atomic.
 *
 * @handle: A reference to the SCMI platform instance.
 * @atomic_threshold: An optional return value for the system wide currently
 *		      configured threshold for atomic operations.
 *
 * Return: True if transport is configured as atomic
 */
static bool scmi_is_transport_atomic(const struct scmi_handle *handle,
				     unsigned int *atomic_threshold)
{
	bool ret;
	struct scmi_info *info = handle_to_scmi_info(handle);

	ret = info->desc->atomic_enabled && is_transport_polling_capable(info);
	if (ret && atomic_threshold)
		*atomic_threshold = info->atomic_threshold;

	return ret;
}

static inline
struct scmi_handle *scmi_handle_get_from_info_unlocked(struct scmi_info *info)
{
	info->users++;
	return &info->handle;
}

/**
 * scmi_handle_get() - Get the SCMI handle for a device
 *
 * @dev: pointer to device for which we want SCMI handle
 *
 * NOTE: The function does not track individual clients of the framework
 * and is expected to be maintained by caller of SCMI protocol library.
 * scmi_handle_put must be balanced with successful scmi_handle_get
 *
 * Return: pointer to handle if successful, NULL on error
 */
struct scmi_handle *scmi_handle_get(struct device *dev)
{
	struct list_head *p;
	struct scmi_info *info;
	struct scmi_handle *handle = NULL;

	mutex_lock(&scmi_list_mutex);
	list_for_each(p, &scmi_list) {
		info = list_entry(p, struct scmi_info, node);
		if (dev->parent == info->dev) {
			handle = scmi_handle_get_from_info_unlocked(info);
			break;
		}
	}
	mutex_unlock(&scmi_list_mutex);

	return handle;
}

/**
 * scmi_handle_put() - Release the handle acquired by scmi_handle_get
 *
 * @handle: handle acquired by scmi_handle_get
 *
 * NOTE: The function does not track individual clients of the framework
 * and is expected to be maintained by caller of SCMI protocol library.
 * scmi_handle_put must be balanced with successful scmi_handle_get
 *
 * Return: 0 is successfully released
 *	if null was passed, it returns -EINVAL;
 */
int scmi_handle_put(const struct scmi_handle *handle)
{
	struct scmi_info *info;

	if (!handle)
		return -EINVAL;

	info = handle_to_scmi_info(handle);
	mutex_lock(&scmi_list_mutex);
	if (!WARN_ON(!info->users))
		info->users--;
	mutex_unlock(&scmi_list_mutex);

	return 0;
}

static int __scmi_xfer_info_init(struct scmi_info *sinfo,
				 struct scmi_xfers_info *info)
{
	int i;
	struct scmi_xfer *xfer;
	struct device *dev = sinfo->dev;
	const struct scmi_desc *desc = sinfo->desc;

	/* Pre-allocated messages, no more than what hdr.seq can support */
	if (WARN_ON(!info->max_msg || info->max_msg > MSG_TOKEN_MAX)) {
		dev_err(dev,
			"Invalid maximum messages %d, not in range [1 - %lu]\n",
			info->max_msg, MSG_TOKEN_MAX);
		return -EINVAL;
	}

	hash_init(info->pending_xfers);

	/* Allocate a bitmask sized to hold MSG_TOKEN_MAX tokens */
	info->xfer_alloc_table = devm_kcalloc(dev, BITS_TO_LONGS(MSG_TOKEN_MAX),
					      sizeof(long), GFP_KERNEL);
	if (!info->xfer_alloc_table)
		return -ENOMEM;

	/*
	 * Preallocate a number of xfers equal to max inflight messages,
	 * pre-initialize the buffer pointer to pre-allocated buffers and
	 * attach all of them to the free list
	 */
	INIT_HLIST_HEAD(&info->free_xfers);
	for (i = 0; i < info->max_msg; i++) {
		xfer = devm_kzalloc(dev, sizeof(*xfer), GFP_KERNEL);
		if (!xfer)
			return -ENOMEM;

		xfer->rx.buf = devm_kcalloc(dev, sizeof(u8), desc->max_msg_size,
					    GFP_KERNEL);
		if (!xfer->rx.buf)
			return -ENOMEM;

		xfer->tx.buf = xfer->rx.buf;
		init_completion(&xfer->done);
		spin_lock_init(&xfer->lock);

		/* Add initialized xfer to the free list */
		hlist_add_head(&xfer->node, &info->free_xfers);
	}

	spin_lock_init(&info->xfer_lock);

	return 0;
}

static int scmi_channels_max_msg_configure(struct scmi_info *sinfo)
{
	const struct scmi_desc *desc = sinfo->desc;

	if (!desc->ops->get_max_msg) {
		sinfo->tx_minfo.max_msg = desc->max_msg;
		sinfo->rx_minfo.max_msg = desc->max_msg;
	} else {
		struct scmi_chan_info *base_cinfo;

		base_cinfo = idr_find(&sinfo->tx_idr, SCMI_PROTOCOL_BASE);
		if (!base_cinfo)
			return -EINVAL;
		sinfo->tx_minfo.max_msg = desc->ops->get_max_msg(base_cinfo);

		/* RX channel is optional so can be skipped */
		base_cinfo = idr_find(&sinfo->rx_idr, SCMI_PROTOCOL_BASE);
		if (base_cinfo)
			sinfo->rx_minfo.max_msg =
				desc->ops->get_max_msg(base_cinfo);
	}

	return 0;
}

static int scmi_xfer_info_init(struct scmi_info *sinfo)
{
	int ret;

	ret = scmi_channels_max_msg_configure(sinfo);
	if (ret)
		return ret;

	ret = __scmi_xfer_info_init(sinfo, &sinfo->tx_minfo);
	if (!ret && idr_find(&sinfo->rx_idr, SCMI_PROTOCOL_BASE))
		ret = __scmi_xfer_info_init(sinfo, &sinfo->rx_minfo);

	return ret;
}

static int scmi_chan_setup(struct scmi_info *info, struct device *dev,
			   int prot_id, bool tx)
{
	int ret, idx;
	struct scmi_chan_info *cinfo;
	struct idr *idr;

	/* Transmit channel is first entry i.e. index 0 */
	idx = tx ? 0 : 1;
	idr = tx ? &info->tx_idr : &info->rx_idr;

	/* check if already allocated, used for multiple device per protocol */
	cinfo = idr_find(idr, prot_id);
	if (cinfo)
		return 0;

	if (!info->desc->ops->chan_available(dev, idx)) {
		cinfo = idr_find(idr, SCMI_PROTOCOL_BASE);
		if (unlikely(!cinfo)) /* Possible only if platform has no Rx */
			return -EINVAL;
		goto idr_alloc;
	}

	cinfo = devm_kzalloc(info->dev, sizeof(*cinfo), GFP_KERNEL);
	if (!cinfo)
		return -ENOMEM;

	cinfo->dev = dev;
	cinfo->rx_timeout_ms = info->desc->max_rx_timeout_ms;

	ret = info->desc->ops->chan_setup(cinfo, info->dev, tx);
	if (ret)
		return ret;

	if (tx && is_polling_required(cinfo, info)) {
		if (is_transport_polling_capable(info))
			dev_info(dev,
				 "Enabled polling mode TX channel - prot_id:%d\n",
				 prot_id);
		else
			dev_warn(dev,
				 "Polling mode NOT supported by transport.\n");
	}

idr_alloc:
	ret = idr_alloc(idr, cinfo, prot_id, prot_id + 1, GFP_KERNEL);
	if (ret != prot_id) {
		dev_err(dev, "unable to allocate SCMI idr slot err %d\n", ret);
		return ret;
	}

	cinfo->handle = &info->handle;
	return 0;
}

static inline int
scmi_txrx_setup(struct scmi_info *info, struct device *dev, int prot_id)
{
	int ret = scmi_chan_setup(info, dev, prot_id, true);

	if (!ret) {
		/* Rx is optional, report only memory errors */
		ret = scmi_chan_setup(info, dev, prot_id, false);
		if (ret && ret != -ENOMEM)
			ret = 0;
	}

	return ret;
}

/**
 * scmi_get_protocol_device  - Helper to get/create an SCMI device.
 *
 * @np: A device node representing a valid active protocols for the referred
 * SCMI instance.
 * @info: The referred SCMI instance for which we are getting/creating this
 * device.
 * @prot_id: The protocol ID.
 * @name: The device name.
 *
 * Referring to the specific SCMI instance identified by @info, this helper
 * takes care to return a properly initialized device matching the requested
 * @proto_id and @name: if device was still not existent it is created as a
 * child of the specified SCMI instance @info and its transport properly
 * initialized as usual.
 *
 * Return: A properly initialized scmi device, NULL otherwise.
 */
static inline struct scmi_device *
scmi_get_protocol_device(struct device_node *np, struct scmi_info *info,
			 int prot_id, const char *name)
{
	struct scmi_device *sdev;

	/* Already created for this parent SCMI instance ? */
	sdev = scmi_child_dev_find(info->dev, prot_id, name);
	if (sdev)
		return sdev;

	mutex_lock(&scmi_syspower_mtx);
	if (prot_id == SCMI_PROTOCOL_SYSTEM && scmi_syspower_registered) {
		dev_warn(info->dev,
			 "SCMI SystemPower protocol device must be unique !\n");
		mutex_unlock(&scmi_syspower_mtx);

		return NULL;
	}

	pr_debug("Creating SCMI device (%s) for protocol %x\n", name, prot_id);

	sdev = scmi_device_create(np, info->dev, prot_id, name);
	if (!sdev) {
		dev_err(info->dev, "failed to create %d protocol device\n",
			prot_id);
		mutex_unlock(&scmi_syspower_mtx);

		return NULL;
	}

	if (scmi_txrx_setup(info, &sdev->dev, prot_id)) {
		dev_err(&sdev->dev, "failed to setup transport\n");
		scmi_device_destroy(sdev);
		mutex_unlock(&scmi_syspower_mtx);

		return NULL;
	}

	if (prot_id == SCMI_PROTOCOL_SYSTEM)
		scmi_syspower_registered = true;

	mutex_unlock(&scmi_syspower_mtx);

	return sdev;
}

static inline void
scmi_create_protocol_device(struct device_node *np, struct scmi_info *info,
			    int prot_id, const char *name)
{
	struct scmi_device *sdev;

	sdev = scmi_get_protocol_device(np, info, prot_id, name);
	if (!sdev)
		return;

	/* setup handle now as the transport is ready */
	scmi_set_handle(sdev);
}

/**
 * scmi_create_protocol_devices  - Create devices for all pending requests for
 * this SCMI instance.
 *
 * @np: The device node describing the protocol
 * @info: The SCMI instance descriptor
 * @prot_id: The protocol ID
 *
 * All devices previously requested for this instance (if any) are found and
 * created by scanning the proper @&scmi_requested_devices entry.
 */
static void scmi_create_protocol_devices(struct device_node *np,
					 struct scmi_info *info, int prot_id)
{
	struct list_head *phead;

	mutex_lock(&scmi_requested_devices_mtx);
	phead = idr_find(&scmi_requested_devices, prot_id);
	if (phead) {
		struct scmi_requested_dev *rdev;

		list_for_each_entry(rdev, phead, node)
			scmi_create_protocol_device(np, info, prot_id,
						    rdev->id_table->name);
	}
	mutex_unlock(&scmi_requested_devices_mtx);
}

/**
 * scmi_protocol_device_request  - Helper to request a device
 *
 * @id_table: A protocol/name pair descriptor for the device to be created.
 *
 * This helper let an SCMI driver request specific devices identified by the
 * @id_table to be created for each active SCMI instance.
 *
 * The requested device name MUST NOT be already existent for any protocol;
 * at first the freshly requested @id_table is annotated in the IDR table
 * @scmi_requested_devices, then a matching device is created for each already
 * active SCMI instance. (if any)
 *
 * This way the requested device is created straight-away for all the already
 * initialized(probed) SCMI instances (handles) and it remains also annotated
 * as pending creation if the requesting SCMI driver was loaded before some
 * SCMI instance and related transports were available: when such late instance
 * is probed, its probe will take care to scan the list of pending requested
 * devices and create those on its own (see @scmi_create_protocol_devices and
 * its enclosing loop)
 *
 * Return: 0 on Success
 */
int scmi_protocol_device_request(const struct scmi_device_id *id_table)
{
	int ret = 0;
	unsigned int id = 0;
	struct list_head *head, *phead = NULL;
	struct scmi_requested_dev *rdev;
	struct scmi_info *info;

	pr_debug("Requesting SCMI device (%s) for protocol %x\n",
		 id_table->name, id_table->protocol_id);

	/*
	 * Search for the matching protocol rdev list and then search
	 * of any existent equally named device...fails if any duplicate found.
	 */
	mutex_lock(&scmi_requested_devices_mtx);
	idr_for_each_entry(&scmi_requested_devices, head, id) {
		if (!phead) {
			/* A list found registered in the IDR is never empty */
			rdev = list_first_entry(head, struct scmi_requested_dev,
						node);
			if (rdev->id_table->protocol_id ==
			    id_table->protocol_id)
				phead = head;
		}
		list_for_each_entry(rdev, head, node) {
			if (!strcmp(rdev->id_table->name, id_table->name)) {
				pr_err("Ignoring duplicate request [%d] %s\n",
				       rdev->id_table->protocol_id,
				       rdev->id_table->name);
				ret = -EINVAL;
				goto out;
			}
		}
	}

	/*
	 * No duplicate found for requested id_table, so let's create a new
	 * requested device entry for this new valid request.
	 */
	rdev = kzalloc(sizeof(*rdev), GFP_KERNEL);
	if (!rdev) {
		ret = -ENOMEM;
		goto out;
	}
	rdev->id_table = id_table;

	/*
	 * Append the new requested device table descriptor to the head of the
	 * related protocol list, eventually creating such head if not already
	 * there.
	 */
	if (!phead) {
		phead = kzalloc(sizeof(*phead), GFP_KERNEL);
		if (!phead) {
			kfree(rdev);
			ret = -ENOMEM;
			goto out;
		}
		INIT_LIST_HEAD(phead);

		ret = idr_alloc(&scmi_requested_devices, (void *)phead,
				id_table->protocol_id,
				id_table->protocol_id + 1, GFP_KERNEL);
		if (ret != id_table->protocol_id) {
			pr_err("Failed to save SCMI device - ret:%d\n", ret);
			kfree(rdev);
			kfree(phead);
			ret = -EINVAL;
			goto out;
		}
		ret = 0;
	}
	list_add(&rdev->node, phead);

	/*
	 * Now effectively create and initialize the requested device for every
	 * already initialized SCMI instance which has registered the requested
	 * protocol as a valid active one: i.e. defined in DT and supported by
	 * current platform FW.
	 */
	mutex_lock(&scmi_list_mutex);
	list_for_each_entry(info, &scmi_list, node) {
		struct device_node *child;

		child = idr_find(&info->active_protocols,
				 id_table->protocol_id);
		if (child) {
			struct scmi_device *sdev;

			sdev = scmi_get_protocol_device(child, info,
							id_table->protocol_id,
							id_table->name);
			if (sdev) {
				/* Set handle if not already set: device existed */
				if (!sdev->handle)
					sdev->handle =
						scmi_handle_get_from_info_unlocked(info);
				/* Relink consumer and suppliers */
				if (sdev->handle)
					scmi_device_link_add(&sdev->dev,
							     sdev->handle->dev);
			}
		} else {
			dev_err(info->dev,
				"Failed. SCMI protocol %d not active.\n",
				id_table->protocol_id);
		}
	}
	mutex_unlock(&scmi_list_mutex);

out:
	mutex_unlock(&scmi_requested_devices_mtx);

	return ret;
}

/**
 * scmi_protocol_device_unrequest  - Helper to unrequest a device
 *
 * @id_table: A protocol/name pair descriptor for the device to be unrequested.
 *
 * An helper to let an SCMI driver release its request about devices; note that
 * devices are created and initialized once the first SCMI driver request them
 * but they destroyed only on SCMI core unloading/unbinding.
 *
 * The current SCMI transport layer uses such devices as internal references and
 * as such they could be shared as same transport between multiple drivers so
 * that cannot be safely destroyed till the whole SCMI stack is removed.
 * (unless adding further burden of refcounting.)
 */
void scmi_protocol_device_unrequest(const struct scmi_device_id *id_table)
{
	struct list_head *phead;

	pr_debug("Unrequesting SCMI device (%s) for protocol %x\n",
		 id_table->name, id_table->protocol_id);

	mutex_lock(&scmi_requested_devices_mtx);
	phead = idr_find(&scmi_requested_devices, id_table->protocol_id);
	if (phead) {
		struct scmi_requested_dev *victim, *tmp;

		list_for_each_entry_safe(victim, tmp, phead, node) {
			if (!strcmp(victim->id_table->name, id_table->name)) {
				list_del(&victim->node);
				kfree(victim);
				break;
			}
		}

		if (list_empty(phead)) {
			idr_remove(&scmi_requested_devices,
				   id_table->protocol_id);
			kfree(phead);
		}
	}
	mutex_unlock(&scmi_requested_devices_mtx);
}

static int scmi_cleanup_txrx_channels(struct scmi_info *info)
{
	int ret;
	struct idr *idr = &info->tx_idr;

	ret = idr_for_each(idr, info->desc->ops->chan_free, idr);
	idr_destroy(&info->tx_idr);

	idr = &info->rx_idr;
	ret = idr_for_each(idr, info->desc->ops->chan_free, idr);
	idr_destroy(&info->rx_idr);

	return ret;
}

static int scmi_probe(struct platform_device *pdev)
{
	int ret;
	struct scmi_handle *handle;
	const struct scmi_desc *desc;
	struct scmi_info *info;
	struct device *dev = &pdev->dev;
	struct device_node *child, *np = dev->of_node;

	desc = of_device_get_match_data(dev);
	if (!desc)
		return -EINVAL;

	info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL);
	if (!info)
		return -ENOMEM;

	info->dev = dev;
	info->desc = desc;
	INIT_LIST_HEAD(&info->node);
	idr_init(&info->protocols);
	mutex_init(&info->protocols_mtx);
	idr_init(&info->active_protocols);

	platform_set_drvdata(pdev, info);
	idr_init(&info->tx_idr);
	idr_init(&info->rx_idr);

	handle = &info->handle;
	handle->dev = info->dev;
	handle->version = &info->version;
	handle->devm_protocol_acquire = scmi_devm_protocol_acquire;
	handle->devm_protocol_get = scmi_devm_protocol_get;
	handle->devm_protocol_put = scmi_devm_protocol_put;

	/* System wide atomic threshold for atomic ops .. if any */
	if (!of_property_read_u32(np, "atomic-threshold-us",
				  &info->atomic_threshold))
		dev_info(dev,
			 "SCMI System wide atomic threshold set to %d us\n",
			 info->atomic_threshold);
	handle->is_transport_atomic = scmi_is_transport_atomic;

	if (desc->ops->link_supplier) {
		ret = desc->ops->link_supplier(dev);
		if (ret)
			return ret;
	}

	ret = scmi_txrx_setup(info, dev, SCMI_PROTOCOL_BASE);
	if (ret)
		return ret;

	ret = scmi_xfer_info_init(info);
	if (ret)
		goto clear_txrx_setup;

	if (scmi_notification_init(handle))
		dev_err(dev, "SCMI Notifications NOT available.\n");

	if (info->desc->atomic_enabled && !is_transport_polling_capable(info))
		dev_err(dev,
			"Transport is not polling capable. Atomic mode not supported.\n");

	/*
	 * Trigger SCMI Base protocol initialization.
	 * It's mandatory and won't be ever released/deinit until the
	 * SCMI stack is shutdown/unloaded as a whole.
	 */
	ret = scmi_protocol_acquire(handle, SCMI_PROTOCOL_BASE);
	if (ret) {
		dev_err(dev, "unable to communicate with SCMI\n");
		goto notification_exit;
	}

	mutex_lock(&scmi_list_mutex);
	list_add_tail(&info->node, &scmi_list);
	mutex_unlock(&scmi_list_mutex);

	for_each_available_child_of_node(np, child) {
		u32 prot_id;

		if (of_property_read_u32(child, "reg", &prot_id))
			continue;

		if (!FIELD_FIT(MSG_PROTOCOL_ID_MASK, prot_id))
			dev_err(dev, "Out of range protocol %d\n", prot_id);

		if (!scmi_is_protocol_implemented(handle, prot_id)) {
			dev_err(dev, "SCMI protocol %d not implemented\n",
				prot_id);
			continue;
		}

		/*
		 * Save this valid DT protocol descriptor amongst
		 * @active_protocols for this SCMI instance/
		 */
		ret = idr_alloc(&info->active_protocols, child,
				prot_id, prot_id + 1, GFP_KERNEL);
		if (ret != prot_id) {
			dev_err(dev, "SCMI protocol %d already activated. Skip\n",
				prot_id);
			continue;
		}

		of_node_get(child);
		scmi_create_protocol_devices(child, info, prot_id);
	}

	return 0;

notification_exit:
	scmi_notification_exit(&info->handle);
clear_txrx_setup:
	scmi_cleanup_txrx_channels(info);
	return ret;
}

void scmi_free_channel(struct scmi_chan_info *cinfo, struct idr *idr, int id)
{
	idr_remove(idr, id);
}

static int scmi_remove(struct platform_device *pdev)
{
	int ret, id;
	struct scmi_info *info = platform_get_drvdata(pdev);
	struct device_node *child;

	mutex_lock(&scmi_list_mutex);
	if (info->users)
		dev_warn(&pdev->dev,
			 "Still active SCMI users will be forcibly unbound.\n");
	list_del(&info->node);
	mutex_unlock(&scmi_list_mutex);

	scmi_notification_exit(&info->handle);

	mutex_lock(&info->protocols_mtx);
	idr_destroy(&info->protocols);
	mutex_unlock(&info->protocols_mtx);

	idr_for_each_entry(&info->active_protocols, child, id)
		of_node_put(child);
	idr_destroy(&info->active_protocols);

	/* Safe to free channels since no more users */
	ret = scmi_cleanup_txrx_channels(info);
	if (ret)
		dev_warn(&pdev->dev, "Failed to cleanup SCMI channels.\n");

	return 0;
}

static ssize_t protocol_version_show(struct device *dev,
				     struct device_attribute *attr, char *buf)
{
	struct scmi_info *info = dev_get_drvdata(dev);

	return sprintf(buf, "%u.%u\n", info->version.major_ver,
		       info->version.minor_ver);
}
static DEVICE_ATTR_RO(protocol_version);

static ssize_t firmware_version_show(struct device *dev,
				     struct device_attribute *attr, char *buf)
{
	struct scmi_info *info = dev_get_drvdata(dev);

	return sprintf(buf, "0x%x\n", info->version.impl_ver);
}
static DEVICE_ATTR_RO(firmware_version);

static ssize_t vendor_id_show(struct device *dev,
			      struct device_attribute *attr, char *buf)
{
	struct scmi_info *info = dev_get_drvdata(dev);

	return sprintf(buf, "%s\n", info->version.vendor_id);
}
static DEVICE_ATTR_RO(vendor_id);

static ssize_t sub_vendor_id_show(struct device *dev,
				  struct device_attribute *attr, char *buf)
{
	struct scmi_info *info = dev_get_drvdata(dev);

	return sprintf(buf, "%s\n", info->version.sub_vendor_id);
}
static DEVICE_ATTR_RO(sub_vendor_id);

static struct attribute *versions_attrs[] = {
	&dev_attr_firmware_version.attr,
	&dev_attr_protocol_version.attr,
	&dev_attr_vendor_id.attr,
	&dev_attr_sub_vendor_id.attr,
	NULL,
};
ATTRIBUTE_GROUPS(versions);

/* Each compatible listed below must have descriptor associated with it */
static const struct of_device_id scmi_of_match[] = {
#ifdef CONFIG_ARM_SCMI_TRANSPORT_MAILBOX
	{ .compatible = "arm,scmi", .data = &scmi_mailbox_desc },
#endif
#ifdef CONFIG_ARM_SCMI_TRANSPORT_OPTEE
	{ .compatible = "linaro,scmi-optee", .data = &scmi_optee_desc },
#endif
#ifdef CONFIG_ARM_SCMI_TRANSPORT_SMC
	{ .compatible = "arm,scmi-smc", .data = &scmi_smc_desc},
#endif
#ifdef CONFIG_ARM_SCMI_TRANSPORT_VIRTIO
	{ .compatible = "arm,scmi-virtio", .data = &scmi_virtio_desc},
#endif
	{ /* Sentinel */ },
};

MODULE_DEVICE_TABLE(of, scmi_of_match);

static struct platform_driver scmi_driver = {
	.driver = {
		   .name = "arm-scmi",
		   .suppress_bind_attrs = true,
		   .of_match_table = scmi_of_match,
		   .dev_groups = versions_groups,
		   },
	.probe = scmi_probe,
	.remove = scmi_remove,
};

/**
 * __scmi_transports_setup  - Common helper to call transport-specific
 * .init/.exit code if provided.
 *
 * @init: A flag to distinguish between init and exit.
 *
 * Note that, if provided, we invoke .init/.exit functions for all the
 * transports currently compiled in.
 *
 * Return: 0 on Success.
 */
static inline int __scmi_transports_setup(bool init)
{
	int ret = 0;
	const struct of_device_id *trans;

	for (trans = scmi_of_match; trans->data; trans++) {
		const struct scmi_desc *tdesc = trans->data;

		if ((init && !tdesc->transport_init) ||
		    (!init && !tdesc->transport_exit))
			continue;

		if (init)
			ret = tdesc->transport_init();
		else
			tdesc->transport_exit();

		if (ret) {
			pr_err("SCMI transport %s FAILED initialization!\n",
			       trans->compatible);
			break;
		}
	}

	return ret;
}

static int __init scmi_transports_init(void)
{
	return __scmi_transports_setup(true);
}

static void __exit scmi_transports_exit(void)
{
	__scmi_transports_setup(false);
}

static int __init scmi_driver_init(void)
{
	int ret;

	/* Bail out if no SCMI transport was configured */
	if (WARN_ON(!IS_ENABLED(CONFIG_ARM_SCMI_HAVE_TRANSPORT)))
		return -EINVAL;

	scmi_bus_init();

	/* Initialize any compiled-in transport which provided an init/exit */
	ret = scmi_transports_init();
	if (ret)
		return ret;

	scmi_base_register();

	scmi_clock_register();
	scmi_perf_register();
	scmi_power_register();
	scmi_reset_register();
	scmi_sensors_register();
	scmi_voltage_register();
	scmi_system_register();
	scmi_powercap_register();

	return platform_driver_register(&scmi_driver);
}
subsys_initcall(scmi_driver_init);

static void __exit scmi_driver_exit(void)
{
	scmi_base_unregister();

	scmi_clock_unregister();
	scmi_perf_unregister();
	scmi_power_unregister();
	scmi_reset_unregister();
	scmi_sensors_unregister();
	scmi_voltage_unregister();
	scmi_system_unregister();
	scmi_powercap_unregister();

	scmi_bus_exit();

	scmi_transports_exit();

	platform_driver_unregister(&scmi_driver);
}
module_exit(scmi_driver_exit);

MODULE_ALIAS("platform:arm-scmi");
MODULE_AUTHOR("Sudeep Holla <sudeep.holla@arm.com>");
MODULE_DESCRIPTION("ARM SCMI protocol driver");
MODULE_LICENSE("GPL v2");