drivers/clocksource/timer-cadence-ttc.c

// SPDX-License-Identifier: GPL-2.0-only
/*
 * This file contains driver for the Cadence Triple Timer Counter Rev 06
 *
 *  Copyright (C) 2011-2013 Xilinx
 *
 * based on arch/mips/kernel/time.c timer driver
 */

#include <linux/clk.h>
#include <linux/interrupt.h>
#include <linux/clockchips.h>
#include <linux/clocksource.h>
#include <linux/of_address.h>
#include <linux/of_irq.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
#include <linux/sched_clock.h>
#include <linux/module.h>
#include <linux/of_platform.h>

/*
 * This driver configures the 2 16/32-bit count-up timers as follows:
 *
 * T1: Timer 1, clocksource for generic timekeeping
 * T2: Timer 2, clockevent source for hrtimers
 * T3: Timer 3, <unused>
 *
 * The input frequency to the timer module for emulation is 2.5MHz which is
 * common to all the timer channels (T1, T2, and T3). With a pre-scaler of 32,
 * the timers are clocked at 78.125KHz (12.8 us resolution).

 * The input frequency to the timer module in silicon is configurable and
 * obtained from device tree. The pre-scaler of 32 is used.
 */

/*
 * Timer Register Offset Definitions of Timer 1, Increment base address by 4
 * and use same offsets for Timer 2
 */
#define TTC_CLK_CNTRL_OFFSET		0x00 /* Clock Control Reg, RW */
#define TTC_CNT_CNTRL_OFFSET		0x0C /* Counter Control Reg, RW */
#define TTC_COUNT_VAL_OFFSET		0x18 /* Counter Value Reg, RO */
#define TTC_INTR_VAL_OFFSET		0x24 /* Interval Count Reg, RW */
#define TTC_ISR_OFFSET		0x54 /* Interrupt Status Reg, RO */
#define TTC_IER_OFFSET		0x60 /* Interrupt Enable Reg, RW */

#define TTC_CNT_CNTRL_DISABLE_MASK	0x1

#define TTC_CLK_CNTRL_CSRC_MASK		(1 << 5)	/* clock source */
#define TTC_CLK_CNTRL_PSV_MASK		0x1e
#define TTC_CLK_CNTRL_PSV_SHIFT		1

/*
 * Setup the timers to use pre-scaling, using a fixed value for now that will
 * work across most input frequency, but it may need to be more dynamic
 */
#define PRESCALE_EXPONENT	11	/* 2 ^ PRESCALE_EXPONENT = PRESCALE */
#define PRESCALE		2048	/* The exponent must match this */
#define CLK_CNTRL_PRESCALE	((PRESCALE_EXPONENT - 1) << 1)
#define CLK_CNTRL_PRESCALE_EN	1
#define CNT_CNTRL_RESET		(1 << 4)

#define MAX_F_ERR 50

/**
 * struct ttc_timer - This definition defines local timer structure
 *
 * @base_addr:	Base address of timer
 * @freq:	Timer input clock frequency
 * @clk:	Associated clock source
 * @clk_rate_change_nb:	Notifier block for clock rate changes
 */
struct ttc_timer {
	void __iomem *base_addr;
	unsigned long freq;
	struct clk *clk;
	struct notifier_block clk_rate_change_nb;
};

#define to_ttc_timer(x) \
		container_of(x, struct ttc_timer, clk_rate_change_nb)

struct ttc_timer_clocksource {
	u32			scale_clk_ctrl_reg_old;
	u32			scale_clk_ctrl_reg_new;
	struct ttc_timer	ttc;
	struct clocksource	cs;
};

#define to_ttc_timer_clksrc(x) \
		container_of(x, struct ttc_timer_clocksource, cs)

struct ttc_timer_clockevent {
	struct ttc_timer		ttc;
	struct clock_event_device	ce;
};

#define to_ttc_timer_clkevent(x) \
		container_of(x, struct ttc_timer_clockevent, ce)

static void __iomem *ttc_sched_clock_val_reg;

/**
 * ttc_set_interval - Set the timer interval value
 *
 * @timer:	Pointer to the timer instance
 * @cycles:	Timer interval ticks
 **/
static void ttc_set_interval(struct ttc_timer *timer,
					unsigned long cycles)
{
	u32 ctrl_reg;

	/* Disable the counter, set the counter value  and re-enable counter */
	ctrl_reg = readl_relaxed(timer->base_addr + TTC_CNT_CNTRL_OFFSET);
	ctrl_reg |= TTC_CNT_CNTRL_DISABLE_MASK;
	writel_relaxed(ctrl_reg, timer->base_addr + TTC_CNT_CNTRL_OFFSET);

	writel_relaxed(cycles, timer->base_addr + TTC_INTR_VAL_OFFSET);

	/*
	 * Reset the counter (0x10) so that it starts from 0, one-shot
	 * mode makes this needed for timing to be right.
	 */
	ctrl_reg |= CNT_CNTRL_RESET;
	ctrl_reg &= ~TTC_CNT_CNTRL_DISABLE_MASK;
	writel_relaxed(ctrl_reg, timer->base_addr + TTC_CNT_CNTRL_OFFSET);
}

/**
 * ttc_clock_event_interrupt - Clock event timer interrupt handler
 *
 * @irq:	IRQ number of the Timer
 * @dev_id:	void pointer to the ttc_timer instance
 *
 * Returns: Always IRQ_HANDLED - success
 **/
static irqreturn_t ttc_clock_event_interrupt(int irq, void *dev_id)
{
	struct ttc_timer_clockevent *ttce = dev_id;
	struct ttc_timer *timer = &ttce->ttc;

	/* Acknowledge the interrupt and call event handler */
	readl_relaxed(timer->base_addr + TTC_ISR_OFFSET);

	ttce->ce.event_handler(&ttce->ce);

	return IRQ_HANDLED;
}

/**
 * __ttc_clocksource_read - Reads the timer counter register
 * @cs: &clocksource to read from
 *
 * Returns: Current timer counter register value
 **/
static u64 __ttc_clocksource_read(struct clocksource *cs)
{
	struct ttc_timer *timer = &to_ttc_timer_clksrc(cs)->ttc;

	return (u64)readl_relaxed(timer->base_addr +
				TTC_COUNT_VAL_OFFSET);
}

static u64 notrace ttc_sched_clock_read(void)
{
	return readl_relaxed(ttc_sched_clock_val_reg);
}

/**
 * ttc_set_next_event - Sets the time interval for next event
 *
 * @cycles:	Timer interval ticks
 * @evt:	Address of clock event instance
 *
 * Returns: Always %0 - success
 **/
static int ttc_set_next_event(unsigned long cycles,
					struct clock_event_device *evt)
{
	struct ttc_timer_clockevent *ttce = to_ttc_timer_clkevent(evt);
	struct ttc_timer *timer = &ttce->ttc;

	ttc_set_interval(timer, cycles);
	return 0;
}

/**
 * ttc_shutdown - Sets the state of timer
 * @evt:	Address of clock event instance
 *
 * Used for shutdown or oneshot.
 *
 * Returns: Always %0 - success
 **/
static int ttc_shutdown(struct clock_event_device *evt)
{
	struct ttc_timer_clockevent *ttce = to_ttc_timer_clkevent(evt);
	struct ttc_timer *timer = &ttce->ttc;
	u32 ctrl_reg;

	ctrl_reg = readl_relaxed(timer->base_addr + TTC_CNT_CNTRL_OFFSET);
	ctrl_reg |= TTC_CNT_CNTRL_DISABLE_MASK;
	writel_relaxed(ctrl_reg, timer->base_addr + TTC_CNT_CNTRL_OFFSET);
	return 0;
}

/**
 * ttc_set_periodic - Sets the state of timer
 * @evt:	Address of clock event instance
 *
 * Returns: Always %0 - success
 */
static int ttc_set_periodic(struct clock_event_device *evt)
{
	struct ttc_timer_clockevent *ttce = to_ttc_timer_clkevent(evt);
	struct ttc_timer *timer = &ttce->ttc;

	ttc_set_interval(timer,
			 DIV_ROUND_CLOSEST(ttce->ttc.freq, PRESCALE * HZ));
	return 0;
}

static int ttc_resume(struct clock_event_device *evt)
{
	struct ttc_timer_clockevent *ttce = to_ttc_timer_clkevent(evt);
	struct ttc_timer *timer = &ttce->ttc;
	u32 ctrl_reg;

	ctrl_reg = readl_relaxed(timer->base_addr + TTC_CNT_CNTRL_OFFSET);
	ctrl_reg &= ~TTC_CNT_CNTRL_DISABLE_MASK;
	writel_relaxed(ctrl_reg, timer->base_addr + TTC_CNT_CNTRL_OFFSET);
	return 0;
}

static int ttc_rate_change_clocksource_cb(struct notifier_block *nb,
		unsigned long event, void *data)
{
	struct clk_notifier_data *ndata = data;
	struct ttc_timer *ttc = to_ttc_timer(nb);
	struct ttc_timer_clocksource *ttccs = container_of(ttc,
			struct ttc_timer_clocksource, ttc);

	switch (event) {
	case PRE_RATE_CHANGE:
	{
		u32 psv;
		unsigned long factor, rate_low, rate_high;

		if (ndata->new_rate > ndata->old_rate) {
			factor = DIV_ROUND_CLOSEST(ndata->new_rate,
					ndata->old_rate);
			rate_low = ndata->old_rate;
			rate_high = ndata->new_rate;
		} else {
			factor = DIV_ROUND_CLOSEST(ndata->old_rate,
					ndata->new_rate);
			rate_low = ndata->new_rate;
			rate_high = ndata->old_rate;
		}

		if (!is_power_of_2(factor))
				return NOTIFY_BAD;

		if (abs(rate_high - (factor * rate_low)) > MAX_F_ERR)
			return NOTIFY_BAD;

		factor = __ilog2_u32(factor);

		/*
		 * store timer clock ctrl register so we can restore it in case
		 * of an abort.
		 */
		ttccs->scale_clk_ctrl_reg_old =
			readl_relaxed(ttccs->ttc.base_addr +
			TTC_CLK_CNTRL_OFFSET);

		psv = (ttccs->scale_clk_ctrl_reg_old &
				TTC_CLK_CNTRL_PSV_MASK) >>
				TTC_CLK_CNTRL_PSV_SHIFT;
		if (ndata->new_rate < ndata->old_rate)
			psv -= factor;
		else
			psv += factor;

		/* prescaler within legal range? */
		if (psv & ~(TTC_CLK_CNTRL_PSV_MASK >> TTC_CLK_CNTRL_PSV_SHIFT))
			return NOTIFY_BAD;

		ttccs->scale_clk_ctrl_reg_new = ttccs->scale_clk_ctrl_reg_old &
			~TTC_CLK_CNTRL_PSV_MASK;
		ttccs->scale_clk_ctrl_reg_new |= psv << TTC_CLK_CNTRL_PSV_SHIFT;


		/* scale down: adjust divider in post-change notification */
		if (ndata->new_rate < ndata->old_rate)
			return NOTIFY_DONE;

		/* scale up: adjust divider now - before frequency change */
		writel_relaxed(ttccs->scale_clk_ctrl_reg_new,
			       ttccs->ttc.base_addr + TTC_CLK_CNTRL_OFFSET);
		break;
	}
	case POST_RATE_CHANGE:
		/* scale up: pre-change notification did the adjustment */
		if (ndata->new_rate > ndata->old_rate)
			return NOTIFY_OK;

		/* scale down: adjust divider now - after frequency change */
		writel_relaxed(ttccs->scale_clk_ctrl_reg_new,
			       ttccs->ttc.base_addr + TTC_CLK_CNTRL_OFFSET);
		break;

	case ABORT_RATE_CHANGE:
		/* we have to undo the adjustment in case we scale up */
		if (ndata->new_rate < ndata->old_rate)
			return NOTIFY_OK;

		/* restore original register value */
		writel_relaxed(ttccs->scale_clk_ctrl_reg_old,
			       ttccs->ttc.base_addr + TTC_CLK_CNTRL_OFFSET);
		fallthrough;
	default:
		return NOTIFY_DONE;
	}

	return NOTIFY_DONE;
}

static int __init ttc_setup_clocksource(struct clk *clk, void __iomem *base,
					 u32 timer_width)
{
	struct ttc_timer_clocksource *ttccs;
	int err;

	ttccs = kzalloc(sizeof(*ttccs), GFP_KERNEL);
	if (!ttccs)
		return -ENOMEM;

	ttccs->ttc.clk = clk;

	err = clk_prepare_enable(ttccs->ttc.clk);
	if (err) {
		kfree(ttccs);
		return err;
	}

	ttccs->ttc.freq = clk_get_rate(ttccs->ttc.clk);

	ttccs->ttc.clk_rate_change_nb.notifier_call =
		ttc_rate_change_clocksource_cb;
	ttccs->ttc.clk_rate_change_nb.next = NULL;

	err = clk_notifier_register(ttccs->ttc.clk,
				    &ttccs->ttc.clk_rate_change_nb);
	if (err)
		pr_warn("Unable to register clock notifier.\n");

	ttccs->ttc.base_addr = base;
	ttccs->cs.name = "ttc_clocksource";
	ttccs->cs.rating = 200;
	ttccs->cs.read = __ttc_clocksource_read;
	ttccs->cs.mask = CLOCKSOURCE_MASK(timer_width);
	ttccs->cs.flags = CLOCK_SOURCE_IS_CONTINUOUS;

	/*
	 * Setup the clock source counter to be an incrementing counter
	 * with no interrupt and it rolls over at 0xFFFF. Pre-scale
	 * it by 32 also. Let it start running now.
	 */
	writel_relaxed(0x0,  ttccs->ttc.base_addr + TTC_IER_OFFSET);
	writel_relaxed(CLK_CNTRL_PRESCALE | CLK_CNTRL_PRESCALE_EN,
		     ttccs->ttc.base_addr + TTC_CLK_CNTRL_OFFSET);
	writel_relaxed(CNT_CNTRL_RESET,
		     ttccs->ttc.base_addr + TTC_CNT_CNTRL_OFFSET);

	err = clocksource_register_hz(&ttccs->cs, ttccs->ttc.freq / PRESCALE);
	if (err) {
		kfree(ttccs);
		return err;
	}

	ttc_sched_clock_val_reg = base + TTC_COUNT_VAL_OFFSET;
	sched_clock_register(ttc_sched_clock_read, timer_width,
			     ttccs->ttc.freq / PRESCALE);

	return 0;
}

static int ttc_rate_change_clockevent_cb(struct notifier_block *nb,
		unsigned long event, void *data)
{
	struct clk_notifier_data *ndata = data;
	struct ttc_timer *ttc = to_ttc_timer(nb);
	struct ttc_timer_clockevent *ttcce = container_of(ttc,
			struct ttc_timer_clockevent, ttc);

	switch (event) {
	case POST_RATE_CHANGE:
		/* update cached frequency */
		ttc->freq = ndata->new_rate;

		clockevents_update_freq(&ttcce->ce, ndata->new_rate / PRESCALE);

		fallthrough;
	case PRE_RATE_CHANGE:
	case ABORT_RATE_CHANGE:
	default:
		return NOTIFY_DONE;
	}
}

static int __init ttc_setup_clockevent(struct clk *clk,
				       void __iomem *base, u32 irq)
{
	struct ttc_timer_clockevent *ttcce;
	int err;

	ttcce = kzalloc(sizeof(*ttcce), GFP_KERNEL);
	if (!ttcce)
		return -ENOMEM;

	ttcce->ttc.clk = clk;

	err = clk_prepare_enable(ttcce->ttc.clk);
	if (err)
		goto out_kfree;

	ttcce->ttc.clk_rate_change_nb.notifier_call =
		ttc_rate_change_clockevent_cb;
	ttcce->ttc.clk_rate_change_nb.next = NULL;

	err = clk_notifier_register(ttcce->ttc.clk,
				    &ttcce->ttc.clk_rate_change_nb);
	if (err) {
		pr_warn("Unable to register clock notifier.\n");
		goto out_clk_unprepare;
	}

	ttcce->ttc.freq = clk_get_rate(ttcce->ttc.clk);

	ttcce->ttc.base_addr = base;
	ttcce->ce.name = "ttc_clockevent";
	ttcce->ce.features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT;
	ttcce->ce.set_next_event = ttc_set_next_event;
	ttcce->ce.set_state_shutdown = ttc_shutdown;
	ttcce->ce.set_state_periodic = ttc_set_periodic;
	ttcce->ce.set_state_oneshot = ttc_shutdown;
	ttcce->ce.tick_resume = ttc_resume;
	ttcce->ce.rating = 200;
	ttcce->ce.irq = irq;
	ttcce->ce.cpumask = cpu_possible_mask;

	/*
	 * Setup the clock event timer to be an interval timer which
	 * is prescaled by 32 using the interval interrupt. Leave it
	 * disabled for now.
	 */
	writel_relaxed(0x23, ttcce->ttc.base_addr + TTC_CNT_CNTRL_OFFSET);
	writel_relaxed(CLK_CNTRL_PRESCALE | CLK_CNTRL_PRESCALE_EN,
		     ttcce->ttc.base_addr + TTC_CLK_CNTRL_OFFSET);
	writel_relaxed(0x1,  ttcce->ttc.base_addr + TTC_IER_OFFSET);

	err = request_irq(irq, ttc_clock_event_interrupt,
			  IRQF_TIMER, ttcce->ce.name, ttcce);
	if (err)
		goto out_clk_unprepare;

	clockevents_config_and_register(&ttcce->ce,
			ttcce->ttc.freq / PRESCALE, 1, 0xfffe);

	return 0;

out_clk_unprepare:
	clk_disable_unprepare(ttcce->ttc.clk);
out_kfree:
	kfree(ttcce);
	return err;
}

static int __init ttc_timer_probe(struct platform_device *pdev)
{
	unsigned int irq;
	void __iomem *timer_baseaddr;
	struct clk *clk_cs, *clk_ce;
	static int initialized;
	int clksel, ret;
	u32 timer_width = 16;
	struct device_node *timer = pdev->dev.of_node;

	if (initialized)
		return 0;

	initialized = 1;

	/*
	 * Get the 1st Triple Timer Counter (TTC) block from the device tree
	 * and use it. Note that the event timer uses the interrupt and it's the
	 * 2nd TTC hence the irq_of_parse_and_map(,1)
	 */
	timer_baseaddr = devm_of_iomap(&pdev->dev, timer, 0, NULL);
	if (IS_ERR(timer_baseaddr)) {
		pr_err("ERROR: invalid timer base address\n");
		return PTR_ERR(timer_baseaddr);
	}

	irq = irq_of_parse_and_map(timer, 1);
	if (irq <= 0) {
		pr_err("ERROR: invalid interrupt number\n");
		return -EINVAL;
	}

	of_property_read_u32(timer, "timer-width", &timer_width);

	clksel = readl_relaxed(timer_baseaddr + TTC_CLK_CNTRL_OFFSET);
	clksel = !!(clksel & TTC_CLK_CNTRL_CSRC_MASK);
	clk_cs = of_clk_get(timer, clksel);
	if (IS_ERR(clk_cs)) {
		pr_err("ERROR: timer input clock not found\n");
		return PTR_ERR(clk_cs);
	}

	clksel = readl_relaxed(timer_baseaddr + 4 + TTC_CLK_CNTRL_OFFSET);
	clksel = !!(clksel & TTC_CLK_CNTRL_CSRC_MASK);
	clk_ce = of_clk_get(timer, clksel);
	if (IS_ERR(clk_ce)) {
		pr_err("ERROR: timer input clock not found\n");
		ret = PTR_ERR(clk_ce);
		goto put_clk_cs;
	}

	ret = ttc_setup_clocksource(clk_cs, timer_baseaddr, timer_width);
	if (ret)
		goto put_clk_ce;

	ret = ttc_setup_clockevent(clk_ce, timer_baseaddr + 4, irq);
	if (ret)
		goto put_clk_ce;

	pr_info("%pOFn #0 at %p, irq=%d\n", timer, timer_baseaddr, irq);

	return 0;

put_clk_ce:
	clk_put(clk_ce);
put_clk_cs:
	clk_put(clk_cs);
	return ret;
}

static const struct of_device_id ttc_timer_of_match[] = {
	{.compatible = "cdns,ttc"},
	{},
};

MODULE_DEVICE_TABLE(of, ttc_timer_of_match);

static struct platform_driver ttc_timer_driver = {
	.driver = {
		.name	= "cdns_ttc_timer",
		.of_match_table = ttc_timer_of_match,
	},
};
builtin_platform_driver_probe(ttc_timer_driver, ttc_timer_probe);